International Letters of Chemistry, Physics and Astronomy Online: 2015-09-14

ISSN: 2299-3843, Vol. 59, pp 1-9

doi:10.18052/www.scipress.com/ILCPA.59.1
2015 SciPress Ltd, Switzerland

Physicochemical characteristics of groundwater from Kumbakonam

Taluk of Thanjavur District - Tamilnadu (India)
D. Kannan 1*, S. Nedunchezhian2 and N. Mani 3
1, 2,3
Department of Chemistry, A. V. V. M. Sri Pushpam College, Poondi, Thanjavur.
E-mail: [email protected]

Keywords: Physicochemical parameters, Kumbakonam region, ground water quality.

ABSTRACT The aim of present study was to assess the quality of ground water from
Kumbakonam region in Thanjavur district, and check its fitness for drinking and other purpose. An
eight ground water samples were collected from various parts of Kumbakonam region. The
physicochemical parameters such as calcium, magnesium, chloride was determined by titration
method, sulphate, nitrate, nitrite were analyzed by spectrophotometric method, pH was determined
by pH metric method and other parameters were analyzed by Indian standard method.
Physicochemical parameter of ground water samples were compared with standard limits
recommended by BIS. The comparative study of ground water to this region, all the collected water
samples are not suitable for drinking purpose, because in this region ground water samples had
excess of manganese, calcium, magnesium and iron content.

1. INTRODUCTION
Water is extremely indispensable for survival of all living organism. The quality of water is
vital concern for mankind since it is directly linked with human safety. In India, most of the
population is dependent on groundwater as the only source of drinking water supply. Groundwater
is believed to be comparatively much clean and free from pollution than surface water [1]. But
expanded discharge of industrial effluents, domestic sewage use of fertilizers and pesticides, waste
deposit causes the groundwater to become polluted and creates health problems [10].
In developing countries contamination of water supplies by organic chemicals is lesser
concern, because most of the health problems are found to be associated with the presence of
inorganic chemicals and pathogenic organisms in drinking water. In Thanjavur region some of
ground water samples was contaminated, because in the presence of excess of calcium hardness,
magnesium hardness, TDS and total alkalinity [8].
The hard water is said to cause serious health problems such as urolithosis, cardiovascular
disorder, kidney problems and cancer [7]. Additionally, WHO reports that excess intake of calcium
is associate with kidney stones and that of magnesium leads to diarrhea and laxative effect due to
change in bowel habit. Water quality of Thiruvarur region most of the areas groundwater is not
suitable for drinking purpose, because in the presence of excess hardness [12; 3].
In view of the above aspects of groundwater contamination, the present study was undertaken
to investigate the possible impact on the groundwater quality of some bore wells of Kumbakonam
region in Thanjavur district. Thus, in this paper an attempt has been made to assess the physical and
chemical properties of groundwater.

2. MATERIALS AND METHODS

2.1 Study area:
Kumbakonam is located in Thanjavur district. The studies area lies at 110 38’ N and 750 45’ E
latitude. Fig – 1 showed the location of ground water samples was collected from Kumbakonam
region and table – 1 are given about sampling points of Kumbakonam region.

SciPress applies the CC-BY 4.0 license to works we publish: https://creativecommons.org/licenses/by/4.0/

2 Volume 59

Figure-1: Study Area

Table-1: Sampling points of Kumbakonam region
Sampling Point Sampling Point Number
Mangudi (East) S1
Mangudi (West) S2
Swamimalai (North) S3
Swamimalai (South ) S4
Kumbakonam S5
Baburajapuram S6
Dharasuram S7
Ariyapadaiyar S8

2.2. Methodology
Water samples were collected in previously sterilized poly ethylene plastic bottles with cap. The
sampling has been carried out in month of MAY - 2015. The samples in the canes (Bottle) were
kept in the refrigerator. The physicochemical parameters were determined by IS analytical method.
Table-2 is given about methods used for estimation of variation physicochemical parameters.
Table – 2: Methods used for estimation of variation physicochemical parameters.
Parameters Methods References
pH pH – Metric method IS : 3025 (Part II)
Odour Olfactory method IS : 3025 (Part 5)
Turbidity Nephelometric method IS : 3025 (Part 10)
Electrical Conductivity Conduct metric method IS 3025 : 1964
Total Dissolved Solid Gravimetric method IS : 3025 (Part 16)
Total Alkalinity Titrimetric method IS : 3025 (Part 23)
Chloride Argento metric method IS : 3025 (Part 32)
Sulphate Turbidity method IS : 3025 (Part 24)
 International Letters of Chemistry, Physics and Astronomy Vol. 59 3

Calcium EDTA Titrimetric method IS : 3025 (Part 40)

Magnesium EDTA Titrimetric method IS : 3025 (Part 46)
Nitrate Chromotropic acid method IS : 3025 (Part 34)
Nitrite Spectrometric method IS : 3025 (Part 34)
Phosphate Spectrometric method IS 3025 : 1964
Fluoride Zirconium alizarin method IS 3025 : 1964
Manganese Colour comparison method IS 3025 : 1964
Iron 1, 10, Phenanthroline method IS : 3025 (Part 53)

3. RESULTS AND DISCUSSION

The water samples were collected from various parts of Kumbakonam region, and were analyzed
for their physicochemical characteristics. The physicochemical parameters like TDS of water
samples was analyzed by gravimetric method, turbidity of the water samples was analyzed by
nephelo metric method, alkalinity, calcium, magnesium, chloride was estimated by titrimetric
method, and other parameters were analyzed by Indian standard methods. The results were
compared with BIS drinking water quality guideline. The estimated physicochemical parameters are
reported in the table- 3 and table- 4.

3.1. Appearance:
Colour of water may be due to the presence of fine particles in suspension (or) due to certain
mineral matter in solution. The entire collected sample had slightly yellow colour, (Table- 3).

3.2. Odour:
Organic and inorganic chemicals originating from domestic wastes and by decomposition of
vegetables matter contributes odour to the water. Entire collected ground water samples had odour
less nature, (Table- 3).

3.3. Turbitity:
Turbitity in natural water is caused by clay, organic matter, phytoplankton etc., and the turbidity
of ground water samples from Kumbakonam region ranged from 10 NTU to 55 NTU, the data are
shown in table- 3.

3.4. Electrical Conductivity:

Electrical conductivity is the capacity of water to convey current and this may be due to the
presence of soluble salts and ionic species which act as conducting medium. Conductivity of the
samples ranged between 550 µS/cm to 1790 µS/cm. The data are given in table- 3, (Fig- 2).

3.5. Total Dissolved Solids:

Many dissolved substance are undesirable in water. Dissolved minerals, gases and organic
constituents may produce aesthetically displeasing colour, taste and odour. The total dissolved
solids of Kumbakonam region ground water range between 385 mg/l to 1253 mg/l. The TDS of
ground water sample number S1, S3, S5, S6, S7 and S8 is high in Kumbakonam region, (Table - 3),
(Fig - 3). If the TDS of drinking water is more than 2000 mg/l, would result to affect gastro
intestinal irritation to human beings.

3.6. Hydrogen ion concentration (pH):

pH is the measure of capacity (or) alkalinity natural water is alkaline due to the presence of
carbonates. The desirable pH range for drinking water is 6.5 to 8.5. The water samples had pH
ranged from 6.8 to 7.2. All the samples pH lying with in BIS permissible limit, showing that all the
samples were almost neutral and harmless, (Table- 4), (Fig- 4).
4 Volume 59

3.7. Alkalinity:
Alkalinity in water is due to the presence of carbonates, bicarbonates and hydroxides.
Bicarbonates are the major contributes since they are included from the basic materials in the soil.
Alkalinity is also a measure of water to absorb H+ ions. Total alkalinity of the samples was found to
range from 212 mg/l to 460 mg/l, (Table- 4), (Fig- 5). The entire collected ground water samples
had total alkalinity lying above the BIS desirable limit.

3.8. Calcium:
The calcium hardness was recorded in 32 mg/l to 128 mg/l. Ground water sample number S7 and
S8 were exceeding the BIS limit. Excess calcium hardness of ground water samples causing kidney
problem, urolithosis, to human beings. The data are given in table- 4 and fig- 6.

3.9. Magnesium:
The magnesium hardness was recorded in 21 mg/l to 55 mg/l. The magnesium content of sample
numbers S1, S3, S5, S6, S7 and S8 from Kumbakonam region is above the BIS desirable limit,
(Table- 4), (Fig- 7).

3. 10. Iron:
Irons usually exist in ferrous and ferric forms. Generally, the ferric form is predominant in natural
water. Excess iron causes stripping of clothes. The samples had iron levels ranged between 0.30
mg/l to 1.47 mg/l, (Table- 4), (Fig- 8). The entire ground water samples of Kumbakonam region
iron content is above the BIS desirable limit.

3.11. Manganese;
Manganese was recorded in 0.33 mg/l to 3.36 mg/l. All the ground water samples of Kumbakonam
region the manganese content level is high compare than BIS desirable limit, (Table- 4), (Fig - 9).
Generally the manganese is non – toxic to animals. However, when exceed 100 ppm it cause
toxicity to human body and produces fever, muscular fatigue.

3.12. Nitrite:
Nitrite in water is due to incomplete oxidation of organic matter containing nitrogen. Nitrites
should never be present in drinking water. Nitrite of the samples was found to range from 0.09 mg/l
to 1.65 mg/l. The nitrite content of ground water sample number S1, S3 and S4 had high
concentration compare than BIS desirable limit. High concentration of nitrites may cause blue-baby
syndrome in children, (Table- 4), (Fig- 10)
3.13. Nitrate:
This is the highest oxidized form of Nitrogen. Biological oxidation of nitrogenous substance from
sewage is the main source of nitrate. All the samples were found to have nitrate concentration
ranging from 1mg/l to 8 mg/l. All the water samples had nitrate content lying within the BIS limit,
(Table- 4), (Fig- 11).

3.14. Chlorides:
Discharge of domestic sewage is the main source of chloride in water. The chloride content
estimated in the samples ranged between 44 mg/l – 284 mg/l, (Table- 4), (Fig- 12). The ground
water sample number S1, S7 and S8 have high concentration of chloride ions. An excess of chloride
ion react with organic matter in water and produces cancer – causing compounds.

3.15. Fluoride:
Industrial waste is the main source of fluoride. The fluoride content was recorded in 0.1 mg/l to
0.2 mg/l. An entire ground water samples had fluoride content lying well below the detectable limit,
(Table- 4), (Fig- 13).
 International Letters of Chemistry, Physics and Astronomy Vol. 59 5

3.16. Sulphate:
Sulphate occurs naturally in all kinds of water. Drainage wastes are the main source of high
sulphate concentration. Excess sodium and magnesium sulphate may cause cathartic action. The
samples had sulphate levels ranged between 3 mg/l to 75 mg/l. Entire collected ground water
samples lying within BIS limit, (Table- 4), (Fig- 14).

3.17. Phosphate:
Generally phosphate occurs in natural water as inorganic (or) organic phosphates. Domestic
sewage, agricultural effluents and detergents are the main source of phosphate in water. Excess
phosphate may lead to growth of unwanted algae. The sample had phosphate content ranged from
0.03 mg/l to 0.86 mg/l, (Table- 4), (Fig- 15).

TABLE – 3: Physical parameters of ground water collected from Kumbakonam region.

BIS
Parameters S1 S2 S3 S4 S5 S6 S7 S8 Desirable
limit

Slightly Slightly Slightly Slightly Slightly Slightly Slightly Slightly

Appearance -
Yellow Yellow Yellow Yellow Yellow Yellow Yellow Yellow

Odour Odour Odour Odour Odour Odour Odour Odour

Odour Agreeable
less less less less less less less less

Turbidity 20 50 35 30 10 45 45 55 2 NTU

EC 1280 550 725 690 780 735 1790 1770 -

TDS 896 385 508 483 546 515 1253 1239 500 mg/l

TDS = Total Dissolved Solids, EC = Electrical Conductance.

TABLE – 4: Chemical parameters of ground water collected from Kumbakonam region.

BIS
Parameters S1 S2 S3 S4 S5 S6 S7 S8 Desirable
limit
pH 6.9 6.9 7 7 7.2 7.1 6.8 6.9 6.5 – 8.5
Alkalinity 340 212 320 280 280 236 460 380 200 mg/l
Ca2+ 61 32 32 43 48 40 128 104 75 mg/l
2+
Mg 55 23 29 21 38 29 48 40 30 mg/l
3+
Fe 0.30 1.47 0.64 0.59 0.30 0.75 0.96 1.25 0.3 mg/l
Mn2+ 2.63 0.74 0.36 0.68 0.92 0.33 3.36 1.97 0.1 mg/l
NO2- 0.09 BDL 0.45 1.65 BDL BDL BDL BDL 0.02 mg/l
NO3- 7 4 4 2 1 5 7 8 45 mg/l
-
Cl 152 52 44 52 64 72 284 240 200 mg/l
-
F 0.2 0.1 0.1 0.2 0.1 0.2 BDL BDL 1.0 mg/l
SO42- 72 5 3 4 38 31 39 75 200 mg/l
PO43- 0.03 1.20 1.20 0.04 0.08 0.39 0.86 0.78 -
6 Volume 59

FIGURES

2000 1400
1800
1200
1600
Electrical Conductance µS/cm

1400 1000
1200

TDS in mg/l
800
1000
800 600
600 400
400
200
200
0 0
S1 S2 S3 S4 S5 S6 S7 S8 S1 S2 S3 S4 S5 S6 S7 S8
Sample Number Sample Number
Fig- 2: EC Variation of the Study area. Fig- 3: TDS Variation of the Study area.

7.3 500
450
7.2
400
7.1 350
300
Alkalinity

7
250
6.9
pH

200
6.8 150
100
6.7
50
6.6 0
S1 S2 S3 S4 S5 S6 S7 S8 S1 S2 S3 S4 S5 S6 S7 S8
Sample Number
Fig- 4: pH Variation of the Study area. Fig- 5: Total Alkalinity Variation of the Study area.

140 60

120 50
100
40
Magnesium in mg/l
Calcium in mg/l

80
30
60
20
40
10
20

0 0
S1 S2 S3 S4 S5 S6 S7 S8 S1 S2 S3 S4 S5 S6 S7 S8
Sample Number Sample Number
Fig- 6: Calcium Variation of the Study area Fig- 7: Magnesium Variation of the Study area
 International Letters of Chemistry, Physics and Astronomy Vol. 59 7

1.6 4
1.4 3.5
1.2 3

1 2.5
Iron in mg/l

Manganese in mg/l
0.8
1.5
0.6
1
0.4
0.5
0.2
0
0 S1 S2 S3 S4 S5 S6 S7 S8
S1 S2 S3 S4 S5 S6 S7 S8
Sample Number Sample Number
Fig- 8: Iron Variation of the Study area Fig- 9: Manganese Variation of the Study area

1.8 9
1.6 8
1.4 7
1.2 6
1 5
Nitrate in mg/l
Nitrite in mg/l

0.8 4
0.6 3
0.4
2
0.2
1
0
0
S1 S2 S3 S4 S5 S6 S7 S8
S1 S2 S3 S4 S5 S6 S7 S8
Samples Number Sample Number
Fig- 10: Nitrite Variation of the Study area Fig- 11: Nitrate Variation of the Study area

300 0.25

250 0.2
200
0.15
Chloride in mg/l

150
Fluoride in mg/l

0.1
100

50 0.05

0 0
S1 S2 S3 S4 S5 S6 S7 S8 S1 S2 S3 S4 S5 S6 S7 S8
Sample Number Sample Number
Fig-12: Chloride Variation of the Study area Fig- 13: Fluoride Variation of the Study area
8 Volume 59

80 1.4
70 1.2
60 1
50
0.8
Sulphate in mg/l

Phosphate in mg/l
40
0.6
30
0.4
20
10 0.2

0 0
S1 S2 S3 S4 S5 S6 S7 S8 S1 S2 S3 S4 S5 S6 S7 S8

Sample Number Sample Number

Fig- 14: Sulphate Variation of the Study area Fig- 15: Phosphate Variation of the Study area

CONCLUSION
The physicochemical analysis of water samples concluded that the water quality of
Kumbakonam region most of the areas groundwater is not suitable for drinking purpose, because in
the region ground water had excess of TDS, manganese, chloride and iron. So human being of that
region is suffering with various diseases such as gastro intestinal irritations and skin irritation.
Rainwater harvesting is one of the solution to minimize the heavy metals concentration in drinking
water.

References
[1] Akinbile, C. O., & Yusoff, M. S. Environmental impact of leachate pollution on groundwater
supplies in
Akure, Nigeria. International Journal of Environmental Science and Development, (2011), 2(1), 81-
89.
[2] D. Kannan, N. Mani. Mohamad faizal. K, Dharmambal. S. A comparative study of groundwater
from Papanasam and Orathanadu region of Thanjavur District, Tamilnadu(India), Int. Journal of
Chemistry Environment and Technology. (2013), 1(4), 54-63.
[3] D. Kannan, N. Mani, Thiyagarajan. S. Chemical analysis of ground water from various parts of
Thiruvarur and Nagapattinam District Tamilnadu, India. Journal of Der Chemica Sinica, (2014),
5(3), 83-91.
[4] IS: 3025(1964) Method of sampling and test (Physical and Chemical) for water used in
industry.
[5] IS: 3025-Methods of sampling and Test (Physical and Chemical) for water and waste water.
[6] Jain P.K. Hydro chemistry and ground water quality of singhari river basin Dist, Chatapur
(M.P.). Poll. Res., (1996), 15(4): 407 -409.
[7] Meena, K.S, Gunsaria, R.K. Meena, K, Kumar .N, Meena, P.L, The problem of hardness in
ground water of Deoli Tehsil (Tonk District) Rajasthan, Journal of current Chemical and
Pharmaceutical Science. (2011), Vol. 2(1): 50- 54.
[8] N. Mani, D. Kannan, Assessment of ground water quality in various parts of Thanjavur district,
Tamilnadu (India). Int. Letters of Chemistry, Physics and Astronomy, (2015), 4: 49 – 61.
 International Letters of Chemistry, Physics and Astronomy Vol. 59 9

[9] O.Akoto, J.Adiyiah, Chemical analysis of drinking water from some communities in the
BrongAhafo region. Int. J. Environ. Sci. Tech., (2007), 4 (2):211-214.
[10] Ramakrishnaiah C. R. et al. (2009). Assessment of Water Quality Index for the Groundwater in
Tumkur Taluk, Karnataka State, India. E-Journal of Chemistry, 6(2), 523-530.
http://dx.doi.org/10.1155/2009/757424.
[11] Saravanakumar. K, and Ranjithkumar. R. Analysis of water quality parameters of groundwater
near Ambatture industrial area, Tamilnadu India. Indian Journal of Science Technology, (2011),
4(5), 660-662.
[12] T. Mohana priya, D. Kannan, N. Mani. A comparative study on chemical analysis of ground
water from various parts of Thiruvarur district, Tamilnadu(India). Int. Journal of Chemical and
Pharmaceutical Analysis, (2014), Vol. 2(1), 58 – 64.
[13] WHO, 2011, Hardness in Drinking – Water Background Document for development of WHO:
Guideline for Drinking – Water quality, WHO press.