Scribd Logo
Upload

Welcome to Scribd!

  • 14 views

    Barriera Al Vapore

    Uploaded by

    Gavril Anca
    This document provides information about a low density polyethylene geomembrane produced by Plastika Kritis SA. It lists the product type, colour, thickness, carbon black content, density, and typical test values for tensile strength, elongation, puncture resistance, and tear resistance.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Barriera Al Vapore

    Uploaded by

    Gavril Anca
    14 views1 page
    This document provides information about a low density polyethylene geomembrane produced by Plastika Kritis SA. It lists the product type, colour, thickness, carbon black content, density, and typical test values for tensile strength, elongation, puncture resistance, and tear resistance.

    Original Description:

    barriera-al-vapore

    Original Title

    barriera-al-vapore

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides information about a low density polyethylene geomembrane produced by Plastika Kritis SA. It lists the product type, colour, thickness, carbon black content, density, and typical test values for tensile strength, elongation, puncture resistance, and tear resistance.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    14 views1 page

    Barriera Al Vapore

    Uploaded by

    Gavril Anca
    This document provides information about a low density polyethylene geomembrane produced by Plastika Kritis SA. It lists the product type, colour, thickness, carbon black content, density, and typical test values for tensile strength, elongation, puncture resistance, and tear resistance.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    KRITIFLEX® 6050 0.

    30mm

    PRODUCER PLASTIKA KRITIS SA

    TYPE Low Density Polyethylene (LDPE) geomembrane


    COLOUR BLACK

    NOMINAL THICKNESS (mm) 0.30


    AVERAGE THICKNESS (mm) 0.30 (± 5%)

    TESTED PROPERTIES UNIT TEST METHOD TYPICAL VALUES


    CARBON BLACK CONTENT % ASTM D4218 2-3
    CARBON BLACK DISPERSION note NFT 51142 ≤3
    3
    DENSITY OF MEMBRANE g/cm ASTM D792 0.935
    o
    MELT FLOW INDEX g/10min.190 C ΑSTM D1238 0.40

    2
    TENSILLE STRENGTH AT YIELD N/mm ASTM D638IV 9
    2
    TENSILLE STRENGTH AT BREAK N/mm ASTM D638IV 21
    ELONGATION AT YIELD % ASTM D638IV 17
    ELONGATION AT BREAK % ASTM D638IV 550
    PUNCTURE RESISTANCE N ASTM D4833 100
    TEAR RESISTANCE N ISO 34-1b 30

    The typical values refer to results obtained in our laboratory


    during Quality Control of various production batches

    P.O Box 1093, 711 10 Iraklion Crete Greece

    CERTIFIED QUALITY SYSTEM Tel:+30 2810 308500 Fax:+30 2810 381328


    ΕΛΟΤ ΕΝ ISO 9001:2000/ISO 9001:2000
    No. 02.14.02/051.01 Email: [email protected]

    LIMIT OF LIABILITY
    PLASTIKA KRITIS SA warrants that its products conform to PLASTIKA KRITIS’ specifications for these products.
    THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, STATUTORY
    OR OTHERWISE, INCLUDING BUT NOT LIMITED TO MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR
    PURPOSE. Buyer assumes all risks and responsibility for results or inquiry in use or handling of the products or
    their suitability for any particular end use. The amount of any claim against PLASTIKA KRITIS and PLASTIKA
    KRITIS’ liability shall in no event exceed the purchase price of the product. In no event shall PLASTIKA KRITIS SA
    be liable to Buyer for loss of profits or special, indirect or consequential damage.

    You might also like