Pressure Calibrators

Pressure Pumps & References

Manual Pressure Pumps

Mobile and simple

Pressure is one of the most commonly measured quanti- Requirements for pressure sources
ties in engineering, which is why exact and reliable pres-
The essential requirements for manual pressure genera-
sure measurement is especially important.
tion are:
However, the characteristics of the even best sensor or
transducer can be altered by a wide variety of factors. • Easy connection to test samples
This drift cannot be prevented, and it leads to incorrect • Simple and easy pressure generation
readings. • Maintenance free operation
Calibration allows these deviations to be measured and
These aspects have been taken into account and im-
documented in a certificate. All pressure measuring
plemented in the design of our test pumps and pressure
devices that significantly affect processes or activities
generators.
should be calibrated before being used.
Good reasons for proper and reliable calibration:
• Maintaining consistently high product quality
• Fulfilling industrial requirements
• Fulfilling quality assurance requirements
• Process optimisation
• Increasing productivity
• Avoiding unexpected production downtimes
• Employee and customer safety
• Environmental requirements/ecological aspects
• Profit optimisation/economic aspects
SIKA‘s mobile test and calibration devices are effective
aids for performing the necessary test and calibration
tasks quickly.

Digital pressure gauge

(Reference)

Easy pressure generation

Test pumps or pressure generators

SIKA portable pressure generators are the first choice
for stationary use. Unlike complicated and sensitive plate
Test sample scales, there is no need to take gravity into account or
perform complicated alignment, since measurements are
based on direct comparison. Another advantage of pres-
sure generators is one-hand operation, which makes re-
petitive test runs more ergonomic.
-2-
 A single pump for a variety of requirements
Hydraulic or pneumatic
Air, water and oil are used as pressure media. Especially
in application areas in which wetting of the test sample
is not allowed or the use of aggressive or ionising sub-
stances must be avoided, air is the ideal test medium. 
SIKA‘s pneumatic test pump fulfils requirements that in 
many cases can only be covered by several pumps from
other suppliers.
 Manual pressure generation in the medium pressure
range up to 60 bar using a handle is unique – no other
pump can do this.
 Integrated negative pressure capability enables oper-
ating with vacuum down to -950 mbar. A changeover
valve enables switching from positive pressure to nega-
tive pressure with no need for special tools.
 A large-volume pressure regulator with ultrafine thread 
pitch is used for precise pressure adjustment in the low
mbar range, enabling accurate settings in the low pres-
sure region.
The easily operated hydraulic test pumps and pressure
generators are specifically designed for the medium to
high pressure range.
They have a built-in reservoir for the hydraulic fluid. Pres-
sures up to 350 bar, 700 bar or 1000 bar can be gener-
ated, depending on the model.

OEM version and full version

A matching pressure hose is part of the basic configu-
ration of the OEM version of each test pump. The hy-
draulic hoses are fitted with a self-sealing quick coupling.
Inch, conical or metric adapters for all commonly used
connection threads are available in the full version. A
matching seal kit is also included with the pump. All of the
equipment is held in a carrying case with a foam-rubber
insert.

Adapter kits

Standard adapter kit

G⅛ G¼ G⅜ G½ ⅛ NPT ¼ NPT ½ NPT M12 x 1.5 M20 x 1.5 G ⅛A G ¼A

-3-
Pneumatic Pressure Pumps

Types P 40.2 and P 60

Pressure/vacuum change-over valve

Pressure hose
Pressure relief valve

Fine adjustment valve

Pump body

Handles / Push rod / Piston connection

Type P 40.2 P 60
OEM version

Pressure medium Air

Dimensions approx. 240 x 170 x 50 mm
Weight approx. 1.1 kg
Pressure ranges
Negative pressure -0.95 bar -0.95 bar
Positive pressure 40 bar 60 bar
Connections
Reference G¼
Test sample G ¼ with quick coupling and pressure hose (1 m)

Full version

Adapter kit Chrome-plated brass

Gasket kit Teflon® Seals and O-rings
Dimensions approx. 450 x 370 x 110 mm
Weight approx. 4.2 kg

-4-
Hydraulic Pressure Pumps

Types P 350.1, P 700.1L and P 1000.1

Pressure relief valve Fine adjustment valve

Pressure hose connection Reservoir

Handles / Push rod / Piston connection

Type P 350.1 P 700.1L P 1000.1 P 700.G

OEM version

Pressure medium Distilled water or hydraulic fluid Hydraulic fluid

Dimensions approx. 240 x 170 x 50 mm approx. 236 x 159 x 70 mm approx. 230 x 180 x 40 mm
Weight approx. 1.1 kg 1.8 kg 1.8 kg approx. 6.6 kg
Pressure ranges
Negative pressure 0...350 bar 0...400 bar 0...400 bar 
Positive pressure 0...350 bar 0...700 bar 0...1000 bar 0...700 bar
Connections
Reference G½ G⅜ G⅜ G½
Test sample G ¼ with quick coupling and pressure hose (1 m) G½

Full version

Adapter kit Chrome-plated brass Stainless steel

Gasket kit Teflon® Seals and O-rings
Dimensions approx. 450 x 370 x 110 mm
Weight approx. 3.5 kg approx. 3.5 kg approx. 3.5 kg approx. 9.3 kg

-5-
 Practical and independent
Practical Mobile and independent
The test pumps and pressure generators are designed to SIKA test pumps and pressure generators are ideal for
enable the direct connection of all pressure systems to be mobile use. Their low weight and compact design make
tested using adapters. The test sample is easily connect- them easy to transport directly to the measurement site.
ed using the rugged industrial hose with integrated quick The instruments can be used immediately and do not
coupling and supplied adapters. The reference is fitted require an additional power supply. There is no need to
directly at the top of the pump using a positioning adapter. take along nitrogen bottles or connect the equipment to
a compressed air network. Wear-free manual pressure
generation is simple and easy, regardless of ambient
temperature and orientation.
Fine adjustment
►

Reference connection

► ►
Test connection Discharge
►

► ►
Possible areas of application
Force applied by pressing the handles together SIKA test pumps and pressure generators can be used
everywhere, including on site in workshops, test and
measurement rooms as well as laboratories. They cover
The required test pressure is initially generated using the a broad spectrum of industries with diverse applications.
handles and then adjusted precisely with the fine adjust-
ment valve. As a result, the pressure on both instruments • Assembly and commissioning
is the same. • Manufacturing and production
The pressure relief valve allows continuous pressure re- • Maintenance and service
duction and ensures accurate and easy testing, even with • Quality assurance and test equipment monitoring
decreasing pressure.
• Repair
In the simplest case, the pressure is indicated by an
analogue pressure gauge. An easy to read digital pres- SIKA test pumps and pressure generators are suitable
sure gauge or hand-held instrument can also be used. The for testing, adjusting and calibrating pressure sensors,
accuracy or adjustment of the pressure measuring device pressure gauges, pressure switches, safety valves and
being tested can be checked by comparing the indicated all types of pressure devices. They are optimised in their
reference value with the measured value for the device function and use and assist in the performance of specific
under test. tests and inspections.
-6-
Digital Pressure Gauges

Exact and reliable

Digital pressure gauges are particularly suitable for both Negative / Positive and Differential pressure
stationary and mobile measurement and display of pres- Measuring ranges from -1 bar negative pressure to
sure. They can be used as reference pressure gauges to 2500 bar positive pressure with high overpressure pro-
simplify the checking, adjustment and calibration of other tection are available. Very small differential pressures
pressure measurement devices directly on site. in the millibar range can also be measured. Differential
High accuracy in signal acquisition is achieved by using pressure measuring cells or two independent measuring
high-performance measuring cells with electronic lineari- inputs are used for this purpose.
sation of the characteristic curve. Suitable instruments
are available for a wide variety of measurement tasks. Resolution / Accuracy
Ease of use is assured by innovative design and ad- It is often necessary to use several mechanical pres-
vanced technology. All essential functions for everyday sure gauges when measurements must be made
use can be selected conveniently at the press of a button. over a wide pressure range with sufficient accura-
Excellent protection against dust and moisture is provid- cy. Digital pressure gauges with high resolution and
ed by a membrane keypad or rubber buttons. precision can handle this task with just one
Integrated supplementary functions make our digital instrument.
pressure gauges true all-rounders. An indicating accuracy of 0.5% to 0.01% covers the entire
spectrum of requirements. This precision is often found
only in sensitive laboratory instruments, whereas SIKA
digital pressure gauges are designed for use in harsh in-
dustrial environments.

Tara / Zero
User-defined zero point setting at the push of a button
makes offset adjustment easy and eliminates the need
for tedious mechanical adjustment. Single-point adjust-
ment allows the linear characteristic curve to be shifted
in positive or negative direction over the entire measuring
range.

Linearisation
Multi-point adjustment can be performed if it is necessary
to adjust the indicated values at different test points. Two-
point adjustment is available for setting the zero point and
slope of the measuring cell curve. Some digital pressure
gauges allow up to six offset values to be programmed
in order to shift the characteristic curve to meet the most
stringent customer expectations.

Advantages at a glance Battery operation / Auto-Off

• Exact and reliable measurement Power is supplied by long-life batteries (ordinary or re-
chargeable). An external AC adapter can also be used. To
• High operational readiness increase battery operating time, a programmable Auto-
• Easy and clear readout Off function switches off the power to the instrument after
• Well suited to difficult on-site tasks prolonged inactivity. The electronics are designed for ex-
tremely low power consumption, which enables a battery
• Easy to assemble and use life of significantly more than 1000 hours.
• Supplementary functions for extra value

-7-
Digital pressure gauge selection table

Direct-mounting display instruments

BASIC SOLID PREMIUM

E2 D2 R P L
Performance     
Accuracy (FS) 0.5 % 0.1 % 0.1 % 0.5 % 0.05 %
0.1 % 0.025 %
0.05 % 0.01 %
Pressure range

-1...1 bar -1...1 bar

-1...2 bar
-1...2.5 bar -1...2.5 bar
-1...3 bar
-1...5 bar -1...5 bar

-1...10 bar -1...10 bar

-1...20 bar -1...20 bar -1...20 bar
-1...40 bar
0...50 bar 0...50 bar
-1...60 bar
0...100 bar 0...100 bar
0...200 bar
0...250 bar 0...250 bar
0...350 bar 0...350 bar
0...400 bar 0...400 bar
0...500 bar 0...500 bar
0...700 bar 0...700 bar 0...700 bar
0...1000 bar 0...1000 bar 0...1000 bar 0...1000 bar
0...1500 bar 0...1500 bar
0...2000 bar 0...2000 bar
0...2500 bar
Function     
Multi-point adjustment  
Interchangeable measuring cell
PC connection ○ ○ 
Data memory 
Analogue output ○
Second measuring input
Relais output ○
Built-in version ○
-8-
 Hand-held instruments

BASIC SOLID BASIC SOLID PREMIUM

MH3161 MH3181 MH3111 MH3151 MH3156

    

0.2 % 0.2 % 0.2 % 0.2 % 0.2 %

-2...2.5 mbar
-1...25 mbar -20...25 mbar
0...100 mbar
0...250 mbar
-10...350 mbar -200...350 mbar
0...400 mbar
0...1 bar
0...1.3 bar 0...1.3 bar
-1...1.5 bar
-100...2000 mbar -1...2 bar
0...2.5 bar
-1...3 bar
0...4 bar
0...6 bar
0...7 bar
-1...10 bar
0...16 bar
0...25 bar
0...40 bar
0...60 bar
0...100 bar
0...160 bar
0...250 bar
0...400 bar
0...600 bar

0...1000 bar

    


    
  
    
  
  


-9-
 Easy on-site use
Display Electronics / Pressure measuring cell
The large illuminated digital local display shows the The measuring cells and electronics used in the gaug-
measured pressure and indicates the current status of es are temperature compensated, so that the ef-
the digital pressure gauge, even under poor lighting con- fect of temperature on the readings is negligible. Liq-
ditions. This eliminates the difficult task of reading a dial uid entry into the measuring system is not necessary,
gauge and avoiding parallax errors. Needle jitter due to which eliminates the risk of damage from media resi-
vibration or pressure fluctuations is eliminated. Display dues. Another unbeatable feature of the electronic
damping or averaging can be configured directly using measuring cells is their immunity to pressure surges.
display filters. This ensures easy, tireless readout.
Min / Max displays and Peak function
Selectable pressure units Experience shows that excess pressure and pressure
Another feature is the large selection of pressure units. peaks significantly higher than normal operating pressure
Up to 13 different units are possible – far more than any occur at some measuring points. Min/max displays and fast
complicated dual-scale or multi-scale gauge can offer. peak value measurement cycles in digital pressure gaug-
The required display unit is selected directly on the es assist in system analysis and allow peak values to be
digital pressure gauge and is clearly indicated on the determined. This allows incorrect readings and violations
display. No conversion necessary; the desired value of range limits to be detected and helps avoid damage
can be read directly. to pressure systems. Preventive service is often less ex-
pensive than repairing or replacing defective instruments.

Protection class
High IP protection classes are available to minimise dust
and water sensitivity. Rugged, impact-resistant digital
pressure gauges are fitted with rubber caps for protection
during transport and field use.

Area of application
The right measuring system is available for every meas-
uring task. For simple applications with air or non-corro-
sive and non-ionising substances, low-cost unenclosed
pressure sensors are used. In difficult applications with
water or other aggressive media, high-quality stainless Direct mounting, built-in version and
steel versions are used. hand-held instrument
Once the intended use has been determined and the The compact, handy design proves its worth in everyday
pressure range has been specified, a digital pressure use. It puts an end to large-diameter gauges with sizes
gauge with an internal measuring cell is preferably used. up to 250 mm, as is common with precision pressure
For frequently changing application conditions, plug-in gauges. The small size simplifies direct mounting. If nec-
pressure sensors for various pressure ranges and appli- essary, built-in versions are available for switchgear cabi-
cations can be fitted using adapters. Automatic sensor net or control panel mounting. Hand-held digital pressure
recognition using standard DIN connectors offers a sim- gauges are especially suitable for applications where
ple Plug-&-Play solution. short-term pressure measurements are desired instead
of continuous measurement.

- 10 -
 Supplementary functions
PC connection and software Analogue output
Many digital pressure gauges have a serial interface An electrical output signal enables remote display on a
port to allow measurement values and stored data to control console or in a control room as well as the con-
be transferred directly to a PC and documented. An in- nection of external recorders and indicating instruments.
expensive measurement data acquisition system can
easily be assembled with suitable software and an in- Relay output / Alarm signalling
terface converter. Processes can be readily monitored Digital pressure gauges allow limit contacts to be closed
and analysed using the recorded and visualised meas- even at low pressures. There is no need for high actuation
urements and all data can be exported using standard forces for magnetic spring or inductive contacts, which
programs such as Microsoft Excel. Remote control is makes it easier to signal critical equipment conditions and
also possible. Various software packages with exten- perform supplementary control tasks. A built-in buzzer gen-
sive recording and display functions, logger and alarm erates an alarm when the pressure exceeds the range of
evaluation as well as for calibration are available. the programmed minimum and maximum pressure levels.

Temperature display
Temperature measurement is often required in addition
to pressure measurement. For this purpose, a tempera-
ture sensor is integrated in the measuring cell to detect
the temperature of the medium. The process temperature
can be displayed at the press of a button. This allows two
quantities to be measured at a single measuring point,
which saves costs.

Explosion protection
Explosion-proof versions are also available for use in po-
tentially explosive locations, e.g. oil refineries, chemical
plants and drilling platforms.

Example applications
Data memory • Continuous or temporary checking of a wide variety of
The logger function for local data storage can be used system pressures
to record pressure curves automatically and perform • Air density measurement in building shells for the de-
leak tests. The integrated data memory in digital pres- tection and elimination of problem areas and avoiding
sure gauges allows a variety of data sets to be recorded structural damage
directly. The time interval between samples is program-
mable and the maximum recording interval is configur- • Monitoring the degree of soiling of filter units in venti-
able. The stored values can be displayed on a PC. Data lation or air conditioning systems
import at the press of a button is also possible. In this • Recording pressure drops for the determination of
case the data is shown directly on the display. In this leakage rates in leak tests
process the values are automatically annotated with the • Measurement of barometric air pressure for the deter-
date and time of day using an integrated real-time clock. mination of weather conditions
• Reference pressure gauge for calibration tasks

- 11 -
Types E2, D2 and R

type E2 / D2 type R

Technical data Technical data

Accuracy (FS) E2 0.5 % D2 0.1 % Accuracy (FS) 0.1 %
Pressure ranges Resolution Pressure ranges Resolution
-1...3 bar 1 mbar -1...1 bar 1 mbar
-1...40 bar 10 mbar -1...2.5 bar 1 mbar
-1...60 bar 10 mbar -1...5 bar 1 mbar
0...400 bar 100 mbar -1...10 bar 10 mbar
0...700 bar 100 mbar -1...20 bar 10 mbar
0...1000 bar 100 mbar 0...50 bar 10 mbar
0...100 bar 100 mbar
0...250 bar 100 mbar
0...350 bar 100 mbar
0...500 bar 100 mbar
0...700 bar 100 mbar
0...1000 bar 1 bar
0...1500 bar 1 bar
0...2000 bar 1 bar

- 12 -
Functions
Type E2 / D2 R
Adjustment options
Linearisation - 6 points
Tare/Zero  
Selectable units
Pressure bar, mbar, kPa, MPa, PSI bar
Temperature - °C
Features
Measuring inputs 1 x direct 1 x direct
PC connection RS232 (optional)
Analogue output
Relay output
Alarm buzzer
Built-in version
Explosion protection
Data memory
Number of memories 60.000 values (auto)
Recording interval 1 sec...10 h
Recording duration 1 min...1000 h
Real-time clock/date
Store function
Data sets Pressure / Temperature
Display / Representation
Multi-functional LCD 4 ½ digit 4 digit
Bar graph 
Illumination 
Display filter  
Min/max value  
Average
Differential pressure
Measuring rate
Standard 10 ms 100 ms
Peak / Fast 10 ms 8 ms
Process connection
Connection options G¼ G½
Material 1.4404 1.4542
Medium temperature -20...80 °C -10...70 °C
for aggressive media  
Housing
Protection class IP67 (front) / IP67 IP65 (front) / IP40
Dimension Ø 80 mm T=30 mm H=100 mm Ø 85 mm T=30 mm H=30 mm
Material Zinc casting Aluminium
Operating temperature 0...50 °C -10...70 °C
Weight 540 g 450 g
Power
Auto-off function  
Battery type 2x 1.5 V AA 2x 1.5 V AAA
Ext. power
Battery operation 1500 h 8000 h

- 13 -
Typ P und L

type P type P built-in version type L

Technical data Technical data

Accuracy (FS) 0.5 % 0.1 % 0.05 % Accuracy (FS) 0.05 % 0.025 % 0.01 %
Pressure ranges Resolution Pressure ranges Resolution
-1...1 bar 1 mbar 1 mbar 0.1 mbar -1...2 bar 1 mbar
-1...2.5 bar 1 mbar 1 mbar 0.5 mbar -1...20 bar 1 mbar
-1...5 bar 1 mbar 1 mbar 0.5 mbar 0...200 bar 10 mbar
-1...10 bar 10 mbar 10 mbar 1 mbar 0...400 bar 50 mbar
-1...20 bar 10 mbar 10 mbar 2 mbar 0...1000 bar 100 mbar
0...50 bar 10 mbar 10 mbar 5 mbar
0...100 bar 100 mbar 100 mbar 10 mbar
0...250 bar 100 mbar 100 mbar 20 mbar
0...350 bar 100 mbar 100 mbar 50 mbar
0...500 bar 100 mbar 100 mbar 50 mbar
0...700 bar 100 mbar 100 mbar 50 mbar
0...1000 bar 1 bar 1 bar 100 mbar
0...1500 bar 1 bar 1 bar 200 mbar
0...2000 bar 1 bar 1 bar 500 mbar
0...2500 bar 1 bar 1 bar

- 14 -
Functions
Type P L
Adjustment options
Linearisation 6 points
Tare/Zero  
Selectable units
Pressure bar, mbar, kPa, MPa, PSI bar, mbar, hPa, kPa, MPa, PSI, mmHg, inHg,
Temperature - cmH2O, mH2O, inH2O, ftH2O, Kp/cm²
Features
Measuring inputs 1 x direct 1 x direct
PC connection RS232 (optional) RS485
Analogue output 0(4)...20mA / 0...10 V (optional)
Relay output 2 x 24 VDC/1A (optional)
Alarm buzzer
Built-in version 
Explosion protection Ex II 2G Ex ia II C T6
Data memory
Number of memories
Recording interval
Recording duration
Real-time clock/date
Store function
Data sets
Display / Representation
Multi-functional LCD 4 digit (0.5 % / 0.1 %), 5 digit (0.05 %) 5 digit
Bar graph 
Illumination
Display filter 
Min/max value  
Average
Differential pressure
Measuring rate
Standard 100 ms 500 ms
Peak / Fast
Process connection
Connection options G½ G¼
Material 1.4542 1.4435
Medium temperature 0...50 °C 0...50 °C
for aggressive media  
Housing
Protection class IP65 (front) / IP40 IP65 (front) / IP54
Dimension 80 x 80 mm T=50 mm H=130 mm Ø 80 mm T=40 mm H=120 mm
Material Aluminium ABS plastic
Operating temperature 0...50 °C 0...50 °C
Weight 900 g 210 g
Power
Auto-off function  
Battery type 2x 1.5 V AAA 1x 3 VCR
Ext. power 24 VDC
Battery operation 8000 h 2000 h

- 15 -
Type MH 3161 and MH 3181

type MH 3161 / MH 3181

Technical data
Accuracy (FS) 0.2 %
Pressure ranges Resolution
-1...25 mbar 0.01 mbar
-10...350 mbar 0.1 mbar
0...1,3 bar (abs.) 1 mbar
-100...2000 mbar 1 mbar

- 16 -
Functions
Type MH 3161 MH 3181
Adjustment options
Linearisation 2 points
Tare/Zero 
Selectable units
Pressure bar, mbar, kPa, MPa, Pa, PSI, mmHg, mH2O
Temperature -
Features
Measuring inputs 2 x direct 2 x direct
PC connection TTL (USB optional) TTL (USB optional)
Analogue output 0...1 V
Relay output
Alarm buzzer 
Built-in version
Explosion protection Ex II 2G Ex ib II C T4 Ex II 2G Ex ib II C T4
Data memory
Number of memories 10.000 values (auto)
Recording interval 1...3600 sec.
Recording duration
Real-time clock/date 
Store function 99 Werte (manuell)
Data sets Pressure / min / max
Display / Representation
Multi-functional LCD 4½ digit 4½ digit
Bar graph
Illumination
Display filter 
Min/max value  
Average 
Differential pressure  
Measuring rate
Standard 250 ms 250 ms
Peak/Fast 1 ms
Process connection
Connection options Metal connection plugs Ø 6 mm
Material 2.0380 Nickel-plated
Medium temperature -10...50 °C
for aggressive media
Housing
Protection class IP65 (front) / IP40
Dimension 140 x 70 x 30 mm
Material ABS plastic
Operating temperature 0...50 °C
Weight 200 g
Power
Auto-off function 
Battery type 1x 9 V Block
Ext. power 12 VDC
Battery operation 350 h

- 17 -
 Type MH 3111, MH 3151 and MH 3156 with external pressure sensor

type MH 3111 / MH 3151 / MH 3156

+
See page 20 for pressure ranges of external pressure sensors.
- 18 -
Functions
Type MH 3111 MH 3151 MH 3156
Adjustment options
Linearisation 2 points
Tare / Zero 
Selectable units
Pressure bar, mbar, kPa, MPa, Pa, PSI, mmHg, mH2O
Temperature -
Features
Measuring inputs 1 x interchangeable 1 x interchangeable 2 x interchangeable
PC connection TTL (USB optional) TTL (USB optional) TTL (USB optional)
Analogue output 0...1 V 0...1 V
Relay output
Alarm buzzer  
Built-in version
Explosion protection Ex II 2G Ex ib II C T4 Ex II 2G Ex ib II C T4 Ex II 2G Ex ib II C T4
Data memory
Number of memories 10.000 values (auto) 4000 values (auto)
Recording interval 1...3600 sec. 1...3600 sec.
Recording duration
Real-time clock/date  
Store function 99 values (manual) 99 values (manual)
Data sets Pressure / min / max Pressure 1 & 2 / Min 1 & 2 / Max 1 & 2
Display / Representation
Multi-functional LCD 4½ digit 4½ digit 4½ digit
Bar graph
Illumination
Display filter  
Min/max value   
Average  
Differential pressure optional optional optional
Measuring rate
Standard 250 ms 250 ms 250 ms
Peak / Fast 1 ms 1 ms
Process connection (depending on chosen external pressure sensors)
Connection options Metal connection plugs Ø 6 G½
Material Nylon 1.4542
Medium temperature 0...50 °C 0...70 °C
for aggressive media 
Housing
Protection class IP65 (front) / IP40
Dimension 140 x 70 x 30 mm
Material ABS plastic
Operating temperature 0...50 °C
Weight 200 g
Power
Auto-off function 
Battery type 1x 9 V Block
Ext. power 12 VDC
Battery operation 350 h

- 19 -
External Pressure Sensors

Nylon- and stainless steel type

Type (Nylon)
Accuracy (FS) 0.2 %
Pressure ranges Resolution
MSD 2,5 MR -2...2.5 mbar (rel.) 0.001 mbar
MSD 25 MR -20...25 mbar (rel.) 0.01 mbar
MSD 350 MR -200...350 mbar (rel.) 0.1 mbar
MSD 1,3 BA 0...1.3 bar (abs.) 1 mbar
MSD 2 BA 0...2 bar (abs.) 1 mbar
MSD 2 BR -1...2 bar (rel.) 1 mbar
MSD 7 BA 0...7 bar (abs.) 10 mbar
MSD 10 BR -1...10 bar (rel.) 10 mbar
Type (stainless steel)
Nylon version
MSD 100 MRE 0...100 mbar (rel.) 0.1 mbar
Piezoresistive pressure sensor for air and non-corrosive/
non-ionising gases and liquids MSD 250 MRE 0...250 mbar (rel.) 0.1 mbar
MSD 400 MRE 0...400 mbar (rel.) 0.1 mbar
Two nylon nipples for 6 x 1 mm pressure tubing
MSD 1 BAE 0...1 bar (abs.) 1 mbar
Electronics Integrated amplifier and sensor data MSD 1 BRE 0...1 bar (rel.) 1 mbar
memory MSD -1/1,5 BRE -1...1.5 bar (rel.) 1 mbar
Electrical PVC cable (1 m)
MSD -1/3 BRE -1...3 bar (rel.) 1 mbar
connection with miniature DIN connector
MSD 2,5 BAE 0...2.5 bar (abs.) 1 mbar
Housing Impact-resistant ABS plastic
Water penetration rating IP65 MSD 2,5 BRE 0...2.5 bar (rel.) 1 mbar
Dimensions 70 x 30 x 15 mm (H x W x D) MSD 4 BAE 0...4 bar (abs.) 1 mbar
Weight approx. 75 g MSD 4 BRE 0...4 bar (rel.) 1 mbar
Stainless steel version MSD 6 BAE 0...6 bar (abs.) 1 mbar
Piezoresistive pressure sensor with separate connecting MSD 6 BRE 0...6 bar (rel.) 1 mbar
cable, for aggressive media as well as water, gases and liquids MSD 10 BAE 0...10 bar (abs.) 10 mbar
Stainless steel connection G ½ male thread MSD 10 BRE 0...10 bar (rel.) 10 mbar
MSD 16 BAE 0...16 bar (abs.) 10 mbar
Electronics Integrated amplifier and
sensor data memory MSD 25 BAE 0...25 bar (abs.) 10 mbar
Electrical PVC cable (1 m) MSD 25 BRE 0...25 bar (rel.) 10 mbar
connection with miniature DIN connector MSD 40 BRE 0...40 bar (rel.) 10 mbar
(optional)
MSD 60 BRE 0...60 bar (rel.) 10 mbar
Housing Stainless steel
Water penetration rating IP65 MSD 100 BRE 0...100 bar (rel.) 100 mbar
Dimensions approx. 30 x 90 mm (D x L) MSD 160 BRE 0...160 bar (rel.) 100 mbar
Weight approx. 220 g MSD 250 BRE 0...250 bar (rel.) 100 mbar
MSD 400 BRE 0...400 bar (rel.) 100 mbar
Nylon and stainless steel options
MSD 600 BRE 0...600 bar (rel.) 100 mbar
• Higher sensor accuracy (from 350 mbar)
MSD 1000 BRE 0...1000 bar (rel.) 1 bar
• Ex II 2G Ex ib IIC T4
- 20 -
Pressure Calibrators

Comparison of digital and analogue pressure gauges Manual test pumps or pressure generators are used for
Pressure calibration is the comparison between the in- simple pressure generation.
dicated values of a pressure measuring device with the SIKA offers a complete range of pressure calibrators for
indicated values of a pressure standard with a known ac- a wide variety of applications to allow specified test and
curacy. calibration tasks to be performed.
In many cases, the device to be tested cannot be re- Routine on-site calibrations can be performed very quick-
moved from the active process. ly and economically with the right combination of pres-
Calibration is performed on site to avoid lengthy down- sure generator and reference. This ensures that the indi-
times. Portable SIKA pressure calibrators are especially cated pressure values are correct and reliable and that all
suitable for this purpose. specified requirements are fulfilled.
In order to perform a specified functional test or accuracy
check, the test sample is often connected to the calibra-
tion device with a pressure hose. Digital pressure gauges
with sufficient precision can be used as compact refer-
ence instruments.

- 21 -
 Possible combinations

►
▼ Reference A Reference E2 Reference D2 Reference R Reference P Reference L

P 40.2 PM 40.2 A PM 40.2 E2 PM 40.2 D2 PM 40.2 R PM 40.2 P PM 40.2 L

P 60 PM 60 A PM 60 E2 PM 60 D2 PM 60 R PM 60 P 

P 350.1 PM 350.1 A PM 350.1 E2 PM 350.1 D2 PM 350.1 R PM 350.1 P PM 350.1 L

P 700.1L PM 700.1L A PM 700.1L E2 PM 700.1L D2 PM 700.1L R PM 700.1L P PM 700.1L L

P 1000.1  PM 1000.1 E2 PM 1000.1 D2 PM 1000.1 R PM 1000.1 P PM 1000.1 L

All manual pressure pumps and references can be combined as indicated above for various measuring ranges, resolutions and accuracy classes.

- 22 -
Calibrator PC 700+

Technical data
Accuracy (FS) 0.025 %
Pressure ranges (Resolution) 0...60 bar (5 mbar)
0...200 bar (20 mbar)
0...350 bar (30 mbar)
0...700 bar (70 mbar)
Function
Adjustment options
Tara / Zero 
Selectable units (Pressure) bar, PSI, kPa, MPa, atm, at (kgf/cm²), mmHg, mHg, inHg, cmH2O, mH2O, inH2O, torr
Features
Measuring inputs 1 x direct
PC connection RS232
Explosion protection EEx ia IIC T4
electronic measuring inputs 0...30 mA / 0...15 V
Data memory
Store function 30 x 10 values (manual)
Display/representation
Multi-functional LCD 5 digit
Illumination 
Display filter 
Min / max value 
Measuring rate
Standard 100 ms
Process connection
Connection options G¼
Material 2.4602
Medium temperature -20...80 °C
for aggressive media 
Housing
Protection class IP65 (front) / IP40
Dimension, weight 350 x 160 x 180 mm, 8.1 kg
Material Aluminium
Operating temperature 0...50 °C
Power
Auto-off function 
Battery type, battery operation 1x 9 V Block, 35 h
Ext. power 12 VDC

- 23 -
Our Production and Sales Range
®

Flow Sensors without moving Parts Turbine Flow Sensors Flow Switches

Pressure Gauges and Pressure Sensors Industrial Thermometers Electronic Digital Thermometers, Dial Thermometers

Measuring Instruments Temperature Sensors Calibrators, DKD-Laboratory

Your competent partner

for measurement and control

...measurement...control ...calibration
Phone: 0700 CALL SIKA
Phone: +49 5605 803-0
Fax: +49 5605 803-54
E-Mail: [email protected]
Internet: http://www.sika.net
Struthweg 7-9, 34260 Kaufungen
P. O. Box 11 13, 34254 Kaufungen
Germany
Druckkalibratoren_e 06/2012