Scribd Logo
Upload

Welcome to Scribd!

  • 31 views

    Extraction Tool 1-1579007-4: Instruction Sheet

    Uploaded by

    tirek
    pin

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Extraction Tool 1-1579007-4: Instruction Sheet

    Uploaded by

    tirek
    31 views2 pages
    pin

    Original Title

    1-1579007-4

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    pin

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    31 views2 pages

    Extraction Tool 1-1579007-4: Instruction Sheet

    Uploaded by

    tirek
    pin

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

     Instruction Sheet

     408-8942
    Extraction Tool 1-1579007-4 28 JUN 11 Rev A

    PROPER USE GUIDELINES


    Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
    and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

    Locking Latch 2. While holding the connector, grasp the wire at the
    rear of the housing and push forward toward the
    mating end to disengage the contact locking lance
    from the connector cavity shoulder. See Figure 2.

    Tool Tip

    Tool Cover

    Tool Handle

    Locking Latch

    Figure 1

    1. INTRODUCTION
    This instruction sheet covers the use of Extraction Tool
    Figure 2
    1-1579007-4, which is designed to remove Junior
    Power Timer (JPT) and 2.8mm Fastin-Faston tab 3. Fully insert the extraction tool tip into the window
    contacts from the connectors. adjacent to the circuit cavity until it bottoms inside
    NOTE Dimensions on this sheet are in millimeters unless the window. See Figure 3.
    otherwise specified. Figures are not drawn to scale. 4. Remove the contact from the connector by pulling
    i  on the wire attached to it.
    5. Perform the same procedure for removing
    2. DESCRIPTION contacts from Fastin-Faston connectors. See 
    Figure 4.
    Extraction Tool 1-1579007-4 consists of a tool handle,
    tool cover with locking latches, and an extraction tool 6. To protect the extraction tool tip when the tool is
    tip. Refer to Figure 1. not being used, depress the locking latches on the
    extraction tool cover and slide the cover over tip.
    The extraction tool tip is designed to enter the contact
    cavity in front of the connector and release the tab
    contact. When the extraction tool tip is bottomed in the
    contact cavity, the tip depresses the locking lance of
    the tab contact. The contact can then be removed
    from the housing by manually pulling on the wire.

    3. EXTRACTION PROCEDURE
    NOTE The secondary lock cover on the Junior Power
    Timer (JPT) and 2.8mm Fastin-Faston connectors
    must be in the pre-lock or open position before
    i attempting to remove a contact.
    1. Depress the locking latches (see Figure 1) on the
    extraction tool cover and slide the cover to expose
    the extraction tool tip.
    Figure 3

    © 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. 1 of 2
    All Rights Reserved PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service,
    *Trademark visit our website at www.te.com
    TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners. LOC B
    408-8942

    Push Wire and Insert Tool Into the Window 38 65

    1.5

    18

    Fully Insert Tool Into Window and Pull Wire


    107

    Figure 5

    5. REVISION SUMMARY
    • Removed old logos from graphics.
    • Corrected dimension line position in Figure 5.
    • Updated document to corporate requirements.
    Figure 4

    4. TOOL INSPECTION AND MAINTENANCE


    The extraction tool should conform to the dimensions
    indicated in Figure 5. It is recommended that the tool
    be inspected upon arrival and at regularly scheduled
    intervals to insure that the tool has not become
    damaged during handling.
    Additional tools may be ordered from:

    CUSTOMER SERVICE (038-035)


    TYCO ELECTRONICS CORPORATION
    PO BOX 3608
    HARRISBURG PA 17105-3608

    Rev A 2 of 2

    You might also like