Flender ARPEX Couplings PDF

6
© Siemens AG 2015
Torsionally Rigid
All-Steel Couplings
ARPEX Series
6/2 ARPEX Series - General information 6/37 ARPEX ARP-6 Series

6/2 Overview 6/37 Overview
6/2 Design 6/37 Benefits
6/37 Application
6/4 ARPEX ARS-6 Series
6/38 Design
6/4 Overview
6/38 Technical data
6/4 Benefits
6/40 • Type NAN
6/4 Application 6/40 Selection and ordering data
6/5 Design 6/42 • Type MCECM
6/6 Technical data 6/42 Selection and ordering data
6/8 • Type NEN 6/45 Spare and wear parts
6/8 Selection and ordering data 6/45 • Plate pack ARP-6
6/10 • Type NUN 6/45 Selection and ordering data
6/10 Selection and ordering data
6/12 • Type NON 6/46 ARPEX ARW-4/-6 Series
6/12 Selection and ordering data 6/46 Overview
6/14 • Type NHN 6/46 Benefits
6/14 Selection and ordering data 6/46 Application
6
6/16 • Type NZN 6/46 Design
6/16 Selection and ordering data 6/47 Technical data
6/18 • Type NWN 6/48 • Type NHN
6/18 Selection and ordering data 6/48 Selection and ordering data
6/20 Further hubs and flanges 6/50 Spare and wear parts
6/20 • J hub 6/50 • Plate pack ARW-4/-6
6/20 Selection and ordering data 6/50 Selection and ordering data
6/22 • F flange, D flange, C flange
6/51 ARPEX ARF-6 Series
6/51 Overview
6/24 • Clamping hub
6/51 Benefits
6/51 Application
6/26 Spare and wear parts
6/51 Design
6/26 • Plate pack ARS-6
6/52 Technical data
6/53 • Types GG and GJ
6/27 ARPEX ARC-8/-10 Series 6/53 Selection and ordering data
6/27 Overview 6/54 Spare and wear parts
6/27 Benefits 6/54 • Plate pack ARF-6
6/27 Application 6/54 Selection and ordering data
6/28 Design
6/29 Technical data
6/30 • Types NEN/NHN
6/32 • Type BUB
6/34 • Types MFEFM/MFHFM
6/36 Spare and wear parts
A.G.P. Representaciones S.A.S 6/36 • Plate pack ARC-8/-10
Calle 21A No. 70 - 40, Bodega UA 7 - 1
Bogota, Colombia 6/36 Selection and ordering data
Tel. : +57 1 5706353
Fax : +57 1 5707335
[email protected]
www.agp.com.co
Siemens MD 10.1 · 2015

© Siemens AG 2015
FLENDER Standard Couplings

Torsionally Rigid All-Steel Couplings — ARPEX Series
General information
■ Overview
Thanks to a large number of standard components ARPEX cou-
plings can be combined to make many different types. In this
way, standard types can be used with many drives.
ARPEX couplings can withstand temperatures between
-40 °C and +280 °C in operation. On request, they can also be
specially equipped for use in other temperature ranges.
Coupling suitable for use in potentially explosive

atmospheres.
Complies with the current ATEX Directive for:
II 2G T2/T3/T4/T5/T6
-40 °C ≤ Ta ≤ +230 °C/+150 °C/+85 °C/+50 °C/+35 °C
II 2D T 120 °C -40 °C ≤ Ta ≤ +70 °C

ARPEX couplings have proved themselves for over 30 years in
all areas of technology where reliable, maintenance-free torque
transmission is required. ARPEX couplings link machine shafts I M2
6
and compensate for shaft misalignments, while generating only

low restorative forces. Thanks to the use of spring steel plates
and backlash-free screw connections, ARPEX couplings are tor-
sionally rigid and backlash-free. All ARPEX coupling compo-
nents are manufactured from high-quality steel. Robust, com-
pact construction guaranteeing a high level of operational To meet the high quality demands made of ARPEX couplings,
reliability and a long service life is therefore possible. High-pre- the development and manufacture of ARPEX couplings is inte-
cision production ensures that at speed in the assembled condi- grated into a certified quality management system in accor-
tion only low forces act on the machine parts connected to them. dance with the requirements of DIN EN ISO 9001.
ARPEX couplings can be used for both directions of rotation and
are thus also suitable for reverse operation. Type approval for use of ARPEX couplings in shipbuilding has
been issued by the following classification societies: American
ARPEX couplings are not subject to wear and, if correctly de- Bureau of Shipping (ABS), Det Norske Veritas (DNV), Ger-
signed, assembled and installed, can be expected to have an manischer Lloyd (GL) and Lloyd's Register of Shipping. Product
unlimited service life. With most types the intermediate spacer certification to GOST-R for the Russian market has already been
can be fitted radially without having to move the driving and obtained.
driven machines.
■ Design
ARPEX couplings are manufactured completely from steel. Plate pack
Torque is transmitted by means of torsionally rigid, flexible
plates. The plates are held together by a sleeve and ring to form The flexible elements in an ARPEX coupling take the form of
a compact plate pack. This ensures easy, operationally safe in- plate packs. The individual, thin plates are held together by a
stallation. Two plate packs fastened alternately to the flanges socket and ring to form a compact plate pack. The picture below
permit compensation of shaft misalignments in an angular, radial shows the structure of a ring plate pack.
and axial direction. On coupling types with a single plate pack
only angular and axial misalignments are possible.
Materials
All coupling parts like hubs, spacers and flanges are manufac-
tured from high-grade steel; the plates are made from stainless,
hard-rolled CrNi spring steel. Bolts and nuts are of quality 10.9
or 10. Plate
Socket
Application
Ring
ARPEX couplings are available as a catalog standard from
92 Nm to 1450000 Nm and are divided into various series. Be-
cause of this series diversity, ARPEX couplings meet most
torque and speed requirements as a universal coupling solution
in general mechanical engineering. The individual series and
their corresponding possible applications are described in full in
the following sections.
G_MD10_EN_00140
6/2 Siemens MD 10.1 · 2015

© Siemens AG 2015

Torsionally Rigid All-Steel Couplings — ARPEX Series
General information
Plate pack screw connection
Patented1) conical screw connection
Before tightening the screw connection After tightening the screw connection
Tightening screw
Screw plug
Washer
Taper bolt
Taper sleeve ARPEX flange
G_MD10_EN_00141a
ARPEX flange
Plate pack
1) Protected by patent in a number of countries on the date of creation of this catalog.
6
Features of plate pack screw connection
Up to bolt size M22, the plate pack screw connection on ARPEX
Close-fitting bolt connection couplings is in the form of a close-fitting bolt connection. After
that the patented 1) conical screw connection is used. The deci-
Close-fitting bolt sive advantage of this screw connection is considerably simpli-
fied fitting. The use of an hydraulic fitting tool is no longer neces-
sary. All sizes can be fitted with a torque wrench.
G_MD10_EN_00142a
A further feature of the conical screw connection is the genuine

positive connection resulting in high centering accuracy and,
thus, a high balancing quality. Material: High-grade quenched
and tempered steel.
The conical screw connection is used for the following coupling
Collar nut Plate pack sizes:
ARS-6 series: size 305-6 to 602-6
ARPEX flange ARPEX flange ARC-8/-10 series: all sizes
ARP-6 series: type NAN, size 325-6;
type MCECM, size 310 and 345-6
ARW-4/-6 series: size 324-4 to 880-6
1)
Protected by patent in a number of countries on the date of creation of
this catalog.
Siemens MD 10.1 · 2015 6/3

© Siemens AG 2015

Torsionally Rigid All-Steel Couplings — ARPEX ARS-6 Series
General information
■ Overview
Coupling suitable for use in potentially explosive

atmospheres.
■ Benefits
6
ARPEX couplings of the ARS-6 series are outstanding for their

versatility. Most standard components are available from stock,
resulting in short delivery times. Their use in potentially explosive
atmospheres in accordance with the current ATEX Directive is
possible.
■ Application
ARPEX couplings of the ARS-6 series are a versatile coupling
solution which thanks to standard modular components can be
used for most drive requirements at a low to medium speed.
Torques of between 170 and 106000 Nm can be transmitted at
a permitted angular misalignment of 0.7°. The open flange form
is regarded as very easy to fit and has easily accessible screw
connection points. On most types, the intermediate spacer can
be radially fitted without moving the connected units.
Main areas of application for the ARS-6 series:
• Paper-making machines
• Printing machines
• Compressors
• Pumps
• Fans and blowers
• Film and foil machines
• Generators
• Presses
• Metalworking machines
• Conveyors
• Crane systems
• Textile machines
• Plastics processing machines
• Centrifuges
6/4 Siemens MD 10.1 · 2015

© Siemens AG 2015

General information
■ Design
The classic design of an ARPEX couplings of the ARS-6 series is 305-6 conical screw connections are used for fastening. A large
shown in the following illustration. The plate packs are bolted al- number of intermediate spacer and shafts, hubs and flanges
ternately between the flanges of the coupling hubs and the inter- can be combined and thus cover a large number of possible
mediate spacer. Up to size 280-6 close-fitting bolts and from size drive requirements.
Hub
Intermediate spacer
Hub
Close-fitting bolt
6
Plate pack
Collar nut
G_MD10_EN_00143a
Design of an ARPEX coupling, ARS-6 series, type NEN

Variants of the ARPEX coupling, ARS-6 series
Types
All coupling types can be very easily combined with further stan-
dard components in the ARPEX modular system. Jumbo hubs
NEN, BEN, BEB Variant with standard intermediate spacer, many sizes
available from stock are used to permit larger maximum bores.
NON, BON Variant with shortest intermediate spacer
Clamping hubs transmit torque by friction without the use of par-
allel keys.
NUN, BUN, BUB Variant with split intermediate spacer
F, D and C flanges offer many different possibilities for flange
NHN Variant with intermediate spacer for customer-specific connection.
shaft distance
NZN Variant with reinforced intermediate spacer The coupling parts of the ARPEX ARS-6 series are machined on
NWN Variant with intermediate shaft all sides. Exceptions are H and Z spacers and intermediate
shafts. The spacers are delivered with unmachined, primed
spacer tube.
Higher torques and maximum speeds with similar coupling outer
diameters DA can be achieved with the ARPEX ARC-8/-10
series.
Further application-specific coupling types are available in
selection module X.CAT NG at www.siemens.com/couplings.
Dimension sheets and further information are available on
request.
Siemens MD 10.1 · 2015 6/5

© Siemens AG 2015

General information
■ Technical data
Power ratings
Size Rated Maxi- Over- Fatigue Maxi- Maximum permitted shaft misalignment Torsional stiffness
torque mum load torque mum
torque torque speed
DA TKN TKmax TKOL TKW nKmax ±ΔKa ±ΔKw ±ΔKr CTdyn
NHN NEN/BEN NON NEN NUN NON NHN NZN NWN
NZN BEB/NUN BON BEN/BEB BUN/BUB BON
NWN BUN/BUB
Nm Nm Nm Nm rpm mm mm mm mm MNm/rad MNm/rad MNm/rad MNm/rad MNm/rad MNm/rad
78-6 170 320 510 85 13400 1.10 0.7° 12.1 0.57 0.53 0.05 0.04 0.05 0.012 0.032 0.05
105-6 270 510 810 135 10000 1.80 12.1 0.88 0.53 0.09 0.09 0.09 0.024 0.070 0.09
125-6 490 930 1470 245 8400 2.02 12.1 1.04 0.68 0.17 0.17 0.18 0.043 0.141 0.19
140-6 700 1330 2100 350 7500 2.40 12.1 1.28 0.72 0.22 0.22 0.24 0.066 0.203 0.25
165-6 1250 2370 3750 625 6350 2.74 12.0 1.49 0.84 0.33 0.34 0.36 0.114 0.317 0.39
175-6 2000 3800 6000 1000 6000 2.86 12.0 1.55 0.98 0.48 0.50 0.52 0.196 0.443 0.57
195-6 3000 5700 9000 1500 5350 3.06 12.0 1.55 0.98 0.67 0.69 0.73 0.302 0.614 0.79
210-6 4400 8300 13200 2200 5000 3.14 12.0 1.77 1.10 0.77 0.78 0.82 0.352 0.669 0.88
240-6 5700 10800 17100 2850 4350 3.70 12.0 1.93 1.20 1.24 1.26 1.32 0.568 1.04 1.40
255-6 7600 14400 22800 3800 4100 3.84 11.9 2.09 1.50 1.39 1.42 1.46 0.697 1.22 1.57
6
280-6 10000 19000 30000 4600 3750 4.18 11.9 2.53 1.53 1.55 1.57 1.65 0.881 1.42 1.73
305-6 12000 21000 36000 5000 3400 4.46 11.9 2.72 1.80 2.83 2.87 3.05 1.51 2.71 3.32
335-6 18000 32000 54000 7500 3100 4.84 11.9 2.88 1.89 3.85 3.92 4.14 2.11 3.62 4.49
372-6 24000 43000 72000 10000 2800 4.98 11.8 3.03 2.16 5.72 5.84 6.12 3.14 – 6.75
407-6 34000 61000 102000 14000 2550 5.50 11.8 3.31 2.26 7.25 7.42 7.79 5.06 – 8.51
442-6 43000 77000 129000 18000 2350 6.02 11.8 3.59 2.48 10.0 10.2 10.8 7.42 – 11.9
487-6 55000 99000 165000 23000 2150 6.80 11.7 4.09 2.64 11.7 11.9 12.7 9.25 – 13.6
522-6 69000 124000 207000 29000 2000 7.34 11.7 4.35 2.86 14.0 14.3 15.1 11.4 – 16.2
572-6 92000 166000 276000 38000 1800 7.86 11.6 4.87 3.02 17.9 18.3 19.4 15.2 – 20.7
602-6 106000 191000 318000 44000 1700 8.24 11.6 5.13 3.24 21.1 21.7 22.9 18.2 – 24.5
The permitted shaft misalignments ΔKa, ΔKr and ΔKw are maxi- The values for torsional stiffness apply to the complete coupling.
mum values and must not occur at the same time (see following In the case of types NHN and NZN to a coupling with shaft dis-
table). tance S = 1000 mm. In the case of type NWN, the torsional stiff-
The permitted shaft misalignment ΔKr for types NHN, NZN and ness applies to a coupling without intermediate or torsion shaft.
NWN applies to a coupling with shaft distance S = 1000 mm. The torsional stiffness of the plate packs applies to the rated
For other shaft distances, the permitted radial misalignment can coupling torque TKN. To determine the torsional stiffness for a
be determined with the following formula: specific operating point, e.g. for calculating torsional vibration,
ΔKr = (S – S1) ⋅ tan (ΔKw). the manufacturer must be consulted.
The shaft distance S is shown in the table for the type.
TKmax permitted only five times per hour.
6/6 Siemens MD 10.1 · 2015

© Siemens AG 2015

General information
Permitted shaft misalignments
Size Permitted angular misalignment ±ΔKw
0.0° 0.1° 0.2° 0.3° 0.4° 0.5° 0.6° 0.7°
DA Permitted axial misalignment ±ΔKa in mm
78-6 1.10 0.94 0.79 0.63 0.47 0.31 0.16 0.00
105-6 1.80 1.54 1.29 1.03 0.77 0.51 0.26 0.00
125-6 2.02 1.73 1.44 1.15 0.87 0.58 0.29 0.00
140-6 2.40 2.06 1.71 1.37 1.03 0.69 0.34 0.00
165-6 2.74 2.35 1.96 1.57 1.17 0.78 0.39 0.00
175-6 2.86 2.45 2.04 1.63 1.23 0.82 0.41 0.00
195-6 3.06 2.62 2.19 1.75 1.31 0.87 0.44 0.00
210-6 3.14 2.69 2.24 1.79 1.35 0.90 0.45 0.00
240-6 3.70 3.17 2.64 2.11 1.59 1.06 0.53 0.00
255-6 3.84 3.29 2.74 2.19 1.65 1.10 0.55 0.00
280-6 4.18 3.58 2.99 2.39 1.79 1.19 0.60 0.00
305-6 4.46 3.82 3.19 2.55 1.91 1.27 0.64 0.00
335-6 4.84 4.15 3.46 2.77 2.07 1.38 0.69 0.00
372-6 4.98 4.27 3.56 2.85 2.13 1.42 0.71 0.00
407-6 5.50 4.71 3.93 3.14 2.36 1.57 0.79 0.00
442-6 6.02 5.16 4.30 3.44 2.58 1.72 0.86 0.00
487-6 6.80 5.83 4.86 3.89 2.91 1.94 0.97 0.00
522-6 7.34 6.29 5.24 4.19 3.15 2.10 1.05 0.00
6
572-6 7.86 6.74 5.61 4.49 3.37 2.25 1.12 0.00
602-6 8.24 7.06 5.89 4.71 3.53 2.35 1.18 0.00
Siemens MD 10.1 · 2015 6/7

© Siemens AG 2015

Type NEN
■ Selection and ordering data

Torsionally rigid coupling type NEN with radially freely dismountable intermediate spacer. Types BEN and BEB cannot be dismounted
radially without moving the units. On type BEB, the smallest possible shaft distance can be achieved.
LG
A S
LG
G_MD10_XX_00144
ØND2
NL1 S NL2
ØND1
ØD2
ØD1
S1
SZ
P B E N
ØND1
ØND2
ØDZ
ØDA
ØD1
ØD2
LG
A S
6
N E N
ØND2
ØND1
ØD2
ØD1
P B E B
Size Rated Maxi- Type Dimensions in mm Mass Article No. Weight

torque mum Shaft moment Order codes for bore
speed dis- of diameters and tolerances
tance inertia are specified in catalog
DA TKN nKmax D1, D2 ND1 ND2 DZ SZ NL1/ S1 S A P LG J section 3 m
Keyway NL2
DIN 6885
mm Nm rpm max. max. kgm2 kg
78-6 170 13400 NEN 28 28 39 39 45 2.5 30 8 55 – – 115 0.001 2LC0470-0NS ■ ■ -0AA0 1.2
BEN 32 8 29 92 2LC0470-0AK ■ ■ -0AA0
BEB 9 69 2LC0470-0AC ■ ■ -0AA0
105-6 270 10000 NEN 45 45 63 63 72 2.5 45 8 80 – – 170 0.003 2LC0470-1NS ■ ■ -0AA0 2.5
BEN 42 8 29 132 2LC0470-1AK ■ ■ -0AA0
BEB 4 94 2LC0470-1AC ■ ■ -0AA0
125-6 490 8400 NEN 55 55 76 76 84 2.5 55 11 96 – – 206 0.009 2LC0470-2NS ■ ■ -0AA0 4.5
BEN 50 10 37 160 2LC0470-2AK ■ ■ -0AA0
BEB 4 114 2LC0470-2AC ■ ■ -0AA0
140-6 700 7500 NEN 65 65 91 91 99 2.5 65 11 116 – – 246 0.015 2LC0470-3NS ■ ■ -0AA0 6.4
BEN 60 10 37 190 2LC0470-3AK ■ ■ -0AA0
BEB 4 134 2LC0470-3AC ■ ■ -0AA0
165-6 1250 6350 NEN 75 75 105 105 114 2.5 75 14 136 – – 286 0.032 2LC0470-4NS ■ ■ -0AA0 9.7
BEN 70 12 45 220 2LC0470-4AK ■ ■ -0AA0
BEB 4 154 2LC0470-4AC ■ ■ -0AA0
175-6 2000 6000 NEN 80 80 110 110 120 3.0 80 15 142 – – 302 0.048 2LC0470-5NS ■ ■ -0AA0 12.5
BEN 74 15 52 234 2LC0470-5AK ■ ■ -0AA0
BEB 6 166 2LC0470-5AC ■ ■ -0AA0
195-6 3000 5350 NEN 90 90 120 120 131 3.0 80 15 142 – – 302 0.073 2LC0470-6NS ■ ■ -0AA0 14.9
BEN 74 14 52 234 2LC0470-6AK ■ ■ -0AA0
BEB 6 166 2LC0470-6AC ■ ■ -0AA0
6/8 Siemens MD 10.1 · 2015

© Siemens AG 2015

Type NEN
Keyway NL2
DIN 6885
210-6 4400 5000 NEN 95 95 126 126 139 4.0 90 15 160 – – 340 0.109 2LC0470-7NS ■ ■ -0AA0 19.5
BEN 83 20 61 263 2LC0470-7AK ■ ■ -0AA0
BEB 6 186 2LC0470-7AC ■ ■ -0AA0
240-6 5700 4350 NEN 110 110 145 145 162 5.0 100 18 176 – – 376 0.210 2LC0470-8NS ■ ■ -0AA0 28.4
BEN 91 18 66 291 2LC0470-8AK ■ ■ -0AA0
BEB 6 206 2LC0470-8AC ■ ■ -0AA0
255-6 7600 4100 NEN 115 115 154 154 170 5.0 110 23 194 – – 414 0.315 2LC0471-0NS ■ ■ -0AA0 37.5
BEN 102 24 81 322 2LC0471-0AK ■ ■ -0AA0
BEB 10 230 2LC0471-0AC ■ ■ -0AA0
280-6 10000 3750 NEN 135 135 184 184 186 6.0 130 25 232 – – 492 0.542 2LC0471-1NS ■ ■ -0AA0 54.5
BEN 120 135 161 184 121 22 83 381 0.514 2LC0471-1AK ■ ■ -0AA0 52.1
BEB 120 120 161 161 10 270 0.486 2LC0471-1AC ■ ■ -0AA0 49.7
305-6 12000 3400 NEN 145 145 198 198 200 6.5 140 27 250 – – 530 0.762 2LC0471-2NS ■ ■ -0AA0 66.4
BEN 130 145 175 198 130 13 61 410 0.724 2LC0471-2AK ■ ■ -0AA0 63.6
BEB 130 130 175 175 10 290 0.685 2LC0471-2AC ■ ■ -0AA0 60.9
6
335-6 18000 3100 NEN 160 160 214 214 218 7.5 150 30 266 – – 566 1.18 2LC0471-3NS ■ ■ -0AA0 84.2
BEN 140 160 190 214 138 15 69 438 1.13 2LC0471-3AK ■ ■ -0AA0 82.1
BEB 140 140 190 190 10 310 1.08 2LC0471-3AC ■ ■ -0AA0 80.0
372-6 24000 2800 NEN 165 165 225 225 228 9.5 160 32 280 – – 600 1.93 2LC0471-4NS ■ ■ -0AA0 116
BEN 145 165 200 225 145 16 76 465 1.87 2LC0471-4AK ■ ■ -0AA0 113
BEB 145 145 200 200 10 330 1.80 2LC0471-4AC ■ ■ -0AA0 110
407-6 34000 2550 NEN 185 185 250 250 245 11.0 175 35 306 – – 656 3.06 2LC0471-5NS ■ ■ -0AA0 152
BEN 145 185 205 250 158 19 83 508 2.91 2LC0471-5AK ■ ■ -0AA0 148
BEB 145 145 205 205 10 360 2.76 2LC0471-5AC ■ ■ -0AA0 144
442-6 43000 2350 NEN 200 200 270 270 273 11.0 190 38 332 – – 712 4.58 2LC0471-6NS ■ ■ -0AA0 192
BEN 170 200 230 270 172 20 92 552 4.38 2LC0471-6AK ■ ■ -0AA0 185
BEB 170 170 230 230 12 392 4.18 2LC0471-6AC ■ ■ -0AA0 178
487-6 55000 2150 NEN 225 225 305 305 298 13.0 215 41 376 – – 806 7.73 2LC0471-7NS ■ ■ -0AA0 268
BEN 180 225 250 305 194 23 100 624 7.32 2LC0471-7AK ■ ■ -0AA0 258
BEB 180 180 250 250 12 442 6.91 2LC0471-7AC ■ ■ -0AA0 248
522-6 69000 2000 NEN 240 240 325 325 324 13.0 230 44 400 – – 860 10.7 2LC0471-8NS ■ ■ -0AA0 323
BEN 200 240 275 325 206 23 107 666 10.2 2LC0471-8AK ■ ■ -0AA0 312
BEB 200 200 275 275 12 472 9.72 2LC0471-8AC ■ ■ -0AA0 301
572-6 92000 1800 NEN 265 265 360 360 356 15.0 255 47 446 – – 956 17.1 2LC0472-0NS ■ ■ -0AA0 431
BEN 220 265 300 360 229 24 114 739 16.2 2LC0472-0AK ■ ■ -0AA0 413
BEB 220 220 300 300 12 522 15.2 2LC0472-0AC ■ ■ -0AA0 394
602-6 106000 1700 NEN 280 280 380 380 368 16.0 270 50 470 – – 1010 22.6 2LC0472-1NS ■ ■ -0AA0 514
BEN 225 280 310 380 241 26 123 781 21.3 2LC0472-1AK ■ ■ -0AA0 492
BEB 225 225 310 310 12 552 20.0 2LC0472-1AC ■ ■ -0AA0 470
∅D1: • Without finished bore – Without order codes 1
• With finished bore – With order codes for diameter and tolerance (article number without "-Z") 9
Torsionally rigid ARPEX couplings up to size 240-6 available Ordering example:
from stock. ARPEX ARS-6 NEN coupling, size 105-6,
bore ∅D1 40H7 mm, with keyway to DIN 6885 and set screw,
For simplified fitting on B hubs, plate packs from size 280-6 bore ∅D2 45K7 mm, with keyway to DIN 6885 and set screw.
available with closing element.
Article No.:
Weights and mass moments of inertia apply to the entire 2LC0470-1NS99-0AA0-Z
coupling with maximum bores D1/D2. L0W+M1A+M13
Siemens MD 10.1 · 2015 6/9

© Siemens AG 2015

Type NUN

Torsionally rigid coupling type NUN with radially freely dismountable intermediate spacer. Types BUN and BUB cannot be radially
dismounted without moving the units. On type BUB, the smallest possible shaft distance can be achieved.
LG
A S
ØND1
ØND2
ØD1
ØD2
LG
G_MD10_XX_00145
NL1 S NL2
S1
SZ
P B U N
ØND1
ØND2
ØDZ
ØDA
ØD1
ØD2
LG
A S
6
ØND1
ØND2
ØD1
ØD2
N U N
P B U B

speed dis- of inertia diameters and tolerances
tance are specified in catalog
Keyway NL2
DIN 6885
78-6 170 13400 NUN 28 28 39 39 45 2.5 30 8 84 – – 144 0.001 2LC0470-0NW ■ ■ -0AA0 1.5
BUN 61 8 29 121 2LC0470-0BD ■ ■ -0AA0
BUB 38 98 2LC0470-0AT ■ ■ -0AA0
105-6 270 10000 NUN 45 45 63 63 72 2.5 45 8 90 – – 180 0.004 2LC0470-1NW ■ ■ -0AA0 2.9
BUN 52 8 29 142 2LC0470-1BD ■ ■ -0AA0
BUB 14 104 2LC0470-1AT ■ ■ -0AA0
125-6 490 8400 NUN 55 55 76 76 84 2.5 55 11 116 – – 226 0.011 2LC0470-2NW ■ ■ -0AA0 5.3
BUN 70 10 37 180 2LC0470-2BD ■ ■ -0AA0
BUB 24 134 2LC0470-2AT ■ ■ -0AA0
140-6 700 7500 NUN 65 65 91 91 99 2.5 65 11 116 – – 246 0.019 2LC0470-3NW ■ ■ -0AA0 7.2
BUN 60 10 37 190 2LC0470-3BD ■ ■ -0AA0
BUB 4 134 2LC0470-3AT ■ ■ -0AA0
165-6 1250 6350 NUN 75 75 105 105 114 2.5 75 14 136 – – 286 0.038 2LC0470-4NW ■ ■ -0AA0 10.9
BUN 70 12 45 220 2LC0470-4BD ■ ■ -0AA0
BUB 4 154 2LC0470-4AT ■ ■ -0AA0
175-6 2000 6000 NUN 80 80 110 110 120 3.0 80 15 142 – – 302 0.057 2LC0470-5NW ■ ■ -0AA0 14.1
BUN 74 15 52 234 2LC0470-5BD ■ ■ -0AA0
BUB 6 166 2LC0470-5AT ■ ■ -0AA0
195-6 3000 5350 NUN 90 90 120 120 131 3.0 80 15 142 – – 302 0.085 2LC0470-6NW ■ ■ -0AA0 16.8
BUN 74 14 52 234 2LC0470-6BD ■ ■ -0AA0
BUB 6 166 2LC0470-6AT ■ ■ -0AA0
6/10 Siemens MD 10.1 · 2015

© Siemens AG 2015

Type NUN
speed dis- of inertia diameters and tolerances
tance are specified in catalog
Keyway NL2
DIN 6885
210-6 4400 5000 NUN 95 95 126 126 139 4.0 90 15 160 – – 340 0.128 2LC0470-7NW ■ ■ -0AA0 21.9
BUN 83 20 61 263 2LC0470-7BD ■ ■ -0AA0
BUB 6 186 2LC0470-7AT ■ ■ -0AA0
240-6 5700 4350 NUN 110 110 145 145 162 5.0 100 18 176 – – 376 0.242 2LC0470-8NW ■ ■ -0AA0 31.5
BUN 91 18 66 291 2LC0470-8BD ■ ■ -0AA0
BUB 6 206 2LC0470-8AT ■ ■ -0AA0
255-6 7600 4100 NUN 115 115 154 154 170 5.0 110 23 194 – – 414 0.363 2LC0471-0NW ■ ■ -0AA0 41.6
BUN 102 24 81 322 2LC0471-0BD ■ ■ -0AA0
BUB 10 230 2LC0471-0AT ■ ■ -0AA0
280-6 10000 3750 NUN 135 135 184 184 186 6.0 130 25 232 – – 492 0.611 2LC0471-1NW ■ ■ -0AA0 59.4
BUN 120 135 161 184 121 22 83 381 0.583 2LC0471-1BD ■ ■ -0AA0 57.0
BUB 120 120 161 161 10 270 0.555 2LC0471-1AT ■ ■ -0AA0 54.6
305-6 12000 3400 NUN 145 145 198 198 200 6.5 140 27 250 – – 530 0.861 2LC0471-2NW ■ ■ -0AA0 72.4
BUN 130 145 175 198 130 13 61 410 0.823 2LC0471-2BD ■ ■ -0AA0 69.6
BUB 130 130 175 175 10 290 0.784 2LC0471-2AT ■ ■ -0AA0 66.8
6
335-6 18000 3100 NUN 160 160 214 214 218 7.5 150 30 266 – – 566 1.35 2LC0471-3NW ■ ■ -0AA0 93.1
BUN 140 160 190 214 138 15 69 438 1.31 2LC0471-3BD ■ ■ -0AA0 91.0
BUB 140 140 190 190 10 310 1.26 2LC0471-3AT ■ ■ -0AA0 88.9
372-6 24000 2800 NUN 165 165 225 225 228 9.5 160 32 280 – – 600 2.21 2LC0471-4NW ■ ■ -0AA0 127
BUN 145 165 200 225 145 16 76 465 2.15 2LC0471-4BD ■ ■ -0AA0 125
BUB 145 145 200 200 10 330 2.09 2LC0471-4AT ■ ■ -0AA0 122
407-6 34000 2550 NUN 185 185 250 250 245 11.0 175 35 306 – – 656 3.55 2LC0471-5NW ■ ■ -0AA0 170
BUN 145 185 205 250 158 19 83 508 3.40 2LC0471-5BD ■ ■ -0AA0 166
BUB 145 145 205 205 10 360 3.25 2LC0471-5AT ■ ■ -0AA0 161
442-6 43000 2350 NUN 200 200 270 270 273 11.0 190 38 332 – – 712 5.29 2LC0471-6NW ■ ■ -0AA0 213
BUN 170 200 230 270 172 20 92 552 5.09 2LC0471-6BD ■ ■ -0AA0 206
BUB 170 170 230 230 12 392 4.89 2LC0471-6AT ■ ■ -0AA0 200
487-6 55000 2150 NUN 225 225 305 305 298 13.0 215 41 376 – – 806 8.79 2LC0471-7NW ■ ■ -0AA0 294
BUN 180 225 250 305 194 23 100 624 8.38 2LC0471-7BD ■ ■ -0AA0 284
BUB 180 180 250 250 12 442 7.96 2LC0471-7AT ■ ■ -0AA0 274
522-6 69000 2000 NUN 240 240 325 325 324 13.0 230 44 400 – – 860 12.5 2LC0471-8NW ■ ■ -0AA0 361
BUN 200 240 275 325 206 23 107 666 12.0 2LC0471-8BD ■ ■ -0AA0 350
BUB 200 200 275 275 12 472 11.5 2LC0471-8AT ■ ■ -0AA0 339
572-6 92000 1800 NUN 265 265 360 360 356 15.0 255 47 446 – – 956 19.7 2LC0472-0NW ■ ■ -0AA0 477
BUN 220 265 300 360 229 24 114 739 18.7 2LC0472-0BD ■ ■ -0AA0 458
BUB 220 220 300 300 12 522 17.8 2LC0472-0AT ■ ■ -0AA0 439
602-6 106000 1700 NUN 280 280 380 380 368 16.0 270 50 470 – – 1010 26.9 2LC0472-1NW ■ ■ -0AA0 584
BUN 225 280 310 380 241 26 123 781 25.6 2LC0472-1BD ■ ■ -0AA0 562
BUB 225 225 310 310 12 552 24.3 2LC0472-1AT ■ ■ -0AA0 540
Up to size 240-6 available from stock. Ordering example:
ARPEX ARS-6 NUN coupling, size 140-6,
Because of the split variant, the coupling is optionally available Bore ∅D1 60H7 mm, with keyway to DIN 6885 and set screw,
with prefitted plate packs. Bore ∅D2 65K7 mm, with keyway to DIN 6885 and set screw.
For simplified fitting on B hubs, plate packs from size 280-6 Article No.:
available with closing element. 2LC0470-3NW99-0AA0-Z
Weights and mass moments of inertia apply to the entire L1E+M1F+M13
coupling with maximum bores D1/D2.
Siemens MD 10.1 · 2015 6/11

© Siemens AG 2015

Type NON

Torsionally rigid coupling with shortest possible shaft distance enabling problem-free fitting with commercially available tools.
Type NON with radially freely dismountable intermediate spacer. Type BON cannot be radially dismounted without moving the units.
LG
G_MD10_XX_00146
NL1 S NL2
S1 LG
A S
SZ
ØND2
ØND1
ØND1
ØND2
ØD2
ØDZ
ØDA
ØD1
ØD1
ØD2
6
P
B O N
N O N

Keyway NL2
DIN 6885
78-6 170 13400 NON 28 28 39 39 45 2.5 30 8 51 – – 111 0.001 2LC0470-0NV ■ ■ -0AA0 1.1
BON 28 8 29 88 2LC0470-0AS ■ ■ -0AA0
105-6 270 10000 NON 45 45 63 63 72 2.5 45 8 51 – – 141 0.003 2LC0470-1NV ■ ■ -0AA0 2.4
BON 13 8 29 103 2LC0470-1AS ■ ■ -0AA0
125-6 490 8400 NON 55 55 76 76 84 2.5 55 11 67 – – 177 0.008 2LC0470-2NV ■ ■ -0AA0 4.3
BON 21 10 37 131 2LC0470-2AS ■ ■ -0AA0
140-6 700 7500 NON 65 65 91 91 99 2.5 65 11 70 – – 200 0.015 2LC0470-3NV ■ ■ -0AA0 6.1
BON 14 10 37 144 2LC0470-3AS ■ ■ -0AA0
165-6 1250 6350 NON 75 75 105 105 114 2.5 75 14 83 – – 233 0.031 2LC0470-4NV ■ ■ -0AA0 9.4
BON 17 12 45 167 2LC0470-4AS ■ ■ -0AA0
175-6 2000 6000 NON 80 80 110 110 120 3.0 80 15 95 – – 255 0.047 2LC0470-5NV ■ ■ -0AA0 12.1
BON 27 15 52 187 2LC0470-5AS ■ ■ -0AA0
195-6 3000 5350 NON 90 90 120 120 131 3.0 80 15 95 – – 255 0.071 2LC0470-6NV ■ ■ -0AA0 14.5
BON 27 14 52 187 2LC0470-6AS ■ ■ -0AA0
210-6 4400 5000 NON 95 95 126 126 139 4.0 90 15 105 – – 285 0.105 2LC0470-7NV ■ ■ -0AA0 18.7
BON 28 20 61 208 2LC0470-7AS ■ ■ -0AA0
240-6 5700 4350 NON 110 110 145 145 162 5.0 100 18 116 – – 316 0.203 2LC0470-8NV ■ ■ -0AA0 27.3
BON 31 18 66 231 2LC0470-8AS ■ ■ -0AA0
255-6 7600 4100 NON 115 115 154 154 170 5.0 110 23 146 – – 366 0.309 2LC0471-0NV ■ ■ -0AA0 36.5
BON 54 24 81 274 2LC0471-0AS ■ ■ -0AA0
280-6 10000 3750 NON 135 135 184 184 186 6.0 130 25 150 – – 410 0.524 2LC0471-1NV ■ ■ -0AA0 52.3
BON 120 135 161 184 39 22 83 299 0.496 2LC0471-1AS ■ ■ -0AA0 49.9
6/12 Siemens MD 10.1 · 2015

© Siemens AG 2015

Type NON
Keyway NL2
DIN 6885
305-6 12000 3400 NON 145 145 198 198 200 6.5 140 27 174 – – 454 0.740 2LC0471-2NV ■ ■ -0AA0 64.1
BON 130 145 175 198 54 13 61 334 0.702 2LC0471-2AS ■ ■ -0AA0 61.3
335-6 18000 3100 NON 160 160 214 214 218 7.5 150 30 185 – – 485 1.14 2LC0471-3NV ■ ■ -0AA0 81.0
BON 140 160 190 214 57 15 69 357 1.09 2LC0471-3AS ■ ■ -0AA0 78.9
372-6 24000 2800 NON 165 165 225 225 228 9.5 160 32 209 – – 529 1.89 2LC0471-4NV ■ ■ -0AA0 112
BON 145 165 200 225 74 16 76 394 1.82 2LC0471-4AS ■ ■ -0AA0 109
407-6 34000 2550 NON 185 185 250 250 245 11.0 175 35 220 – – 570 2.98 2LC0471-5NV ■ ■ -0AA0 147
BON 145 185 205 250 72 19 83 422 2.84 2LC0471-5AS ■ ■ -0AA0 143
442-6 43000 2350 NON 200 200 270 270 273 11.0 190 38 241 – – 621 4.46 2LC0471-6NV ■ ■ -0AA0 185
BON 170 200 230 270 81 20 92 461 4.27 2LC0471-6AS ■ ■ -0AA0 179
487-6 55000 2150 NON 225 225 305 305 298 13.0 215 41 257 – – 687 7.51 2LC0471-7NV ■ ■ -0AA0 257
BON 180 225 250 305 75 23 100 505 7.10 2LC0471-7AS ■ ■ -0AA0 247
522-6 69000 2000 NON 240 240 325 325 324 13.0 230 44 278 – – 738 10.4 2LC0471-8NV ■ ■ -0AA0 311
BON 200 240 275 325 84 23 107 544 9.93 2LC0471-8AS ■ ■ -0AA0 300
572-6 92000 1800 NON 265 265 360 360 356 15.0 255 47 294 – – 804 16.5 2LC0472-0NV ■ ■ -0AA0 413
6
BON 220 265 300 360 77 24 114 587 15.6 2LC0472-0AS ■ ■ -0AA0 394
602-6 106000 1700 NON 280 280 380 380 368 16.0 270 50 315 – – 855 21.9 2LC0472-1NV ■ ■ -0AA0 492
BON 225 280 310 380 86 26 123 626 20.6 2LC0472-1AS ■ ■ -0AA0 470
Up to size 240-6 available from stock. Ordering example:
ARPEX ARS-6 NON coupling, size 105-6,
For simplified fitting on B hubs, plate packs from size 280-6 Bore ∅D1 40H7 mm, with keyway to DIN 6885 and set screw,
available with closing element. Bore ∅D2 45K7 mm, with keyway to DIN 6885 and set screw.
Weights and mass moments of inertia apply to the entire Article No.:
coupling with maximum bores D1/D2. 2LC0470-1NV99-0AA0-Z
L0W+M1A+M13
Siemens MD 10.1 · 2015 6/13

© Siemens AG 2015

Type NHN

Torsionally rigid coupling type NHN with variable shaft distance S. Type NHN with radially freely dismountable intermediate spacer.
LG
G_MD10_XX_00147a
NL1 S NL2
S1 LZ
SZ
ØND1
ØND2
ØDA
ØDZ
ØD1
ØD2
6
N H N
Size Rated Maximum Dimensions in mm Mass Article No. Weight

torque speed Shaft moment Order codes for bore
distance of diameters and tolerances
inertia are specified in catalog
DA TKN nKmax D1/D2 ND1/ND2 DZ SZ NL1/NL2 S1 LZ S J section 3 m
Keyway min. min.
DIN 6885
mm Nm rpm max. kgm2 kg
78-6 170 13400 28 39 44.5 3.2 30 8 69 85 0.002 2LC0470-0NT ■ ■ -0AZ0 4.3
105-6 270 10000 45 63 57.0 3.2 45 8 64 80 0.006 2LC0470-1NT ■ ■ -0AZ0 6.6
125-6 490 8400 55 76 63.5 4.0 55 11 73 95 0.014 2LC0470-2NT ■ ■ -0AZ0 10.2
140-6 700 7500 65 91 76.1 3.6 65 11 73 95 0.023 2LC0470-3NT ■ ■ -0AZ0 12.6
165-6 1250 6350 75 105 88.9 4.0 75 14 72 100 0.046 2LC0470-4NT ■ ■ -0AZ0 17.7
175-6 2000 6000 80 110 101.6 5.0 80 15 70 100 0.074 2LC0470-5NT ■ ■ -0AZ0 23.7
195-6 3000 5350 90 120 108.0 7.1 80 15 70 100 0.115 2LC0470-6NT ■ ■ -0AZ0 31.8
210-6 4400 5000 95 126 114.3 7.1 90 15 100 130 0.157 2LC0470-7NT ■ ■ -0AZ0 36.9
240-6 5700 4350 110 145 133.0 7.1 100 18 104 140 0.287 2LC0470-8NT ■ ■ -0AZ0 48.6
255-6 7600 4100 115 154 139.7 8.0 110 23 134 180 0.415 2LC0471-0NT ■ ■ -0AZ0 61.4
280-6 10000 3750 135 184 152.4 8.8 130 25 130 180 0.675 2LC0471-1NT ■ ■ -0AZ0 81.9
305-6 12000 3400 145 198 168.3 10.0 140 27 146 200 0.962 2LC0471-2NT ■ ■ -0AZ0 100
335-6 18000 3100 160 214 177.8 12.5 150 30 170 230 1.46 2LC0471-3NT ■ ■ -0AZ0 128
372-6 24000 2800 165 225 193.7 14.2 160 32 186 250 2.32 2LC0471-4NT ■ ■ -0AZ0 168
407-6 34000 2550 185 250 244.5 14.2 175 35 180 250 3.85 2LC0471-5NT ■ ■ -0AZ0 212
442-6 43000 2350 200 270 273.0 16.0 190 38 184 260 5.82 2LC0471-6NT ■ ■ -0AZ0 267
487-6 55000 2150 225 305 298.5 17.5 215 41 188 270 9.39 2LC0471-7NT ■ ■ -0AZ0 352
522-6 69000 2000 240 325 323.9 17.5 230 44 202 290 12.8 2LC0471-8NT ■ ■ -0AZ0 413
572-6 92000 1800 265 360 355.6 20.0 255 47 216 310 20.1 2LC0472-0NT ■ ■ -0AZ0 538
602-6 106000 1700 280 380 368.0 22.2 270 50 230 330 26.1 2LC0472-1NT ■ ■ -0AZ0 633
The permitted length of the intermediate spacer depends on the For greater shaft distances, see type NZN.
maximum operating speed of the coupling (see following table).
Weights and mass moments of inertia apply to the entire
In the case of individual order of the intermediate spacer, the coupling with maximum bores D1/D2 and S = 1000 mm.
length (LZ) must be specified.
6/14 Siemens MD 10.1 · 2015

© Siemens AG 2015

Type NHN
Permitted shaft distance S of type NHN relative to speed
Size Speed nN
rpm
DA 500 600 700 800 900 1000 1200 1400 1500 2000 2500 3000 4000
Permitted shaft distance S
mm mm
78-6 2809 2565 2376 2223 2096 1989 1816 1682 1625 1409 1261 1152 998
105-6 3203 2925 2709 2534 2390 2268 2071 1918 1853 1606 1437 1313 1138
125-6 3372 3079 2852 2668 2516 2388 2181 2020 1952 1692 1514 1383 1199
140-6 3719 3396 3145 2943 2775 2633 2405 2227 2152 1865 1669 1525 1322
165-6 4027 3677 3405 3186 3005 2852 2604 2412 2331 2020 1809 1652 1433
175-6 4296 3923 3633 3399 3206 3042 2778 2573 2487 2155 1929 1763 1529
195-6 4393 4011 3715 3476 3278 3110 2841 2631 2542 2204 1973 1802 1563
210-6 4527 4134 3828 3582 3378 3205 2927 2711 2620 2271 2033 1857 1610
240-6 4906 4480 4149 3882 3661 3474 3173 2939 2840 2462 2204 2013 1746
255-6 5023 4587 4249 3976 3750 3558 3250 3011 2910 2523 2259 2064 1791
280-6 5246 4791 4437 4152 3916 3717 3395 3145 3039 2635 2360 2156
305-6 5509 5031 4660 4361 4113 3903 3566 3303 3192 2768 2479 2265
335-6 5634 5146 4766 4461 4207 3993 3647 3379 3266 2832 2536 2318
372-6 5873 5364 4968 4650 4385 4162 3802 3523 3404 2952 2644
407-6 6647 6071 5623 5262 4963 4710 4303 3986 3852 3341 2992
442-6 7023 6414 5941 5560 5244 4977 4547 4212 4071 3530
6
487-6 7345 6708 6214 5815 5485 5205 4755 4406 4258 3693 Outside the permitted
522-6 7669 7005 6489 6072 5728 5436 4966 4601 4446 3857 speed range
572-6 8000 7333 6792 6356 5996 5690 5199 4817 4655
602-6 8000 7447 6898 6456 6089 5779 5280 4892 4728
Ordering example:
ARPEX ARS-6 NHN coupling, size 105-6, with shaft distance
S = 1000 mm,
Bore ∅D1 40H7 mm, with keyway to DIN 6885 and set screw,
Bore ∅D2 45K7 mm, with keyway to DIN 6885 and set screw.
Article No.:
2LC0470-1NT99-0AZ0-Z
L0W+M1A+Q0Y+M13
Plain text to Q0Y: S = 1000 mm
Siemens MD 10.1 · 2015 6/15

© Siemens AG 2015

Type NZN

Torsionally rigid coupling type NZN with variable shaft distance S and reinforced intermediate spacer.
Type NZN with radially freely dismountable intermediate spacer.
NL1 S NL2
G_MD10_XX_00148a
S1 LZ
SZ
ØDZ
ØND1
ØND2
ØDA
ØD1
ØD2
6
N Z N
Size Rated Maximum Dimensions in mm Mass Article No. Weight

DA TKN nKmax D1/D2 ND1/ND2 DZ SZ NL1/NL2 S1 LZ S J section 3 m
Keyway min. min.
DIN 6885
78-6 170 13400 28 39 76.1 3.6 30 8 400 416 0.009 2LC0470-0PC ■ ■ -0AZ0 7.8
105-6 270 10000 45 63 101.6 5.0 45 8 400 416 0.031 2LC0470-1PC ■ ■ -0AZ0 15.3
125-6 490 8400 55 76 114.3 7.1 55 11 400 422 0.061 2LC0470-2PC ■ ■ -0AZ0 23.9
140-6 700 7500 65 91 139.7 8.0 65 11 400 422 0.125 2LC0470-3PC ■ ■ -0AZ0 33.1
165-6 1250 6350 75 105 168.3 7.1 75 14 400 428 0.219 2LC0470-4PC ■ ■ -0AZ0 41.5
175-6 2000 6000 80 110 177.8 7.1 80 15 400 430 0.266 2LC0470-5PC ■ ■ -0AZ0 45.6
195-6 3000 5350 90 120 193.7 7.1 80 15 400 430 0.361 2LC0470-6PC ■ ■ -0AZ0 51.7
210-6 4400 5000 95 126 193.7 7.1 90 15 400 430 0.392 2LC0470-7PC ■ ■ -0AZ0 55.0
240-6 5700 4350 110 145 219.1 7.1 100 18 400 436 0.622 2LC0470-8PC ■ ■ -0AZ0 68.3
255-6 7600 4100 115 154 244.5 7.1 110 23 400 446 0.902 2LC0471-0PC ■ ■ -0AZ0 85.9
280-6 10000 3750 135 184 273.0 7.1 130 25 400 450 1.39 2LC0471-1PC ■ ■ -0AZ0 112
305-6 12000 3400 145 198 298.5 11.0 140 27 400 454 2.28 2LC0471-2PC ■ ■ -0AZ0 155
335-6 18000 3100 160 214 323.9 11.0 150 30 400 460 3.13 2LC0471-3PC ■ ■ -0AZ0 180
The permitted length of the intermediate spacer depends on the Weights and mass moments of inertia apply to the entire
maximum operating speed of the coupling (see following table). coupling with maximum bores D1/D2 and S = 1000 mm.
In the case of individual order of the intermediate spacer, the
6/16 Siemens MD 10.1 · 2015

© Siemens AG 2015

Type NZN
Permitted shaft distance S of type NZN relative to speed
Size Speed nN
rpm
DA 500 600 700 800 900 1000 1200 1400 1500 2000 2500 3000 4000
mm mm
78-6 3716 3393 3142 2940 2772 2630 2402 2224 2149 1862 1666 1522 1319
105-6 4289 3916 3626 3392 3199 3035 2771 2566 2480 2148 1922 1756 1522
125-6 4523 4130 3824 3578 3374 3201 2923 2707 2616 2267 2029 1853 1606
140-6 5011 4575 4237 3964 3738 3546 3238 2999 2898 2511 2247 2052 1779
165-6 5543 5061 4687 4385 4135 3924 3583 3318 3206 2779 2487 2271 1969
175-6 5704 5209 4823 4513 4256 4038 3687 3415 3300 2860 2559 2338 2026
195-6 5963 5445 5042 4717 4448 4221 3854 3570 3449 2989 2675 2443 2118
210-6 5963 5445 5042 4717 4448 4221 3854 3570 3449 2989 2675 2443 2118
240-6 6357 5805 5376 5030 4743 4501 4110 3807 3678 3188 2853 2606 2259
255-6 6731 6147 5692 5326 5023 4766 4353 4032 3896 3377 3023 2762 2395
280-6 7124 6505 6025 5637 5316 5045 4607 4267 4124 3574 3200 2923 –
305-6 7410 6767 6267 5864 5530 5248 4793 4439 4290 3719 3329 3041 –
335-6 7732 7061 6539 6119 5771 5476 5002 4633 4477 3881 3474 3174 –
Ordering example:
ARPEX ARS-6 NZN coupling, size 105-6, with shaft distance
S = 1000 mm,
6
Article No.:
2LC0470-1PC99-0AZ0-Z
L0W+M1A+Q0Y+M13
Siemens MD 10.1 · 2015 6/17

© Siemens AG 2015

Type NWN

Torsionally rigid coupling type NWN with radially freely dismountable intermediate, torsion or flange shaft and variable shaft distance S.
NL1 S NL2
G_MD10_EN_00149a
S1
LW
Variant ZW with intermediate shaft

ØND1
ØND2
ØDA
ØD1
ØD2
N W N
NL1 S NL2
NL1 S NL2 S1
S1
6
LW
LW
ØND1
ØND2
ØND1
ØND2
ØDA
ØDA
ØD1
ØD2
ØD1
ØD2
N W N N W N
Variant TW with torsion shaft Variant FW with flanged shaft
Size Rated Maximum Type Dimensions in mm Mass Article No. Weight

DA TKN nKmax D1/D2 ND1 NL1/NL2 S1 LW S J section 3 m
Keyway min. min.
DIN 6885
78-6 170 13400 ZW 28 39 30 8 74 90 0.001 2LC0470-0NX ■ ■ -0AZ0 1.7
TW 74 90 2LC0470-0PB ■ ■ -0AZ0
FW 35 51 2LC0470-0PA ■ ■ -0AZ0
105-6 270 10000 ZW 45 63 45 8 104 120 0.004 2LC0470-1NX ■ ■ -0AZ0 4.6
TW 104 120 2LC0470-1PB ■ ■ -0AZ0
FW 35 51 2LC0470-1PA ■ ■ -0AZ0
125-6 490 8400 ZW 55 76 55 11 123 145 0.011 2LC0470-2NX ■ ■ -0AZ0 8.3
TW 123 145 2LC0470-2PB ■ ■ -0AZ0
FW 45 67 2LC0470-2PA ■ ■ -0AZ0
140-6 700 7500 ZW 65 91 65 11 143 165 0.021 2LC0470-3NX ■ ■ -0AZ0 12.8
TW 143 165 2LC0470-3PB ■ ■ -0AZ0
FW 48 70 2LC0470-3PA ■ ■ -0AZ0
165-6 1250 6350 ZW 75 105 75 14 162 190 0.045 2LC0470-4NX ■ ■ -0AZ0 19.6
TW 162 190 2LC0470-4PB ■ ■ -0AZ0
FW 55 83 2LC0470-4PA ■ ■ -0AZ0
175-6 2000 6000 ZW 80 110 80 15 170 200 0.064 2LC0470-5NX ■ ■ -0AZ0 24.0
TW 170 200 2LC0470-5PB ■ ■ -0AZ0
FW 65 95 2LC0470-5PA ■ ■ -0AZ0
195-6 3000 5350 ZW 90 120 80 15 170 200 0.096 2LC0470-6NX ■ ■ -0AZ0 28.7
TW 170 200 2LC0470-6PB ■ ■ -0AZ0
FW 65 95 2LC0470-6PA ■ ■ -0AZ0
210-6 4400 5000 ZW 95 126 90 15 190 220 0.138 2LC0470-7NX ■ ■ -0AZ0 36.1
TW 190 220 2LC0470-7PB ■ ■ -0AZ0
FW 75 105 2LC0470-7PA ■ ■ -0AZ0
6/18 Siemens MD 10.1 · 2015

© Siemens AG 2015

Type NWN
DA TKN nKmax D1/D2 ND1 NL1/NL2 S1 LW S J section 3 m
Keyway min. min.
DIN 6885
240-6 5700 4350 ZW 110 145 100 18 214 250 0.267 2LC0470-8NX ■ ■ -0AZ0 53.1
TW 214 250 2LC0470-8PB ■ ■ -0AZ0
FW 80 116 2LC0470-8PA ■ ■ -0AZ0
255-6 7600 4100 ZW 115 154 110 23 234 280 0.398 2LC0471-0NX ■ ■ -0AZ0 68.3
TW 234 280 2LC0471-0PB ■ ■ -0AZ0
FW 100 146 2LC0471-0PA ■ ■ -0AZ0
280-6 10000 3750 ZW 135 184 130 25 270 320 0.734 2LC0471-1NX ■ ■ -0AZ0 105
TW 270 320 2LC0471-1PB ■ ■ -0AZ0
FW 100 150 2LC0471-1PA ■ ■ -0AZ0
305-6 12000 3400 ZW 145 198 140 27 296 350 1.04 2LC0471-2NX ■ ■ -0AZ0 129
TW 296 350 2LC0471-2PB ■ ■ -0AZ0
FW 120 174 2LC0471-2PA ■ ■ -0AZ0
335-6 18000 3100 ZW 160 214 150 30 310 370 1.58 2LC0471-3NX ■ ■ -0AZ0 162
TW 310 370 2LC0471-3PB ■ ■ -0AZ0
FW 125 185 2LC0471-3PA ■ ■ -0AZ0
6
372-6 24000 2800 ZW 165 225 160 32 336 400 2.44 2LC0471-4NX ■ ■ -0AZ0 206
TW 336 400 2LC0471-4PB ■ ■ -0AZ0
FW 145 209 2LC0471-4PA ■ ■ -0AZ0
407-6 34000 2550 ZW 185 250 175 35 360 430 3.89 2LC0471-5NX ■ ■ -0AZ0 272
TW 360 430 2LC0471-5PB ■ ■ -0AZ0
FW 150 220 2LC0471-5PA ■ ■ -0AZ0
442-6 43000 2350 ZW 200 270 190 38 394 470 5.83 2LC0471-6NX ■ ■ -0AZ0 347
TW 394 470 2LC0471-6PB ■ ■ -0AZ0
FW 165 241 2LC0471-6PA ■ ■ -0AZ0
487-6 55000 2150 ZW 225 305 215 41 448 530 10.0 2LC0471-7NX ■ ■ -0AZ0 489
TW 448 530 2LC0471-7PB ■ ■ -0AZ0
FW 175 257 2LC0471-7PA ■ ■ -0AZ0
522-6 69000 2000 ZW 240 325 230 44 472 560 13.9 2LC0471-8NX ■ ■ -0AZ0 593
TW 472 560 2LC0471-8PB ■ ■ -0AZ0
FW 190 278 2LC0471-8PA ■ ■ -0AZ0
572-6 92000 1800 ZW 265 360 255 47 526 620 22.4 2LC0472-0NX ■ ■ -0AZ0 797
TW 526 620 2LC0472-0PB ■ ■ -0AZ0
FW 200 294 2LC0472-0PA ■ ■ -0AZ0
602-6 106000 1700 ZW 280 380 270 50 550 650 29.5 2LC0472-1NX ■ ■ -0AZ0 941
TW 550 650 2LC0472-1PB ■ ■ -0AZ0
FW 215 315 2LC0472-1PA ■ ■ -0AZ0
The permitted length of the intermediate spacer depends on the Ordering example:
maximum operating speed of the coupling. ARPEX ARS-6 NWN coupling, size 105-6, with intermediate shaft
and shaft distance S = 1000 mm,
Weights and mass moments of inertia apply to four hubs with Bore ∅D1 40H7 mm, with keyway to DIN 6885 and set screw,
maximum bore D1/D2 and two plate packs. Bore ∅D2 45K7 mm, with keyway to DIN 6885 and set screw.
Article No.:
2LC0470-1NX99-0AZ0-Z
L0W+M1A+Q0Y+M13
Siemens MD 10.1 · 2015 6/19

© Siemens AG 2015

Further hubs and flanges
J hub

J hubs or jumbo hubs are used where the shaft diameter is greater than the maximum bore diameter of the N hub. Because of the
larger hub core diameter "ØND1", the J hub cannot be used as a B hub, i.e. the hub core diameter is greater than the inside diameter
of the spacer tube and cannot project into the spacer. The J hub can be combined with any spacer.
NL
U1
ØND1
ØD1
ØDA
6
G_MD10_XX_00150
6/20 Siemens MD 10.1 · 2015

© Siemens AG 2015

J hub
Size Dimensions in mm Mass moment of Article No. Weight

inertia
DA D1 ND1 NL U1 J Order codes for bore m
Keyway DIN 6885 diameters and toler-
ances are specified in
max. catalog section 3
mm kgm2 kg
78-6 40 53 30 7 0.0002 2LC0470-0JU90-0AA0 0.3
105-6 60 80 45 7 0.0013 2LC0470-1JU90-0AA0 0.9
125-6 70 92 55 9 0.0029 2LC0470-2JU90-0AA0 1.5
140-6 80 107 65 9 0.0058 2LC0470-3JU90-0AA0 2.4
165-6 92 124 75 9 0.0121 2LC0470-4JU90-0AA0 3.7
175-6 96 130 80 12 0.0168 2LC0470-5JU90-0AA0 4.5
195-6 106 142 80 12 0.0244 2LC0470-6JU90-0AA0 5.4
210-6 110 149 90 13 0.0347 2LC0470-7JU90-0AA0 6.9
240-6 130 173 100 15 0.0675 2LC0470-8JU90-0AA0 9.9
255-6 135 182 110 18 0.0961 2LC0471-0JU90-0AA0 12.6
Weights and mass moments of inertia apply to a J hub with a Ordering example:
maximum bore D1. ARPEX ARS-6 J hub, size 105-6,
hub with bore 60H7 mm and parallel keyway to DIN 6885/1 and
set screw.
Article No.:
2LC0470-1JU90-0AA0
6
L1E
Siemens MD 10.1 · 2015 6/21

© Siemens AG 2015

F flange, D flange, C flange

F, D and C flanges are used where torque is to be transmitted by flange connections.
F, D and C flanges can be combined with any spacer.
F flange D flange C flange
S S
S
U1
SZ
U1
ØDFN
ØDFR
ØDFR
ØDFN
ØDFK
ØDFA
ØDFK
ØDFA
ØDFK
ØDA
ØDA
ØDZ
G_MD10_EN_00151a
ZF x M
6
ZF x ØDFB
ZF x ØDFB
BF
TF U1 TF
BF BF
U3 U4
Size Type Dimensions in mm Mass moment Article No. Weight

of inertia
DA DFR DFA DFN DZ SZ DFK DFB M ZF BF U1 U3 U4 TF J m
mm kgm2 kg
78-6 F 90j6 125 40 – – 110 6.6 – 6 7 7 10 – 2 0.0014 2LC0470-0GP00-0AA0 0.7
D – 45 2.5 – 35 0.0014 2LC0470-0EC00-0AA0 0.8
C – – 40H7 – – 66 – 6 6 12 – – 0.0002 2LC0470-0BE00-0AA0 0.2
105-6 F 120j6 155 60 – – 140 6.6 – 6 7 7 10 – 2 0.0036 2LC0470-1GP00-0AA0 1.1
D – 72 2.5 – 35 0.0036 2LC0470-1EC00-0AA0 1.2
C – – 60H7 – – 93 – 6 6 12 – – 0.0007 2LC0470-1BE00-0AA0 0.4
125-6 F 140j6 178 75 – – 160 9.0 – 6 9 9 13 – 2 0.0077 2LC0470-2GP00-0AA0 1.8
D – 84 2.5 – 45 0.0079 2LC0470-2EC00-0AA0 1.9
C – – 75H7 – – 109 – 8 6 15 – – 0.0016 2LC0470-2BE00-0AA0 0.7
140-6 F 155j6 194 90 – – 175 9.0 – 6 9 9 13 – 2 0.0109 2LC0470-3GP00-0AA0 2.0
D – 99 2.5 – 45 0.0113 2LC0470-3EC00-0AA0 2.2
C – – 90H7 – – 124 – 8 6 15 – – 0.0026 2LC0470-3BE00-0AA0 0.8
165-6 F 180j6 232 95 – – 210 11.0 – 6 9 9 15 – 2 0.0233 2LC0470-4GP00-0AA0 3.3
D – 114 2.5 – 55 0.0226 2LC0470-4EC00-0AA0 3.2
C – – 95H7 – – 145 – 10 6 17 – – 0.0060 2LC0470-4BE00-0AA0 1.4
175-6 F 190j6 245 105 – – 220 14.0 – 6 12 12 19 – 2 0.0365 2LC0470-5GP00-0AA0 4.5
D – 120 3.0 – 65 0.0368 2LC0470-5EC00-0AA0 4.7
C – – 105H7 – – 153 – 12 6 21 – – 0.0091 2LC0470-5BE00-0AA0 1.8
195-6 F 215j6 270 115 – – 245 14.0 – 8 12 12 20 – 2 0.0559 2LC0470-6GP00-0AA0 5.6
D – 131 3.0 – 65 0.0542 2LC0470-6EC00-0AA0 5.6
C – – 115H7 – – 169 – 14 6 22 – – 0.0146 2LC0470-6BE00-0AA0 2.4
210-6 F 230j6 300 120 – – 270 18.0 – 6 13 13 22 – 2 0.0907 2LC0470-7GP00-0AA0 7.6
D – 139 4.0 – 75 0.0889 2LC0470-7EC00-0AA0 7.7
C – – 120H7 – – 180 – 16 6 24 – – 0.0210 2LC0470-7BE00-0AA0 3.1
240-6 F 260j6 330 140 – – 300 18.0 – 8 15 15 26 – 2 0.1549 2LC0470-8GP00-0AA0 10.6
D – 162 5.0 – 80 0.1514 2LC0470-8EC00-0AA0 10.7
C – – 140H7 – – 207 – 18 6 28 – – 0.0416 2LC0470-8BE00-0AA0 4.6
6/22 Siemens MD 10.1 · 2015

© Siemens AG 2015

F flange, D flange, C flange
Size Type Dimensions in mm Mass moment Article No. Weight
of inertia
DA DFR DFA DFN DZ SZ DFK DFB M ZF BF U1 U3 U4 TF J m
mm kgm2 kg
255-6 F 275m6 345 150 – – 315 18.0 – 8 18 18 30 – 2 0.2167 2LC0471-0GP00-0AA0 13.2
D – 170 5.0 – 100 0.2168 2LC0471-0EC00-0AA0 13.9
C – – 150H7 – – 219 – 20 6 32 – – 0.0586 2LC0471-0BE00-0AA0 5.7
280-6 F 305m6 375 160 – – 345 18.0 – 10 19 19 31 – 3 0.3278 2LC0471-1GP00-0AA0 17.1
D – 186 6.0 – 100 0.3266 2LC0471-1EC00-0AA0 17.9
C – – 160H7 – – 240 – 22 6 34 – – 0.0927 2LC0471-1BE00-0AA0 7.6
305-6 F 330m6 400 180 – – 370 18.0 – 12 20 20 37 – 3 0.4709 2LC0471-2GP00-0AA0 21.3
D – 200 6.5 – 120 0.4519 2LC0471-2EC00-0AA0 21.9
C – – 180H7 – – 260 – 24 6 40 – – 0.1442 2LC0471-2BE00-0AA0 9.8
335-6 F 365m6 447 190 – – 410 22.0 – 10 22 22 41 – 3 0.8051 2LC0471-3GP00-0AA0 29.9
D – 218 7.5 – 125 0.7586 2LC0471-3EC00-0AA0 29.7
C – – 190H7 – – 285 – 27 6 44 – – 0.2334 2LC0471-3BE00-0AA0 13.5
372-6 F 410m6 505 200 – – 460 22.0 – 12 25 25 46 – 3 1.4635 2LC0471-4GP00-0AA0 42.9
D – 228 9.5 – 145 1.3843 2LC0471-4EC00-0AA0 44.0
C – – 200H7 – – 310 – 30 6 49 – – 0.3947 2LC0471-4BE00-0AA0 19.0
407-6 F 445m6 535 210 – – 490 22.0 – 16 27 27 48 – 3 1.9809 2LC0471-5GP00-0AA0 51.9
D – 245 11.0 – 150 1.9083 2LC0471-5EC00-0AA0 54.4
C – – 210H7 – – 340 – 33 6 51 – – 0.6095 2LC0471-5BE00-0AA0 25.2
6
442-6 F 490m6 585 230 – – 540 22.0 – 18 30 30 55 – 3 3.2065 2LC0471-6GP00-0AA0 70.0
D – 273 11.0 – 165 2.9664 2LC0471-6EC00-0AA0 69.0
C – – 230H7 – – 370 – 36 6 58 – – 0.9466 2LC0471-6BE00-0AA0 33.0
487-6 F 535m6 645 260 – – 590 26.0 – 16 33 33 60 – 3 5.1248 2LC0471-7GP00-0AA0 91.6
D – 298 13.0 – 175 4.8658 2LC0471-7EC00-0AA0 94.3
C – – 260H7 – – 410 – 39 6 63 – – 1.5350 2LC0471-7BE00-0AA0 43.4
522-6 F 580m6 695 280 – – 640 26.0 – 18 36 36 63 – 4 7.4857 2LC0471-8GP00-0AA0 114
D – 324 13.0 – 190 7.0887 2LC0471-8EC00-0AA0 117
C – – 280H7 – – 440 – 42 6 67 – – 2.0955 2LC0471-8BE00-0AA0 51.4
572-6 F 625m6 770 310 – – 700 33.0 – 16 38 38 67 – 4 11.6519 2LC0472-0GP00-0AA0 147
D – 356 15.0 – 200 11.2872 2LC0472-0EC00-0AA0 153
C – – 310H7 – – 480 – 45 6 71 – – 3.2918 2LC0472-0BE00-0AA0 66.6
602-6 F 655m6 800 320 – – 730 33.0 – 16 41 41 72 – 4 14.7118 2LC0472-1GP00-0AA0 172
D – 368 16.0 – 215 14.3454 2LC0472-1EC00-0AA0 181
C – – 320H7 – – 505 – 48 6 76 – – 4.3874 2LC0472-1BE00-0AA0 81.1
F, D and C flanges are readily available in many sizes.
Ordering example:
ARPEX ARS-6 F flange, size 105-6.
Article No.:
2LC0470-1GP00-0AA0
Siemens MD 10.1 · 2015 6/23

© Siemens AG 2015

Clamping hub

Standard clamping hub types 124 and 125 can be combined Transmissible torque
with any spacer. It should be noted that the clamping hub can
be used only as an "N hub" (hub core outside). Clamping hub as The clamping connections are designed to enable the specified
"B hub" (hub core in spacer tube) on request. Transmissible maximum torques to be transmitted. These maximum torques
torque and maximum bore diameter are smaller on a B hub vari- may not be exceeded. The mathematical coefficient of friction
ant than stated below. between the shaft and the clamping hub is μ = 0.16.
Function Fitting clearance and surface roughness
ARPEX clamping hubs transmit torque with the aid of a flexible The transmissible torques take into account the maximum fitting
press fit. By pulling the clamping ring on by means of the tight- clearance and maximum surface roughness. For other shaft tol-
ening screws the necessary surface pressure is applied in the erances reduced torques or other bore tolerances must be used.
"shaft/hub" contact area. After the tightening operation the The surface roughness of the shaft should be ≤ Ra = 1.6 μm.
clamping ring lies up against the clamping hub. The gap dimen- The shaft tolerance must be specified in the order.
sion between the clamping hub and the clamping ring is then To specify, "-Z" must be added to the article number and the
zero. This has the effect that even with repeated fitting and dis- order code "Y26" with plain text specification of the shaft
mounting the balancing condition is maintained (no wobble ef- tolerance for D1 must be added as well. The fit pairing G6/h6
fect). Clamping hubs can be clamped as often as required. It should be used wherever possible.
must be ensured that the taper surfaces are adequately lubri-
cated.
Type 124 Type 125

6
NL NL
L2 L2
ØND1
ØND1
ØDA
ØDA
ØD1
ØD1
G_MD10_EN_00152
A
Size Clamping Dimensions in mm Mass moment Article No. Weight

hub of inertia Order codes for bore
DA Type D1 D1 ND1 NL L2 A J diameters and toler- m
2
catalog section 3
mm min. max. kgm kg
78-6 124 15 25 48 35 19 6 0.0002 2LC0470-0LM90-0AA0 0.5
125 2LC0470-0LN90-0AA0
105-6 124 25 45 74 40 22 8 0.0012 2LC0470-1LM90-0AA0 1.0
125 2LC0470-1LN90-0AA0
125-6 124 30 50 86 45 28 8 0.0026 2LC0470-2LM90-0AA0 1.6
125 2LC0470-2LN90-0AA0
140-6 124 30 60 103 50 33 9 0.0051 2LC0470-3LM90-0AA0 2.4
125 2LC0470-3LN90-0AA0
165-6 124 38 70 118 55 33 9 0.0096 2LC0470-4LM90-0AA0 3.4
125 2LC0470-4LN90-0AA0
175-6 124 42 75 122 65 43 10 0.0141 2LC0470-5LM90-0AA0 4.3
125 2LC0470-5LN90-0AA0
195-6 124 48 75 135 70 44 9 0.0231 2LC0470-6LM90-0AA0 6.2
125 2LC0470-6LN90-0AA0
210-6 124 55 85 141 75 49 9 0.0309 2LC0470-7LM90-0AA0 7.2
125 2LC0470-7LN90-0AA0
240-6 124 65 95 164 90 59 10 0.0648 2LC0470-8LM90-0AA0 11.4
125 2LC0470-8LN90-0AA0
6/24 Siemens MD 10.1 · 2015

© Siemens AG 2015

Clamping hub
Size Clamping Dimensions in mm Mass moment Article No. Weight
hub of inertia Order codes for bore
DA Type D1 D1 ND1 NL L2 A J diameters and toler- m
catalog section 3
mm min. max. kgm2 kg
255-6 124 70 95 171 95 64 10 0.0886 2LC0471-0LM90-0AA0 14.1
125 2LC0471-0LN90-0AA0
280-6 124 75 110 189 115 79 – 0.1489 2LC0471-1LM90-0AA0 19.6
125 2LC0471-1LN90-0AA0
305-6 124 80 120 203 125 90 – 0.2163 2LC0471-2LM90-0AA0 24.3
125 2LC0471-2LN90-0AA0
335-6 124 85 130 221 140 100 – 0.3441 2LC0471-3LM90-0AA0 32.6
125 2LC0471-3LN90-0AA0
372-6 124 95 140 230 150 110 – 0.4955 2LC0471-4LM90-0AA0 38.8
125 2LC0471-4LN90-0AA0
Additional coupling sizes are available on request. Forcing-off threads of clamping hubs of type 124 from size 280
fitted from flange side (like type 125).
Smaller bore diameters D1 min. are available on request.
Weights and mass moments of inertia apply to a clamping hub
with a maximum bore D1.
Dimensions and torques
Finished Size
6
bore/shaft in 78-6 105-6 125-6 140-6 165-6 175-6 195-6 210-6 240-6 255-6 280-6 305-6 335-6 372-6
standard fit
Rated coupling torque TKN
Nm
170 270 490 700 1250 2000 3000 4400 5700 7600 10000 12000 18000 24000
D1G6/h6 Maximum transmissible torque of the clamping hub
mm Nm
16 200 – – – – – – – – – – – – –
19 220 – – – – – – – – – – – – –
20 250 – – – – – – – – – – – – –
22 245 – – – – – – – – – – – – –
24 195 – – – – – – – – – – – – –
25 225 270 – – – – – – – – – – – –
28 – 400 – – – – – – – – – – – –
30 – 380 670 900 – – – – – – – – – –
32 – 430 710 940 – – – – – – – – – –
35 – 390 740 1060 – – – – – – – – – –
38 – 520 950 1340 1720 – – – – – – – – –
40 – 400 810 1140 1970 – – – – – – – – –
42 – 480 950 1320 1790 2590 – – – – – – – –
45 – 505 850 1190 2150 3120 – – – – – – – –
48 – – 850 1400 2430 3200 3280 – – – – – – –
50 – – 970 1090 2500 3550 3650 – – – – – – –
55 – – – 1390 2300 3870 3750 4120 – – – – – –
60 – – – 1180 2020 3490 4490 5220 – – – – – –
65 – – – – 2500 4000 4840 6630 7600 – – – – –
70 – – – – 2360 3610 5110 7430 9200 9800 – – – –
75 – – – – – 3070 5040 7430 9600 11700 14600 – – –
80 – – – – – – – 7330 8800 12600 17200 19300 – –
85 – – – – – – – 6260 10000 12400 18300 21400 25100 –
90 – – – – – – – – 9700 14200 20000 23600 29000 –
95 – – – – – – – – 10000 14700 19700 24000 30400 36300
100 – – – – – – – – – – 19700 24000 34400 41100
110 – – – – – – – – – – 19100 24000 33600 44200
120 – – – – – – – – – – – 24000 33400 48000
130 – – – – – – – – – – – – 33500 46700
140 – – – – – – – – – – – – – 44900
The maximum transmissible torque of the clamping hub must not Ordering example:
be exceeded! ARPEX ARS-6 clamping hub, size 105-6, type 124,
for shaft diameter 40h6 mm.
Further coupling sizes and higher torques are available on
request. Article No.:
2LC0470-1LM90-0AA0-Z
L0W+Y26
clear text to Y26: h6
Siemens MD 10.1 · 2015 6/25

© Siemens AG 2015

Spare and wear parts
Plate pack ARS-6
S1
S1
Figure 1 Figure 2
ØDA
ØDA
6
G_MD10_EN_00153
Plate packs up to size 255-6 comprise ring plates (Fig. 1) and from size 280-6 side-bar plates (Fig. 2).
Dimensions in mm Mass moment of inertia Article No. Weight
Size
DA S1 J m
kgm2 kg
78-6 8 0.0001 2LC0470-0NQ00-0AA0 0.1
105-6 8 0.0003 2LC0470-1NQ00-0AA0 0.1
125-6 11 0.0009 2LC0470-2NQ00-0AA0 0.3
140-6 11 0.0012 2LC0470-3NQ00-0AA0 0.3
165-6 14 0.0033 2LC0470-4NQ00-0AA0 0.7
175-6 15 0.0050 2LC0470-5NQ00-0AA0 0.9
195-6 15 0.0084 2LC0470-6NQ00-0AA0 1.2
210-6 15 0.0137 2LC0470-7NQ00-0AA0 1.8
240-6 18 0.0253 2LC0470-8NQ00-0AA0 2.5
255-6 23 0.0410 2LC0471-0NQ00-0AA0 3.5
280-6 25 0.0613 2LC0471-1NQ00-0AA0 4.4
305-6 27 0.0734 2LC0471-2NQ00-0AA0 4.6
335-6 30 0.1180 2LC0471-3NQ00-0AA0 6.1
372-6 32 0.2127 2LC0471-4NQ00-0AA0 9.3
407-6 35 0.3387 2LC0471-5NQ00-0AA0 12.3
442-6 38 0.4950 2LC0471-6NQ00-0AA0 15.2
487-6 41 0.7965 2LC0471-7NQ00-0AA0 20.0
522-6 44 1.0849 2LC0471-8NQ00-0AA0 23.6
572-6 47 1.6931 2LC0472-0NQ00-0AA0 31.0
602-6 50 2.2420 2LC0472-1NQ00-0AA0 37.1
The plate pack of the ARS-6 series is readily available as a Ordering example:
spare part. ARPEX ARS-6 plate pack, size 105-6,
complete with screw connections.
The plate pack is delivered with screw connection.
Up to size 280-6 close-fitting bolts with collar nuts are used. Article No.:
From size 305-6 patented 1) conical screw connections are 2LC0470-1NQ00-0AA0
used.
1)
this catalog.
6/26 Siemens MD 10.1 · 2015

© Siemens AG 2015

Torsionally Rigid All-Steel Couplings — ARPEX ARC-8/-10 Series
General information
■ Overview
Coupling can be designed for use in potentially explosive

atmospheres in accordance with the current ATEX Directive.
■ Benefits
6
ARPEX couplings of the ARC-8/-10 series are outstanding for positive fit and is designed to be extremely easy to fit. Couplings
their robust construction. They have been optimized for high can be designed for use in potentially explosive atmospheres in
torques combined with high speeds. The patented 1) conical accordance with the current ATEX Directive.
screw connection ensures reliable torque transmission by a true
■ Application
ARPEX couplings of the ARC-8 and ARC-10 series are output-
and speed-optimized coupling solutions. Power transmission is
by means of patented 1) conical screw connections and plate
packs of the octagonal and decagonal types. Torques of be-
tween 8.5 and 1450 kNm can be transmitted at a permitted an-
gular misalignment of 0.2° to 0.4°. The closed flange shape and
a compact construction permit high peripheral speeds and high
speeds. On most types, the intermediate spacer can be radially
fitted without moving the connected units.
Main areas of application for the ARC-8/-10 series:
• Paper-making machines
• Printing machines
• Compressors
• Fans and blowers
• Generators
• Presses
• Conveyors
• Crane systems
• Pumps
• Mills
• Rotary furnaces
• Stirrers
1)
this catalog.
Siemens MD 10.1 · 2015 6/27

© Siemens AG 2015

General information
■ Design
The classic design of an ARPEX coupling of the ARC-8/-10 se- Conical screw connections are used for fastening. The interme-
ries type NEN is shown in the following illustration. The plate diate spacer lengths are variably designed according to cus-
packs are bolted alternately between the flanges of the coupling tomer specifications.
hubs and the intermediate spacer.
Hub
Plate pack
Intermediate spacer
Hub
Tightening screw
6
Washer
Taper sleeve
Taper bolt
Screw plug G_MD10_EN_00154a
Design of an ARPEX coupling, ARC-8/-10 series, type NEN

Variants of the ARPEX coupling, ARC-8/-10 series
Types
The coupling parts of the ARPEX ARC-8/-10 series with the
exception of the H spacers have been machined on all sides.
NEN Variant with intermediate spacer machined on all sides,
length variable These are delivered with unmachined and primed spacer tube.
NHN Variant with unmachined intermediate spacer, Further application-specific coupling types are available in
length variable selection module X.CAT NG at www.siemens.com/couplings.
BUB Compact variant with split intermediate spacer for Dimension sheets and further information are available on re-
short shaft distances
quest.
MFEFM Variant with preassembled intermediate unit and
machined intermediate spacer, length variable
MFHFM Variant with preassembled intermediate unit and
unmachined intermediate spacer, length variable
6/28 Siemens MD 10.1 · 2015

© Siemens AG 2015

General information
■ Technical data
Power ratings
torque mum load torque mum ±ΔKa ±ΔKw ±ΔKr CT
torque torque speed
TKN TKmax TKOL TKW nKmax NEN BUB MFEFM NEN NHN BUB MFEFM MFHFM
NHN MFHFM for for
S= S= S S= S S=
1000 mm 1000 mm min. 1000 mm min. 1000 mm
kNm kNm kNm kNm rpm mm mm mm mm MNm/rad MNm/rad MNm/rad MNm/rad MNm/rad
225-8 8.5 17 25.5 4.25 8500 1.94 0.4° 6.87 0.96 6.53 3.1 0.9368 3.0 3.1 0.9748
255-8 12.7 25.4 38.1 6.35 7500 2.32 6.86 1.10 6.51 3.8 1.2778 3.7 3.8 1.3295
270-8 16.5 33 49.5 8.25 7000 2.40 6.88 1.10 6.52 5.4 1.7339 5.1 5.4 1.8072
295-8 23 46 69 11.5 6500 2.62 6.86 1.17 6.44 7.1 2.6134 6.7 7.1 2.7358
325-8 33 66 99 16.5 6000 2.60 6.84 1.38 6.34 9.6 3.9537 9.4 9.6 4.1715
355-8 45 90 135 22.5 5500 2.88 6.83 1.42 6.28 12.8 5.6093 12.5 12.8 5.9339
385-8 56 112 168 28 5000 3.12 6.81 1.63 6.22 17.8 7.8517 17.0 17.8 8.3555
420-8 70 140 210 35 4500 3.46 6.79 1.78 6.14 22.9 10.8175 21.9 22.9 11.5763
455-8 88 176 264 44 4200 4.02 6.78 1.89 6.11 30.0 14.2794 28.2 30.0 15.2998
505-8 120 240 360 60 3800 4.28 6.77 2.41 6.04 40.2 20.9046 36.4 40.2 22.4421
545-8 165 330 495 82.5 3500 4.48 6.75 2.67 5.98 50.4 28.7428 45.0 50.4 30.7848
595-8 210 420 630 105 3200 4.86 6.73 2.88 5.89 67.8 39.5343 59.5 67.8 42.5997
6
630-8 260 520 780 130 3000 4.98 0.3° 4.93 2.10 4.14 61.8 42.6162 61.2 61.8 46.3697
700-8 340 680 1020 170 2700 5.78 4.91 2.38 4.06 84.9 60.2135 83.1 84.9 65.8083
S= S= S= S=
1500 mm 1500 mm 1500 mm 1500 mm
630-10 340 680 1020 170 3000 3.04 0.2° 5.03 1.40 4.50 94.6 46.9832 94.4 94.6 50.5520
700-10 430 860 1290 215 2700 3.60 5.02 1.58 4.45 135 72.3106 132 135 77.9729
760-10 550 1100 1650 275 2500 3.70 4.98 1.60 4.30 173 91.7589 180 173 101.228
860-10 770 1540 2310 385 2200 4.82 4.95 1.86 4.21 244 145.230 245 244 160.422
950-10 1050 2100 3150 525 2000 5.40 4.91 1.92 4.09 325 204.443 338 325 227.957
1035-10 1450 2900 4350 725 1850 5.78 4.88 1.95 3.97 426 292.140 455 426 326.930
mum values and must not occur at the same time (see following In the case of types NHN and MFHFM to a coupling with shaft
table). distance S = 1000 mm (ARC-8) or S = 1500 mm (ARC-10). The
The specified, permitted shaft misalignment ΔKr for types torsional stiffness of the plate packs applies to the rated cou-
NEN/NHN and MFEFM/MFHFM applies to a shaft distance of pling torque TKN. To determine the torsional stiffness for a spe-
S = 1000 mm (ARC-8) or S = 1500 mm (ARC-10). cific operating point, e.g. for calculating torsional vibration, the
The permitted shaft misalignment ΔKr for types NEN and NHN is manufacturer must be consulted.
calculated as follows: ΔKr = (S – S1) ⋅ tan(ΔKw).
The permitted shaft misalignment ΔKr for types MFEFM and TKmax permitted only five times per hour.
MFHFM is calculated as follows:
ΔKr = (S – S1 – 2 ⋅ BF) ⋅ tan(ΔKw).
0.0° 0.1° 0.2° 0.3° 0.4°
Permitted axial misalignment ±ΔKa in mm
225-8 1.94 1.46 0.97 0.48 0.00
255-8 2.32 1.74 1.16 0.58 0.00
270-8 2.40 1.80 1.20 0.60 0.00
295-8 2.62 1.96 1.31 0.66 0.00
325-8 2.60 1.95 1.30 0.65 0.00
355-8 2.88 2.16 1.44 0.72 0.00
385-8 3.12 2.34 1.56 0.78 0.00
420-8 3.46 2.59 1.73 0.86 0.00
455-8 4.02 3.01 2.01 1.00 0.00
505-8 4.28 3.21 2.14 1.07 0.00
545-8 4.48 3.36 2.24 1.12 0.00
595-8 4.86 3.65 2.43 1.22 0.00
630-8 4.98 3.32 1.66 0.00
700-8 5.78 3.85 1.93 0.00
630-10 3.04 1.52 0.00
700-10 3.60 1.80 0.00
760-10 3.70 1.85 0.00
860-10 4.82 2.41 0.00
950-10 5.40 2.70 0.00
1035-10 5.78 2.89 0.00
Siemens MD 10.1 · 2015 6/29

© Siemens AG 2015

Types NEN/NHN

Torsionally rigid coupling types NEN and NHN with radially freely dismountable intermediate spacer and variable spacer length.
Power transmission via patented 1) conical screw connection.
NL1 S NL2
S1 LZ
G_MD10_XX_00155a
SZ
ØND1
ØND2
ØDZ
ØDA
ØD2
ØD1
6
N E, H N

torque speed Shaft moment of Order codes for bore
distance inertia diameters and tolerances
DA TKN nKmax D1/D2 ND1/ DZ SZ NL1/ S1 LZ S J are specified in catalog m
section 3
Keyway ND2 NL2 min. min.
DIN 6885
mm kNm rpm max. kgm2 kg
225-8 8.5 8500 NEN 120 147 135.0 6.0 140 16 91 123 0.19 2LC0400-0BE ■ ■ -0AZ0 29
NHN 139.7 8.0 240 272 0.21 2LC0400-0BF ■ ■ -0AZ0 33
255-8 12.7 7500 NEN 140 172 147.0 7.0 160 17 94 128 0.35 2LC0400-1BE ■ ■ -0AZ0 42
NHN 152.4 8.8 250 284 0.38 2LC0400-1BF ■ ■ -0AZ0 47
270-8 16.5 7000 NEN 150 182 172.0 7.0 170 14 96 124 0.45 2LC0400-2BE ■ ■ -0AZ0 46
NHN 177.8 7.1 300 328 0.49 2LC0400-2BF ■ ■ -0AZ0 52
295-8 23 6500 NEN 160 199 188.0 8.0 185 17 121 155 0.75 2LC0400-3BE ■ ■ -0AZ0 66
NHN 193.7 8.8 310 344 0.82 2LC0400-3BF ■ ■ -0AZ0 74
325-8 33 6000 NEN 170 214 197.0 10.5 195 20 134 174 1.27 2LC0400-4BE ■ ■ -0AZ0 93
NHN 203.0 12.5 380 420 1.42 2LC0400-4BF ■ ■ -0AZ0 108
355-8 45 5500 NEN 185 235 222.0 11.0 215 22 145 189 2.01 2LC0400-5BE ■ ■ -0AZ0 123
NHN 229.0 12.5 390 434 2.21 2LC0400-5BF ■ ■ -0AZ0 140
385-8 56 5000 NEN 205 256 238.0 12.0 240 25 151 201 3.02 2LC0400-6BE ■ ■ -0AZ0 156
NHN 244.5 14.2 450 500 3.35 2LC0400-6BF ■ ■ -0AZ0 181
420-8 70 4500 NEN 230 282 266.0 12.0 275 27 177 231 4.74 2LC0400-7BE ■ ■ -0AZ0 202
NHN 273.0 14.2 470 524 5.23 2LC0400-7BF ■ ■ -0AZ0 230
455-8 88 4200 NEN 255 308 291.0 13.0 300 29 180 238 6.81 2LC0400-8BE ■ ■ -0AZ0 244
NHN 298.5 14.2 470 528 7.43 2LC0400-8BF ■ ■ -0AZ0 274
505-8 120 3800 NEN 285 344 315.0 15.0 340 31 188 250 11.5 2LC0401-0BE ■ ■ -0AZ0 335
NHN 323.9 17.5 590 652 12.8 2LC0401-0BF ■ ■ -0AZ0 390
545-8 165 3500 NEN 300 371 346.0 17.0 350 33 202 268 16.8 2LC0401-1BE ■ ■ -0AZ0 427
NHN 355.6 20.0 600 666 18.7 2LC0401-1BF ■ ■ -0AZ0 497
595-8 210 3200 NEN 330 405 384.0 18.0 390 36 212 284 25.9 2LC0401-2BE ■ ■ -0AZ0 552
NHN 394.0 20.0 610 682 28.6 2LC0401-2BF ■ ■ -0AZ0 626
1)
this catalog.
6/30 Siemens MD 10.1 · 2015

© Siemens AG 2015

Types NEN/NHN

torque speed Shaft moment of Order codes for bore
distance inertia diameters and tolerances
DA TKN nKmax D1/D2 ND1/ DZ SZ NL1/ S1 LZ S J are specified in catalog m
section 3
DIN 6885
630-8 260 3000 NEN 340 425 409.0 19.0 400 58 281 397 40.6 2LC0401-3BE ■ ■ -0AZ0 763
NHN 419.0 20.0 630 746 43.4 2LC0401-3BF ■ ■ -0AZ0 830
700-8 340 2700 NEN 395 479 459.0 19.0 470 62 300 424 66.5 2LC0401-4BE ■ ■ -0AZ0 992
NHN 470.0 20.0 700 824 71.0 2LC0401-4BF ■ ■ -0AZ0 1078
630-10 340 3000 NEN 310 425 396.0 29.0 400 58 281 397 45.0 2LC0410-0BE ■ ■ -0AZ0 895
NHN 406.4 30.0 630 746 48.5 2LC0410-0BF ■ ■ -0AZ0 991
700-10 430 2700 NEN 350 479 459.0 26.0 470 62 300 424 75.7 2LC0410-1BE ■ ■ -0AZ0 1215
NHN 470.0 30.0 700 824 82.4 2LC0410-1BF ■ ■ -0AZ0 1352
760-10 550 2500 NEN 375 507 483.0 30.0 480 74 359 507 116 2LC0410-2BE ■ ■ -0AZ0 1557
NHN 495.0 30.0 760 908 123 2LC0410-2BF ■ ■ -0AZ0 1688
860-10 770 2200 NEN 425 574 546.0 33.0 510 82 393 557 208 2LC0410-3BE ■ ■ -0AZ0 2159
NHN 559.0 36.0 860 1024 223 2LC0410-3BF ■ ■ -0AZ0 2380
950-10 1050 2000 NEN 470 639 596.0 38.0 550 92 437 621 347 2LC0410-4BE ■ ■ -0AZ0 2948
NHN 610.0 40.0 950 1134 371 2LC0410-4BF ■ ■ -0AZ0 3234
1035-10 1450 1850 NEN 490 693 645.0 46.0 580 102 481 685 545 2LC0410-5BE ■ ■ -0AZ0 3974
6
NHN 660.4 50.0 1035 1239 586 2LC0410-5BF ■ ■ -0AZ0 4401
maximum operating speed of the coupling (see following table). coupling with maximum bores D1/D2 and S = S min.
Size Speed nN
rpm
500 600 700 800 900 1000 1200 1400 1500 2000 2500 3000 4000
mm
225-8 4962 4531 4196 3926 3703 3514 3209 2972 2872 2489 2228 2035 1765
255-8 5170 4721 4372 4091 3858 3661 3343 3097 2992 2594 2322 2121 1839
270-8 5608 5120 4741 4436 4183 3969 3625 3357 3243 2811 2516 2298 1992
295-8 5860 5351 4955 4636 4372 4148 3788 3509 3390 2938 2630 2402 2083
325-8 5969 5451 5048 4723 4454 4227 3860 3575 3455 2994 2680 2449 2123
355-8 6349 5798 5369 5024 4738 4496 4106 3803 3675 3185 2851 2605 2259
385-8 6573 6003 5559 5202 4906 4655 4252 3938 3806 3299 2953 2698 2340
420-8 6968 6363 5893 5514 5200 4935 4507 4175 4034 3497 3131 2861 2481
455-8 7290 6658 6166 5770 5441 5164 4716 4368 4221 3660 3276 2993 2596
505-8 7575 6918 6407 5995 5654 5365 4900 4539 4386 3803 3405 3111
545-8 7933 7245 6710 6279 5922 5619 5133 4754 4594 3983 3566 3258
595-8 8368 7642 7078 6623 6246 5928 5414 5015 4847 4202 3762 3438
630-8 8659 7910 7327 6858 6469 6140 5610 5198 5024 4358 3904 3569
700-8 9197 8401 7782 7283 6870 6521 5958 5521 5336 4629 4147
630-10 8410 7682 7116 6660 6283 5963 5449 5049 4880 4234 3793 3468
700-10 9128 8338 7724 7229 6819 6472 5914 5480 5296 4595 4116
760-10 9348 8540 7912 7406 6987 6632 6061 5616 5429 4711 4222
950-10 10386 9489 8792 8230 7765 7371 6737 6244 6035 5239 speed range
1035-10 10771 9841 9119 8536 8054 7646 6989 6478 6262
Ordering example:
ARPEX ARC-8 NHN coupling, size 270-8, with shaft distance
S = 1000 mm,
Article No.:
2LC0400-2BF99-0AZ0-Z
L1S+M1U+Q0Y+M13
clear text to Q0Y S = 1000 mm
Siemens MD 10.1 · 2015 6/31

© Siemens AG 2015

Type BUB

Torsionally rigid coupling type BUB with split intermediate spacer. Type BUB permits shortest shaft distances.
LG
NL1 NL2
P S1 A
SZ
S
ØND1
ØND2
ØDA
ØD1
ØDZ
ØD2
6
G_MD10_XX_00156
B U B
Size Rated Maximum Dimensions in mm Mass moment Article No. Weight

torque speed Shaft of inertia Order codes for bore
distance diameters and tolerances
DA TKN nKmax D1/D2 ND1/ DZ SZ NL1/ S1 S A P LG J are specified in catalog m
section 3
Keyway ND2 NL2
DIN
6885
225-8 8.5 8500 105 136 150 4.5 90 16 5 12 47 185 0.19 2LC0400-0AF ■ ■ -0AA0 27
255-8 12.7 7500 125 160 175 5.0 100 17 8 13 49 208 0.34 2LC0400-1AF ■ ■ -0AA0 38
270-8 16.5 7000 130 169 185 5.5 100 14 8 13 46 208 0.43 2LC0400-2AF ■ ■ -0AA0 43
295-8 23 6500 135 185 202 6.0 110 17 7 15 55 227 0.70 2LC0400-3AF ■ ■ -0AA0 61
325-8 33 6000 140 195 217 8.5 130 20 10 16 65 270 1.23 2LC0400-4AF ■ ■ -0AA0 90
355-8 45 5500 150 215 238 9.0 135 22 12 19 71 282 1.89 2LC0400-5AF ■ ■ -0AA0 116
385-8 56 5000 180 235 259 9.5 155 25 8 20 79 318 2.87 2LC0400-6AF ■ ■ -0AA0 143
420-8 70 4500 200 260 285 10.0 170 27 10 23 87 350 4.51 2LC0400-7AF ■ ■ -0AA0 187
455-8 88 4200 220 285 311 10.5 180 29 10 23 90 370 6.42 2LC0400-8AF ■ ■ -0AA0 226
505-8 120 3800 245 316 347 12.0 220 31 12 24 97 452 11.1 2LC0401-0AF ■ ■ -0AA0 322
545-8 165 3500 260 334 374 14.5 240 33 16 26 103 496 15.9 2LC0401-1AF ■ ■ -0AA0 400
595-8 210 3200 285 364 408 15.0 260 36 16 27 112 536 24.0 2LC0401-2AF ■ ■ -0AA0 507
630-8 260 3000 300 381 428 17.0 280 58 16 28 150 576 37.4 2LC0401-3AF ■ ■ -0AA0 688
700-8 340 2700 332 431 482 17.5 310 62 20 29 160 640 62.3 2LC0401-4AF ■ ■ -0AA0 936
630-10 340 3000 260 377 428 23.0 280 58 16 28 150 576 41.0 2LC0410-0AF ■ ■ -0AA0 794
700-10 430 2700 310 430 482 24.0 310 62 20 29 160 640 66.4 2LC0410-1AF ■ ■ -0AA0 1023
760-10 550 2500 320 452 512 26.0 330 74 20 34 191 680 104 2LC0410-2AF ■ ■ -0AA0 1354
860-10 770 2200 350 515 579 28.0 380 82 20 38 209 780 191 2LC0410-3AF ■ ■ -0AA0 1993
950-10 1050 2000 400 574 644 31.0 400 92 25 40 233 825 311 2LC0410-4AF ■ ■ -0AA0 2592
1035-10 1450 1850 430 615 698 38.0 420 102 25 42 257 865 477 2LC0410-5AF ■ ■ -0AA0 3332
6/32 Siemens MD 10.1 · 2015

© Siemens AG 2015

Type BUB
Split intermediate spacer permits preassembly of the coupling
halves at the factory and easy final assembly by the customer
(optional).
Power transmission via patented 1) conical screw connection.
The hubs are standard-manufactured from high-grade steel.
In the case of smaller bore diameters higher-grade material is
used, depending on the application (additional price).
Weights and mass moments of inertia apply to the entire
Ordering example:
ARPEX ARC-8 BUB coupling, size 270-8,
Article No.:
2LC0400-2AF99-0AA0-Z
L1S+M1U+M13
1)
this catalog.
Siemens MD 10.1 · 2015 6/33

© Siemens AG 2015

Types MFEFM/MFHFM

Torsionally rigid coupling types MFEFM and MFHFM with radially freely dismountable FEF or FHF transmission unit and variable
spacer length. Power transmission via patented 1) conical screw connection.
NL1 S NL2
BF LZ S1
G_MD10_XX_00157a
SZ
ØDFA
ØND1
ØND2
ØDA
ØDZ
ØD1
ØD2
6
M F E, H F M

speed distance of inertia diameters and tolerances
are specified in catalog
DA TKN nKmax D1/D2 ND1/ DFA DZ SZ NL1/ S1 LZ S BF J section 3 m
DIN 6885
225-8 8.5 8500 MFEFM 160 225 283 135.0 6.0 170 16 91 171 24 0.81 2LC0400-0AV ■ ■ -0AZ0 81
MFHFM 139.7 8.0 240 320 0.83 2LC0400-0AX ■ ■ -0AZ0 85
255-8 12.7 7500 MFEFM 180 255 313 147.0 7.0 180 17 94 178 25 1.37 2LC0400-1AV ■ ■ -0AZ0 109
MFHFM 152.4 8.8 250 334 1.39 2LC0400-1AX ■ ■ -0AZ0 114
270-8 16.5 7000 MFEFM 195 270 328 172.0 7.0 185 14 96 176 26 1.70 2LC0400-2AV ■ ■ -0AZ0 119
MFHFM 177.8 7.1 300 380 1.74 2LC0400-2AX ■ ■ -0AZ0 125
295-8 23 6500 MFEFM 210 295 353 188.0 8.0 190 17 121 215 30 2.55 2LC0400-3AV ■ ■ -0AZ0 153
MFHFM 193.7 8.8 310 404 2.62 2LC0400-3AX ■ ■ -0AZ0 161
325-8 33 6000 MFEFM 230 325 389 197.0 10.5 210 20 134 246 36 4.30 2LC0400-4AV ■ ■ -0AZ0 215
MFHFM 203.0 12.5 380 492 4.45 2LC0400-4AX ■ ■ -0AZ0 231
355-8 45 5500 MFEFM 255 355 419 222.0 11.0 230 22 145 267 39 6.45 2LC0400-5AV ■ ■ -0AZ0 270
MFHFM 229.0 12.5 390 512 6.65 2LC0400-5AX ■ ■ -0AZ0 288
385-8 56 5000 MFEFM 275 385 465 238.0 12.0 250 25 151 285 42 10.0 2LC0400-6AV ■ ■ -0AZ0 354
MFHFM 244.5 14.2 450 584 10.4 2LC0400-6AX ■ ■ -0AZ0 379
420-8 70 4500 MFEFM 300 420 507 266.0 12.0 270 27 177 325 47 15.3 2LC0400-7AV ■ ■ -0AZ0 454
MFHFM 273.0 14.2 470 618 15.8 2LC0400-7AX ■ ■ -0AZ0 483
455-8 88 4200 MFEFM 325 455 542 291.0 13.0 295 29 180 334 48 22.2 2LC0400-8AV ■ ■ -0AZ0 563
MFHFM 298.5 14.2 470 624 22.8 2LC0400-8AX ■ ■ -0AZ0 593
505-8 120 3800 MFEFM 361 505 601 315.0 15.0 325 31 188 354 52 37.9 2LC0401-0AV ■ ■ -0AZ0 773
MFHFM 323.9 17.5 590 756 39.2 2LC0401-0AX ■ ■ -0AZ0 829
545-8 165 3500 MFEFM 389 545 641 346.0 17.0 350 33 202 378 55 54.3 2LC0401-1AV ■ ■ -0AZ0 959
MFHFM 355.6 20.0 600 776 56.2 2LC0401-1AX ■ ■ -0AZ0 1029
595-8 210 3200 MFEFM 425 595 691 384.0 18.0 385 36 212 404 60 82.8 2LC0401-2AV ■ ■ -0AZ0 1236
MFHFM 394.0 20.0 610 802 85.5 2LC0401-2AX ■ ■ -0AZ0 1310
1)
this catalog.
6/34 Siemens MD 10.1 · 2015

© Siemens AG 2015

Types MFEFM/MFHFM

DA TKN nKmax D1/D2 ND1/ DFA DZ SZ NL1/ S1 LZ S BF J are specified in catalog m
ND2 NL2 section 3
Keyway min. min.
DIN 6885
630-8 260 3000 MFEFM 450 630 736 409.0 19.0 405 58 281 549 76 116 2LC0401-3AV ■ ■ -0AZ0 1567
MFHFM 419.0 20.0 630 898 119 2LC0401-3AX ■ ■ -0AZ0 1634
700-8 340 2700 MFEFM 500 700 816 459.0 19.0 450 62 300 586 81 194 2LC0401-4AV ■ ■ -0AZ0 2106
MFHFM 470.0 20.0 700 986 198 2LC0401-4AX ■ ■ -0AZ0 2192
630-10 340 3000 MFEFM 450 630 746 396.0 29.0 405 58 281 549 76 121 2LC0410-0AV ■ ■ -0AZ0 1631
MFHFM 406.4 30.0 630 898 125 2LC0410-0AX ■ ■ -0AZ0 1727
700-10 430 2700 MFEFM 500 700 816 459.0 26.0 450 62 300 586 81 197 2LC0410-1AV ■ ■ -0AZ0 2136
MFHFM 470.0 30.0 700 986 203 2LC0410-1AX ■ ■ -0AZ0 2273
760-10 550 2500 MFEFM 545 760 878 483.0 30.0 490 74 359 701 97 301 2LC0410-2AV ■ ■ -0AZ0 2810
MFHFM 495.0 30.0 760 1102 308 2LC0410-2AX ■ ■ -0AZ0 2940
860-10 770 2200 MFEFM 615 860 991 546.0 33.0 555 82 393 769 106 547 2LC0410-3AV ■ ■ -0AZ0 3993
MFHFM 559.0 36.0 860 1236 563 2LC0410-3AX ■ ■ -0AZ0 4213
950-10 1050 2000 MFEFM 680 950 1083 596.0 38.0 615 92 437 857 118 892 2LC0410-4AV ■ ■ -0AZ0 5368
MFHFM 610.0 40.0 950 1370 916 2LC0410-4AX ■ ■ -0AZ0 5654
1035-10 1450 1850 MFEFM 740 1035 1168 645.0 46.0 670 102 481 947 131 1371 2LC0410-5AV ■ ■ -0AZ0 7005
6
MFHFM 660.4 50.0 1035 1501 1412 2LC0410-5AX ■ ■ -0AZ0 7432
FEF or FHF transmission unit preassembled at the factory In the case of individual order of the intermediate spacer, the
enables easy final assembly by the customer. length (LZ) must be specified.
maximum operating speed of the coupling (see following table). coupling with maximum bores D1/D2 and S = S min.
Permitted shaft distance S of type MFHFM relative to speed
Size Speed nN
rpm
500 600 700 800 900 1000 1200 1400 1500 2000 2500 3000 4000
mm
225-8 5010 4579 4244 3974 3751 3562 3257 3020 2920 2537 2276 2083 1813
255-8 5220 4771 4422 4141 3908 3711 3393 3147 3042 2644 2372 2171 1889
270-8 5660 5172 4793 4488 4235 4021 3677 3409 3295 2863 2568 2350 2044
295-8 5920 5411 5015 4696 4432 4208 3848 3569 3450 2998 2690 2462 2143
325-8 6041 5523 5120 4795 4526 4299 3932 3647 3527 3066 2752 2521 2195
355-8 6427 5876 5447 5102 4816 4574 4184 3881 3753 3263 2929 2683 2337
385-8 6657 6087 5643 5286 4990 4739 4336 4022 3890 3383 3037 2782 2424
420-8 7062 6457 5987 5608 5294 5029 4601 4269 4128 3591 3225 2955 2575
455-8 7386 6754 6262 5866 5537 5260 4812 4464 4317 3756 3372 3089 2692
505-8 7679 7022 6511 6099 5758 5469 5004 4643 4490 3907 3509 3215
545-8 8043 7355 6820 6389 6032 5729 5243 4864 4704 4093 3676 3368
595-8 8488 7762 7198 6743 6366 6048 5534 5135 4967 4322 3882 3558
630-8 8811 8062 7479 7010 6621 6292 5762 5350 5176 4510 4056 3721
700-8 9359 8563 7944 7445 7032 6683 6120 5683 5498 4791 4309
630-10 8562 7834 7268 6812 6435 6115 5601 5201 5032 4386 3945 3620
700-10 9290 8500 7886 7391 6981 6634 6076 5642 5458 4757 4278
760-10 9542 8734 8106 7600 7181 6826 6255 5810 5623 4905 4416
950-10 10622 9725 9028 8466 8001 7607 6973 6480 6271 5475 speed range
1035-10 11033 10103 9381 8798 8316 7908 7251 6740 6524
Ordering example:
ARPEX ARC-8 MFHFM coupling, size 270-8, with shaft distance
S = 1000 mm,
Article No.:
2LC0400-2AX99-0AZ0-Z
L1W+M1X+Q0Y+M13
clear text to Q0Y: S = 1000 mm
Siemens MD 10.1 · 2015 6/35

© Siemens AG 2015

Plate pack ARC-8/-10
S1
Figure 1 Figure 2 Figure 3

ØDA
6
G_MD10_EN_00158
Plate packs of the ARC-8 series up to size 595-8 comprise ring Plate packs of the ARC-10 series in all sizes comprise side-bar
plates (Fig. 1) and from size 630-8 side-bar plates (Fig. 2). plates (Fig. 3).
Dimensions in mm Plate pack Mass moment of inertia Article No. Weight
Size Series
S1 J m
kgm2 kg
225-8 16 ARC-8 0.02 2LC0400-0AT00-0AA0 2.4
255-8 17 ARC-8 0.03 2LC0400-1AT00-0AA0 3.1
270-8 14 ARC-8 0.04 2LC0400-2AT00-0AA0 3.4
295-8 17 ARC-8 0.07 2LC0400-3AT00-0AA0 4.8
325-8 20 ARC-8 0.12 2LC0400-4AT00-0AA0 7.2
355-8 22 ARC-8 0.20 2LC0400-5AT00-0AA0 9.8
385-8 25 ARC-8 0.30 2LC0400-6AT00-0AA0 12.7
420-8 27 ARC-8 0.46 2LC0400-7AT00-0AA0 16.2
455-8 29 ARC-8 0.64 2LC0400-8AT00-0AA0 19.2
505-8 31 ARC-8 1.01 2LC0401-0AT00-0AA0 24.5
545-8 33 ARC-8 1.47 2LC0401-1AT00-0AA0 30.8
595-8 36 ARC-8 2.26 2LC0401-2AT00-0AA0 39.8
630-8 58 ARC-8 4.03 2LC0401-3AT00-0AA0 67.2
700-8 62 ARC-8 6.33 2LC0401-4AT00-0AA0 84.5
630-10 58 ARC-10 5.00 2LC0410-0AT00-0AA0 78.0
700-10 62 ARC-10 7.85 2LC0410-1AT00-0AA0 98.0
760-10 74 ARC-10 13.73 2LC0410-2AT00-0AA0 147
860-10 82 ARC-10 24.49 2LC0410-3AT00-0AA0 203
950-10 92 ARC-10 41.26 2LC0410-4AT00-0AA0 277
1035-10 102 ARC-10 65.64 2LC0410-5AT00-0AA0 374
The plate pack of the ARC-8/-10 series is readily available as a Ordering example:
spare part. ARPEX ARC-8 plate pack, size 225-8,
complete with screw connection
The plate pack is delivered with conical screw connection.
Article No.:
2LC0400-0AT00-0AA0
6/36 Siemens MD 10.1 · 2015

© Siemens AG 2015

Torsionally Rigid All-Steel Couplings — ARPEX ARP-6 Series
General information
■ Overview
Coupling can be used in potentially explosive atmospheres

in accordance with the current ATEX Directive.
■ Benefits
6
ARPEX couplings of the ARP-6 series are outstanding for their ate unit can also be optionally designed to API 671. A special
application-optimized construction. The two types NAN and catcher device serves to secure the intermediate spacer in the
MCECM have been specially designed for drives with uniform to event of plate breakage. Their use in potentially explosive atmo-
medium loads and at the same time meet the requirements of spheres in accordance with the current ATEX Directive is possi-
API 610. The type MCECM with preassembled CEC intermedi- ble.
■ Application
ARPEX series ARP-6 couplings have been specially developed
for pump drives and specifically for centrifugal pump drives.
Special care was taken to meet the requirements of API 610 and
API 671 (API = American Petroleum Institute). Power is transmit-
ted via close-fitting bolts and nuts from size 310-6 with conical
screw connection and plate packs in hexagonal design. Torques
of between 100 and 17000 Nm can be transmitted at a permitted
angular misalignment of 0.7°. The closed flange shape and a
compact construction permit high peripheral speeds and high
speeds. The intermediate spacer can be fitted radially without
moving the connected units.
Main areas of application for the ARP-6 series:
• Centrifugal pumps
• Boiler feed pumps
• Propeller pumps
• Wing pumps
• Pipeline pumps
• Turbo compressors
• Screw compressors
• Turbo blowers
• Axial, radial blowers
• Rotary-piston blowers
• Fans
Siemens MD 10.1 · 2015 6/37

© Siemens AG 2015

General information
■ Design
NAN: The design of an ARPEX NAN coupling of the ARP-6 series MCECM: The design of an ARPEX MCECM coupling of the
is shown in the following illustration. The plate packs are bolted ARP-6 series is shown in the following illustration. Bolted be-
alternately between the flanges of the coupling hubs and the in- tween two hubs is the CEC transmission unit, the preassembled
termediate spacer. Up to size 298-6 close-fitting bolts and from plate packs of which are bolted alternately between flanges and
size 325-6 conical screw connections are used for fastening. intermediate spacer. Up to size 275-6 close-fitting bolts and from
The intermediate spacer is available from stock in various fixed size 310-6 conical screw connections are used for fastening.
lengths. Hubs are designed with threaded pull-off holes. The intermediate spacer is available from stock in various fixed
lengths. Jumbo hubs for large bore diameters can be optionally
used.
Type MCECM Type NAN
Plate pack
Intermediate flange
Intermediate
6
spacer
Intermediate spacer
Collar nut
Collar nut
Guard ring
Guard ring Plate pack
Hub
Close-fitting bolt
Close-fitting bolt Hub
G_MD10_EN_00159a
Design of the ARPEX coupling, ARP-6 series

Variants of the ARPEX coupling, ARP-6 series
Types
NAN Variant with intermediate spacer, various fixed lengths
available from stock Dimension sheets and further information are available on re-
MCECM Variant with preassembled intermediate unit and spacer
quest.
machined on all sides, various fixed lengths available from
stock
■ Technical data
Power ratings, type NAN
torque torque speed ±ΔKa ±ΔKw ±ΔKr CT
TKN TKmax TKOL TKW nKmax S= S= S= S= S= S= S= S= S= S=
100 140 180 200 250 100 140 180 200 250
mm mm mm mm mm mm mm mm mm mm
Nm Nm Nm Nm rpm mm mm mm mm mm mm MNm/ MNm/ MNm/ MNm/ MNm/
rad rad rad rad rad
88-6 190 270 450 70 21700 1.10 0.7° 1.15 1.64 – – – 0.04 0.04 – – –
115-6 270 410 680 110 16600 1.81 1.15 1.64 2.13 – – 0.09 0.09 0.08 – –
135-6 580 870 1450 230 12700 2.02 1.14 1.62 2.11 – – 0.21 0.19 0.17 – –
150-6 660 100 1650 270 11400 2.41 1.14 1.62 2.11 2.36 2.97 0.27 0.25 0.24 0.23 0.21
176-6 1220 1900 3100 490 9750 2.75 1.11 1.6 2.09 2.33 2.94 0.44 0.40 0.38 0.36 0.34
185-6 1875 2900 4700 750 9300 2.85 1.09 1.58 2.06 2.31 2.92 0.56 0.52 0.49 0.47 0.44
212-6 2850 4230 7200 1200 8100 3.06 1.10 1.59 2.08 2.32 2.93 0.81 0.75 0.70 0.67 0.62
225-6 4200 6300 10500 1700 7650 3.14 – 1.59 2.08 2.32 2.93 – 0.85 0.81 0.79 0.74
256-6 5750 8700 15000 2300 6700 3.69 – 1.56 2.05 2.3 2.91 – 1.37 1.31 1.29 1.22
272-6 8050 12000 20000 3200 6300 3.85 – 1.51 2 2.25 2.86 – 1.44 1.39 1.36 1.3
298-6 10000 15000 25000 4000 5150 4.19 – 1.47 1.95 2.2 2.81 – 1.47 1.43 1.41 1.37
325-6 12000 18000 30000 4800 4700 4.45 – – 1.93 2.17 2.79 – – 2.48 2.44 2.34
6/38 Siemens MD 10.1 · 2015

© Siemens AG 2015

General information
Power ratings, type MCECM
torque torque speed
±ΔKa ±ΔKw ±ΔKr CT
TKN TKmax TKOL TKW nKmax S= S= S= S= S= S= S= S= S= S=
100 140 180 200 250 100 140 180 200 250
mm mm mm mm mm mm mm mm mm mm
Nm Nm Nm Nm rpm mm mm mm mm mm mm MNm/ MNm/ MNm/ MNm/
rad rad rad rad
64-4 100 150 250 40 22500 0.80 0.7° 0.78 1.27 – – – 0.009 0.008 – – –
96-6 210 310 530 85 19900 1.15 0.78 1.27 – – – 0.06 0.05 – – –
120-6 490 740 1250 200 15900 1.47 0.65 1.14 1.62 – – 0.17 0.15 0.13 – –
142-6 925 1400 2300 370 13400 1.73 – 1.04 1.53 – – – 0.28 0.25 – –
162-6 1600 2400 4000 640 11800 2.07 – 0.92 1.40 1.65 2.26 – 0.43 0.39 0.38 0.34
190-6 2500 3800 6300 1000 10000 2.36 – 0.93 1.42 1.66 2.27 – 0.71 0.65 0.63 0.57
214-6 3900 5900 9800 1600 8900 2.67 – 0.78 1.27 1.51 2.13 – 1.01 0.94 0.92 0.85
230-6 5200 7800 13000 2100 8300 2.88 – – 1.25 1.49 2.10 – – 1.36 1.32 1.22
245-6 7000 10500 18000 2800 7800 2.99 – – 1.00 1.25 1.86 – – 1.49 1.45 1.37
275-6 9800 15000 25000 4000 6250 3.38 – – – 1.22 1.83 – – – 1.65 1.58
310-6 12900 20000 33000 5200 5550 3.85 – – – – 1.64 – – – – 2.96
345-6 17000 26000 43000 6800 5000 4.24 – – – – 1.61 – – – – 4.12
6
mum values and must not occur at the same time (see following The torsional stiffness of the plate packs applies to the rated
table). The permitted shaft misalignment ΔKr applies to the shaft coupling torque TKN. To determine the torsional stiffness for a
distance S specified in each case. specific operating point, e.g. for calculating torsional vibration,
the manufacturer must be consulted.
TKmax permitted only five times per hour.
Permitted shaft misalignments, type NAN

0.0° 0.1° 0.2° 0.3° 0.4° 0.5° 0.6° 0.7°
88-6 1.10 0.94 0.79 0.63 0.47 0.31 0.16 0.00
115-6 1.81 1.55 1.29 1.03 0.77 0.52 0.26 0.00
135-6 2.02 1.73 1.44 1.15 0.86 0.58 0.29 0.00
150-6 2.41 2.06 1.72 1.38 1.03 0.69 0.34 0.00
176-6 2.75 2.36 1.96 1.57 1.18 0.79 0.39 0.00
185-6 2.85 2.45 2.04 1.63 1.22 0.82 0.41 0.00
212-6 3.06 2.63 2.19 1.75 1.31 0.88 0.44 0.00
225-6 3.14 2.69 2.24 1.80 1.35 0.90 0.45 0.00
256-6 3.69 3.16 2.64 2.11 1.58 1.05 0.53 0.00
272-6 3.85 3.30 2.75 2.20 1.65 1.10 0.55 0.00
298-6 4.19 3.59 2.99 2.39 1.80 1.20 0.60 0.00
325-6 4.45 3.82 3.18 2.54 1.91 1.27 0.64 0.00
Permitted shaft misalignments, type MCECM

0.0° 0.1° 0.2° 0.3° 0.4° 0.5° 0.6° 0.7°
64-4 0.80 0.68 0.57 0.46 0.34 0.23 0.11 0.00
96-6 1.15 0.99 0.82 0.66 0.49 0.33 0.16 0.00
120-6 1.47 1.26 1.05 0.84 0.63 0.42 0.21 0.00
142-6 1.73 1.48 1.23 0.99 0.74 0.49 0.25 0.00
162-6 2.07 1.77 1.48 1.18 0.89 0.59 0.30 0.00
190-6 2.36 2.02 1.68 1.35 1.01 0.67 0.34 0.00
214-6 2.67 2.29 1.91 1.53 1.14 0.76 0.38 0.00
230-6 2.88 2.47 2.06 1.65 1.23 0.82 0.41 0.00
245-6 2.99 2.56 2.13 1.71 1.28 0.85 0.43 0.00
275-6 3.38 2.90 2.41 1.93 1.45 0.97 0.48 0.00
310-6 3.85 3.30 2.75 2.20 1.65 1.10 0.55 0.00
345-6 4.24 3.64 3.03 2.42 1.82 1.21 0.61 0.00
Siemens MD 10.1 · 2015 6/39

© Siemens AG 2015

Type NAN

Torsionally rigid type NAN coupling with radially freely dismountable intermediate spacer and catcher device for securing the inter-
mediate spacer in the event of plate breakage. Standard coupling type in accordance with API 610.
LG
NL1 S NL2
S1
G_MD10_XX_00160
SZ
ØND1
ØND2
ØDA
ØDZ
ØD1
ØD2
6
N A N
Size Rated Maxi- Dimensions in mm Mass Article No. Weight

DA TKN nKmax D1/D2 ND1/ND2 DZ SZ NL1/ S1 S LG J are specified in catalog m
NL2 section 3
Keyway
DIN 6885
88-6 190 21700 35 48 45 2.5 40 6 100 180 0.001 2LC0450-0AD ■ ■ -0AA0 1.6
140 220 0.001 2LC0450-0AD ■ ■ -0AB0 1.7
115-6 270 16600 55 75 72 2.5 55 6 100 210 0.005 2LC0450-1AD ■ ■ -0AA0 3.2
140 250 0.005 2LC0450-1AD ■ ■ -0AB0 3.4
180 290 0.005 2LC0450-1AD ■ ■ -0AC0 3.6
135-6 580 12700 65 86 84 2.5 65 7 100 230 0.011 2LC0450-2AD ■ ■ -0AA0 5.2
140 270 0.012 2LC0450-2AD ■ ■ -0AB0 5.4
180 310 0.012 2LC0450-2AD ■ ■ -0AC0 5.6
150-6 660 11400 75 101 99 2.5 75 7 100 250 0.019 2LC0450-3AD ■ ■ -0AA0 7.2
140 290 0.020 2LC0450-3AD ■ ■ -0AB0 7.5
180 330 0.021 2LC0450-3AD ■ ■ -0AC0 7.7
200 350 0.021 2LC0450-3AD ■ ■ -0AD0 7.8
250 400 0.022 2LC0450-3AD ■ ■ -0AE0 8.1
176-6 1220 9750 85 117 114 2.5 85 9 100 270 0.041 2LC0450-4AD ■ ■ -0AA0 11.4
140 310 0.042 2LC0450-4AD ■ ■ -0AB0 11.7
180 350 0.043 2LC0450-4AD ■ ■ -0AC0 12.0
200 370 0.044 2LC0450-4AD ■ ■ -0AD0 12.1
250 420 0.045 2LC0450-4AD ■ ■ -0AE0 12.4
185-6 1875 9300 90 122 120 3.0 90 11 100 280 0.056 2LC0450-5AD ■ ■ -0AA0 13.5
140 320 0.057 2LC0450-5AD ■ ■ -0AB0 13.9
180 360 0.058 2LC0450-5AD ■ ■ -0AC0 14.2
200 380 0.058 2LC0450-5AD ■ ■ -0AD0 14.4
250 430 0.060 2LC0450-5AD ■ ■ -0AE0 14.8
6/40 Siemens MD 10.1 · 2015

© Siemens AG 2015

Type NAN
DA TKN nKmax D1/D2 ND1/ND2 DZ SZ NL1/ S1 S LG J are specified in catalog m
NL2 section 3
Keyway
DIN 6885
212-6 2850 8100 100 134 131 3.0 100 10 100 300 0.095 2LC0450-6AD ■ ■ -0AA0 18.3
140 340 0.097 2LC0450-6AD ■ ■ -0AB0 18.6
180 380 0.098 2LC0450-6AD ■ ■ -0AC0 19.0
200 400 0.099 2LC0450-6AD ■ ■ -0AD0 19.2
250 450 0.101 2LC0450-6AD ■ ■ -0AE0 19.7
225-6 4200 7650 105 141 139 4.0 105 10 140 350 0.134 2LC0450-7AD ■ ■ -0AB0 22.8
180 390 0.136 2LC0450-7AD ■ ■ -0AC0 23.3
200 410 0.137 2LC0450-7AD ■ ■ -0AD0 23.6
250 460 0.140 2LC0450-7AD ■ ■ -0AE0 24.2
256-6 5750 6700 120 163 162 5.0 120 12 140 380 0.262 2LC0450-8AD ■ ■ -0AB0 34.3
180 420 0.267 2LC0450-8AD ■ ■ -0AC0 35.1
200 440 0.270 2LC0450-8AD ■ ■ -0AD0 35.5
250 490 0.276 2LC0450-8AD ■ ■ -0AE0 36.5
272-6 8050 6300 125 171 170 5.0 130 16 140 400 0.373 2LC0451-0AD ■ ■ -0AB0 42.9
180 440 0.378 2LC0451-0AD ■ ■ -0AC0 43.7
■ ■
6
200 460 0.381 2LC0451-0AD -0AD0 44.1
250 510 0.388 2LC0451-0AD ■ ■ -0AE0 45.1
298-6 10000 5150 140 189 186 6.0 140 20 140 420 0.559 2LC0451-1AD ■ ■ -0AB0 53.6
180 460 0.567 2LC0451-1AD ■ ■ -0AC0 54.7
200 480 0.572 2LC0451-1AD ■ ■ -0AD0 55.2
250 530 0.582 2LC0451-1AD ■ ■ -0AE0 56.5
325-6 12000 4700 150 203 200 6.5 150 22 180 480 0.851 2LC0451-2AD ■ ■ -0AC0 69.4
200 500 0.857 2LC0451-2AD ■ ■ -0AD0 70.0
250 550 0.872 2LC0451-2AD ■ ■ -0AE0 71.6
Hubs are designed with threaded pull-off holes. Ordering example:
Type NAN with spacer machined on all sides, available in vari- ARPEX ARP-6 NAN coupling, size 135-6, with shaft distance
ous standard lengths. S = 140 mm,
A spacers are also available in the following inch dimensions: Bore ∅D1 50H7 mm, with keyway to DIN 6885 and set screw,
S = 3.5"/5"/7"/8"/10". Bore ∅D2 60K7 mm, with keyway to DIN 6885 and set screw.
Other spacer lengths are available on request.
Article No.:
Weights and mass moments of inertia apply to the entire 2LC0450-2AD99-0AB0-Z
coupling with maximum bores D1/D2. L1C+M1E+M13
Siemens MD 10.1 · 2015 6/41

© Siemens AG 2015

Type MCECM

Torsionally rigid type MCECM coupling with radially freely dismountable intermediate unit and catcher device for securing the inter-
mediate spacer in the event of plate breakage. Standard coupling type in accordance with API 610. Coupling type in accordance
with API 671 possible.
LG
G_MD10_XX_00161
NL1 S NL2
BF S1
SZ
ØND1
ØDA
ØD1
ØND2
ØDZ
ØD2
M C E C M
6
P P
A A
ØDA=ØND2
ØDA=ØND1
ØDA=ØND1
ØND2
ØD2
ØD1
ØD1
ØD2
J C E C M J C E C J

DA TKN nKmax D1/D2 ND1 ND2 DZ SZ NL1/ S1 BF A P S LG J section 3 m
Keyway NL2
DIN 6885
64-4 100 22500 JCECJ 46 46 64 64 28 3.0 25 6 14.5 5 42 100 150 0.001 2LC0460-0AG ■ ■ -0AA0 1.6
140 190 0.001 2LC0460-0AG ■ ■ -0AB0 1.7
96-6 210 19900 MCECM 50 50 70 70 45 2.5 50 6 15 – – 100 200 0.004 2LC0460-1AP ■ ■ -0AA0 3.8
140 240 0.005 2LC0460-1AP ■ ■ -0AB0 3.9
JCECM 65 50 96 70 6 68 100 200 0.006 2LC0460-1AH ■ ■ -0AA0 4.4
140 240 0.006 2LC0460-1AH ■ ■ -0AB0 4.5
JCECJ 65 65 96 96 100 200 0.008 2LC0460-1AG ■ ■ -0AA0 5.0
140 240 0.008 2LC0460-1AG ■ ■ -0AB0 5.1
120-6 490 15900 MCECM 65 65 94 94 60 3.6 65 7 20 – – 100 230 0.016 2LC0460-2AP ■ ■ -0AA0 8.1
140 270 0.016 2LC0460-2AP ■ ■ -0AB0 8.3
180 310 0.016 2LC0460-2AP ■ ■ -0AC0 8.5
JCECM 80 65 120 94 6 88 100 230 0.020 2LC0460-2AH ■ ■ -0AA0 9.1
140 270 0.020 2LC0460-2AH ■ ■ -0AB0 9.3
180 310 0.020 2LC0460-2AH ■ ■ -0AC0 9.5
JCECJ 80 80 120 120 100 230 0.025 2LC0460-2AG ■ ■ -0AA0 10.2
140 270 0.025 2LC0460-2AG ■ ■ -0AB0 10.4
180 310 0.025 2LC0460-2AG ■ ■ -0AC0 10.6
142-6 925 13400 MCECM 75 75 109 109 72 4.8 75 9 23 – – 140 290 0.035 2LC0460-3AP ■ ■ -0AB0 13.2
180 330 0.035 2LC0460-3AP ■ ■ -0AC0 13.6
JCECM 95 75 142 109 8 100 140 290 0.045 2LC0460-3AH ■ ■ -0AB0 15.0
180 330 0.046 2LC0460-3AH ■ ■ -0AC0 15.3
JCECJ 95 95 142 142 140 290 0.055 2LC0460-3AG ■ ■ -0AB0 16.8
180 330 0.056 2LC0460-3AG ■ ■ -0AC0 17.1
6/42 Siemens MD 10.1 · 2015

© Siemens AG 2015

Type MCECM
Keyway NL2
DIN 6885
162-6 1600 11800 MCECM 85 85 122 122 84.5 5.5 85 11 27 – – 140 310 0.066 2LC0460-4AP ■ ■ -0AB0 19.2
180 350 0.067 2LC0460-4AP ■ ■ -0AC0 19.7
200 370 0.067 2LC0460-4AP ■ ■ -0AD0 19.9
250 420 0.068 2LC0460-4AP ■ ■ -0AE0 20.4
JCECM 108 85 162 122 10 113 140 310 0.087 2LC0460-4AH ■ ■ -0AB0 22.0
180 350 0.088 2LC0460-4AH ■ ■ -0AC0 22.4
200 370 0.088 2LC0460-4AH ■ ■ -0AD0 22.6
250 420 0.089 2LC0460-4AH ■ ■ -0AE0 23.2
JCECJ 108 108 162 162 140 310 0.108 2LC0460-4AG ■ ■ -0AB0 24.8
180 350 0.109 2LC0460-4AG ■ ■ -0AC0 25.3
200 370 0.109 2LC0460-4AG ■ ■ -0AD0 25.5
250 420 0.110 2LC0460-4AG ■ ■ -0AE0 26.0
190-6 2500 10000 MCECM 105 105 145 145 97.6 7.0 105 10 27 – – 140 350 0.136 2LC0460-5AP ■ ■ -0AB0 28.4
180 390 0.138 2LC0460-5AP ■ ■ -0AC0 29.0
200 410 0.138 2LC0460-5AP ■ ■ -0AD0 29.4
6
250 460 0.140 2LC0460-5AP ■ ■ -0AE0 30.1
JCECM 125 105 190 145 12 135 140 350 0.186 2LC0460-5AH ■ ■ -0AB0 33.8
180 390 0.187 2LC0460-5AH ■ ■ -0AC0 34.4
200 410 0.188 2LC0460-5AH ■ ■ -0AD0 34.7
250 460 0.190 2LC0460-5AH ■ ■ -0AE0 35.5
JCECJ 125 125 190 190 140 350 0.236 2LC0460-5AG ■ ■ -0AB0 39.2
180 390 0.238 2LC0460-5AG ■ ■ -0AC0 39.8
200 410 0.238 2LC0460-5AG ■ ■ -0AD0 40.1
250 460 0.240 2LC0460-5AG ■ ■ -0AE0 40.9
214-6 3900 8900 MCECM 115 115 164 164 110 9.1 115 10 33 – – 140 370 0.251 2LC0460-6AP ■ ■ -0AB0 41.7
180 410 0.253 2LC0460-6AP ■ ■ -0AC0 42.6
200 430 0.254 2LC0460-6AP ■ ■ -0AD0 43.1
250 480 0.257 2LC0460-6AP ■ ■ -0AE0 44.2
JCECM 140 115 214 164 12 145 140 370 0.339 2LC0460-6AH ■ ■ -0AB0 48.9
180 410 0.342 2LC0460-6AH ■ ■ -0AC0 49.8
200 430 0.343 2LC0460-6AH ■ ■ -0AD0 50.3
250 480 0.346 2LC0460-6AH ■ ■ -0AE0 51.4
JCECJ 140 140 214 214 140 370 0.428 2LC0460-6AG ■ ■ -0AB0 56.2
180 410 0.430 2LC0460-6AG ■ ■ -0AC0 57.1
200 430 0.431 2LC0460-6AG ■ ■ -0AD0 57.6
250 480 0.434 2LC0460-6AG ■ ■ -0AE0 58.7
230-6 5200 8300 MCECM 125 125 174 174 123 8.8 125 12 33 – – 180 430 0.359 2LC0460-7AP ■ ■ -0AC0 51.5
200 450 0.361 2LC0460-7AP ■ ■ -0AD0 52.0
250 500 0.365 2LC0460-7AP ■ ■ -0AE0 53.2
JCECM 155 125 230 174 14 158 180 430 0.484 2LC0460-7AH ■ ■ -0AC0 60.0
200 450 0.485 2LC0460-7AH ■ ■ -0AD0 60.5
250 500 0.489 2LC0460-7AH ■ ■ -0AE0 61.7
JCECJ 155 155 230 230 180 430 0.610 2LC0460-7AG ■ ■ -0AC0 68.7
200 450 0.611 2LC0460-7AG ■ ■ -0AD0 69.2
250 500 0.615 2LC0460-7AG ■ ■ -0AE0 70.5
245-6 7000 7800 MCECM 130 130 185 185 128 12.2 130 16 41 – – 180 440 0.532 2LC0460-8AP ■ ■ -0AC0 67.0
200 460 0.534 2LC0460-8AP ■ ■ -0AD0 67.7
250 510 0.540 2LC0460-8AP ■ ■ -0AE0 69.5
JCECM 165 130 245 185 16 170 180 440 0.693 2LC0460-8AH ■ ■ -0AC0 76.2
200 460 0.695 2LC0460-8AH ■ ■ -0AD0 76.9
250 510 0.701 2LC0460-8AH ■ ■ -0AE0 78.6
JCECJ 165 165 245 245 180 440 0.855 2LC0460-8AG ■ ■ -0AC0 85.5
200 460 0.857 2LC0460-8AG ■ ■ -0AD0 86.2
250 510 0.863 2LC0460-8AG ■ ■ -0AE0 88.0
Siemens MD 10.1 · 2015 6/43

© Siemens AG 2015

Type MCECM
Keyway NL2
DIN 6885
275-6 9800 6250 MCECM 150 150 213 213 148 12.6 150 20 40 – – 200 500 0.917 2LC0461-0AP ■ ■ -0AD0 91.1
250 550 0.927 2LC0461-0AP ■ ■ -0AE0 93.3
JCECM 185 150 275 213 16 200 200 500 1.207 2LC0461-0AH ■ ■ -0AD0 104.4
250 550 1.217 2LC0461-0AH ■ ■ -0AE0 106.5
JCECJ 185 185 275 275 200 500 1.499 2LC0461-0AG ■ ■ -0AD0 118.0
250 550 1.509 2LC0461-0AG ■ ■ -0AE0 120.1
310-6 12900 5550 MCECM 170 170 240 240 160 13.5 170 22 47 – – 250 590 1.670 2LC0461-1AP ■ ■ -0AE0 131.7
JCECM 205 170 310 240 16 220 2.228 2LC0461-1AH ■ ■ -0AE0 153.2
JCECJ 205 205 310 310 2.788 2LC0461-1AG ■ ■ -0AE0 175.0
345-6 17000 5000 MCECM 190 190 267 267 172 18.5 190 24 47 – – 250 630 2.742 2LC0461-2AP ■ ■ -0AE0 176.1
JCECM 230 190 345 267 20 245 3.684 2LC0461-2AH ■ ■ -0AE0 205.1
JCECJ 230 230 345 345 4.629 2LC0461-2AG ■ ■ -0AE0 234.3
6
Hubs are designed with threaded pull-off holes. Ordering example:
E spacers are also available in the following inch dimensions on ARPEX ARP-6 MCECM coupling, size 120-6, with shaft distance
request: S = 3.5"/5"/7"/8"/10". S = 140 mm,
Other spacer lengths are available on request. Bore ∅D1 50H7 mm, with keyway to DIN 6885 and set screw,
Plate packs in the CEC intermediate unit assembled at the Bore ∅D2 60K7 mm, with keyway to DIN 6885 and set screw.
factory.
Jumbo hub for large shaft diameters. Article No.:
2LC0460-2AP99-0AB0-Z
Weights and mass moments of inertia apply to the entire L1C+M1E+M13
6/44 Siemens MD 10.1 · 2015

© Siemens AG 2015

Plate pack ARP-6

S1 S1
Figure 1 Figure 2
ØDL
ØDL
G_MD10_EN_00162a
6
Mainly ring plates (Fig. 1) are used for the plate packs. Sizes 298-6 and 325-6 comprise side-bar plates (Fig. 2).
The plate pack of the ARP-6 series is delivered with screw connection and is readily available as a spare part.
• With outside diameters up to DA = 300 mm, close-fitting bolts with collar nuts are used
• From outside diameter DA = 300 mm, patented 1) conical screw connections are used
Plate pack
Size Plate size
DA DL S1 J m
kgm2 kg
Plate pack NAN
88-6 78 6 0.0001 2LC0450-0AF00-0AA0 0.1
115-6 105 6 0.0003 2LC0450-1AF00-0AA0 0.1
135-6 125 7 0.0010 2LC0450-2AF00-0AA0 0.3
150-6 140 7 0.0013 2LC0450-3AF00-0AA0 0.4
176-6 165 9 0.0035 2LC0450-4AF00-0AA0 0.7
185-6 175 11 0.0053 2LC0450-5AF00-0AA0 0.9
212-6 195 10 0.0088 2LC0450-6AF00-0AA0 1.3
225-6 210 10 0.0145 2LC0450-7AF00-0AA0 1.8
256-6 240 12 0.0269 2LC0450-8AF00-0AA0 2.6
272-6 255 16 0.0425 2LC0451-0AF00-0AA0 3.7
298-6 280 20 0.0653 2LC0451-1AF00-0AA0 4.7
325-6 305 22 0.1081 2LC0451-2AF00-0AA0 6.6
Plate pack MCECM
64-4 58 6 0.0001 2LC0460-0AS00-0AA0 0.1
96-6 82 6 0.0002 2LC0460-1AS00-0AA0 0.1
120-6 106 7 0.0006 2LC0460-2AS00-0AA0 0.3
142-6 128 9 0.0018 2LC0460-3AS00-0AA0 0.6
162-6 147 11 0.0033 2LC0460-4AS00-0AA0 0.9
190-6 168 10 0.0060 2LC0460-5AS00-0AA0 1.2
214-6 194 10 0.0116 2LC0460-6AS00-0AA0 1.8
230-6 210 12 0.0189 2LC0460-7AS00-0AA0 2.5
245-6 224 16 0.0299 2LC0460-8AS00-0AA0 3.5
275-6 251 20 0.0487 2LC0461-0AS00-0AA0 4.6
310-6 285 22 0.0891 2LC0461-1AS00-0AA0 6.5
345-6 314 24 0.1461 2LC0461-2AS00-0AA0 8.7
Ordering example for plate pack NAN: Ordering example for plate pack MCECM:
ARPEX ARP-6 plate pack, size 115-6, complete with screw ARPEX ARP-6 plate pack, size 120-6, complete with screw
connection. connection.
Article No.: Article No.:
2LC0450-1AF00-0AA0 LC0460-2AS00-0AA0
1)
Protected by patent in a number of countries on the date of creation of this catalog.
Siemens MD 10.1 · 2015 6/45

© Siemens AG 2015

Torsionally Rigid All-Steel Couplings — ARPEX ARW-4/-6 Series
General information
■ Overview

■ Benefits
6
ARPEX couplings of the ARW-4/-6 series are outstanding for to be compensated for by the coupling are to be expected. The
their large angular misalignment capacity of 3°. They were spe- intermediate spacer lengths are variable and are manufactured
cially designed for drives where high misalignments which have to customer specifications.
■ Application
ARPEX couplings of the ARW-4/-6 series are used where large Main areas of application for the ARW-4/-6 series:
misalignment capacities are required. In the paper-making ma- • Paper-making machines
chine industry, the ARW coupling has already proved itself as a
maintenance-free alternative to the cardan shaft. Torques of be- • Wind power systems
tween 92 and 80000 Nm can be transmitted at a permitted an- • Traction drives
gular misalignment of 3.0°. The intermediate spacer can be fit-
ted radially without moving the connected units.
■ Design
The design of an ARPEX NHN coupling of the ARW-4/-6 series is size 647-4 plate packs in rectangular design, from size 695-6 in
shown in the following illustration. The plate packs are bolted al- hexagonal design are used. The intermediate spacers are vari-
ternately between the flanges of the coupling hubs and the inter- able in length and are manufactured specifically to customer
mediate spacer. Up to size 292-4 close-fitting bolts and from size specifications.
324-4 conical screw connections are used for fastening. Up to
Plate pack
Hub
Intermediate spacer
Close-fitting bolt
Collar nut G_MD10_EN_00163a
Variants of the ARPEX coupling, ARW-4/-6 series
6/46 Siemens MD 10.1 · 2015

© Siemens AG 2015

General information
Variants of the ARPEX coupling, ARW-4/-6 series
Types
NHN Variant with unmachined intermediate spacer, with
variable spacer length Dimension sheets and further information are available on request.
The coupling parts of the ARPEX ARW-4/-6 series with the
exception of H spacers are machined on all sides. These are
delivered with unmachined, primed spacer tube.
■ Technical data
Power ratings, type NHN
Size Rated Maximum Overload Fatigue Maximum Maximum permitted shaft misalignment Torsional
torque torque torque torque speed stiffness
TKN TKmax TKOL TKW nKmax +ΔKa –ΔKa ±ΔKw ±ΔKr CTdyn
Tension Compression for for
S = 1000 mm S = 1000 mm
Nm Nm Nm Nm rpm mm mm mm MNm/rad
101-4 92 140 230 37 10400 2.4 2.0 3.0° 51.8 0.006
133-4 225 340 560 90 7850 3.3 2.2 51.7 0.012
167-4 450 680 1130 180 6250 4.2 2.2 51.6 0.028
196-4 800 1200 2000 320 5350 5.1 2.2 51.6 0.068
230-4 1250 1880 3200 500 4550 5.7 2.2 51.6 0.108
260-4 2000 3000 5000 800 4000 6.6 2.2 51.5 0.174
6
292-4 2700 4100 6800 1080 3550 7.5 2.8 51.4 0.275
324-4 3850 5800 9700 1540 3200 8.4 2.8 51.4 0.451
355-4 5250 7900 13200 2100 2950 9.0 2.8 51.4 0.622
389-4 6650 10000 16700 2660 2700 10.0 2.8 51.4 0.657
439-4 9850 15000 25000 3940 2350 11.1 3.0 51.3 1.08
499-4 13300 20000 34000 5320 2100 12.4 4.8 50.8 1.32
547-4 19000 29000 48000 7600 1900 13.4 4.8 50.7 2.03
600-4 25150 38000 63000 10060 1750 14.6 4.8 50.6 2.73
647-4 32500 49000 82000 13000 1600 16.0 4.8 50.6 3.93
695-6 41000 62000 103000 16400 1500 17.0 4.8 50.7 10.1
756-6 52000 78000 130000 20800 1350 18.0 4.8 50.6 14.0
817-6 65000 98000 163000 26000 1250 20.0 4.8 50.5 16.9
880-6 80000 120000 200000 32000 1150 22.0 4.8 50.5 21.2
The radial misalignment ΔKr applies to a type NHN coupling with The torsional stiffness values apply to the entire coupling with
a shaft distance S = 1000 mm. The radial misalignment ΔKr for shaft distance S = 1000 mm. The torsional stiffness of the plate
other shaft distances S is calculated as follows: packs applies to the rated coupling torque TKN. To determine the
ΔKr = (S – S1) ⋅ tan(ΔKw) torsional stiffness for a specific operating point, e.g. for calculat-
ing torsional vibration, the manufacturer must be consulted.
The permitted shaft misalignments ΔKa, ΔKr and ΔKw are maximum
values and must not occur at the same time (see following table). TKmax permitted only five times per hour.
Size Permitted angular misalignment ΔKw (tension +) Permitted angular misalignment ΔKw (compression –)
3.0° 1.5° 0.0° 3.0° 1.5° 0.0°
Permitted axial misalignment ΔKa in mm Permitted axial misalignment ΔKa in mm
101-4 0.8 1.6 2.4 0.8 1.6 2
133-4 1.1 2.2 3.3 1.1 2.2 2.2
167-4 1.4 2.8 4.2 1.4 2.2 2.2
196-4 1.7 3.4 5.1 1.7 2.2 2.2
230-4 1.9 3.8 5.7 1.9 2.2 2.2
260-4 2.2 4.4 6.6 2.2 2.2 2.2
292-4 2.5 5.0 7.5 2.5 2.8 2.8
324-4 2.8 5.6 8.4 2.8 2.8 2.8
355-4 3.0 6.0 9.0 2.8 2.8 2.8
389-4 3.3 6.7 10.0 2.8 2.8 2.8
439-4 3.7 7.4 11.1 3.0 3.0 3.0
499-4 4.1 8.3 12.4 4.1 4.8 4.8
547-4 4.5 8.9 13.4 4.4 4.8 4.8
600-4 4.9 9.7 14.6 4.8 4.8 4.8
647-4 5.3 10.7 16.0 4.8 4.8 4.8
695-6 5.6 11.4 17.0 4.8 4.8 4.8
756-6 6 12.1 18.0 4.8 4.8 4.8
817-6 6.7 13.4 20.0 4.8 4.8 4.8
880-6 7.3 14.8 22.0 4.8 4.8 4.8
Because of design specifications, the maximum possible axial
shaft misalignment with plate packs pulled apart (tension +) is
greater than with plate packs pressed together (compression –).
Siemens MD 10.1 · 2015 6/47

© Siemens AG 2015

Type NHN

Torsionally rigid type NHN coupling with high angular misalignment capacity up to 3° and radially freely dismountable intermediate
spacer and variable shaft distance S.
NL1 S NL2
S1 LZ
G_MD10_XX_00164a
SZ
ØND1
ØND2
ØDZ
ØDA
ØD1
ØD2
6
N H N

torque mum Shaft moment of Order codes for bore
speed distance inertia diameters and tolerances
DA TKN nKmax
D1/D2 ND1/ DZ SZ NL1/ S1 LZ S J are specified in catalog m
ND2 NL2 section 3
Keyway min. min.
DIN 6885
101-4 92 10400 32 45 45 2.9 32 11 43 65 0.002 2LC0530-0AD ■ ■ -0AZ0 1.5
133-4 225 7850 45 60 48 2.9 45 13 59 85 0.008 2LC0530-1AD ■ ■ -0AZ0 3.9
167-4 450 6250 50 70 64 4.0 50 15 70 100 0.022 2LC0530-2AD ■ ■ -0AZ0 7.1
196-4 800 5350 60 80 89 4.0 60 16 83 115 0.056 2LC0530-3AD ■ ■ -0AZ0 12.1
230-4 1250 4550 75 100 102 5.0 75 16 83 115 0.109 2LC0530-4AD ■ ■ -0AZ0 17.9
260-4 2000 4000 90 120 133 5.0 90 17 96 130 0.189 2LC0530-5AD ■ ■ -0AZ0 24.6
292-4 2700 3550 100 130 152 5.0 100 19 92 130 0.359 2LC0530-6AD ■ ■ -0AZ0 35.1
324-4 3850 3200 110 145 168 6.3 110 20 120 160 0.520 2LC0530-7AD ■ ■ -0AZ0 43.7
355-4 5250 2950 120 160 178 7.1 120 20 125 165 0.856 2LC0530-8AD ■ ■ -0AZ0 59.8
389-4 6650 2700 130 175 194 7.1 130 20 130 170 1.09 2LC0531-0AD ■ ■ -0AZ0 68.9
439-4 9850 2350 150 200 219 7.1 150 22 166 210 2.23 2LC0531-1AD ■ ■ -0AZ0 106
499-4 13300 2100 165 220 245 7.1 165 30 170 230 3.81 2LC0531-2AD ■ ■ -0AZ0 142
547-4 19000 1900 190 250 299 8.8 190 32 176 240 6.24 2LC0531-3AD ■ ■ -0AZ0 191
600-4 25150 1750 205 275 324 8.8 205 34 182 250 10.2 2LC0531-4AD ■ ■ -0AZ0 257
647-4 32500 1600 225 300 343 10.0 225 35 220 290 16.5 2LC0531-5AD ■ ■ -0AZ0 348
695-6 41000 1500 240 325 368 10.0 240 33 224 290 23.7 2LC0540-0AD ■ ■ -0AZ0 441
756-6 52000 1350 255 340 394 12.5 255 34 232 300 33.2 2LC0540-1AD ■ ■ -0AZ0 525
817-6 65000 1250 270 360 406 12.5 270 36 238 310 49.1 2LC0540-2AD ■ ■ -0AZ0 659
880-6 80000 1150 300 400 419 12.5 300 37 256 330 72.8 2LC0540-3AD ■ ■ -0AZ0 849
The permitted length of the intermediate spacer depends on the Mass moments of inertia and weights apply to the entire NHN
maximum operating speed of the coupling (see following table). coupling with maximum bores D1/D2 and a shaft distance
S = S min.
6/48 Siemens MD 10.1 · 2015

© Siemens AG 2015

Type NHN
Size Speed nN
rpm
500 600 700 800 900 1000 1200 1400 1500 2000 2500 3000 4000
mm
101-4 2822 2577 2387 2233 2106 1999 1825 1691 1634 1416 1268 1159 1005
133-4 2949 2693 2494 2334 2201 2089 1908 1767 1708 1481 1326 1212 1051
167-4 3376 3083 2856 2672 2520 2392 2185 2024 1956 1696 1518 1387 1203
196-4 4029 3679 3407 3188 3007 2854 2606 2414 2333 2022 1811 1654 1435
230-4 4297 3924 3634 3400 3207 3043 2779 2574 2488 2156 1930 1764 1530
260-4 4943 4514 4181 3912 3689 3500 3197 2961 2861 2480 2220 2028 1759
292-4 5305 4844 4487 4198 3959 3757 3431 3178 3071 2662 2383 2177
324-4 5562 5079 4704 4401 4151 3939 3597 3332 3220 2791 2499 2283
355-4 5709 5214 4828 4518 4261 4043 3692 3420 3305 2865 2564
389-4 5968 5450 5047 4722 4453 4226 3859 3575 3454 2994 2680
439-4 6361 5809 5380 5034 4747 4505 4114 3811 3682 3192
499-4 6738 6154 5699 5333 5030 4773 4360 4039 3903 3384
547-4 7442 6797 6295 5890 5555 5272 4815 4460 4310
600-4 7762 7089 6565 6144 5794 5499 5022 4652 4496
647-4 7980 7287 6750 6316 5957 5653 5163 4783 4622 Outside the permitted speed range
695-6 8000 7553 6995 6545 6173 5858 5350 4956 4789
6
756-6 8000 7797 7221 6757 6372 6047 5523
817-6 8000 7920 7335 6864 6473 6143 5611
880-6 8000 8000 7456 6977 6580 6244
Ordering example:
ARPEX ARW-4 NHN coupling, size 133-4, with shaft distance
S = 1000 mm,
Article No.:
2LC0530-1AD99-0AZ0-Z
L0W+M1A+Q0Y+M13
Siemens MD 10.1 · 2015 6/49

© Siemens AG 2015

Plate pack ARW-4/-6

S1
S1
Figure 1 Figure 2
ØDA
ØDA
6
G_MD10_EN_00165
Plate packs of the ARW-4 series comprise ring plates (Fig. 1), those of the ARW-6 series side-bar plates (Fig. 2).
Size
DA S1 J m
kgm2 kg
101-4 11 0.0001 2LC0530-0AB00-0AA0 0.1
133-4 13 0.0005 2LC0530-1AB00-0AA0 0.2
167-4 15 0.0017 2LC0530-2AB00-0AA0 0.5
196-4 16 0.0037 2LC0530-3AB00-0AA0 0.7
230-4 16 0.0068 2LC0530-4AB00-0AA0 1.0
260-4 17 0.0136 2LC0530-5AB00-0AA0 1.5
292-4 19 0.0227 2LC0530-6AB00-0AA0 1.9
324-4 20 0.0288 2LC0530-7AB00-0AA0 2.1
355-4 20 0.0452 2LC0530-8AB00-0AA0 2.7
389-4 20 0.0645 2LC0531-0AB00-0AA0 3.2
439-4 22 0.1147 2LC0531-1AB00-0AA0 4.5
499-4 30 0.2235 2LC0531-2AB00-0AA0 6.9
547-4 32 0.3658 2LC0531-3AB00-0AA0 9.5
600-4 34 0.5355 2LC0531-4AB00-0AA0 11.4
647-4 35 0.7939 2LC0531-5AB00-0AA0 14.6
695-6 33 1.4624 2LC0540-0AB00-0AA0 24.6
756-6 34 1.2250 2LC0540-1AB00-0AA0 20.2
817-6 36 1.7497 2LC0540-2AB00-0AA0 23.9
880-6 37 2.5460 2LC0540-3AB00-0AA0 28.9
The plate pack of the ARW-4/-6 series is readily available as a Ordering example:
spare part. ARPEX ARW-4 plate pack, size 133-4,
complete with screw connection.
The plate pack is delivered with screw connection.
Article No.:
Up to size 292-4 close-fitting bolts with collar nuts, from size 2LC0530-1AB00-0AA0
324-4 patented 1) conical screw connections are used.
1)
this catalog.
6/50 Siemens MD 10.1 · 2015

© Siemens AG 2015

Torsionally Rigid All-Steel Couplings — ARPEX ARF-6 Series
General information
■ Overview

■ Benefits
6
ARPEX couplings of the ARF-6 series are extremely short and so key. The variant with slit clamping hubs enables the delivery of
suitable for drives with short shaft distances. They also serve as fully preassembled couplings. This means that the entire cou-
self-aligning couplings for axial, angular and radial misalign- pling can be dismounted and fitted without moving the con-
ment. The hubs are available both as pure clamping hubs for nected units.
smooth shafts and with parallel keyway for shafts with parallel
■ Application
ARPEX couplings of the ARF-6 series are designed for minimum hexagonal design. Torques of between 120 and 6100 Nm can
fitting spaces without having to sacrifice the advantages of the be transmitted at a permitted angular misalignment of 0.7°.
two-joint coupling. It is thus possible to compensate for both ax-
ial and angular as well as radial misalignment. By using half- Main areas of application for the ARF-6 series:
shell clamping hubs, the coupling can be radially freely dis- • Film stretching machines
mounted. Power is transmitted via hexagon socket head cap • Machines in the cellulose industry
screws and close-fitting bolts with nuts and ring plate packs in
• Machines in confined fitting situations
■ Design
The two plate packs form a unit with the adapter disk and are hexagon socket head cap screws at further three points. The
screwed together with close-fitting bolts and nuts at three points. hubs are designed as axially slit clamping hubs with a half-shell.
The alternate connection of this intermediate unit with the For larger bores these can be manufactured as jumbo hubs.
flanges of the split coupling hubs is achieved by means of short Optionally, the hubs are also available without parallel keyway.
Hexagon socket
head cap screw
Split hub
Hexagon socket
head cap screw
Plate pack unit
Hexagon socket head cap screw G_MD10_EN_00166a
Design of the ARPEX coupling, ARF series
Siemens MD 10.1 · 2015 6/51

© Siemens AG 2015

General information
Design of the ARF coupling
Types
GG Variant with 2 standard clamping hubs
Dimension sheets and further information are available on re-
GJ Variant with 1 jumbo clamping hub for large bore quest.
diameters
■ Technical data
Power ratings, types GG and GJ
Size Rated Maximum Overload Fatigue Maximum Maximum permitted shaft misalignment Torsional
torque torque torque torque speed stiffness
TKN TKmax TKOL TKW nKmax ±ΔKa ±ΔKw ±ΔKr CTdyn
Nm Nm Nm Nm rpm mm mm MNm/rad
84-6 120 220 330 55 12500 1.10 0.7° 0.16 0.07
111-6 190 350 520 90 9450 1.80 0.16 0.13
132-6 350 650 950 160 7950 2.02 0.20 0.20
147-6 500 900 1350 230 7100 2.40 0.20 0.28
171-6 900 1700 2450 400 6100 2.74 0.24 0.57
182-6 1450 2600 4000 650 5750 2.86 0.29 0.66
202-6 2150 3900 5800 980 5200 3.06 0.29 0.77
218-6 3200 5800 8700 1450 4800 3.14 0.37 1.25
252-6 4500 8100 12000 2000 4150 3.70 0.45 1.55
6
267-6 6100 11000 16500 2800 3900 3.84 0.46 1.80

mum values and must not occur at the same time (see following The torsional stiffness of the plate packs applies to the rated
table). coupling torque TKN. To determine the torsional stiffness for a
specific operating point, e.g. for calculating torsional vibration,
TKmax permitted only five times per hour. the manufacturer must be consulted.
0.0° 0.1° 0.2° 0.3° 0.4° 0.5° 0.6° 0.7°
84-6 1.10 0.94 0.79 0.63 0.47 0.31 0.16 0.00
111-6 1.80 1.54 1.29 1.03 0.77 0.51 0.26 0.00
132-6 2.02 1.73 1.44 1.15 0.87 0.58 0.29 0.00
147-6 2.40 2.06 1.71 1.37 1.03 0.69 0.34 0.00
171-6 2.74 2.35 1.96 1.57 1.17 0.78 0.39 0.00
182-6 2.86 2.45 2.04 1.63 1.23 0.82 0.41 0.00
202-6 3.06 2.62 2.19 1.75 1.31 0.87 0.44 0.00
218-6 3.14 2.69 2.24 1.79 1.35 0.90 0.45 0.00
252-6 3.70 3.17 2.64 2.11 1.59 1.06 0.53 0.00
267-6 3.84 3.29 2.74 2.19 1.65 1.10 0.55 0.00
6/52 Siemens MD 10.1 · 2015

© Siemens AG 2015

Types GG and GJ

Radially freely dismountable, torsionally rigid coupling, available as types GG and GJ.
Complete dismounting without moving the units with extremely short shaft distances.
LG
NL1 NL2
S1
Smax
ØND1
ØND2
ØDA
ØD1
ØD2
Smin
G G
G_MD10_XX_00167
ØDA=ØND2
Smax
ØND1
ØD1
ØD2
6
Smin
G J
The shaft tolerance must be specified in the order. To specify, "-Z" must be added to the article number and the order codes
"Y26" and "Y27" with plain text specification of the shaft tolerance for D1 and D2 must be added as well.
Size Rated Maxi- Type Dimensions in mm Mass moment Article No. Weight
torque mum Shaft distance of inertia Order codes for bore
speed diameters and toler-
DA TKN nKmax D1 D2 ND1 ND2 NL1/ S1 S LG J ances are specified in m
Keyway DIN 6885 NL2 catalog section 3
max. max. min. max.
Parallel Paral- Clamp-
mm Nm rpm key/ lel ing kgm2 kg
clamping key seat
seat
84-6 120 12500 GG 25 25 25 50 50 40 6 16 39 99 0.0013 2LC0420-0AB99-0AA0 1.7
GJ 40 48 84 0.0021 2LC0420-0AC99-0AA0 2.1
111-6 190 9450 GG 48 48 48 76 76 40 6 16 39 99 0.0043 2LC0420-1AB99-0AA0 2.9
GJ 65 65 111 0.0067 2LC0420-1AC99-0AA0 3.6
132-6 350 7950 GG 52 52 52 90 90 55 8 18.5 45 134 0.0110 2LC0420-2AB99-0AA0 5.7
GJ 75 80 132 0.0177 2LC0420-2AC99-0AA0 7.0
147-6 500 7100 GG 60 60 60 105 105 65 8 18.5 45 154 0.0199 2LC0420-3AB99-0AA0 8.3
GJ 85 85 147 0.0324 2LC0420-3AC99-0AA0 10.4
171-6 900 6100 GG 70 70 70 122 122 75 9 22.5 56 179 0.0439 2LC0420-4AB99-0AA0 13.3
GJ 100 100 171 0.0695 2LC0420-4AC99-0AA0 16.4
182-6 1450 5750 GG 70 70 70 126 126 85 11 29 71 205 0.0649 2LC0420-5AB99-0AA0 17.5
GJ 100 110 182 0.1005 2LC0420-5AC99-0AA0 20.9
202-6 2150 5200 GG 75 75 75 138 138 85 11 29 71 205 0.0986 2LC0420-6AB99-0AA0 21.9
GJ 115 125 202 0.1519 2LC0420-6AC99-0AA0 25.6
218-6 3200 4800 GG 90 90 90 149 149 95 14 35 86 234 0.1499 2LC0420-7AB99-0AA0 27.2
GJ 130 130 218 0.2345 2LC0420-7AC99-0AA0 33.6
252-6 4500 4150 GG 100 100 100 166 166 105 17 40.5 101 264 0.2924 2LC0420-8AB99-0AA0 39.9
GJ 140 150 252 0.4651 2LC0420-8AC99-0AA0 49.8
267-6 6100 3900 GG 110 110 100 177 177 110 17 40.5 102 275 0.3827 2LC0421-0AB99-0AA0 45.9
GJ 150 160 267 0.6129 2LC0421-0AC99-0AA0 58.1
Jumbo hubs for larger shaft diameters. Ordering example:
G and J hubs in split clamping hub variant. ARPEX ARF-6 GG coupling, size 132-6, for shaft diameter
The hub variant with keyway rates as standard. Optionally, the ∅D1 45h6 mm, without keyway, for shaft diameter ∅D2
shaft/hub connection can be implemented without keyway as a 50k6 mm, with keyway to DIN 6885-1, keyway width P9.
pure clamping seat. Article No.: 2LC0420-2AB99-0AA0-Z
For specification of plate pack, see under spare parts. L1A+M1C+L45+Y26+Y27
Weights and mass moments of inertia apply to the entire Plain text to Y26: h6
coupling with maximum bores D1/D2. Plain text to Y27: k6
Siemens MD 10.1 · 2015 6/53

© Siemens AG 2015

Plate pack ARF-6
S
S1
Figure 1
ØDA
6
G_MD10_EN_00168
Ring plates (Fig. 1) are used for the plate packs.

Size Type
DA S S1 J m
kgm2 kg
84-6 GG 19 6 0.0003 2LC0420-0AE00-0AA0 0.30
GJ 2LC0420-0AH00-0AA0
111-6 GG 19 6 0.0009 2LC0420-1AE00-0AA0 0.46
GJ 2LC0420-1AH00-0AA0
132-6 GG 24 8 0.0026 2LC0420-2AE00-0AA0 0.90
GJ 2LC0420-2AH00-0AA0
147-6 GG 24 8 0.0038 2LC0420-3AE00-0AA0 1.07
GJ 2LC0420-3AH00-0AA0
171-6 GG 29 9 0.0097 2LC0420-4AE00-0AA0 1.96
GJ 2LC0420-4AH00-0AA0
182-6 GG 35 11 0.0143 2LC0420-5AE00-0AA0 2.58
GJ 2LC0420-5AH00-0AA0
202-6 GG 35 11 0.0240 2LC0420-6AE00-0AA0 3.53
GJ 2LC0420-6AH00-0AA0
218-6 GG 44 14 0.0383 2LC0420-7AE00-0AA0 4.89
GJ 2LC0420-7AH00-0AA0
252-6 GG 54 17 0.0812 2LC0420-8AE00-0AA0 7.90
GJ 2LC0420-8AH00-0AA0
267-6 GG 55 17 0.1152 2LC0421-0AE00-0AA0 9.60
GJ 2LC0421-0AH00-0AA0
The plate pack unit for the ARF-6 series is readily available as a
spare part in most sizes.
The plate pack unit comprises two preassembled plate packs
with adapter disk, including screw connection.
The standard screw connection comprises hexagon socket
head cap screws and close-fitting bolts with nuts.
6/54 Siemens MD 10.1 · 2015

Flender ARPEX Couplings PDF

Uploaded by

Copyright:

Available Formats

Flender ARPEX Couplings PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Flender ARPEX Couplings PDF

Uploaded by

Copyright:

Available Formats

6

6/2 ARPEX Series - General information 6/37 ARPEX ARP-6 Series

Siemens MD 10.1 · 2015

FLENDER Standard Couplings

Coupling suitable for use in potentially explosive

II 2D T 120 °C -40 °C ≤ Ta ≤ +70 °C

and compensate for shaft misalignments, while generating only

6/2 Siemens MD 10.1 · 2015

FLENDER Standard Couplings

Patented1) conical screw connection

1) Protected by patent in a number of countries on the date of creation of this catalog.

A further feature of the conical screw connection is the genuine

Siemens MD 10.1 · 2015 6/3

FLENDER Standard Couplings

Coupling suitable for use in potentially explosive

ARPEX couplings of the ARS-6 series are outstanding for their

6/4 Siemens MD 10.1 · 2015

FLENDER Standard Couplings

Design of an ARPEX coupling, ARS-6 series, type NEN

Siemens MD 10.1 · 2015 6/5

FLENDER Standard Couplings

6/6 Siemens MD 10.1 · 2015

FLENDER Standard Couplings

Siemens MD 10.1 · 2015 6/7

FLENDER Standard Couplings

■ Selection and ordering data

Size Rated Maxi- Type Dimensions in mm Mass Article No. Weight

6/8 Siemens MD 10.1 · 2015

FLENDER Standard Couplings

Siemens MD 10.1 · 2015 6/9

FLENDER Standard Couplings

■ Selection and ordering data

Size Rated Maxi- Type Dimensions in mm Mass Article No. Weight

6/10 Siemens MD 10.1 · 2015

FLENDER Standard Couplings

Siemens MD 10.1 · 2015 6/11

FLENDER Standard Couplings

■ Selection and ordering data

Size Rated Maxi- Type Dimensions in mm Mass Article No. Weight

6/12 Siemens MD 10.1 · 2015

FLENDER Standard Couplings

Siemens MD 10.1 · 2015 6/13

FLENDER Standard Couplings

■ Selection and ordering data

Size Rated Maximum Dimensions in mm Mass Article No. Weight

6/14 Siemens MD 10.1 · 2015

FLENDER Standard Couplings

Siemens MD 10.1 · 2015 6/15

FLENDER Standard Couplings

■ Selection and ordering data

Size Rated Maximum Dimensions in mm Mass Article No. Weight

6/16 Siemens MD 10.1 · 2015

FLENDER Standard Couplings

Siemens MD 10.1 · 2015 6/17

FLENDER Standard Couplings

■ Selection and ordering data

Variant ZW with intermediate shaft

Size Rated Maximum Type Dimensions in mm Mass Article No. Weight

6/18 Siemens MD 10.1 · 2015