Yj4600 PDF

YJ4600
Area-Imaging Scanner
User’s Guide
™
Disclaimer
Youjie reserves the right to make changes in specifications and other informa-
tion contained in this document without prior notice, and the reader should in all
cases consult Youjie to determine whether any such changes have been made.
The information in this publication does not represent a commitment on the part
of Youjie.
Youjie shall not be liable for technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages resulting from the furnish-
ing, performance, or use of this material.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied, repro-
duced, or translated into another language without the prior written consent of
Youjie.
Copyright 2012. All rights reserved.
Microsoft® Windows® is a trademark or registered trademark of Microsoft Cor-
poration.
Other product names or marks mentioned in this document may be trademarks
or registered trademarks of other companies and are the property of their
respective owners.
Product Agency Compliance
Europe
The CE marking indicates compliance to 2004/108/EC EMC Direc-
tive with Standards EN55022 CLASS B, EN55024, EN61000-3-2,
EN61000-3-3. In addition, complies to 2006/95/EC Low Voltage
Directive, when shipped with recommended power supply.
Youjie shall not be liable for use of our product with equipment (i.e., power
supplies, personal computers, etc.) that is not CE marked and does not
comply with the Low Voltage Directive.
Waste Electrical and Electronic Equipment

Information
Youjie complies with Directive 2002/96/EC OF THE EUROPEAN PARLIA-
MENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and
electronic equipment (WEEE).
This product has required the extraction and use of natural resources for its
production. It may contain hazardous substances that could impact health
and the environment, if not properly disposed.
In order to avoid the dissemination of those substances in our environment
and to diminish the pressure on the natural resources, we encourage you to
use the appropriate take-back systems for product disposal. Those sys-
tems will reuse or recycle most of the materials of the product you are dis-
posing in a sound way.
The crossed out wheeled bin symbol informs you that the product
should not be disposed of along with municipal waste and invites you to
use the appropriate separate take-back systems for product disposal.
If you need more information on the collection, reuse, and recycling sys-
tems, please contact your local or regional waste administration.
You may also contact your supplier for more information on the environ-
mental performances of this product.
Russia
Gost-R certificate
International
LED Safety Statement
The LED has been tested and classified as “EXEMPT RISK GROUP” to
the standard: IEC 62471:2006.
CB Scheme
Certified to CB Scheme IEC 60950-1, Second Edition.
Solids and Water Protection

The Youjie 4600 has a rating of IP40, immunity of foreign particles and dripping
water.
Warning
To reduce the possibility of heat-related injuries, avoid touching sec-
tions of the scanner that feel warm.
!
Required Safety Labels
Compliance Markings
information, Part Number,
and Serial Number
information
Table of Contents
Chapter 1 - Getting Started

About This Manual ...................................................... 1-1
Unpacking Your Device............................................... 1-1
Connecting the Device ................................................ 1-1
Connecting with USB ............................................ 1-1
Connecting with Keyboard Wedge ........................ 1-2
Reading Techniques ................................................... 1-3
Menu Bar Code Security Settings ............................... 1-3
Setting Custom Defaults ............................................. 1-4
Resetting the Custom Defaults ................................... 1-4
Resetting the Factory Defaults .................................... 1-5
Chapter 2 - Programming the Interface

Introduction ................................................................. 2-1
Programming the Interface - Plug and Play ................ 2-1
Keyboard Wedge ........................................................ 2-1
Laptop Direct Connect ................................................ 2-1
USB IBM SurePos....................................................... 2-2
USB PC or Macintosh Keyboard ................................. 2-2
USB HID...................................................................... 2-3
Keyboard Country Layout ........................................... 2-4
Keyboard Style .......................................................... 2-10
Keyboard Conversion................................................ 2-12
Control Character Output .......................................... 2-12
Keyboard Modifiers ................................................... 2-13
Chapter 3 - Input/Output Settings

Power Up Beeper ........................................................ 3-1
Trigger Click ................................................................ 3-1
Good Read and Error Indicators ................................. 3-2
Beeper – Good Read ............................................ 3-2
Beeper Volume – Good Read ............................... 3-2
Beeper Pitch – Good Read ................................... 3-3
i
Beeper Pitch – Error .............................................. 3-3
Beeper Duration – Good Read .............................. 3-3
LED – Good Read ................................................. 3-4
Number of Beeps – Good Read ............................ 3-4
Number of Beeps – Error ....................................... 3-4
Good Read Delay .................................................. 3-5
User-Specified Good Read Delay.......................... 3-5
Manual Trigger Mode...................................................3-5
Presentation Mode.......................................................3-6
Presentation Sensitivity ......................................... 3-6
Presentation Centering .......................................... 3-6
Mobile Phone Read Mode ...........................................3-8
Hands Free Time-Out ..................................................3-9
Reread Delay...............................................................3-9
User-Specified Reread Delay ....................................3-10
Scanner Time-Out .....................................................3-10
Centering ...................................................................3-10
No Read.....................................................................3-12
Video Reverse ...........................................................3-13
Working Orientation ...................................................3-14
Chapter 4 - Data Editing

Prefix/Suffix Overview..................................................4-1
To Add a Prefix or Suffix: ....................................... 4-1
To Clear One or All Prefixes or Suffixes ................ 4-2
To Add a Carriage Return Suffix
to All Symbologies............................................ 4-3
Prefix Selections ..........................................................4-3
Suffix Selections ..........................................................4-4
Function Code Transmit ..............................................4-4
Intercharacter, Interfunction,
and Intermessage Delays..........................................4-4
Intercharacter Delay .............................................. 4-5
User Specified Intercharacter Delay ...................... 4-5
Interfunction Delay ................................................. 4-6
Intermessage Delay ............................................... 4-6
ii
Chapter 5 - Data Formatting
Data Format Editor Introduction .................................. 5-1
Add a Data Format ...................................................... 5-1
Other Programming Selections ............................. 5-3
Terminal ID Table........................................................ 5-4
Data Format Editor Commands .................................. 5-4
Move Commands .................................................. 5-5
Search Commands................................................ 5-5
Miscellaneous Commands .................................... 5-6
Data Formatter ............................................................ 5-7
Primary/Alternate Data Formats.................................. 5-8
Chapter 6 - Symbologies
All Symbologies........................................................... 6-2
Message Length Description....................................... 6-2
Codabar ...................................................................... 6-3
Codabar Concatenation ........................................ 6-4
Code 39....................................................................... 6-6
Full ASCII .............................................................. 6-8
Code 39 Code Page.............................................. 6-9
Interleaved 2 of 5 ...................................................... 6-10
NEC 2 of 5................................................................. 6-11
Code 93..................................................................... 6-13
Code 93 Code Page............................................ 6-14
Straight 2 of 5 Industrial (three-bar start/stop) .......... 6-15
Straight 2 of 5 IATA (two-bar start/stop).................... 6-16
Matrix 2 of 5 .............................................................. 6-17
Code 128................................................................... 6-18
ISBT 128 Concatenation ..................................... 6-18
Code 128 Code Page.......................................... 6-19
GS1-128 .................................................................... 6-20
UPC-A ....................................................................... 6-21
UPC-A/EAN-13
with Extended Coupon Code .................................. 6-23
Coupon GS1 DataBar Output ................................... 6-24
UPC-E0 ..................................................................... 6-24
iii
UPC-E1......................................................................6-27
EAN/JAN-13 ..............................................................6-27
ISBN Translate .................................................... 6-29
EAN/JAN-8 ................................................................6-30
MSI ............................................................................6-32
GS1 DataBar Omnidirectional ...................................6-34
GS1 DataBar Limited.................................................6-34
GS1 DataBar Expanded ............................................6-35
Codablock A ..............................................................6-36
Codablock F...............................................................6-37
PDF417......................................................................6-38
MacroPDF417............................................................6-39
MicroPDF417.............................................................6-39
GS1 Composite Codes ..............................................6-40
UPC/EAN Version................................................ 6-40
GS1 Emulation...........................................................6-41
TCIF Linked Code 39 (TLC39) ..................................6-42
QR Code....................................................................6-43
QR Code Page .................................................... 6-44
Data Matrix ................................................................6-45
Data Matrix Code Page ....................................... 6-46
Aztec Code ................................................................6-47
Aztec Code Page ................................................. 6-48
Chinese Sensible (Han Xin) Code .............................6-49
Postal Codes - Linear ................................................6-49
China Post (Hong Kong 2 of 5) ............................ 6-49
Korea Post ........................................................... 6-51
Chapter 7 - Interface Keys

Keyboard Function Relationships ................................7-1
Supported Interface Keys ............................................7-3
Chapter 8 - Utilities
To Add a Test Code I.D. Prefix to All
Symbologies..............................................................8-1
Show Decoder Revision ..............................................8-1
iv
Show Scan Driver Revision......................................... 8-1
Show Software Revision ............................................. 8-1
Show Data Format ...................................................... 8-2
Test Menu ................................................................... 8-2
Chapter 9 - Product Specifications

Youjie 4600 Scanner Product Specifications .............. 9-1
Standard Cable Pinouts .............................................. 9-2
Keyboard Wedge................................................... 9-2
USB ....................................................................... 9-3
.............................................................................. 9-4
Chapter 10 - Maintenance
Repairs ...................................................................... 10-1
Maintenance.............................................................. 10-1
Cleaning the Device ............................................ 10-1
Inspecting Cords and Connectors ....................... 10-1
Replacing Cables ...................................................... 10-1
Replacing an Interface Cable .............................. 10-2
Troubleshooting a Youjie 4600 Scanner ................... 10-2
Chapter 11 - Customer Support

Technical Assistance ................................................ 11-1
Appendix A - Reference Charts

Symbology Chart.........................................................A-1
ASCII Conversion Chart (Code Page 1252) ...............A-4
Code Page Mapping of Printed Bar Codes .................A-6
Unicode Key Maps ......................................................A-8
v
vi
1
Getting Started
About This Manual

This User’s Guide provides installation and programming instructions for
the Youjie 4600 area-imaging scanner. Product specifications, dimensions,
warranty, and customer support information are also included.
Youjie bar code scanners are factory programmed for the most common termi-
nal and communications settings. If you need to change these settings, pro-
gramming is accomplished by scanning the bar codes in this guide.
An asterisk (*) next to an option indicates the default setting.
Unpacking Your Device

After you open the shipping carton containing the product, take the following
steps:
• Check for damage during shipment. Report damage immediately to the
carrier who delivered the carton.
• Make sure the items in the carton match your order.
• Save the shipping container for later storage or shipping.
Connecting the Device

Connecting with USB
A scanner can be connected to the USB port of a computer.
1. Connect the appropriate interface cable to the device first, then to the
computer.
2. The scanner beeps.
1-1
3. Verify the scanner operation by scanning a bar code from the Sample
Symbols in the back of this manual.
The unit defaults to a USB PC Keyboard. Refer to page 2-2 for other USB
terminal settings.
Connecting with Keyboard Wedge

A scanner can be connected between the keyboard and PC as a “keyboard
wedge,” where the scanner provides data output that is similar to keyboard
entries. The following is an example of a keyboard wedge connection:
1. Turn off power and disconnect the keyboard cable from the back of the
terminal/computer.
2. Connect the appropriate interface cable to the device and to the
terminal/computer.
3. Turn the terminal/computer power back on. The scanner beeps.

4. Verify the scanner operation by scanning a bar code from the Sample
Symbols in the back of this manual. The scanner beeps once.
The unit defaults to an IBM PC AT and compatibles keyboard wedge inter-
face with a USA keyboard. A carriage return (CR) suffix is added to bar
code data.
1-2
Reading Techniques
The scanner has a view finder that projects a bright red aiming beam that corre-
sponds to the scanner’s horizontal field of view. The aiming beam should be
centered over the bar code, but it can be positioned in any direction for a good
read.
Linear bar code 2D Matrix symbol
The aiming beam or pattern is smaller when the scanner is closer to the code
and larger when it is farther from the code. Symbologies with smaller bars or
elements (mil size) should be read closer to the unit. Symbologies with larger
bars or elements (mil size) should be read farther from the unit. To read single
or multiple symbols (on a page or on an object), hold the scanner at an appro-
priate distance from the target, press the button, and center the aiming beam or
pattern on the symbol. If the code being scanned is highly reflective (e.g., lami-
nated), it may be necessary to tilt the code up 15° to 18° to prevent unwanted
reflection.
Menu Bar Code Security Settings

Youjie scanners are programmed by scanning menu bar codes or by sending
serial commands to the scanner. If you want to restrict the ability to scan menu
codes, you can use the Menu Bar Code Security settings. Please contact the
nearest technical support office (see Customer Support on page 11-1) for fur-
ther information.
1-3
Setting Custom Defaults
You have the ability to create a set of menu commands as your own, custom
defaults. To do so, scan the Set Custom Defaults bar code below before
scannning the menu commands for your custom defaults. If a menu command
requires scanning numeric codes from the back cover, then a Save code, that
entire sequence will be saved to your custom defaults. When you have entered
all the commands you want to save for your custom defaults, scan the Save
Custom Defaults bar code.
Set Custom Defaults
Save Custom Defaults

You may have a series of custom settings and want to correct a single setting.
To do so, just scan the new setting to overwrite the old one. For example, if you
had previously saved the setting for Beeper Volume at Low to your custom
defaults, and decide you want the beeper volume set to High, just scan the Set
Custom Defaults bar code, then scan the Beeper Volume High menu code,
and then Save Custom Defaults. The rest of the custom defaults will remain,
but the beeper volume setting will be updated.
Resetting the Custom Defaults

If you want the custom default settings restored to your scanner, scan the Acti-
vate Custom Defaults bar code below. This is the recommended default bar
code for most users. It resets the scanner to the custom default settings. If
there are no custom defaults, it will reset the scanner to the factory default set-
tings. Any settings that have not been specified through the custom defaults
will be defaulted to the factory default settings.
Activate Custom Defaults
1-4
Resetting the Factory Defaults
This selection erases all your settings and resets the scanner to the
! original factory defaults. It also disables all plugins.
If you aren’t sure what programming options are in your scanner, or you’ve
changed some options and want to restore the scanner to factory default set-
tings, first scan the Remove Custom Defaults bar code, then scan Activate
Defaults. This resets the scanner to the factory default settings.
Remove Custom Defaults
Activate Defaults
1-5
1-6
2
Programming the Interface
Introduction
This chapter describes how to program your system for the desired interface.
Programming the Interface - Plug and Play

Plug and Play bar codes provide instant scanner set up for commonly used
interfaces.
Note: After you scan one of the codes, power cycle the host terminal to have
the interface in effect.
Keyboard Wedge
If you want your system programmed for an IBM PC AT and compatibles key-
board wedge interface with a USA keyboard, scan the bar code below. Key-
board wedge is the default interface.
Note: The following bar code also programs a carriage return (CR) suffix.
IBM PC AT and Compatibles with

CR suffix
Laptop Direct Connect

For most laptops, scanning the Laptop Direct Connect bar code allows opera-
tion of the scanner in parallel with the integral keyboard. The following Laptop
Direct Connect bar code also programs a carriage return (CR) suffix and turns
on Emulate External Keyboard (page 2-12).
Laptop Direct Connect

with CR suffix
2-1
USB IBM SurePos
Scan one of the following “Plug and Play” codes to program the scanner for an
IBM SurePos (USB handheld scanner) or IBM SurePos (USB tabletop scanner)
interface.
Note: After scanning one of these codes, you must power cycle the cash
register.
USB IBM SurePos

(USB Handheld Scanner)
Interface
USB IBM SurePos

(USB Tabletop Scanner)
Interface
Each bar code above also programs the following suffixes for each symbology:
Symbology Suffix Symbology Suffix

EAN 8 0C Code 39 00 0A 0B
EAN 13 16 Interleaved 2 of 5 00 0D 0B
UPC A 0D Code 128 00 18 0B
UPC E 0A Code 39 00 0A 0B
USB PC or Macintosh Keyboard

Scan one of the following codes to program the scanner for USB PC Keyboard
or USB Macintosh Keyboard. Scanning these codes also adds a CR and LF.
USB Keyboard (PC)
USB Keyboard (Mac)
USB Japanese Keyboard (PC)
2-2
USB HID
Scan the following code to program the scanner for USB HID bar code scan-
ners.
USB HID Bar Code Scanner
2-3
Keyboard Country Layout
Scan the appropriate country code below to program the keyboard layout for
your country or language. As a general rule, the following characters are sup-
ported, but need special care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
* United States
United States (Dvorak)
United States (Dvorak left)
United States (Dvorak right)
United States (International)
Albania
Azeri (Cyrillic)
Azeri (Latin)
Belarus
Belgium
Bosnia
Brazil
2-4
Keyboard Country (continued)
Brazil (MS)
Bulgaria (Cyrillic)
Bulgaria (Latin)
Canada (French legacy)
Canada (French)
Canada (Multilingual)
Croatia
Czech
Czech (Programmers)
Czech (QWERTY)
Czech (QWERTZ)
Denmark
Dutch (Netherlands)
2-5
Estonia
Faeroese
Finland
France
Gaelic
Germany
Greek
Greek (220 Latin)
Greek (220)
Greek (319 Latin)
Greek (319)
Greek (Latin)
Greek (MS)
2-6
Greek (Polytonic)
Hebrew
Hungarian (101 key)
Hungary
Iceland
Irish
Italian (142)
Italy
Japan ASCII
Kazakh
Kyrgyz (Cyrillic)
Latin America
Latvia
2-7
Latvia (QWERTY)
Lithuania
Lithuania (IBM)
Macedonia
Malta
Mongolian (Cyrillic)
Norway
Poland
Polish (214)
Polish (Programmers)
Portugal
Romania
Russia
2-8
Russian (MS)
Russian (Typewriter)
SCS
Serbia (Cyrillic)
Serbia (Latin)
Slovakia
Slovakia (QWERTY)
Slovakia (QWERTZ)
Slovenia
Spain
Spanish variation
Sweden
Switzerland (French)
2-9
Switzerland (German)
Tatar
Turkey F
Turkey Q
Ukrainian
United Kingdom
United Stated (Dvorak right)
United States (Dvorak left)
United States (Dvorak)
United States (International)
Uzbek (Cyrillic)
Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock. If you have
used Keyboard Conversion settings, they will override any of the following Key-
board Style settings. Default = Regular.
2 - 10
Regular is used when you normally have the Caps Lock key off.
* Regular
Caps Lock is used when you normally have the Caps Lock key on.
Caps Lock
Shift Lock is used when you normally have the Shift Lock key on (not common
to U.S. keyboards).
Shift Lock
Automatic Caps Lock is used if you change the Caps Lock key on and off.
The software tracks and reflects if you have Caps Lock on or off . This selection
can only be used with systems that have an LED that notes the Caps Lock sta-
tus (AT keyboards).
Automatic Caps Lock
Autocaps via NumLock bar code should be scanned in countries (e.g., Ger-
many, France) where the Caps Lock key cannot be used to toggle Caps Lock.
The NumLock option works similarly to the regular Autocaps, but uses the Num-
Lock key to retrieve the current state of the Caps Lock.
Autocaps via NumLock
2 - 11
Emulate External Keyboard should be scanned if you do not have an external
keyboard (IBM AT or equivalent).
Emulate External Keyboard
Note: After scanning the Emulate External Keyboard bar code, you must power
cycle your computer.
Keyboard Conversion
Alphabetic keyboard characters can be forced to be all upper case or all lower-
case. So if you have the following bar code: “abc569GK,” you can make the
output “ABC569GK” by scanning Convert All Characters to Upper Case, or to
“abc569gk” by scanning Convert All Characters to Lower Case.
These settings override Keyboard Style selections.
Note: If your interface is a keyboard wedge, first scan the menu code for
Automatic Caps Lock (page 2-11). Otherwise, your output may not be as
expected.
Default = Keyboard Conversion Off.
* Keyboard Conversion Off
Convert All Characters

to Upper Case
Convert All Characters

to Lower Case
Control Character Output

This selection sends a text string instead of a control character. For example,
when the control character for a carriage return is expected, the output would
display [CR] instead of the ASCII code of 0D. Refer to ASCII Conversion Chart
(Code Page 1252) on page A-4. Only codes 00 through 1F are converted (the
first column of the chart).
Note: Control + ASCII Mode overrides this mode.
2 - 12
Default = Off.
Control Character Output On
* Control Character Output Off
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes and
Turbo Mode.
Control + ASCII Mode On: The scanner sends key combinations for ASCII
control characters for values 00-1F. Windows is the preferred mode. All key-
board country codes are supported. DOS mode is a legacy mode, and it does
not support all keyboard country codes. New users should use the Windows
mode. Refer to Keyboard Function Relationships, page 7-1 for CTRL+ ASCII
Values.
Windows Mode Prefix/Suffix Off: The scanner sends key combinations for
ASCII control characters for values 00-1F, but it does not transmit any prefix or
suffix information.
Default = Control + ASCII Mode Off.
Windows Mode Control + ASCII

Mode On
* Control + ASCII Mode Off
DOS Mode Control + ASCII Mode

On
Windows Mode Prefix/Suffix Off
2 - 13
Turbo Mode: The scanner sends characters to a terminal faster. If the termi-
nal drops characters, do not use Turbo Mode. Default = Off
Turbo Mode On
* Turbo Mode Off
Numeric Keypad Mode: Sends numeric characters as if entered from a

numeric keypad. Default = Off
Numeric Keypad Mode On
* Numeric Keypad Mode Off
Automatic Direct Connect Mode: This selection can be used if you have an
IBM AT style terminal and the system is dropping characters. Default = Off
Automatic Direct Connect Mode

On
* Automatic Direct Connect

Mode Off
2 - 14
3
Input/Output Settings
Power Up Beeper
The scanner can be programmed to beep when it’s powered up. Scan the Off
bar code(s) if you don’t want a power up beep. Default = Power Up Beeper On
- Scanner.
Power Up Beeper Off -

Scanner
* Power Up Beeper On -
Scanner
Trigger Click
To hear an audible click every time the scanner button is pressed, scan the Trig-
ger Click On bar code below. Scan the Trigger Click Off code if you don’t
wish to hear the click. (This feature has no effect on serial or automatic trigger-
ing.) Default = Trigger Click Off.
*Trigger Click Off
Trigger Click On
3-1
Good Read and Error Indicators
Beeper – Good Read
The beeper may be programmed On or Off in response to a good read.
Turning this option off, only turns off the beeper response to a good read
indication. All error and menu beeps are still audible. Default = Beeper -
Good Read On.
Beeper - Good Read Off
* Beeper - Good Read On
Beeper Volume – Good Read

The beeper volume codes modify the volume of the beep the scanner
emits on a good read. Default = High.
Low
Medium
* High
Off
3-2
Beeper Pitch – Good Read
The beeper pitch codes modify the pitch (frequency) of the beep the scan-
ner emits on a good read. Default = Medium.
Low (1600 Hz)
* Medium (2400 Hz)
High (4200 Hz)
Beeper Pitch – Error

The beeper pitch codes modify the pitch (frequency) of the sound the scan-
ner emits when there is a bad read or error. Default = Razz.
* Razz (250 Hz)
Medium (3250 Hz)
High (4200 Hz)
Beeper Duration – Good Read

The beeper duration codes modify the length of the beep the scanner emits
on a good read. Default = Normal.
* Normal Beep
Short Beep
3-3
LED – Good Read
The LED indicator can be programmed On or Off in response to a good
read. Default = On.
* LED - Good Read On
LED - Good Read Off
Number of Beeps – Good Read

The number of beeps of a good read can be programmed from 1 - 9. The
same number of beeps will be applied to the beeper and LED in response
to a good read. For example, if you program this option to have five beeps,
there will be five beeps and five LED flashes in response to a good read.
The beeps and LED flashes are in sync with one another. To change the
number of beeps, scan the bar code below and then scan a digit (1-9) bar
code and the Save bar code on the Programming Chart inside the back
cover of this manual. Default = 1.
Number of Good Read Beeps/LED Flashes
Number of Beeps – Error

The number of beeps and LED flashes emitted by the scanner for a bad
read or error can be programmed from 1 - 9. For example, if you program
this option to have five error beeps, there will be five error beeps and five
LED flashes in response to an error. To change the number of error beeps,
scan the bar code below and then scan a digit (1-9) bar code and the Save
bar code on the Programming Chart inside the back cover of this manual.
Default = 1.
Number of Error Beeps/LED Flashes
3-4
Good Read Delay
This sets the minimum amount of time before the scanner can read another
bar code. Default = 0 ms (No Delay).
* No Delay
Short Delay (500 ms)
Medium Delay (1,000 ms)
Long Delay (1,500 ms)
User-Specified Good Read Delay

If you want to set your own length for the good read delay, scan the bar
code below, then set the delay (from 0-30,000 milliseconds) by scanning
digits from the inside back cover, then scanning Save.
User-Specified Good Read Delay
Manual Trigger Mode

When in manual trigger mode, the scanner scans until a bar code is read, or
until the button is released. Default = Manual Trigger-Normal.
* Manual Trigger - Normal
3-5
Presentation Mode
Presentation Mode uses ambient light to detect bar codes. The LED dims until
a bar code is presented to the scanner, then the LED brightens to read the
code. If the light level in the room is not high enough, Presentation Mode may
not work properly.
Presentation Mode
Presentation Sensitivity
Presentation Sensitivity is a numeric range that increases or decreases the
scanner's reaction time to bar code presentation. To set the sensitivity,
scan the Sensitivity bar code, then scan the degree of sensitivity (from 0-
20) from the inside back cover, and Save. 0 is the most sensitive setting,
and 20 is the least sensitive. Default = 1.
Sensitivity
Presentation Centering
Use Presentation Centering to narrow the scanner’s field of view when it is
in the stand to make sure the scanner reads only those bar codes intended
by the user. For instance, if multiple codes are placed closely together,
Presentation Centering will insure that only the desired codes are read.
Note: To adjust centering when the scanner is hand-held, see
Centering (page 3-10).
If a bar code is not touched by a predefined window, it will not be decoded
or output by the scanner. If Presentation Centering is turned on by scan-
ning Presentation Centering On, the scanner only reads codes that pass
through the centering window you specify using the Top of Presentation
Centering Window, Bottom of Presentation Centering Window, Left,
and Right of Presentation Centering Window bar codes.
3-6
In the example below, the white box is the centering window. The centering
window has been set to 20% left, 30% right, 8% top, and 25% bottom.
Since Bar Code 1 passes through the centering window, it will be read. Bar
Code 2 does not pass through the centering window, so it will not be read.
0%
Bar Code 1
10
20 Bar Code 2
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90 100%
Note: A bar code needs only to be touched by the centering window in

order to be read. It does not need to pass completely through the
centering window.
3-7
Scan Presentation Centering On, then scan one of the following bar codes to
change the top, bottom, left, or right of the centering window. Then scan the
percent you want to shift the centering window using digits on the inside back
cover of this manual. Scan Save. Default Presentation Centering = 40% for
Top and Left, 60% for Bottom and Right.
Presentation Centering On
* Presentation Centering Off
Top of Presentation Centering

Window
Bottom of Presentation
Centering Window
Left of
Presentation Centering
Window
Right of Presentation Centering

Window
Mobile Phone Read Mode

When this mode is selected, your scanner is optimized to read bar codes from
mobile phone or other LED displays. However, the speed of scanning printed
bar codes may be slightly lower when this mode is enabled.
Hand Held Scanning - Mobile

Phone
Presentation Scanning -
Mobile Phone
Note: To turn off Mobil Phone Read Mode, scan the Manual Trigger Mode bar
code (see page 3-5).
3-8
Hands Free Time-Out
The Scan Stand and Presentation Modes are referred to as “hands free”
modes. If the scanner’s button is pressed when using a hands free mode, the
scanner changes to manual trigger mode. You can set the time the scanner
should remain in manual trigger mode by setting the Hands Free Time-Out.
Once the time-out value is reached, (if there have been no further button
presses) the scanner reverts to the original hands free mode.
Scan the Hands Free Time-Out bar code, then scan the time-out duration
(from 0-300,000 milliseconds) from the inside back cover, and Save. Default =
5,000 ms.
Hands Free Time-Out
Reread Delay
This sets the time period before the scanner can read the same bar code a sec-
ond time. Setting a reread delay protects against accidental rereads of the
same bar code. Longer delays are effective in minimizing accidental rereads.
Use shorter delays in applications where repetitive bar code scanning is
required. Reread Delay only works when in Presentation Mode (see page 3-6).
Default = Medium.
Short (500 ms)
* Medium (750 ms)
Long (1000 ms)
Extra Long (2000 ms)
3-9
User-Specified Reread Delay
If you want to set your own length for the reread delay, scan the bar code below,
then set the delay (from 0-30,000 milliseconds) by scanning digits from the
inside back cover, then scanning Save.
User-Specified Reread Delay
Scanner Time-Out
Scanner Time-Out powers down the scanner after the unit has been idle for the
specified time. To prevent the scanner from powering down, set this time-out to
0, or no timer. Scan Scanner Time-Out, then set the time-out by scanning dig-
its (from 0 - 999,999 ms) from the inside back cover, then scanning Save.
Default = 1 ms.
Scanner Time-Out
Centering
Use Centering to narrow the scanner’s field of view to make sure that when the
scanner is hand-held, it reads only those bar codes intended by the user. For
instance, if multiple codes are placed closely together, centering will insure that
only the desired codes are read.
Note: To adjust centering when the scanner is in the stand, see Presentation
Centering (page 3-6).
If a bar code is not touched by a predefined window, it will not be decoded or
output by the scanner. If centering is turned on by scanning Centering On, the
scanner only reads codes that pass through the centering window you specify
using the Top of Centering Window, Bottom of Centering Window, Left, and
Right of Centering Window bar codes.
3 - 10
In the example below, the white box is the centering window. The centering win-
dow has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Bar
Code 1 passes through the centering window, it will be read. Bar Code 2 does
not pass through the centering window, so it will not be read.
0%
Bar Code 1
10
20 Bar Code 2
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90 100%
Note: A bar code needs only to be touched by the centering window in order to
be read. It does not need to pass completely through the centering
window.
3 - 11
Scan Centering On, then scan one of the following bar codes to change the
top, bottom, left, or right of the centering window. Then scan the percent you
want to shift the centering window using digits on the inside back cover of this
manual. Scan Save. Default Centering = 40% for Top and Left, 60% for Bot-
tom and Right.
Centering On
* Centering Off
Top of Centering Window
Bottom of Centering Window
Left of Centering Window
Right of Centering Window
No Read
With No Read turned On, the scanner notifies you if a code cannot be read.
Default = Off.
On
* Off
If you want a different notation than “NR,” for example, “Error,” or “Bad Code,”
you can edit the output message (see Data Formatting beginning on page 5-1).
The hex code for the No Read symbol is 9C.
3 - 12
Video Reverse
Video Reverse is used to allow the scanner to read bar codes that are inverted.
The Video Reverse Off bar code below is an example of this type of bar code.
Scan Video Reverse Only to read only inverted bar codes. Scan Video
Reverse and Standard Bar Codes to read both types of codes.
Note: After scanning Video Reverse Only, menu bar codes cannot be read.
You must scan Video Reverse Off or Video Reverse and Standard Bar
Codes in order to read menu bar codes.
Note: Images downloaded from the unit are not reversed. This is a setting for
decoding only.
Video Reverse Only
Video Reverse and Standard Bar

Codes
VIDREV0.
* Video Reverse Off
3 - 13
Working Orientation
Some bar codes are direction-sensitive. For example, KIX codes and OCR can
misread when scanned sideways or upside down. Use the working orientation
settings if your direction-sensitive codes will not usually be presented upright to
the scanner. Default = Upright.
Upright:
Vertical, Top to Bottom:

(Rotate CW 90°)
Upside Down:
Vertical, Bottom to Top:

(Rotate CCW 90°)
Default = Upright.
* Upright
Vertical, Bottom to Top
Upside Down
Vertical, Top to Bottom
3 - 14
4
Data Editing
Prefix/Suffix Overview
When a bar code is scanned, additional information is sent to the host computer
along with the bar code data. This group of bar code data and additional,
user-defined data is called a “message string.” The selections in this section
are used to build the user-defined data into the message string.
Prefix and Suffix characters are data characters that can be sent before and
after scanned data. You can specify if they should be sent with all symbologies,
or only with specific symbologies. The following illustration shows the break-
down of a message string:
Prefix Scanned Data Suffix

1-11 variable length 1-11
alpha numeric & alpha numeric &
control characters control characters
Points to Keep In Mind

• It is not necessary to build a message string. The selections in this
chapter are only used if you wish to alter the default settings. Default
prefix = None. Default suffix = None.
• A prefix or suffix may be added or cleared from one symbology or all
symbologies.
• You can add any prefix or suffix from the ASCII Conversion Chart (Code
Page 1252), beginning on page A-4, plus Code I.D. and AIM I.D.
• You can string together several entries for several symbologies at one
time.
• Enter prefixes and suffixes in the order in which you want them to appear
on the output.
• When setting up for specific symbologies (as opposed to all
symbologies), the specific symbology ID value counts as an added prefix
or suffix character.
• The maximum size of a prefix or suffix configuration is 200 characters,
which includes header information.
To Add a Prefix or Suffix:

Step 1. Scan the Add Prefix or Add Suffix symbol (page 4-3).
Step 2. Determine the 2 digit Hex value from the Symbology Chart
(included in the Symbology Chart, beginning on page A-1) for the
4-1
symbology to which you want to apply the prefix or suffix. For
example, for Code 128, Code ID is “j” and Hex ID is “6A”.
Step 3. Scan the 2 hex digits from the Programming Chart inside the back
cover of this manual or scan 9, 9 for all symbologies.
Step 4. Determine the hex value from the ASCII Conversion Chart (Code
Page 1252), beginning on page A-4, for the prefix or suffix you wish
to enter.
Step 5. Scan the 2 digit hex value from the Programming Chart inside the
back cover of this manual.
Step 6. Repeat Steps 4 and 5 for every prefix or suffix character.
Step 7. To add the Code I.D., scan 5, C, 8, 0.
To add AIM I.D., scan 5, C, 8, 1.
To add a backslash (\), scan 5, C, 5, C.
Note: To add a backslash (\) as in Step 7, you must scan 5C twice – once
to create the leading backslash and then to create the backslash
itself.
Step 8. Scan Save to exit and save, or scan Discard to exit without saving.
Repeat Steps 1-6 to add a prefix or suffix for another symbology.
Example: Add a Suffix to a specific symbology

To send a CR (carriage return)Suffix for U.P.C. only:
Step 1. Scan Add Suffix.
Step 2. Determine the 2 digit hex value from the Symbology Chart
(included in the Symbology Chart, beginning on page A-1) for
U.P.C..
Step 3. Scan 6, 3 from the Programming Chart inside the back cover of this
manual.
Step 4. Determine the hex value from the ASCII Conversion Chart (Code
Page 1252), beginning on page A-4, for the CR (carriage return).
Step 5. Scan 0, D from the Programming Chart inside the back cover of this
manual.
Step 6. Scan Save, or scan Discard to exit without saving.
To Clear One or All Prefixes or Suffixes

You can clear a single prefix or suffix, or clear all prefixes/suffixes for a
symbology. If you have been entering prefixes and suffixes for single sym-
bologies, you can use Clear One Prefix (Suffix) to delete a specific char-
acter from a symbology. When you Clear All Prefixes (Suffixes), all the
prefixes or suffixes for a symbology are deleted.
4-2
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol.
Step 2. Determine the 2 digit Hex value from the Symbology Chart
(included in the Symbology Chart, beginning on page A-1) for the
symbology from which you want to clear the prefix or suffix.
Step 3. Scan the 2 digit hex value from the Programming Chart inside the
back cover of this manual or scan 9, 9 for all symbologies.
Your change is automatically saved.
To Add a Carriage Return Suffix to All Symbologies

Scan the following bar code if you wish to add a carriage return suffix to all
symbologies at once. This action first clears all current suffixes, then pro-
grams a carriage return suffix for all symbologies.
Add CR Suffix
All Symbologies
Prefix Selections
Add Prefix
Clear One Prefix
Clear All Prefixes
4-3
Suffix Selections
Add Suffix
Clear One Suffix
Clear All Suffixes
Function Code Transmit

When this selection is enabled and function codes are contained within the
scanned data, the scanner transmits the function code to the terminal. Charts
of these function codes are provided in Supported Interface Keys starting on
page 7-3. When the scanner is in keyboard wedge mode, the scan code is con-
verted to a key code before it is transmitted. Default = Enable.
* Enable
Disable
Intercharacter, Interfunction, and

Intermessage Delays
Some terminals drop information (characters) if data comes through too quickly.
Intercharacter, interfunction, and intermessage delays slow the transmission of
data, increasing data integrity.
4-4
Intercharacter Delay
An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may
be placed between the transmission of each character of scanned data.
Scan the Intercharacter Delay bar code below, then scan the number of
5ms delays, and the Save bar code using the Programming Chart inside
the back cover of this manual.
1 2 3 4 5
To remove this delay, scan the Intercharacter Delay bar code, then set the
number of delays to 0. Scan the Save bar code using the Programming
Chart inside the back cover of this manual.
Note: Intercharacter delays are not supported in USB serial emulation.
User Specified Intercharacter Delay

An intercharacter delay of up to 5000 milliseconds (in 5ms increments)
may be placed after the transmission of a particular character of scanned
data. Scan the Delay Length bar code below, then scan the number of
5ms delays, and the Save bar code using the Programming Chart inside
the back cover of this manual.
Next, scan the Character to Trigger Delay bar code, then the 2-digit hex
value for the ASCII character that will trigger the delay ASCII Conversion
Chart (Code Page 1252), beginning on page A-4.
Delay Length
Character to Trigger Delay

To remove this delay, scan the Delay Length bar code, and set the number
of delays to 0. Scan the Save bar code using the Programming Chart
inside the back cover of this manual.
4-5
Interfunction Delay
An interfunction delay of up to 5000 milliseconds (in 5ms increments) may
be placed between the transmission of each segment of the message
string. Scan the Interfunction Delay bar code below, then scan the num-
ber of 5ms delays, and the Save bar code using the Programming Chart
STX 1 HT 2 3 4 5 CR LF
Interfunction Delays
Interfunction Delay
To remove this delay, scan the Interfunction Delay bar code, then set the
Intermessage Delay
An intermessage delay of up to 5000 milliseconds (in 5ms increments)
may be placed between each scan transmission. Scan the Intermessage
Delay bar code below, then scan the number of 5ms delays, and the Save
bar code using the Programming Chart inside the back cover of this man-
ual.
1st Scan Transmission 2nd Scan Transmission

Intermessage Delay
Intermessage Delay
To remove this delay, scan the Intermessage Delay bar code, then set the
4-6
5
Data Formatting
Data Format Editor Introduction

You may use the Data Format Editor to change the scanner’s output. For exam-
ple, you can use the Data Format Editor to insert characters at certain points in
bar code data as it is scanned. The selections in the following pages are used
only if you wish to alter the output. Default Data Format setting = None.
Normally, when you scan a bar code, it gets outputted automatically; however
when you create a format, you must use a “send” command (see Send
Commands on page 5-4) within the format program to output data.
Multiple formats may be programmed into the scanner. They are stacked in the
order in which they are entered. However, the following list presents the order
in which formats are applied:
1. Specific Terminal ID, Actual Code ID, Actual Length
2. Specific Terminal ID, Actual Code ID, Universal Length
3. Specific Terminal ID, Universal Code ID, Actual Length
4. Specific Terminal ID, Universal Code ID, Universal Length
5. Universal Terminal ID, Actual Code ID, Actual Length
6. Universal Terminal ID, Actual Code ID, Universal Length
7. Universal Terminal ID, Universal Code ID, Actual Length
8. Universal Terminal ID, Universal Code ID, Universal Length
The maximum size of a data format configuration is 2000 bytes, which includes
header information.
If you have changed data format settings, and wish to clear all formats and
return to the factory defaults, scan the Default Data Format code below.
* Default Data Format
Add a Data Format

Step 1. Scan the Enter Data Format symbol (page 5-2).
Step 2. Select Primary/Alternate Format
Determine if this will be your primary data format, or one of 3 alternate
formats. This allows you to save a total of 4 different data formats. To
program your primary format, scan 0 using the Programming Chart
inside the back cover of this manual. If you are programming an
alternate format, scan 1, 2, or 3, depending on which alternate format
5-1
you are programming. (See Primary/Alternate Data Formats on page
5-8 for further information.)
Step 3. Terminal Type
Refer to Terminal ID Table (page 5-4) and locate the Terminal ID
number for your PC. Scan three numeric bar codes on the inside back
cover to program the scanner for your terminal ID (you must enter 3
digits). For example, scan 0 0 3 for an AT wedge.
Note: The wildcard for all terminal types is 099.
Step 4. Code I.D.
In the Symbology Chart, beginning on page A-1, find the symbology to
which you want to apply the data format. Locate the Hex value for that
symbology and scan the 2 digit hex value from the Programming Chart
Note: If you are creating a data format for Batch Mode Quantity, use 35
for the Code I.D.
Step 5. Length
Specify what length (up to 9999 characters) of data will be acceptable
for this symbology. Scan the four digit data length from the
Programming Chart inside the back cover of this manual. (Note: 50
characters is entered as 0050. 9999 is a universal number, indicating
all lengths.)
Step 6. Editor Commands
Refer to Data Format Editor Commands (page 5-4). Scan the symbols
that represent the command you want to enter. 94 alphanumeric
characters may be entered for each symbology data format.
Step 7. Scan Save to save your data format, or Discard to exit without saving
your changes.
Enter Data Format
Save
Discard
5-2
Other Programming Selections
Clear One Data Format
This deletes one data format for one symbology. If you are clearing the
primary format, scan 0 from the Programming Chart inside the back
cover of this manual. If you are clearing an alternate format, scan 1, 2,
or 3, depending on the format you are clearing. Scan the Terminal Type
and Code I.D. (see Symbology Chart on page A-1), and the bar code
data length for the specific data format that you want to delete. All other
formats remain unaffected.
Clear all Data Formats
This clears all data formats.
Save to exit and save your data format changes.
Discard to exit without saving any data format changes.
Clear One Data Format
Clear All Data Formats
Save
Discard
5-3
Terminal ID Table
Terminal
Terminal Model(s)
ID
IBM PC/AT and compatibles 003
USB SurePOS Handheld 128
Scanner
USB SurePOS Tabletop 129
Scanner
USB PC Keyboard 124
Mac Keyboard 125
Japanese Keyboard (PC) 134
HID POS 131
Data Format Editor Commands

Send Commands
Send all characters
F1 Include in the output message all of the characters from the input
message, starting from current cursor position, followed by an insert
character. Syntax = F1xx where xx stands for the insert character’s hex
value for its ASCII code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on
page A-4 for decimal, hex and character codes.
Send a number of characters
F2 Include in the output message a number of characters followed by an
insert character. Start from the current cursor position and continue for
“nn” characters or through the last character in the input message,
followed by character “xx.” Syntax = F2nnxx where nn stands for the
numeric value (00-99) for the number of characters, and xx stands for
the the insert character’s hex value for its ASCII code.
Send all characters up to a particular character
F3 Include in the output message all characters from the input message,
starting with the character at the current cursor position and continuing
to, but not including, the search character “ss,” followed by an insert
character. The cursor is moved forward to the “ss” character. Syntax
= F3ssxx where ss stands for the search character’s hex value for its
ASCII code, and xx stands for the insert character’s hex value for its
ASCII code.
5-4
Send all but the last characters
E9 Include in the output message all but the last “nn” characters, starting
from the current cursor position. The cursor is moved forward to one
position past the last input message character included. Syntax = E9nn
where nn stands for the numeric value (00-99) for the number of
characters that will not be sent at the end of the message.
Insert a character multiple times
F4 Send “xx” character “nn” times in the output message, leaving the
cursor in the current position. Syntax = F4xxnn where xx stands for the
insert character’s hex value for its ASCII code, and nn is the numeric
value (00-99) for the number of times it should be sent.
Move Commands
Move the cursor forward a number of characters
F5 Move the cursor ahead “nn” characters from current cursor position.
Syntax = F5nn where nn is the numeric value (00-99) for the number
of characters the cursor should be moved ahead.
Move the cursor backward a number of characters
F6 Move the cursor back “nn” characters from current cursor position.
Syntax = F6nn where nn is the numeric value (00-99) for the number
of characters the cursor should be moved back.
Move the cursor to the beginning
F7 Move the cursor to the first character in the input message. Syntax =
F7.
Move the cursor to the end
EA Move the cursor to the last character in the input message. Syntax =
EA.
Search Commands
Search forward for a character
F8 Search the input message forward for “xx” character from the current
cursor position, leaving the cursor pointing to the “xx” character. Syntax
= F8xx where xx stands for the search character’s hex value for its
ASCII code.
5-5
Search backward for a character
F9 Search the input message backward for “xx” character from the current
cursor position, leaving the cursor pointing to the “xx” character.
Syntax = F9xx where xx stands for the search character’s hex value for
its ASCII code.
Search forward for a non-matching character
E6 Search the input message forward for the first non-“xx” character from
the current cursor position, leaving the cursor pointing to the non-“xx”
character. Syntax = E6xx where xx stands for the search character’s
hex value for its ASCII code.
Search backward for a non-matching character
E7 Search the input message backward for the first non-“xx” character
from the current cursor position, leaving the cursor pointing to the non-
“xx” character. Syntax = E7xx where xx stands for the search
character’s hex value for its ASCII code.
Miscellaneous Commands
Suppress characters
FB Suppress all occurrences of up to 15 different characters, starting at the
current cursor position, as the cursor is advanced by other commands.
When the FC command is encountered, the suppress function is
terminated. The cursor is not moved by the FB command.
Syntax = FBnnxxyy . .zz where nn is a count of the number of
suppressed characters in the list, and xxyy .. zz is the list of characters
to be suppressed.
Stop suppressing characters
FC Disables suppress filter and clear all suppressed characters. Syntax =
FC.
Replace characters
E4 Replaces up to 15 characters in the output message, without moving
the cursor. Replacement continues until the E5 command is
encountered. Syntax = E4nnxx1xx2yy1yy2...zz1zz2 where nn is the
total count of of the number of characters in the list (characters to be
replaced plus replacement characters); xx1 defines characters to be
replaced and xx2 defines replacement characters, continuing through
zz1 and zz2.
5-6
Stop replacing characters
E5 Terminates character replacement. Syntax = E5.
Compare characters
FE Compare the character in the current cursor position to the character
“xx.” If characters are equal, move the cursor forward one position.
Syntax = FExx where xx stands for the comparison character’s hex
value for its ASCII code.
Check for a number
EC Check to make sure there is an ASCII number at the current cursor
position. The format is aborted if the character is not numeric.
Check for non-numeric character
ED Check to make sure there is a non-numeric ASCII character at the
current cursor position. The format is aborted if the character is
numeric.
Insert a delay
EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting
from the current cursor position. Syntax = EFnnnn where nnnn stands
for the delay in 5ms increments, up to 9999. This command can only
be used with keyboard emulation.
Data Formatter
When Data Formatter is turned Off, the bar code data is output to the host as
read, including prefixes and suffixes.
Data Formatter Off
You may wish to require the data to conform to a data format you have created
and saved. The following settings can be applied to your data format:
Data Formatter On, Not Required, Keep Prefix/Suffix
Scanned data is modified according to your data format, and prefixes and
suffixes are transmitted.
Data Format Required, Keep Prefix/Suffix
Scanned data is modified according to your data format, and prefixes and
suffixes are transmitted. Any data that does not match your data format
requirements generates an error tone and the data in that bar code is not
transmitted.
5-7
Default = Data Formatter On, Not Required, Keep Prefix/Suffix.
* Data Formatter On,

Not Required,
Keep Prefix/Suffix
Data Format Required,

Keep Prefix/Suffix
Primary/Alternate Data Formats

You can save up to four data formats, and switch between these formats. Your
primary data format is saved under 0. Your other three formats are saved under
1, 2, and 3. To set your device to use one of these formats, scan one of the bar
codes below.
Primary Data Format
Data Format 1
Data Format 2
Data Format 3
5-8
6
Symbologies
This programming section contains the following menu selections.
• All Symbologies • Interleaved 2 of 5

• Aztec Code • Korea Post
• China Post (Hong Kong 2 of 5) • Matrix 2 of 5
• Chinese Sensible (Han Xin) Code • MicroPDF417
• Codabar • MSI
• Codablock A • NEC 2 of 5
• Codablock F • Postal Codes - Linear
• Code 128 • PDF417
• Code 39 • GS1 DataBar Omnidirectional
• Code 93 • QR Code
• Straight 2 of 5 IATA (two-bar start/
• Data Matrix stop)
• Straight 2 of 5 Industrial (three-bar
• EAN/JAN-13
start/stop)
• EAN/JAN-8 • TCIF Linked Code 39 (TLC39)
• GS1 Composite Codes
• GS1 DataBar Expanded • UPC-A
• UPC-A/EAN-13 with Extended
• GS1 DataBar Limited
Coupon Code
• GS1 DataBar Omnidirectional • UPC-E0
• GS1 Emulation • UPC-E1
• GS1-128
6-1
All Symbologies
If you want to decode all the symbologies allowable for your scanner, scan the
All Symbologies On code. If on the other hand, you want to decode only a
particular symbology, scan All Symbologies Off followed by the On symbol for
that particular symbology.
All Symbologies On
All Symbologies Off
Note: When All Symbologies On is scanned, 2D Postal Codes are not enabled.
2D Postal Codes must be enabled separately.
Message Length Description

You are able to set the valid reading length of some of the bar code symbolo-
gies. If the data length of the scanned bar code doesn’t match the valid read-
ing length, the scanner will issue an error tone. You may wish to set the same
value for minimum and maximum length to force the scanner to read fixed
length bar code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15Max. length = 15
For a value other than the minimum and maximum message length defaults,
scan the bar codes included in the explanation of the symbology, then scan the
digit value of the message length and Save bar codes on the Programming
Chart inside the back cover of this manual. The minimum and maximum
lengths and the defaults are included with the respective symbologies.
6-2
Codabar
<Default All Codabar Settings>
Codabar On/Off
* On
Off
Codabar Start/Stop Characters

Start/Stop characters identify the leading and trailing ends of the bar code.
You may either transmit, or not transmit Start/Stop characters.
Default = Don’t Transmit.
Transmit
* Don’t Transmit
Codabar Check Character

Codabar check characters are created using different “modulos.” You can
program the scanner to read only Codabar bar codes with Modulo 16 check
characters. Default = No Check Character.
No Check Character indicates that the scanner reads and transmits bar
code data with or without a check character.
When Check Character is set to Validate and Transmit, the scanner will
only read Codabar bar codes printed with a check character, and will trans-
mit this character at the end of the scanned data.
6-3
When Check Character is set to Validate, but Don’t Transmit, the unit will
only read Codabar bar codes printed with a check character, but will not
transmit the check character with the scanned data.
* No Check Character
Validate Modulo 16, but

Don’t Transmit
Validate Modulo 16
and Transmit
Codabar Concatenation
Codabar supports symbol concatenation. When you enable concatena-
tion, the scanner looks for a Codabar symbol having a “D” start character,
adjacent to a symbol having a “D” stop character. In this case the two mes-
sages are concatenated into one with the “D” characters omitted.
A 1 2 3 4 D D 5 6 7 8 A
Select Require to prevent the scanner from decoding a single “D” Codabar
symbol without its companion. This selection has no effect on Codabar
symbols without Stop/Start D characters.
On
* Off
Require
6-4
Codabar Message Length
Scan the bar codes below to change the message length. Refer to
Message Length Description (page 6-2) for additional information. Mini-
mum and Maximum lengths = 2-60. Minimum Default = 4, Maximum
Default = 60.
Minimum Message Length
Maximum Message Length
6-5
Code 39
< Default All Code 39 Settings >
Code 39 On/Off
* On
Off
Code 39 Start/Stop Characters

Start/Stop characters identify the leading and trailing ends of the bar code.
You may either transmit, or not transmit Start/Stop characters. Default =
Don’t Transmit.
Transmit
* Don’t Transmit
Code 39 Check Character

No Check Character indicates that the scanner reads and transmits bar
code data with or without a check character.
When Check Character is set to Validate, but Don’t Transmit, the unit
only reads Code 39 bar codes printed with a check character, but will not
transmit the check character with the scanned data.
6-6
When Check Character is set to Validate and Transmit, the scanner only
reads Code 39 bar codes printed with a check character, and will transmit
this character at the end of the scanned data. Default = No Check Charac-
ter.
* No Check Character
Validate, but Don’t Transmit
Validate and Transmit
Code 39 Message Length

Default = 48.
Code 39 Append
This function allows the scanner to append the data from several Code 39
bar codes together before transmitting them to the host computer. When
the scanner encounters a Code 39 bar code with the append trigger char-
6-7
acter(s), it buffers Code 39 bar codes until it reads a Code 39 bar code that
does not have the append trigger. The data is then transmitted in the order
in which the bar codes were read (FIFO). Default = Off.
On
* Off
Full ASCII
If Full ASCII Code 39 decoding is enabled, certain character pairs within
the bar code symbol will be interpreted as a single character. For example:
$V will be decoded as the ASCII character SYN, and /C will be decoded as
the ASCII character #. Default = Off.
NUL %U DLE $P SP SPACE 0 0 @ %V P P ‘ %W p +P

SOH $A DC1 $Q ! /A 1 1 A A Q Q a +A q +Q
STX $B DC2 $R “ /B 2 2 B B R R b +B r +R
ETX $C DC3 $S # /C 3 3 C C S S c +C s +S
EOT $D DC4 $T $ /D 4 4 D D T T d +D t +T
ENQ $E NAK $U % /E 5 5 E E U U e +E u +U
ACK $F SYN $V & /F 6 6 F F V V f +F v +V
BEL $G ETB $W ‘ /G 7 7 G G W W g +G w +W
BS $H CAN $X ( /H 8 8 H H X X h +H x +X
HT $I EM $Y ) /I 9 9 I I Y Y i +I y +Y
LF $J SUB $Z * /J : /Z J J Z Z j +J z +Z
VT $K ESC %A + /K ; %F K K [ %K k +K { %P
FF $L FS %B , /L < %G L L \ %L l +L | %Q
CR $M GS %C - - = %H M M ] %M m +M } %R
SO $N RS %D . . > %I N N ^ %N n +N ~ %S
SI $O US %E / /O ? %J O O _ %O o +O DEL %T
6-8
Character pairs /M and /N decode as a minus sign and period respectively.
Character pairs /P through /Y decode as 0 through 9.
Full ASCII On
* Full ASCII Off
Code 39 Code Page

Code pages define the mapping of character codes to characters. If the
data received does not display with the proper characters, it may be
because the bar code being scanned was created using a code page that
is different from the one the host program is expecting. If this is the case,
scan the bar code below, select the code page with which the bar codes
were created (see Code Page Mapping of Printed Bar Codes on page A-6),
and scan the value and the Save bar code from the Programming Chart on
the inside the back cover of this manual. The data characters should then
appear properly.
Code 39 Code Page
6-9
Interleaved 2 of 5
< Default All Interleaved 2 of 5 Settings >
Interleaved 2 of 5 On/Off
* On
Off
Check Digit
No Check Digit indicates that the scanner reads and transmits bar code
data with or without a check digit.
When Check Digit is set to Validate, but Don’t Transmit, the unit only
reads Interleaved 2 of 5 bar codes printed with a check digit, but will not
transmit the check digit with the scanned data.
When Check Digit is set to Validate and Transmit, the scanner only reads
Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this
digit at the end of the scanned data. Default = No Check Digit.
* No Check Digit
6 - 10
Interleaved 2 of 5 Message Length
Default = 80.
NEC 2 of 5
< Default All NEC 2 of 5 Settings >
NEC 2 of 5 On/Off
* On
Off
Check Digit
No Check Digit indicates that the scanner reads and transmits bar code
data with or without a check digit.
When Check Digit is set to Validate, but Don’t Transmit, the unit only
reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit
the check digit with the scanned data.
6 - 11
When Check Digit is set to Validate and Transmit, the scanner only reads
NEC 2 of 5 bar codes printed with a check digit, and will transmit this digit
at the end of the scanned data. Default = No Check Digit.
* No Check Digit
NEC 2 of 5 Message Length

Default = 80.
6 - 12
Code 93
< Default All Code 93 Settings >
Code 93 On/Off
* On
Off

Default = 80.
Code 93 Append
this function is enabled, the scanner stores those Code 93 bar codes that
start with a space (excluding the start and stop symbols), and does not
immediately transmit the data. The scanner stores the data in the order in
6 - 13
which the bar codes are read, deleting the first space from each. The
scanner transmits the appended data when it reads a Code 93 bar code
that starts with a character other than a space. Default = Off.
On
* Off
Code 93 Code Page

appear properly.
Code 93 Code Page
6 - 14
Straight 2 of 5 Industrial (three-bar start/stop)
<Default All Straight 2 of 5 Industrial Settings>
Straight 2 of 5 Industrial On/Off
On
* Off
Straight 2 of 5 Industrial Message Length

Default = 48.
6 - 15
Straight 2 of 5 IATA (two-bar start/stop)
<Default All Straight 2 of 5 IATA Settings>
Straight 2 of 5 IATA On/Off
On
* Off
Straight 2 of 5 IATA Message Length

Default = 48.
6 - 16
Matrix 2 of 5
<Default All Matrix 2 of 5 Settings>
Matrix 2 of 5 On/Off
On
* Off
Matrix 2 of 5 Message Length

Default = 80.
6 - 17
Code 128
<Default All Code 128 Settings>
Code 128 On/Off
* On
Off
ISBT 128 Concatenation

In 1994 the International Society of Blood Transfusion (ISBT) ratified a
standard for communicating critical blood information in a uniform manner.
The use of ISBT formats requires a paid license. The ISBT 128 Application
Specification describes 1) the critical data elements for labeling blood prod-
ucts, 2) the current recommendation to use Code 128 due to its high
degree of security and its space-efficient design, 3) a variation of Code 128
that supports concatenation of neighboring symbols, and 4) the standard
layout for bar codes on a blood product label. Use the bar codes below to
turn concatenation on or off. Default =Off.
On
* Off
6 - 18
Default = 80.
Code 128 Append

the scanner encounters a Code 128 bar code with the append trigger char-
acter(s), it buffers Code 128 bar codes until it reads a Code 128 bar code
that does not have the append trigger. The data is then transmitted in the
order in which the bar codes were read (FIFO). Default = Off.
On
* Off
Code 128 Code Page

appear properly.
Code 128 Code Page
6 - 19
GS1-128
<Default All GS1-128 Settings>
GS1-128 On/Off
* On
Off
GS1-128 Message Length

Default = 80.
6 - 20
UPC-A
<Default All UPC-A Settings>
UPC-A On/Off
* On
Off
Note: When UPC-A Off is scanned, UPC-A bar codes are transmitted as EAN-
13.
UPC-A Check Digit

This selection allows you to specify whether the check digit should be
transmitted at the end of the scanned data or not. Default = On.
* On
Off
6 - 21
UPC-A Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the
beginning of the scanned data, but the unit can be programmed so it will
not transmit it. Default = On.
* On
Off
UPC-A Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC-A data.
Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
UPC-A Addenda Required

When Required is scanned, the scanner will only read UPC-A bar codes
that have addenda. You must then turn on a 2 or 5 digit addenda listed on
page 6-22. Default = Not Required.
Required
* Not Required
6 - 22
UPC-A Addenda Separator
When this feature is on, there is a space between the data from the bar
code and the data from the addenda. When turned off, there is no space.
Default = On.
* On
Off
UPC-A/EAN-13
with Extended Coupon Code
Use the following codes to enable or disable UPC-A and EAN-13 with Extended
Coupon Code. When left on the default setting (Off), the scanner treats Cou-
pon Codes and Extended Coupon Codes as single bar codes.
If you scan the Allow Concatenation code, when the scanner sees the coupon
code and the extended coupon code in a single scan, it transmits both as sepa-
rate symbologies. Otherwise, it transmits the first coupon code it reads.
If you scan the Require Concatenation code, the scanner must see and read
the coupon code and extended coupon code in a single read to transmit the
data. No data is output unless both codes are read.
Default = Off.
* Off
Allow Concatenation
Require Concatenation
6 - 23
Coupon GS1 DataBar Output
If you scan coupons that have both UPC and GS1 DataBar codes, you may
wish to scan and output only the data from the GS1 DataBar code. Scan the
GS1 Output On code below to scan and output only the GS1 DataBar code
data. Default = GS1 Output Off.
* GS1 Output Off
GS1 Output On
UPC-E0
<Default All UPC-E Settings>
UPC-E0 On/Off
Most U.P.C. bar codes lead with the 0 number system. To read these
codes, use the UPC-E0 On selection. If you need to read codes that lead
with the 1 number system, use UPC-E1 (page 6-27). Default = On.
* UPC-E0 On
UPC-E0 Off
6 - 24
UPC-E0 Expand
UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format.
Default = Off.
On
* Off
UPC-E0 Addenda Required

When Required is scanned, the scanner will only read UPC-E bar codes
that have addenda. Default = Not Required.
Required
* Not Required
UPC-E0 Addenda Separator

When this feature is On, there is a space between the data from the bar
code and the data from the addenda. When turned Off, there is no space.
Default = On.
* On
Off
6 - 25
UPC-E0 Check Digit
Check Digit specifies whether the check digit should be transmitted at the
end of the scanned data or not. Default = On.
* On
Off
UPC-E0 Number System

The numeric system digit of a U.P.C. symbol is normally transmitted at the
beginning of the scanned data, but the unit can be programmed so it will
not transmit it. To prevent transmission, scan Off. Default = On.
* On
Off
UPC-E0 Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC-E data.
2 Digit Addenda On
5 Digit Addenda On
6 - 26
UPC-E1
Most U.P.C. bar codes lead with the 0 number system. For these codes, use
UPC-E0 (page 6-24). If you need to read codes that lead with the 1 number
system, use the UPC-E1 On selection. Default = Off.
UPC-E1 On
* UPC-E1 Off
EAN/JAN-13
<Default All EAN/JAN Settings>
EAN/JAN-13 On/Off
* On
Off
Note: If you want to convert UPC-A bar codes to EAN-13 format, scan the UPC-
A Off bar code on page 6-21.
6 - 27
EAN/JAN-13 Check Digit
* On
Off
EAN/JAN-13 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13
data. Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
5 Digit Addenda On
EAN/JAN-13 Addenda Required

When Required is scanned, the scanner will only read EAN/JAN-13 bar
codes that have addenda. Default = Not Required.
Required
* Not Required
6 - 28
EAN/JAN-13 Addenda Separator
Default = On.
* On
Off
Note: If you want to enable or disable EAN13 with Extended Coupon Code,
refer to UPC-A/EAN-13 with Extended Coupon Code (page 6-23).
ISBN Translate
When On is scanned, EAN-13 Bookland symbols are translated into their
equivalent ISBN number format. Default = Off.
On
* Off
6 - 29
EAN/JAN-8
<Default All EAN/JAN-8 Settings>
EAN/JAN-8 On/Off
* On
Off
EAN/JAN-8 Check Digit

* On
Off
6 - 30
EAN/JAN-8 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data.
2 Digit Addenda On
5 Digit Addenda On
EAN/JAN-8 Addenda Required

When Required is scanned, the scanner will only read EAN/JAN-8 bar
codes that have addenda. Default = Not Required.
Required
* Not Required
EAN/JAN-8 Addenda Separator

Default = On.
* On
Off
6 - 31
MSI
<Default All MSI Settings>
MSI On/Off
On
* Off
MSI Check Character

Different types of check characters are used with MSI bar codes. You can
program the scanner to read MSI bar codes with Type 10 check charac-
ters. Default = Validate Type 10, but Don’t Transmit.
When Check Character is set to Validate Type 10/11 and Transmit, the
scanner will only read MSI bar codes printed with the specified type check
character(s), and will transmit the character(s) at the end of the scanned
data.
6 - 32
When Check Character is set to Validate Type 10/11, but Don’t Transmit,
the unit will only read MSI bar codes printed with the specified type check
character(s), but will not transmit the check character(s) with the scanned
data.
* Validate Type 10, but Don’t

Transmit
Validate Type 10 and Transmit
Validate 2 Type 10 Characters,

but Don’t Transmit
Validate 2 Type 10 Characters

and Transmit
Validate Type 10 then Type 11

Character, but Don’t Transmit
Validate Type 10 then

Type 11 Character and Transmit
Disable MSI Check Characters
MSI Message Length

Default = 48.
6 - 33
GS1 DataBar Omnidirectional
< Default All GS1 DataBar Omnidirectional Settings >
GS1 DataBar Omnidirectional On/Off
* On
Off
GS1 DataBar Limited

< Default All GS1 DataBar Limited Settings >
GS1 DataBar Limited On/Off
* On
Off
6 - 34
GS1 DataBar Expanded
< Default All GS1 DataBar Expanded Settings >
GS1 DataBar Expanded On/Off
* On
Off
GS1 DataBar Expanded Message Length

Default = 74.
6 - 35
Codablock A
<Default All Codablock A Settings>
Codablock A On/Off
On
* Off
Codablock A Message Length

Default = 600.
6 - 36
Codablock F
<Default All Codablock F Settings>
Codablock F On/Off
On
* Off
Codablock F Message Length

Default = 2048.
6 - 37
PDF417
< Default All PDF417 Settings >
PDF417 On/Off
* On
Off
PDF417 Message Length

Default = 2750.
6 - 38
MacroPDF417
MacroPDF417 is an implementation of PDF417 capable of encoding very large
amounts of data into multiple PDF417 bar codes. When this selection is
enabled, these multiple bar codes are assembled into a single data string.
Default = On.
* On
Off
MicroPDF417
< Default All MicroPDF417 Settings >
MicroPDF417 On/Off
On
* Off
6 - 39
MicroPDF417 Message Length
Default = 366.
GS1 Composite Codes

Linear codes are combined with a unique 2D composite component to form a
new class called GS1 Composite symbology. GS1 Composite symbologies
allow for the co-existence of symbologies already in use. Default = Off.
On
* Off
UPC/EAN Version
Scan the UPC/EAN Version On bar code to decode GS1 Composite sym-
bols that have a U.P.C. or an EAN linear component. (This does not affect
GS1 Composite symbols with a GS1-128 or GS1 linear component.)
Default = UPC/EAN Version Off.
UPC/EAN Version On
* UPC/EAN Version Off

Note: If you scan coupons that have both UPC and GS1 DataBar codes, you
may wish to scan and output only the data from the GS1 DataBar code.
See Coupon GS1 DataBar Output (page 6-24) for further information.
6 - 40
GS1 Composite Code Message Length
Default = 2435.
GS1 Emulation
The scanner can automatically format the output from any GS1 data carrier to
emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar
symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8,
ITF-14, GS1-128, and GS1-128 DataBar and GS1 Composites. (Any applica-
tion that accepts GS1 data can be simplified since it only needs to recognize
one data carrier type.)
If GS1-128 Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8,
EAN13) are expanded out to 16 digits. If the AIM ID is enabled, the value will be
the GS1-128 AIM ID, ]C1 (see Symbology Chart on page A-1).
If GS1 DataBar Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8,
EAN13) are expanded out to 16 digits. If the AIM ID is enabled, the value will be
the GS1-DataBar AIM ID, ]em (see Symbology Chart on page A-1).
If GS1 Code Expansion Off is scanned, retail code expansion is disabled, and
UPC-E expansion is controlled by the UPC-E0 Expand (page 6-25) setting. If
the AIM ID is enabled, the value will be the GS1-128 AIM ID, ]C1 (see
Symbology Chart on page A-1).
If EAN8 to EAN13 Conversion is scanned, all EAN8 bar codes are converted
to EAN13 format.
6 - 41
Default = GS1 Emulation Off.
GS1-128 Emulation
GS1 DataBar Emulation
GS1 Code Expansion Off
EAN8 to EAN13 Conversion
* GS1 Emulation Off
TCIF Linked Code 39 (TLC39)

This code is a composite code since it has a Code 39 linear component and a
MicroPDF417 stacked code component. All bar code readers are capable of
reading the Code 39 linear component. The MicroPDF417 component can only
be decoded if TLC39 On is selected. The linear component may be decoded
as Code 39 even if TLC39 is off. Default = Off.
On
* Off
6 - 42
QR Code
< Default All QR Code Settings >
QR Code On/Off
This selection applies to both QR Code and Micro QR Code.
* On
Off
QR Code Message Length

Default = 7089.
QR Code Append
This function allows the scanner to append the data from several QR Code
the scanner encounters an QR Code bar code with the append trigger
character(s), it buffers the number of QR Code bar codes determined by
6 - 43
information encoded in those bar codes. Once the proper number of codes
is reached, the data is output in the order specified in the bar codes.
Default = On.
* On
Off
QR Code Page
QR Code pages define the mapping of character codes to characters. If
the data received does not display with the proper characters, it may be
appear properly.
QR Code Page
6 - 44
Data Matrix
< Default All Data Matrix Settings >
Data Matrix On/Off
* On
Off
Data Matrix Message Length

Default = 3116.
Data Matrix Append

This function allows the scanner to append the data from several Data
Matrix bar codes together before transmitting them to the host computer.
When the scanner encounters an Data Matrix bar code with the append
trigger character(s), it buffers the number of Data Matrix bar codes deter-
6 - 45
mined by information encoded in those bar codes. Once the proper num-
ber of codes is reached, the data is output in the order specified in the bar
codes. Default = On.
* On
Off
Data Matrix Code Page

Data Matrix Code pages define the mapping of character codes to charac-
ters. If the data received does not display with the proper characters, it
may be because the bar code being scanned was created using a code
page that is different from the one the host program is expecting. If this is
the case, scan the bar code below, select the code page with which the bar
codes were created (see Code Page Mapping of Printed Bar Codes on
page A-6), and scan the value and the Save bar code from the
Programming Chart on the inside the back cover of this manual. The data
characters should then appear properly.
Data Matrix Code Page
6 - 46
Aztec Code
< Default All Aztec Code Settings >
Aztec Code On/Off
* On
Off
Aztec Code Message Length

Default = 3832.
Aztec Append
This function allows the scanner to append the data from several Aztec bar
codes together before transmitting them to the host computer. When the
scanner encounters an Aztec bar code with the append trigger charac-
6 - 47
ter(s), it buffers the number of Aztec bar codes determined by information
encoded in those bar codes. Once the proper number of codes is reached,
the data is output in the order specified in the bar codes. Default = Off.
On
* Off
Aztec Code Page

Aztec Code pages define the mapping of character codes to characters. If
the data received does not display with the proper characters, it may be
appear properly.
Aztec Code Page
6 - 48
Chinese Sensible (Han Xin) Code
< Default All Han Xin Settings >
Han Xin Code On/Off
On
* Off
Han Xin Code Message Length

Default = 7833.
Postal Codes - Linear

The following lists linear postal codes. Any combination of linear postal code
selections can be active at a time.
China Post (Hong Kong 2 of 5)

<Default All China Post (Hong Kong 2 of 5) Settings>
6 - 49
China Post (Hong Kong 2 of 5) On/Off
On
* Off
China Post (Hong Kong 2 of 5) Message Length

Message Length Description (page 6-2) for additional information.
Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maxi-
mum Default = 80.
6 - 50
Korea Post
<Default All Korea Post Settings>
Korea Post
On
* Off
Korea Post Message Length

Message Length Description (page 6-2) for additional information.
Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maxi-
mum Default = 48.
Korea Post Check Digit

transmitted at the end of the scanned data. Default = Don’t Transmit.
Transmit Check Digit
* Don’t Transmit Check Digit
6 - 51
6 - 52
7
Interface Keys
Keyboard Function Relationships

The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII
“CTRL”+ relationships apply to all terminals that can be used with the scanner.
Refer to page 2-13 enable Control + ASCII mode.
Function Code HEX/ASCII Value Full ASCII “CTRL” +

NUL 00 @
SOH 01 A
STX 02 B
ETX 03 C
EOT 04 D
ENQ 05 E
ACK 06 F
BEL 07 G
BS 08 H
HT 09 I
LF 0A J
VT 0B K
FF 0C L
CR 0D M
SO 0E N
SI 0F O
DLE 10 P
DC1 11 Q
DC2 12 R
DC3 13 S
DC4 14 T
NAK 15 U
SYN 16 V
ETB 17 W
CAN 18 X
EM 19 Y
SUB 1A Z
ESC 1B [
FS 1C \
GS 1D ]
RS 1E ^
US 1F _
7-1
The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to
US only. The following chart indicates the equivalents of these five characters
for different countries.
Country Codes
United States [ \ ] 6 -
Belgium [ < ] 6 -
Scandinavia 8 < 9 6 -
France ^ 8 $ 6 =
Germany Ã + 6 -
Italy \ + 6 -
Switzerland < .. 6 -
United Kingdom [ ¢ ] 6 -
Denmark 8 \ 9 6 -
Norway 8 \ 9 6 -
Spain [ \ ] 6 -
7-2
Supported Interface Keys
IBM PC/AT and
Compatibles, Apple Mac/iMac
ASCII HEX
USB PC Supported Keys
Keyboard
NUL 00 Reserved Reserved
SOH 01 Enter (KP) Enter/Numpad Enter
STX 02 Cap Lock CAPS
ETX 03 ALT make ALT make
EOT 04 ALT break ALT break
ENQ 05 CTRL make CNTRL make
ACK 06 CTRL break CNTRL break
BEL 07 CR/Enter RETURN
BS 08 Reserved APPLE make
HT 09 Tab TAB
LF 0A Reserved APPLE break
VT 0B Tab TAB
FF 0C Delete Del
CR 0D CR/Enter RETURN
SO 0E Insert Ins Help
SI 0F Escape ESC
DLE 10 F11 F11
DC1 11 Home Home
DC2 12 Print Prnt Scrn
DC3 13 Back Space BACKSPACE
DC4 14 Back Tab LSHIFT TAB
NAK 15 F12 F12
SYN 16 F1 F1
ETB 17 F2 F2
CAN 18 F3 F3
EM 19 F4 F4
SUB 1A F5 F5
ESC 1B F6 F6
FS 1C F7 F7
GS 1D F8 F8
RS 1E F9 F9
US 1F F10 F10
DEL 7F BACKSPACE
7-3
7-4
8
Utilities
To Add a Test Code I.D. Prefix to All Symbologies

This selection allows you to turn on transmission of a Code I.D. before the
decoded symbology. (See the Symbology Chart, beginning on page A-1) for
the single character code that identifies each symbology.) This action first
clears all current prefixes, then programs a Code I.D. prefix for all symbologies.
This is a temporary setting that will be removed when the unit is power cycled.
Add Code I.D. Prefix to

All Symbologies (Temporary)
Show Decoder Revision

Scan the bar code below to output the decoder revision.
Show Decoder Revision
Show Scan Driver Revision

Scan the bar code below to output the scan driver revision. The scan driver
controls image capture.
Show Scan Driver Revision
Show Software Revision

Scan the bar code below to output the current software revision, unit serial num-
ber, and other product information.
Show Revision
8-1
Show Data Format
Scan the bar code below to show current data format settings.
DFMBK3?.
Data Format Settings
Test Menu
When you scan the Test Menu On code, then scan a programming code in this
manual, the scanner displays the content of a programming code. The pro-
gramming function will still occur, but in addition, the content of that program-
ming code is output to the terminal.
Note: This feature should not be used during normal scanner operation.
On
* Off
8-2
9
Product Specifications
Youjie 4600 Scanner Product Specifications

Parameter Specification
Mechanical
Height 2.9 inches (75mm)
Length 6.7 inches (170mm)
Width 2.6 inches (66mm)
Weight 4.2 ounces (119g)
Electrical
Input Voltage 4 to 5.5VDC
Operating Power 2W; 400 mA (typical) @ 5V
Standby Power .45W; 90 mA (typical) @ 5V
Environmental
Operating Temperature 32°F to 104°F (0°C to 40°C)
Storage Temperature -40°F to 140°F (-40°C to 60°C)
Humidity 0 to 95% non-condensing
Drop Operational after 12 drops to concrete from 2 ft. (1m)
Environmental Sealing IP40
Light Levels 0 - 100,000 lux (direct sunlight)
Up to 10kv direct air
ESD
Up to 4kv indirect coupling plane
Motion Tolerance 100mm per second for 13 mil UPC
Scan Performance
Pitch, Skew 60°, 70°
Symbol Contrast 35%
DOF with 5 mil, 1D bar code
Typical Performance
5 mil Code 39 33 - 95mm (1.3 - 3.7 in.)
13 mil UPC-A 32 - 255mm (1.3 - 10 in.)
20 mil Code 39 35 - 355mm (1.4 - 14 in.)
6.7 mil PDF417 30 - 95mm (1.2 - 3.7 in.)
10mil Data Matrix 30 - 100mm (1.2 - 3.9 in.)
15mil Data Matrix 21 - 162mm (0.8 - 6.4 in.)
20mil QR Code 23 - 200mm (0.9 - 7.9 in.)
9-1
9-2
10 Pin RJ45 Modular Plug
1 Cable shield
2 Cable select
Keyboard Wedge
3 Supply ground
4 Terminal data
5 Terminal clock
Standard Cable Pinouts
6 Keyboard clock
7 Supply power input +5V power
8 Keyboard data
9
10
Note: Pin assignments are not compatible withlegacy products.

Use of a cable with improper pin assignments may lead to damage to the unit.
Use of any cables not provided by the manufacturer may result in damage not
covered by your warranty.
USB
1 Cable shield
10 Pin Modular Plug
2 Cable select
3 Supply ground
4
5
6
7 +5V power
8
Standard Cable Pinouts
9 Data +
10 Data -
Note: Pin assignments are not compatible with legacy products.

Use of a cable with improper pin assignments may lead to damage to the unit.
Use of any cables not provided by the manufacturer may result in damage not
covered by your warranty.
9-3
9-4
10
Maintenance
Repairs
Repairs and/or upgrades are not to be performed on this product. These ser-
vices are to be performed only by an authorized service center (see Customer
Support on page 11-1).
Maintenance
Your device provides reliable and efficient operation with a minimum of care.
Although specific maintenance is not required, the following periodic checks
ensure dependable operation:
Cleaning the Device

Reading performance may degrade if the scanner’s window is not clean. If
the window is visibly dirty, or if the scanner isn’t operating well, clean the
window with a soft cloth or lens tissue dampened with water (or a mild
detergent- water solution). If a detergent solution is used, rinse with a
clean lens tissue dampened with water only.
The scanner and base’s housing may also be cleaned the same way.
! Caution:
Do not submerge the scanner in water. The scanner’s
housing is not watertight.
Do not use abrasive wipes or tissues on the scanner’s

window – abrasive wipes may scratch the window. Never
use solvents (e.g., alcohol or acetone) on the housing or
window – solvents may damage the finish or the window.
Inspecting Cords and Connectors

Inspect the interface cable and connector for wear or other signs of dam-
age. A badly worn cable or damaged connector may interfere with scanner
operation. Contact your distributor for information about cable replace-
ment. Cable replacement instructions are on page 10-1.
Replacing Cables
The standard interface cable is attached to the scanner with an 10-pin modular
connector. When properly seated, the connector is held in the scanner’s handle
by a flexible retention tab. The interface cable is designed to be field replace-
able.
10 - 1
• Order replacement cables from Youjie or from an authorized distributor.
• When ordering a replacement cable, specify the cable part number of the
original interface cable.
Replacing an Interface Cable

1. Turn the power to the host system OFF.
2. Disconnect the scanner’s cable from the

terminal or computer.
3. Locate the small hole on the back of the
scanner’s handle. This is the cable release.
4. Straighten one end of a paper clip.
5. Insert the end of the paper clip into the small
hole and press in. This depresses the
retention tab, releasing the connector. Pull
the connector out while maintaining
pressure on the paper clip, then remove the Cable
paper clip. Release
6. Replace with the new cable.
Insert the connector into the opening and
press firmly. The connector is keyed to go in only one way, and will
click into place.
Troubleshooting a Youjie 4600 Scanner

The scanner automatically performs self-tests whenever you turn it on. If
your scanner is not functioning properly, review the following Troubleshoot-
ing Guide to try to isolate the problem.
Is the power on? Is the aimer on?
If the aimer isn’t illuminated, check that:
• The cable is connected properly.
• The host system power is on (if external power isn’t used).
• The button works.
Is the scanner having trouble reading your symbols?
If the scanner isn’t reading symbols well, check that the scanner window is
clean and that the symbols:
• Aren’t smeared, rough, scratched, or exhibiting voids.
• Aren’t coated with frost or water droplets on the surface.
• Are enabled in the scanner or in the decoder to which the scanner
connects.
Is the bar code displayed but not entered?
The bar code is displayed on the host device correctly, but you still have to
press a key to enter it (the Enter/Return key or the Tab key, for example).
10 - 2
• You need to program a suffix. Programming a suffix enables the scanner
to output the bar code data plus the key you need (such as “CR”) to enter
the data into your application. Refer to Prefix/Suffix Overview beginning
on page 4-1 for further information.
Does the scanner read the bar code incorrectly?
If the scanner reads a bar code, but the data is not displayed correctly on
the host screen:
• The scanner may not be programmed for the appropriate terminal
interface.
For example, you scan “12345” and the host displays “@es%.”
Reprogram the scanner with the correct Plug and Play bar code. See
Programming the Interface beginning on page 2-1.
• The scanner may not be programmed to output your bar code data
properly.
For example, you scan “12345” and the host displays “A12345B.”
Reprogram the scanner with the proper symbology selections. See
Chapter 6.
The scanner won’t read your bar code at all.
1. Scan the sample bar codes in the back of this manual. If the scanner
reads the sample bar codes, check that your bar code is readable.
Verify that your bar code symbology is enabled (see Chapter 6).
If the scanner still can’t read the sample bar codes, scan All Symbologies
(page 6-2).
If you aren’t sure what programming options have been set in the scanner,
or if you want the factory default settings restored, refer to Resetting the
Factory Defaults on page 1-5.
10 - 3
10 - 4
11
Customer Support
Technical Assistance
Contact information for technical support, product service, and repair can be
found at www.youjieaidc.com.
Limited Warranty
Youjie warrants its products to be free from defects in materials and workman-
ship and to conform to Youjie’s published specifications applicable to the prod-
ucts purchased at the time of shipment. This warranty does not cover any
Youjie product which is (i) improperly installed or used; (ii) damaged by accident
or negligence, including failure to follow the proper maintenance, service, and
cleaning schedule; or (iii) damaged as a result of (A) modification or alteration
by the purchaser or other party, (B) excessive voltage or current supplied to or
drawn from the interface connections, (C) static electricity or electro-static dis-
charge, (D) operation under conditions beyond the specified operating parame-
ters, or (E) repair or service of the product by anyone other than Youjie or its
authorized representatives.
This warranty shall extend from the time of shipment for the duration published
by Youjie for the product at the time of purchase ("Warranty Period"). Any
defective product must be returned (at purchaser’s expense) during the War-
ranty Period to Youjie factory or authorized service center for inspection. No
product will be accepted by Youjie without a Return Materials Authorization,
which may be obtained by contacting Youjie. In the event that the product is
returned to Youjie or its authorized service center within the Warranty Period
and Youjie determines to its satisfaction that the product is defective due to
defects in materials or workmanship,Youjie, at its sole option, will either repair or
replace the product without charge, except for return shipping to Youjie.
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE
FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR
WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR NON-
INFRINGEMENT.
YOUJIE’S RESPONSIBILITY AND PURCHASER’S EXCLUSIVE REMEDY
UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
OF THE DEFECTIVE PRODUCT WITH NEW OR REFURBISHED PARTS. IN
NO EVENT SHALL Youjie BE LIABLE FOR INDIRECT, INCIDENTAL, OR CON-
SEQUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY LIABILITY OF
Youjie ARISING IN CONNECTION WITH ANY PRODUCT SOLD HEREUN-
DER (WHETHER SUCH LIABILITY ARISES FROM A CLAIM BASED ON
CONTRACT, WARRANTY, TORT, OR OTHERWISE) EXCEED THE ACTUAL
AMOUNT PAID TO Youjie FOR THE PRODUCT. THESE LIMITATIONS ON
LIABILITY SHALL REMAIN IN FULL FORCE AND EFFECT EVEN WHEN You-
jie MAY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES,
LOSSES, OR DAMAGES. SOME STATES, PROVINCES, OR COUNTRIES DO
11 - 1
NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CON-
SEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU.
All provisions of this Limited Warranty are separate and severable, which
means that if any provision is held invalid and unenforceable, such determina-
tion shall not affect the validity of enforceability of the other provisions hereof.
Use of any peripherals not provided by the manufacturer may result in damage
not covered by this warranty. This includes but is not limited to: cables, power
supplies, cradles, and docking stations. Youjie extends these warranties only to
the first end-users of the products. These warranties are non-transferable.
The duration of the limited warranty for the Youjie 4600 scanner is ninety
(90)days.
11 - 2
A
Reference Charts
Symbology Chart
Possible
AIM ID Code ID
Symbology AIM ID
Modifiers (hex)
( m)
All Symbologies (0x99)
Australian Post ]X0 A (0x41)
Aztec Code ]zm 0-9, A-C z (0x7A)
Batch Mode Quantity 5 (0x35)
British Post ]X0 B (0x42)
Canadian Post ]X0 C (0x43)
China Post ]X0 Q (0x51)
Chinese Sensible Code (Han Xin ]X0 H (0x48)
Code)
Codabar ]Fm 0-1 a (0x61)
Codablock A ]O6 0, 1, 4, 5, 6 V (0x56)
Codablock F ]Om 0, 1, 4, 5, 6 q (0x71)
Code 11 ]H3 h (0x68)
Code 128 ]Cm 0, 1, 2, 4 j (0x6A)
GS1-128 ]C1 I (0x49)
Code 32 Pharmaceutical (PARAF) ]X0 < (0x3C)
Code 39 (supports Full ASCII ]Am 0, 1, 3, 4, 5, 7 b (0x62)
mode)
Code 49 ]Tm 0, 1, 2, 4 l (0x6C)
Code 93 and 93i ]Gm 0-9, A-Z, i (0x69)
a-m
Data Matrix ]dm 0-6 w (0x77)
EAN-13 (including Bookland EAN) ]E0 d (0x64)
EAN-13 with Add-On ]E3 d (0x64)
EAN-13 with Extended ]E3 d (0x64)
Coupon Code
EAN-8 ]E4 D (0x44)
A-1
Possible
AIM ID Code ID
Symbology AIM ID
Modifiers (hex)
( m)
EAN-8 with Add-On ]E3 D (0x44)
GS1 Composite ]em 0-3 y (0x79)
GS1 DataBar ]em 0 y (0x79)
GS1 DataBar Limited ]em { (0x7B)
GS1 DataBar Omnidirectional ]em y (0x79)
GS1 DataBar Expanded ]em } (0x7D)
InfoMail ]X0 , (0x2c)
Intelligent Mail Bar Code ]X0 M (0x4D)
Interleaved 2 of 5 ]Im 0, 1, 3 e (0x65)
Japanese Post ]X0 J (0x4A)
KIX (Netherlands) Post ]X0 K (0x4B)
Korea Post ]X0 ? (0x3F)
Matrix 2 of 5 ]X0 m (0x6D)
MaxiCode ]Um 0-3 x (0x7 8)
MicroPDF417 ]Lm 3-5 R (0x52)
MSI ]Mm 0 g (0x67)
NEC 2 of 5 ]X0 Y (0x59)
OCR MICR (E 13 B) ]o3 O (0x4F)
OCR SEMI Font ]o3 O (0x4F)
OCR-A ]o1 O (0x4F)
OCR-B ]o2 O (0x4F)
PDF417 ]Lm 0-2 r (0x72)
Planet Code ]X0 L (0x4C)
Postal-4i ]X0 N (0x4E)
Postnet ]X0 P (0x50)
QR Code and Micro QR Code ]Qm 0-6 s (0x73)
Straight 2 of 5 IATA ]Rm 0, 1, 3 f (0x66)
Straight 2 of 5 Industrial ]S0 f (0x66)
A-2
Possible
AIM ID Code ID
Symbology AIM ID
Modifiers (hex)
(m)
TCIF Linked Code 39 (TLC39) ]L2 T (0x54)
Telepen ]Bm t (0x54)
UPC-A ]E0 c (0x63)
UPC-A with Add-On ]E3 c (0x63)
UPC-A with Extended ]E3 c (0x63)
Coupon Code
UPC-E ]E0 E (0x45)
UPC-E with Add-On ]E3 E (0x45)
UPC-E1 ]X0 E (0x45)
Note: “m” represents the AIM modifier character. Refer to International

Technical Specification, Symbology Identifiers, for AIM modifier character
details.
Prefix/Suffix entries for specific symbologies override the universal (All
Symbologies, 99) entry.
Refer to Data Editing beginning on page 4-1 and Data Formatting beginning on
page 5-1 for information about using Code ID and AIM ID.
A-3
ASCII Conversion Chart (Code Page 1252)
Note: This table applies to U.S. style keyboards. Certain characters may differ
depending on your Country Code/PC regional settings.
Non-Printable Characters
DEC HEX Character (Code) DEC HEX Character (Code)
0 0 NULL 16 10 DATA LINK ESCAPE (DLE)
1 1 START OF HEADING 17 11 DEVICE CONTROL 1 (DC1)
(SOH)
2 2 START OF TEXT (STX) 18 12 DEVICE CONTROL 2 (DC2)
3 3 END OF TEXT (ETX) 19 13 DEVICE CONTROL 3 (DC3)
4 4 END OF TRANSMISSION 20 14 DEVICE CONTROL 4 (DC4)
(EOT)
5 5 END OF QUERY (ENQ) 21 15 NEGATIVE ACKNOWLEDGE-
MENT (NAK)
6 6 ACKNOWLEDGE (ACK) 22 16 SYNCHRONIZE (SYN)
7 7 BEEP (BEL) 23 17 END OF TRANSMISSION
BLOCK (ETB)
8 8 BACKSPACE (BS) 24 18 CANCEL (CAN)
9 9 HORIZONTAL TAB (HT) 25 19 END OF MEDIUM (EM)
10 A LINE FEED (LF) 26 1A SUBSTITUTE (SUB)
11 B VERTICAL TAB (VT) 27 1B ESCAPE (ESC)
12 C FF (FORM FEED) 28 1C FILE SEPARATOR (FS)
RIGHT ARROW
13 D CR (CARRIAGE RETURN) 29 1D GROUP SEPARATOR (GS)
LEFT ARROW
14 E SO (SHIFT OUT) 30 1E RECORD SEPARATOR (RS)
UP ARROW
15 F SI (SHIFT IN) 31 1F UNIT SEPARATOR (US)
DOWN ARROW
Printable Characters
DEC HEX Character DEC HEX Character DEC HEX Character
32 20 <SPACE> 64 40 @ 96 60 `
33 21 ! 65 41 A 97 61 a
34 22 " 66 42 B 98 62 b
35 23 # 67 43 C 99 63 c
36 24 $ 68 44 D 100 64 d
37 25 % 69 45 E 101 65 e
38 26 & 70 46 F 102 66 f
39 27 ' 71 47 G 103 67 g
A-4
Printable Characters (Continued)
40 28 ( 72 48 H 104 68 h
41 29 ) 73 49 I 105 69 i
42 2A * 74 4A J 106 6A j
43 2B + 75 4B K 107 6B k
44 2C , 76 4C L 108 6C l
45 2D - 77 4D M 109 6D m
46 2E . 78 4E N 110 6E n
47 2F / 79 4F O 111 6F o
48 30 0 80 50 P 112 70 p
49 31 1 81 51 Q 113 71 q
50 32 2 82 52 R 114 72 r
51 33 3 83 53 S 115 73 s
52 34 4 84 54 T 116 74 t
53 35 5 85 55 U 117 75 u
54 36 6 86 56 V 118 76 v
55 37 7 87 57 W 119 77 w
56 38 8 88 58 X 120 78 x
57 39 9 89 59 Y 121 79 y
58 3A : 90 5A Z 122 7A z
59 3B ; 91 5B [ 123 7B {
60 3C < 92 5C \ 124 7C |
61 3D = 93 5D ] 125 7D }
62 3E > 94 5E ^ 126 7E ~
63 3F ? 95 5F _ 127 7F <DEL>
Extended ASCII Characters

128 80 €€ 171 AB « 214 D6 Ö
129 81 172 AC ¬ 215 D7 ×
130 82 ‚ 173 AD 216 D8 Ø
131 83 ƒ 174 AE ® 217 D9 Ù
132 84 „ 175 AF ¯ 218 DA Ú
133 85 … 176 B0 ° 219 DB Û
134 86 † 177 B1 ± 220 DC Ü
135 87 ‡ 178 B2 ² 221 DD Ý
136 88 ˆ 179 B3 ³ 222 DE Þ
137 89 ‰ 180 B4 ´ 223 DF ß
138 8A Š 181 B5 µ 224 E0 à
139 8B ‹ 182 B6 ¶ 225 E1 á
A-5
Extended ASCII Characters (Continued)
140 8C Œ 183 B7 · 226 E2 â
141 8D 184 B8 ¸ 227 E3 ã
142 8E Ž 185 B9 ¹ 228 E4 ä
143 8F 186 BA º 229 E5 å
144 90 187 BB » 230 E6 æ
145 91 ‘ 188 BC ¼ 231 E7 ç
146 92 ’ 189 BD ½ 232 E8 è
147 93 “ 190 BE ¾ 233 E9 é
148 94 ” 191 BF ¿ 234 EA ê
149 95 • 192 C0 À 235 EB ë
150 96 – 193 C1 Á 236 EC ì
151 97 — 194 C2 Â 237 ED í
152 98 ˜ 195 C3 Ã 238 EE î
153 99 ™ 196 C4 Ä 239 EF ï
154 9A š 197 C5 Å 240 F0 ð
155 9B › 198 C6 Æ 241 F1 ñ
156 9C œ 199 C7 Ç 242 F2 ò
157 9D 200 C8 È 243 F3 ó
158 9E ž 201 C9 É 244 F4 ô
159 9F Ÿ 202 CA Ê 245 F5 õ
160 A0 203 CB Ë 246 F6 ö
161 A1 ¡ 204 CC Ì 247 F7 ÷
162 A2 ¢ 205 CD Í 248 F8 ø
163 A3 £ 206 CE Î 249 F9 ù
164 A4 ¤ 207 CF Ï 250 FA ú
165 A5 ¥ 208 D0 Ð 251 FB û
166 A6 ¦ 209 D1 Ñ 252 FC ü
167 A7 § 210 D2 Ò 253 FD ý
168 A8 ¨ 211 D3 Ó 254 FE þ
169 A9 © 212 D4 Ô 255 FF ÿ
170 AA ª 213 D5 Õ
Code Page Mapping of Printed Bar Codes

Code pages define the mapping of character codes to characters. If the data
received does not display with the proper characters, it may be because the bar
code being scanned was created using a code page that is different from the
A-6
one the host program is expecting. If this is the case, select the code page with
which the bar codes were created. The data characters should then appear
properly.
Code Page Standard Description

1 CP ISO646
2 (Default) ISO 2022 Automatic National Replacement
Characters
3 CP Binary
51 ISO 8859 1 51 Western European Replacement
Characters
82 ISO 2022 11 Swe Swedish Replacement Characters
83 ISO 2022 69 Fra French/Belgium Replacement
Characters
81 ISO 2022 25 Fra French/Belgium Replacement
Characters
84 ISO 2022 11 Ger German Replacement Characters
85 ISO 2022 11 Ita Italian Replacement Characters
86 ISO 2022 11 Swi Swiss Replacement Characters
87 ISO 2022 11 UK British Replacement Characters
88 ISO 2022 11 Dan Danish Replacement Characters
89 ISO 2022 11 Nor Norwegian Replacement Characters
90 ISO 2022 11 Spa Spanish Replacement Characters
91 ISO 2022 85 Spanish Replacement Characters
92 ISO 2022 16 Portuguese Replacement Characters
93 ISO 2022 84 Portuguese Replacement Characters
94 ISO 2022 60 Norwegian Replacement Characters
A-7
Unicode Key Maps
6E 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F 4B 50 55 5A 5F 64 69
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 5B 60 65
6A
1E 1F 20 21 22 23 24 25 26 27 28 29 2B 5C 61 66
2C 2E 2F 30 31 32 33 34 35 36 37 39 53 5D 62 67
4F 54 59 6C
3A 3B 3C 3D 3E 3F 38 40 63 68
104 Key U.S. Style Keyboard
6E 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F 4B 50 55 5A 5F 64 69
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 2B 4C 51 56 5B 60 65
6A
1E 1F 20 21 22 23 24 25 26 27 28 29 2A 5C 61 66
2C 2D 2E 2F 30 31 32 33 34 35 36 37 39 53 5D 62 67
4F 54 59 6C
3A 3B 3C 3D 3E 3F 38 40 63 68
105 Key European Style Keyboard
A-8
Sample Symbols
UPC-A
0 123456 7890 Interleaved 2 of 5
Code 128 1234567890
Code 128 EAN-13
Code 39 9 780330 290951
Codabar
BC321
Code 93
A13579B
123456-9$
Straight 2 of 5 Industrial
123456
Sample Symbols
Matrix 2 of 5
6543210 GS1 DataBar
PDF417
(01)00123456789012
Car Registration
Data Matrix
QR Code Test Symbol
Numbers
4-CB (4-State Customer Bar Code)
01,234,567094,987654321,01234567891
ID-tag (UPU 4-State)
J18CUSA8E6N062315014880T
Sample Symbols
Aztec
Micro PDF417
Package Label
MaxiCode
Test Message
Test Message
Programming Chart
9
Programming Chart
Save
Discard
Reset
Note: If you make an error while scanning the letters or digits (before scanning
Save), scan Discard, scan the correct letters or digits, and Save again.
YG4600-UG Rev A
6/12

Yj4600 PDF

Uploaded by

Copyright:

Available Formats

Yj4600 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Yj4600 PDF

Uploaded by

Copyright:

Available Formats

YJ4600

Waste Electrical and Electronic Equipment

Solids and Water Protection

Chapter 1 - Getting Started

Chapter 2 - Programming the Interface

Chapter 3 - Input/Output Settings

Chapter 4 - Data Editing

Chapter 7 - Interface Keys

Chapter 9 - Product Specifications

Chapter 11 - Customer Support

Appendix A - Reference Charts

About This Manual

Unpacking Your Device

Connecting the Device

2. The scanner beeps.

Connecting with Keyboard Wedge

3. Turn the terminal/computer power back on. The scanner beeps.

Linear bar code 2D Matrix symbol

Menu Bar Code Security Settings

Set Custom Defaults

Save Custom Defaults

Resetting the Custom Defaults

Activate Custom Defaults

Remove Custom Defaults

Programming the Interface - Plug and Play

IBM PC AT and Compatibles with

Laptop Direct Connect

Laptop Direct Connect

USB IBM SurePos

USB IBM SurePos

Symbology Suffix Symbology Suffix

USB PC or Macintosh Keyboard

USB Keyboard (PC)

USB Keyboard (Mac)

USB Japanese Keyboard (PC)

USB HID Bar Code Scanner

United States (Dvorak)

United States (Dvorak left)

United States (Dvorak right)

United States (International)

Canada (French legacy)

Greek (220 Latin)

Greek (319 Latin)

Hungarian (101 key)

United Stated (Dvorak right)

United States (Dvorak left)

United States (Dvorak)

United States (International)

Automatic Caps Lock

Autocaps via NumLock

Emulate External Keyboard

* Keyboard Conversion Off

Convert All Characters

Convert All Characters

Control Character Output

Control Character Output On

* Control Character Output Off

Windows Mode Control + ASCII

* Control + ASCII Mode Off