INTERNATIONAL ISO

STANDARD 261

Second edition
1998-12-15

ISO general purpose metric screw

threads — General plan
Filetages métriques ISO pour usages généraux — Vue d’ensemble

A Reference number
ISO 261:1998(E)
ISO 261:1998(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.

Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.

International Standard ISO 261 was prepared by Technical Committee ISO/TC 1, Screw threads, Subcommittee
SC 1, Basic data.

This second edition cancels and replaces the first edition (ISO 261:1973) which has been technically revised.

© ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [email protected]
Printed in Switzerland

ii
INTERNATIONAL STANDARD © ISO ISO 261:1998(E)

ISO general purpose metric screw threads — General plan

1 Scope
This International Standard specifies ISO general purpose metric screw threads (M) having basic profile according
to ISO 68-1. Basic dimensions are given in ISO 724. For tolerances see ISO 965-1.

2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain
registers of currently valid International Standards.

ISO 68-1:1998, ISO general purpose screw threads — Basic profile — Part 1: Metric screw threads.

ISO 262:1998, ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts.

ISO 724:1993, ISO general purpose metric screw threads — Basic dimensions.

ISO 965-1:1998, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data.

ISO 5408:1983, Cylindrical screw threads — Vocabulary.

3 Definitions
For the purposes of this International Standard, the definitions given in ISO 5408 apply.

4 Designation
A screw thread in conformity with this International Standard shall be designated according to ISO 965-1.

1
ISO 261:1998(E) © ISO

5 Choice of diameter and pitch

5.1 Choose, for preference, diameters in column 1 of table 2 and, if necessary, in column 2 and then in column 3.

Diameter 35 mm, and pitch 1,25 mm of diameter 14 mm shall be used only for the special cases indicated in the
footnotes.

Pitches shown in parentheses are to be avoided as far as possible.

5.2 The words "coarse" and "fine" are given in order to conform to usage. No concept of quality shall, however, be
associated with these words.

It shall be understood that the "coarse" pitches are the largest metric pitches used in current practice.

5.3 For the diameter (or the diameter range) selected, choose one of the pitches shown on the corresponding line
(or lines).

5.4 If screw threads finer than those appearing in table 2 are found necessary, only the following pitches shall be
used:

3 mm; 2 mm; 1,5 mm; 1 mm; 0,75 mm; 0,5 mm; 0,35 mm; 0,25 mm; 0,2 mm

When selecting such pitches, take into account the fact that there is increasing difficulty in complying with
tolerances as the diameter is increased for a given pitch. It is suggested, that diameters larger than those shown in
table 1 should generally not be used with the pitches indicated.

Table 1 — Maximum nominal diameter

Dimensions in millimetres

Pitch Maximum nominal diameter

0,5 22

0,75 33

1 80

1,5 150

2 200

3 300

2
© ISO ISO 261:1998(E)

Table 2 — Nominal diameter/pitch

Dimensions in millimetres

Nominal diameter D, d Pitch P

Col. 1 Col. 2 Col. 3 coarse fine

1st choice 2nd choice 3rd choice
3 2 1,5 1,25 1 0,75 0,5 0,35 0,25 0,2

1 0,25 0,2
1,1 0,25 0,2
1,2 0,25 0,2
1,4 0,3 0,2
1,6 0,35 0,2
1,8 0,35 0,2
2 0,4 0,25
2,2 0,45 0,25
2,5 0,45 0,35
3 0,5 0,35
3,5 0,6 0,35
4 0,7 0,5
4,5 0,75 0,5
5 0,8 0,5
5,5 0,5
6 1 0,75
7 1 0,75
8 1,25 1 0,75
9 1,25 1 0,75
10 1,5 1,25 1 0,75
11 1,5 1 0,75
12 1,75 1,5 1,25 1
14 2 1,5 1,25 a 1
15 1,5 1
16 2 1,5 1
17 1,5 1
18 2,5 2 1,5 1
20 2,5 2 1,5 1
22 2,5 2 1,5 1
24 3 2 1,5 1
25 2 1,5 1
26 1,5
27 3 2 1,5 1
28 2 1,5 1
30 3,5 (3) 2 1,5 1
32 2 1,5
33 3,5 (3) 2 1,5
35 b 1,5
36 4 3 2 1,5
38 1,5
39 4 3 2 1,5
(continued)

3
ISO 261:1998(E) © ISO

Table 2 (continued )
Dimensions in millimetres

Nominal diameter D, d Pitch P

Col. 1 Col. 2 Col. 3 coarse fine
1st choice 2nd choice 3rd choice 8 6 4 3 2 1,5
40 3 2 1,5
42
4,5 4 3 2 1,5
45 4,5 4 3 2 1,5
48 5 4 3 2 1,5
50 3 2 1,5
52 5 4 3 2 1,5
55 4 3 2 1,5
56 5,5 4 3 2 1,5
58 4 3 2 1,5
60 5,5 4 3 2 1,5
62 4 3 2 1,5
64 6 4 3 2 1,5
65 4 3 2 1,5
68 6 4 3 2 1,5
70 6 4 3 2 1,5
72 6 4 3 2 1,5
75 4 3 2 1,5
76 6 4 3 2 1,5
78 2
80 6 4 3 2 1,5
82 2
85 6 4 3 2
90 6 4 3 2
95 6 4 3 2
100 6 4 3 2
105 6 4 3 2
110 6 4 3 2
115 6 4 3 2
120 6 4 3 2
125 8 6 4 3 2
130 8 6 4 3 2
135 6 4 3 2
140 8 6 4 3 2
145 6 4 3 2
150 8 6 4 3 2
155 6 4 3
160 8 6 4 3
165 6 4 3
170 8 6 4 3
175 6 4 3
180 8 6 4 3
185 6 4 3
190 8 6 4 3
195 6 4 3
200 8 6 4 3
(continued)

4
© ISO ISO 261:1998(E)

Table 2 (concluded )
Dimensions in millimetres

Nominal diameter D, d Pitch P

Col. 1 Col. 2 Col. 3 coarse fine
1st choice 2nd choice 3rd choice 8 6 4 3 2 1,5
205 6 4 3
210 8 6 4 3
215 6 4 3
220 8 6 4 3
225 6 4 3
230 8 6 4 3
235 6 4 3
240 8 6 4 3
245 6 4 3
250 8 6 4 3
255 6 4
260 8 6 4
265 6 4
270 8 6 4
275 6 4
280 8 6 4
285 6 4
290 8 6 4
295 6 4
300 8 6 4
a Only for spark plugs for engines.
b Only for locking nuts for bearings.

5
ISO 261:1998(E) © ISO

ICS 21.040.10
Descriptors: screw threads, ISO metric threads, form specifications, dimensions, diameters, thread pitch, designation.

Price based on 5 pages