C:\Users\jase\Desktop\Brown Issue\Frame-Jase3.

rpf

RAPT - Version: 6.6.1.0

Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2019 PCDC Pty. Ltd. All Rights Reserved

Licensee
E-Struct Consulting Pte Ltd
28 Sin Ming Lane
#06-134 Midview City
Singapore 573972
106480631800114WPN1

Input
General
Design Code List Singapore - Eurocode 2*SAVED*
Material List Singapore - Singapore Eurocode Materials*SAVED*
Reinforcement Type List Bonded Prestressed
Member Type List Beam
Panel Type List Internal
Strip Type List One way - Nominal Width
Column Stiffness List Equivalent Column
Concrete Type List Standard Concrete
Concrete - Spanning Members List C32/40MPa
Concrete - Columns List C32/40MPa
Top Reinforcement Cover mm 40
Bottom Reinforcement Cover mm 40
Top Reinforcement Axis Depth Limit mm 30
Bottom Reinforcement Axis Depth Limit mm 30
Concrete Unit Weight kn/m3 25
Self Weight Definition List Program Calculated
Pattern Live Load Y/N N
Earthquake Design List None
Moment Redistribution % 30
Design Surface Levels List Extreme Surfaces
Eurocode Ultimate Load Combination Basis List Eurocode Eqn 6.10

Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been
multiplied in the calculatiuons by 0.8

Span
Span Span Slab Panel Panel
Length Depth Width Width
Left Right
mm mm mm mm
LC 6400 400 8400 8400
1 8400 300 8400 8400
RE 0

Columns
Column Column Support Column Column Column Column Column Column Transverse Capital Depth Pin Percentage Braced Column Punching
Grid Type Height Width Length Height Width Length Column below Base Column frame Shortening Shear
Reference Above Above Above below below below spacing deepest below Stiffness at this Restrained Check
section column required
A List mm mm mm mm mm mm mm mm Y/N % Y/N Y/N Y/N
1 1 Column 4200 800 800 5400 800 800 8400 0 Y 100 Y N N
2 2 Column 4200 800 800 5400 800 800 8400 0 Y 100 Y N N

Beams
Beam Beam Beam Beam Length of Left Width of Left Width of centre Length of Right Width of Right
Number Depth Width Width Effective Effective Effective Effective Effective
at Flange Width Flange Width Flange Width Flange Width Flange Width
Slab Zone Zone Zone Zone Zone
mm mm mm mm mm mm mm mm
LC 1200 1500 1500 1260 4412 3882 6400 4412
1 1200 1500 1500 1260 4412 3852 1260 2004
RAPT 6.6.1.0 6/3/2023 12:28:38 pm Page 2/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1
Steps
Step Description Reference Distance from Flexible/Rigid
Number Column Reference Step
Column
A # mm List
1 1 0 Flexible Step

Steps(1) : Vertical
Layer Shape Step this Step Step Taper Fall
Attribute to attribute of Offset Depth Length Depth
step this shape
Y/N mm mm mm mm
Slab Panel Y 0 -200 0 0
N
Downturn Beam N

Load Cases
Load Load Type Load Definition Live Load Description
Case Deflection
Case
List List Y/N A
1 Self Weight Applied Loads
2 Extra Dead Load Applied Loads
3 Live Load Applied Loads Y

1. Self Weight - Line

Load Left End Left end of Load at Right Right end of Load at Description
Reference load from left end End load from right
Column reference reference reference end
column column column
# mm kN/m # mm kN/m A
1 0 0 114 0 1260 114
2 0 1260 114 1 0 114
3 1 0 138.75 1 1260 138.75
4 1 1260 138.75 1 7140 138.75
5 1 7140 138.75 2 0 138.75

2. Extra Dead Load - Panel

Load Left End Left end of Load at Right Right end of Load at Description
reference load from left end End load from right
column reference reference reference end
column column column
# mm kN/m2 # mm kN/m2 A
1 0 0 4.8 2 0 4.8

2. Extra Dead Load - Point

Load Reference Distance to Load Load Description
column Load from Length
reference
column
# mm kN mm A
1 0 3400 671 0

3. Live Load - Panel

Load Left End Left end of Load at Right Right end of Load at Live Description
reference load from left end End load from right Load
column reference reference reference end reduction
column column column
# mm kN/m2 # mm kN/m2 #.# A
1 0 0 7.5 2 0 7.5 1

3. Live Load - Point

Load Reference Distance to Load Load Live Description
column Load from Length Load
reference reduction
column
# mm kN mm #.# A
1 0 3400 123 0 1
RAPT 6.6.1.0 6/3/2023 12:28:40 pm Page 3/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1
Load Combinations : Ultimate
Load Description Prestress Prestress 1. Self 2. Extra 3.
Combination Secondary Secondary Weight Dead Live
Adverse Beneficial Load Load
A #.# #.# #.# #.# #.#
1 Live Load 1 1 1.35 1.35 1.5
2 Live Load 1 1 1 1 1.5
3 Dead Load 1 1 1.35 1.35 0

Load Combinations : Short Term Service

Load Description Long-term 1. Self 2. Extra 3. Live
Combination Prestress Weight Dead Load Load
A #.# #.# #.# #.#
1 Live Load 1 1 1 0.5

Load Combinations : Permanent Service

Load Description Long-term 1. Self 2. Extra 3. Live
Combination Prestress Weight Dead Load Load
A #.# #.# #.# #.#
1 Live Load 1 1 1 0.3

Load Combinations : Deflection

Load Description Long-term 1. Self 2. Extra 3. Live
Combination Prestress Weight Dead Load Load
A #.# #.# #.# #.#
1 Short Term - Deflection 1 1 1 0.5
2 Permanent - Deflection 1 1 1 0.3
3 Initial - Deflection 1 1 0 0

Load Combinations : Transfer Prestress

Load Description Transfer 1. Self 2. Extra 3. Live
Combination Prestress Weight Dead Load Load
A #.# #.# #.# #.#
1 Transfer 1 1 0 0

Load Combinations : Pre Existing

Load Description Long-term 1. Self 2. Extra 3. Live
Combination Prestress Weight Dead Load Load
A #.# #.# #.# #.#
1 Pre Existing 1 1 0 0

Load Combinations : Construction

Load Description Long-term 1. Self 2. Extra 3. Live
Combination Prestress Weight Dead Load Load
A #.# #.# #.# #.#
1 Construction 1 1 0 0

Load Case 1 : 1. Self Weight

kN/m 1 2
160 L3 L4 L5
120 L1 L2
80
40
0
6400 14800mm

Load Case 2 : 2. Extra Dead Load

kN/m 1 2kN
160 960
120 1 720
80 480
40 240
0 0
6400 14800mm
160 960
120 720
80 P1 P1 P1 P1 P1 480
40 240
0 0
1 2
RAPT 6.6.1.0 6/3/2023 12:28:42 pm Page 4/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1
Load Case 3 : 3. Live Load

kN/m 1 2kN
160 960
120 720
80 480
40 1 240
0 0
6400 14800mm
160 960
120 720
80 P1 P1 P1 P1 P1 480
40 240
0 0
1 2

Prestress
Tendon Normal or Steel Steel Prestress Prestress Number Number Spacing Top Bottom Left Distance to Left Coupler at
upside down Type Diameter Type Anchorage of of of Cover Cover Anchorage left Anchorage Left
profiles Size Strands Tendons tendons to to Duct Reference anchorage Type Anchorage
Duct Column from column
List List List List List List #.# mm mm mm # mm List Y/N
1 Strand 12.7mm MultiStrand 27 27 2 50 50 0 0
2 Strand 12.7mm MultiStrand 27 27 3 50 50 0 0

Tendon Right Distance to Right Coupler at Stacked tendons, Tendon

Anchorage Right Anchorage Right No effect on Length
Reference Anchorage from Type Anchorage effective shear
Column Column width
# mm List Y/N List mm
1 2 0 Individual 14800
2 2 0 Individual 14800

Tendon 1 : - Drape Locations

Span Tendon Length of Left End Length of Right End Reverse Number of strands Number of Number of Extra Tendon Number
Profile Type Straight Straight Curve from left end strands from strands angle Profile of strands
Section/Start of Section/End of Radius terminating in span left end from right change Point full length
Drape Section in Drape Section in and restarting before terminating terminating in this Spacing of tendon
Span Span end of tendon in span in span span in span
List mm mm mm # # # #.# mm #
LC 0 0 6650 0 0 0 0 1000 27
1 0 0 6650 0 0 0 0 1000 27

Tendon 1 : - Allowable Profiles

Span Tendon Cover Tendon Cover to Tendon Cover Available Relative
to centreline at duct at low point to duct at right Parabola Minimum
left end of of parabola end of span Drape Tendon
span Ratio
mm mm mm mm #.#
LC 394.5 50 326.8 1
1 50 50 599.5 587.6 0.528

Tendon 1 : - Adopted Profiles

Span Profile Profile Profile Profile Adopted Percentage of Prestress Balanced
Height height at Height at height at Parabolic available Force Uniform
Datum left end midpoint of right end Drape parabolic drape Load
of span parabola of span adopted
mm mm mm mm mm % kN %
LC 1200 570 1050 292.8 89.608 98.44 66.678
1 1200 1050 680 570 130 22.125 104.36 59.863

Tendon 1 : - Details
Reverse Curve at Left Anchorage Y/N N
Reverse Curve at Right Anchorage Y/N N
Percentage Jacking Force % 75
Include Secondary Prestress Effects Y/N Y
External Tendon Y/N N
Grouted At Transfer Y/N N

Tendon 1 : - Jacking Sequence

Stage Proportion of Stressing Concrete
Jacking force Time in Strength
applied at this days
stage
% #.# MPa
25 0.7 9
RAPT 6.6.1.0 6/3/2023 12:28:43 pm Page 5/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1

Stage Proportion of Stressing Concrete

Jacking force Time in Strength
applied at this days
stage
% #.# MPa
75 8 25
0 0 0
0 0 0

Tendon 2 : - Drape Locations

Span Tendon Length of Left End Length of Right End Reverse Number of Extra Tendon Number
Profile Type Straight Straight Curve strands from angle Profile of strands
Section/Start of Section/End of Radius left end change Point full length
Drape Section in Drape Section in terminating in this Spacing of tendon
Span Span in span span in span
List mm mm mm # #.# mm #
LC 0 0 6650 0 0 1000 27
1 0 0 6650 0 0 1000 27

Tendon 2 : - Allowable Profiles

Span Tendon Cover Tendon Cover to Tendon Cover Available Relative
to centreline at duct at low point to duct at right Parabola Minimum
left end of of parabola end of span Drape Tendon
span Ratio
mm mm mm mm #.#
LC 394.5 50 326.8 1
1 50 50 599.5 839.6 0.386

Tendon 2 : - Adopted Profiles

Span Profile Profile Profile Profile Adopted Percentage of Prestress Balanced
Height height at Height at height at Parabolic available Force Uniform
Datum left end midpoint of right end Drape parabolic drape Load
of span parabola of span adopted
mm mm mm mm mm % kN %
LC 1200 800 1050 292.8 89.608 100.53 102.134
1 1200 1050 900 900 75 8.933 103.95 51.603

Tendon 2 : - Details
Reverse Curve at Left Anchorage Y/N N
Reverse Curve at Right Anchorage Y/N N
Percentage Jacking Force % 75
Include Secondary Prestress Effects Y/N Y
External Tendon Y/N N
Grouted At Transfer Y/N N

Tendon 2 : - Jacking Sequence

Stage Proportion of Stressing Concrete
Jacking force Time in Strength
applied at this days
stage
% #.# MPa
25 0.577 9
75 8 25
0 0 0
0 0 0

Tendon 1 : - Gross Extension: 87.8mm - 2 - 27/12.7

Profile Heights
Span 0 Locat mm 0 914.3 1828.6 2742.9 3657.1 4571.4 5485.7 6400
Height mm 570 530 570 630 710 820 950 1015
Span 1 Locat mm 0 933.3 1866.7 2800 3733.3 4666.7 5600 6533.3 7466.7 8400
Height mm 1015 950 830 730 650 585 540 515 510 570

Critical Profile Points

Span 0 Locat mm 0 5370.2 6400
Height mm -680.5 -264.7 -185
Span 1 Locat mm 0 918.7 7346.4 8400
Height mm -185 -248.4 -692.4 -680.5
RAPT 6.6.1.0 6/3/2023 12:28:45 pm Page 6/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1
Tendon 2 : - Gross Extension: 89.3mm - 3 - 27/12.7
Profile Heights
Span 0 Locat mm 0 914.3 1828.6 2742.9 3657.1 4571.4 5485.7 6400
Height mm 800 755 775 805 845 900 965 1015
Span 1 Locat mm 0 933.3 1866.7 2800 3733.3 4666.7 5600 6533.3 7466.7 8400
Height mm 1015 970 915 875 845 825 815 815 830 900

Critical Profile Points

Span 0 Locat mm 0 5848.2 6400
Height mm -450.5 -207.9 -185
Span 1 Locat mm 0 444.9 5993.2 8400
Height mm -185 -199.8 -385.4 -350.5

mm Tendon 1 : - 2 - 27/12.7
400
0

27 27
-400
2727

-800
-1200

1 2
570cl

570cl
1015
530

570

630

710

820

950

950

830

730

650

585

540

515

510
mm Tendon 2 : - 3 - 27/12.7
400
0

27 27
-400
2727

-800
-1200

1 2
800cl

900cl
1015
755

775

805

845

900

965

970

915

875

845

825

815

815

830
Reinforcement
Reinforcement Reinforcement Preferred Number
Use Type Bar Size of Legs
List List #
Flexural Bar H 500MPa
Flexural Mesh A 500MPa
Shear Option 1 H 500MPa 10 8
Shear Option 2 H 500MPa 10 8
Shear Option 3 H 500MPa 10 8
Punching Shear H 500MPa 10 8

Reinforcement
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Bar Bar Continuous Reinforcement Reinforcement Bars Bars
Spacing Spacing Reinforcement into End into Internal
Support Support
mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
Span Reinforcement 300 60 0 0 N N

Design Zones
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred Minimum Maximum
Number type Reference left end of length at left Cover at Reference right end of length at at Right Bar Size Bar Size bar size Number of Spacing of
Column bar end left end Column bar right end end Bars Bars
List # mm mm mm # mm mm mm List List List # mm
1 Bar 1 -6400 0 40 2 0 0 40 25 25 25 0 0

Layer Minimum % in
Number Steel area as Flange
%
% %
1 0 0
RAPT 6.6.1.0 6/3/2023 12:28:47 pm Page 7/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1
Design Zones
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred Minimum
Number type Reference left end of length at left Cover at left Reference right end of length at Cover at Bar Size Bar Size bar size Number of
Column bar end end Column bar right end Right End Bars
List # mm mm mm # mm mm mm List List List #
1 Bar 1 -6400 0 40 2 0 0 40 40 20 32 0

Layer Maximum Minimum % in

Number Spacing of Steel area as Flange
Bars %
mm % %
1 0 0 0

Reinforcement Design Zones

1 2

mm
0

-400

-800

-1200
6400 14800mm
Design Data
Capacity Reduction factor (phi) for Flexure #.# 1
Capacity Reduction factor (phi) for Shear #.# 1
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1
Material Factor for Concrete in Flexure #.# 1.5
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58
Ductility Limit - Strain #.# 0
Ductility Check at Left End Column Y/N Y
Ductility Check at Right End Column Y/N Y
Minimum Reinforcement Strength Limit - #.## x M* #.# 0
Flexural Critical Section - Consider Transverse Beams Y/N Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40
Prestress Minimum Reinforcement Basis List Program Default
Shear Enhancement at Supports Y/N N
Ast Value in Shear Calculations List Calculated
Limit Reinforcement Strain Y/N Y
Include Strain Hardening of Reinforcement Y/N N
Beam Shear Critical Section Location List Code Critical Section

Maximum Service Stress Change - Prestressed Sections MPa 150

Maximum Service Stress Change - Reinforced Sections MPa 0
Relative Humidity % 50
Average Temperature C. 20
Prestress Losses Calculations based on List Program Default
Crack Width Calculations List Code default
AS3600 Shrinkage and Temperature Reinforcement List Moderate
Degree of Restraint in Primary Direction % 0
Degree of Restraint in Secondary Direction % 0
Concrete Strength Gain Rate List N

Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1

Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
Total Deflection Warning Limit - Maximum Deflection mm 25
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 250
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Initial Time for Shrinkage List Full Shrinkage
Time of Loading in days #.# 10
Age Adjustment Factor #.# 0.76
Concrete Strength at Time of Loading MPa 27.04
Loaded Period in years #.# 30
Tension stiffening Approach List Modified Concrete Tensile Modulus Method

Live Load Pattern Factor #.#

Pattern Live Load for Ultimate Strength Y/N
Pattern Live Load for Crack Control Y/N
Pattern Live Load For Deflections Y/N
RAPT 6.6.1.0 6/3/2023 12:28:49 pm Page 8/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1

Pattern Live Load for Deflection Permanent Load Combination Y/N

Material Properties
Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
Characteristic Compressive Strength MPa 40
Mean Compressive Strength MPa 50
Lower Characteristic Tensile Strength MPa 2.12
Upper Characteristic Tensile Strength MPa 3.93
Concrete Density kg/m3 2447
Design Concrete Modulus MPa 31186.6
Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0
Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 2.656
Creep Multiplier #.# 1
Concrete Strain at Peak Stress #.# 0.002
Squash Load Factor #.# 0.85
Concrete Strain Limit #.# 0.004
Strength Gain Rate List Normal
Maximum Aggregate Size mm 20

Prestress Strand
Diameter Area Breaking Proof 1% Breaking Design Elastic Plastic Basic Weight Material Material Material Material Capacity
Load Stress Stress Strain Strain Modulus Modulus Relaxation Factor Factor Capacity Reduction Factor
Limit Flexure Shear Reduction - Shear
Factor - Flexure
12.7 98.7 183.6 85 82 0.06 90 1.95e5 2200 2.5 0.77 -1 -1 -1 -1

Include as Set as Description

Flexural default
Reinforcement for
Shear
Y Y Low Relaxation

Bonded Multistrand
Anchorage Description Duct Transfer Anchor Draw-in Maximum Set as
Size Type Concrete Friction Jacking default
Strength Force
27 Steel 30 2 6 75 N

Live Deformed Nominal Full

End Strand Dead Swaged Dead Swaged
End End Dead End
Ineffective Length mm 100 100 100 100
Force at Start of Transition % 100 40 50 100
Transition Length mm 0 1200 750 0
Force at End of Transition % 100 100 100 100

Number Duct Duct Wall Centroid Duct Wobble - Minimum

of Diameter Thickness Distance Friction Unintentional Reverse
Cables Friction - K Curve Radius
# mm mm mm #.# 1/m mm
20 101 3 21.9 0.2 0.002 6650
21 101 3 21.1 0.2 0.002 6650
22 101 3 20.2 0.2 0.002 6650
23 101 3 19.1 0.2 0.002 6650
24 101 3 18.3 0.2 0.002 6650
25 101 3 17.3 0.2 0.002 6650
26 101 3 16.4 0.2 0.002 6650
27 101 3 15.5 0.2 0.002 6650

Reinforcement Bar
Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Material Capacity Include as Description
Stress Modulus Strain Stress Strain Factor Factor Capacity Reduction Factor Flexural
Limit Flexure Shear Reduction - Shear Reinforcement for
Factor - Flexure Shear
H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y

Nominal Bar Bar Bar Bar Stock

Bar Size Diameter Area Inertia Weight Length
A mm mm2 mm4 kg/m mm
10 10 78.5 491.07 0.62 12000
RAPT 6.6.1.0 6/3/2023 12:28:51 pm Page 9/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1

Nominal Bar Bar Bar Bar Stock

Bar Size Diameter Area Inertia Weight Length
A mm mm2 mm4 kg/m mm
13 13 132.7 1402.55 1.04 12000
16 16 201.1 3218.29 1.58 12000
20 20 314.2 7857.14 2.47 12000
22 22 380.1 11503.6 2.98 12000
25 25 490.9 19182.5 3.85 12000
32 32 804.2 51492.6 6.31 12000
40 40 1256.6 1.257e5 9.86 12000

Elevation view
1 2

mm
0

-400

-800

-1200
6400 14800mm

Plan view

mm 1 2
-4000

-2000

2000

4000
6400 14800mm

Full Elevation View

mm 1 2
4000
2000
0
-2000
-4000

6400 14800mm
Warnings
Input
No errors or warnings were found.

Output
Warning:SUPPORT Reinforcing Bar Spacing There have been problems in determining a bar size to satisfy the design spacing requirements. See Detailed
Reinforcement Design Comments.
Warning:SPAN Reinforcing Bar spacing There have been problems in determining a bar size to satisfy the design spacing requirements. See Detailed
Reinforcement Design Comments.

Bending Moments
Load Cases
Column Actions
Col No. 1 Secondary Secondary Prestress Prestress Self Extra Live Load
Transfer Service Transfer Service Weight Dead
Load
Moment Above kNm 184 160.1 184 160.1 -266.61 -526.73 -245.5
Moment Below kNm 92.8 80.75 92.8 80.75 -134.47 -265.66 -123.82
Reaction kN 66.97 57.74 66.97 57.74 1524.92 1357.88 942.21
Elastic Rotation #.# 1e-4 0 1e-4 0 -1.46e-4 -2.88e-4 -1.34e-4
Elastic Axial Shortening mm -0 -0 -0 -0 -0.3 -0.3 -0.2

Col No. 2 Secondary Secondary Prestress Prestress Self Extra Dead Live
Transfer Service Transfer Service Weight Load Load
Moment Above kNm 187.14 159.94 187.14 159.94 -96.99 87.32 -11.85
Moment Below kNm 98.58 84.25 98.58 84.25 -51.09 45.99 -6.24
Reaction kN -66.97 -57.74 -66.97 -57.74 370.18 -90.14 113.19
RAPT 6.6.1.0 6/3/2023 12:28:52 pm Page 10/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1

Col No. 2 Secondary Secondary Prestress Prestress Self Extra Dead Live
Transfer Service Transfer Service Weight Load Load
Elastic Rotation #.# 0 0 0 0 0 0 0
Elastic Axial Shortening mm 0 0 0 0 -0 0 -0

Load Combinations
Column Actions
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm -878.74 -878.74 -755.99 -755.99 -1279.16 -910.91 -910.91 -1279.16
Moment Below kNm -443.2 -443.2 -381.29 -381.29 -645.15 -459.42 -459.42 -645.15
Reaction kN 3882.75 3882.75 3411.64 3411.64 5362.83 3949.51 3949.51 5362.83
Elastic Rotation #.# -4.8e-4 -4.8e-4 -4.13e-4 -4.13e-4 -6.99e-4 -4.98e-4 -4.98e-4 -6.99e-4
Elastic Axial Shortening mm -0.9 -0.9 -0.8 -0.8 -1.2 -0.9 -0.9 -1.2

Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 138.42 138.42 144.35 144.35 129.11 146.89 146.89 129.11
Moment Below kNm 72.91 72.91 76.03 76.03 68.01 77.37 77.37 68.01
Reaction kN 335.49 335.49 278.89 278.89 490.1 320.31 320.31 490.1
Elastic Rotation #.# 0 0 0 0 0 0 0 0
Elastic Axial Shortening mm -0 -0 -0 -0 -0.1 -0 -0 -0.1

Ultimate Flexure

kNm 1 2
-12000
-10000 -8286
-8000 -6642
-6000
-4000
-2000 366
0
2000 554
4000
6000
6400 14800mm

Moment Moment 1 Moment 2

1 2
kN
2700 1823
1800
900 47.1
0
-900
-1800
-2700
-3600 -2617
6400 14800mm

Shear Shear 1 Shear 2

Flexural Design
Ultimate

mm2 1 2
50000
40000 0 36101
30000
20000
10000
0
-10000
-20000
-30000
-40000 11962 34178
6400 14800mm

Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
RAPT 6.6.1.0 6/3/2023 12:28:54 pm Page 11/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1

1 2
kNm
-21000
-14000
-7000
0
7000
14000
21000
28000
6400 14800mm

Capacity Minimum Ultimate Design Initial Final

1 2

0.579
0.9

0.208
0.6
0.3
0
-0.3

0.208
-0.6
-0.9
6400 14800mm

Neutral Axis Depth Initial Final

Span 0
Design Comments:-
- Compression reinforcement added at right support hinge location for ductility in accordance with Eurocode 2 cl.5.5. Asc = 11962mm2 @ 6000mm

Span 1
Design Comments:-
- Compression reinforcement added at left support hinge location for ductility in accordance with Eurocode 2 cl.5.5. Asc = 34178.3mm2 @ 400mm
- Compression reinforcement added at span hinge location for ductility in accordance with Eurocode 2 cl.5.5. Asc = 36101.1mm2 @ 7141mm

Service
Maximum Moment Condition

MPa 1 2MPa
-6 -15
-4 -10
-2 -5
0 0
2 0 0 5
4 10
6 15
8 7.2 6.35 20
6400 14800mm

Gross Stress Top Gross Stress Bottom Cracked Compression Axial Prestress Reinforcement Tension

Reversal Moment Condition

MPa 1 2MPa
-6 -15
-4 -10
-2 -5
0 0
2 0 0 5
4 10
6 15
8 7.2 6.35 20
6400 14800mm

Gross Stress Top Gross Stress Bottom Cracked Compression Axial Prestress Reinforcement Tension
RAPT 6.6.1.0 6/3/2023 12:28:56 pm Page 12/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1
Transfer Prestress
Maximum Moment Condition
1 2
MPa MPa
-9 -15
-6 -10
-3 -5
0 0 0 0
3 5
6 10
9 8.24 7.12 15
6400 14800mm

Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension

Permanent
Maximum Moment Condition
1 2
MPa MPa
-4 -12
-2 -6
0 0
2 0 0 6
4 12
6 18
6.63 6.07
6400 14800mm

Gross Stress Top Gross Stress Bottom Cracked Compression Axial Prestress Reinforcement Tension

Reversal Moment Condition

1 2
MPa MPa
-4 -12
-2 -6
0 0
2 0 0 6
4 12
6 18
6.63 6.07
6400 14800mm

Gross Stress Top Gross Stress Bottom Cracked Compression Axial Prestress Reinforcement Tension

Characteristic Service
Maximum Moment Condition
1 2
MPa MPa
-8 -10.67
-6 -8
-4 -5.33
-2 -2.67
0 0
2 0 0 2.67
4 5.33
6 8
8 8.62 7.06 10.67
10 13.33
6400 14800mm

Gross Stress Top Gross Stress Bottom Cracked Compression Axial Prestress Reinforcement Tension

Reversal Moment Condition

1 2
MPa MPa
-8 -10.67
-6 -8
-4 -5.33
-2 -2.67
0 0
2 0 0 2.67
4 5.33
6 8
8 8.62 7.06 10.67
10 13.33
6400 14800mm

Gross Stress Top Gross Stress Bottom Cracked Compression Axial Prestress Reinforcement Tension
RAPT 6.6.1.0 6/3/2023 12:28:58 pm Page 13/16
Licensee: License No.: 106480631800114WPN1
Shear Design
Beam
Span 0
Locat V* Mv* Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s

mm kN kNm kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm

101 -30.59 -1.54 2751.53 708.1 0 1500 99999 3278.65 3278.65 6436.65 940.51 0 21.8 1.36
630 -190.78 -60.1 2807.06 711.8 0 1500 99999 3282.17 3282.17 6580.41 945.41 0 21.8 1.36
945 -286.18 -135.22 2873.05 716.5 0 1500 99999 3283.97 3283.97 6689.58 951.7 0 21.8 1.36
1259 -381.27 -240.01 2963.5 723.1 0 1500 99999 3285.54 3285.54 6815.92 960.47 0 21.8 1.36
1261 -381.87 -240.77 2964.16 723.2 0 1500 99999 3285.55 3285.55 6816.78 960.53 0 21.8 1.36
1600 -484.53 -387.62 3089.79 732.4 0 1500 99999 3286.97 3286.97 6972.96 972.82 0 21.8 1.36
2134 -646.24 -689.54 3346.68 751.4 0 1500 99999 3288.54 3288.54 7260.34 998.08 0 21.8 1.36
2667 -807.65 -1077.01 3675.42 775.8 0 1500 99999 3289.14 3289.14 7597.47 1030.5 0 21.8 1.36
3200 -969.06 -1550.5 4076.4 805.7 0 1500 99999 3288.53 3288.53 7984.43 1070.12 0 21.8 1.36
3399 -1029.33 -1749.34 4244.5 818.2 0 1500 99999 3287.93 3287.93 8141.55 1086.76 0 21.8 1.36
3401 -2120.28 -1752.49 4246.25 818.3 0 1500 99999 3287.88 3287.88 8143.17 1086.93 0 21.8 1.36
3830 -2250.2 -2689.96 4648.61 847.9 0 1500 99999 3269.08 3269.08 8507.42 1126.23 0 21.8 1.36
4315 -2397.07 -3816.92 5163.49 885.6 0 1500 99999 3247.44 3247.44 8959.38 1176.28 0 21.8 1.36
4800 -2543.94 -5015.11 5742.62 927.8 0 1500 99999 3225.28 3225.28 9453.9 1232.29 0 21.8 1.36
5040 -2616.62 -5634.38 6053.03 950.3 0 1500 99999 3214.07 3214.07 9714.29 1262.21 0 21.8 1.36
6000 -2907.34 -8285.89 7340.24 1038 0 1500 0 0 0 10126.4 0 0 0 0

Spacing of Sets Minimum Legs Shear Comments

8 legs 8 legs 8 legs Min legs
H10 H10 H10 H10
mm mm mm mm # A
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
0 0 0 0 0

Span 1
Locat V* Mv* Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s

mm kN kNm kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm

400 2199.86 -6641.9 6161.5 1038.1 0 1500 0 0 0 9938.72 0 0 0 0
1520 1829.91 -4423.27 5237.9 956.8 0 1500 99999 3716.37 3716.37 9515.9 1270.86 0 21.8 1.36
1810 1732.4 -3906.74 4978.47 936.8 0 1500 99999 3723.06 3723.06 9283.64 1244.22 0 21.8 1.36
2100 1652.84 -3508.88 4734.59 917.8 0 1500 99999 3726.88 3726.88 9061.21 1218.99 0 21.8 1.36
2800 1417.47 -2434.27 4209.49 876.3 0 1500 99999 3740.97 3740.97 8564.7 1163.93 0 21.8 1.36
3500 1212.35 -1639.73 3773.5 841 0 1500 99999 3749.79 3749.79 8125.27 1117.1 0 21.8 1.36
4200 1020.19 -1014.24 3425.63 812 0 1500 99999 3756.4 3756.4 7742.78 1078.52 0 21.8 1.36
4900 808.1 -529.95 3157.87 789.2 0 1500 99999 3759.35 3759.35 7415.09 1048.18 0 21.8 1.36
5600 451.38 251.32 3577.95 627.5 0 1500 99999 3769.52 3769.52 5835.48 833.44 0 21.8 1.36
6300 439.73 208.03 3657.28 637.9 0 1500 99999 3759.54 3759.54 5808.18 847.3 0 21.8 1.36
6590 352.01 231.44 3665.71 640.4 0 1500 99999 3757.23 3757.23 5780.83 850.63 0 21.8 1.36
6880 284.65 251.94 3659.93 642.2 0 1500 99999 3755.24 3755.24 5813.74 852.99 0 21.8 1.36
8000 -583.92 252.2 2289.72 680.8 0 1500 0 0 0 6378.59 0 0 0 0

Spacing of Sets Minimum Legs Shear Comments

8 legs 8 legs 8 legs Min legs
H10 H10 H10 H10
mm mm mm mm # A
0 0 0 0 0
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 289.1 5 Minimum Steel
RAPT 6.6.1.0 6/3/2023 12:29:00 pm Page 14/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1

Spacing of Sets Minimum Legs Shear Comments

8 legs 8 legs 8 legs Min legs
H10 H10 H10 H10
mm mm mm mm # A
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
462.6 462.6 462.6 231.3 4 Minimum Steel
0 0 0 0 0

Punching
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Requested!
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Requested!

Deflections
All Spans Loaded
Transfer
1 2
mm
6

2.74
0
0.371
-6

-12

-18 2333 22637

6400 14800mm

Short Term
1 2
mm
6

0
0.781
-6
-4.84
-12

-18 1323 10755

6400 14800mm

Incremental
1 2
mm
6

0
0.597
-6
-6.1
-12

-18 1049 14082

6400 14800mm

Total Long Term

1 2
mm
6

0
0.863
-6
-4.62
-12

-18 1385 9738

6400 14800mm
RAPT 6.6.1.0 6/3/2023 12:29:02 pm Page 15/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1
Detailed Reinforcement
Span 0
Top Reinforcement Bottom Reinforcement

Max Max Section Max Max Section

Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A
101 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
630 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
945 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
1259 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
1261 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
1600 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
2134 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
2667 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
3200 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
3399 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
3401 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
3830 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
4315 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
4800 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
5040 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
5280 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
5520 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
5760 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
6000 0 0 0 52.5 4412 No Steel Added 0 0 11962 1144 1500 15 H32 @ 98.8
Shear Reinforcement
Spacing of Sets
8 legs 8 legs 8 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0

Span 1
Top Reinforcement Bottom Reinforcement

Max Max Section Max Max Section

Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A
400 0 0 0 52.5 4412 No Steel Added 0 0 34538.1 1344 1500 28 H40 @ 50.9
630 0 0 0 52.5 4412 No Steel Added 0 0 34538.1 1344 1500 28 H40 @ 50.9
944 0 0 0 52.5 4412 No Steel Added 0 0 34538.1 1344 1500 28 H40 @ 50.9
1259 0 0 0 52.5 4412 No Steel Added 0 0 34538.1 1344 1500 28 H40 @ 50.9
1261 0 0 0 52.5 3852 No Steel Added 0 0 34538.1 1344 1500 28 H40 @ 50.9
1520 0 0 0 52.5 3852 No Steel Added 0 0 34538.1 1344 1500 28 H40 @ 50.9
1810 0 0 0 52.5 3852 No Steel Added 0 0 34538.1 1344 1500 28 H40 @ 50.9
2100 0 0 0 52.5 3852 No Steel Added 0 0 34538.1 1344 1500 28 H40 @ 50.9
2800 0 0 0 52.5 3852 No Steel Added 0 0 34538.1 1344 1500 28 H40 @ 50.9
3500 0 0 0 52.5 3852 No Steel Added 0 0 34538.1 1344 1500 28 H40 @ 50.9
4200 0 0 0 52.5 3852 No Steel Added 0 0 34538.1 1344 1500 28 H40 @ 50.9
4900 0 0 0 52.5 3852 No Steel Added 0 0 34538.1 1344 1500 28 H40 @ 50.9
5600 0 0 28145.8 52.5 3852 58 H25 @ 24.4 0 0 0 1344 1500 No Steel Added
6300 0 0 27520.5 52.5 3852 57 H25 @ 24.8 0 0 0 1344 1500 No Steel Added
6590 0 0 27388.5 52.5 3852 56 H25 @ 25.3 0 0 0 1344 1500 No Steel Added
6880 0 0 27345.3 52.5 3852 56 H25 @ 25.3 0 0 0 1344 1500 No Steel Added
6918.2 0 0 27341.8 52.5 3852 56 H25 @ 25.3 0 0 0 1344 1500 No Steel Added
7139 0 0 27332.3 52.5 3852 56 H25 @ 25.3 0 0 0 1344 1500 No Steel Added
7141 0 0 36101.1 52.5 2004 74 H25 @ 19 0 0 0 1344 1500 No Steel Added
7550 0 0 31090 52.5 2004 64 H25 @ 22.1 0 0 0 1344 1500 No Steel Added
RAPT 6.6.1.0 6/3/2023 12:29:04 pm Page 16/16
Licensee: E-Struct Consulting Pte Ltd License No.: 106480631800114WPN1
Top Reinforcement Bottom Reinforcement

Max Max Section Max Max Section

Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A
7770 0 0 28954.4 52.5 2004 59 H25 @ 24 0 0 0 1344 1500 No Steel Added
8000 0 0 26749.4 52.5 2004 55 H25 @ 25.7 0 0 0 1344 1500 No Steel Added
Shear Reinforcement
Spacing of Sets
8 legs 8 legs 8 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 289.1 5 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
1.36 462.6 462.6 462.6 231.3 4 Minimum Steel
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0

Design Comments:-
- SUPPORT Reinforcing Bar Spacing - Column Grid 2 - Largest preferred reinforcement size requires bar spacing smaller then minimum. It will be necessary
to use larger bars than the preferred maximum size, place more reinforcement in the flange if possible or place reinforcement in multiple layers.
- SPAN Reinforcing Bar spacing - Span 1 - Largest preferred reinforcement size requires bar spacing smaller then minimum. It will be necessary to use larger
bars than the preferred maximum size, place more reinforcement in the flange if possible or place reinforcement in multiple layers.
- - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than calculated.
RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout.

Reinforcement Layout
1 2
1-H25
1-H25

mm
0

-400

-800

-1200
28-H40
15-H32

6400 14800mm

- SUPPORT Reinforcing Bar Spacing - Column Grid 2 - Largest preferred reinforcement size requires bar spacing smaller then minimum. It will be necessary
to use larger bars than the preferred maximum size, place more reinforcement in the flange if possible or place reinforcement in multiple layers.
- SPAN Reinforcing Bar spacing - Span 1 - Largest preferred reinforcement size requires bar spacing smaller then minimum. It will be necessary to use larger
bars than the preferred maximum size, place more reinforcement in the flange if possible or place reinforcement in multiple layers.
- - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than calculated.
RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout.