Scribd Logo
Upload

Welcome to Scribd!

  • 29 views

    Miniature Crystal Oven Specification: Maj43Vv

    Uploaded by

    snewton6752
    This document specifies the operating characteristics of a miniature crystal oven component heater (MAJ43VV). It provides temperature set points between 35-95°C that can be adjusted via an external resistor. The oven heats crystals like the HC series and operates on input voltages between 5-28VDC with less than 6 watts of power. It has a tolerance of ±5°C initial tolerance and maintains stability of ±3°C over temperature ranges and voltage changes.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Miniature Crystal Oven Specification: Maj43Vv

    Uploaded by

    snewton6752
    29 views3 pages
    This document specifies the operating characteristics of a miniature crystal oven component heater (MAJ43VV). It provides temperature set points between 35-95°C that can be adjusted via an external resistor. The oven heats crystals like the HC series and operates on input voltages between 5-28VDC with less than 6 watts of power. It has a tolerance of ±5°C initial tolerance and maintains stability of ±3°C over temperature ranges and voltage changes.

    Original Description:

    Adjustable Minioven Specification

    Original Title

    MAJ43VV

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document specifies the operating characteristics of a miniature crystal oven component heater (MAJ43VV). It provides temperature set points between 35-95°C that can be adjusted via an external resistor. The oven heats crystals like the HC series and operates on input voltages between 5-28VDC with less than 6 watts of power. It has a tolerance of ±5°C initial tolerance and maintains stability of ±3°C over temperature ranges and voltage changes.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    29 views3 pages

    Miniature Crystal Oven Specification: Maj43Vv

    Uploaded by

    snewton6752
    This document specifies the operating characteristics of a miniature crystal oven component heater (MAJ43VV). It provides temperature set points between 35-95°C that can be adjusted via an external resistor. The oven heats crystals like the HC series and operates on input voltages between 5-28VDC with less than 6 watts of power. It has a tolerance of ±5°C initial tolerance and maintains stability of ±3°C over temperature ranges and voltage changes.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    1801 Broadway Street Charlottesville, Virginia 22902 USA

    www.isotemp.com Phone: (434) 295-3101 Fax: (434) 220-3166

    MAJ43VV

    MINIATURE CRYSTAL OVEN SPECIFICATION


    This specification defines the operating characteristics of a component heater. Long term reliability and stability are assured through use of premium components.
    REV. DESCRIPTION OF REVISION REV./DWN. BY TST APPROV. BY TST DATE 03-01-2006

    This MAJ43VV specification covers input voltages from +5 VDC to +28 VDC. The VV** in the part number specifies the nominal operating voltage. If the voltage is less than +10 VDC, use a leading zero (i.e. for +5 VDC use VV = 05). The TT in this specification describes set point temperature in C (i.e. for +75C use TT = 75). ** See the TABLE at the end of this specification for available voltages. 1. TEMPERATURE 1.1. Set point

    +TT C (Customer adjustable) (+35C to +95C) (Set by an external resistor between the "TEMPERATURE ADJUST" Pin and the "0 VDC" Pin. See the TABLE at the end of this specification for resistor value to set the temperature.) (Use metal film resistors to prevent aging of the set point temperature.) < 5C @ +25C

    1.2. Initial tolerance 2. STABILITY 2.1. Ambient 2.2. Voltage 2.3. Warm-up 3. INPUT POWER 3.1. Voltage

    3C from -30C to (TT-10)C 0.5C/10% change 1C in 2 minutes @ +25C (Referenced to temperature at 15 minutes) VV VDC (Customer specified) (+5 VDC to +28 VDC) 10%

    3.2. Voltage tolerance 3.3. Power a. At turn on < 6 Watts @ +25C b. Slope * -0.024 Watts/C typical To calculate the typical steady state power (Pss), use the following formula. Pss = (TT - ambient temperature of unit)C x 0.024 (Watts) 4. MECHANICAL 4.1. Heated cavity holds the following crystals 4.2. Applicable series 4.3. Model number 4.4. Outline drawing * In still air.

    HC-18/U, HC-25/U, HC-42/U, HC-43/U, HC-49/U, AND HC-50/U MAJ43 series MAJ43VV (Customer specified) 125-365

    See ISOTEMP application note 146-003 for design considerations.

    ISOTEMP RESEARCH INC. CHARLOTTESVILLE, VA. USA

    Code ID.

    Model Number

    Page of Total

    Drawing Number

    Rev.

    31785

    MAJ43VV

    114-1248

    1801 Broadway Street Charlottesville, Virginia 22902 USA

    www.isotemp.com Phone: (434) 295-3101 Fax: (434) 220-3166

    MAJ43VV

    Voltage -> 35 40 45 50 55 60 65 70 75 80 85 90 95 ^Temp(C)

    5 298.12 232.49 186.93 149.90 115.64 92.01 70.06 56.36 44.64 31.69 26.20 17.78 9.87

    8 349.86 254.77 204.07 163.76 127.71 104.92 80.44 62.84 52.25 37.86 28.89 22.35 13.55

    10 12 15 18 20 349.86 399.67 399.67 441.80 503.99 280.53 298.12 317.56 349.86 399.67 210.75 232.49 254.77 280.53 298.12 175.27 186.93 204.07 232.49 232.49 139.97 149.90 149.90 175.27 186.93 104.92 115.64 127.71 139.97 149.90 82.74 92.01 97.85 115.64 115.64 70.06 72.56 80.44 92.01 92.01 52.25 60.60 60.60 70.06 72.56 42.88 44.64 48.38 56.36 60.60 31.69 37.86 37.86 44.64 44.64 22.35 26.20 28.89 31.69 37.86 15.66 17.78 21.18 26.20 26.20 Required external resistor (k ohms)

    24 503.99 399.67 317.56 254.77 204.07 158.69 127.71 104.92 80.44 62.84 52.25 37.86 31.69

    28 622.30 503.99 349.86 298.12 232.49 186.93 149.90 115.64 92.01 80.44 60.60 48.38 37.86

    To determine resistor between two temperatures use the following formula: R = EXP ( ( ln(R2/R1) x ( Td T1) / (T2 T1) + ln(R1)) Where: R = resistor value required for temperature Td. Td = Temperature desired T2 = Temperature just above Td R2 = Resistor value corresponding to T2 T1 = Temperature just below Td R1 = Resistor value corresponding to T1

    ISOTEMP RESEARCH INC. CHARLOTTESVILLE, VA. USA

    Code ID.

    Model Number

    Page of Total

    Drawing Number

    Rev.

    31785

    MAJ43VV

    114-1248

    .750 DIA.

    PIN CONNECTIONS
    PIN FUNCTION
    +VDC TEMPERATURE ADJUST
    or

    MODEL XXXX
    CRYSTAL CAVITY

    1
    (See Note 3)

    NOT CONNECTED 0 VDC

    .625

    NOTE: 1. CRYSTAL CAVITY IS CONNECTED TO 0 VDC 2. MARKING: LABEL MODEL = M43VVTT or MAJ43VV VV = VOLTAGE TT = SET POINT TEMPERATURE XXXX = DATE CODE 3. "TEMPERATURE ADJUST" FOR M43AJVV MODELS "NOT CONNECTED" FOR M43VVTT MODELS

    .062 .500

    .020 DIA. PIN (3 PLACES)

    .406 45

    .600 DIA. (PIN CIRCLE)

    .156

    FORM NO. 120-081D

    REV: B SHT: 1 OF 1

    DWG: 125-365

    OSCILLATORS

    CHARLOTTESVILLE, VIRGINIA CODE I.D. NO. SCALE: 2:1 DWN. BY: WEW
    08-15-00

    NAME: OUTLINE DRAWING


    (M43 & MAJ43 SERIES)
    B REDRAWN, NEW FORM, REVISED NOTES.

    DATE: 05-07-91 APPR'D. BY: TST TOLERANCES

    31785
    LRB DAG

    LET

    REVISION

    BY

    APP

    DATE

    UNLESS OTHERWISE SPECIFIED: ANGLES: 1 DEGREE FRACTIONS: 1/32 INCH DECIMALS: .XX .015, .XXX .010 COVER MATERIAL: GLASS-FIBRE FILLED DIALLYL PHTHALATE BASE MATERIAL: VALOX 420 SEO BLACK PIN MATERIAL: KOVAR WITH 60/40 SOLDER ELECTROPLATE OVER NICKEL FINISH: N/A MARK: LABEL

    You might also like