DESCRIPTION/SUGGESTED SPECIFICATIONS

Sleeve Type Anchors—

SPECIFIED FOR ANCHORAGE INTO CONCRETE, GROUT-FILLED CONCRETE BLOCK,

Dynabolt® HOLLOW CONCRETE BLOCK AND BRICK

Sleeve type anchors feature a split expansion sleeve over a threaded stud bolt body

Sleeve Anchors Dynabolt

and integral expander, nut and washer.
Anchors are made of Plated Carbon Steel, or Type 18-8 Stainless Steel.
Masonry

Versatile, Sleeve Anchors should be installed with carbide tipped hammer drill bits made in
Anchor accordance to ANSI B212.15-1994.

Medium-Duty Anchors are tested to ASTM E488 criteria.

Sleeve Anchor ADVANTAGES

n Anchor diameter equals hole diameter n Heavy-loading capacity
n Available in hex head and three other head styles n Preassembled for faster, easier installations
n Available 1/4 - 3/4” diameter up to 6-1/4” length n Dynabolt can be installed through object to
n Zinc plated carbon steel and 304 stainless steel be fastened
n Provides full 360° hole contact over large area n Sleeve design improves holding power
and reduces concrete stress n No pre-spotting of holes necessary

Available Head Styles

Full range of head style, corrosion protection, and sizes makes the
Dynabolt Sleeve the right product for almost any application.

Phillips Flat Head Hex Nut

(FS) (HN)

INSTALLATION STEPS
1.Use a carbide tipped drill 2. Insert assembled 3.Expand anchor
Dynabolt bit whose diameter is equal anchor through fix- by tightening nut
Hex Nut Sleeve Anchor to the anchor. See Chart to ture and into hole so or head 2 to 3
determine proper size bit for that washer or head turns.
anchor used. Dnll hole to any is flush with materi-
depth exceeding minimum als to be fastened.
embedment. Clean hole.

APPROVALS/LISTINGS APPLICATIONS
Meets or exceeds U.S. Government G.S.A. Specification A-A-1922A
(Formerly GSA: FF-S-325 Group II, Type 3, Class 3)
Factory Mutual

Electrical junction boxes are common The Dynabolt Sleeve anchor works
applications for the Dynabolt Sleeve well in hollow materials like brick and
anchor because it works well in solid block. It is available in zinc-plated
concrete, concrete block, and brick. carbon steel and 304 stainless steel.
It is also available in several finished
head styles.

Call our toll free number 800-848-5611 or visit our web site for the most
current product and technical information at www.itwredhead.com 85
 SELECTION CHART
Dynabolt
Carbon Steel w/Zinc Plating
MAX. THICKNESS OF
ANCHOR DIA. EFFECTIVE ANCHOR LENGTH* BOLT DIA. / MIN. EMBEDMENT MATERIAL TO BE FASTENED QTY/WT PER QTY/WT PER
& DRILL BIT THREADS PER BOX MASTER CTN
HEAD STYLE PART NO. SIZE in. (mm) INCH in. (mm) in. (mm) qty / lbs. qty / lbs.
HN-1614 5/16" 1-1/2 (38.1) 1/4" / 20 1-1/4 (31.8) 1/4 (6.4) 100 / 4.0 1000 / 41
HN-3817 3/8" 1-7/8 (47.6) 5/16" / 18 1-1/2 (38.1) 3/8 (9.5) 50 / 3.5 500 / 36
HN-3830 3 (76.2) 5/16" / 18 1-1/2 (38.1) 1-1/2 (38.1) 50 / 4.9 400 / 40
HN-1222 1/2" 2-1/4 (57.2) 3/8" / 16 1-7/8 (47.6) 3/8 (9.5) 25 / 3.3 250 / 34
Hex Nut HN-1230 3 (76.2) 3/8" / 16 1-7/8 (47.6) 1-1/8 (28.6) 25 / 4.0 200 / 33
HN-1240 4 (101.6) 3/8" / 16 1-7/8 (47.6) 2-1/8 (54.0) 25 / 5.3 200 / 44
HN-5830 5/8" 3 (76.2) 1/2" / 13 2 (50.8) 1 (25.4) 25 / 7.0 150/ / 46
HN-5842 4-1/4 (108.0) 1/2" / 13 2 (50.8) 2-1/4 (57.2) 10 / 3.9 100/ / 41
HN-3440 3/4" 4 (101.6) 5/8" / 11 2-1/4 (57.2) 1-3/4 (44.5) 5 / 3.2 50/ / 33
FS-3840 3/8" 4 (101.6) 5/16" / 18 1-1/2 (38.1) 2-1/2 (63.5) 50 / 5.3 400 / 44
Phillips (head dia. .722)
FS-3850 5 (127.0) 5/16" / 18 1-1/2 (38.1) 3-1/2 (88.9) 50 / 5.6 300 / 40
Flat Head
FS-3860 6 (152.4) 5/16" / 18 1-1/2 (38.1) 4-1/2 (114.3) 50 / 8.0 300 / 48
* Phillips flat head uses a standard 80°– 82° counter sink.

*Effective Anchor Length

(FS)
Typical Applications—Shelf ledgers, electrical boxes, conduit
Environment—Interior (non-corrosive) A
Level of Corrosion—Low

(HN)

SELECTION CHART
Dynabolt
304 Stainless Steel
MAX. THICKNESS OF
ANCHOR DIA. EFFECTIVE ANCHOR LENGTH BOLT DIA. / MIN. EMBEDMENT MATERIAL TO BE FASTENED QTY/WT PER QTY/WT PER
& DRILL BIT THREADS PER BOX MASTER CTN
HEAD STYLE PART NO. SIZE in. (mm) INCH in. (mm) in. (mm) qty / lbs. qty / lbs.
SHN-3817 3/8" 1-7/8 (47.6) 5/16" / 18 1-1/2 (38.1) 3/8 (9.5) 50 / 3.5 500 / 36
Hex Nut SHN-1222 1/2" 2-1/4 (57.2) 3/8" / 16 1-7/8 (47.6) 3/8 (9.5) 25 / 3.3 250 / 34
SHN-1240 4 (101.6) 3/8" / 16 1-7/8 (47.6) 2-1/8 (54.0) 25 / 5.3 200 / 44

Phillips SFS-3826 3/8" 2-7/8 (73.0) 5/16" / 18 1-1/2 (38.1) 1-3/8 (34.9) 50 / 3.8 500 / 40
Flat Head SFS-3840 4 (101.6) 5/16" / 18 1-1/2 (38.1) 2-1/2 (63.5) 50 / 5.3 400 / 44
* Flat head uses a standard 80°– 82° counter sink.
For continuous extreme low temperature applications, use stainless steel.

Typical Applications—Cladding and Brick Ties

Environment—Slight to moderate degree of pollution
Level of Corrosion—Medium

86 Call our toll free number 800-848-5611 or visit our web site for the most
current product and technical information at www.itwredhead.com
 PERFORMANCE TABLE
Dynabolt Ultimate Tension and Shear Values
Sleeve Anchors in Solid Concrete (lbs/kN)*
MINIMUM f’c = 2000 PSI (13.8 MPa) f’c = 3000 PSI (20.7 MPa) f’c = 4000 PSI (27.6 MPa)
ANCHOR INSTALLATION BOLT EMBEDMENT ANCHOR
DIAMETER TORQUE DIAMETER DEPTH TYPE TENSION SHEAR TENSION SHEAR TENSION SHEAR
in. (mm) ft. lbs. (Nm) in. (mm) in. (mm) (STEEL) lbs. (kN) lbs. (kN) lbs. (kN) lbs. (kN) lbs. (kN) lbs. (kN)
1/4 (6.4) 3.5 (4.7) 3/16 (4.8) 1-1/8 (28.6) 1,200 (5.3) 1,215 (5.4) 1,325 (5.9) 1,215 (5.4) 1,450 (6.4) 1,215 (5.4)
5/16 (7.9) 8 (10.8) 1/4 (6.4) 1-1/4 (31.8) 1,400 (6.2) 2,040 (9.1) 1,920 (8.5) 2,220 (9.9) 2,600 (11.6) 2,400 (10.7)
3/8 (9.5) 14 (19.0) 5/16 (7.9) 1-1/2 (38.1) Carbon or 1,620 (7.2) 2,560 (11.4) 2,240 (10.0) 2,800 (12.5) 3,100 (13.8) 3,040 (13.5)
1/2 (12.7) 20 (27.1) 3/8 (9.5) 1-7/8 (47.6) Stainless 2,220 (9.9) 3,250 (14.5) 3,140 (14.0) 4,000 (17.8) 4,400 (19.6) 4,500 (20.0)
5/8 (15.9) 48 (65.1) 1/2 (12.7) 2 (50.8) 3,080 (13.7) 6,440 (28.6) 4,400 (19.6) 7,240 (32.2) 6,120 (27.2) 8,080 (35.9)
3/4 (19.1) 90 (122.0) 5/8 (15.9) 2-1/4 (57.2) 4,200 (18.7) 10,200 (45.4) 6,060 (27.0) 11,600 (51.6) 8,900 (39.6) 13,100 (58.3)
* For continuous extreme low temperature applications, use stainless steel.
* To calculate the Allowable Load of the anchor, divide the Ultimate Load by 4.

PERFORMANCE TABLE
Dynabolt Ultimate Tension and Shear Values
Sleeve Anchors in Lightweight Concrete (lbs/kN)*
MINIMUM f’c = 4000 PSI (27.6 MPa) f’c = 6000 PSI (41.4 MPa)
ANCHOR INSTALLATION EMBEDMENT
DIAMETER TORQUE BOLT DIAMETER DEPTH ANCHOR TYPE TENSION SHEAR TENSION SHEAR
in. (mm) ft. lbs. (Nm) in. (mm) in. (mm) (STEEL) lbs. (kN) lbs. (kN) lbs. (kN) lbs. (kN)
1/4 (6.4) 3.5 (4.7) 3/16 (4.8) 1-1/8 (28.6) 870 (3.9) 730 (3.2) 1,066 (4.7) 894 (4.0)
5/16 (7.9) 8 (10.8) 1/4 (6.4) 1-1/4 (31.8) 1,260 (5.6) 1,680 (7.5) 1,440 (6.4) 2,220 (9.9)
3/8 (9.5) 14 (19.0) 5/16 (7.9) 1-1/2 (38.1) 1,620 (7.2) 2,300 (10.2) 2,240 (10.0) 2,800 (12.5)
Carbon or Stainless
1/2 (12.7) 25 (33.9) 3/8 (9.5) 1-7/8 (47.6) 2,600 (11.6) 2,400 (10.7) 3,160 (14.1) 2,400 (10.7)
5/8 (15.9) 48 (65.1) 1/2 (12.7) 2 (50.8) 3,240 (14.4) 5,600 (24.9) 4,300 (19.1) 7,840 (34.9)
3/4 (19.1) 90 (122.0) 5/8 (15.9) 2-1/4 (57.2) 3,640 (16.2) 8,640 (38.4) 5,800 (25.8) 12,480 (55.5)
* To calculate the Allowable Load of the anchor, divide the Ultimate Load by 4.

PERFORMANCE TABLE
Dynabolt Ultimate Tension and Shear Values
Sleeve Anchors in Concrete Masonry Units (lbs/kN)*
LIGHTWEIGHT MEDIUM WEIGHT
MINIMUM HOLLOW CORE GROUT FILLED HOLLOW CORE GROUT FILLED
ANCHOR INSTALLATION BOLT EMBEDMENT ANCHOR
DIAMETER TORQUE DIAMETER DEPTH TYPE TENSION SHEAR TENSION SHEAR TENSION SHEAR TENSION SHEAR
in. (mm) ft. lbs. (Nm) in. (mm) in. (mm) (STEEL) lbs. (kN) lbs. (kN) lbs. (kN) lbs. (kN) lbs. (kN) lbs. (kN) lbs. (kN) lbs. (kN)
Carbon 1,120 (5.0) 1,215 (5.4) 1,120 (5.0) 1,215 (5.4) 1,120 (5.0) 1,215 (5.4) 1,120 (5.0) 1,215 (5.4)
1/4 (6.4) 3.5 (4.7) 3/16 (4.8) 1-1/8 (28.6)
Stainless 640 (2.8) 1,620 (7.2) 640 (2.8) 1,620 (7.2) 640 (2.8) 1,620 (7.2) 640 (2.8) 1,620 (7.2)
Carbon 1,360 (6.0) 2,560 (11.4) 1,360 (6.0) 2,560 (11.4) 1,360 (6.0) 2,560 (11.4) 1,360 (6.0) 2,560 (11.4)
3/8 (9.5) 15 (20.3) 5/16 (7.9) 1-1/2 (38.1)
Stainless 1,160 (5.2) 2,560 (11.4) 1,160 (5.2) 2,560 (11.4) 1,160 (5.2) 2,560 (11.4) 1,160 (5.2) 2,560 (11.4)
Carbon N/A N/A 2,200 (9.9) 3,500 (15.6) N/A N/A 2,200 (9.9) 3,500 (15.6)
1/2 (12.7) 25 (33.9) 3/8 (9.5) 1-7/8 (47.6)
Stainless N/A N/A 2,100 (9.3) 3,500 (15.6) N/A N/A 2,100 (9.3) 3,500 (15.6)
Carbon N/A N/A 3,080 (13.7) 6,440 (28.6) N/A N/A 3,080 (13.7) 6,440 (28.6)
5/8 (15.9) 55 (74.6) 1/2 (12.7) 2 (50.8)
Stainless N/A N/A 3,080 (13.7) 6,440 (28.6) N/A N/A 2,820 (12.5) 6,440 (28.6)
3/4 (19.1) 90 (122.0) 5/8 (15.9) 2-1/2 (63.5) Carbon N/A N/A 4,200 (18.7) 10,200 (45.4) N/A N/A 4,200 (18.7) 10,200 (45.4)
* To calculate the Allowable Load of the anchor, divide the Ultimate Load by 4. The tabulated values are for anchors installed in a minimum of 12 diameters on center and a minimum edge distance of 6 diameters for 100 percent
anchor efficiency. Spacing and edge distance may be reduced to 6 diameter spacing and 3 diameter edge distance, provided the values are reduced 50 percent. Linear interpolation may be used for intermediate
spacings and edge distances.
Note: N/A is defined as Not Advisable.

Combined Tension and Shear Loading—for Dynabolt Anchors

Allowable loads for anchors subjected to combined shear and tension forces are determined by the following equation:
(Ps/Pt) + (Vs/Vt) ≤ 1
Ps = Applied tension load Vs = Applied shear load Pt = Allowable tension load Vt = Allowable shear load

Call our toll free number 800-848-5611 or visit our web site for the most
current product and technical information at www.itwredhead.com 87