455D Crawler Loader Introduction

INTRODUCTION AND CUSTOMER INFORMATION
RIGHT-HAND VIEW OF 455D CRAWLER LOADER

(MANUFACTURED 1983-1985)
TO THE CUSTOMER
THE PART NUMBERS IN THIS PARTS CATALOG WERE CORRECT AT THE TIME YOUR CATALOG WAS
PUBLISHED. IT IS OUR POLICY TO CONSTANTLY IMPROVE OUR MACHINES AND, THEREFORE, PART
NUMBERS MAY CHANGE. WHEN ORDERING PARTS, VERIFY PART NUMBERS THROUGH YOUR DEALER’S
(SPECIFICATIONS AND DESIGN SUBJECT TO CHANGE WTHOUT NOTICE.)

SERIAL NUMBER LOCATION
EACH 455D CRAWLER LOADER HAS THREE SERIAL NUMBER PLATES: ONE FOR THE PRODUCT IDENTIFICATION
NUMBER, ONE FOR THE ENGINE AND ONE FOR THE TRANSMISSION.
THE PRODUCT IDENTIFICATION NUMBER PLATE IS LOCATED ON THE BATTERY BOX FRONT PLATE.
THE ENGINE SERIAL NUMBER PLATE IS LOCATED BELOW AND TO THE REAR OF THE FUEL PUMP MOUNTING
BOSS ON THE RIGHT SIDE OF THE CYLINDER BLOCK.
THE TRANSMISSION SERIAL NUMBER PLATE IS LOCATED ON THE UPPER LEFT-HAND SIDE OF THE
TRANSMISSION CASE NEAR THE REAR OF THE CASE.
LEFT SIDE, RIGHT SIDE, FRONT AND REAR OF THE CRAWLER LOADER ARE VIEWED BY FACING IN THE
DIRECTION OF CRAWLER LOADER FORWARD TRAVEL.
LEFT SIDE, RIGHT SIDE, FRONT AND REAR OF THE BACKHOE AND BACKHOE COMPONENTS ARE DETERMINED
WHEN SEATED IN THE BACKHOE OPERATING POSITION.
WHENEVER SERIAL NUMBERS ARE REQUIRED FOR WARRANTY CLAIMS OR CORRESPONDENCE PERTAINING
TO THIS PRODUCT, IT IS EXTREMELY IMPORTANT THAT ALL CHARACTERS BE FURNISHED. THIS POINT
CANNOT BE OVEREMPHASIZED.
PRODUCT IDENTIFICATION NUMBER
1. DESIGNATES CRAWLER LOADER MANUFACTURER TO - JOHN DEERE DUBUQUE WORKS

2. DESIGNATES CRAWLER LOADER MODEL 455D
3. DESIGNATES CRAWLER LOADER CONFIGURATION X
4. DESIGNATES CRAWLER LOADER SERIAL NUMBER 123456
5. DESIGNATES UNIT TYPE CRAWLER
ENGINE SERIAL NUMBER PLATE
(ENGINE SERIAL NO. 610652-621172) (MANUFACTURED 1983-1983)
1. DESIGNATES ENGINE MANUFACTURER T-JOHN DEERE DUBUQUE WORKS

2. DESIGNATES NUMBER OF CYLINDERS AND CUBIC 4219 (3588 CM3)
INCH DISPLACEMENT.
3. DESIGNATES FUEL TYPE OR SPECIAL CONDITION T-TURBOCHARGED DIESEL
4. DESIGNATES ENGINE SERIAL NUMBER 123456
5. DESIGNATES THE ENGINE APPLICATION AND 4219TT 03
FACTORY USER.
ENGINE SERIAL NUMBER PLATE
(ENGINE SERIAL NO. 100001- ) (MANUFACTURED 1983- )
1. DESIGNATES ENGINE MANUFACTURER T-JOHN DEERE DUBUQUE WORKS

2. DESIGNATES NUMBER OF CYLINDERS AND CUBIC 4219 (3588 CM3)
INCH DISPLACEMENT.
3. DESIGNATES FUEL TYPE OR SPECIAL CONDITION T-TURBOCHARGED DIESEL
4. DESIGNATES ENGINE SERIAL NUMBER 123456
5. DESIGNATES THE ENGINE APPLICATION AND 4219TT 03
FACTORY USER.
CRAWLER LOADER EQUIPMENT
THE 455D CRAWLER LOADER MAY BE EQUIPPED WITH A 3110 RIPPER, A 3600 LOG ARCH OR A 9300 BACKHOE.
FOR 3110 RIPPER SERVICE PARTS SEE PC-931, FOR 3600 LOG ARCH SERVICE PARTS SEE PC-591 AND FOR
9300 BACKHOE SERVICE PARTS SEE PC-1235.
SERIAL NUMBER LISTING INFORMATION
SERIAL NUMBER INFORMATION IS LISTED TO SHOW ON WHICH MACHINES EACH PART CAN BE USED; FOR
EXAMPLE:
- THE PART CAN BE USED ON ALL MACHINES.

000000- THE PART CAN BE USED ON ALL MACHINES BEGINNING WITH THE SERIAL NUMBER LISTED.
-000000 THE PART CAN BE USED ON ALL MACHINES UP TO AND INCLUDING THE SERIAL NUMBER
LISTED.
000000-000000 THE PART CAN BE USED ON ALL MACHINES BETWEEN AND INCLUDING THE SERIAL NUMBERS
LISTED.
WHEN XXXXXX’S ARE LISTED IN PLACE OF A SERIAL NUMBER, A SERIAL NUMBER CHANGE WAS MADE BUT THE
EXACT SERIAL NUMBER WAS NOT AVAILABLE WHEN THE CATALOG WAS PRODUCED.
DIRECTION ARROW
ARROWS ARE USED WITH ILLUSTRATIONS TO INDICATE THE FRONT OF THE UNIT. "RIGHT-HAND" AND "LEFT-
HAND" SIDES OF LOADER OR TRACTOR PARTS ARE DETERMINED BY FACING IN THE DIRECTION OF MACHINE
FORWARD TRAVEL.
EXCEPTION: FOR ALL BACKHOE PARTS, "RIGHT-HAND" AND"LEFT-HAND" SIDES, "FRONT" AND "REAR" ARE
DETERMINED WHEN SEATED FOR BACKHOE OPERATION.
BOX-ENCLOSED ILLUSTRATIONS
A KEY NUMBER, SHOWN IN THE PARTS LIST, IS ASSIGNED TO A BOX ENCLOSING ALL PARTS SOLD AS A
SERVICE ASSEMBLY.
BOLT AND CAP SCREW STRENGTH IDENTIFICATION
BOLTS AND CAP SCREWS REQUIRED TO HAVE HIGH-STRENGTH QUALITIES EQUIVALENT TO SAE GRADE 8 ARE
IDENTIFIED THROUGHOUT THIS CATALOG BY THE DESCRIPTION HS SAE 8. ALL STANDARD BOLTS AND CAP
SCREWS ARE SAE GRADE 5 OR LOWER.
COMPLETE GOODS LISTINGS
COMPLETE GOODS ARE LISTED IN BOLD FACE TYPE. ORDER SEPARATELY. DO NOT INCLUDE ON
REPLACEMENT PARTS ORDER.
SI UNITS OF MEASURE
METRIC DIMENSIONS ARE GIVEN, WHERE APPLICABLE, THROUGHOUT THIS PARTS CATALOG.
CHANGE INDICATOR LINE
CHANGES AFFECTING THE ORDERING OF PARTS ARE IDENTIFIED BY VERTICAL LINES MARKED IN THE LEFT-
HAND MARGIN OF REVISED PARTS LISTING IMAGES. A LINE IS ALSO AT THE LEFT-HAND EDGE OF THE SAME
PART NUMBER IN THE NUMERICAL INDEX TO SHOW THE LOCATION OF REVISED INFORMATION.
TRADEMARKS
THROUGHOUT THIS PARTS CATALOG, YOU WILL FIND THE MANUFACTURER’S TRADEMARKS. THE FOLLOWING
IS A LIST OF TRADEMARKS THAT ARE USED IN THIS PUBLICATION.
LOCTITE® IS A TRADEMARK OF LOCTITE CORPORATION.

455D Crawler Loader Introduction

Uploaded by

Copyright:

Available Formats

455D Crawler Loader Introduction

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

455D Crawler Loader Introduction

Uploaded by

Copyright:

Available Formats

INTRODUCTION AND CUSTOMER INFORMATION

RIGHT-HAND VIEW OF 455D CRAWLER LOADER

(SPECIFICATIONS AND DESIGN SUBJECT TO CHANGE WTHOUT NOTICE.)

PRODUCT IDENTIFICATION NUMBER

1. DESIGNATES CRAWLER LOADER MANUFACTURER TO - JOHN DEERE DUBUQUE WORKS

1. DESIGNATES ENGINE MANUFACTURER T-JOHN DEERE DUBUQUE WORKS

1. DESIGNATES ENGINE MANUFACTURER T-JOHN DEERE DUBUQUE WORKS

- THE PART CAN BE USED ON ALL MACHINES.

BOLT AND CAP SCREW STRENGTH IDENTIFICATION

COMPLETE GOODS LISTINGS

CHANGE INDICATOR LINE

LOCTITE® IS A TRADEMARK OF LOCTITE CORPORATION.

You might also like