Register your new Bosch now:

www.bosch-home.com/welcome

Dishwasher SM…
SB…

en Instruction manual
     5HVHWVHF
K

% K PLQ $ K
6WDUW

& 5HVHWVHF


   

















 en

Table of contents

8 Intended use . . . . . . . . . . . . . . 4 - Utensils . . . . . . . . . . . . . . . . . . . 13

( Safety instructions . . . . . . . . . . 4 Not suitable. . . . . . . . . . . . . . . . . .
Glass and utensil damage . . . . . .
.
.
. 13
. 13
Before you switch ON the Loading the dishwasher . . . . . . . . . . 14
appliance . . . . . . . . . . . . . . . . . . . . .5 Unloading the dishwasher . . . . . . . . 14
Delivery. . . . . . . . . . . . . . . . . . . . . . . .5 Cups and glasses . . . . . . . . . . . . . . . 14
Installation. . . . . . . . . . . . . . . . . . . . . .5 Pans . . . . . . . . . . . . . . . . . . . . . . . . . 15
In daily use . . . . . . . . . . . . . . . . . . . . .6 Cutlery basket. . . . . . . . . . . . . . . . . . 15
Door lock . . . . . . . . . . . . . . . . . . . . . .7 Etagere . . . . . . . . . . . . . . . . . . . . . . . 15
Button lock . . . . . . . . . . . . . . . . . . . . .7 Folding spikes . . . . . . . . . . . . . . . . . 16
Damage . . . . . . . . . . . . . . . . . . . . . . .7 Small accessories holder . . . . . . . . . 16
Disposal . . . . . . . . . . . . . . . . . . . . . . .7 Knife shelf . . . . . . . . . . . . . . . . . . . . . 16
7 Protection of the Adjusting the height of the basket . . 16
environment . . . . . . . . . . . . . . . . 9 . Detergent . . . . . . . . . . . . . . . . . 17
Packaging. . . . . . . . . . . . . . . . . . . . . . 9
Adding detergent . . . . . . . . . . . . . . . 18
Old appliances . . . . . . . . . . . . . . . . . . 9
Combination detergent . . . . . . . . . . . 19
* Getting to know your / Overview of programmes . . . . 20
appliance . . . . . . . . . . . . . . . . . . 9
Control panel . . . . . . . . . . . . . . . . . . . 9 Programme selection . . . . . . . . . . . . 21
Appliance interior . . . . . . . . . . . . . . . 10 Information for test institutes . . . . . . . 21
Overview of menu. . . . . . . . . . . . . . . 10 0 Additional options . . . . . . . . . . 21
+ Water softening Express Wash/ Speed Perfect
system/Special salt . . . . . . . . . 10 (VarioSpeed). . . . . . . . . . . . . . . . . . . 21
Setting . . . . . . . . . . . . . . . . . . . . . . . 10 Half load . . . . . . . . . . . . . . . . . . . . . . 21
Water hardness table . . . . . . . . . . . . 11 HygienePlus . . . . . . . . . . . . . . . . . . . 21
Using special salt . . . . . . . . . . . . . . . 11 Intensive zone . . . . . . . . . . . . . . . . . . 21
Detergents with salt component . . . . 11 Extra drying. . . . . . . . . . . . . . . . . . . . 21
Switching off water softening
system . . . . . . . . . . . . . . . . . . . . . . . 12

, Rinse aid . . . . . . . . . . . . . . . . . 12
Setting amount of rinse aid. . . . . . . . 13
Switching off rinse aid refill
indicator . . . . . . . . . . . . . . . . . . . . . . 13

3
en Intended use

1 Operating the appliance . . . . . 22 8 Intended use

Programme data. . . . . . . . . . . . . . . . 22 In
ten
du
se

Aqua sensor . . . . . . . . . . . . . . . . . . . 22 This appliance is intended for

Switching on the appliance. . . . . . . . 22 use in the home and
Remaining running time display . . . . 22 domestic environments.
Timer programming . . . . . . . . . . . . . 23
End of programme . . . . . . . . . . . . . . 23
Use the dishwasher only in
Switching off automatically
the home and only for its
after the end of the programme . . . . 23 designated purpose: for
Switching off the appliance. . . . . . . . 24 washing domestic dishes.
Interrupting the programme . . . . . . . 24 This appliance is intended for
Terminating the programme . . . . . . . 24 use up to a maximum altitude
Changing the programme. . . . . . . . . 24 of 4000 metres above sea
Intensive drying. . . . . . . . . . . . . . . . . 24 level.
2 Cleaning and maintenance . . . 25
Overall condition of the machine . . . 25
Special salt and rinse aid . . . . . .
Filters . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
. 25
. 26 ( Safety instructions
S
afetyinstructio
s
n

Spray arms . . . . . . . . . . . . . . . . . . . . 26
This appliance may be used by
3 Fault, what to do? . . . . . . . . . . 27 children over the age of 8 years
Waste water pump . . . . . . . . . . . . . . 27 old and by persons with
Fault table. . . . . . . . . . . . . . . . . . . . . 28 reduced physical, sensory or
mental capabilities or by
4 Customer service . . . . . . . . . . 36 persons with a lack of
experience or knowledge if they
5 Installation and connection . . 36 are supervised or are instructed
Product package . . . . . . . . . . . . . . . 36 by a person responsible for
Safety instructions. . . . . . . . . . . . . . . 36 their safety how to use the
Delivery. . . . . . . . . . . . . . . . . . . . . . . 37 appliance safely and have
Technical specifications . . . . . . . . . . 37 understood the associated
Installation. . . . . . . . . . . . . . . . . . . . . 37 hazards.
Waste-water connection . . . . . . . . . . 37 Children must not play with, on,
Drinking water connection . . . . . . . . 38 or around the appliance.
Warm water connection . . . . . . . . . . 38 Children must not clean the
Electrical connection. . . . . . . . . . . . . 39 appliance or carry out general
Removing the appliance . . . . . . . . . . 39
maintenance unless they are at
Transportation. . . . . . . . . . . . . . . . . . 40
Protection against frost
least 8 years old and are being
(Emptying the appliance) . . . . . . . . . 40 supervised.

4
 Safety instructions en

Keep children below the age of Installation

8 years old at a safe distance
from the appliance and power Following installation, ensure
cable. that the back
of the dishwasher is not
Before you switch ON the freely accessible (protection
appliance against contact due to hot
surface).
Please read the instructions for Install and connect
use and installation carefully. the appliance according
They contain important to the installation
information on how to install, and assembly instructions.
use and maintain the appliance. Prior to installation,
Retain all documents for later disconnect the dishwasher
use or for the subsequent from the power supply.
owner. Ensure that the protective
You can download the conductor system
instructions for use from our of the domestic supply has
website free of charge. The been correctly installed.
relevant Internet address can The electrical connection
be found overleaf on these conditions must correspond
instructions for use. with the specifications
on the dishwasher rating
Delivery plate 92.
If the power cord of this
1. Check the packaging and appliance is damaged,
dishwasher immediately for it must be replaced with
damage caused in transit. Do a particular power cord.
not switch on a damaged To prevent injury, the power
appliance, but contact your cord may be purchased from
supplier. customer service only.
2. Please dispose of the If the dishwasher is installed
packaging material in an in a high-sided unit, the unit
environmentally friendly must be secured properly.
manner.
3. Do not let children play with
packaging and its parts.
There is a risk of suffocation
from collapsible boxes and
film.

5
en Safety instructions

If the dishwasher is installed Do not install the appliance

below or above other near heat sources (radiators,
domestic appliances, follow heat storage tanks, cookers
the information for installation or other appliances which
in combination with generate heat) and do not
a dishwasher install under a hob.
in the installation instructions Please note that the
for the particular appliances. insulation material of the
Also follow the installation dishwasher power cord may
instructions for melt next to heat sources
the dishwasher to ensure (e.g. heating / hot water
that all appliances are installations) or hot appliance
operated safely. parts. Make sure that the
If there is no information or if power cord of the
the installation instructions dishwasher never comes into
do not include contact with heat sources or
the appropriate information, hot appliance parts.
contact the manufacturer After installing the appliance,
of these appliances ensure that the plug is easily
to ensure that accessible.
the dishwasher can be (See Electrical connection)
installed above or below Some models:
these appliances. The plastic housing on the
If you cannot obtain any water connection contains
information from an electric valve,
the manufacturer, you must the connecting cables
not install the dishwasher are in the supply hose.
above or below these Do not cut through this hose,
appliances. do not immerse the plastic
If you install a microwave housing in water.
oven above the dishwasher,
the microwave oven may be
damaged. In daily use
Install built-under Read and observe the safety
or integratable appliances information and instructions
only under continuous for use on the packaging
worktops which have been for cleaning and rinsing agents.
screwed to adjacent
cupboards to ensure stability.

6
 Safety instructions en

Childproof lock (door lock) * Do rlock Damage

The description of the The appliance may be
childproof lock is at the back in repaired and opened up by a
the envelope. technician only. To do this,
* depending on model disconnect the appliance
from the power supply. Pull
out the mains plug or switch
Childproof lock (button lock) Butonlock

off the fuse. Turn off the tap.

You can secure your appliance If the appliance is damaged,
from being unintentionally the especially the fascia (cracks,
programme terminated (e.g. holes, broken buttons), or the
improper operation by children). door function is impaired,
stop operating the appliance.
Activating the button lock: Pull out mains plug or switch
off fuse. Turn off tap, call
1. Start the required customer service.
programme.
2. Hold down the button + for
approx. 4 sec. until this ’– is Disposal
indicated on the digital 1. Make redundant appliances
display. unusable to prevent
If any button is pressed while subsequent accidents.
the programme is running, 2. Dispose of the appliance in a
this ’– is indicated on the n environmentally friendly
digital display. It is not possible manner.
to end (Reset) the programme.
Deactivating the button lock: m Warning
Risk of injury!
Hold down the button + for
approx. 4 sec. until the To prevent injuries, e.g.
display ’– goes out. caused by stumbling, open
When the programme ends the dishwasher only briefly
(‹:‹‹ on the digital display), the in order to load and unload
button lock is cancelled. If there the dishwasher.
is a power failure, the button Knives and other utensils
lock is retained. Whenever a with sharp points must be
programme is restarted, the placed in the cutlery basket
button lock must be reactivated. with the points
downwards or horizontally on
the knife shelf*.

7
en Safety instructions

Do not lean or sit Do not allow children to play

on the open door. with or operate
In the case of free-standing the appliance.
appliances, ensure that the Keep children away from
baskets are not overloaded. detergents and rinse aid.
If the appliance These may cause chemical
is not in a cavity and a side burns in the mouth, throat
panel is accessible, the door and eyes or asphyxiation.
hinge area must be covered Keep children away from
at the side open dishwasher. There may
for reasons of safety be small parts in the
(risk of injury). The covers dishwasher which children
are available as optional could swallow and the water
accessories from customer inside the dishwasher is not
service or specialist outlets. drinking water as it may
* depending on model contain detergent residue.
Ensure that children do not
m Warning place fingers in the tablet
collecting tray 12. Small
Risk of explosion! fingers could become
Do not add any solvents caught in the slots.
to the washing chamber. When opening and closing
Danger of explosion! the door on an eye-level
appliance, ensure that
m Warning children do not become
Risk of scalding! jammed or crushed between
Open the door carefully when the appliance door and the
the programme is still running. cupboard door below.
There is a risk of hot water Children could become
spraying out of the appliance. locked in the appliance
(danger of suffocation) or get
m Warning into another dangerous
situation.
Risks to children!
Redundant appliances: Pull
If fitted, use the childproof out the mains plug, sever
lock. An exact description and dispose of the power
can be cord. Destroy the door lock
found in the back of the enve so that the door can no
lope. longer be closed.

8
 Protection of the environment en

7 Protection of the * Getting to know your

Prtoectio
nofth
eenviro
nm
ent
environment G
ettin
gtok
wyo
o
n r ap
u lian
ce
appliance
Both the packaging of new appliances Diagrams of the control panel
and the old appliances themselves and the interior of the appliance can be
contain valuable raw materials found in the envelope at the front.
and recyclable materials. Individual positions are referred
Please dispose of the individual parts to in the text.
separated according to type.
Please ask your dealer or inquire at your Control panel
local authority about current means
of disposal.
( ON/OFF switch
0 Programme buttons **
Packaging
8 Door opener
All plastic parts of the appliance are @ Timer programming *
identified with internationally H Additional options **
standardised abbreviations (e.g. >PS< P START button
polystyrene). Therefore, plastic waste
can be sorted out when the appliance is X Display “Check water supply”
being disposed of. ` Salt refill indicator
Please follow the safety instructions h Rinse aid refill indicator
under “Delivery”. )" Digital display
* depending on model
Old appliances ** Number depending on model

Please follow the safety instructions

under “Disposal of your appliance”.
This appliance is labelled in
 accordance with European
Directive 2012/19/EU
concerning used electrical and
electronic appliances (waste
electrical and electronic
equipment - WEEE). The
guideline determines the
framework for the return and
recycling of used appliances as
applicable throughout the EU

9
en Water softening system/Special salt

Appliance interior
+ Water softening
1" Top basket Water so
ften
ignsy
stem
/S
ecial salt
p
system/Special salt
1* Knife shelf *
12 Tablet collecting tray To ensure good washing results,
the dishwasher requires soft water, i.e.
1: Top spray arm containing low amounts of lime,
1B Bottom spray arm otherwise white limescale will be
1J Dispenser for special salt deposited on the utensils and inner
1R Filters container.
1Z Cutlery basket Tap water above 1.2 mmol/l must be
softened. The water is softened with
1b Bottom basket special salt (regeneration
1j Dispenser for rinse aid salt) in the water softening
9" Detergent dispenser system of the dishwasher.
9* Lock for detergent dispenser The setting and therefore the required
92 Rating plate amount of salt
* depending on model depends on the degree of hardness of
your tap water (see table).

Overview of menu Setting

The settings can be found in the The amount of salt dispensed can be
individual chapters. set from •:‹‹ to •:‹ˆ.
• Water Hardness •:‹‹ - •:‹ˆ Salt is not required at the set value
š Intensive drying š:‹‹ - š:‹‚ •:‹‹.
§ Rinse aid §:‹‹ - §:‹‡ 1. Find out about the hardness value of
‘ Hot water ‘:‹‹ - ‘:‹‚* your tap water. Your water utility
company will help you with this.
˜ Automatic disconnection ˜:‹‹ - ˜:‹ƒ 2. Set value can be found in the water
* depending on model hardness table.
3. Close the door.
4. Switch on ON/OFF switch (.
5. Hold down programme button #
and press START button P until
•:‹.... is indicated on the digital
display.
6. Release both buttons.
The LED for button # flashes and
the digital display )" displays the
factory setting •:‹….

10
 Water softening system/Special salt en

To change the setting: Using special salt

1. Press programme button 3.
Each time the button is pressed, the Always refill with special salt
set value increases by one level; immediately before switching on the
when the value of •:‹ˆ has been appliance. This ensures that overrun
reached, the display jumps back special salt solution is immediately
to •:‹‹ (off). washed out and does not corrode the
2. Press START button P. rinsing tank.
The chosen setting has now been 1. Open the screw-type cap of the
stored. compartment 1J.
2. Fill the tank with water (only required
when switching on the appliance for
Water hardness table the first time).
3. Then add dishwasher salt (not table
:DWHU +DUGQHVV PPROO 6HWYDOXH salt or tablets).
KDUGQHVV UDQJH RQWKH The water is displaced and runs out.
YDOXH PDFKLQH
ƒ&ODUNH As soon as the salt refill indicator `
Ȣ VRIW Ȣ ‡¯¯ on the fascia is lit, top up the salt.
Ȣ VRIW Ȣ ‡¯³
Ȣ PHGLXP Ȣ ‡¯›
Ȣ PHGLXP Ȣ ‡¯´

Ȣ PHGLXP Ȣ ‡¯ž
Ȣ KDUG Ȣ ‡¯‚
Ȣ KDUG Ȣ ‡¯±
Ȣ KDUG Ȣ ‡¯Å

* depending on model

Using detergents with salt

component Det rgentswithsaltcompone t

If combined detergents with a salt

component are used, salt can usually be
omitted up to a water hardness of
21° dH (37° fH, 26° Clarke, 3.7 mmol/
l). If the water hardness is over 21° dH,
special salt must be used.

11
en Rinse aid

Switching off salt refill 1. Open the dispenser 1j by pressing

indicator/water softening and lifting the plate on the cover.
system Switchingof watersofteni gsy tem

If the salt refill indicator ` is impaired

(e.g. when using combined detergents
containing salt component), it can be
switched off. 2
Proceed as described under
“Adjusting the water softening
system” and set the value to •:‹‹. 1
The water softening system and salt
refill indicator are now switched off.
2. Carefully pour rinse aid up
m Caution to the max. mark in the filler opening.
Never fill the salt dispenser with
detergent. You will destroy the water
softening system.

, Rinse aid
R
in
seaid
PD[
As soon as the rinse-aid refill
indicator h is lit on the fascia, there
is still a rinse-aid reserve of 1-2 rinsing
processes. Refill with rinse aid. 3. Close cover until it clicks shut.
The rinse aid is required for stain-free 4. To prevent excessive foam formation
utensils and clear glasses. Use only during the next rinse cycle, remove
rinse aid for domestic dishwashers. any rinse aid which has run over with
a cloth.
Combined detergents with rinse-aid
component may be used up to a water
hardness of 21° dH (37° fH,
26° Clarke, 3.7 mmol/l) only. If
the water hardness is over 21° dH,
rinse aid must be used.

12
 Utensils en

Setting amount of rinse aid

- Utensils
Uten
sils

The amount of rinse aid can be set from

§:‹‹ to §:‹‡. Please set rinse aid on
§:‹† to obtain very good drying results Not suitable
(§:‹† is already set in factory).
Change this setting, only if streaks Cutlery and utensils made of wood.
(select lower setting) or water stains Delicate decorative glasses, craft
(select higher setting) are left on the and antique utensils. These decors
utensils. are not dishwasher-proof.
1. Close the door. Plastic parts not resistant to heat.
2. Switch on ON/OFF switch (. Copper and tin utensils.
3. Hold down programme button # Utensils which are soiled with ash,
and press START button P until wax, lubricating grease or ink.
•:‹.... is indicated on the digital Aluminium and silver parts have a
display. tendency to discolour and fade during
4. Release both buttons. the wash cycle. Even some types of
The LED for button # flashes and glass (e.g. crystal glass objects) may
the digital display )" displays the turn cloudy after many wash cycles.
factory setting •:‹….
5. Press programme button # until Glass and utensil damage
the factory set value §:‹† is
indicated on the digital display )". Causes:
To change the setting: Glass type and glass production
1. Press programme button 3. process.
Each time the button is pressed, the Chemical composition of the
set value increases by one level; detergent.
when the value of §:‹‡ has been Water temperature of the wash
reached, the display jumps back programme.
to §:‹‹ (off).
Recommendation:
2. Press START button P.
Use only glasses and porcelain
The set value is saved. which the manufacturer designates
as dishwasher-proof.
Switching off rinse aid refill Use a detergent which protects
indicator utensils.
Take glass and cutlery out of the
If the rinse-aid refill indicator h is dishwasher as soon as possible after
impaired (e.g. when using combined the programme ends.
detergents containing rinse aid
component), it can be switched off.
Proceed as described under “Setting
amount of rinse aid” and set the
value to §:‹‹.
The rinse aid refill indicator h is now
switched off.

13
en Utensils

Loading the dishwasher Cups and glasses

1. Remove large food remnants. It is Top basket 1"
not necessary to prerinse utensils
under running water.
2. Place the utensils so that
– they are secure and cannot tip
over.
– all utensils with their openings
face down.
– parts with curves or indentations
are at an angle, thereby allowing
water to drain.
– does not obstruct rotation of the
two spray arms 1: and 1B.
Very small utensils should not be
washed in the machine, as they may fall
out of the baskets.

Unloading the dishwasher Note

To prevent water from dripping off the Utensils must not be placed above the
upper basket onto the utensils in the tablet collecting tray 12. These may
lower basket, it is recommended block the lid of the detergent dispenser
to empty the appliance from the bottom and prevent it from opening fully.
up.
Hot utensils are sensitive to shock!
Therefore, when the programme ends,
leave the utensils to cool down in the
dishwasher until they can be handled.
Note
When the programme ends, water
droplets can still be seen inside
the appliance. This does not affect
the drying of the utensils.

14
 Utensils en

Pans Cutlery basket

Bottom basket 1b You should always place cutlery
unsorted with the points downwards.
To prevent injuries, place long, pointed
implements and knives on the knife
shelf.

Tip Etagere *
Etager

Heavily soiled utensils (pans) should The etagere and the space underneath
be placed in the bottom basket. The can be used for small cups and glasses
more powerful spray jet provides or for larger items of cutlery, such as
a better dishwashing result. wooden spoons or serving cutlery. The
Tip etagere can be folded up if not required.
Other examples, such as the best way
of loading your dishwasher, can CLICK
be found on our homepage as a free
download. The corresponding Internet
address can be found on the back page
of these instructions for use.

1
2
3

* Depending on the model, a 3-fold

height adjustment is possible. To do
this, first place the etagere vertically
and pull up, then place at a slight angle,
push down to the required height (1, 2,
or 3) and snap into place.

15
en Utensils

Foldingspikes Folding spikes * Knife shelf * Knifeshelf

* depending on model * depending on model

The spikes can be folded down to Long knives and other utensils can be
improve arrangement of pans, bowls arranged horizontally.
and glasses.

1 2

Adjusting the height of the

Adjustingtheheightofthebasket

Small accessories holder * Smal ac es oriesholder

basket *
* depending on model * depending on model
Light-weight plastic accessories, e.g. If required, the height of the upper
cups, lids, etc. can be held securely in utensils basket 1" can be adjusted to
the small accessories holder. provide more space for tall utensils
either in the upper or lower basket.
Appliance height 81.5 cm
Top basket Bottom
basket
Setting 1 max. ø 22 cm 30 cm
Setting 2 max. ø 24.5 cm 27.5 cm
Setting 3 max. ø 27 cm 25 cm
Appliance height 86.5 cm
Top basket Bottom
basket
Setting 1 max. ø 24 cm 33 cm
Setting 2 max. ø 26.5 cm 30.5 cm
Setting 3 max. ø 29 cm 28 cm

16
 Detergent en

Select one of the two following Top basket with upper and
procedures according to the design of lower roller pairs
the top basket for your appliance model:
1. Pull out the top basket 1" out.
Top basket with side levers 2. Remove the upper basket and re-
attach it to the upper (stage 3) or
1. Pull out the top basket 1" out. lower (stage 1) rollers.
2. To lower the basket, press in the left
and then the right lever on the
outside of the basket. In doing so,
hold the sides of the basket along
the upper edge to prevent it from
suddenly dropping.

. Detergent
D
eterg
en
t

You can use tablets as well as powder

or liquid detergents for dishwashers, but
never use washing-up liquid. The
3. To raise the basket, hold the basket dosage can be individually adjusted with
on the sides of the upper edge and powder or a liquid detergent according
lift it up. to the degree of soiling. Tablets contain
4. Before re-inserting the basket again, an adequately large amount of active
ensure that it is at the same height ingredients for all cleaning tasks.
on both sides. Otherwise, the Modern, powerful detergents
appliance door cannot be closed predominantly use a low-alkaline
and the upper spray arm will not be formulation with enzymes. Enzymes
connected to the water circuit. break down starch and remove protein.
To remove coloured stains (e.g. tea,
ketchup), oxygen-based bleaching
agents are generally used.

17
en Detergent

Note 2. Close the cover on the detergent

To ensure a good washing result, dispenser by sliding it up until the
always follow the instructions lock engages without difficulty.
on the detergent packaging!
If you have further questions,
we recommend that you contact &/,&.
the detergent manufacturers’ helpline.

m Warning – Read and observe the

safety information and instructions for
use on the packaging for cleaning and
rinsing agents.

Adding detergent
The detergent dispenser opens
1. If the detergent dispenser 9" is still automatically at the optimum time
closed, press the lock 9* to open depending on the programme.
the detergent dispenser. The powder or liquid detergent
Pour detergent into the dry detergent is distributed in the appliance and is
dispenser 9" only (insert tablet flat, dissolved, the tablet falls into
not on its edge). the tablet collecting tray where it
Dosage: see manufacturer’s dissolves in doses.
instructions on the packaging.
The graduated detergent Tip
dispenser 9" helps you add the If the utensils are only lightly soiled,
correct amount of powder or liquid slightly less than the indicated amount
detergent. of detergent is usually adequate.
Usually 20 ml–25 ml are adequate Suitable detergents and care products
for normal soiling. If using tablets, can be purchased online
one tablet is adequate. via our website or via customer service
50 ml (see back page).
25 ml
15 ml

18
 Detergent en

Combination detergent Notes

You will obtain optimum rinsing
Apart from conventional detergents and drying results by using solo
(Solo), a number of products are offered detergents and applying salt
with additional functions. These and rinse aid separately.
products contain not only the detergent If programmes are short, tablets
but also rinse-aid and salt replacement may not have full cleaning effect
substances (3in1) and, depending due to different dissolving properties
on the combination (4in1, 5in1, etc.), and there may even be undissolved
additional components such as glass detergent residue. It is
protection or stainless steel cleaner. recommended to use washing
Combination detergents function only powder for these programmes.
up to a specific degree of hardness The Intensive programme (on some
(usually 21°dH). Over this limit salt models) requires one tab only. When
and rinse-aid must be added. using washing powder, you can
As soon as combined detergents apply some of this cleaning agent
are used, the rinse programme to the inside of the appliance’s door.
is adjusted automatically to ensure Even if the rinse-aid and/or salt refill
the best possible rinsing and drying indicator is lit, the rinse programme
result. will run correctly with combined
detergents.
m Warning – Do not place small parts If using detergents in a water-soluble
for washing in the tablet collecting tray protective cover: Take hold of the
12; this prevents the tablet from cover with dry hands only and put
dissolving evenly. the detergent into an absolutely
dry detergent dispenser only,
m Warning – If you want to add more otherwise the detergent may stick.
utensils after the programme If you switch from combined
has started, do not use the tablet detergents to solo detergents,
collecting tray 12 as a handle ensure that the water softening
for the upper basket. The tablet could system and amount of rinse aid have
already be there and you will touch been set to the correct value.
the partially dissolved tablet.

19
en Overview of programmes

/ Overview of programmes
Overviewofrpogram
mes

The max. possible number of programmes is illustrated in this overview.

The corresponding programmes and their arrangement can be found on the
fascia.
Type of utensils Type of soiling Programme Possible Programme sequence
additional
options
Pre-rinse

±/° all
Clean 70°
Intermediate rinse
wok70° Final rinse 72°
pots and pans, very adhesive burned-
non-sensitive in or dried-on food Drying
utensils remnants containing Pre-rinse
and cutlery starch or protein
Ù/Ø all
Clean 65°
Intermediate rinse
Normal 65° Final rinse 65°
Drying

Á all
Is optimised according
to the soiling with the aid
Auto 45° - 65° of sensors.
part dried, common Prerinse
mixed utensils
and cutlery household food
remnants â/à all
Clean 50°
Intermediate rinse
Eco 50° Final rinse 65°
Drying
sensitive utensils,
cutlery,
temperature-
slightly adhesive, ñ/ð Extra drying
Clean 45°
Intermediate rinse
fresh food remnants Quick 45°
sensitive plastic Final rinse 55°
and glasses

all types cold rinsing, ù/ø none Prerinse

of utensils intermediate cleaning Prerinse

20
 Additional options en

Programme selection § Half load *

Half oad

You can select a suitable programme If you have only a few items to wash
according to the type of utensils and (e.g. glasses, cups, plates), you can
degree of soiling. switch to “half load”. This will save
water, energy and time. It is
recommended to put a little less
Information for test institutes detergent in the detergent dispenser
than for a full load.
Test institutes receive the information for
comparability tests (e.g. according to
EN60436). μ HygienePlus * Hygien Plus

These are the conditions for conducting

the tests, however these are not the This function increases the temperatures
results or consumption values. and retains them for an extra long time
to obtain a defined disinfection
Request by e-mail to: performance. Continuous use of this
[email protected] function increases the hygiene status.
The product number (E no.) and the This additional option is ideal for
production number (FD) are required cleaning e.g. chopping boards and baby
which you can find on the rating plate bottles.
92 on the appliance door.
Ï Intensive zone * Intensivezone

Perfect for a mixed load. You can wash

0 Additional options
Aditio
nalptoio
ns
very soiled pots and pans in the lower
basket together with normally soiled
utensils in the upper basket. The spray
* depending on model pressure in the lower basket is
Additional options can be set with intensified, the rinsing temperature is
the buttons H. increased slightly.

Expres Wash/Spe dPerfect(VarioSpe d) Ÿ Express Wash/ Speed ¿ Extra drying * Extradrying

Perfect/ (VarioSpeed) * An increased temperature during the

final rinse and an extended drying
This function can reduce the running phase ensure that even plastic parts dry
time by approx. 20% to 50% depending better. There is a slight increase in the
on the selected rinse programme. The energy consumption.
change in the running time is indicated
on the digital display )". To obtain
optimum cleaning results at a reduced
running time, water and energy
consumption are increased.

21
en Operating the appliance

Switching on the appliance

1 Operating
the appliance 1. Turn on the tap fully.
Operatin
gth
eapliance
2. Switch on ON/OFF switch (.
The Eco 50° programme display
Programme data flashes. This programme remains
selected if no other programme
The programme data (consumption button 0 is pressed. The expected
values) can be found in the summary of programme duration
instructions. They refer to normal flashes on the digital display )".
conditions and the water hardness set 3. Press the START button P.
value •:‹…. Different influencing factors The programme starts running.
such as e.g. water temperature or line
pressure may result in deviations. Note
- for environmentally friendly operation
Aqua sensor *
Aquasensor
of the dishwasher:
For ecological reasons the Eco 50°
* depending on model programme is preset whenever the
appliance starts. This conserves
The Aqua sensor is an optical environmental resources and not least
measuring device (light barrier) which saves you money.
measures the turbidity of the rinsing The Eco 50° programme is a
water. particularly environmentally friendly
The Aqua sensor is used according to programme. According to EU
the programme. If the Aqua sensor is regulation 1016/2010 it is the
active, “clean” rinsing water can be “Standard programme” which is the
transferred to the next rinse bath and most efficient standard cleaning cycle
water consumption can be reduced by for cleaning normally soiled utensils in
3–6 litres. If the turbidity is greater, the terms of the combined energy and
water is drained and is replaced with water consumption for cleaning these
fresh water. In the automatic types of utensils.
programmes the temperature and
running time can also be adjusted to the
degree of soiling. Remaining running time
display
When the programme is selected, the
remaining running time of the
programme is indicated on the digital
display )".
The running time is determined during
the programme by the water
temperature, the number of utensils as
well as the degree of soiling and may
vary (depending on the selected
programme).

22
 Operating the appliance en

Timerprogram ing Timer programming * Switching off automatically

after the end of
* depending on model the programme * Switchingof automaticalyafterthe ndoftheprogram e

You can delay the start of the

programme in 1-hour steps up to * depending on model
24 hours.
To save energy, the dishwasher is
1. Close the door. switched off 1 minute after the
2. Switch on ON/OFF switch (. programme ends (factory setting).
3. Press button @ + until the digital Automatic disconnection
display )" jumps to œ:‹‚. can be adjusted from ˜:‹‹ to ˜:‹ƒ.
4. Press @ + or – button until the ˜:‹‹ Appliance does not switch off
displayed time corresponds with your automatically
requirements.
˜:‹‚ Off after 1 min
5. Press START button P, timer
programming is activated. ˜:‹ƒ Off after 120 min
1. Close the door.
6. To delete timer programming, press
the @ + or – button until )" œ:‹‹ 2. Switch on ON/OFF switch (.
is indicated on the digital display. 3. Hold down programme button #
You can change your programme and press START button P
selection at any time until the until •:‹... is indicated on the digital
programme starts. display.
4. Release both buttons.
The LED for button # flashes and
End of programme the digital display )" displays the
factory setting •:‹….
The programme has ended when the 5. Press programme button # until
value ‹:‹‹ is indicated on the numerical the factory set value ˜:‹‚
display )". is indicated on the digital
display )".
To change the setting:
1. Press programme button 3.
Each time the button is pressed, the
set value increases by one level;
when the value of ˜:‹ƒ has been
reached, the display jumps back
to ˜:‹‹ (off).
2. Press START button P.
The set value is saved.

23
en Operating the appliance

Switching off the appliance Changing the programme

Short time after the end of the When the START button P has been
programme: pressed, the programme cannot be
1. Switch off ON/OFF switch (. changed.
2. Turn off the tap (not applicable if The only way a programme can be
Aqua-Stop fitted). changed is by Cancel programme
3. Remove the utensils when they have (Reset).
cooled down.
Note Intensive drying
When the programme ends, leave The final rinse uses a higher
the appliance to cool down a while temperature which improves the drying
before opening it. This will prevent result. The running time may increase
steam from escaping and causing long- slightly. (Caution if utensils are delicate!)
term damage to your built-in furniture.
1. Close the door.
2. Switch on ON/OFF switch (.
Interrupting the programme 3. Hold down programme button #
and press START button P until
1. Switch off ON/OFF switch (. the digital display )" •:‹... is
The LEDs go out. The programme is indicated.
saved. 4. Release both buttons.
If the door was opened on an The LED for button # flashes and
appliance which has a warm water the digital display )" displays the
connection or is heated, first leave factory setting •:‹….
the door ajar for several minutes and
then close. Otherwise, expansion 5. Press programme button # until
(pressure) may cause the appliance the factory set value š:‹‹ is
door to spring open or water to run indicated on the digital display )".
out of the appliance. To change the setting,
2. To continue the programme, switch 1. Press the button 3 to switch the
on the ON/OFF switch ( again. Intensive drying on š:‹‚ or off š:‹‹.
2. Press START button P.
Terminating the programme
Terminatingtheprogram e
The set value is saved.
(Reset)
1. Press START button P for
approx. 3 sec.
The numerical display )"
indicates ‹:‹‚.
2. The programme sequence lasts
approx. 1 min. On the digital
display )" is indicated ‹:‹‹.
3. Switch off ON/OFF switch (.

24
 Cleaning and maintenance en

Never use a steam cleaner to clean your

2 Cleaning and dishwasher. The manufacturer is not
maintenance liable for any consequential damage.
C
leaingnandm
aitnenace
Regularly wipe the front of the appliance
and fascia with a damp cloth; water
A regular inspection and maintenance and a little washing up liquid
of your machine will help to prevent are adequate. Do not use sponges with
faults. This saves time and prevents a rough surface or abrasive detergents,
problems. as these could scratch the surfaces.
Stainless steel appliances: To prevent
Overall condition corrosion, avoid using sponge cloths
of the machine or wash them out thoroughly several
times before using for the first time.
Check spray arm for grease
and limescale deposits. m Warning – Health hazard
If you find such deposits: Never use other domestic detergents,
e.g. containing chlorine!
Fill detergent dispenser with
detergent. Start the appliance without
utensils in the programme with Special salt and rinse aid
the highest rinsing temperature.
Clean the appliance with detergents/ Check the refill indicators ` and
appliance cleaners which h. If required, refill salt and/or
are particularly suitable for use with rinse aid.
dishwashers.
To extend the life of your appliance,
clean the appliance regularly with a
special dishwasher detergent.
To ensure that the door seal always
remains clean and hygienic, regularly
clean it with a damp cloth and a little
washing-up liquid.
If the appliance is switched off for
a prolonged period, leave the door
ajar to prevent the formation of
an unpleasant odour.

25
en Cleaning and maintenance

Filters Spray arms

The filters 1R keep large foreign Limescale and contaminants in the
objects in the rinsing water away from rinsing water may block nozzles and
the pump. These foreign objects may bearings on the spray arms 1: and
occasionally block the filters. 1B.
The filter system consists of a coarse 1. Check outlet nozzles on the spray
filter, a flat fine filter and a microfilter. arms for blockages.
1. After each washing cycle check the 2. Unscrew the upper spray arm 1:.
filters for residue. 3. Remove the lower spray arm 1B
2. Unscrew filter cylinder as illustrated upwards.
and take out filter system.




4. Clean spray arms under running

water.
5. Re-engage or screw on spray arms.

3. Remove any residue and clean filters

under running water.
4. Re-install filter system in reverse
sequence and ensure that the arrow
marks are opposite each other after
closing the filter system.

26
 Fault, what to do? en

In this case:
3 Fault, what to do?
Falut, whattodo?
1. First always disconnect
the appliance from the power supply.
Experience has shown that you can 2. Take out top basket 1" and bottom
rectify most faults which occur in daily basket 1b.
operation yourself. This ensures that 3. Remove the filters 1R.
the machine is quickly available to you
again. In the following overview you can 4. Scoop out water, use a sponge if
find possible causes of malfunctions required.
and helpful information for rectifying 5. Prise out the white pump cover
them. (as illustrated) using a spoon. Grip
the cover on the crosspiece and lift
Note diagonally inwards. Remove cover
If the appliance stops during completely.
dishwashing or does not start for no
obvious reason, first run the Abort
programme function (Reset).
(See chapter entitled “Operating
the appliance”)
1
m Warning – Don’t forget: Repairs may
be carried out by technicians only. If a
component has to be replaced, ensure
that only original spare parts are used.
Improper repairs or use of non-original
spare parts may cause considerable
damage and put the user at 6. Check impeller wheel and remove
considerable risk. any foreign objects.
7. Place cover in the original position
Waste water pump and press down until it engages
(click).
Large food remnants or foreign objects
which were not captured by the filters
may block the waste water pump. The
rinsing water will then be above 2 3
the filter.

m Warning – Risk of cuts!

When cleaning the waste water pump,
ensure that you do not injure yourself
&/,&.
on pieces of broken glass or pointed
implements.
8. Install filters.
9. Re-insert baskets.

27
en Fault, what to do?

Fault table

Fault Cause Remedial action

“Check water supply” Supply hose kinked. Install supply hose without kinks.
display X lights up. Tap turned off. Turn on the tap.
Tap jammed or calcified. Turn on the tap.
Flow rate must be min. 10 l/min.
when water supply is open.
Filter in the water supply blocked. Switch off the appliance and pull out
the mains plug. Turn off the tap. Unscrew
water connection.

Clean filter in the supply hose. Screw water

connection on again. Check for leaks.
Reconnect power supply. Switch on
the appliance.
Error code “:‹ˆ is lit. Intake opening (on right inside of Arrange utensils so that the intake opening
appliance) covered by utensils. is not obstructed.
Error code “:‚ƒ is lit. Heating element calcified or Clean appliance with dishwasher cleaning
soiled. agent or descaler. Operate the dishwasher
with water softening system and check the
setting (see chapter “Water softening
system/Special salt”).
Fault code “:‚… is lit. Water protection system Turn off tap.
Fault code “:‚† is lit. activated. Call customer service and mention the fault
Fault code “:‚‡ is lit. Constant water inflow. code.
Error code “:ƒƒ is lit. Filters 1R are soiled or Clean filters.
blocked. (See Cleaning and maintenance)
Error code “:ƒ… is lit. Waste water hose Install hose without kinks, remove any
is blocked or kinked. residue.
Siphon connection still sealed. Check connection to siphon and open if
required.
Cover on the waste water pump Lock cover correctly.
loose. (See Waste water pump)

28
 Fault, what to do? en

Fault Cause Remedial action

Error code “:ƒ† is lit. Waste water pump blocked Clean pump and lock cover correctly. (See
or cover on the waste water Waste water pump)
pump is not locked in position.
Error code “:ƒˆ is lit. Mains voltage too low. Not an appliance fault, have the mains
voltage and electrical installation checked.
A different error code is A technical fault has probably Switch off appliances with the ON/OFF
indicated on the digital occurred. switch (. After a short time restart
display. the appliance.
(“:‹‚ to “:„‹) If the problem recurs, turn off the tap and
pull out the mains plug.
Call customer service and mention the error
code.
Display flashes Door not closed properly. Close the door. Ensure that no objects
(utensil, fragrance dispenser) are protruding
over the basket and preventing the door
from closing.
Pause function activated. * Press the Start button again to continue the
rinse programme. *
Refill indicator for salt ` No rinse aid. Refill rinse aid.
and/or rinse-aid h is lit. No salt. Refill with special salt.
Sensor does not detect salt Use different special salt.
tablets.
Refill indicator for salt ` Refill indicator switched off. Activation/deactivation (see chapter Water
and/or rinse-aid h softening system/Special salt or Rinse aid).
is not lit. There is still enough special salt/ Check refill indicator, levels.
rinse aid available.
Water is left Filter system or area under Clean filters and area underneath (see
in the appliance at the end the filters 1R is blocked. Waste water pump).
of the programme. The programme has not yet Wait until programme ends or reset (see
ended. Terminating the programme).

29
en Fault, what to do?

Fault Cause Remedial action

Utensils not dry. No or too little rinse aid Refill rinse aid.
in the dispenser.
Programme selected without Select programme with drying (see
drying. Overview of programmes, Programme
sequence).
Water collecting in depressions Arrange utensils in a sloping position,
on the utensils and cutlery. arrange affected utensils as sloping
as possible.

The combined detergent used Use different combination detergent with

has a poor drying performance. better drying performance. Use of rinse aid
also increases the drying performance.
Intensive drying to increase Activate intensive drying (see Operating
drying not activated. the appliance)
Utensils were removed too early Wait until program ends or wait until 30 min
or drying process had not ended after program ends before removing
yet. utensils.
The eco rinse aid used has a poor Use a proprietary rinse aid. Eco products are
drying performance. much less effective.
Plastic utensils not dry. Special properties of plastic. Plastic has a lower heat storage capacity
and therefore dries less well.
Cutlery not dry. Cutlery not arranged properly Separate cutlery if possible, prevent contact
in the cutlery basket. points.
Cutlery not arranged properly Arrange cutlery properly and separate if
in the cutlery drawer. possible.
Appliance interior wet after No appliance fault. On account of the “Condensation drying”
rinse cycle. principle, water droplets are physically
induced and required in the container. The
humidity in the air condenses on the inner
walls of the dishwasher, drains and is
pumped out.

30
 Fault, what to do? en

Fault Cause Remedial action

Food remnants Utensils placed too closely Arrange utensils with adequate clearance
on the utensils. together, utensils basket between them ensuring that the spray jets
overfilled. can reach the surface of the utensils.
Prevent contact points.
Spray arm rotation obstructed. Arrange utensils so that the spray arm can
rotate without obstruction.
Spray arm nozzles blocked. Clean the spray arm nozzles,
(See Cleaning and maintenance).
Filters 1R dirty. Clean filters, (see Cleaning and
maintenance).
Filters 1R inserted incorrectly Insert and engage filters correctly.
and/or not engaged.
Rinse programme too weak. Select a more intensive rinse programme.
Utensils precleaned too intensely; Do not prerinse utensils. Remove only large
sensors therefore decide on food remnants.
weak programme sequence. Recommended programme Eco 50° or
Stubborn soiling cannot be Intensive.
completely removed.
Tall narrow receptacles in corner
Do not place hollow receptacles too
areas are not rinsed adequately.obliquely and do not place in the corner
area.
Top basket 1" on right and left Set top basket to same height using side
not set to same height. levers.
Food remnants on the Dishes added too late. Only interrupt the rinse programme in the
dishes when pause initial phase to add more dishes.
function is used. *
Detergent residue Detergent dispenser cover Detergent dispenser cover must not be
blocked by utensils and therefore obstructed by utensils.
does not open fully. Do not place utensils or fragrance dispenser
in the tablet collecting tray.
Detergent dispenser cover Tablet must be inserted flat and not upright.
blocked by the tablet.
Tablets used in the quick or short Dissolving time of tablets too long for
programme. a quick or short programme.
Dissolving time of the detergent Use a detergent powder or select a more
is not reached in the selected intensive programme.
short programme.
Washing effect and dissolving Change detergent.
performance are reduced after
a prolonged storage time or
detergent is very lumpy.

31
en Fault, what to do?

Fault Cause Remedial action

Water stains on plastic Droplet formation on plastic Use a more intensive programme (more
parts surface is physically unavoidable. water changes).
After drying, water stains are Arrange utensils in a sloping position.
visible.
Use rinse aid.
If required, increase softening setting.
Washable or water-soluble Detergent substances are Change detergent brand.
coatings in the container or deposited. These coatings cannot Clean appliance mechanically.
on the door. usually be removed with
chemicals (appliance cleaner, ...).
If there is a “white coating” on Increase softening setting and change
the container floor, the water detergent if required.
softening system has been set
marginally.
Salt dispenser cover 1J not Close salt dispenser cover correctly.
closed.
Only for glasses: Initial glass See Glass and utensil damage.
corrosion – can only apparently
be wiped off.
White, stubborn coatings; Detergent substances are Change detergent brand.
limescale on the utensils, deposited. These coatings cannot Clean appliance mechanically.
container or door. usually be removed with
chemicals (appliance cleaner, ...).
Hardness range incorrectly set or Set water softening system according
water hardness greater than to instructions for use or top up salt.
8.9 mmol/l.
3 in 1 detergent or bio/eco Set water softening system according
detergent not effective enough. to instructions for use or use separate
detergents (proprietary detergent, salt, rinse
aid).
Underdosing of detergent. Increase detergent dosage or change
detergent.
Too weak rinse programme Select a more intensive rinse programme.
selected.
Tea or lipstick residue on Too low rinsing temperature. Select programme with higher washing
the utensils. temperature.
Too little or unsuitable detergent. Use suitable detergent at correct dosage.
Utensils precleaned too intensely; Do not prerinse utensils. Remove only large
sensors therefore decide on food remnants.
weak programme sequence. Recommended programme Eco 50°
Stubborn soiling cannot be
completely removed.

32
 Fault, what to do? en

Fault Cause Remedial action

Coloured (blue, yellow, Film formation consisting Can be partly removed with machine
brown), difficult to remove of ingredients from vegetables cleaner or by mechanical cleaning. Coatings
to non-removable coatings (e.g. cabbage, celery, potatoes, are harmless.
in the appliance or on noodles, ...) or the tap water (e.g.
stainless steel utensils. manganese).
Film formation caused by metallic Can be partly removed with machine
components on silver or cleaner or by mechanical cleaning.
aluminium utensils.
Coloured (yellow, orange, Film formation consisting Check function of the water softening
brown), easily removable of ingredients from food system (refill with salt) or, if using combined
deposits inside remnants and substances from detergents (tablets), activate water
the appliance (mainly the tap water (limescale), “soapy” softening system (see chapter Water
in the floor area) softening system/Special salt)
Discolouration of the Plastic parts inside the appliance Discolouration is normal and will not impair
plastic parts inside the may become discoloured during the function of the dishwasher.
appliance. the service life of the dishwasher.
Plastic parts discoloured. Too low rinsing temperature. Select programme with higher washing
temperature.
Utensils precleaned too intensely; Do not prerinse utensils. Remove only large
sensors therefore decide on food remnants.
weak programme sequence. Recommended programme Eco 50°
Stubborn soiling cannot be
completely removed.
Removable streaks on Too much rinse aid. Set rinse aid amount to lower setting.
glasses, glasses with No rinse aid added or setting too Add rinse aid and check dosage
metallic appearance and low. (recommended setting 4-5).
cutlery.
Detergent residue in the final Detergent dispenser cover must not be
rinse programme section. obstructed by utensils.
Detergent dispenser cover Do not place utensils or fragrance dispenser
blocked by utensils (cover does in the tablet collecting tray.
not open fully).
Utensils precleaned too intensely; Do not prerinse utensils. Remove only large
sensors therefore decide on food remnants.
weak programme sequence. Recommended programme Eco 50°
Stubborn soiling cannot be
completely removed.

33
en Fault, what to do?

Fault Cause Remedial action

Initial or existing, Glasses not dishwasher-proof, Use dishwasher-proof glasses.
irreversible clouding only suitable for dishwasher. Avoid long steam phase (standing time after
of glass. wash cycle ends).
Use wash cycle at lower temperature.
Set water softening system according to the
water hardness (if required one setting
lower).
Use detergent with glass protection
component.
Rust spots on the cutlery. Cutlery not adequately rust- Use corrosion-resistant cutlery.
resistant. Knife blades are
frequently more severely
affected.
Cutlery will also rust if rusting Do not wash rusting parts.
parts are rinsed at the same time
(pan handles, damaged utensil
baskets, etc.).
Salt content in the rinsing water Fasten salt dispenser lock firmly or remove
too high, as salt dispenser lock spilled salt.
not fastened firmly or salt was
spilled while being refilled.
The appliance does not The mains fuse has tripped. Check mains fuse.
start. Power cord not inserted. Ensure that the power cord is plugged all
the way into the back of the appliance and
into the socket. Check that the socket
functions.
The appliance door has not been Close the door.
shut properly.
Pause function is active. * Press the Start button P. *
Programme starts You did not wait until programme Perform reset.
automatically. ended. (See Terminating the programme).
Appliance cannot be set Appliance is in the programme. Perform reset (see Terminating
(hardness, final rinse, ...). Appliance can be set at the start the programme) and set the appliance
of the programme only. according to the instructions for use.
The door is difficult Child-proof lock is activated. Deactivate childproof lock. (See instructions
to open. for use at the back)
Door cannot be closed. Door lock has been activated. Close door with increased force.
Door cannot be closed due to Check appliance installation: Door or
installation. attached parts must close without
obstruction.

34
 Fault, what to do? en

Fault Cause Remedial action

Cover on the detergent Detergent dispenser or cover Remove detergent residue.
dispenser cannot be guide blocked by sticky detergent
closed. residue.
Detergent residue Spray arms blocked by utensils, Ensure that the spray arms can rotate freely.
in the detergent dispenser therefore detergent is not rinsed
or in the tablet collecting out.
tray. The detergent dispenser was Pour detergent into the dry detergent
damp when filled. dispenser only.
Appliance stops Door not closed properly. Close the door.
in the programme or Do not place utensils or fragrance Check whether rear panel is being pressed
programme is interrupted. dispenser in the tablet collecting in, e.g. by socket or by hose holder which
tray. has not been removed.
Top basket presses against inner
door and prevents door from
being closed securely.
Power and/or water supply Restore power and/or water supply.
interrupted.
Filling valves making Depends on domestic installation, No remedial action possible.
striking noises. as appliance is not defective. No
effect on appliance function.
Knocking or rattling noise. Spray arm strikes the utensils, Position utensils so that the spray arms do
utensils not positioned correctly. not strike the utensils.
If there is a low load, the water Load the appliance with more utensils or
jets strike the washing tank distribute the utensils more evenly
directly. in the dishwasher.
Light utensils move during Arrange light utensils securely.
the wash cycle.
Unusual foam formation. Handwash liquid in the rinse aid Immediately refill rinse aid dispenser with
dispenser. rinse aid.
Rinse aid spilled. Remove rinse aid with a cloth.

* depending on model

35
en Customer service

4 Customer service 5 Installation and

connection
Custo
merservice

If you are unable to rectify the fault, In

stallatio
nan
dco
ectio
n n

please contact your customer service.

The dishwasher must be connected
We always find a suitable solution, even
correctly, otherwise it will not function
to avoid unnecessary visits
properly. The specifications for the inlet
by technicians. Contact information
and outlet as well as the electrical
for your nearest customer service can
connected loads must correspond with
be found on the back of these
the required criteria as
instructions for use or on the enclosed
specified in the following paragraphs
customer service list. When calling,
or in the installation instructions.
please state the appliance number (E-
Nr. = 1) and the production number Install the appliance in the correct
(FD = 2) which can be found on the sequence:
rating plate 92 on the appliance door. 1. Checking appliance on delivery
2. Installing the appliance
3. Waste water connection
(1U )'
4. Drinking water connection
5. Electrical connection
 

Rely on the competence of the manufa Product package

cturer. Contact us. You can therefore be
sure that the repair is carried out If you have any complaints, contact
by trained service technicians who carry the dealer where you purchased
original spare parts for your domestic the appliance or our customer service.
appliances. Dishwasher
Instructions for use
Installation instructions
Warranty*
Installation materials
Steam guard plate*
Rubber apron*
Power cord
* depending on model

Safety instructions
Please follow the safety instructions
under “Installation”.

36
 Installation and connection en

Delivery Installation
Your dishwasher has been checked The required installation dimensions can
thoroughly in the factory to ensure that it be found in the installation instructions.
is in working order. This may cause Level the appliance with the aid of the
small water stains. These will disappear height-adjustable feet. Ensure that the
after the first wash cycle. appliance is situated securely on the
floor.
Technical specifications A built-under or integrated appliance
which is installed subsequently as a
free-standing appliance must be
Weight: secured to prevent it from
max. 60 kg overturning, e.g. by screwing it to the
Voltage: wall or by installing it under
a continuous worktop which is
220–240 V, 50 Hz or 60 Hz
screwed to adjacent cupboards.
Connected load: The appliance can easily be
2000–2400 W installed in a fitted kitchen between
Fuse: wooden and plastic walls.
10/16 A (UK 13A)
Power input: Waste-water connection
off mode (Po)* 0.10 W
1. The required work sequence can be
left on mode (Pl)* 0.10 W
found in the installation instructions.
*according to regulations (EU) nos. If required, fit a siphon with an
1016/2010 and 1059/2010 drainage connection.
Additional functions and settings may 2. Connect the waste-water hose to the
increase the power input. drainage connection of the siphon
Water pressure: with the enclosed parts.
at least 0.05 MPa (0.5 bar), maximum Ensure that the drainage hose is not
1 MPa (10 bar). At a higher water kinked, crushed or twisted and that
pressure: connect pressure-reducing there is no cover plate in the
valve ahead. drainage to prevent the waste water
from flowing out!
Inlet rate:
minimum 10 litres/minute
Water temperature:
cold water; hot water max. temperature
60 °C.
Capacity:
12–15 place settings (depending
on model).

37
en Installation and connection

Drinking water connection Warm water connection * Warmwatercon ection

1. Fasten the drinking water connection * depending on model

to the tap according The dishwasher can be connected
to the installation instructions using to cold or hot water up to max. 60 °C.
the enclosed parts.
Connection to hot water
Ensure that the drinking water is recommended if the hot water can be
connection is not kinked, crushed supplied by energetically favourable
or twisted. means and from a suitable installation,
2. When replacing the appliance, e.g. solar heating system with circulation
always use a new water supply hose. line.
Water pressure: This will save energy and time.
At least 0.05 MPa (0.5 bar), maximum The hot water setting ‘:‹‚ allows you
1 MPa (10 bar). At a higher water to adjust your appliance optimally
pressure: connect pressure-reducing to operation with hot water.
valve ahead.
It is recommended to have a water
Inlet rate: temperature (temperature of the
Minimum 10 litres/minute incoming water) of at least 40 °C
Water temperature: and no more than 60 °C.
Cold water; hot water max. temperature It is not recommended to connect
60 °C. the appliance to hot water if the water
is supplied from an electric boiler.
Setting hot water:
1. Close the door.
2. Switch on ON/OFF switch (.
3. Hold down programme button #
and press START button P
until •:‹... is indicated on the digital
display.
4. Release both buttons.
The LED for button # flashes and
the digital display )" displays the
factory setting •:‹….
5. Press programme button # until
the factory set value ‘:‹‹
is indicated on the digital
display )".
To change the setting:
1. By pressing the 3 button, you can
switch the hot water setting off ‘:‹‹
or on ‘:‹‚.
2. Press START button P.
The set value is saved.

38
 Installation and connection en

Electrical connection Removing the appliance

Connect the appliance to an Also observe
alternating current only, ranging from the sequence of worksteps here.
220 V to 240 V and 50 Hz or 60 Hz 1. Disconnect the appliance from
via a correctly installed socket with the power supply.
protective earth conductor. See
2. Turn off the water supply.
rating plate for required fusing 92.
3. Undo the waste water and drinking
The socket must be near
water connection.
the appliance and freely accessible
following installation. 4. Loosen fastening screws for
the furniture parts.
If the plug is not freely accessible, an
allpole disconnector with a contact 5. If fitted, remove the base panel.
opening of at least 3 mm must be 6. Pull out the appliance, carefully
fitted on the installation side pulling the hose behind.
to satisfy the relevant safety
instructions.
The connection may be modified by
technicians only.
A power cord extension may be
purchased from customer service
only.
Use only a residual current operated
circuit-breaker which features
the symbol ‚. Only this extension
guarantees compliance with
the currently valid regulations.
The appliance features a water
damage protection system. Please
note the system will not function
unless the power supply
is connected.

39
en Installation and connection

Transportation Protection against frost Protectionag instfrost(Emptyingtheap liance)

Empty the dishwasher and secure loose If the appliance is in a room where there
parts. is a risk of frost (e.g. holiday home),
Drain the appliance according to the empty the appliance completely (see
following steps: Transportation).
1. Turn on the tap.
2. Close the door.
3. Switch on ON/OFF switch (.
4. Select programme with the highest
temperature.
The expected programme duration is
indicated on the numerical display
)".
5. Press START button P.
Programme sequence starts.
6. After approx. 4 minutes press the
START button P until ‹:‹‚ is
indicated on the digital display.
After approx. 1 min ‹:‹‹ is indicated
on the digital display .
7. Switch off ON/OFF switch (.
8. Turn off the tap, disconnect supply
hose and drain water.
Transport appliance upright only.
(This prevents residual water from
running into the machine control and
damaging the programme sequence.)

6XEMHFWWRFKDQJHV

40
&KLOGSURRIORFNGRRUORFN

 :DUQLQJ
$FWLYDWHWKHFKLOGSURRIORFN $OZD\VFORVHWKHDSSOLDQFHGRRUFRPSOHWHO\
2SHQWKHGRRUZLWKDFWLYDWHG ZKHQ\RXOHDYHWKHDSSOLDQFH
FKLOGSURRIORFN 7KLVLVWKHRQO\ZD\\RXFDQSURWHFW\RXU
'HDFWLYDWHFKLOGSURRIORFN FKLOGUHQIURPSRWHQWLDOGDQJHUV

%DNLQJVKHHWVSUD\KHDG

/DUJHVKHHWVRUJULOOHVDQGSODWHVZKLFKKDYHDGLDPHWHUJUHDWHUWKDQFPJRXUPHW
SODWHVSDVWDSODWHVGLQQHUSODWHVFDQEHFOHDQHGZLWKWKHDLGRIWKHVSUD\KHDG
7RGRWKLVUHPRYHWKHWRSEDVNHWDQGLQVHUWWKHVSUD\KHDGDVLOOXVWUDWHGLQWKHGLDJUDP

7RHQVXUHWKDWWKHVSUD\MHWFDQUHDFKDOOSDUWVDUUDQJHWKHEDNLQJVKHHWVDVLOOXVWUDWHG
PD[âEDNLQJVKHHWVDQGâJULOOHV
1HYHURSHUDWHWKHGLVKZDVKHUZLWKRXWWKHWRSEDVNHWRUEDNLQJVKHHWVSUD\KHDG

VRPHPRGHOV
AquaStop guarantee (does not apply to appliances without AquaStop)

In addition to warranty claims against the seller based on the purchase contract
and in addition to our appliance warranty we will pay damages under
the following conditions:

1. If our AquaStop system is defective and causes water damage,

we will make good the damage for private users.
To ensure water damage protection, the appliance must be connected
to the power supply.
2. This liability guarantee is valid for the service life of the appliance.
3. A prerequisite for the warranty claim is that the appliance has been correctly
installed and connected with AquaStop according to our instructions.
This also includes the correct installation of the AquaStop extension
(original accessory). Our warranty does not extend to defective
feed lines or fittings up to the AquaStop connection on the tap.
4. If your appliance is fitted with AquaStop, you can leave your appliance
unattended during operation and leave the tap turned on afterwards.
The tap should only be turned off if you are absent from home for
a prolonged period, e.g. several weeks holiday.

Repair order and advice on faults.

GB 0344 892 8979 Calls from a BT landline will be charged at up to 3 pence per minute.
A call set-up fee of up to 6 pence may apply.
IE 01450 2655 0.03 € per minute at peak. Off peak 0.0088 € per minute.
US 800 944 2904 toll-free

Contact information for all countries can be found on the enclosed customer service list.

Robert Bosch Hausgeräte GmbH

Carl-Wery-Straße 34
81739 München
Germany
www.bosch-home.com

*9001007960*
9001007960 en (9710) 640MA