DOMINO

The lightweight panel formwork for

building construction and civil engineering

Product Brochure – Issue 01/2015

 Inhalt

System Advantages Standard Applications

4 DOMINO 12 DOMINO
The lightweight panel form- standard applications
work for building construction Corners, T-junctions and fillers
and civil engineering can easily be realised within
6 Lightweight the system
Low dead weight and only 5
panel widths
9 Simple
One component for virtually
all connections – the Alignment
Coupler DRS
10 Practical
Inset tie points and a compre-
hensive range of accessories
for fast working operations in
all situations

Edition 01/2015

Publisher

PERI GmbH
Formwork Scaffolding Engineering
Rudolf-Diesel-Strasse 19
89264 Weissenhorn
Germany
[email protected]
www.peri.com

2
Important notes

All current safety regulations and guidelines shown in these detailed descriptions must
­applicable in those countries where our products ­nevertheless be available. The systems or items
are used must be observed. shown might not be available in every country.

The photos shown in this brochure feature const- Safety instructions and load specifications are
ruction sites in progress. For this reason, safety to be strictly observed at all times. Separate
and anchor details in particular cannot always be structural calculations are required for any
considered conclusive or final. These are subject ­deviations from the standard design data.
to the risk assessment carried out by the contractor.
The information contained herein is subject to
In addition, the computer graphics used are to be technical changes in the interests of progress.
regarded as system representations. To facilitate ­Errors and typographical mistakes reserved.
understanding, these and the detailed illustrations
shown have been partially reduced to certain
­aspects. The safety installations that are not

3
System Advantages

DOMINO
The lightweight panel formwork for
building construction and civil engineering

With the DOMINO panel formwork, All DOMINO system components can easily
PERI has a robust and lightweight be moved into position without the use of a
wall formwork in its programme crane. The lightweight formwork is ideally
which is ideal for building construc- suited for forming:
tion and civil engineering projects.
■ foundations
With the appropriate frame, corner and ■ basement and storey-level walls
stopend panels as well as compensa- ■ beams
tions, a wide range of applications can ■ swimming and adventure pools
be realised in the system. ■ rectangular piers and columns
■ parapets and retaining walls
The supplementary scaffold bracket is ■ supply shafts and small traffic tunnels
used to create safe working platforms. ■ refurbishment projects
DOMINO frames are made of steel or
aluminium.

4
 System Advantages

■ Lightweight ■ Simple ■ Practical

Low dead weight, only 5 panel One component for virtually all Inset tie points and a compre-
widths, also available with connections – the Alignment hensive range of accessories for
­aluminum frames Coupler DRS fast working operations in all si-
tuations

Proven high quality

For the production of the panel form-
work, PERI places great importance
on the highest possible resistance to
mechanical stress and long service life
of the components.

In the company's state-of-the-art

­powder coating plant, PERI achieves
highly scratch-resistant, durable pain-
ted surfaces of the formwork frames.
All elements are galvanized on the
­inside and have a closed frame profile.
The integrated corner castings provide
a high degree of rigidity of the form-
work elements.

Easy cleaning
The smooth surfaces and the closed
frame profile avoid concrete adhesion
to the greatest possible extent, and
also make it easier to clean the ele-
ments.

5
System Advantages

Lightweight
Low dead weight and only 5 panel widths

DOMINO is the lightweight panelized

formwork system with elements
made of steel or aluminium for buil-
ding construction and civil enginee-
ring projects. For easy distinction,
the steel and aluminium elements
are powder coated red and yellow
respectively.

The weight of the largest aluminum

­panel (250 cm x 100 cm) is less than
60 kg, and it can also be carried by two
workers without the use of a crane.

The selected DOMINO panel sizes are

best suited to the frequently used small-
scale applications.

However, the lightweight DOMINO

formwork elements also allow much
larger dimensions. For concreting
heights to 2.50, only two anchors are
required – that means 1.25 m² wall
­surface per tie.

Aluminium elements are yellow powder-coated.

As a result, they are easy to distinguish from the
steel elements.

6
 System Advantages

Width
100 75 50 35 25 DM 75 DISE DGE DAW
Multi-Purpose Internal Articulated Outside
Panel Steel Corner ­C orner ­ orner Angle
C
250

S) 87.700 kg S) 71.600 kg S) 54.500 kg S) 44.100 kg S) 37.700 kg S) 76.500 kg S) 66.000 kg A) 40.600 kg A) 10.500 kg

A) 59.500 kg A) 47.600 kg A) 50.200 kg
150
Height

S) 56.500 kg S) 46.100 kg S) 34.200 kg S) 26.900 kg S) 22.700 kg S) 51.300 kg S) 40.000 kg A) 23.700 kg A) 6.490 kg

125

S) 47.300 kg S) 38.700 kg S) 28.600 kg S) 22.400 kg S) 18.600 kg S) 43.700 kg S) 33.300 kg A) 21.300 kg A) 5.490 kg

A) 31.000 kg A) 24.800 kg A) 27.300 kg
75

S) 32.400 kg S) 26.600 kg S) 19.300 kg S) 14.500 kg S) 12.100 kg S) 31.600 kg S) 20.500 kg A) 14.200 kg A) 3.500 kg

With 5 perfectly matched widths Key

A) Aluminium
(25 cm, 35 cm, 50 cm, 75 cm and Panels with aluminium frames
100 cm) and 4 different standard element (yellow powder-coated)
heights (75 cm, 125 cm, 150 cm and
S) Steel
250 cm), a wide range of formworking Panels with steel frames
tasks can be accomplished. (red powder-coated)

7
8
 System Advantages

Simple
One component for virtually all connections –
the Alignment Coupler DRS

The Alignment Coupler DRS was

­designed specifically for the DOMINO
system and has three advantages:
the formwork elements are flush,
aligned and tight in a single opera­
tion. The extremely accurate align-
ment thus provides the very best
formwork results day after day.

The Alignment Coupler DRS is used for

standard panel joints, external and in-
ternal angles, acute and oblique angles,
stopend formwork, timber compensa-
tions and extensions.

The Alignment Coupler DRS on a standard panel joint ... ... and with timber compensations up to 10 cm thick.

Compensations with filler timber up to

10 cm are carried out with the Alignment
Coupler only.

For compensations up to 12 cm, the

supplementary Compensation Waler
DAR takes over the bracing, aligning
and force-transferring function.

Compensations up to 30 cm can be
­realised using the Filler Support DPA.
The Compensation Waler DAR 80
transfers the anchor forces to the
­adjacent panels.

Up to 12 cm with DOMINO Alignment Coupler Up to 30 cm with Filler Support DPA as well as

DRS and filler timber as well as 2 anchors in the 2 anchors in the Compensation Waler DAR 80.
Compensation Waler DAR 80.

DOMINO DKS Wedge Coupler

As an alternative, the Wedge Coupler
can be used for panel connections
­without high loads in the foundations
area.

9
System Advantages

Practical
Inset tie points and a comprehensive range of accessories
for fast working operations in all situations

The tie points are inset so that the

ties do not collide with water bars
or dense reinforcement. All cross
struts on the DOMINO panels have 1,50 m
1,25 m
connecting holes for the wide range
of available accessories.

0,75 m

0,75 m
Inset tie points result, DOMINO is extremely suitable
Thanks to the inset tie points, obstruc- for forming foundations. Due to the
tions can be avoided without any prob- ­inset tie points, the panels (125 cm,
lems. Thus, anchors positioned close 150 cm) can be used in both a vertical
to the ground are easy to install. As a and horizontal position.

DOMINO Lifting Hook

The Lifting Hook can carry up to 500 kg.
This allows the moving of large-sized
vertically positioned panels or panel
units. Always use 2 Lifting Hooks for
each unit being moved.

DOMINO Scaffold Bracket DOMINO Brace Connector DOMINO Stacking Device

The Scaffold Bracket DG 85 for assembling The Brace Connector DRA is used for con- For crane and forklift transport operations,
an 85 cm wide concreting scaffold. The necting push-pull props and kickers to hori- a min. 2 and max. 8 panels are stacked using
maximum bracket spacing is a cost-effective zontal and vertical struts. 4 stacking devices.
2.00 m with an imposed load of 150 kg/m².
Planking and guardrails are installed in
accordance with DIN 4420. The handrails
are erected using handrail posts HSGP.

10
 System Advantages

Foundation Tie Clamp and Top Tie

Bracket for strip foundations and
single footings
The DOMINO Foundation Tie Clamp for
easy shuttering of foundations, replacing
the bottom tie position as well as saving
work space and consequently earthmo-
ving operations. Ties are tensioned ac-
curately with a self-cleaning ­hexagonal
spindle.

Using the top tie bracket for the top tie

point avoids having to exactly position
the DOMINO panels opposite each
other. It is possible to tie at any position
of the panel.

Foundation Tie Clamp DLS Perforated Foundation Tie Top Tie Bracket DAH

High permissible concrete pressure

For concreting heights up to 2.50 m,
DOMINO withstands the full hydrostatic
pressure and conforms to DIN 18202,
Table 3 line 7 (steel panels) and line 6
(aluminium panels). For greater heights,
a fresh concrete pressure of 60 kN/m2
for steel panels is permissible in compli-
ance with DIN 18202, Table 3 Line 6.
This allows fast concreting and ensures
extremely flat concrete surfaces.

DOMINO formwork with push-pull

props and concreting scaffold ready
for use.

11
Standard Applications

DOMINO standard applications

Corners, T-junctions and fillers
can easily be realised within the system

Corners and T-junctions can be forming a right-angled corner. Angles i­ntermediate dimensions that are not
­realised with DOMINO system com- from 75° to 165° can be realised using covered by the DOMINO system can be
ponents. Here, too, the principle the articulated corner. accurately shuttered with longitudinal
­applies that all site-relevant situa- compensations.
tions can be accomplished using T-junctions can usually be formed with
as few additional components as one 75-sized panel and two Inside Tight, aligned and flush connections are
possible. Steel Corners or alternatively by means guaranteed using the Alignment Coupler
of two Articulated Corners. Together DRS for longer longitudinal compensa-
Two 50-sized panels, an Outside Corner with the Wall Thickness Compensator, tions in connection with Compensation
Angle and a 90° Inside Steel Corner are wall thicknesses of 15 cm to 35 cm are Walers.
all the elements that are required for possible in 5 cm increments. Other

Basic rules for right-angled corners Internal formwork

Inside Steel Corner DISE, adjusted to suit the wall thickness with Compensator
External formwork DWD or timber.
Panel D 50, Corner Angle DAW.
DAW DAW DAW DAW

50 50 50 50

DISE
DISE
DISE
DISE
50

50

50

50

DWD 5 DWD 5
DWD 10
DWD 5
2x DWD 5

20 24 30 35

Basic rules for T-Junctions

Internal formwork
External formwork Inside Steel Corner DISE, adjusted to suit the wall thickness with Compensator
Panel D 75. DWD or timber.
20 30 35
24

DISE DISE DISE DISE DISE DISE DISE DISE

25

25

25
25

75 75 75 75

DWD 5 DWD 5 DWD 5 DWD 5

12
 Standard Applications

75° – 165°

On the external corners, 2 Alignment On the internal corners and standard With the articulated corners, angles
Couplers DRS are required per side panel joints, 2 Alignment Couplers DRS from 75° to 165° can be achieved.
for heights of 2.50 m. are required for heights of 2.50 m.

DOMINO Stopend Panel

AT

AT/MTF with continuous reinforcement,

with or without water stops: MT

■ Time savings min. 40%

AT
■ No damage to the formlining

The rubber lip allows a continuous

reinforcement thickness of max. 16 mm.

AT

MTF

AT

13
The optimal System
for every Project and
every Requirement

Wall Formwork Column Formwork Slab Formwork

Climbing Systems Bridge Formwork Tunnel Formwork Shoring Systems

Construction Scaffold Facade Scaffold Industrial Scaffold Access

DE en 01 | 2020 1ma 790352 © PERI GmbH

Protection Scaffold Safety Systems System-Independent Services

­Accessories

PERI GmbH
Formwork Scaffolding Engineering
Rudolf-Diesel-Strasse 19
89264 Weissenhorn
Germany
Tel. +49 (0)7309.950-0
Fax +49 (0)7309.951-0
[email protected]
www.peri.com