METI GODERE HOTEL AND COMERCIAL BUILDING ELECTRICAL DESIGN MODIFICATION REQUEST

DO THE RIGHT THING @ THE RIGHT TIME!! [email protected]

METI GODERE HOTEL AND COMERCIAL BUILDING ELECTRICAL DESIGN MODIFICATION REQUEST

DO THE RIGHT THING @ THE RIGHT TIME!! [email protected]

METI GODERE HOTEL AND COMERCIAL BUILDING ELECTRICAL DESIGN MODIFICATION REQUEST

1. Introduction

This Technical Document is prepared to request approval letter and work order for the attached
cad design which last time we discussed with your Electrical Engineer, with this document, I have
tried to show a stable, safe able, economical and secure design to meet our last Technical
discussion. And new proposal for Telephone horizontal cabling with center distribution,
modification of multipurpose hall Electrical, Public address system and stage work with ceiling
design. The first 3 points 1.1 – 1.3 are approval requests, which we decided last time, point 1.2
just informing what I am going to follow for the implementation works, so I need fast response the
rest points which states under 1.5 is proposal of design modifications which needs series review
and approval

1.1. Power Distribution Network

Last time we agreed to split the power distribution network in two power lines which are one
Power line EEPCO + Diesel Generator for Hotel service and other side EEPCO line which
serves only for banks, and the output of each lines are connected with Energy proposed energy
meter for billing system and finally will be connected with bank ATS nearby There Distribution
boards as shown in figure 1a .

Figure 1a Proposed Power distribution network

DO THE RIGHT THING @ THE RIGHT TIME!! [email protected]

METI GODERE HOTEL AND COMERCIAL BUILDING ELECTRICAL DESIGN MODIFICATION REQUEST

Technically it is possible but due to safety such type of Installation is not recommended, as we
Know distribution board Main breakers output is connected on live base bar. And others breakers
feeds from these bar, so this makes a little bit complicated and unsafe for future maintenance, so
I propose to add one DB as main switch board as shown figure 1b

Figure 1b New Proposed Power distribution network

DO THE RIGHT THING @ THE RIGHT TIME!! [email protected]

METI GODERE HOTEL AND COMERCIAL BUILDING ELECTRICAL DESIGN MODIFICATION REQUEST

1.2. Data, Tele and TV line horizontal Networking

This Topic is prepared to provide a guide and detail description to the network infrastructure which
will be constructed for Palace In the implementation phase, all the hardware installation will follow
this document, and in the maintenance phase will give detail layout information for
troubleshooting. This document contain building, site work network design, Data center power
supply single line diagram and one clarification about Telecom/Data service point

1.2.1. Building Data Network and Riser diagram

Building Data layout diagram shows, single line wiring of the network from buildings access
switch to every floor access switch to every data points which the end user plugged the device
as shown on the design cad file

Hotel 3rd floor Hotel access UTP Cat 6

switch

Ground floor Cat 6

wall outlets for Wife
Hotel 2nd floor Hotel access switch UTP Cat 6
router for Hotel

Hotel 1st floor Hotel access switch UTP Cat 6

Hotel Main server Rack @

reception Data line from Service provider

Figure 1 Data lay out diagram

DO THE RIGHT THING @ THE RIGHT TIME!! [email protected]

METI GODERE HOTEL AND COMERCIAL BUILDING ELECTRICAL DESIGN MODIFICATION REQUEST

1.2.2. Building TV System Riser diagram

Building Data layout diagram shows, single line wiring of the network from buildings access
switch to every floor access switch to every data points which the end user plugged the device
as shown on the design cad file

Hotel 3rd floor Hotel TV/Sat Spliter TV outlets

TV/SAT @ 15
meter on roof

Hotel 2nd floor Hotel TV/sat Spliter TV outlets

TV outlets TV outlets

Hotel 1st floor Hotel TV/Sat Spliter Hotel 1st floor Hotel
TV/Sat Splitter

TV outlets For GF
TV Room @ Mirror side of ground
hotel @ Banks
reception

Figure 1 TV/Sat lay out diagram

1.2.3. Building Telephone Riser diagram

Previous Telephone system design is provided telephone line for every service for both
commercial and hotel parts of the building and the MDF was not clearly stated on the
design. as per the request of the design the technical teams are pulled for every service
room, but when we see the building service it was un necessary for banks and shops, any
ways ones it happened but instead of omit, it is possible to increase the hotel facility by

DO THE RIGHT THING @ THE RIGHT TIME!! [email protected]

METI GODERE HOTEL AND COMERCIAL BUILDING ELECTRICAL DESIGN MODIFICATION REQUEST

providing take away service for banks and shops through telephone instead of physically
appearing for order, so for this purpose I proposed to connect all provided line to the MDF
(main distribution frame) which will be installed in hotel at reception, as shown the
following block diagram

Hotel 3rd floor Hotel TTB Rj11 outlets

Rj11 outlets
Hotel 2nd floor Hotel Hotel TTB

Rj11 outlets Rj11 outlets

Hotel 1st floor Hotel Hotel TTB Hotel 1st floor Hotel TTB

Rj11 outlets
MDF @ Reception

125 pair from Tele

Figure 1 Tele lay out diagram

DO THE RIGHT THING @ THE RIGHT TIME!! [email protected]

METI GODERE HOTEL AND COMERCIAL BUILDING ELECTRICAL DESIGN MODIFICATION REQUEST

1.3. Site work Electrical Design Shop drawing is submitted so review it

1.4. First floor Commercial part Electrical design needs some modification due to the following
issue
1. Power standard
The hall system is not meet EBCS of electrical installation, its power for both sockets and
light points are supplied from SDB a 1st floor which is found 50 meter far from this
multipurpose hall and this SDB includes all light and socket circuits of the floor, so this
type of scheduling has many draw back these are:-
 Difficult to manage during maintenance and when accident happens
 Due to long distance the coast of electric wire will increase
 To sum up the design is not meet EBCS of electrical installation standards
1.1.Solution
To meet the standards and Providing SDB-HALL nearby the hall is the best solution,
The multi-purpose hall is found at right side of first floor, even wiring systems are
completed all main circuits of feeder lines are still not supplied to the branch circuits
of the room area and the line is accessible through the ceiling, so we have a chance to
isolate the light circuit from SDB 1st floor commercial and also the socket sources of
this room are collected in one pull box before to reach the end point so this situation
also makes easy to isolate the socket source from the previous distribution boards
1.2. Required Activities
To modify the systems the following activities are required these are:-
1.2.1. Locate one SDB-HALL with 25 A main three phase , 5 peace 16A single
phase, 6 pcs 10 A single phase and 25 % reserve space in suitable place of
the hall
1.2.2. Pulling out 3X2.5 mm conductor from previous line and re use the wire to
connect the pull box to the new proposed SDB-HALL and 2X2.5 mm
conductor in 16 mm PVC conduits from branch circuits to proposed SDB-
HALL for these activities only 2.6 meter chiseling of HCB is required
1.2.3. To satisfy the standard of Multi-purpose hall adding of two 1.2 kw socket
outlet line will be added for projector and amplifier on the center of new
proposed wooden stage

DO THE RIGHT THING @ THE RIGHT TIME!! [email protected]

METI GODERE HOTEL AND COMERCIAL BUILDING ELECTRICAL DESIGN MODIFICATION REQUEST

1.3.Required materials and coast analysis

Under this topics I have tried to mention the required material and analyze the cost to
decide the feasibility of the modified system.
For the above activities the following materials are required
1.3.1. SDB-HALL with, 25 A main three phase
2 pcs 25A single phase
7 pcs 16A single phase
6 pcs 10A single phase
25 % reserve space
1.3.2. 12 meter 5X6 mm square cable runs from SDB 1st floor hotel to new
proposed distribution boards SDB-HALL
1.3.3. 2 pcs 25A single phase socket outlet for amplifier and projector at the
center of wooden stage
1.3.4. 2 pcs 16A single phase socket outlet for general purpose load power rating
up to 1.5 KW

1.4.Estimated Material coast

ITEM
NO DESCRIPTION UNIT Qty U.P T.Price
SDB-HALL-flush mounted
distribution board with bus
bar of 80A and consisting of;
1 pc main 25A, MCCB,
3Phase
2 pc 25A, MCB, 1Phase
7 pc 16A, MCB, 1Phase
1 pc 10A, MCB, 1Phase
1 25 % Reserve space No 1 17,500.00 17,500.00

2 5X6 mm square cable ml 15 380.00 5,700.00

3 16A single phase socket outlet No 2 375.00 750.00

4 25A single phase socket outlet No 2 575.00 1,150.00

5 2.5 mm conductor ml 180 24.00 4,320.00
6 4 mm conductor ml 192 37.00 7,104.00
7 Tumbler Switch no 1 3200.00 3,200.00
8 Service coast ls 1 11,450.00 11,450.00
Total 51,174.00

DO THE RIGHT THING @ THE RIGHT TIME!! [email protected]

METI GODERE HOTEL AND COMERCIAL BUILDING ELECTRICAL DESIGN MODIFICATION REQUEST

1.5. Deducted coast

As I mentioned before the main light circuit lines which runs from SDB 1st floor
commercial to hall will be omitted so this coast will be deduct from initial coast.
When we calculate the conductor, 2X2.5 mm square 6*2*93.75 = 1,125 meter
When we change to birr it becomes 27,000 birr and out of 1345 meter removed socket
outlet 55 % of the wire which is 739.75 will be expected to re-use when we change
this wire to birr 17,754 birr, so from modification we have an indirect profit of 44,754
birr. When we deduct this opportunity coast from the total capital coast 51,174.00 birr
we will have 6,420.00

1.6. Conclusion
According to the result modifying the system is feasible

DO THE RIGHT THING @ THE RIGHT TIME!! [email protected]