Product datasheet ATS22C21Q

Characteristics

Main
Range of product Altistart 22
Product or component type Soft starter
Product destination Asynchronous motors
Product specific application Pumps and fans
Component name ATS22
Phase 3 phases
[Us] rated supply voltage 230...440 V - 15...10 %
Motor power kW 110 kW 400 V
110 kW 440 V
55 kW 230 V
Factory setting current 195 A

It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof.
Power dissipation in W 117 W for standard applications
Utilisation category AC-53A
Type of start Start with torque control (current limited to 3.5 In)
IcL starter rating 210 A connection in the motor supply line for
standard applications
IP degree of protection IP00

The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein.
This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications.
Complementary

Neither Schneider Electric Industries SAS nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein.
Assembly style With heat sink
Function available Internal bypass
Supply voltage limits 195...484 V
Supply frequency 50...60 Hz - 10...10 %
Network frequency 45...66 Hz
Device connection In the motor supply line
To the motor delta terminals
[Uc] control circuit voltage 230 V -15...10 % 50/60 Hz
Control circuit consumption 20 W
Discrete output number 2
Discrete output type Relay outputs R1 230 V running, alarm, trip, stopped, not stopped, starting, ready C/O
Relay outputs R2 230 V running, alarm, trip, stopped, not stopped, starting, ready C/O
Minimum switching current 100 mA 12 V DC relay outputs
Maximum switching current 5 A 250 V AC resistive 1 relay outputs
5 A 30 V DC resistive 1 relay outputs
2 A 250 V AC inductive 0.4 20 ms relay outputs
2 A 30 V DC inductive 7 ms relay outputs
Discrete input number 3
Discrete input type Logic LI1, LI2, LI3 5 mA 4.3 kOhm
Discrete input voltage 24 V <= 30 V
Discrete input logic Positive logic LI1, LI2, LI3 < 5 V and <= 2 mA > 11 V >= 5 mA
Output current 0.4...1 Icl adjustable
PTC probe input 750 Ohm
Communication port protocol Modbus
Connector type 1 RJ45
Communication data link Serial
Physical interface RS485 multidrop
Transmission rate 4800, 9600 or 19200 bps
Installed device 31
Protection type Thermal protection motor

1/8
 Phase failure line
Thermal protection starter
Marking CE
Type of cooling Forced convection
Operating position Vertical +/- 10 degree
Height 16.73 in (425 mm)
Width 8.11 in (206 mm)
Depth 11.77 in (299 mm)
Product weight 72.75 lb(US) (33 kg)
Power range 55...100 kW at 200...240 V 3 phases
110...220 kW at 380...440 V 3 phases
Motor starter type Soft starter

Environment
electromagnetic compatibility Conducted and radiated emissions level A IEC 60947-4-2
Damped oscillating waves level 3 IEC 61000-4-12
Electrostatic discharge level 3 IEC 61000-4-2
Immunity to electrical transients level 4 IEC 61000-4-4
Immunity to radiated radio-electrical interference level 3 IEC 61000-4-3
Voltage/current impulse level 3 IEC 61000-4-5
standards EN/IEC 60947-4-2
product certifications CCC
CSA
C-Tick
GOST
UL
vibration resistance 1 gn 13...200 Hz EN/IEC 60068-2-6
1.5 mm 2...13 Hz EN/IEC 60068-2-6
shock resistance 15 gn 11 ms EN/IEC 60068-2-27
noise level 56 dB
pollution degree Level 2 IEC 60664-1
relative humidity 0...95 % without condensation or dripping water EN/IEC 60068-2-3
ambient air temperature for operation 14...104 °F (-10...40 °C) without derating
> 104...< 140 °F (> 40...< 60 °C) with current derating 2.2 % per °C
ambient air temperature for storage -13...158 °F (-25...70 °C)
operating altitude <= 3280.84 ft (1000 m) without derating
> 3280.84...< 6561.68 ft (> 1000...< 2000 m) with current derating of 2.2 % per
additional 100 m

Offer Sustainability
Green Premium product Green Premium product
Compliant - since 0939 - Schneider Electric declaration Compliant - since 0939 - Schneider Electric declaration of conformity
of conformity
Reference not containing SVHC above the threshold Reference not containing SVHC above the threshold
Available Available
Available Available
WARNING: This product can expose you to chemicals WARNING: This product can expose you to chemicals including:
including:
Lead and lead compounds, which is known to the State Lead and lead compounds, which is known to the State of California to cause cancer
of California to cause cancer and birth defects or other and birth defects or other reproductive harm.
reproductive harm.
Bisphenol A (BPA), which is known to the State of Bisphenol A (BPA), which is known to the State of California to cause birth defects or
California to cause birth defects or other reproductive other reproductive harm.
harm.
For more information go to www.p65warnings.ca.gov For more information go to www.p65warnings.ca.gov

Contractual warranty
Warranty period 18 months

Frame Size D

2/8
Dimensions

Precautions
Standards

The Altistart 22 soft starter is compliant with pollution Degree 2 as defined in NEMA ICS1-1 or IEC 60664-1.
For environment pollution degree 3, install the Altistart 22 soft starter inside a cabinet type 12 or IP54.

DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
ATS22 soft starters are open devices and must be mounted in a suitable enclosure.
Failure to follow these instructions will result in death or serious injury.
Air Circulation

Leave sufficient free space to help the air required for cooling purposes to circulate from the bottom to the top of the unit.

Overheating

To avoid the soft starter to overheat, respect the following recommendations:

Š Mount the Altistart 22 Soft Starter within ± 10° of vertical.
Š Do not locate the Altistart 22 Soft Starter near heat radiating elements.
Š Electrical current through the Altistart 22 Soft Starter will result in heat losses that must be dissipated into the ambient air
immediately surrounding the soft starter. To help prevent a thermal fault, provide sufficient enclosure cooling and/or ventilation to
limit the ambient temperature around the soft starter.
Š If several soft starters are installed in a control panel, arrange them in a row. Do not stack soft starters. Heat generated from the

3/8
 bottom soft starter can adversely affect the ambient temperature around the top soft starter.

Wall mounted or Floor-standing Enclosure with IP 23 Degree of protection

Introduction

To help proper air circulation in the soft starter, grilles and forced ventilation can be installed.
Ventilation Grilles

Forced Ventilation Unit

Power Terminal
Bar Style

Power supply and output to motor Bar b 30 mm (1.18 in)

a 5 mm (0.2 in)

Bolt M12 (0.47 in)

Cable and protective cover Size 2 X 150 mm²

Gauge 2 X 250 MCM

Protective cover LA9F703

Tightening torque 57 N.m

498.75 lb.in

Power connections, minimum required wiring section

IEC cable UL cable

mm² (Cu 70°C/158°F) (1) AWG (Cu 75°C/167°F) (1)

95 300 MCM

230 Vac control, logic Inputs (LI) 24 Vdc, 3-wire control

With Line Contactor, Freewheel or Controlled Stop

4/8
230 Vac control, logic Inputs (LI) 24 Vdc, 2-wire control,freewheel stop

Connection in the motor delta winding in series with each winding

Wiring

ATS22 soft starters connected to motors with the delta connections can be inserted in series in the motor windings.
The following wiring requieres particular attention. It is documented in the Altistart 22 Soft start - soft stop unit user manual. Please
contact Schneider Electric commercial organisation for further informations.

5/8
Example

A 400 V - 110 kW motor with a line current of 195 A (nominal current for the delta connection). The current in each winding is equal to
195/1.5 or 130 A. The rating is determined by selecting the soft starter with a permanent nominal current (ICL) just above this current.

Motor Thermal Protection - Cold Curves

Curves

A Class 10
B Class 20
C Class 30

6/8
Trip time for a Standard Application (Class 10)

3.5 ln

32 s

Trip time for a Severe Application (Class 20)

3.5 ln

63 s

Trip time for a Severe Application (Class 30)

3.5 ln

95 s

Motor Thermal Protection - Warm Curves

Curves

A Class 10
B Class 20
C Class 30
Trip time for a Standard Application (Class 10)

3.5 ln

16 s

Trip time for a Severe Application (Class 20)

7/8
3.5 ln

32 s

Trip time for a Severe Application (Class 30)

3.5 ln

48 s

8/8
Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Schneider Electric:
ATS22C21Q