Epson WF C5790 WF C5790A WF C5710 ET 8700 WF C5210 WF C5290 WF C5290A Service Manuals 351 400

EPSON WF-C5790/WF-C5790a/WF-C5710/ET-8700/WF-C5210/WF-C5290/WF-C5290a Revision A
B6 B7
Housing Upper Speaker Assy
C6
Top
Main Board Assy
Housing
Upper
CN3 Cable Speaker Assy
Top
Speaker Holder
Slit
No. Screw Type No. Screw Type

S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C
1. Remove the six screws (S4: ), then remove the Housing Upper. 1. Disconnect the cable from the connector (CN3) on the Main Board Assy.
2. Release the cable from seven slits on the Frame Base.
3. Remove the two screws (S4: ), then remove the Speaker Holder.
4. Remove the Speaker Assy.
Disassembly/assembly Disassembly/Reassembly Procedures 351

Confidential
Cable Guide
Cable Guide
C7
Guides PS Cable
Cable Guide
Solenoid cable Cable Guide
Guide Hook
Rear ASF sensor cable/

ASF motor cable Photo interrupter cable
No. Screw Type

S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C
1. Release the all cable from the Cable Guide.  Route the PS cable through the two guides and hook on the Cable Guide.
2. Remove the two screws (S4: ), and remove the Cable Guide.  Route the solenoid cable through the five hooks ( ) on the Cable Guide.
 Route the rear ASF sensor cable and photo interrupter cable through the three hooks ( ) on
the Cable Guide.
 Route the ASF motor cable through the guide on the Cable Guide.

Confidential
ADF/SCN Unit
ADF/SCN Unit
C8
Open Close
ADF/SCN Unit 45 °
Connector Lock
CN801 Double-sided tape
CN612
CN606
CN601
Grounding cable No. Screw Type

Acetate tape S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C
C H E C K When disconnecting the CISM FFC (CN601) from this connector, make sure to 3. Open the ADF/SCN Unit.
P O IN T
unlock the connector lock beforehand. 4. Remove the two screws (S4: ), then remove the ADF/SCN Unit in the direction of the
arrow.
1. Disconnect the cables and FFCs from following connectors on the Main Board.
 Before screwing the ADF/SCN Unit, make sure the hinges are properly attached in place.
 If the ADF/SCN Unit is opened when the hinges are NOT secured, the unit may be damaged.
• CN601 • CN606 • CN612 • CN801
2. Peel off the acetate tape, then remove the grounding cable.

Confidential
Hinge Assy Hinge Lower Cover

C9 C10
Hinge Lower Hinge Lower

Hinge Assy (Left) Hinge Assy (Right) Cover (Left) Cover (Right)
Hinge Lower Cover

C H E C K When removing the Main Board Assy on the way to the target part, remove the Hinge C H E C K When removing the Main Board Assy on the way to the target part, remove the Hinge
P O IN T P O IN T
Assy (Left) only. Assy (Left) only.
1. Remove the each screw (S4: ), and remove the two Hinge Assy. 1. Remove the each three screws (S4: ), and remove the two Hinge Lower Cover.

Confidential
Rear ASF Assy
Rear ASF Assy

C11
Cable Guide
Rear ASF Assy

Solenoid cable
Photo interrupter cable
CN56
CN51
Relay Board
No. Screw Type
1. Disconnect the cables from the connectors (CN51, CN56) on the Relay Board. 3. Remove the four screws (S4: ), and remove the Rear ASF Assy.
2. Release the solenoid cable and photo interrupter cable from the Cable Guide.
 Route the solenoid cable through the five hooks ( ) on the Cable Guide.
 Route the photo interrupter cable through the three hooks ( ) on the Cable Guide.

Confidential
PS Ground Plate Rear ASF Upper Guide Assy

C12 C13
FFC
Top
Hooks
PS Ground Plate
Rear
Rear ASF Upper Guide Assy AC Inlet

S5 C.B.S-TITE-SCREW-3x6-F.ZN-3C S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C
1. Remove the two screws (S4: , S5: ), then remove the PS Ground Plate. 1. Remove the screw (S4: ) that secures the AC Inlet.
2. Release the FFC from three hooks on the Rear ASF Upper Guide Assy.
3. Remove the four screws (S4: ), then remove the Rear ASF Upper Guide Assy.

Confidential
Power Supply Assy

C14
PS Cable
Ferrite Core Ferrite Core
Slit Power Supply Assy Slit
AC Cable Hook Slit Hook Guide
Rea ASF Upper Guide Assy
No. Screw Type

1. Remove the screw (S4: ), then remove the Power Supply Assy.
 Route the AC Cable through the two slits, two hooks and guide on the Rea ASF Upper Guide
Assy.
 Route the PS Cable through the slit on the Rea ASF Upper Guide Assy.

Confidential
6.2.4.12 Electrical Components (3) (WF-C5700 Series/ET-8700)
OUTLINE
Time
Part or Component Guide Disassembly/ Adjustment/
Total
Reassembly Inspection
Panel Assy A --- --- ---
Numpad Board Assy B --- --- ---
Panel Board C --- --- ---
Relay Cable (Panel to

Main) D --- --- ---
Relay Cable (Panel to

E --- --- ---
Numpad)

Confidential
DISASSEMBLY FLOWCHART
Start
Start
A1 B1 C1 Rear Cover (Back)

D1 E1 (→P. 360)
A2 B2 C2 ASF Front Cover

D2 E2 (→P. 360)
A3 B3 C3 Ink Eject Cover

D3 E3 (→P. 361)
A4 B4 C4 Housing Right
D4 E4 (→P. 361)
A5 B5 C5 Housing Left
D5 E5 (→P. 362)
A6 B6 C6 Housing Upper
D6 E6 (→P. 362)
A7 B7 C7 Cable Guide
D7 E7 (→P. 363)
A8 B8 C8 Panel Assy
D8 E8 (→P. 364)
B9 C9 Panel Housing
D9 E9 (→P. 365)
B10 Numpad Board Assy C10 Panel Board D10 Relay Cable (Panel to Main) E10 Relay Cable (Panel to
(→P. 365) (→P. 366) (→P. 366) Numpad) (→P. 367)

Confidential
A1 B1 C1 A2 B2 C2
Rear Cover (Back) ASF Front Cover
D1 E1 D2 E2
Rear Cover (Back)
ASF Front Cover
Dowel and Dowel and

positioning hole positioning hole
Housing Right Housing Left

Rear Cover (Back)

1. Remove the four screws (S4: ), then remove the Rear Cover (Back). 1. Remove the four screws (S4: ) that secure the ASF Front Cover.
Attach the two dowels of the Rear Cover (Back) to the positioning holes on the 2. Remove the ASF Front Cover upward while slightly bending the Rear Cover (Back) toward
Housing Left and Housing Right. the back.

Confidential
A3 B3 C3 A4 B4 C4
Ink Eject Cover Housing Right
D3 E3 D4 E4
Rear
Hook
Housing Right
Hooks
Ink Eject Cover

Tabs
No. Screw Type

1. Disengage the hook, and remove the Ink Eject Cover. 1. Open the ADF/SCN Unit.
2. Remove the four screws (S4: ) that secure the Housing Right.
3. Lift the Housing Right to release the two hooks on the front side of the Housing Right, then
remove the Housing Right.
Insert the four tabs of the Housing Right to the positioning holes on the Ink Supply
Unit.

Confidential
A5 B5 C5 A6 B6 C6
Housing Left Housing Upper
D5 E5 D6 E6
Rear
Housing
Hooks Upper
Housing Left
Hooks Top

S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C Tab S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C
1. Open the ADF/SCN Unit. 1. Remove the six screws (S4: ), then remove the Housing Upper.
2. Remove the three screws (S4: ) that secure the Housing Left.
3. Lift the Housing Left to release the two hooks on the front side of the Housing Left.
4. Disengage two hooks on the rear side of the Housing Left, and remove the Housing Left.
Insert the eight tabs on the Housing Left to the positioning hokes of the Housing
Upper and the Ink Supply Unit.

Confidential
Cable Guide
A7 B7 C7
Cable Guide
D7 E7
Guides PS Cable
Cable Guide
Guide Hook

ASF motor cable Photo interrupter cable
No. Screw Type

1. Release the all cable from the Cable Guide.  Route the PS cable through the two guides and hook on the Cable Guide.
2. Remove the two screws (S4: ), and remove the Cable Guide.  Route the solenoid cable through the five hooks ( ) on the Cable Guide.
 Route the rear ASF sensor cable and photo interrupter cable through the three hooks ( ) on
the Cable Guide.

Confidential
Panel Assy
A8 B8 C8
Panel Assy
D8 E8
Close
Right Panel Holder

FFC Tab
Open
Ferrite core
Bearing Shaft Panel Assy
Main Board
Assy
Double-sided tape
CN42
Connector lock
No. Screw Type

C H E C K When disconnecting the FFC, make sure to unlock the connector lock beforehand. 4. Remove the two screws (S4: ), then remove the Right Panel Holder.
P O IN T
5. Release the shaft of the Panel Assy from bearing, then remove the Panel Assy.
1. Disconnect the FFC from the connector (CN42) on the Main Board Assy.
2. Peel off the FFC from the Frame Base.
3. Release the FFC from two tabs on the Frame Base.
Set the ferrite core of the FFC in the point shown above.

Confidential
B9 C9 B10
Panel Housing Numpad Board Assy
D9 E9
Panel FFCCover
Cover
Numpad Board Assy Panel Board
Relay Cable Double-sided tape CN311
OK NG
Panel Housing Hole Panel FFC Cover
Relay Cable Cover

Hooks Relay Cable Hook
No. Screw Type
No. Screw Type S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C
1. Remove the six screws (S4: ) that secure the Panel Housing. 1. Peel off the Relay Cable Cover, and disconnect the FFC from the connector (CN311) on the
2. Disengage three hooks on the Panel Housing, and remove the Panel Housing. Panel Board.
3. Remove the Panel FFC Cover. 2. Remove the screw (S4: ), and remove the Relay Cable Cover.
3. Remove the four screws (S4: ), and remove the Numpad Board Assy.
Install the Panel FFC Cover as shown above.
4. Pull the Relay Cable out from the hole of the Panel Housing.

Confidential
C10
Panel Board Relay Cable (Panel to Main)
D10
Relay Cable
CN101
Connector lock
CN311 Panel Board
Panel Board
CN302
Close Open
No. Screw Type

1. Disconnect the FFC from the connectors (CN302, CN311) on the Panel Board. C H E C K When disconnecting the FFC, make sure to unlock the connector lock beforehand.
P O IN T
2. Remove the eight screws (S4: ), then remove the Panel Board.
1. Disconnect the Relay Cable from the connector (CN101) on the Panel Board.

Confidential
Relay Cable (Panel to Numpad)

E10
Numpad Board Assy Panel Board
Relay Cable Double-sided tape CN311
CN102
Relay Cable Cover
1. Peel off the Relay Cable from the Relay Cable Cover.
2. Disconnect the Relay Cable from the connectors (CN102, CN311) on the Panel Board and
Numpad Board Assy.

Confidential
6.2.4.13 Electrical Components (3) (WF-C5200 Series)
OUTLINE
Time
Total
Panel Assy A --- --- ---
Panel Board B --- --- ---
Relay Cable (Panel to Main) C --- --- ---

Confidential
Start
Start
A1 B1 Rear Back Cover

C1 (→P. 370)
A2 B2 Rear Upper Cover Assy

C2 (→P. 371)
A3 B3 Housing ASF
C3 (→P. 371)
A4 B4 Printer Cover
C4 (→P. 372)
A5 B5 Ink Eject Cover

C5 (→P. 372)
A6 B6 Housing Right
C6 (→P. 373)
A7 B7 Housing Left
C7 (→P. 373)
A8 B8 Housing Top
C8 (→P. 374)
A9 B9 Cable Guide B11 Panel Housing

C9 (→P. 374) C11 (→P. 376)
A10 B10 Panel Assy B12 Panel Board C12 Relay Cable (Panel to Main)
C10 (→P. 375) (→P. 377) (→P. 377)

Confidential
Rear Back Cover

A1 B1
Rear Back Cover
C1
Top Rear Upper

Cover Assy
Rear Rear Back

Rear Back Cover
Cover
Dowel Dowel
No. Screw Type

1. Remove the two screws (S4: ) that secure the Rear Upper Cover Assy. 3. Remove the Rear Back Cover downward.
2. Remove the four screws (S4: ) that secure the Rear Back Cover. Attach the two dowels of the Rear Back Cover to the positioning holes on the Housing
Left and the Housing Right.

Confidential
A2 B2 A3 B3
Rear Upper Cover Assy Housing ASF
C2 C3
Housing ASF
Rear Upper Cover Assy
Housing ASF
Tabs
Printer
Cover
No. Screw Type

1. Remove the Rear Upper Cover Assy in the direction of the arrow. 1. Open the Printer Cover.
Insert the four tabs of the Rear Upper Cover Assy to the positioning holes of the 2. Remove the six screws (S4: ), then remove the Housing ASF.
Housing ASF.

Confidential
A4 B4 A5 B5
Printer Cover Ink Eject Cover
C4 C5
Printer Cover Hook
Ink Eject Cover
1. Remove the Printer Cover upward. 1. Disengage the hook, and remove the Ink Eject Cover.

Confidential
A6 B6 A7 B7
C6 C7
Rear Rear
Hooks
Housing Left
Housing Right
Hooks
Hooks

Tab S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C Tab
1. Remove the five screws (S4: ) that secure the Housing Right. 1. Remove the five screws (S4: ) that secure the Housing Left.
2. Lift the Housing Right upward to release the two hooks on the front side of the Housing 2. Lift the Housing Left upward to release the two hooks each on the front side and rear side of
Right, and then remove the Housing Right. the Housing Left, and then remove the Housing Left.
Insert the four tabs of the Housing Right to the positioning holes of the Ink Supply Insert the four tabs of the Housing Left to the positioning holes of the Ink Supply Unit.
Unit.

Confidential
A8 B8 A9 B9
Housing Top Cable Guide
C8 C9
Cable Guide
Housing Top

1. Remove six screws (S4: ), then remove the Housing Top. 1. Release the all cable from the Cable Guide.
2. Remove the two screws (S4: ), and remove the Cable Guide.

Confidential
Cable Guide
A10 B10
Panel Assy
C10
Close
Guides PS Cable
FFC Tab
Open
Ferrite Core
Main Board
Assy
Guide Hook
Double-sided tape

ASF motor cable Photo interrupter cable CN42
Connector lock
The disassembling procedure for the Panel
C H E C K
P O IN T
Assy of the WF-C5700 Series/ET-8700 is
explained here.
The appearance of the Panel Assy differs
between WF-C5200 Series and WF-C5700
Series/ET-8700, however, the disassembly and
assembly procedure itself is the same.
 Route the PS cable through the two guides and hook on the Cable Guide. 1. Disconnect the FFC from the connector (CN42) on the Main Board Assy.
 Route the solenoid cable through the five hooks ( ) on the Cable Guide.
C H E C K When disconnecting the FFC, make sure to unlock the connector lock beforehand.
 Route the rear ASF sensor cable and photo interrupter cable through the three hooks ( ) on P O IN T
the Cable Guide.

2. Peel off the FFC from the Frame Base.
3. Release the FFC from two tabs on the Frame Base.
Set the ferrite core of the FFC in the point shown above.

Confidential
Panel Assy
B11
Panel Housing
C11
Panel FFC Cover
Right Panel Holder
OK NG
Bearing Shaft Panel Assy
Hook Panel FFC Cover

Hook Panel Housing Hole
Relay Cable Hooks

Hooks
4. Remove the two screws (S4: ), then remove the Right Panel Holder. 1. Remove the five screws (S4: ) that secure the Panel Housing.
5. Release the shaft of the Panel Assy from the bearing, then remove the Panel Assy. 2. Disengage five hooks on the Panel Housing, then remove the Panel Housing.
3. Remove the Panel FFC Cover.
Attach the panel FFC Cover as shown above.
4. Pull the Relay Cable out from the hole of the Panel Housing.

Confidential
B12
Panel Board Relay Cable (Panel to Main)
C12
Relay Cable
CN1 Connector lock
Panel Board
FFC
Panel Board Close Open

CN2
No. Screw Type

1. Disconnect the FFC from the connector (CN2) on the Panel Board. C H E C K When disconnecting the Relay Cable, make sure to unlock the connector lock
P O IN T
2. Remove the four screws (S4: ), then remove the Panel Board. beforehand.
1. Disconnect the Relay Cable from the connector (CN1) on the Panel Board.

Confidential
6.2.4.14 Inksystem
OUTLINE
Time
Total
Ink Eject Cover A --- --- ---
Inksystem Unit B --- --- ---
Maintenance Box Detect

Sensor Assy C --- --- ---
Porous Pad Cap Lower D --- --- ---

Confidential
Start
Start
A1 Ink Eject Cover B1 D1 Rear Cover (Back) C H E C K  As for the procedure indicated by , refer to 6.2.4.4
(→P. 380) C1 (→P. 380) P O IN T Housing (WF-C5200 Series) (2) (p. 254) in the case of
the WF-C5200 Series, and remove the parts from the
Rear Back Cover to the Housing Top.
B2 D2 ASF Front Cover  The procedure indicated by is applicable only in the
C2 (→P. 381)
WF-C5700 Series/ET-8700.
B3 D3 Ink Eject Cover

C3 (→P. 381)
B4 D4 Housing Right
C4 (→P. 382)
B5 D5 Housing Left
C5 (→P. 382)
B6 D6 Housing Upper
C6 (→P. 383)
B7 D7 ADF/SCN Unit
C7 (→P. 383)
B8 D8 Slide the Wasted Ink Duct

C8 Holder (→P. 384)
B9 Inksystem Unit C9 Maintenance Box Detect

D9 (→P. 385) Sensor Assy (→P. 387)
D10 Porous Pad Cap Lower

(→P. 388)

Confidential
A1 B1
Ink Eject Cover Rear Cover (Back)
C1 D1
Rear Cover (Back)
Hook
Dowel and Dowel and

Ink Eject Cover
No. Screw Type

1. Disengage the hook, and remove the Ink Eject Cover. 1. Remove the four screws (S4: ), then remove the Rear Cover (Back).
Attach the two dowels of the Rear Cover (Back) to the positioning holes on the
Housing Left and Housing Right.

Confidential
B2 B3
ASF Front Cover Ink Eject Cover
C2 D2 C3 D3
Hook
ASF Front Cover
Rear Cover (Back)
Ink Eject Cover
No. Screw Type

1. Remove the four screws (S4: ) that secure the ASF Front Cover. 1. Disengage the hook, and remove the Ink Eject Cover.
2. Remove the ASF Front Cover upward while slightly bending the Rear Cover (Back) toward
the back.

Confidential
B4 B5
C4 D4 C5 D5
Rear Rear
Hooks
Housing Left
Housing Right
Hooks
Hooks
Tabs

S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C Tab
1. Open the ADF/SCN Unit. 1. Open the ADF/SCN Unit.

2. Remove the four screws (S4: ) that secure the Housing Right. 2. Remove the three screws (S4: ) that secure the Housing Left.
3. Lift the Housing Right to release the two hooks on the front side of the Housing Right, then 3. Lift the Housing Left to release the two hooks on the front side of the Housing Left.
remove the Housing Right. 4. Disengage two hooks on the rear side of the Housing Left, and remove the Housing Left.
Insert the four tabs of the Housing Right to the positioning holes on the Ink Supply Insert the eight tabs on the Housing Left to the positioning hokes of the Housing
Unit. Upper and the Ink Supply Unit.

Confidential
B6 B7
Housing Upper ADF/SCN Unit
C6 D6 C7 D7
Open Close
Housing
Upper
Connector Lock
Top CN612
CN606
CN601
No. Screw Type

Grounding cable
S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C Acetate tape
1. Remove the six screws (S4: ), then remove the Housing Upper. C H E C K When disconnecting the CISM FFC (CN601) from this connector, make sure to
P O IN T
unlock the connector lock beforehand.
• CN601 • CN606 • CN612 • CN801


Confidential
ADF/SCN Unit
B8
Slide the Wasted Ink Duct Holder
C8 D8
Hook
ADF/SCN Unit 45 °
Wasted Ink Duct Holder
No. Screw Type

No. Screw Type
3. Open the ADF/SCN Unit. 1. Remove the screws (S4: ) that secure the Wasted Ink Duct Holder.
4. Remove the two screws (S4: ), then remove the ADF/SCN Unit in the direction of the 2. Disengage the hook, and slide the Wasted Ink Duct Holder to rear.
arrow.

Confidential
Inksystem Unit
B9
Inksystem Unit
D9 Top
Grounding cable
Wasted Ink Tube
Tube clamp
Grounding cable Upper Cap Frame Relay connector
Wasted Ink Duct Holder

Cable
No. Screw Type

S5 C.B.S-TITE-SCREW-3x6-F.ZN-3C
C H E C K Before removing the Inksystem Unit, release the carriage lock, and then move the CR 2. Remove the three screws (S5: ), then remove the Upper Cap Frame.
P O IN T
Unit to center of the printer. Secure the grounding cables together with the screws.
In the next step, waste ink may spill from the Wasted Ink Tube. Prepare waste cloths
or similar in advance. 3. Disconnect the cable from the relay connector.
1. Slide the tube clamp, and remove the Wasted Ink Tube from the Wasted Ink Duct Holder.

Confidential
Inksystem Unit Inksystem Unit
Hook Pump Encoder Sensor
FFC Acetate tape Inksystem Unit
Slit
Upper Cap FFC Cover Upper Cap FFC Cover
FFC
Guide
Wasted Ink Tube
Slit
Tabs
Inksystem Unit

Pump motor cable
4. Disengage hook, then remove the Upper Cap FFC Cover. 7. Peel off a piece of acetate tape.
Route the FFC through the slit on the Upper Cap FFC Cover. 8. Remove the four screws (S4: ), and remove the Inksystem Unit.
 Route the Wasted Ink Tube through the guide on the Inksystem Unit.
 Route the pump motor cable through the slit on the Inksystem Unit.
5. Disconnect the FFC from the Pump Encoder Sensor.
6. Release the FFC from the three tabs on the Inksystem Unit.

Confidential
Maintenance Box Detect Sensor Assy

C9 Main Board Assy Connector Hooks
Maintenance Box
Detect Sensor Holder FFC Paper Feed Sensor Unit FFC
Top
FFC Main Frame Assy
FFC
No. Screw Type Maintenance Box

S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C Detect Sensor
Double-sided tape
1. Remove the two screws (S4: ) that secure the Maintenance Box Detect Sensor Holder. 2. Disconnect the FFC of the Maintenance Box Detect Sensor from the connector on the Main
Board.
3. Release the FFC from four hooks on the Paper Feed Sensor Unit.
4. Peel off the FFC from the Main Frame Assy and maintenance box slot.

Confidential
Porous Pad Cap Lower

FFC D10
Maintenance Box
Upper Cover
Gap
Porous Pad
Cap Lower
Paper Feed Sensor Unit
Maintenance Box
Detect Sensor Assy
5. Remove the Maintenance Box Detect Sensor Assy from the maintenance box slot. 1. Remove the Porous Pad Cap Lower.
Route in such a way that the FFC terminal (contact surface) is at the side of the Paper
Feed Sensor Unit from the gap of the Maintenance Box Upper Cover.

Confidential
6.2.4.15 Carriage Mechanism (1)
OUTLINE
Time
Total
Extension Spring 11.11 A --- --- ---
CR Scale B --- --- ---
Ink Supply Tube C --- --- ---
Seal Joint Head D --- --- ---

Confidential
Start
Start
C H E C K  As for the procedure indicated by , refer to 6.2.4.4
P O IN T Housing (WF-C5200 Series) (2) (p. 254) in the case of
Preparation for Ink Discharge the WF-C5200 Series, and remove the parts from the
Dissembling (→P. 391) Rear Back Cover to the Housing Top.
 The procedure indicated by is applicable only in the
WF-C5700 Series/ET-8700.
A1 B1 Rear Cover (Back)  Implement the procedure indicated by when
C1 D1 (→P. 392)
removing the Ink Tube from the RIPS Unit and
Printhead.
A2 B2 ASF Front Cover
C2 D2 (→P. 393)
A3 B3 Ink Eject Cover

C3 D3 (→P. 393)
A4 B4 Housing Right
C4 D4 (→P. 394)
A5 B5 Housing Left A8 B8 Extension Spring 11.11 C8 D8 Head Upper Cover

C5 D5 (→P. 394) (→P. 396) (→P. 397)
A6 B6 Housing Upper B9 CR Scale C9 D9 Plate

C6 D6 (→P. 395) (→P. 397) (→P. 398)
A7 B7 ADF/SCN Unit C10 D10 Ink Supply Tube

C7 D7 (→P. 395) (→P. 398)
D11 Seal Joint Head

(→P. 402)

Confidential
Preparation of the Ink Discharge

Preparation for Ink Discharge
Dissembling Lever of the Cover
Open Sensor
Lock Lever
RIPS Front Cover
Ink Pack Tray CL

Ink Pack Tray BK
1. Connect the AC cable to the printer, and turn the printer on. 3. Push the lever of the Cover Open Sensor and secure it with tape.
2. Slide the Lock Lever in the direction of the arrow to open the RIPS Front Cover. 4. Push the Ink Pack Tray BK and Ink Pack Tray CL, then remove them.
5. Make sure the display on the panel LCD does not indicate an error, such as “Cover open
error”, and is in the normal state.
 When securing the lever of the Cover Open Sensor with tape, secure it properly ensuring
there is no peeling of the tape during adjustment. (If the tape peels, the “Cover open error”
will occur and the adjustment process will be interrupted.)
 If the above-described steps 3 and 4 are reversed, an “Ink not delivered error” will occur, and
you will not be able to start the adjustment process.

Confidential
Ink Discharge
A1 B1
Rear Cover (Back)
C1 D1
Rear Cover (Back)
Dowel and Dowel and

No. Screw Type

1. Connect the PC and printer with USB cable. 1. Remove the four screws (S4: ), then remove the Rear Cover (Back).
2. Start the adjustment program. Attach the two dowels of the Rear Cover (Back) to the positioning holes on the
3. Select the Ink Eject from items on the adjustment program. Housing Left and Housing Right.
4. Execute the Ink Eject at following instruction on the adjustment program.
5. After finishing the Ink Discharge, Disconnect the AC cable from the printer to turn the printer off.
 Do not turn OFF the power by pressing the power button as that may cause ink to be re-
charged.
 Since the amount of consumption of ink is not counted, take note of the amount of ink
remaining in the Maintenance Box during Ink Discharge.

Confidential
A2 B2 A3 B3
ASF Front Cover Ink Eject Cover
C2 D2 C3 D3
Hook
ASF Front Cover
Rear Cover (Back)
Ink Eject Cover
No. Screw Type

1. Remove the four screws (S4: ) that secure the ASF Front Cover. 1. Disengage the hook, and remove the Ink Eject Cover.
2. Remove the ASF Front Cover upward while slightly bending the Rear Cover (Back) toward
the back.

Confidential
A4 B4 A5 B5
C4 D4 C5 D5
Rear Rear
Hooks
Housing Left
Housing Right
Hooks
Hooks
Tabs

S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C Tab
1. Open the ADF/SCN Unit. 1. Open the ADF/SCN Unit.

2. Remove the four screws (S4: ) that secure the Housing Right. 2. Remove the three screws (S4: ) that secure the Housing Left.
3. Lift the Housing Right to release the two hooks on the front side of the Housing Right, then 3. Lift the Housing Left to release the two hooks on the front side of the Housing Left.
remove the Housing Right. 4. Disengage two hooks on the rear side of the Housing Left, and remove the Housing Left.
Insert the four tabs of the Housing Right to the positioning holes on the Ink Supply Insert the eight tabs on the Housing Left to the positioning hokes of the Housing
Unit. Upper and the Ink Supply Unit.

Confidential
A6 B6 A7 B7
Housing Upper ADF/SCN Unit
C6 D6 C7 D7
Open Close
Housing
Upper
Connector Lock
Top CN612
CN606
CN601
No. Screw Type

Grounding cable
S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C Acetate tape
1. Remove the six screws (S4: ), then remove the Housing Upper. C H E C K When disconnecting the CISM FFC (CN601) from this connector, make sure to
P O IN T
unlock the connector lock beforehand.
• CN601 • CN606 • CN612 • CN801


Confidential
ADF/SCN Unit
A8 B8
Extension Spring 11.11
ADF/SCN Unit 45 °
CR Scale
Extension Spring 11.11
Main Frame
No. Screw Type

3. Open the ADF/SCN Unit. 1. Remove the Extension Spring 11.11 from the CR Scale.
4. Remove the two screws (S4: ), then remove the ADF/SCN Unit in the direction of the 2. Remove the Extension Spring 11.11 from the Main Frame.
arrow.

Confidential
B9
CR Scale Head Upper Cover
C8 D8
Full side Side view CR Encoder Home side Tabs and positioning holes
Sensor
Hook
Head Upper Cover
CR Scale Hook
CR Unit CR Scale
Ink Tube
Joint Cover
Hook Rib
No. Screw Type

S7 C.B.P-TITE-SCREW-3x10-F.ZB-3C
Marking Film S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C
1. At the full side, remove the CR Scale from hook on the frame. 1. Remove the two screws (S7: ), and remove the Head Upper Cover.
2. Pull the CR Scale out from the CR Encoder Sensor. Attach the two tabs on the Head Upper Cover to the positioning holes of the CR Unit.
3. At the home side, turn the CR Scale 90 degrees upward, and remove it from the hook on the
frame.
Attach the CR Scale with the marking on the bottom right corner. 2. Remove the two screws (S4: ), and remove the Ink Tube Joint Cover.
3. Remove the film from the hook on the Ink Tube Joint Cover.
Set the film under the rib of the Ink Tube Joint Cover.

Confidential
Plate Ink Supply Tube

C9 D9 C10 D10
Plate
Plate
Ink Supply Tube

S6 C.B.SCREW-2.6X18-F.ZN-3C S8 C.B.EP-TITE SCREW,2.6X17(B=14),F/ZN-3C
1. Remove the two screws (S6: ), and remove the Plate. In the following steps, ink may spill from the Ink Supply Tube. Prepare waste cloths
When installing the Ink Supply Tube to the RIPS Unit, make sure to tighten the or similar in advance.
screws using a torque driver with the specified torque.
 Screw tightening torque: 0.59±0.01Nm
1. Remove the two screws (S8: ), and remove the Ink Supply Tube from the Printhead.
Make sure the plate was attached.

Confidential
Ink Supply Tube Ink Supply Tube
Tube Clamp Tube Holder Hook Ink Supply Tube
87.5 ± 1 mm
Ink Supply Tube
Joint
Marking Hook
No. Screw Type

2. Remove the Ink Supply Tube from the Tube Clamp. 4. Remove the screw (S4: ).
At the marking point on the Ink Supply Tube, attach the Ink Supply Tube to the Tube 5. Remove the Ink Supply Tube from the Joint, and remove the Ink Supply Tube.
Clamp. If the marking is not visible, refer to the drawing above to attach the Ink
Supply Tube.
3. Remove the Tube Holder while pressing the hooks outward.

Confidential
Ink Supply Tube Ink Supply Tube
 Types of Ink Leak Measurement Jig

Rear side Right side
Part Name Part Code Photo Remark
LEAK TESTER 1684353
Smoked
SHEET FRONT Face
10mm
LEAK TESTER 1684354

Smoked
SHEET REAR Face
Bottom
15mm
90°
Ink Leak Measurement Jig
Left side Front side
90°
Make sure to clean the Ink tube joint part of Printhead by using the Cleaning stick, In this product, Ink Leak Check is necessary to prevent the ink leakage due to
because perform the Ink Leak Check correctly. assembly mistake.
Therefore, make sure to install the ink leak measurement jig when installing the Ink
If ink is remained to ink tube joint part of Printhead, Ink Leak Check can not perform Tube to Printhead.
correctly. Before using the Leak Check Jig, push the ink leak measurement jig along the folds
Therefore cleaning the ink surely. until the fold angle become 90 degrees.

Confidential

Epson WF C5790 WF C5790A WF C5710 ET 8700 WF C5210 WF C5290 WF C5290A Service Manuals 351 400

Uploaded by

Copyright:

Available Formats

Epson WF C5790 WF C5790A WF C5710 ET 8700 WF C5210 WF C5290 WF C5290A Service Manuals 351 400

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Epson WF C5790 WF C5790A WF C5710 ET 8700 WF C5210 WF C5290 WF C5290A Service Manuals 351 400

Uploaded by

Copyright:

Available Formats

EPSON WF-C5790/WF-C5790a/WF-C5710/ET-8700/WF-C5210/WF-C5290/WF-C5290a Revision A

No. Screw Type No. Screw Type

Disassembly/assembly Disassembly/Reassembly Procedures 351

Rear ASF sensor cable/

No. Screw Type

Disassembly/assembly Disassembly/Reassembly Procedures 352

Grounding cable No. Screw Type

Disassembly/assembly Disassembly/Reassembly Procedures 353

Hinge Assy Hinge Lower Cover

Hinge Lower Hinge Lower

Hinge Lower Cover

No. Screw Type No. Screw Type

Disassembly/assembly Disassembly/Reassembly Procedures 354

Rear ASF Assy

Rear ASF Assy

Rear ASF Assy

Photo interrupter cable

Disassembly/assembly Disassembly/Reassembly Procedures 355

PS Ground Plate Rear ASF Upper Guide Assy

No. Screw Type No. Screw Type

Disassembly/assembly Disassembly/Reassembly Procedures 356

Power Supply Assy

Ferrite Core Ferrite Core

Slit Power Supply Assy Slit

AC Cable Hook Slit Hook Guide

Rea ASF Upper Guide Assy

No. Screw Type

Disassembly/assembly Disassembly/Reassembly Procedures 357

6.2.4.12 Electrical Components (3) (WF-C5700 Series/ET-8700)

Panel Assy A --- --- ---

Numpad Board Assy B --- --- ---

Panel Board C --- --- ---

Relay Cable (Panel to

Relay Cable (Panel to

Disassembly/assembly Disassembly/Reassembly Procedures 358

A1 B1 C1 Rear Cover (Back)

A2 B2 C2 ASF Front Cover

A3 B3 C3 Ink Eject Cover

Disassembly/assembly Disassembly/Reassembly Procedures 359

Rear Cover (Back)

ASF Front Cover

Dowel and Dowel and

Housing Right Housing Left

No. Screw Type No. Screw Type

Disassembly/assembly Disassembly/Reassembly Procedures 360

Ink Eject Cover

No. Screw Type

Disassembly/assembly Disassembly/Reassembly Procedures 361

No. Screw Type No. Screw Type

Disassembly/assembly Disassembly/Reassembly Procedures 362

Rear ASF sensor cable/

No. Screw Type

Disassembly/assembly Disassembly/Reassembly Procedures 363

Right Panel Holder

Bearing Shaft Panel Assy

No. Screw Type

Disassembly/assembly Disassembly/Reassembly Procedures 364

Numpad Board Assy Panel Board