R1131x SERIES: Low Voltage 300ma LDO REGULATOR

＊R1131Dxx2 (HSON-6) is the discontinued product. As of June in 2016.
R1131x SERIES
Low Voltage 300mA LDO REGULATOR

NO.EA-116-130530
OUTLINE
The R1131x Series are CMOS-based low voltage regulator ICs with output voltage range from 0.8V to 3.3V.
The minimum operating voltage is 1.4V. Each of these voltage regulator ICs consists of a voltage reference unit,
an error amplifier, resistors for setting output voltage, a current limit circuit, and a chip enable circuit.
To prevent the destruction by over current, current limit circuit is included. Standby mode realizes ultra small
consumption current.
The output voltage of these ICs is internally fixed with high accuracy. Since the packages for these ICs are
SOT-23-5, SON-6, and HSON-6, high density mounting of the ICs on boards is possible.
FEATURES
• Supply Current ..................................................Typ. 80μA (VOUT < 1.8V)
Typ. 60μA (VOUT ≥ 1.8V)
• Standby Mode ...................................................Typ. 0.1μA
• Dropout Voltage ................................................Typ. 0.48V(IOUT=300mA Output Voltage=1.0V Type)
Typ. 0.31V(IOUT=300mA Output Voltage=1.5V Type)
Typ. 0.23V(IOUT=300mA Output Voltage=3.0V Type)
• Ripple Rejection................................................Typ. 65dB(f=1kHz)
• Temperature-Drift Coefficient of Output Voltage........Typ. ±100ppm/°C
• Line Regulation .................................................Typ. 0.01%/V
• Output Voltage Accuracy...................................±2.0%
• Output Voltage Range.......................................0.8V to 3.3V (0.1V steps)
(For other voltages, please refer to MARK INFORMATIONS.)
• Input Voltage Range .........................................1.4V to 6.0V
• Packages .........................................................SOT-23-5, SON-6, HSON-6
• Built-in fold-back protection circuit ....................Typ. 50mA (Current at short mode)
• External Capacitors...........................................CIN=COUT=Tantalum 1.0μF (VOUT < 1.0V)
CIN=COUT=Ceramic 1.0μF (VOUT ≥ 1.0V)
APPLICATIONS
• Precision Voltage References.
• Power source for electrical appliances such as cameras, VCRs and hand-held communication equipment.
• Power source for battery-powered equipment.
1
R1131x
BLOCK DIAGRAM
R1131xxxxA R1131xxxxB
VDD VOUT VDD VOUT
Vref Vref
Current Limit Current Limit

CE GND CE GND
R1131xxxxD
VDD VOUT
Vref
Current Limit
CE GND
2
R1131x
SELECTION GUIDE
The output voltage, CE pin polarity, auto discharge function, package, etc. for the ICs can be selected at the
user’s request.
Product Name Package Quantity per Reel Pb Free Halogen Free

R1131Nxx1∗-TR-FE SOT-23-5 3,000 pcs Yes Yes
R1131Dxx1∗-TR-FE SON-6 3,000 pcs Yes Yes
R1131Dxx2∗-TR-FE HSON-6 3,000 pcs Yes Yes
xx : The output voltage can be designated in the range from 0.8V(08) to 3.3V(33) in 0.1V steps.
(For other voltages, please refer to MARK INFORMATIONS.)
∗ : CE pin polarity and auto discharge function at off state are options as follows.
(A) "L" active, without auto discharge function at off state
(B) "H" active, without auto discharge function at off state
(D) "H" active, with auto discharge function at off state
3
R1131x
PIN CONFIGURATIONS
z SOT-23-5 z SON-6 z HSON-6
Top View Bottom View

Top View Bottom View
5 4 6 5 4 4 5 6
6 5 4 4 5 6
∗ ∗
∗
(mark side)
∗ ∗
1 2 3 1 2 3 3 2 1
1 2 3 3 2 1
PIN DESCRIPTIONS
• SOT-23-5
Pin No Symbol Pin Description
1 VDD Input Pin
2 GND Ground Pin
3 CE or CE Chip Enable Pin
4 NC No Connection
5 VOUT Output pin
• SON-6, HSON-6
Pin No Symbol Pin Description
1 VDD Input Pin
2 NC No Connection
3 VOUT Output pin
4 NC No Connection
5 GND Ground Pin
6 CE or CE Chip Enable Pin
∗) Tab and tab suspension leads are GND level. (They are connected to the reverse side of this IC.)
The tab is better to be connected to the GND, but leaving it open is also acceptable.
The tab suspension leads do not be connect to other wires or land patterns.
4
R1131x
ABSOLUTE MAXIMUM RATINGS

Symbol Item Rating Unit
VIN Input Voltage 6.5 V
VCE Input Voltage( CE /CE Pin) −0.3 to 6.5 V
VOUT Output Voltage −0.3 to VIN+0.3 V
IOUT Output Current 350 mA
∗
Power Dissipation (SOT-23-5) 420
PD ∗ mW
Power Dissipation (SON-6) 500
∗
Power Dissipation (HSON-6) 900
Topt Operating Temperature Range −40 to 85 °C
Tstg Storage Temperature Range −55 to 125 °C
∗) For Power Dissipation please refer to PACKAGE INFORMATION.
ABSOLUTE MAXIMUM RATINGS

Electronic and mechanical stress momentarily exceeded absolute maximum ratings may cause the
permanent damages and may degrade the life time and safety for both device and system using the device
in the field.
The functional operation at or over these absolute maximum ratings is not assured.
5
R1131x
ELECTRICAL CHARACTERISTICS
• R1131xxxxA Topt=25°C
Symbol Item Conditions Min. Typ. Max. Unit

VIN= Set VOUT+1V VOUT >1.5V ×0.98 ×1.02 V
VOUT Output Voltage
1μA ≤ IOUT ≤ 30mA VOUT ≤ 1.5V −30 +30 mV
IOUT Output Current VIN −VOUT=1.0V 300 mA
ΔVOUT/ VIN=Set VOUT+1V,
Load Regulation 40 70 mV
ΔIOUT 1mA ≤ IOUT ≤ 300mA
VOUT=0.8V 620 850
VOUT=0.9V 550 780
VDIF Dropout Voltage IOUT=300mA 1.0V ≤ VOUT < 1.5V 480 700 mV
1.5V ≤ VOUT < 2.6V 310 450
2.6V ≤ VOUT ≤ 3.3V 230 350
VIN=Set VOUT+1V, VOUT < 1.8V 80 111 μA
ISS1 Supply Current
VIN=Set VOUT+1V, VOUT ≥ 1.8V 60 90 μA
Istandby Standby Current VIN=VCE=Set VOUT+1V 0.1 1.0 μA
IOUT=30mA
ΔVOUT/
Line Regulation VOUT+0.5V ≤ VIN ≤ 6.0V (VOUT > 0.9V) 0.01 0.15 %/V
ΔVIN
1.4V ≤ VIN ≤ 6.0V (VOUT ≤ 0.9V)
f=1kHz, Ripple 0.2Vp-p
RR Ripple Rejection 65 dB
VIN=Set VOUT+1V, IOUT=30mA
VIN Input Voltage 1.4 6.0 V
ΔVOUT/ Output Voltage IOUT=30mA ppm
±100
ΔTopt Temperature Coefficient −40°C ≤ Topt ≤ 85°C /°C
ISC Short Current Limit VOUT=0V 50 mA
RPU CE Pull-up Resistance 1.87 5.0 12.0 MΩ
VCEH CE Input Voltage “H” 1.0 6.0 V
VCEL CE Input Voltage “L” 0 0.3 V
en Output Noise BW=10Hz to 100kHz 30 μVrms
RECOMMENDED OPERATING CONDITIONS (ELECTRICAL CHARACTERISTICS)
All of electronic equipment should be designed that the mounted semiconductor devices operate within the
recommended operating conditions. The semiconductor devices cannot operate normally over the
recommended operating conditions, even if when they are used over such conditions by momentary
electronic noise or surge. And the semiconductor devices may receive serious damage when they continue
to operate over the recommended operating conditions.
6
R1131x
• R1131xxxxB/D Topt=25°C
Symbol Item Conditions Min. Typ. Max. Unit

VIN=Set VOUT+1V VOUT >1.5V ×0.98 ×1.02 V
VOUT Output Voltage
1μA ≤ IOUT ≤ 30mA VOUT ≤ 1.5V −30 +30 mV
IOUT Output Current VIN−VOUT=1.0V 300 mA
ΔVOUT/ VIN=Set VOUT+1V
Load Regulation 40 70 mV
ΔIOUT 1mA ≤ IOUT ≤ 300mA
VOUT=0.8V 620 850
VOUT=0.9V 550 780
VDIF Dropout Voltage IOUT=300mA 1.0V ≤ VOUT < 1.5V 480 700 mV
1.5V ≤ VOUT < 2.6V 310 450
2.6V ≤ VOUT ≤ 3.3V 230 350
VIN=Set VOUT+1V, VOUT < 1.8V 80 111 μA
ISS1 Supply Current
VIN=Set VOUT+1V, VOUT ≥ 1.8V 60 90 μA
Istandby Standby Current VIN=Set VOUT+1V, VCE=GND 0.1 1.0 μA
IOUT=30mA
ΔVOUT/
Line Regulation VOUT+0.5V ≤ VIN ≤ 6.0V(VOUT > 0.9V) 0.01 0.15 %/V
ΔVIN
1.4V ≤ VIN ≤ 6.0V(VOUT ≤ 0.9V)
f=1kHz, Ripple 0.2Vp-p
RR Ripple Rejection 65 dB
VIN=Set VOUT+1V, IOUT=30mA
VIN Input Voltage 1.4 6.0 V
ΔVOUT/ Output Voltage IOUT=30mA ppm
±100
ΔTopt Temperature Coefficient −40°C ≤ Topt ≤ 85°C /°C
ISC Short Current Limit VOUT=0V 50 mA
RPD CE Pull-down Resistance 1.87 5.0 12.0 MΩ
VCEH CE Input Voltage “H” 1.0 6.0 V
VCEL CE Input Voltage “L” 0 0.3 V
en Output Noise BW=10Hz to 100kHz 30 μVrms
Nch On Resistance for auto
RLOW VCE=0V 60 Ω
discharge (D version only)
RECOMMENDED OPERATING CONDITIONS (ELECTRICAL CHARACTERISTICS)
All of electronic equipment should be designed that the mounted semiconductor devices operate within the
recommended operating conditions. The semiconductor devices cannot operate normally over the
recommended operating conditions, even if when they are used over such conditions by momentary
electronic noise or surge. And the semiconductor devices may receive serious damage when they continue
to operate over the recommended operating conditions.
7
R1131x
TYPICAL APPLICATION
IN VDD OUT OUT

OUT OUT
R1131x
C1 Series C2
GND
CE ⋅ CE
<External Components examples>

C2 1.0μF CM05X5R105K06AB (Kyocera)
C2 1.0μF C1005JBOJ105K (TDK)
C2 1.0μF GRM155B30J105KE18B (Murata)
Output Capacitor; 1.0μF or more capacity ceramic Type

(If VOUT < 1.0V, Tantalum Type is recommended)
Input Capacitor, 1.0μF or more capacity ceramic Type
TECHNICAL NOTES
When using these ICs, consider the following points:
Phase Compensation
In these ICs, phase compensation is made for securing stable operation even if the load current is varied. For
this purpose, be sure to use a 1.0μF or more capacitor COUT with good frequency characteristics and ESR
(Equivalent Series Resistance).
(Note: If a tantalum capacitor is connected to the Output pin for phase compensation, if the ESR value of the
capacitor is too large, the operation might be unstable. Because of this, test these ICs with as same external
components as ones to be used on the PCB.)
Chip capacitor characteristics of Bias dependence and Temperature characteristics may vary depending on its
size, manufacturer, and part number.
PCB Layout
Make VDD and GND lines sufficient. If their impedance is high, pick-up the noise or unstable operation may
result. Connect a capacitor with as much as 1.0μF capacitor between VDD and GND pin as close as possible.
Set external components, especially the output capacitor, as close as possible to the ICs, and make wiring as
short as possible.
8
R1131x
TEST CIRCUIT
VDD OUT VDD OUT OUT

ISS
R1131x A R1131x
C1 Series C2 IOUT VOUT C1 Series C2
GND V GND
CE ⋅ CE CE ⋅ CE
∗ C1=C2= Tantalum1.0μF (VOUT<1.0V) ∗ C1=C2=Tantalum1.0μF (VOUT<1.0V)

C1=C2=Ceramic1.0μF (VOUT >
= 1.0V) C1=C2=Ceramic1.0μF (VOUT >
= 1.0V)
Standard Test Circuit Supply Current Test Circuit
Pulse VDD OUT VDD OUT

Generator
P.G R1131x R1131x
Series C2 C1 Series C2
IOUT
GND GND
IOUTa IOUTb
CE ⋅ CE CE ⋅ CE
∗ C2=Tantalum1.0μF (VOUT<1.0V) ∗ C1=C2=Tantalum1.0μF (VOUT<1.0V)

C2=Ceramic1.0μF (VOUT >
= 1.0V)
= 1.0V)
Ripple Rejection, Line Transient Response Load Transient Response Test Circuit
Test Circuit
VDD OUT
R1131x
C1 Series C2 IOUT
GND ∗ Input signal waveform
to CE pin is shown below.
Pulse
Generator Set VOUT
CE ⋅ CE +1.0V
0V
∗ C1=C2=Tantalum1.0μF (VOUT<1.0V)
= 1.0V)
Turn on Speed with CE pin Test Circuit
9
R1131x
TYPICAL CHARACTERISTICS
1) Output Voltage vs. Output Current
R1131x08xx R1131x15xx
1.0 1.6
0.9 1.4
VIN =2.8V
Output Voltage VOUT(V)

3.5V
0.8
1.2
0.7 2.5V
1.45V 1.0
0.6
0.5 0.8
2.0V
0.4 0.6
0.3 VIN =1.8V
0.4
0.2
0.1 0.2
0 0
0 100 200 300 400 500 600 0 100 200 300 400 500 600
Output Current lOUT(mA) Output Current lOUT(mA)
R1131x26xx R1131x33xx
3.5 3.5
3.0 3.0
4.6V 5.3V
2.5 2.5
4.3V
2.0 2.0
3.6V 3.8V
1.5 1.5
3.1V VIN =3.6V
VIN =2.9V
1.0 1.0
0.5 0.5
0 0
0 100 200 300 400 500 600 0 100 200 300 400 500 600
Output Current lOUT(mA) Output Current lOUT(mA)
2) Output Voltage vs. Input Voltage

R1131x08xx R1131x15xx
1.0 1.8
0.9 1.6
0.8 1.4
0.7
1.2
0.6
1.0 IOUT= 1mA
0.5
0.8 IOUT=30mA
0.4 IOUT= 1mA
0.3 IOUT=30mA 0.6 IOUT=50mA
0.2 IOUT=50mA 0.4
0.1 0.2
0 0
0 1 2 3 4 5 6 0 1 2 3 4 5 6
Input Voltage VIN(V) Input Voltage VIN(V)
10
R1131x
R1131x26xx R1131x33xx
3.5 4.0
3.0 3.5

3.0
2.5
2.5
2.0
IOUT= 1mA
2.0 IOUT= 1mA
1.5
IOUT=30mA 1.5
IOUT=30mA
1.0
IOUT=50mA 1.0
IOUT=50mA
0.5 0.5
0 0
0 1 2 3 4 5 6 0 1 2 3 4 5 6
3) Supply Current vs. Input Voltage

R1131x08xx R1131x15xx
100 90
90 80
Supply Current ISS(μA)
80 70
70 60
60
50
50
40
40
30
30
20 20
10 10
0 0
0 1 2 3 4 5 6 0 1 2 3 4 5 6
R1131x26xx R1131x33xx
90 90
80 80
70 70
60 60
50 50
40 40
30 30
20 20
10 10
0 0
0 1 2 3 4 5 6 0 1 2 3 4 5 6
11
R1131x
4) Output Voltage vs. Temperature

R1131x08xx R1131x15xx
0.84 1.53
0.83 1.52

0.82 1.51
0.81 1.50
0.80 1.49
0.79 1.48
0.78 1.47
0.77 1.46
-40 -25 0 25 50 75 85 -40 -25 0 25 50 75 85
Temperature Topt(°C) Temperature Topt(°C)
R1131x26xx R1131x33xx
2.64 3.37
2.63 3.35
2.62 3.33
2.61 3.31
2.60 3.29
2.59 3.27
2.58 3.25
2.57 3.23
-40 -25 0 25 50 75 85 -40 -25 0 25 50 75 85
5) Supply Current vs. Temperature

R1131x08xx R1131x15xx
110 80
100
70
90
80 60
70 50
60
40
50
40 30
30 20
20
10
10
0 0
-40 -25 0 25 50 75 85 -40 -25 0 25 50 75 85
12
R1131x
R1131x26xx R1131x33xx
80 80
70 70

60 60
50 50
40 40
30 30
20 20
10 10
0 0
-40 -25 0 25 50 75 85 -40 -25 0 25 50 75 85
6) Dropout Voltage vs. Output Current

R1131x08xx R1131x09xx
0.8 0.8
0.7 0.7 85°C
Dropout Voltage VDIF(V)
0.6 0.6 25°C

0.5 0.5 -40°C
0.4 0.4
0.3 85°C 0.3
0.2 25°C 0.2
0.1 -40°C 0.1
0 0
0 50 100 150 200 250 300 0 50 100 150 200 250 300
Output Current IOUT(mA) Output Current IOUT(mA)
R1131x10xx R1131x15xx
0.8 0.40
0.7 85°C 0.35 85°C
0.6 25°C 0.30 25°C

0.5 -40°C 0.25 -40°C
0.4 0.20
0.3 0.15
0.2 0.10
0.1 0.05
0 0
0 50 100 150 200 250 300 0 50 100 150 200 250 300
13
R1131x
R1131x26xx R1131x33xx
0.40 0.40
0.35 85°C 0.35 85°C

0.30 25°C 0.30 25°C

0.25 -40°C 0.25 -40°C
0.20 0.20
0.15 0.15
0.10 0.10
0.05 0.05
0 0
0 50 100 150 200 250 300 0 50 100 150 200 250 300
7) Dropout Voltage vs. Set Output Voltage (Topt=25°C)

R1131xxx1x
0.80
IOUT=10mA
0.70
30mA
0.60 50mA
100mA
0.50 200mA
0.40 300mA
0.30
0.20
0.10
0
0.5 1 1.5 2 2.5 3 3.5
Set Output Voltage VREG(V)
8) Ripple Rejection vs. Input Bias (Topt=25°C CIN=none, COUT=Ceramic 1.0μF Ripple 0.2VP-P)
R1131x26xx (IOUT=1mA) R1131x26xx (IOUT=30mA)
80 80
70 70
Ripple Rejection RR(dB)
60 60
50 50
40 40
30 f = 400Hz 30
f = 400Hz
f = 1kHz
20 20 f = 1kHz
f = 10kHz
f = 10kHz
10 f = 100kHz 10 f = 100kHz
0 0
2.6 2.7 2.8 2.9 3.0 3.1 3.2 2.6 2.7 2.8 2.9 3.0 3.1 3.2
14
R1131x
R1131x26xx (IOUT=50mA)
80
70
60
50
40
30
f = 400Hz
20 f = 1kHz
f = 10kHz
10 f = 100kHz
0
2.6 2.7 2.8 2.9 3.0 3.1 3.2
Input Voltage VIN(V)
9) Ripple Rejection vs. Frequency (CIN=none)

R1131x08xx R1131x08xx
VIN=1.8VDC+0.2Vp-p, VIN=1.8VDC+0.2Vp-p,
COUT=Tantalum 1.0μF COUT=Tantalum 2.2μF
100 100
90 90
80 80
70 70
60 60
50 50
40 IOUT = 1mA 40 IOUT = 1mA
30 30
IOUT = 30mA IOUT = 30mA
20 20
0 0
0.1 1 10 100 0.1 1 10 100
Frequency f(kHz) Frequency f(kHz)
R1131x10xx R1131x10xx
COUT=Ceramic 1.0μF COUT=Ceramic 2.2μF
100 100
90 90
80 80
70 70
60 60
50 50
30 30
20 20
0 0
0.1 1 10 100 0.1 1 10 100
15
R1131x
R1131x15xx R1131x15xx
100 100
90 90

80 80
70 70
60 60
50 50
30 30
20 20
0 0
0.1 1 10 100 0.1 1 10 100
R1131x26xx R1131x26xx
100 100
90 90
80 80
70 70
60 60
50 50
30 30
20 20
0 0
0.1 1 10 100 0.1 1 10 100
R1131x33xx R1131x33xx
100 100
90 90
80 80
70 70
60 60
50 50
30 30
20 20
0 0
0.1 1 10 100 0.1 1 10 100
16
R1131x
10) Input Transient Response (CIN=none, tr=tf=5μs)

R1131x08xx R1131x10x
IOUT=30mA, IOUT=30mA,
COUT=Tantalum 1.0μF COUT=Ceramic 1.0μF
4 4
3 3


Input Voltage Input Voltage
2 2
0.82 1 1.02 1
0.80 1.00
Output Voltage Output Voltage
0.78 0.98
0.76 0.96
0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100
Time t(μs) Time t(μs)
R1131x26xx
IOUT=30mA,
COUT=Ceramic 1.0μF
5
Input Voltage 4
2.62
2.60
Output Voltage
2.58
2.56
0 10 20 30 40 50 60 70 80 90 100
Time t(μs)
11) Load Transient Response (tr=tf=0.5μs)
R1131x08xx R1131x08xx
VIN=1.8V CIN=Tantalum 1.0μF, VIN=1.8V CIN=Tantalum 1.0μF,
150 60
100 30
Output Current IOUT(mA)

Output Current Output Current

50 0
0.9 0 0.9
0.8 0.8
0.7 0.7
0.6 0.6
0 5 10 15 20 25 30 35 40 0 5 10 15 20 25 30 35 40
17
R1131x
R1131x10xx R1131x10xx
VIN=2.0V CIN=Ceramic 1.0μF, VIN=2.0V CIN=Ceramic 1.0μF,
150 150
100

100

50 50
1.1 0 1.1 0
1.0 1.0
0.9 0.9
0.8 0.8
0 5 10 15 20 25 30 35 40 0 5 10 15 20 25 30 35 40
R1131x10xx R1131x10xx
60 60
30 30



0 0
1.1 1.1
1.0 1.0
0.9 0.9
0.8 0.8
0 5 10 15 20 25 30 35 40 0 5 10 15 20 25 30 35 40
R1131x26xx R1131x26xx
150 150
100 100


50 50
2.7 0 2.7 0
2.6 2.6
2.5 2.5
2.4 2.4
0 5 10 15 20 25 30 35 40 0 5 10 15 20 25 30 35 40
18
R1131x
R1131x26xx R1131x26xx
60 60
30 30



0 0
2.7 2.7
2.6 2.6
2.5 2.5
2.4 2.4
0 5 10 15 20 25 30 35 40 0 5 10 15 20 25 30 35 40
12) Turn on speed with CE pin

R1131x08xx R1131x08xx
2.7 2.7
CE Input Voltage CE Input Voltage
1.8 1.8
CE Input Voltage VCE(V)

0V→1.8V 0V→1.8V
0.9 0.9
1.0 Output Voltage 0 1.0 Output Voltage 0
0.5 IOUT=0mA 0.5 IOUT=30mA
0 0
0 10 20 30 40 50 60 70 0 10 20 30 40 50 60 70
R1131x08xx R1131x33xx
VIN=1.8V CIN=Tantalum 1.0μF, VIN=4.3V CIN=Ceramic 1.0μF,
2.7 6
CE Input Voltage
CE Input Voltage 4
1.8 0V→4.3V

0V→1.8V 2
0.9 4
Output Voltage 0
1.0 Output Voltage 0 3
2 IOUT=0mA
0.5 IOUT=300mA
1
0
0
0 10 20 30 40 50 60 70 0 20 40 60 80 100 120 140

19
R1131x
R1131x33xx (ECO=H) R1131x33xx (ECO=L)

6 6
CE Input Voltage CE Input Voltage
4 4
0V→4.3V


0V→4.3V
2 2
4 0 4 Output Voltage 0
Output Voltage
3 3
IOUT=30mA IOUT=300mA
2 2
1 1
0 0
0 20 40 60 80 100 120 140 0 20 40 60 80 100 120 140

13) Turn-off Speed with CE

R1131x08xD R1131x08xD
2.4 2.4
1.8 1.8

1.2 1.2
CE Input Voltage
0.6 CE Input Voltage 0.6
1.8V→0V 1.8V→0V
1.0 0 1.0 0
0.5 Output Voltage 0.5 Output Voltage

IOUT=0mA IOUT=30mA
0 0
0 0.2 0.4 0.6 0.8 1.0 1.2 0 0.2 0.4 0.6 0.8 1.0 1.2
Time t(ms) Time t(ms)
R1131x08xD R1131x33xD
VIN=1.8V CIN=Tantalum 1.0μF, VIN=4.3V CIN=Ceramic 1.0μF,
2.4 5
4
1.8

3
1.2 CE Input Voltage 2
CE Input Voltage 0.6 4.3V→0V 1
1.8V→0V 4 0
1.0 0 3
0.5 Output Voltage 2 Output Voltage
IOUT=300mA 1 IOUT=0mA
0
0
0 0.2 0.4 0.6 0.8 1.0 1.2 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
20
R1131x
R1131x33xD R1131x33xD
5 5
4 4


3 3
CE Input Voltage 2 CE Input Voltage 2
4.3V→0V 1 4.3V→0V 1
4 0 4 0
3 3
2 Output Voltage 2 Output Voltage
1 IOUT=30mA 1 IOUT=300mA
0 0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
21
R1131x
ESR vs. Output Current

When using these ICs, consider the following points:
In these ICs, phase compensation is made for securing stable operation even if the load current is varied. For
this purpose, be sure to use a capacitor COUT with good frequency characteristics and ESR (Equivalent Series
Resistance) of which is in the range described as follows:
The relations between IOUT (Output Current) and ESR of Output Capacitor are shown below.
The conditions when the white noise level is under 40μV(Avg.) are marked as the hatched area in the graph.
<Test conditions>
(1) Frequency band: 10Hz to 2MHz
(2) Temperature: 25°C
R1131x08xx R1131x10xx
VIN=1.4V to 6.0V, VIN=1.4V to 6.0V,
CIN=Ceramic 1.0VμF COUT=Ceramic 1.0μF CIN=Ceramic 1.0VμF COUT=Ceramic 1.0μF
100 100
10 10
ESR (Ω)
ESR (Ω)
1 1
0.1 0.1
0.01 0.01
0 50 100 150 200 250 300 0 50 100 150 200 250 300
Output Current lOUT (mA) Output Current lOUT (mA)
R1131x26xx R1131x15xx
VIN=3.0V to 6.0V, VIN=2.0V to 6.0V,
CIN=Ceramic 1.0VμF COUT=Ceramic 1.0μF CIN=Ceramic 1.0VμF COUT=Ceramic 1.0μF
100 100
10 10
ESR (Ω)
ESR (Ω)
1 1
0.1 0.1
0.01 0.01
0 50 100 150 200 250 300 0 50 100 150 200 250 300
Output Current lOUT (mA) Output Current lOUT (mA)
22
R1131x
R1131x33xx
VIN=3.6V to 6.0V,
CIN=Ceramic 1.0VμF COUT=Ceramic 1.0μF
100
10
ESR (Ω)
0.1
0.01
0 50 100 150 200 250 300
Output Current lOUT (mA)
23
1. The products and the product specifications described in this document are subject to change or discontinuation of
production without notice for reasons such as improvement. Therefore, before deciding to use the products, please refer
to our sales representatives for the latest information thereon.
2. The materials in this document may not be copied or otherwise reproduced in whole or in part without prior written
consent of our company.
3. Please be sure to take any necessary formalities under relevant laws or regulations before exporting or otherwise
taking out of your country the products or the technical information described herein.
4. The technical information described in this document shows typical characteristics of and example application circuits
for the products. The release of such information is not to be construed as a warranty of or a grant of license under
our company's or any third party's intellectual property rights or any other rights.
5. The products listed in this document are intended and designed for use as general electronic components in standard
applications (office equipment, telecommunication equipment, measuring instruments, consumer electronic products,
amusement equipment etc.). Those customers intending to use a product in an application requiring extreme quality and
reliability, for example, in a highly specific application where the failure or misoperation of the product could result in
human injury or death (aircraft, spacevehicle, nuclear reactor control system, traffic control system, automotive and
transportation equipment, combustion equipment, safety devices, life support system etc.) should first contact us.
6. We are making our continuous effort to improve the quality and reliability of our products, but semiconductor products
are likely to fail with certain probability. In order to prevent any injury to persons or damages to property resulting from
such failure, customers should be careful enough to incorporate safety measures in their design, such as redundancy
feature, fire containment feature and fail-safe feature. We do not assume any liability or responsibility for any loss or
damage arising from misuse or inappropriate use of the products.
7. Anti-radiation design is not implemented in the products described in this document.
8. The X-ray exposure can influence functions and characteristics of the products. Confirm the product functions and
characteristics in the evaluation stage.
9. WLCSP products should be used in light shielded environments. The light exposure can influence functions and
characteristics of the products under operation or storage.
10. There can be variation in the marking when different AOI (Automated Optical Inspection) equipment is used. In the case
of recognizing the marking characteristic with AOI, please contact our sales or our distributor before attempting to use
AOI.
11. Please contact our sales representatives should you have any questions or comments concerning the products or
the technical information.
Official website
https://www.nisshinbo-microdevices.co.jp/en/
Purchase information
https://www.nisshinbo-microdevices.co.jp/en/buy/

R1131x SERIES: Low Voltage 300ma LDO REGULATOR

Uploaded by

Copyright:

Available Formats

R1131x SERIES: Low Voltage 300ma LDO REGULATOR

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

R1131x SERIES: Low Voltage 300ma LDO REGULATOR

Uploaded by

Copyright:

Available Formats

＊R1131Dxx2 (HSON-6) is the discontinued product. As of June in 2016.

Low Voltage 300mA LDO REGULATOR

VDD VOUT VDD VOUT

Current Limit Current Limit

Product Name Package Quantity per Reel Pb Free Halogen Free

Top View Bottom View

ABSOLUTE MAXIMUM RATINGS

ABSOLUTE MAXIMUM RATINGS

Symbol Item Conditions Min. Typ. Max. Unit

RECOMMENDED OPERATING CONDITIONS (ELECTRICAL CHARACTERISTICS)

Symbol Item Conditions Min. Typ. Max. Unit

RECOMMENDED OPERATING CONDITIONS (ELECTRICAL CHARACTERISTICS)

IN VDD OUT OUT

<External Components examples>

Output Capacitor; 1.0μF or more capacity ceramic Type

VDD OUT VDD OUT OUT

∗ C1=C2= Tantalum1.0μF (VOUT<1.0V) ∗ C1=C2=Tantalum1.0μF (VOUT<1.0V)

Standard Test Circuit Supply Current Test Circuit

Pulse VDD OUT VDD OUT

∗ C2=Tantalum1.0μF (VOUT<1.0V) ∗ C1=C2=Tantalum1.0μF (VOUT<1.0V)

Turn on Speed with CE pin Test Circuit

Output Voltage VOUT(V)

Output Voltage VOUT(V)

2) Output Voltage vs. Input Voltage

Output Voltage VOUT(V)

3) Supply Current vs. Input Voltage

Supply Current ISS(μA)

4) Output Voltage vs. Temperature

Output Voltage VOUT(V)

5) Supply Current vs. Temperature

Supply Current ISS(μA)

6) Dropout Voltage vs. Output Current

Dropout Voltage VDIF(V)

0.6 0.6 25°C

Dropout Voltage VDIF(V)

0.6 25°C 0.30 25°C

Dropout Voltage VDIF(V)

0.30 25°C 0.30 25°C

7) Dropout Voltage vs. Set Output Voltage (Topt=25°C)

9) Ripple Rejection vs. Frequency (CIN=none)

Ripple Rejection RR(dB)

Ripple Rejection RR(dB)

Ripple Rejection RR(dB)

10) Input Transient Response (CIN=none, tr=tf=5μs)

Output Voltage VOUT(V)

Input Voltage VIN(V)

Input Voltage VIN(V)

Output Current IOUT(mA)

Output Voltage VOUT(V)

Output Current Output Current

Output Current IOUT(mA)

Output Current IOUT(mA)

Output Current IOUT(mA)

Output Voltage VOUT(V)

Output Current Output Current

Output Current IOUT(mA)

Output Voltage VOUT(V)

Output Current Output Current

Output Current IOUT(mA)