CV-5000S installation manual

(Ver.4)

TOPCON CORPORATION
July 2011
 Index

1. Basic configuration................................................................................................................................................2
2. Mounting the CV-5000S Phoropter head...........................................................................................................4
3. Connection of head/power supply and controller .............................................................................................5
4. Installation of PC software (setup 3)...................................................................................................................7
5. Connection with chart .........................................................................................................................................14
6. Connection with refraction instruments............................................................................................................28
7. Output subjective data to PC.............................................................................................................................44
8. Network system 1................................................................................................................................................52
9. Network system 2................................................................................................................................................55
10. Network system 3..............................................................................................................................................59
11. Network system 4..............................................................................................................................................64
12. Network system 5..............................................................................................................................................69
13. Network system 6..............................................................................................................................................72
14. Details of setting menu.....................................................................................................................................77
15. Customizing pictures and movies (PC-50S only).........................................................................................78
16. Export and import settings with USB memory ..............................................................................................80
17. Update KB-50S..................................................................................................................................................81

1
1. Basic configuration

SETUP 1
(KB-50S)

SETUP 2
(MONITOR & MOUSE)

SETUP 3
(PC)

SETUP 1 Basic components

2. 3.
1.

1. 432239501 Phoropter head with arm

2. 432249700 Power supply with built-in PC

with built-in printer,
with measuring head connection cable and power cord.

3. 432259500 KB-50S (one dial controller)

with USB/DC interface cable.

2
 SETUP 2 Basic components

1. 3.
2.

5.
4.

1.432239501 Phoropter head with arm.

2.432249700 Power supply with built-in PC Monitor

with built-in printer, z analogue
with measuring head connection cable and power cord. z VGA interface
z 1024x768 resolution or more
3. Monitor (locally arrange)
4. USB mouse (locally arrange)

5.VGA cable (locally arrange)

SETUP3 3 Basic component

1.

2. 3. 4.

1.432239501 Phoropter head with arm.

2. 432249702 Power supply

with measuring head connection cable and power cord.
PC requirements
(without printer)
Windows XP Professional SP3
with CV-5000PC software.
Windows 7 Professional 32bit
Windows 7 Professional 64bit
3. 418120002 RS-232C serial cable (Din8 – Dsub9) (5m)
or 424290061 RS-232C serial cable (Din8 – Dsub9) (10m)
In case of Internet Explorer Ver.8, a
or RS-232C-USB conversion cable (locally arranged)
security patch file “KB2482017” should be
installed.
4. PC (locally arrange)
Monitor (DVI or VGA), USB mouse / Keyboard, Printer
9 1280x1024 resolution monitor
9 At least one serial port.
3
2. Mounting the CV-5000S Phoropter head
See the instruction manual CV-5000S as well.
2-1. Level adjustment

2-2. Check the face shield and forehead rest.

2-3. Near point head and rod installation.

4
3. Connection of head/power supply and controller
3-1. SETUP 1
Connect power supply box, measuring head, KB-50S and power cord.

Measuring head connection cable

Power cord

KB-50S USB/DC
interface cable.

5
3-2. SETUP 2
Connect power supply box, measuring head, analogue monitor, mouse, and power cord.

VGA cable

Power cord Measuring head connection cable

3-3. SETUP 3
Connect power supply box, measuring head, PC and power cord.

RS-232C cable

Measuring head connection cable

Power cord

6
4. Installation of PC software (setup 3)

4-1. PC requirements
Windows XP Professional SP3
Windows 7 Professional 32bit
Windows 7 Professional 64bit
* In case of Internet Explorer Ver.8, install Microsoft security update program “KB2482017”.

At least one serial port is necessary (to connect power supply box and PC), and make sure that COM port is
recognized.

*Monitor resolution must be 1280 x 1024 or more.

4-2. Install the software.

4-2.1. Turn on the PC
4-2.2. Insert the CV-5000 CD into CD/DVD drive of the PC.
4-2.3. Select [Main Installer_E] _ [CV5000_Updater]

4-2.4. Click [CV5000_Updater.exe].

7
4-2.5. Click [Start Setup]

4-2.6. Check the installation destination folder.

(Default is C:¥ProgramFiles¥TOPCON¥CV-5000S)

Tick in [Create shortcut icon on the Desktop]

Tick in [Create shortcut icon on the Startup]

Click [Start Setup].

8
4-2.7. Click [Start Setup]

4-2.8. Click [Start Setup]

9
4-2.9. Click [Start Setup]

z Please wait if you find the “not responding”.

4-2.10. Click [OK] to finish installation.

10
4-3. Initial settings

4-3.1. Power up the power supply box and start [CV-5000PC] software.

4-3.2. The following dialogue appears to check COM port. Click OK

4-3.3. In [Initial Settings], select followings.

[For Far Vision]

Device: the chart device to use.
ACP8, MC-3, PC-50, PC-50S or CC-100

Type: the chart type to use.

Chart type (A, B(M/F), C, D, F, H, IS)

Chart monitor selection: (in case of PC-50S)

Please select #: Plug and play monitor (=PC-50S)

Interface: (in case of ACP/MC/PC-50)

2 options of signal communication.
-IR emitter
-RS232C

[For Near Vision]

Device: the chart device to use
NC-3, NV20
Type: E/J

* Settings can be changed later, this process is necessary for start the software first time.

11
4-3.4. Select [serial port for CV power supply unit].
Select in the pull down menu, as there are COM numbers which are recognized are listed.

4-4. PC-50S setting.

In case of using PC-50S, adjust the display setting.
(1) Right click on the desktop, and select [Display Properties]
(2) Select [Settings]
(3) Select [Display]_[#:Plug and play monitor].
(4) Click [Identify] and make sure the selected number is displayed on PC-50S.
(5) Make sure the resolution is “1280x 1024” and 32 bit color.
(6) Tick in [Extend my Windows desktop onto this monitor].
(7) Click [OK]

12
4-5. Printer setting

SETUP 3 does not have the built-in printer, thus please arrange a printer for PC if required.
The following is recommended to print setting to have report much clearer to see with highlights on title.

In case of Internet Explorer 6 / Internet Explorer 7.

select [Internet Explorer]_[Tools]_[Internet Options]_[Advanced]
Tick in “Print background colors and images”.

In case of Internet Explorer 8,

select [Internet Explorer]_[Files]_[Page setup] *If the menu bar is hidden, press [Alt] key.

Tick in “ Print Background Colors and Images “.

13
5. Connection with chart
General information about cables

‹ Wireless DVI
EZ AIR USB/DVI wireless doc
http://www.ezairwireless.com/

‹ 424280001 DVI (10m)

‹ 432140006 (RS232C Din8-Din8) 5m

‹ 432140010 (RS232C Din8-Din8) 10m

‹ 418120002 (RS232C Din8 Dsub9) 5m

‹ 424290061 (RS232C Din8 Dsub9) 10m

‹ 424120005 IR emittor

Chart lineups

PC-50S : 424289700 ACP-8 series MC-3 PC-50

CC-100 series

14
General layout of CV-5000S system and chart device

SETUP 1 or 2

(1)
SETUP 3

(2)
PC-50S
Exclusively in use with CV-5000S
(1) EZAir wireless DVI No remote controller is available
(2) 424280001 DVI (10m)

SETUP 1, 2, or 3

ACP-8 series

(1)

PC-50
(2)
CC-100 series

(1) ACP/MC-3 : 432140006 (RS232C Din8-Din8)

PC-50 : 424290061 (RS232C Din8 Dsub9)
MC-3
(2) IR emittor 424120005

Remote controller is available

(optional accessory)
Stand alone use is available

15
5-1. PC-50S for SETUP 1 and 2.
Please see Instruction Manual PC-50S for how to install PC-50S.

5-1.1. Cabling
Connect DVI cable to DVI socket of power supply.

DVI cable

5-1.2. Settings in CV-5000S

(1)When CV-5000S and PC-50S first time, the initial settings screen comes up.

For other cases,

(SETUP1) Press [Shift]&[Menu] button, and select [Settings]_[Chart Settings]

(SETUP2) Click [Settings] icon and

click [Chart Settings].

16
(2) Select “For far vision”,
Device = PC-50S
Type = Chart A, B, E, F,H
(at your convenience)

Chart Monitor Selection

= #:PC-50S
(#: is automatically assigned)

z #:Plug and play monitor

stands for the monitor for control in Setup2.

(2)’ (Especially in SETUP2) Touch the mark, so that you can see the
monitor for control （ #: plug and play monitor ） and #: PC-50S are
recognized.
(PC-50S displayÆ)

(3) Select “For near vision”,

Device : NC3 or NV20
Type :E

(4) Touch [OK]

(5) Touch [Yes]

17
5-1.3. Settings in PC-50S.
(1)
(SETUP1) Press [Shift]&[Menu] button, and select
[Settings]_[Chart Settings]

(SETUP2) Click [Settings] icon and

click [Chart Settings].

(2) Select [Chart Software Config.]

(3) Select [Chart Settings] .

18
 (4) Select each item.
*Examination distance(2.5m-6.0m)
*slideshow interval (3-10 secs)
*Size of VA indicator
*Masked chart layout
*mirrored chart
*Language (no need to set)

(5) Touch OK

5-2. PC-50S for SETUP 3

5-2.1. Cabling
Connect DVI cable between PC-50S and computer.

DVI cable

5-2.2. Settings in CV-5000S SETUP3

(1) Start CV-5000PC

19
(2) Click [Settings] and select [Chart Settings]

(3) Select in [For far vision],

Device = PC-50S
Type = Chart A, B, E, F,H
(at your convenience)

Chart monitor selection =

# : Plug and Play Monitor

Select in [For near vision]

Device = NC3/NV20
Type = E

Touch the mark, so that you can see # : Plug and Play Monitor
# : Plug and Play Monitor is recognized.
(PC-50S displayÆ)

20
5-2.3. PC-50S
See 5-1.3

5-3. PC-50S Wireless connection for SETUP 1&2, 3

EZ AIR USB/DVI wireless doc is only confirmed device.
No other manufacturer’s cannot be used.

5-3.1. Connect USB transmitter to USB socket on control box (SETUP 1/2), KB-50S or on PC (SETUP3).

*Install USB driver for EZ Air in case of SETUP3. Control box (SETUP 1/2) is pre-installed with the driver for
EZ Air.

5-3.2. Connect USB doc and PC-50S by DVI cable.

DVI cable

5-3.3. Select [#:Display Link Device].

21
5-4. PC-50 / CC-100 series /ACP-8 / MC-3 (RS-232C)
Please see instruction manual for how to set up ACP-8/MC-3/PC-50.

5-4.1. Connect the chart to ACP/MC port of power supply with serial cable.
For ACP/MC-3 432140006 (RS232C Din8-Din8)
For PC-50 424290061 (RS232C Din8 Dsub9)

（SETUP 1/2）

（SETUP 3）

22
5-4.2. Settings in CV-5000S
(1)
(SETUP1) press [Shift]&[Menu], and
select [Settings]_[Chart Settings]

(SETUP2,3) click [Settings ] and

select [Chart Settings]

(2) select each item in [For far vision]

Device : ACP-8 or MC-3 or PC-50
Type : A, B, F, or H
Interface : RS-232C

5-4.3. in case of PC-50

(1)Turn on PC-50 power.
(2)Press Menu switch No.1 (left) to show [Main Menu].

23
(3)[1. Settings]

(4) Set the distance.

(5)Exit and go to [2.select Advanced Settings].

(6)Select each necessary item.

24
1. Language (not necessary to change)
Selectable from “Japanese” and “English”. Default is “English”.
2. Chart type
Select chart type from “A” “B” “F” “H1”. Default is “F”. this must be the same with the selected chart in CV
system..
3. Remote type
Select type of controller from “Non LCD” “LCD” “KB-50”.
If setting is different in PC-50 and controller, it looks working normal but some of function might not work.

Select “KB-50” in case of using IR emitter with KB-50S/CV-5000S (SETUP 1/2/3).

Non LCD This will be used when Remote Controller of PC-50 is used.
KB-50

4. Mirror (not necessary to change)

Enable or Disable, along the case using mirrored system.
5. RS-232C settings
In case using RS-232C cable, please select “2400bps”.
Not Connecting IR emitter or remote controller is used.
2400bps For wired connection with CV-5000S/CV-5000.
9600bps

(7) Exit the menu.

25
5-5. PC-50 /CC-100 series /ACP-8 / MC-3 (IR emitter)
Please see instruction manual for how to set up ACP-8/MC-3/PC-50.

5-5.1. Cabling
Connect IR emitter to IR port of power supply.
IR emittor 424120005

（SETUP 1/2）

(SETUP3)

26
5-5.2. Settings in CV-5000S
(1) (SETUP1) press [Shift]&[Menu], and
select [Settings]_[Chart Settings]

(SETUP2,3) click [Settings ] and

select [Chart Settings]

(2) Select each item.

Device : ACP or MC-3 or PC-50

Type : A, B, F, H
Interface : IR control CH1-CH4.

z When “IR control” is selected in [Interface], appears on the right side.

Click this and check whether the IR signal and chart device are synchronized via the selected
channel.

5-5.3. In case of PC-50.

See 5-4.3

27
 6. Connection with refraction instruments

CL(Rx)
STD1 format data

Ref (AR)
data

Xml format

9 Data from refraction units are transferred in STD1 format by serial communication and saved in xml format
inside shared folder or default folder of CV-5000S system.
9 KR-1, furthermore, is capable of transferring data directly in xml format by LAN network.
9 Only representative value of Ref / Kerato data are saved.

Control box SETUP1/2 has 3 ports for serial data transfer communication.

COM2 Æ
COM1 Æ

Å COM3
Dsub 9 pins male
Din8 female

SETUP 3 has no port for refraction unit, connect the unit directly to PC.

28
 General information about cables

418120002 RS-232C 5m
(DIN 8 pins male L-shape – D SUB 9 pins female)
424290061 RS-232C 10m
(DIN 8 pins male L-shape – D SUB 9 pins female)
432140006 RS-232C 5m
(DIN 8 pins male L – DIN 8 pins male L)
432140010 RS-232C 10m
(DIN 8 pins male L – DIN 8 pins male L)
RS232C-USB converter cable
(D SUB 9 pins male – USB (A))
Please arrange locally if necessary.

LAN cable (cat 5 / 5e / 6, straight)

Please arrange locally.

6-1. RM/KR-8900 (RS-232C)

6-1.1. RM/KR setting
(1) Power up RM/KR-8900 with holding the menu button
to enter [INITIAL MENU].

(2) Select [ON-LINE]_[DATA FORMAT]_[STD1]

29
 (3) Select [ON-LINE]_[BAUD-RATE]_[9600].
Select [EXIT] to confirm and close.

*in case of KR-8900,

select [ON-LINE]_[OUTPUT DATA TYPE]_[ALL].

(4) Reboot RM/KR-8900 and press the control lever switch.

Then press menu button to enter [SETTING MENU].
(5) Select [OUTPUT DATA]_[YES].
Then select EXIT to confirm and close.

6-1.2. Cabling between RM/KR-8900 and CV power supply box.

1. 418120002 (RM out port to CV COM1/2)
(RM out port to PC)
2. 432140006 (RM to CV COM3)

30
6-1.3. CV-5000S setting
(1) (Setup 1) Press [Shift] & [Menu] button to access the setting screen.

(Setup 2,3) Click [Settings] icon.

(2) Select [Data I/O settings]_[System Configurations]

(3) Select [LAN configuration]

(4) Tick off in “Enable network connection”.

31
 (5) Select [Serial configuration] .

(6) In the blank connection, touch the [▼] button

and select each as follows;

for : [In] AR/Rx data receive

Port No. : COM port number RM/KR is connected.
Baud Rate : 9600
(identical with the baud rate of machine)

To connect the NIDEK refractometer (model: older than 530A),

select “[In] REF data receive (00)”.
To connect the NIDEK refractometer (model: 530A and later), select “[In] REF data receive (01)”.

(7) touch [OK]

6-1.4. Check data transfer RM/KR-8900 Æ CV-5000S

(1) measure objective data in RM/KR-8900
(2) Press [print] button
(3) Check “RS-232C SUCCESS” on the screen.
(4) Press [IN] button on KB-50S.

Click [Data Import] on monitor.

(5) Check the measured power was actually
received.

32
6-2. KR-1 (RS-232C)
6-2.1. KR-1 setting.
(1) Power on KR-1.
(2) Select [Menu]_[Comm]_[Output data]_[All]
Select [Menu]_[Comm]_[STD1]
Select [Menu]_[Baud Rate]_[9600].

6-2.2. Cabling between KR-1 & CV-5000S

1.418120002 (KR out port to CV COM1/2)
(KR out port to PC)
2. 432140006 (KR OUT to CV COM3)

6-2.3. CV-5000S setting

See 6-1.3

6-2.4. Check data transfer KR-1 Æ CV-5000S

(1) measure objective data in KR-1
(2) Press [print] button
(3) Check “RS-232C SUCCESS” on the screen
(4) Press [IN] button on KB-50S

Click [Data Import] on monitor.

(5) Check the measured power was actually
received.

z If patient ID is input on KR-1, ID will be transferred

and shown in Patient ID column.

33
6-3. KR-1 (LAN)
6-3.1. Settings in KR-1
(1) Power up KR-1 and select [Menu]_[LAN]
(2) set each item as follows.

LAN connection ON
XML file output ON
Ref / Kerato data output OFF
Shared folder configuration
¥¥IP address of shared CV
system¥RM
e.g. ¥¥192.168.128.152¥rm
• Shared folder

Default “TOPCON”
Or user name which is otherwise assigned to access shared
• User name
folder.
*please do not tell this information to the customer
Default “CV-5000S” (all capital)
Or password which is otherwise assigned to access the shared
• Password
folder.
*please do not tell this information to the customer
IP properties Fix.
Assign KR-1 IP address to access network with CV-5000S
IP address
e.g. 192.168.128.153

Set the subnet mask.

Subnet mask
e.g. 255.255.255.0

Set the default gateway for the network if necessary.

Default gateway
e.g. 192.168.128.254

34
6-3.2. Cabling
LAN (straight) left LAN port to hub or PC

6-3.3. Setting in CV-5000S

(1)
(Setup 1) Press [Shift] & [Menu] button to access the
setting screen.

(Setup 2,3) Click [Settings] icon.

(2)Select [Data I/O settings]_[System Configurations]

35
 (3) Select [LAN configuration]
(4) Tick in “Enable network connection”

(5) Input IP properties

Input the IP address of CV system which consist network with KR-1.
IP address e.g. 192.168.128.152
*should be identical with the one input for step 6-3.1
Set the subnet mask identical for CV system and KR-1
Subnet mask
e.g. 255.255.255.0
Set the default gateway for the network if necessary.
Default gateway
e.g. 192.168.128.254

4.’ In case of SETUP 3, IP address is retrieved automatically from the Windows network setting.
If there is not any, please input the IP address, Subnet mask, Default gateway in the following.
(Windows XP)
[Control Panels]_[Network] _ [Local Area Connection] _[properties]
(Windows7)
[Control Panels] – [Network and Internet] – [Networks and Sharing Center]
– [Local Area Connection]

36
 IP address should be identical with the one input for step 6-3.1

(6) Touch [Data folder]

(7) Tick in “Use shared folder in CV system” of [ AR data folder configuration]

KR-1 data is saved in pre-installed folder of
CV-5000S system.

*With tick in [Use shared folder in CV system], you

only need to input IP address of CV-5000S
system. Preinstalled folder will be used and
default authentication ID will be active for
accessing the shared folder.
(ID : TOPCON,
Password : CV-5000S)

(8) Input the IP address of CV system which has shared folder

*This must be identical among all networked units.
e.g. ¥¥192.168.128.152

(9) Touch [OK] .

6-3.4. Check data transfer KR-1 Æ CV-5000S

1. Measure data with KR-1
2. Touch Print icon.
3. Press [IN] on KB-50

Click [Data Import] on monitor.

4. Make sure the data coming in AR data.

* If patient ID is input on KR-1,

it will be transferred and shown in
Patient ID column.

37
6-4. TRK-1P (RS-232C)
6-4.1. Settings in TRK-1P
(1) Power up TRK-1P with holding 2nd button from the right
to enter [INITIAL MENU].

(2) select [INITIAL MENU[_[ON-LINE]

Select [ON-LINE]_[OUTPUT DATA TYPE]_[R/K].

Select [ON-LINE]_[DATA FORM]_[STD1]

Select [ON-LINE]_[DATA OUTPUT PORT]_

[RS-232C]

38
 Select [ON-LINE]_[BAUD RATE]_[9600]

6-4.2. Cabling between TRK-1P and CV-5000S

418120002 (RM out port to CV COM1/2)
432140006 (RM to CV COM3)

6-4.3. Settings in CV-5000S

See 6-1.3

6-4.4. Check data transfer TRK-1P Æ CV-5000S

1. measure data with TRK-1P
2. Press print
3. Press [IN] on KB-50S.

Click [Data Import] on monitor.

5. Make sure the data coming in AR Data area.

6-5. CL-200 (RS-232C)

6-5.1. Settings in CL-200

(1) With pressing 2nd right button and power up CL-200
(2) [INITIAL MENU] opens and make sure
[RS232C]_[NORMAL]

39
 (3) [EXIT]

(4) On measurement screen, press [MODE], and press [MENU].

(5) Select [MENU]_[RS232C]_[STD1]

(6) Select [MENU]_[SEQ], and put identification number on CL-200

6-5.2. Cabling between CL-200 and CV-5000S

418120002 (CL OUT port to CV COM1/2, or PC)
432140006 (CL OUT port to CV COM3)

40
6-5.3. Settings in CV-5000S
(1) (Setup 1) Press [Shift] & [Menu] button to access the setting screen.

(Setup 2,3) Click [Settings] icon.

(2)Select [Data I/O settings]_[System Configurations]

(3) Select [LAN configuration]

(4) Tick off in “Enable network connection”.

41
 (5) Select [Serial configuration] .

(6) In the blank connection, select as follows;

For : [In] AR/Rx data receive

Port No. : COM port number CL is connected.
Baud Rate : 2400 (fixed)

*To connect the NIDEK lens meter, select “[In] LensMeter data receive”.

(7) Touch OK

6-5.4. Check data transfer CL-200Æ CV-5000S

(1) Measure eyeglasses or lens with CL-200.
(2) When it comes to “PRINT OK”,
(3) Press [print]
(4) Press [IN] switch on KB-50

Click [Data Import] on monitor.

(5) Make sure the CL-200 data is coming into
Rx Data list.

6-6. EZ-200 (RS-232C)

6-6.1. Settings in EZ-200
(1) Power up EZ-200.
(2) Press [Mode], and [Menu]

42
 (3) Select [MENU]_[RS-232C]_[OUTPUT]
Then select [EXIT] to confirm

(4) Press [Mode] and [Menu]

(5) Select [MENU]_[RS-FORMAT]_[STD1]
Then select [EXIT] to confirm

6-6.2. Cabling between EZ-200 and CV-5000S

418120002 (EZ out port to CV COM1/2, PC)
432140006 (EZ out porty to CV COM3)

6-6.3. Settings in CV-5000S

See 6-5.3

6-6.4. Check data transfer EZ-200 Æ CV-5000S

(1) Measure eyeglasses with EZ-200
(2) After getting the reading press[Print]
(3) Press [IN] switch on KB-50

Click [Data Import] on monitor.

(4) Make sure the reading is set in Rx Data area.

43
7. Output subjective data to PC
General information about cables

418120002 RS-232C 5m
(DIN 8 pins male L-shape – D SUB 9 pins female)
424290061 RS-232C 10m
(DIN 8 pins male L-shape – D SUB 9 pins female)
RS-232C cross
(D SUB 9 pins female - D SUB 9 pins female)
Please arrange locally

RS-232C-USB converter cable (D SUB 9 pins

male – USB (A))
Please arrange locally if necessary

‹ LAN cable (cat 5 /5e/ 6 straight)

7-1. IMAGEnetR4

STD1 format
RS232C cable MDR

44
7-1.1. Cabling between CV-5000S and PC
418120002 (CV COM3 to PC serial)
D SUB-DSUB (cross) (CV COM1/2 to PC serial)

7-1.2. Settings in CV-5000S

(1) (Setup 1) Press [Shift] & [Menu] button to access the setting screen.

(Setup 2,3) Click [Settings] icon.

(2)Select [Data I/O settings]_[System Configurations]

(3) Select [LAN configuration]

(3) Tick off in “Enable network connection”.

45
 (4) Select [Serial configuration] .

(5) Select one of blank connection and set as follows.

*for : [I/O] Database connection
*Port No. : COM1-3 which is connected to IMAGEnetPC
*Baud Rate : 2400 bps (fixed)

(6) Click OK
(7) (SETUP1) Go to [Function Settings]_[Print Switch]_Action,
Please select [Data export] or [Printout & data export]

(8) Touch OK
7-1.3. IMAGEnetR4 and MDR
(1)Install Prerequisites
*Prerequisites must be Ver.4.0.
(2)Install IMAGEnet
* IMAGEnet R4 must be later than Ver.4.13.
(3)Install “Multi Data Receiver” (MDR).

46
7-1.4. Settings in MDR
(1)Required file
File Detail
CV5000-STD1-InPlugin.dll Interface file for receiving CV-5000 (RS-232C) data

Please find the above file in C¥Program Files¥TOPCON¥MDR¥Plugin.

If it does not exist, please copy and paste.

(2) Start [Multi Data Receiver Configuration] ([MdrSetup.exe],

(3) [CV-5000 STD1 Plugin] shall be listed in [Communication Plug-in] window.

(4) Select [CV-5000 STD1 Plugin]

(5) Click [Settings]

47
 (6) in [Setup] dialog, input [COM PORT] and click [OK]

* Select [COM Port] in the pulldown list.

(7) Select [ExamData Plugin]

(8) Click [Setting]
(9) in [General] tab, input [Database] information.

48
 (10) in [Out plugin], tick in [Show Register Window].

* Please see “MDR setup manual” for detail.

7-1.5. check data transfer CV-5000S Æ IMAGEnetR4

(1) Check MDR is at waiting-status, and pop-up
window in open.

(2) Measure with CV-5000S

(3) (SETUP1) Press Print switch

(SETUP2) Click [Data Export] icon. (*register this icon on tool bar)

49
(4) See MDR windows received data.
(date & time only)

(5) Register with patient ID

(6) Open with IMAGEnetR4.

50
7-2. I-base

7-3. XML format

.xml file export will be available in next version.
Only LAN connection realizes .xml format export.
7-3.1. Connect LAN cable to PC (SETUP3) or control box (SETUP1/2) at always left side port.

7-3.2. Format can be selectable among “.xml file”, “export file Ver.1.00” and “export file ver.2.14”.

7-3.3. Settings as follows.

1.[Settings]_[Data IO settlings]_[System configurations]_[Data file configurations]

2.Select “File Format Version”.
3.Tick in “Use pre-installed shared folder” if using the shared folder in CV-5000S system.
If using shared folder at other path, input the shared folder IP for the exported file

51
8. Network system 1
To add a new CV-5000S (SETUP 1/2/3) to existing CV-5000 system and RM/CL
8-1. Data flow
¾ RM/KR/CL data will be sent to CV-5000/CV-5000S in STD1 format.
¾ CV-5000 and CV-5000S received same data list sent via RM/KR/CL.
¾ If RM/KR/CL has patient ID capability, patient ID will be sent to CV-5000 as well.
¾ Subjective data will not be saved.
¾ Shared folder setting is not required. In case of one, non-networked CV-5000S is used, data folder
inside CV-5000S is automatically used.
¾ It is possible to set the period to delete and refresh the RM/CL data saved in shared folder.

CV-5000 (1) CV-5000S (2)

Shared
folder (AR)

(1) (2) Shared

RS-232C RS-232C folder (Rx)

CV-5000S (3) CV-5000 (4)

(3)
(4)
RS-232C
RS-232C

Shared Shared
folder (Rx) folder (AR)
8-2. Cabling
(1) 432140005 DIN8 DIN8 (RM/CL to CV RM )
(2) 418120002 Din8-DSUB9(CV COM to CV COM1/2)
432140005 DIN8 DIN8 (CV COM to CV COM3) * cannot be used for SETUP3
(3) 432140005 DIN8 DIN8 (RM/CL to CV COM3 )
418120002 Din8-DSUB9 (RM/CL to CV COM1/2)
(4) 432140005 DIN8 DIN8 (CV COM3 to CV RM)
418120002 Din8-DSUB9(CV COM1/2 to CV RM)

52
8-3. Settings
8-3.1. RM/KR/CL Æ (STD1).
Please see RM/KR(6-1.1), KR-1(6-2.1),TRK-1P(6-4.1), CL-200(6-5.1), EZ-200(6-6.1).

8-3.2. RM/KR Æ CV-5000 (1) Æ CV-5000S (2)

CV-5000(1) Set the dipswitch of power supply box as below.
DIP switch 1. 1 OFF
DIP switch 1. 2 ON
DIP switch 1. 3 OFF
DIP switch 1. 4 ON (9600)
*OFF (2400) to CV to RM/KR

DIP switch 2 1 ON
DIP switch 2 2 ON
DIP switch 2 5 OFF
DIP switch 2 6 OFF

For the other connection, please see the CV-5000 DIP/SW setting manual.

8-3.3. CV-5000(1)Æ CV-5000S(2)

(1)(SETUP1) Press the [Shift] and [Menu]

(SETUP2,3) click [settings] icon.

(2)[Data I/O settings] _ [System configurations]

(3)[Serial config.]

53
 (4)In any of blank connection, touch the [▼] button and select each item.
“for” : “[In] AR/Rx data receive”.
Port : Port number which (old) CV-5000 is connected.
BaudRate : 2400bps or 9600 bps.
(same baud rate selected for step 8-3.2)

8-3.4. RM/KR/CL ÆCV-5000S(3)Æ CV-5000(4)

1. (SETUP1) Press the [Shift] and [Menu]

(SETUP2,3) click [settings] icon.

1. [Data I/O settings] _ [System configurations]

3. [Serial config.]

4. In any of blank connection, touch the [▼] button and select

“for” : “[In] AR/Rx data receive”.
Port : Port number which RM/KR/CL is connected.
BaudRate : 2400bps or 9600 bps.
(same baud rate set in the machine)

* In case several machines are connected,

create connection for each.

54
 3. In any of blank connection, touch the [▼] button and select each item.
“for” : “[Out] RM/CL data transfer”.
Port : Port number which (old) CV-5000 is connected.
BaudRate : 2400bps or 9600 bps.

5. Click OK and exit the settings.

9. Network system 2
To have several CV-5000S (System 1 or 2) and CL. KR-1
9-1. Data flow
RM/KR/CL CV-5000S(1) CV-5000S (2)

(1)
RS-232C
STD1

(2) LAN (2) LAN (2) LAN

XML XML XML Shared Folder
Ref data
CL data

¾ Shared folder is pre-installed in CV-5000S system. In the above picture, supposing shared
folders are the one preinstalled CV-5000S(2).
¾ As far as they are networked, Ref/CL data saved in shared folder can be retrieved any time.
¾ It is possible to set the period to delete and refresh the RM/CL data saved in shared folder.
¾ Subjective data is not saved, they will be printed out or discarded. (since next version, subjective
data will be export in .xml format.

55
 ¾ If patient ID is input in KR/RM, patient ID will be output together with data.

9-2. Cabling
(1) 432140005 DIN8 DIN8 (RM/CL to CV COM3 ) or
418120002 DIN8-Dsub9 Din8-DSUB9(CL to CV COM1/2)
(2) LAN

9-3. Settings
9-3.1. RM/KR/CL Æ (RS-232C setting)
They should output data in STD1 format.
Please see RM/KR(6-1.1), KR-1(6-2.1),TRK-1P(6-4.1), CL-200(6-5.1), EZ-200(6-6.1).

9-3.2. KR-1 Æ (LAN )

Please see 6-3.1.
In Menu_LAN_Sharedfolder, input IP address of CV-5000S(2)
¥¥ IP address of shared CV 5000S(2)¥rm
e.g. ¥¥ 10.140.19.112¥rm

9-3.3. RM/KR ÆCV-5000S (1) ⇔ Shared folder

1. (SETUP1) Press [Shift] and [Menu]

(SETUP2) click [settings] icon.

2. [settings]_[Data I/O settings]_[System configuration]

3. [Serial config.]

4. In any of blank connection, touch the [▼] button and select each item.

“for” : “[In] RM/CL data receive”.

Port : Port number which RM/KR/CL is connected.
BaudRate : 2400bps or 9600 bps.

(same baud rate set in the machine)

* In case several machines are connected,

create connection for each.

56
6. [LAN Configuration]
7. Tick in [Enable Network connection] and input IP address of CV-5000S(1)

9. [Data Folder]
10. if RM/KR is used,
Tick in [use shared folder in CV system] in AR data folder configuration.
Input IP address of CV-5000(2)
Tick in [use shared folder in CV system] in Rx data folder configuration.
Input IP address of CV-5000(2)

9-3.4. CV-5000S (2) & Shared folder

1. (SETUP1) Press [Shift] and [Menu]

(SETUP2) Click [settings] icon.

2. [Settings]_[Data I/O settings]_[System configuration]

57
3. [LAN Configuration]
4. Tick in [Enable Network connection] and
Input IP address of CV-5000S(2)

6. [Data Folder]
7. if RM/KR is used,
Tick in [use shared folder in CV system] in AR data folder configuration.
Input IP address of CV-5000(2)
Tick in [use shared folder in CV system] in Rx data folder configuration.
Input IP address of CV-5000(2)

8. Click OK.

58
10. Network system 3
To have several CV-5000S (Setup 1/2 and Setup 3)
10-1. Data flow diagram
Shared folder RM/KR/CL
CV-5000S (1) CV-5000S (2) (1)
(AR/Rx)
RS-232C
STD1

(2)

(2)
LAN XML

9 Shared folder must be on CV-5000(1) SETUP3.

9 CV-5000S(1) must not have user account named or including “shared folder ID” (=TOPCON)
9 Shared folder must be on SETUP3

9 RM/K/CL data sent via RS-232C is once received at CV-5000S(2), then saved in shared folder.
9 KR-1 data if sent via LAN is saved directly in shared folder.
9 RM.KR.CL data are shared by CV-5000S(1) and (2).
9 Subjective data is not saved must be printout. (can be exported in file since next version)

10-2. Cabling
(1) 432140005 DIN8 DIN8 (RM/CL to CV COM3 ) or
418120002 DIN8-Dsub9 Din8-DSUB9 (CL to CV COM1/2)
(2) LAN

10-3. Settings
10-3.1. RM/KR/CL Æ RS-232C setting)
They should output data in STD1 format.
Please see RM/KR(6-1.1), KR-1(6-2.1),TRK-1P(6-4.1), CL-200(6-5.1), EZ-200(6-6.1).

59
10-3.2. KR-1 Æ (LAN )
Please see 6-3.1.
In Menu_LAN_Sharedfolder, input IP address of CV-5000S(1)
¥¥ IP address of shared CV 5000S(1)¥rm
e.g. ¥¥ 10.140.19.112¥rm

10-3.3. CV-5000S(1)

1.Enable “Guest” account.

[My Computer]_[Control Panels]_[Administrative Tools]_[Computer Management]_
[Local Users and Groups]_[Users]_[Guests]
Righclick and select [Properties]
If “Account is disabled” is ticked, remove tick.

This is to permit the network access of another computer (=Guest).

2. Open the PC to networking access

[My Computer]_[Control Panels]_[Administrative Tools]_[Security Settings]_[Local Policies]_
[User Rights Assignment]_[Deny access to this computer from the network].
If “guest” exists, right click and select properties. Remove “Guest.

60
3. If it is Windows 7, turn off “password protected sharing”.
[My Computer]_[Control Panels]_[Network and Sharing center]_[Advanced Sharing settings]
_[Password protected sharing].

4.

61
10-3.4. CV-5000S(1) & Shared folder

1. Click [settings] icon.

2. [Settings]_[Data I/O settings]_[System configuration]

3. [LAN Configuration]
4. Tick in [Enable Network connection] and check IP address of CV-5000S(1)
IP address is automatically generated from Windows network setting.

See 8-3.2 5’.

6. [Data Folder]
7. if RM/KR is used,
Tick in [use shared folder in CV system] in AR data folder configuration
Input IP address of CV-5000(1)
Tick in [use shared folder in CV system] in Rx data folder configuration.
Input IP address of CV-5000(1)

8. Click OK.

62
10-3.5. RM/KR ÆCV-5000S(2) Å Æ Shared folder

1. (SETUP1) Press [Shift] and [Menu] , (SETUP2) click [settings] icon.

2. [settings]_[Data I/O settings]_[System configuration]

3. [Serial config]

4. In any of blank connection, touch the [▼] button and select each item.

“for” : “[In] RM/CL data receive”.

Port : Port number which RM/KR/CL is connected.
BaudRate : 2400bps or 9600 bps.

* In case several machines are connected,

create connection for each.

6. [LAN Configuration]
7. Tick in “Enable Network connection” and input IP address of CV-5000S(2)

63
9. [Data Folder]
10. if RM/KR is used,
Tick in [use shared folder in CV system] in AR data folder configuration
Input address of CV-5000(1)
Tick in [use shared folder in CV system] in Rx data folder configuration
Input IP address of CV-5000(1)

11. Click OK

11. Network system 4

System 3 & system 3
11-1. Data flow Shared folder RM/KR/CL
CV-5000S(2)
CV-5000S(1) (AR/Rx)

(1)
(2)
RS-232C
LAN
STD1
xml

Practice’s network

9 Shared folder can be on network, or can be the preinstalled folder in either CV-5000S.
9 RM/K/CL data sent via RS-232C is once received at CV-5000S(2), then saved in shared folder.
9 KR-1 data if sent via LAN is saved directly in shared folder.

64
9 RM.KR.CL data are shared by CV-5000S(1) and (2).
9 Subjective data is not saved, thus must be printout. (can be exported in file since next version)
9 CV-5000S(1) must not have user account named “TOPCON”.
9 Any of user/log in ID and password of CV-5000S(1) PC nor CV-5000S(2) PC should not include the
shared folder ID (=TOPCON)
(in September, CV-system will access to shared folder regardless of login user. )

11-2. Cabling
(1) 432140005 DIN8 DIN8 (RM/CL to CV COM3 ) or
418120002 DIN8-Dsub9 Din8-DSUB9(CL to CV COM1/2)
(2) LAN

11-3. Settings

11-3.1. CV-5000S (1)

1.Enable “Guest” account.
[My Computer]_[Control Panels]_[Administrative Tools]_[Computer Management]_
[Local Users and Groups]_[Users]_[Guests]
Righclick and select [Properties]
If “Account is disabled” is ticked, remove tick.

This is to permit the network access of another computer (=Guest).

5. Open the PC to networking access

[My Computer]_[Control Panels]_[Administrative Tools]_[Security Settings]_[Local Policies]_

65
 [User Rights Assignment]_[Deny access to this computer from the network].
If “guest” exists, right click and select properties. Remove “Guest.

6. If it is Windows 7, turn off “password protected sharing”.

[My Computer]_[Control Panels]_[Network and Sharing center]_[Advanced Sharing settings]
_[Password protected sharing].

7.

66
 4. Start CV-5000S PC software and Click [settings] icon.

5. [Settings]_[Data I/O settings]_[System configuration]

6. [LAN Configuration]
7. Tick in [Enable Network connection] and check IP address of CV-5000S(1)

IP address is automatically generated from Windows network setting.

See 8-3.2 5’.

6. [Data Folder]
7. if RM/KR is used,
Tick in [use shared folder in CV system] in [AR data folder configuration]
Input IP address of CV-5000(1)
Tick in [use shared folder in CV system] in Rx data folder configuration.
Input IP address of CV-5000(1)

8. Click OK.

67
11-3.2. RM/KRÆ CV-5000(2)Å Æ Shared folder

1. Start CV-5000S PC software and click [settings] icon.

2. [Settings]_[Data I/O settings]_[System configuration]

3. [LAN Configuration]
4. Tick in [Enable Network connection] and check IP address of CV-5000S(2)
IP address is automatically generated from Windows network setting.

See 8-3.2 5’.

6. [Data Folder]
7. if RM/KR is used,
Tick in [use shared folder in CV system] in AR data folder configuration.
Input IP address of CV-5000(1)
Tick in [use shared folder in CV system] in Rx data folder configuration.
Input IP address of CV-5000(1)

8. [Serial config]

68
9. In any of blank connection, touch the [▼] button and select each item.

“for” : “[In] RM/CL data receive”.

Port : Port number which RM/KR/CL is connected.
BaudRate : 2400bps or 9600 bps.

5. Click OK

11-3.3. RM/KR/CL Æ(RS-232C setting)

They should output data in STD1 format.
Please see RM/KR(6-1.1), KR-1(6-2.1),TRK-1P(6-4.1), CL-200(6-5.1), EZ-200(6-6.1)

11-3.4. KR-1 Æ (LAN )

Please see 6-3.1.
In Menu_LAN_Sharedfolder, input IP address of CV-5000S(1)
¥¥ IP address of shared CV 5000S(1)¥RM
e.g. ¥¥ 10.140.19.112¥rm

12. Network system 5

System 1, CL, KR, IMAGEnetR4
12-1. Data flow
IMAGEnetR4
CV-5000S
RM/KR/CL RM/KR/CL database
(KR-1)
(3)
RS-232C
STD4

(1) (2)
RS232C RS-232C
STD1 STD1

9 CV-5000S receives representative value from RM/KR/CL and send subjective data to IMAGEnetR4
69
 together with RM/KR/CL data.
9 In order to keep KR-1 all data (including peripheral kerato data), it must be linked directly with
IMAGEnetR4, via RS-232C cable and in STD4 format.

12-2. Cabling
(1) 418120002 DIN8-Dsub9 Din8-DSUB9(CL to CV COM1/2)
(2) 418120002 DIN8-Dsub9 Din8-DSUB9(CV COM3 to PC serial )
or DSUB DSUB (cross) locally arrange (CVCOM1/2 to PC serial)
(3) 418120002 DIN8-Dsub9 Din8-DSUB9(CV COM3 to PC serial )

Serial –USB conversion cable is recommended.

12-3. setting
12-3.1. RM/KR/CL Æ (RS-232C)
They should output data in STD1 format. (KR-1 can be STD4)
Please see RM/KR(6-1.1), KR-1(6-2.1),TRK-1P(6-4.1), CL-200(6-5.1), EZ-200(6-6.1)

12-3.2. RM/KR/CL ÆCV-5000SÆIMAGEnetR4

1. (SETUP1) Press [Shift] and [Menu] , (SETUP2) click [settings] icon.

2. [settings]_[Data I/O settings]_[System configuration]

3. [Serial config]

4. In any of blank connection, touch the [▼] button and select each item.
“for” : “[In] RM/CL data receive”.
Port : Port number which RM/KR/CL is connected.
BaudRate : 2400bps or 9600 bps.

70
5. Select one of blank connection and set as follows.
*for : [I/O] Database connection
*Port No. : COM1-3 which is connected to IMAGEnetPC
*Baud Rate : 2400 bps

6. [LAN Configuration]
7. Tick off in [Enable network connection]

10.Click OK

11.(SETUP1) Go to [Function Settings]_[Print Switch]_Action,

Please select [Data export] or [Printout & data export]

71
 12.Touch OK

12-3.3. IMAGEnetR4
1.create CV-5000 communication plug-in
See. 7-1.3,7-1.4.

2. create KR-1 communication plug-in

*Communication Plug-in*
Select “KR-1 STD4 Plugin”
Select COM NO. COMPort No. which KR-1 is connected。
Select Baud Rate : 2400/9600 (identical with the machine setting)
Select Flow Control : RTS/CTS

*Out Plugi-in*
Same as CV-5000S

13. Network system 6

To have central server, IMAGEnet station, CV-5000S/KR-1
IMAGEnet(1)
13-1. DATA FLOW
(2) RS232C
(2) RS232C
RM/KR/CL CV-5000S(1) STD1 CV-5000S(2)
RM/KR/CL STD1
(KR-1)
CV data to MDR

(1) LAN
(1) LAN (1) LAN (1) LAN
RM XML
XML (RM/CL) XML (RM/CL) CV data (to IMAGEnet)

IMAGEnetR4 (1) LAN

database Images to IMAGEnet

Shared folder
RM/CL

IMAGEnet(2)
Fundus images etc

72
9 KR-1 data will be saved in shared folder and not directly saved in IMAGEnet.
9 CL-200 data will be saved in shared folder and not directly saved in IMAGEnet.
9 CV-5000(1) retrieves any RM/CL data from shared folder, and its subjective data is not saved.
9 CV-5000(2) retrieves any RM/CL saved in shared folder and sends subjective data to IMAGEnet (1).
9 Subject data (STD1 format) contains RM/CL data, and subjective data, and can be reviewed on
IMAGEnetR4.

13-2. Cabling
(1) LAN
(2) 418120002 DIN8-Dsub9 Din8-DSUB9 (CL OUT – CV COM1/2)
432140005 DIN8 DIN8 (RM/CL to CV COM3 )
(3) 418120002 DIN8-Dsub9 Din8-DSUB9 (CV COM3 –PC serial)
DSUB DSUB (cross) locally arrange (CVCOM1/2 to PC serial)

13-3. Settings
13-3.1. Server
1. Check IP address of server.
2. Create shared folder in server for RM/CL data (e.g. “rm” folder, “cl” folder).

13-3.2. RM/KR/CLÆ CV-5000(1)

They should output data in STD1 format.
Please see RM/KR(6-1.1), KR-1(6-2.1),TRK-1P(6-4.1), CL-200(6-5.1), EZ-200(6-6.1).

13-3.3. KR-1 Æ shared folder

1. Please see 6-3.1

2. Input IP address of server.

Shared folder configuration
¥¥ server IP address (shared folder)¥rm
• Shared folder e.g. ¥¥192.168.128.152¥rm
(must be the identical name of created folder in 13-3.1)
user name which is permitted to access shared folder.
• User name *please do not tell this information to the customer
*Be sure to no login user ID does not contain this user name.
password which can access the shared folder.
• Password
*please do not tell this information to the customer

73
13-3.4. RM/KR/CL ÆCV-5000S (1) Å Æ shared folder

1. Press [Shit] & [Menu]. Click [settings] icon.

2. [Settings]_[Data I/O settings]_[System configuration]

3. [LAN Configuration]
4. Tick in [Enable Network connection]
and check IP address of CV-5000S(1)

6. [Data Folder]
7. if RM/KR is used,
Tick off [use shared folder in CV system] in AR data folder configuration.
*Input IP address of server¥rm
(must be the identical name and path of created folder in 13-3.1)
*Input user name which is permitted to access this shared folder.
*Input password assigned to the above user name.

Tick off [use shared folder in CV system]

in Rx data folder configuration.
Likewise
*Input IP address of server¥cl
(must be the identical name and path of created
folder in 13-3.1)
*Input user name which is permitted to access this
shared folder.
*Input password assigned to the above user
name.

74
8. [settings]_[Data I/O settings]_[System configuration]

9. [Serial config]

10. In any of blank connection, touch the [▼] button and select each item.
“for” : “[In] RM/CL data receive”.
Port : Port number which RM/KR/CL is connected.
BaudRate : 2400bps or 9600 bps.

13-3.5. Shared folder ÆCV-5000S (2)Æ IMAGEnetR4

1. Press [Shit] & [Menu]. Click [settings] icon.

2. [Settings]_[Data I/O settings]_[System configuration]

3. [LAN Configuration]
4. Tick in [Enable Network connection] and
check IP address of CV-5000S(1)

75
5. [Data Folder]

6. if RM/KR is used,
Tick off [use shared folder in CV system] in AR data folder configuration.
*Input IP address of server¥rm
(must be the identical name and path of created folder in 13-3.1)
*Input user name which is permitted to access this shared folder.
*Input password assigned to the above user name.

Tick in [use shared folder in CV system]

in Rx data folder configuration.
*Input IP address of server¥cl
*Input user name
*Input password.

7. Select [Serial configuration] .

8.Select one of blank connection and set as follows.

*for : [I/O] Database connection
*Port No. : COM1-3 which is connected to IMAGEnetPC
*Baud Rate : 2400 bps

9.Click OK

76
10.(SETUP1) Go to [Function Settings]_[Print Switch]_Action,
Please select [Data export] or [Printout & data export]

(11) Touch OK

13-3.6. CV-5000(S) ÆIMAGEnet (1)

Please see 7-1.3,7-1.4.

13-3.7. IMAGEnet (2)

Set up IMAGEnet R4 as required.

14. Details of setting menu

Please see instruction manual.

77
15. Customizing pictures and movies (PC-50S only)
PC-50S enables to add still images, still images for slideshow and movies that are provided by the
user.

[Capability]
z Maximum 20 (JPG) of both still images and still images for slideshow.
z Maximum 20 (BMP) still images, which are displayed on KB-50S.
z Maximum 2 (WMV) movies.

[File format and filename requirements]

The format of the still image file and movie file is restricted as mentioned below.
Vertical/ Filenam Others
Kind Type horizontal e
size Ref/CL data
Displayed in the largest size as the
Still JPE 01.jpg -
Optional ratio of vertical and horizontal size is
image G 20.jpg kept.
Displayed in the largest size as the
Slidesho JPE 01.jpg -
Optional ratio of vertical and horizontal size is
w G 20.jpg kept.
The video type must be the WMV
encoded by CODEC Windows
Media Video 7 - 9.
Bit rate is max. 10Mbps and frame
rate is max. 30fps.
01.wmv To play back a movie smoothly,
Max.
Movie WMV - KB-50S must be connected to
1280×1024 02.wmv PC-50S through DVI cable.
In the CV system of the personal
computer type, sometimes the
playback of movie is not smooth due
to the specification of the used
personal computer.
The filename number must be the
same as the filename number of the
still image to which this still image
for KB-50S is related.
Remarks:
This function is provided for the
following purpose: the user can
check the far and near visions that
Still 01.bmp
Fixed at are as similar to those in the real
image for BMP -
800×600. world as possible by using still
KB-50S 20.bmp images together with PC-50S. So,
the still image for near vision must
be displayed in almost the real-thing
size.
For this reason, this function is
invalid in the CV system of the
mouse type/personal computer type
where the monitor size is not fixed.

[How to register]
Carry out registration as mentioned below.

78
1. Make folders under USB memory in the following configuration and save the files in the
folders.

Folder Explanation
PC50S_UC Make this folder under the USB memory. This folder
will contain all the folders.
Movie Make this folder under the “PC50S_UC” folder. Save
the movie file in this folder.
Still Make this folder under the “PC50S_UC” folder. This
folder will contain the still images.
KB50S Make this folder under the “Still” folder. The BMP
images are displayed on KB-50S for the still images
displayed on PC-50S. Save the file of these BMP
images in this folder.
Selective Make this folder under the “Still” folder. Save the file of
the JPEG images to be displayed on slideshow in this
folder.
Slide Make this folder under the “Still” folder. Save the file of
the JPEG still images to be displayed on PC-50S in this
folder.
2. Connect the USB memory, which has been arranged in Step 1, to the CV system. Then,
start the CV system.
Still images and movies are not captured into the system but are read directly from the USB
memory. So it is necessary to connect the USB memory to the CV system when using this
added function.
3. Press the [Shift] and [Menu] switches to access the setting screen. Select “Chart settings”
and then “Chart Page registration”.

79
 4. Register the icons to access still image, slideshow and movie into the chart page from the
chart icon list according to the files saved in the USB memory.
Icon Explanation
These icons are used to access the still images saved
in the “Selective” folder. The number on each icon
～ corresponds to the number in the filename.
This icon is used to display the still images in the
“Slide” folder in turn as slideshow.
These icons are used to access the movies saved in
the “Movie” folder. The number on each icon
～ corresponds to the number in the filename.
5. After finishing the above registration, return to the test screen and check if the playback of
the still images, slideshow and movies is performed.

Addition of the binocular function test chart with black background

You can select the binocular function test charts with black background, which are shown below, in
each type of PC-50S.

B(F)/(M)

D3

D5

H1

To use these charts, press the [Shift] and [Menu] switches to access the setting screen.
Select “Chart settings” and then “Chart Page registration”. Register the above charts in the chart
list to the chart page.

16. Export and import settings with USB memory

Output of setting
Perform the following operations on the CV system where the setting should be output.
1. Press the [Shift] and [Menu] switches to access the setting screen.
2. Touch the [Update] button.
3. Touch the [Config. copy] button among the function buttons.
4. Connect the USB memory to the CV system.
The [Export configurations] button will be flickering. Please wait utill “Export configuration” button is
lighting without flickering.
Touch this button.

80
 The output is finished.
If you move or delete the output file out of the USB memory, the setting data cannot be re-input our
uploaded through this USB memory. Be careful.

Input of setting
Perform the following operations on the CV system where the setting should be input.
1. Press the [Shift] and [Menu] switches to access the setting screen.
2. Touch the [Update] button.
3. Touch the [Config. copy] button among the function buttons.
4. Connect the USB memory saving the setting data of the CV system, and the [Import configurations]
will be flickering. Please wait until [Import configurations] button is lighting without flickering.
Touch this button.
5. To make the setting valid, restart the CV system.
The input of setting is finished.
The setting items shown below are not copied. Be careful.
• Date setting
• Time setting
• Next data number
• Far point vision – Device
• Far point vision – Type
• Far point vision - Interface/Chart monitor selection
• Near chart – Device
• Near chart – Type
• IP properties
• Serial configuration - Connection 1
• Serial configuration - Connection 2
• Serial configuration - Connection 3
• Serial configuration – Connection 4

17. Update KB-50S

1. Using the universal personal computer, prepare the install USB memory.
Copy installers from the install CD to the USB memory.
The install CD has “Main Installer_E” folder and “Main Installer_J” folder. “Main Installer_E”
contains the install set for export and “Main Installer_J” contains the install set for Japan.
Open the proper folder. From it, copy the “CV5000_Updater” folder to the route of USB memory.
2. On the KB-50S where you want to perform updating, press the [Shift] and [Menu] switches to access
the setting screen.
3. Touch the [Update] button.
4. Connect the install USB memory to the CV system, and the [Start] button is valid. Touch this
button.
5. Two or more installers are activated in order. Press the [OK] button for each of them to perform
update.

81
6. When update for all the installers is finished, the message instructing to restart the system is
displayed. Check that this message is displayed and then restart the system.

End

82