Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.

(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any
other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any
other company which may arise as a result of the use of technical information described in this book.

(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
– Any applications other than the standard applications intended.

(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.

(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.

(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.

(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company.

20080805

If you have any inquiries or questions about this book or our semiconductor products, please contact one
of our sales offices listed on the back or our sales division.
2009 Ver.2 Microcomputer AM Series

Part Number List .....................5

AM1 (MN101) Series .............11

AM2 (MN102) Series ...........141

AM3 (MN103) Series ...........155

Package Outlines ................201

Development Support Tools ......205

 How to Read This Manual

 Performing Searches
This manual offers three methods to find the information you need quickly.
1) To search for the start of a series, refer to the index at the beginning of the volume.
2) To look for a particular listed product, refer to the chart of listed products at the beginning of the volume.
3) The names of the listed products are located at the top right corner of every page. This makes it possible to leaf through the pages
and stop at the place where the desired product name appears.

 Format of this Manual

This manual is divided by lists, specifications for the various series, package outlines, and development tools.
The page layout for the series specifications is composed of the product name, package, minimum instruction execution time, pin assignment,
etc. Shown below is a sample of page layout.

Electrical
characteristics Product name

Package
MN101C425, MN101C427

MN101C42 Series
 Electrical Charactreistics (Supply current)
Type MN101C425 MN101C427 MN101CP427 Limit
Parameter Symbol Condition Unit
Internal ROM type Mask ROM EPROM min typ max

Minimum ROM (byte)

RAM (byte)
8K
0.25K
16K
0.5K
Operating supply current IDD1
IDD2
fosc = 20 MHz , VDD = 5 V
fosc = 8.39 MHz , VDD = 5 V
15
6
40
18
mA
mA

instruction
Operating supply current
Package (Lead-free) QFP044-P-1010F, SDIP042-P-0600C, TQFP048-P-0707B IDD3 fx = 32.768 kHz , VDD = 3 V 100 µA
0.10 µs (at 4.5 V to 5.5 V, 20 MHz) IDD4 fx = 32.768 kHz , VDD = 3 V , Ta = 25°C 8 µA
Supply current at HALT

execution time
0.238 µs (at 2.7 V to 5.5 V, 8.39 MHz)
Minimum Instruction IDD5 fx = 32.768 kHz , VDD = 3 V , Ta = –40°C to +85°C 18 µA
0.477 µs (at 2.0 V to 5.5 V, 4.19 MHz)*
Execution Time VDD = 5 V , Ta = 25°C 2 µA
125 µs (at 2.0 V to 5.5 V, 32.768 kHz)*
Supply current at STOP IDD6
* The lower limit for operation guarantee for EPROM built-in type is 2.7 V. VDD = 5 V , Ta = –40°C to +85°C 20 µA

 Interrupts  Pin Assignment

RESET, Watchdog, External 0 to 2, External 3 (only 48-pin package), Timer 2 to 5, Time base, Serial 0, A/D conversion finish
P21, IRQ1, SENS
P14, TMIO4
P13, TMIO3
P12, TMIO2

P14, TMIO4
P13, TMIO3
P12, TMIO2
P22, IRQ2
P21, IRQ1
P20, IRQ0

P23, IRQ3
P22, IRQ2

P20, IRQ0

 Timer Counter
P63
P6 2
P6 1
P6 0

P11

Interrupts
P6 3
P6 2
P61
P60

P11

Timer counter 2 : 8-bit × 1 (square-wave/8-bit PWM output, event count, synchronous output event) TXD, SBO0, P00 1 42 VSS
RXD, SBI0, P01 2 41 OSC1
Clock source................ 1/1, 1/4 of system clock frequency; 1/1 of XI oscillation clock frequency (only 48-pin package); external SBT0, P02 3 40 OSC2
33
32
31
30
29
28
27
26
25
24
23

36
35
34
33
32
31
30
29
28
27
26
25

BUZZER, P06 4 39 VDD P64 34 22 P10, RMOUT

P64 37 24 P10, RMOUT
clock input RMOUT, P10
P11
5
6
38
37
PA7, AN7
PA6, AN6
P65 35 21 P06, BUZZER P65 38 23 P06, BUZZER
P66 36 20 P02, SBT0 P66 39 22 P02, SBT0
Interrupt source ........... coincidence with compare register 2 TMIO2, P12
TMIO3, P13
7
8
36
35
PA5, AN5
PA4, AN4 P67 37 19 P01, SBI0, RXD P67 40 21 P01, SBI0, RXD
TMIO4, P14 9 34 PA3, AN3 P70 41 20 P00, SBO0, TXD
IRQ0, P20 10 33 PA2, AN2
P70 38
MN101C425 18 P00, SBO0, TXD
MN101C425
Timer counter 3 : 8-bit × 1 IRQ1, P21
IRQ2, P22
11 32 PA1, AN1
PA0, AN0
NRST, P27 39
MN101C427
17 N.C. P71
NRST, P27
42
43 MN101C427
19
18
XO
XI
12 31 MMOD 40 16 VSS
(square-wave output, event count, generation of remote control carrier, serial 0 baud rate timer) P60
P61
13
14
30
29
P80, LED0
P81, LED1 LED7, P87 41 15 OSC1
MMOD
LED7, P87
44
45
17
16
VSS
OSC1
LED6, P86 42 14 OSC2
Clock source................ 1/4, 1/16 of system clock frequency; 1/1 of OSC oscillation clock frequency; external clock input P62
P63
15
16
28
27
P82, LED2
P83, LED3 LED5, P85 43 13 VDD
LED6, P86 46 15 OSC2
P64 P84, LED4 LED5, P85 47 14 VDD
17 26
Interrupt source ........... coincidence with compare register 3 P65 18 25 P85, LED5 LED4, P84 44 12 PA7, AN7 LED4, P84 48 13 PA7, AN7
10

12
11
10
11

P66 P86, LED6

1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9

19 24
P67 20 23 P87, LED7
Timer counter 2, 3 can be cascade-connected. NRST, P27 21 22 MMOD
LED3, P83
LED2, P82
LED1, P81
LED0, P80
N.C.
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6
LED3, P83
LED2, P82
LED1, P81
LED0, P80
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6

Pin assignment
MN101C425
Timer counter 4 : 16-bit × 1 (square-wave/16-bit PWM output, event count, synchronous output event, input capture) MN101C427
Clock source................ 1/4, 1/16 of system clock frequency; 1/1 of OSC oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register 4
SDIP042-P-0600C QFP044-P-1010F TQFP048-P-0707B
Time base timer (one-minute count setting, independently operable 8-bit timer counter 5)
Clock source................ 1/4 of system clock frequency; 1/1, 1/8192 of OSC oscillation clock frequency; 1/1, 1/8192 of XI
oscillation clock frequency (only 48-pin package)
Interrupt source ........... coincidence with compare register 5; 1/8192 prescaler overflow
Watchdog timer
Interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency (ROM option)

 Serial interface
Serial 0 : synchronous type/simple UART (half-duplex) × 1
Clock source................ 1/2, 1/4, 1/16 of system clock frequency; output of timer counter 3

I/O pins  I/O Pins

I/O 27: Common use: 16. Specified pull-up resistor available
Input/output selectable (bit unit): 26 (for 44-pin). 25 (for 42-pin)
Input 12: Common use, Specified pull-up resistor available

 A/D converter
10-bit × 8-ch. (with S/H)

 Special Ports
Buzzer output, remote control carrier signal output, high-current drive port

18 MAD00002FEM MAD00002FEM 19

2 How to Read This Manual

 Description
• Internal ROM type
Internal ROM type may be either "Mask ROM", "EPROM built-in type (EPROM)", "Flash memory built-in type (FLASH)", or
"External".

• Package
All packages are lead (Pb) free.
Development status may be either "in production" (no indication), "ES (Engineering Sample) available", "Under Development",
or "Under Planning".
For information on the supported packages, be sure to contact our business reception.

• Minimum instruction execution time

If it is possible to select the microcontroller operation clock (OSC or X), execution times are given separately for the main clock
and the sub clock.
When two types of minimum instruction execution time are given with no special description, the values are given as variations in
the operating voltage range or oscillation frequency.

• Interrupts
Interrupts are listed by source.
When jointly used, values are separated by a slash (" / ").
The number of sources indicated in the list is the total number except RESET.

• I/O pins
The number stated is the number of ports available for general use.
The detailed description provides an explanation of each pin. "P" is an abbreviation for "port".

• Electrical characteristics
The values listed under electrical characteristics are all reference values.

 Note!
For information regarding chip development status, package, EPROM built-in type, and availability of flash memory built-in type, please
consult our sales staffs (contact points are listed at the end of this manual).

 Note on Naming
If the additional digits for customer ROM version, etc. should produce a device name exceeding 12 characters, we reduce it to 12 characters
with the following schema.
The final device name appears, however, on delivery specifications and similar documents.

Description Full device name (13 or more characters) Abbreviated name (12 characters)
8-bit microcomputer MN101 – – – – – – – – MNB – – – – – – –
16-bit microcomputer MN102 – – – – – – – – MNP – – – – – – –
32-bit microcomputer MN103 – – – – – – – – MNZ – – – – – – –

If a device name still exceeds 12 digits regardless of the use of the abbreviated name, the name shall be
determined according to a separate standard.

How to Read This Manual 3

4 How to Read This Manual
Part Number List

Part Number List

 AM1(MN101) 8-bit Single-chip Microcontroller Series
Serial Interfaces

Display Control Function

Execution Time (µs) /
Operationg Voltage (V)

[At single chip mode]

Minimum Instruction

Number of I/O Ports

Internal ROM Type

A/D Converter (ch)

D/A Converter (ch)

Synchronous Type / UART

Synchronous Type / I²C

Synchronous Type
Interrupt Sources

16-bit Timer

19-bit Timer
ROM (byte)

RAM (byte)

8-bit Timer
Category

Package
Part No.

UART

Page
I²C
MN101C28A 32K 1.5K LQFP080-P-1414A
MN101C28C 48K QFP084-P-1818E
2K 0.1/4.5 - 5.5 TQFP080-P-1212D
MN101C28D M 64K 125/2.0 - 5.5
MN101C28F 4K
96K LQFP080-P-1414A 70 18 5 1 0 1 1 1 0 0 8   12
MN101C28L 10K
LQFP080-P-1414A
MN101CP28D 64K 2K 0.1/4.5 - 5.5 QFP084-P-1818E
E 125/2.3 - 5.5 TQFP080-P-1212D
MN101CP28L 96K 10K LQFP080-P-1414A
MN101C309 24K 1K 0.1/4.5 - 5.5
M 125/2.0 - 5.5
MN101C30A LQFP064-P-1414 54 17 5 1 0 1 0 1 0 0 8   14
32K 1.5K 0.1/4.5 - 5.5
MN101CP30A E 125/2.7 - 5.5
0.1/4.5 - 5.5 QFP044-P-1010F 37
0.477/2.0 - 5.5 11
MN101C425 8K 0.25K SDIP042-P-0600C 36
0.1/4.5 - 5.5
125/2.0 - 5.5 TQFP048-P-0707B 39 12
M
0.1/4.5 - 5.5 QFP044-P-1010F 37
0.477/2.0 - 5.5 11
MN101C427 SDIP042-P-0600C 36 3 1 0 1 0 0 0 0 8   16
0.1/4.5 - 5.5
125/2.0 - 5.5 TQFP048-P-0707B 39 12
16K 0.5K
QFP044-P-1010F 37
0.1/4.5 - 5.5 11
MN101CP427 E 0.238/2.7 - 5.5 SDIP042-P-0600C 36
TQFP048-P-0707B 39 12
MN101C457 M 0.1/4.5 - 5.5
16K 0.5K 0.1/4.5 - 5.5 QFP044-P-1010F 37 11 3 1 0 1 0 0 0 0 8   18
MN101CP427 E 0.238/2.7 - 5.5
0.1/4.5 - 5.5
MN101C539 M 62.5/2.0 - 5.5
24K 0.5K 0.1/4.5 - 5.5
TQFP048-P-0707B 40 14 3 1 0 1 0 0 0 0 8   20
MN101CP539 E 62.5/2.7 - 5.5
MN101C61D 64K 3K 0.1/2.5 - 3.6
M 0.2/2.1 - 3.6
MN101C61G 125/1.8 - 3.6
0.1/2.5 - 3.0
MN101CF60G 0.2/2.2 - 3.0 TQFP080-P-1212D 68 25 7 1 0 1 1 1 0 0 6   22
128K 12K 125/2.2 - 3.0
F 0.1/2.7 - 3.6
MN101CF61G 0.2/2.7 - 3.6
125/2.7 - 3.6
ADC Built-in
Type MN101C62D 64K 2K 0.1/4.5 - 5.5
M 0.25/2.7 - 5.5
MN101C62F 96K 4K 62.5/2.0 - 5.5
0.1/4.5 - 5.5
LQFP080-P-1414A 68 25 6 2 0 2 1 0 0 0 8   24
MN101CF62G F 128K 10K 0.25/2.7 - 5.5
62.5/2.5 - 5.5
MN101C67D 64K 6K 0.1/2.5 - 3.6
M 0.2/2.1 - 3.6
MN101C67G 62.5/1.8 - 3.6 TQFP080-P-1212D 69 26 6 1 0 2 1 1 0 1 7   26
128K 10K
MN101CF67G F 0.1/2.7 - 3.6
0.1/2.7 - 3.6
MN101CF91D F 64K 4K 62.5/2.7 - 3.6 TQFP048-P-0707B 37 26 6 2 0 2 1 0 0 0 6   28
0.1/4.5 - 5.5
MN101C94A M 32K 1K 0.238/2.7 - 5.5
0.477/2.0 - 5.5
0.1/4.5 - 5.5
QFP044-P-1010F 37 13 5 1 0 1 0 0 0 0 8   30
MN101CF94D F 64K 2K 0.238/2.7 - 5.5
0.477/2.5 - 5.5
0.1/2.7 - 3.6
MN101CF95G F 128K 6K 62.5/2.7 - 3.6 TQFP080-P-1212D 67 30 7 2 0 3 2 0 0 0 11   32
MN101C97A 32K
M 0.5/1.8 - 3.6 QFP044-P-1010F  38 20
MN101C97D 1K 5 1 0 1 1 0 0 0 8   34
64K 62.5/1.8 - 3.6 TQFP048-P-0707B
MN101CF97D F
MN101CA7A M 32K 0.1/2.7 - 3.6 TQFP048-P-0707B
2K 62.5/1.8 - 3.6 35 22 5 1 0 1 1 0 0 1 8   36
MN101CFA7D F 64K TQFP048-P-0707B 
MN101CB6A 32K 1K
MN101CB6D M 64K 0.1/2.7 - 3.6 SSOP032-P-0300B
0.125/1.8 - 3.6 17 15 5 1 0 1 0 0 0 0 5   38
MN101CB6G 124K 2K 100/1.8 - 3.6
MN101CFB6G F 128K SSOP032-P-0300B 
MN101CD0A 32K 1K
MN101CD0D M 64K 0.1/2.7 - 3.6 SSOP032-P-0300B
0.125/1.8 - 3.6 23 18 5 1 0 1 0 0 0 0 5   40
MN101CD0G 124K 2K 100/1.8 - 3.6
MN101CFD0G F 128K SSOP032-P-0300B 
MN101E16K 256K 12K LQFP100-P-1414
M QFP100-P-1818B
MN101E16Y 384K 20K 0.059/2.7 - 3.6 QFP100-P-1818B
30.6/2.7 - 3.6 85 27 9 1 0 3 2 0 0 0 8   42
LQFP100-P-1414
MN101EF16K 260K 16K
F QFP100-P-1818B
MN101EF16Z 512K 30K QFP100-P-1818B
0.042/2.2 - 5.5
MN101EF34D F 64K+4K 4K 62.5/2.2 - 5.5 TQFP048-P-0707B 39 28 6 3 0 2 1 0 0 0 8   44

6
 Serial Interfaces

Display Control Function

Execution Time (µs) /
Operationg Voltage (V)

[At single chip mode]

Minimum Instruction

Number of I/O Ports

Internal ROM Type

A/D Converter (ch)

D/A Converter (ch)

Synchronous Type / UART

Synchronous Type / I²C

Synchronous Type
Interrupt Sources

16-bit Timer

19-bit Timer
ROM (byte)

RAM (byte)

8-bit Timer
Category

Package
Part No.

UART

Page
I²C
0.05/2.7 - 5.5 QFP044-P-1010F 
MN101EF51A F 32K 1K 0.125/1.8 - 5.5 TQFP048-P-0707B  36 19 5 2 0 2 1 0 0 0 12   46
ADC Built-in
Type 0.05/2.7 - 5.5 TQFP032-P-0707A 
MN101EF52A F 32K 1K UBGA036-P-0404AE  24 17
0.125/1.8 - 5.5 5 2 0 1 1 0 0 0 8   48
MN101C49G 128K 4K
0.1/4.5 - 5.5
MN101C49H M 160K 6K 62.5/2.0 - 5.5
MN101C49K LQFP100-P-1414 88 23 6 1 0 2 1 1 0 0 8 4  50
MN101CF49K F 0.1/4.5 - 5.5 QFP100-P-1818B
224K 10K 0.12/4.5 - 5.5
0.1/4.5 - 5.5
MN101CP49K E 0.25/3.0 - 5.5
MN101C77A 32K 1.5K LQFP064-P-1414
0.1/2.5 - 3.6 LQFP064-P-1414
MN101C77C 48K 3K
ADC-DAC M 0.2/2.1 - 3.6 TQFP064-P-1010C
Built-in Type MN101C77D 64K 62.5/1.8 - 3.6 53 22 5 1 0 2 1 0 0 1 7 2*  52
LQFP064-P-1414
MN101C77F 96K 6K
LQFP064-P-1414
MN101CF77G F 128K 0.1/2.7 - 3.6
TQFP064-P-1010C
MN101E01J 192K
10K QFP100-P-1818B
MN101E01K 256K 0.0625/3.0 - 3.6
M 62.5/3.0 - 3.6
MN101E01L 320K 14K 84 27 7 1 0 3 2 0 0 0 8 1  54
LQFP100-P-1414
MN101E01M 20K
384K QFP100-P-1818B
MN101EF01M F 24K 0.0625/3.0 - 3.6
0.125/3.0 - 3.6
MN101C93K M
12  SEG 47
62.5/3.0 - 3.6
224K 6K LQFP100-P-1414 84 26 5 2 0 2 1 0 0 0 56
MN101CF93K F 0.167/3.0 - 3.6 COM 4
62.5/3.0 - 3.6
USB Function MN101E35A 32K
M 0.042/2.2 - 3.6
MN101E35D 68K
4K 0.0625/3.0 - 3.6 TQFP048-P-0707B 37 29 6 3 0 2 1 0 0 0 8   58
MN101EF35A 32K 62.5/2.2 - 3.6
F
MN101EF35D 64K+4K
MN101D06F 96K 3K 
0.14/4.0 - 5.5
MN101D06G M 128K 4K 61/2.2 - 5.5
MN101D06H 160K 5K QFP100-P-1818B 77 31 1 6 1 1 0 1 0 1 13  60
1
0.14/4.0 - 5.5
MN101DF06Z F 224K 6K 61/2.5 - 5.5
MN101D07G 128K 4K 0.14/4.0 - 5.5
M 61/2.2 - 5.5
MN101D07H 160K 5K LQFP112-P-2020 87 31 1 6 1 1 0 1 0 1 14 1  64
0.14/4.0 - 5.5
VTR Servo MN101DF07Z F 224K 6K 61/2.5 - 5.5
MN101D08E M 80K 2K 0.14/4.0 - 5.5
61/2.5 - 5.5 LQFP080-P-1414A 57 26 2 3 1 0 0 1 0 1 11   68
MN101DF08G F 128K 4K
MN101D09E M 80K 2K 0.14/4.0 - 5.5
61/2.5 - 5.5 QFP100-P-1818B 57 26 2 3 1 0 0 1 0 1 11   72
MN101DF09G F 128K 4K
MN101D10F 96K 2.5K
M 0.14/4.0 - 5.5
MN101D10G 3.5K 61/2.5 - 5.5 QFP100-P-1818B 77 27 2 3 1 0 0 2 0 1 12   76
128K
MN101DF10G F 4K
MN101C87A 32K 1.5K 0.1/4.5 - 5.5
M 0.25/2.7 - 5.5
MN101C87D 64K 2K 62.5/2.0 - 5.5 SEG 8 - 16
0.1/4.5 - 5.5
LQFP064-P-1414 52 21 5 1 0 1 1 0 0 0 8  DGT 18 - 10 80
MN101CF87G F 128K 4K 0.25/2.7 - 5.5
62.5/2.5 - 5.5
MN101C88D 64K 2K 0.1/4.5 - 5.5
M 0.25/2.7 - 5.5
FL Driver MN101C88G 4K 62.5/2.0 - 5.5 SEG 35 - 43
QFP100-P-1818B 88 23 5 1 0 2 1 0 0 0 8  DGT 18 - 10 82
Built-in Type 内蔵 128K 0.1/4.5 - 5.5
MN101CF88G F 10K 0.25/2.7 - 5.5
62.5/2.5 - 5.5
0.1/4.5 - 5.5
MN101CA3F M 96K 4K 0.25/2.7 - 5.5
62.5/2.0 - 5.5 SEG 35 - 43
0.1/4.5 - 5.5
QFP100-P-1818B 89 30 6 2 0 2 1 0 1 0 8  DGT 18 - 10 84
MN101CFA3G F 128K 10K 0.25/2.7 - 5.5
62.5/2.5 - 5.5
[Internal ROM type] M:Mask ROM , E:EPROM , F:FLASH
[Package] :under planning , :under development , :ES(Engineering Sample) available (All packages are lead (Pb) free.)
[*] Serves as AD pin, as well

7
 Serial Interfaces

Display Control Function

Execution Time (µs) /
Operationg Voltage (V)

[At single chip mode]

Minimum Instruction

Number of I/O Ports

Internal ROM Type

A/D Converter (ch)

D/A Converter (ch)

Synchronous Type / UART

Synchronous Type / I²C

Synchronous Type
Interrupt Sources

16-bit Timer

19-bit Timer
ROM (byte)

RAM (byte)

8-bit Timer
Category

Package
Part No.

UART

Page
I²C
MN101C38A 32K 1.5K 0.1/4.5 - 5.5
M 0.25/2.7 - 5.5
MN101C38C 125/2.0 - 5.5 LQFP100-P-1414 SEG 52
57 14 3 1 0 1 0 1 0 0 8  COM 4 86
48K 2K 0.1/4.5 - 5.5 QFP100-P-1818B
MN101CP38C E 0.25/2.7 - 5.5
125/2.3 - 5.5
0.1/4.5 - 5.5
MN101C39C M 125/2.0 - 5.5 SEG 28
48K 2K 0.1/4.5 - 5.5
TQFP080-P-1212D 61 14 3 1 0 1 0 1 0 0 8  COM 4 88
MN101CP39C E 125/2.3 - 5.5
MN101C485 8K 0.1/4.5 - 5.5
M 125/2.0 - 5.5 LQFP064-P-1414 SEG 25
MN101C487 0.5K 47 12 3 1 0 1 0 0 0 0 8  COM 4 90
16K 0.1/4.5 - 5.5 TQFP064-P-1010B
MN101CP487 E 125/2.3 - 5.5
MN101C54A 32K 0.1/4.5 - 5.5 LQFP080-P-1414A
M 0.25/2.7 - 5.5
MN101C54C 48K 62.5/2.0 - 5.5 QFP084-P-1818E
0.1/4.5 - 5.5 SEG 32
MN101CF54D F 64K 2K 0.25/4.5 - 5.5 QFP084-P-1818E 65 19 5 2 0 1 0 1 0 0 8  COM 4 92
62.5/4.5 - 5.5
0.1/4.5 - 5.5 LQFP080-P-1414A
MN101CP54C E 48K 0.25/2.7 - 5.5
QFP084-P-1818E
62.5/2.3 - 5.5
MN101C57C 48K 0.1/4.5 - 5.5
M 0.25/2.7 - 5.5
MN101C57D 62.5/2.0 - 5.5 SEG 47
2K QFP100-P-1818B 83 24 5 2 0 1 0 1 0 0 16  COM 4 96
64K 0.1/4.5 - 5.5
MN101CF57D F 0.25/2.7 - 5.5
62.5/2.5 - 5.5
MN101C589 24K 0.1/4.5 - 5.5
M 1.5K 0.25/2.7 - 5.5
MN101C58A 32K 62.5/2.0 - 5.5
0.1/4.5 - 5.5 SEG 24
MN101CF58D F 64K 2K 0.25/4.5 - 5.5 LQFP064-P-1414 49 18 5 2 0 1 0 0 0 0 8  COM 4 98
62.5/4.5 - 5.5
0.1/4.5 - 5.5
MN101CP58A E 32K 1.5K 0.25/2.7 - 5.5
62.5/2.3 - 5.5
LQFP080-P-1414A
MN101C66D 64K 2K 0.1/4.5 - 5.5 QFP084-P-1818E
M 0.25/2.7 - 5.5
62.5/2.0 - 5.5 LQFP080-P-1414A 
MN101C66G
QFP084-P-1818E
128K 4K 65 19 5 2 0 1 0 1 0 0 8 SEG 32 100
0.1/4.5 - 5.5  COM 4
MN101CF66G F 0.25/2.7 - 5.5
LCD Driver 62.5/2.5 - 5.5 LQFP080-P-1414A
Built-in Type 0.1/4.5 - 5.5 QFP084-P-1818E
MN101CP66D E 64K 2K 0.25/2.7 - 5.5
62.5/2.3 - 5.5
0.1/3.0 - 3.6
MN101C70C M 48K 2K 0.235/1.8 - 3.6 LQFP080-P-1414A
16  SEG
62.5/1.8 - 3.6 32
66 20 6 2 0 1 1 0 0 0 104
0.25/3.0 - 3.6 COM 4
MN101CF70D F 64K 4K 0.50/2.2 - 3.6 LQFP080-P-1414A 
62.5/2.2 - 3.6
0.1/3.0 - 3.6
MN101C73A M 1.5K 0.235/1.8 - 3.6
62.5/1.8 - 3.6 LQFP064-P-1414 SEG 32
32K 0.1/3.0 - 3.6 TQFP064-P-1010C 55 24 5 2 0 2 1 0 0 0 12  COM 4 106
MN101CF73A F 2K 0.235/2.2 - 3.6
62.5/2.2 - 3.6
MN101C74F 96K 0.1/3.0 - 3.6
M 0.235/1.8 - 3.6
LQFP100-P-1414
MN101C74G
16  SEG
62.5/1.8 - 3.6 47
6K MLGA100-L-1010 86 26 5 2 0 2 1 0 0 1 COM 4 108
128K 0.1/3.0 - 3.6
QFP100-P-1818B
MN101CF74G F 0.235/2.2 - 3.6
62.5/2.2 - 3.6
0.1/3.0 - 3.6
0.118/2.7 - 3.6
MN101C78A M 0.235/1.8 - 3.6 SEG 12
32K 1.5K 62.5/1.8 - 3.6 TQFP048-P-0707B 39 22 5 2 0 2 1 0 0 1 7  COM 4 110
0.118/3.0 - 3.6
MN101CF78A F 62.5/2.2 - 3.6
0.1/4.5 - 5.5
MN101C84A M 32K 1K 0.25/2.7 - 5.5
62.5/2.0 - 5.5 SEG 32
0.1/4.5 - 5.5
LQFP064-P-1414 52 18 5 2 0 1 0 0 0 0 8  COM 4 112
MN101CF84D F 64K 2K 0.25/2.7 - 5.5
62.5/2.5 - 5.5
MN101CA27 M 16K 0.5K 0.25/2.7 - 3.6 SEG 32
0.50/1.8 - 3.6 LQFP064-P-1414 25 8 3 0 0 0 0 0 0 0   COM 4 114
MN101CFA2D F 64K 2K 62.5/1.8 - 3.6
MN101E29G M 128K LQFP100-P-1414 SEG 55
6K 0.05/2.2 - 5.5
QFP100-P-1818B 90 28 7 3 0 4 1 0 0 1 16 4 COM 4 116
MN101EF29G F 128K+4K
MN101E31D 64K 4K
M 0.05/2.2 - 5.5
MN101E31G 128K 6K
12  SEG 41
LQFP080-P-1414A 70 23 7 2 0 3 1 0 0 1 118
MN101EF31D 64K+8K 4K 0.05/2.7 - 5.5 COM 4
F
MN101EF31G 128K+4K 6K 0.05/2.2 - 5.5
SEG 32
MN101EF32D F 64K+8K 4K 0.05/2.7 - 5.5 LQFP064-P-1414 54 23 7 2 0 2 1 0 0 1 8  COM 4 120

8
 Serial Interfaces

Display Control Function

Execution Time (µs) /
Operationg Voltage (V)

[At single chip mode]

Minimum Instruction

Number of I/O Ports

Internal ROM Type

A/D Converter (ch)

D/A Converter (ch)

Synchronous Type / UART

Synchronous Type / I²C

Synchronous Type
Interrupt Sources

16-bit Timer

19-bit Timer
ROM (byte)

RAM (byte)

8-bit Timer
Category

Package
Part No.

UART

Page
I²C
MN101E46G 128K TQFP128-P-1414C 
4K 0.1/2.2 - 3.6
MN101E46N M 508K SEG 64
0.125/1.8 - 3.6 TQFP128-P-1414C  67 21 5 2 0 1 1 0 0 0 3  COM 32 122
MN101E46R 6K 61/1.8 - 3.6
928K
MN101EF46R F 8K TQFP128-P-1414A 
LCD Driver 0.05/2.7 - 5.5 LQFP100-P-1414  90 34 SEG 55
Built-in Type MN101EF56G F 128K 6K 7 3 0 3 1 0 0 0 24 4 124
0.1/1.8-5.5 QFP100-P-1818B  COM 4
LQFP080-P-1414A 16 2 SEG
MN101EF57G 0.05/2.7 - 5.5  70 34 41
F 128K 6K 7 3 0 3 1 0 0 0 126
0.1/1.8-5.5 TQFP080-P-1212D  COM 4
LQFP064-P-1414
0.05/2.7 - 5.5
12  SEG 32
 54 34
MN101EF58G F 128K 6K TQFP064-P-1010C 7 3 0 3 1 0 0 0 128
0.1/1.8-5.5  COM 4
MN101E30N 508K
M SEG 55
MN101E30R 8K 0.05/2.2 - 5.5 QFP100-P-1818B 85 30 7 3 0 4 1 0 0 1 12 5 130
928K COM 4
Voice control MN101EF30R F
MN101E59R M SEG 55
928K 8K 0.05/2.2 - 5.5 QFP100-P-1818B 85 30 7 3 0 4 1 0 0 1 12 5
COM 4 132
MN101EF59R F
MN101EF41N F 512K 30K 0.05/3.0 - 3.6 QFP100-P-1818B  85 29 9 1 0 3 2 0 0 0 8   134
MN101E49K M 256K 12K 0.05/3.0 - 3.6 LQFP100-P-1414 
In-vehicle 30.6/2.7 - 3.6 85 29 9 1 0 3 2 0 0 0 8   136
networking MN101EF49N F 512K 30K LQFP100-P-1414
SEG 32
MN101EF63G F 128K 10K 0.05/2.7 - 5.5 TQFP064-P-1010C  54 34 7 3 0 3 1 0 0 0 12  COM 4 138
[Internal ROM type] M:Mask ROM , E:EPROM , F:FLASH
[Package] :under planning , :under development , :ES(Engineering Sample) available (All packages are lead (Pb) free.)

 AM2(MN102) 16-bit Single-chip Microcontroller Series

Serial Interfaces
Operationg Voltage (V)

Synchronous Type / UART

Synchronous Type / UART / I²C

Execution Time (µs) /
Minimum Instruction

Number of I/O Ports

Internal ROM Type

A/D Converter (ch)

D/A Converter (ch)

Synchronous Type
Interrupt Sources

16-bit Timer

24-bit Timer
ROM (byte)

RAM (byte)

8-bit Timer
Category

Package
Part No.

Page
I²C

MN102H460B 0.05/3.0 - 3.6 LQFP128-P-1818C

  4K 63 54 16 5 1 3 2 0 0 12  142
0.1/2.0 - 3.6 TQFP128-P-1414B
MN102H60G LQFP100-P-1414
128K 4K
M MLGA100-L-1010
ADC MN102H60K 256K 10K 0.058/3.0 - 3.6 LQFP100-P-1414
82 50 10 6 0 0 2 3 0 8  144
Built-in Type 62.5/3.0 - 3.6 LQFP100-P-1414
MN102HF60G 128K 4K MLGA100-L-1010
F
MN102HF60K 256K 10K LQFP100-P-1414
MN102L59D M
64K 2K 0.1/4.5 - 5.5 LQFP064-P-1414 52 24 9 3 0 2 0 0 0 12  146
MN102LF59D F
MN102H730FGT   TQFP128-P-1414B 66
10K
MN102H73G 128K
M 0.058/3.0 - 3.6 TQFP128-P-1414A
MN102H73K 256K 12K 50 10 5 0 2 2 0 0 12 4 148
ADC-DAC 62.5/3.0 - 3.6 105
Built-in Type MN102HF73G 128K 10K
F TQFP128-P-1414B
MN102HF73K 256K 12K
MN102H950F 0.058/3.0 - 3.6
  10K LQFP100-P-1414 63 47 10 5 0 2 2 0 0 12 4 150
62.5/3.0 - 3.6
MN102H74D 64K
M 0.0833/3.0 - 3.6
USB Function MN102H74G 4K LQFP100-P-1414 77 54 10 4 0 2 2 0 0 8  152
128K 62.5/3.0 - 3.6
MN102HF74G F
[Internal ROM type] M:Mask ROM , E:EPROM , F:FLASH , :External
[Package] :under planning , :under development , :ES(Engineering Sample) available (All packages are lead (Pb) free.)

9
 AM3(MN103) 32-bit Single-chip Microcontroller Series
Serial

CPU Performance (MIPS/MHz)

Interfaces

Operationg Voltage (V)

Execution Time (ns) /

Synchronous Type / UART / I²C

Minimum Instruction

Number of I/O Ports

Synchronous Type / UART

Motor Control PWM

DMA Controller (ch)

Internal ROM Type

Interrupt Sources
[Dhrystone2.1]

A/D Converter

Bus Interface
16-bit Timer

32-bit Timer
ROM (byte)

RAM (byte)

8-bit Timer
Category

Package

Page
Type

I²C
MN103SFB5K F 256K 8K 38/48 16.7/2.7 - 3.6 LQFP064-P-1414 42 35 4 2 0 0 2 0 1  4  156
USB HOST

MN103SFE5P F 624K 32K 48/48 20.83/3.0 - 3.6 LQFP048-P2-0707A 27 48 6 2 0 0 4 0 2  5  158

MN103SG20L   32K 48/48 20.83/3.0 - 3.6 QFP100-P-1818B  44 59 6 2 0 0 5 0 3  5 Data: 16-bit 160
MN103SFH7J F
192K 8K 38/48 16.7/2.7 - 3.6 TQFP064-P-1010C 42 35 4 2 0 0 2 0 1  4  162
MN103SH7J M
LQFP100-P-1414  81 84 14
MN103LF06N F 512K 32K 38/40 25/2.6 - 3.6 6 0 0 6 3 0 15-ch×1 4 Data:access
8-bit/16-bit
164
QFP100-P-1818B 
MN103S57G M Data: 8-bit/16-bit
128K 16K 40/40 25/3.0 - 3.6 LQFP100-P-1414A 73 64 10 6 0 0 3 2 0 12-ch×1 4 access 166
MN103SF57G F
MN103SF73N 512K
AV control applications

Data: 8-bit/16-bit
access
F 32K 40/40 25/2.7 - 3.6 QFP100-P-1818B 82 71 10 6 0 0 2 3 0 8-ch×1 4 SDRAM interface 168
MN103SF73R 1024K
supporting
MN103S97N M 512K 24K Data: 8-bit/16-
40/40 25/2.7 - 3.6 MBGA255-C-1111A 195 106 16 12 0 0 7 0 1 25-ch×1 4 bit/32-bit access 170
MN103SF66R F 1024K 40K
MN103SB9N M 512K Data: 8-bit/16-bit
access
32K 48/60 16.7/2.7 - 3.6 TQFP128-P-1414A 104 68 10 6 0 0 2 3 0 12-ch×1 4 SDRAM interface 174
MN103SFB9R F 1024K
supporting
MN103SD0Q M 768K 32K
48/60 16.7/2.7 - 3.6 UBGA257-P-1111A 195 116 8 12 0 0 11 0 2 32-ch×1 6 Data:access
8-bit/16-bit
176
MN103SFD0R F 1024K 40K
MN103SD3P M 640K 40K
48/60 16.7/2.7 - 3.6 LQFP100-P-1414 82 82 13 6 0 0 5 3 0 8-ch×1 4 Data:access
8-bit/16-bit
178
MN103SFD3R F 1024K 64K
MN103SC2A 32K
M 2unit
MN103SC2D 4K 48/60 16.7/4.5 - 5.5 QFP044-P-1010F 29 28 4 2 0 1 1 0 0   180
64K 8-ch
MN103SFC2D F
3unit
Invertor motor control

MN103SFC6K F 256K 40K 70/70 14.3/3.0 - 5.5 QFP100-P-1818B 81 56 12 6 0 2 3 1 0   182

20-ch
MN103SE3K M 3unit
256K 8K 48/60 16.7/4.5 - 5.5 QFP100-P-1818B 81 56 12 6 0 2 3 0 0   184
MN103SFE3K F 20-ch
MN103SE4D 64K
4K
MN103SE4G M 128K
3unit
MN103SE4K 256K 8K 48/60 16.7/4.5 - 5.5 LQFP080-P-1414A 61 56 12 6 0 2 3 0 0   186
16-ch
MN103SFE4G 128K 4K
F
MN103SFE4K 256K 8K
3unit
MN103SFG5K F 256K 12K 48/60 16.7/4.5 - 5.5 LQFP128-P-1818C 112 81 16 9 0 3 3 1 0 28-ch   188
LQFP128-P-1818C  109
15-ch×1
MN103LF03R F 1024K 63.5K 38/40 25/2.7 - 3.6 LQFP144-P-2020A  123 84 14 6 0 0 6 3 0 4 Data:access
8-bit/16-bit
190
networking
In-vehicle

QFP100-P-1818B  81 8-ch×1
LQFP128-P-1818C  104
MN103LF04R F 1024K 63.5K 38/40 25/2.7 - 3.6 81 14 6 0 0 6 3 0 15-ch×1 4 Data:access
8-bit/16-bit
194
LQFP144-P-2020A  118
Data: 8-bit/16-bit
MN103SFA2R F 1024K 64K 48/60 16.7/2.7 - 3.6 LQFP100-P-1414  82 84 13 6 0 0 5 3 0 8-ch×1 4 access 198
[Internal ROM type] M:Mask ROM , E:EPROM , F:FLASH , :External
[Package] :under planning , :under development , :ES(Engineering Sample) available (All packages are lead (Pb) free.)

10
 AM1 (MN101) Series

The AM1 Series of 8-bit microcomputers allows short-time program

development in the C programming language.
Its half-byte instruction set and other architectural features yield ROM
code sizes that are small enough to rival those achieved with assembly
language.
These devices are compact and have low power consumptions, yet
offer high-speed operation with a minimum instruction execution time of
100 ns (at 5 V,3 V : MN101C Series) and 50 ns(at 5 V, 3 V : MN101E
Series).
These microcomputers are suitable for a wide range of applications
demanding high cost performance.

Features
• Efficiency of C-based ROM code: Assembler rate 1 or less
• Linear address space: 1 MB
• Identical architecture for 32-bit and 16-bit microcomputers
• Option functions
Hardware task switching (Max. 4 task)
16-bit multiplication
ROM collection
 Application
 MN101C28 Series
Type MN101C28A MN101C28C MN101C28D MN101C28F MN101C28L MN101CP28D MN101CP28L
Internal ROM type Mask ROM EPROM
ROM (byte) 32K 48K 64K 96K 64K 96K
RAM (byte) 1.5K 2K 4K 10K 2K 10K
LQFP080-P-1414A, LQFP080-P-1414A,
Package (Lead-free) QFP084-P-1818E, LQFP080-P-1414A QFP084-P-1818E, LQFP080-P-1414A
TQFP080-P-1212D TQFP080-P-1212D
0.10 µs (at 4.5 V to 5.5 V, 20 MHz)
0.238 µs (at 2.6 V to 5.5 V, 8.39 MHz)
Minimum Instruction 0.333 µs (at 2.3 V to 5.5 V, 6 MHz)
Execution Time 1.00 µs (at 2.0 V to 5.5 V, 2 MHz)*
125 µs (at 2.0 V to 5.5 V, 32.768 kHz)*
*: The lower limit for operation guarantee for EPROM built-in type is 2.3 V.

 Interrupts
RESET. Watchdog. External 0 to 4. Timer 0 to 5. Time base. Serial 0 to 2. Automatic transfer finish. A/D conversion finish

 Timer Counter
8-bit timer × 4
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 4 ..................Square-wave/16-bit PWM output. Event count. Synchronous output event. Input capture
Time base timer: One-minute count setting. Independently operable 8-bit timer 5
Watchdog timer × 1

 Serial interface
Synchronous type/Simple UART (half-duplex) × 1: Serial 0
Synchronous type × 1: Serial 1
Synchronous type/Single-master I2C × 1: Serial 2

 I/O Pins
I/O 57 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
Input 13 : Common use. Specified pull-up resistor available

 A/D converter
10-bit × 8 channels (with S/H)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 25 50 mA
Operating supply current
IDD2 fx = 32.768 kHz. VDD = 3 V 40 120 µA
fx = 32.768 kHz. VDD = 3 V. Ta = 25 °C 4 8 µA
Supply current at HALT IDD3
fx = 32.768 kHz. VDD = 3 V. Ta = 85 °C 20 µA
VDD = 5 V. Ta = 25 °C 1 µA
Supply current at STOP IDD4
VDD = 5 V. Ta = -40 °C to +85 °C 30 µA

12 MAD00006JEM
 MN101C28A, MN101C28C, MN101C28D, MN101C28F, MN101C28L, MN101CP28D, MN101CP28L

 Pin Assignment
LQFP080-P-1414A, TQFP080-P-1212D [MN101C28A/28C/28D]

P37, /DKDMA

P35, /LDDMA
P36, /STDMA
P47, KEY7
P46, KEY6
P45, KEY5
P44, KEY4
P43, KEY3
P42, KEY2
P41, KEY1
P40, KEY0
P50, /WE
P54, A17
P53, A16

P51, /RE
P52, /CS
P63, A3
P62, A2
P61, A1
P60, A0
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
P64, A4 61 40 /BT, P34
P65, A5 62 39 /BR, P33
P66, A6 63 38 SBT2, P32
P67, A7 64 37 SBI2, P31
SDO0, P70, A8 65 36 SBO2, P30
SDO1, P71, A9 66 35 IRQ4, P24
SDO2, P72, A10 67 34 IRQ3, P23
SDO3, P73, A11 68 33 IRQ2, P22
SDO4, P74, A12 69 32 SENS, IRQ1, P21
SDO5, P75, A13 70 31 IRQ0, P20
SDO6, P76, A14 71 30 TM4IO, P14
SDO7, P77, A15 72 29 TM3IO, P13
P87, LED7, D7 73 28 TM2IO, P12
P86, LED6, D6 74 27 TM1IO, P11
P85, LED5, D5 75 26 RMOUT, TM0IO, P10
P84, LED4, D4 76 25 /RST, P27
P83, LED3, D3 77 24 /DK, BUZZER, P06
P82, LED2, D2 78 23 SBT1, P05
P81, LED1, D1 79 22 SBI1, P04
P80, LED0, D0 80 21 SBO1, P03
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9
VREF-

VREF+
VDD
OSC2
OSC1
VSS
XI
XO
MMOD
TXD, SBO0, P00
RXD, SBI0, P01
SBT0, P02
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6
AN7, PA7

QFP084-P-1818E
P37, NDKDMA

P35, NLDDMA
P36, NSTDMA
P47, KEY7
P46, KEY6
P45, KEY5
P44, KEY4
P43, KEY3
P42, KEY2
P41, KEY1
P40, KEY0
P50, NWE
P51, NRE
P52, NCS
P54, A17
P53, A16
P63, A3
P62, A2
P61, A1
P60, A0

N.C.
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43

P64, A4 64 42 NBT, P34

P65, A5 65 41 NBR, P33
P66, A6 66 40 SBT2, P32
P67, A7 67 39 SBI2, P31
SDO0, P70, A8 68 38 SBO2, P30IRQ4, P24
SDO1, P71, A9 69 37 IRQ4, P24
SDO2, P72, A10 70 36 IRQ3, P23
SDO3, P73, A11 71 35 IRQ2, P22
SDO4, P74, A12 72 34 SENS, IRQ1, P21
SDO5, P75, A13 73 33 IRQ0, P20
SDO6, P76, A14 74 32 N.C.
SDO7, P77, A15 75 31 TM4IO, P14
N.C. 76 30 TM3IO, P13
P87, LED7, D7 77 29 TM2IO, P12
P86, LED6, D6 78 28 TM1IO, P11
P85, LED5, D5 79 27 RMOUT, TM0IO, P10
P84, LED4, D4 80 26 NRST, P27
P83, LED3, D3 81 25 NDK, BUZZER, P06
P82, LED2, D2 82 24 SBT1, P05
P81, LED1, D1 83 23 SBI1, P04
P80, LED0, D0 84 22 SBO1, P03
10

12
13
14
15
16
17
18
19
20
21
11
1
2
3
4
5
6
7
8
9
VREF-

VREF+
VDD
N.C.
OSC2
OSC1
VSS
XI
XO
MMOD
TXD, SBO0, P00
RXD, SBI0, P01
SBT0, P02
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6
AN7, PA7

MAD00006JEM 13
 MN101C30 Series
Type MN101C309 MN101C30A MN101CP30A
Internal ROM type Mask ROM EPROM
ROM (byte) 24K 32K
RAM (byte) 1K 1.5K
Package (Lead-free) LQFP064-P-1414
0.10 µs (at 4.5 V to 5.5 V, 20 MHz)
0.238 µs (at 2.7 V to 5.5 V, 8.39 MHz)
Minimum Instruction 1.00 µs (at 2.0 V to 5.5 V, 2 MHz)*
Execution Time 125 µs (at 2.0 V to 5.5 V, 32.768 kHz)*
*: The lower limit for operation guarantee for EPROM built-in type is 2.7 V.

 Interrupts
RESET. Watchdog. External 0 to 4. Timer 0 to 5. Time base. Serial 0. Serial 1. Automatic transfer finish. A/D conversion finish

 Timer Counter
8-bit timer × 4
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 4 ..................Square-wave/16-bit PWM output. Event count. Synchronous output event. Input capture
Time base timer: One-minute count setting. Independently operable 8-bit timer 5
Watchdog timer × 1

 Serial interface
Synchronous type/Simple UART (half-duplex) × 1: Serial 0
Synchronous type × 1: Serial 1

 I/O Pins
I/O 41 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
Input 13 : Common use. Specified pull-up resistor available

 A/D converter
10-bit × 8 channels (with S/H)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 25 60 mA
Operating supply current
IDD2 fx = 32.768 kHz. VDD = 3 V 30 100 µA
fx = 32.768 kHz. VDD = 3 V. Ta = 25 °C 4 8 µA
Supply current at HALT IDD3
fx = 32.768 kHz. VDD = 3 V. Ta = 85 °C 18 µA
VDD = 5 V. Ta = 25 °C 2 µA
Supply current at STOP IDD4
VDD = 5 V. Ta = -40 °C to +85 °C 20 µA

14 MAD00005JEM
 MN101C309, MN101C30A, MN101CP30A

 Pin Assignment
LQFP064-P-1414

A10, P72, SDO2

A11, P73, SDO3

A9, P71, SDO1

A8, P70, SDO0

P54, A17
P53, A16

P51, /RE
P52, /CS
P67, A7
P66, A6
P65, A5
P64, A4
P63, A3
P62, A2
P61, A1
P60, A0
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
SDO4, A12, P74 49 32 P50, /WE
SDO5, A13, P75 50 31 P24, IRQ4
SDO6, A14, P76 51 30 P23, IRQ3
SDO7, A15, P77 52 29 P22, IRQ2
LED7, D7, P87 53 28 P21, IRQ1, SENS
LED6, D6, P86 54 27 P20, IRQ0
LED5, D5, P85 55 26 P14, TM4IO
LED4, D4, P84 56 25 P13, TM3IO
LED3, D3, P83 57 24 P12, TM2IO
LED2, D2, P82 58 23 P11, TM1IO
LED1, D1, P81 59 22 P10, TM0IO, RMOUT
LED0, D0, P80 60 21 P27, /RST
VREF- 61 20 P06, BUZZER, /DK
AN0, PA0 62 19 SBT1, P05
AN1, PA1 63 18 SBI1, P04
AN2, PA2 64 17 SBO1, P03
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9
VREF+
VDD
OSC2
OSC1
VSS
XI
XO
MMOD
P00, SBO0, TXD
P01, SBI0, RXD
P02, SBT0
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6
AN7, PA7

MAD00005JEM 15
 MN101C42 Series
Type MN101C425 MN101C427 MN101CP427
Internal ROM type Mask ROM EPROM
ROM (byte) 8K 16K
RAM (byte) 0.25K 0.5K
Package (Lead-free) QFP044-P-1010F, SDIP042-P-0600C, TQFP048-P-0707B
0.10 µs (at 4.5 V to 5.5 V, 20 MHz)
0.238 µs (at 2.7 V to 5.5 V, 8.39 MHz)
Minimum Instruction 0.477 µs (at 2.0 V to 5.5 V, 4.19 MHz)*
Execution Time 125 µs (at 2.0 V to 5.5 V, 32.768 kHz)*
*: The lower limit for operation guarantee for EPROM built-in type is 2.7 V.

 Interrupts
RESET. Watchdog. External 0 to 2. External 3 (only 48-pin package). Timer 2 to 5. Time base. Serial 0. A/D conversion finish

 Timer Counter
8-bit timer × 2
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 4 ..................Square-wave/16-bit PWM output. Event count. Synchronous output event. Input capture
Time base timer: One-minute count setting. Independently operable 8-bit timer 5
Watchdog timer × 1

 Serial interface
Synchronous type/Simple UART (half-duplex) × 1: Serial 0

 I/O Pins
I/O 27 : Common use: 16. Specified pull-up resistor available
Input/output selectable (bit unit): 26 (for 44-pin). 25 (for 42-pin)
Input 12 : Common use. Specified pull-up resistor available

 A/D converter
10-bit × 8 channels (with S/H)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 15 40 mA
Operating supply current IDD2 fosc = 8.39 MHz. VDD = 5 V 6 18 mA
IDD3 fx = 32.768 kHz. VDD = 3 V 100 µA
IDD4 fx = 32.768 kHz. VDD = 3 V. Ta = 25 °C 8 µA
Supply current at HALT
IDD5 fx = 32.768 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 18 µA
VDD = 5 V. Ta = 25 °C 2 µA
Supply current at STOP IDD6
VDD = 5 V. Ta = -40 °C to +85 °C 20 µA

16 MAD00002JEM
MAD00002JEM
QFP044-P-1010F
 Pin Assignment
SDIP042-P-0600C

TQFP048-P-0707B

NRST, P27

LED4, P84
LED5, P85
LED6, P86
LED7, P87
MMOD
P71
P70
P67
P66
P65
P64
NRST, P27

LED4, P84
LED5, P85
LED6, P86
LED7, P87
MMOD
P70
P67
P66
P65
P64
TXD, SBO0, P00 1 42 VSS
RXD, SBI0, P01 2 41 OSC1
SBT0, P02 3 40 OSC2
BUZZER, P06 4 39 VDD

48
47
46
45
44
43
42
41
40
39
38
37
44
43
42
41
40
39
38
37
36
35
34
RMOUT, P10 5 38 PA7, AN7
LED3, P83 1 36 P63
LED3, P83 1 33 P63 P11 6 37 PA6, AN6
LED2, P82 2 35 P62
LED2, P82 2 32 P62 TMIO2, P12 7 36 PA5, AN5
LED1, P81 3 34 P61
LED1, P81 3 31 P61 TMIO3, P13 8 35 PA4, AN4
LED0, P80 4 33 P60
LED0, P80 4 30 P60 TMIO4, P14 9 34 PA3, AN3
N.C. 5 32 P23, IRQ3
AN0, PA0 5 29 P22, IRQ2 IRQ0, P20 10 33 PA2, AN2
AN0, PA0 6 31 P22, IRQ2
AN1, PA1 6 28 P21, IRQ1 IRQ1, P21 11 32 PA1, AN1
AN1, PA1 7 30 P21, IRQ1, SENS
AN2, PA2 7 27 P20, IRQ0 IRQ2, P22 12 31 PA0, AN0
AN2, PA2 8 29 P20, IRQ0
AN3, PA3 8 26 P14, TMIO4 P60 13 30 P80, LED0
AN3, PA3 9 28 P14, TMIO4
AN4, PA4 9 25 P13, TMIO3 P61 14 29 P81, LED1
AN4, PA4 10 27 P13, TMIO3
AN5, PA5 10 24 P12, TMIO2 P62 15 28 P82, LED2
AN5, PA5 11 26 P12, TMIO2
AN6, PA6 11 23 P11 P63 16 27 P83, LED3
AN6, PA6 12 25 P11

12
13
14
15
16
17
18
19
20
21
22
P64 17 26 P84, LED4

13
14
15
16
17
18
19
20
21
22
23
24
P65 18 25 P85, LED5
P66 19 24 P86, LED6
P67 20 23 P87, LED7
NRST, P27 21 22 MMOD

XI
XO
VSS
N.C.

VSS
VDD

VDD
OSC2
OSC1

OSC2
OSC1
PA7, AN7
P02, SBT0

PA7, AN7
P02, SBT0
P10, RMOUT

P10, RMOUT
P06, BUZZER

P06, BUZZER
P01, SBI0, RXD

P01, SBI0, RXD

P00, SBO0, TXD

P00, SBO0, TXD

MN101C425, MN101C427, MN101CP427

17
 MN101C45 Series
Type MN101C457 MN101CP427
Internal ROM type Mask ROM EPROM
ROM (byte) 16K
RAM (byte) 0.5K
Package (Lead-free) QFP044-P-1010F
0.10 µs (at 4.5 V to 5.5 V, 20 MHz)
Minimum Instruction 0.10 µs (at 4.5 V to 5.5 V, 20 MHz)
0.238 µs (at 2.7 V to 5.5 V, 8.39 MHz)
Execution Time 0.238 µs (at 2.7 V to 5.5 V, 8.39 MHz)
0.477 µs (at 2.0 V to 5.5 V, 4.19 MHz)

 Interrupts
RESET. Watchdog. External 0 to 2. Timer 2 to 5. Time base. Serial 0. A/D conversion finish

 Timer Counter
8-bit timer × 2
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 4 ..................Square-wave/16-bit PWM output. Event count. Synchronous output event. Input capture
Time base timer: One-minute count setting. Independently operable 8-bit timer 5
Watchdog timer × 1

 Serial interface
Synchronous type/Simple UART (half-duplex) × 1: Serial 0

 I/O Pins
I/O 26 : Common use: 16. Specified pull-up resistor available. Input/output selectable (bit unit): 26
Input 11 : Common use. Specified pull-up resistor available

 A/D converter
10-bit × 8 channels (with S/H)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 15 40 mA
Operating supply current
IDD2 fosc = 8.39 MHz. VDD = 5 V 6 18 mA
IDD3 VDD = 5 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD4 VDD = 5 V. Ta = -40 °C to +85 °C 20 µA

18 MAD00003LEM
 MN101C457, MN101CP427

 Pin Assignment
QFP044-P-1010F

P14, TMIO4
P13, TMIO3
P12, TMIO2
P22, IRQ2
P21, IRQ1
P20, IRQ0
P63
P62
P61
P60

P11
33
32
31
30
29
28
27
26
25
24
23
P64 34 22 P10, RMOUT
P65 35 21 P06, BUZZER
P66 36 20 P02, SBT0
P67 37 19 P01, SBI0, RXD
P70 38 18 P00, SBO0, TXD
NRST, P27 39 17 N.C.
MMOD 40 16 VSS
LED7, P87 41 15 OSC1
LED6, P86 42 14 OSC2
LED5, P85 43 13 VDD
LED4, P84 44 12 PA7, AN7

10
11
1
2
3
4
5
6
7
8
9
LED3, P83
LED2, P82
LED1, P81
LED0, P80
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6

MAD00003LEM 19
 MN101C53 Series
Type MN101C539 MN101CP539
Internal ROM type Mask ROM EPROM
ROM (byte) 24K (External memory can not be expanded)
RAM (byte) 0.5K (External memory can not be expanded)
Package (Lead-free) TQFP048-P-0707B
[High speed mode]
0.10 µs (at 4.5 V to 5.5 V, 20 MHz)
0.238 µs (at 2.7 V to 5.5 V, 8.39 MHz)
Minimum Instruction 1.00 µs (at 2.0 V to 5.5 V, 4 MHz)*
Execution Time [Low speed mode]
61.04 µs (at 2.0 V to 5.5 V, 32.768 kHz)*
*: The lower limit for operation guarantee for EPROM built-in type is 2.7 V.

 Interrupts
RESET. Watchdog. External 0 to 3. Timer 2. Timer 3. Timer 6. Timer 7 (2 systems). Time base. Serial 0 (2 systems). A/D conversion
finish

 Timer Counter
8-bit timer × 3
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event. Pulse width measurement
Timer 3 ..................Square-wave output. Event count. Remote control carrier output
Timer 6 ..................8-bit freerun timer
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
width measurement. Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0

 I/O Pins
I/O 36 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
Input 4 : Common use. Specified pull-up resistor available

 A/D converter
10-bit × 8 channels (with S/H)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 20 50 mA
Operating supply current IDD2 fosc = 8.39 MHz. VDD = 5 V 10 20 mA
IDD3 fx = 32.768 kHz. VDD = 3 V 20 70 µA
IDD4 fx = 32.768 kHz. VDD = 3 V. Ta = 25 °C 2 6 µA
Supply current at HALT
IDD5 fx = 32.768 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 15 µA
VDD = 5 V. Ta = 25 °C 2 µA
Supply current at STOP IDD6
VDD = 5 V. Ta = -40 °C to +85 °C 20 µA

20 MAD00004HEM
 MN101C539, MN101CP539

 Pin Assignment
TQFP048-P-0707B

P21, IRQ1, SENS

P14, TM7IO
P13, TM3IO
P12, TM2IO
P11, TM7O
P63, KEY3
P62, KEY2
P61, KEY1
P60, KEY0
P23, IRQ3
P22, IRQ2

P20, IRQ0
36
35
34
33
32
31
30
29
28
27
26
25
KEY4, P64 37 24 P10, RMOUT, TM7PWM
KEY5, P65 38 23 P06, BUZZER
KEY6, P66 39 22 P02, SBT0
KEY7, P67 40 21 P01, SBI0, RXD
P70 41 20 P00, SBO0, TXD
P71 42 19 XO
NRST, P27 43 18 XI
MMOD 44 17 VSS
LED7, P87 45 16 OSC1
LED6, P86 46 15 OSC2
LED5, P85 47 14 VDD
LED4, P84 48 13 PA7, AN7

10

12
11
1
2
3
4
5
6
7
8
9
LED3, P83
LED2, P82
LED1, P81
LED0, P80
PC0
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6

MAD00004HEM 21
 MN101C61 Series
Type MN101C61D MN101C61G MN101CF60G MN101CF61G
Internal ROM type Mask ROM FLASH
ROM (byte) 64K 128K
RAM (byte) 3K 12K
Package (Lead-free) TQFP080-P-1212D
[Standard]
0.1 µs (at 2.5 V to 3.6 V, 20 MHz)
0.2 µs (at 2.1 V to 3.6 V, 10 MHz)
0.5 µs (at 1.8 V to 3.6 V, 4 MHz)*
125 µs (at 1.8 V to 3.6 V, 32 kHz)*
Minimum Instruction [Double speed]
Execution Time 0.1 µs (at 2.5 V to 3.6 V, 10 MHz)
0.2 µs (at 2.1 V to 3.6 V, 5 MHz)
0.5 µs (at 1.8 V to 3.6 V, 2 MHz)*
62.5 µs (at 1.8 V to 3.6 V, 32 kHz)*
*: The operation guarantee range for flash memory built-in type is 2.2 V to 3.0 V (MN101CF60G) or 2.7 V
to 3.6 V (MN101CF61G).

 Interrupts
RESET. Watchdog. External 0 to 5. Timer 0 to 6. Timer 7 (2 systems). Time base. Serial 0 reception. Serial 0 transmission. Serial 1
reception. Serial 1 transmission. Serial 2. Serial 3. Automatic transfer finish. A/D conversion finish. Key interrupts (8 lines)

 Timer Counter
8-bit timer × 7
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Pulse width measurement
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event. Pulse width measurement
Timer 3 ..................Square-wave output. Event count. Remote control carrier output
Timer 4 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial 1 baud rate timer
Timer 5 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial 0 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
width measurement. Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type × 1: Serial 2
Synchronous type/Single-master I2C × 1: Serial 3

 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 62 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
Input 6 : Common use. Specified pull-up resistor available

 A/D converter
10-bit × 6 channels (with S/H)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 3 addresses possible

22 MAD00009KEM
 MN101C61D, MN101C61G, MN101CF60G, MN101CF61G

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz (fs = fosc/2). VDD = 3 V 5 12 mA
Operating supply current IDD2 fosc = 8.39 MHz (fs = fosc/2). VDD = 3 V 2 5 mA
IDD3 fx = 32.768 kHz (fs = fx/2). VDD = 3 V 40 µA
IDD4 fx = 32.768 kHz. VDD = 3 V. Ta = 25 °C 4 8 µA
Supply current at HALT
IDD5 fx = 32.768 kHz. VDD = 3 V 30 µA
IDD6 VDD = 3 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD7 VDD = 3 V 20 µA
Ta = -40 °C to +85 °C. VDD = 1.8 V to 3.6 V. VSS = 0 V
Note) Ta = -20 °C to +70 °C for a flash memory built-in version.
Supply voltage range and supply current ratings are also different from the values mentioned above.
Refer to Chapter 18 "Flash EEPROM" for detailes.

 Pin Assignment
TQFP080-P-1212D

P40, TXD0, SBO0, KEY0

P41, RXD0, SBI0, KEY1

P37, TCIO4, NDKDMA

P43, TCIO5, KEY3
P42, SBT0, KEY2
P47, KEY7, A15
P46, KEY6, A14
P52, IRQ5, NCS

P35, NLDDMA
P45, KEY5, A9
P44, KEY4, A8

P36, NSTDMA
P50, NWE
P51, NRE
P54, A17
P53, A16
P63, A3
P62, A2
P61, A1
P60, A0
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41

P64, A4 61 40 NBT, P34

P65, A5 62 39 NBR, P33
P66, A6 63 38 SBT3, P32
P67, A7 64 37 SYSCLK, SBI3, P31
P70, SDO0 65 36 SBO3, P30
P71, SDO1 66 35 IRQ4, P24
P72, A10, SDO2 67 34 IRQ3, P23
P73, A11, SDO3 68 33 IRQ2, P22
P74, A12, SDO4 69 32 ACZ, IRQ1, P21
P75, A13, SDO5 70 31 IRQ0, P20
P76, SDO6 71 30 TCIO7, P14
P77, SDO7 72 29 TCIO3, P13
P87, LED7, D7 73 28 TCIO2, P12
P86, LED6, D6 74 27 TCIO1, P11
P85, LED5, D5 75 26 RMOUT, TCIO0, P10
P84, LED4, D4 76 25 NRST, P27
P83, LED3, D3 77 24 NDK, BUZZER, P06
P82, LED2, D2 78 23 SBT2, P05
P81, LED1, D1 79 22 SBI2, P04
P80, LED0, D0 80 21 SBO2, P03
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9
VREF-

OUTC
N.C.
VREF+
VDD
OSC2
OSC1
VSS
XI
XO
MMOD
TXD1, SBO1, P00
RXD1, SBI1, P01
SBT1, P02
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5

Note) Pin 9 serves as the VPP pin in the MN101CF61G, and cannot be used as a user pin.

MAD00009KEM 23
 MN101C62 Series
Type MN101C62D MN101C62F MN101CF62G
Internal ROM type Mask ROM FLASH
ROM (byte) 64K 96K 128K
RAM (byte) 2K 4K 10K
Package (Lead-free) LQFP080-P-1414A
[Standard]
0.10 µs (at 4.5 V to 5.5 V, 20 MHz)
0.25 µs (at 2.7 V to 5.5 V, 8 MHz)
1.00 µs (at 2.0 V to 5.5 V, 2 MHz)*
Minimum Instruction 125 µs (at 2.0 V to 5.5 V, 32 kHz)*
Execution Time [Double speed]
0.125 µs (at 4.5 V to 5.5 V, 8 MHz)
0.25 µs (at 3.0 V to 5.5 V, 4 MHz)
62.5 µs (at 2.0 V to 5.5 V, 32 kHz)*
*: The lower limit for operation guarantee for flash memory built-in type is 2.5 V.

 Interrupts
Watchdog. External 0 to 4. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Time base. Automatic transfer finish. Serial 0
(2 systems). Serial 1 (2 systems). Serial 2. A/D conversion finish. Key interrupt

 Timer Counter
8-bit timer × 6
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement
Timer 1 ..................Square-wave output. Event count. Synchronous output event. Serial baud rate timer
Timer 2 ..................Square-wave output. Event count. Synchronous output event. Simple pulse width measurement. Real time output
control. Serial baud rate timer
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial baud rate timer
Timer 4 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output
event. Pulse width measurement. Input capture. Real time output control
Timer 8 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output
event. Pulse width measurement. Input capture. Real time output control
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Single-master I2C × 1: Serial 2

 I/O Pins
I/O 68 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 8 channels (with S/H)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 3 addresses possible

24 MAD00020LEM
 MN101C62D, MN101C62F, MN101CF62G

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 15(20) 30(40) mA
Operating supply current
IDD2 fx = 32 kHz. VDD = 3 V 30(50) 60(100) µA
Supply current at HALT IDD3 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 6 8 µA
Supply current at HALT IDD4 fx = 32 kHz. VDD = 3 V. Ta = 85 °C 30 µA
IDD5 VDD = 5 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD6 VDD = 5 V. Ta = 85 °C 50 µA
Note) ( ): Flash memory built-in type

 Pin Assignment
LQFP080-P-1414A

P35, SBT0B
P47, KEY7
P46, KEY6
P45, KEY5
P44, KEY4
P43, KEY3
P42, KEY2
P41, KEY1
P40, KEY0
P50, NWE
P51, NRE
P52, NCS
P63, A03
P62, A02
P61, A01
P60, A00

P54, A17

P53, A16
VDD2

VSS2
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
P64, A04 61 40 TM8I0, RXD0B, SBI0B, P34
P65, A05 62 39 TM4I0, TXD0B, SB00B, P33
P66, A06 63 38 SCL, SBT2, P32
P67, A07 64 37 SBI2, P31
P70, SD00, A08 65 36 SDA, SB02, P30
P71, SD01, A09 66 35 IRQ4, P24
P72, SD02, A10 67 34 IRQ3, P23
P73, SD03, A11 68 33 IRQ2, P22
P74, SD04, A12 69 32 ACZ, IRQ1, P21
P75, SD05, A13 70 31 IRQ0, P20
P76, SD06, A14 71 30 TM7I0, P14
P77, SD07, A15 72 29 TM3I0, P13
P87, LED7, D7 73 28 TM2I0, P12
P86, LED6, D6 74 27 TM1I0, P11
P85, LED5, D5 75 26 RMOUT, TMOI0, P10
P84, LED4, D4 76 25 NDK, BUZZER, P06
P83, LED3, D3 77 24 SBT1, P05
P82, LED2, D2 78 23 RXD1, SBI1, P04
P81, LED1, D1 79 22 TXD1, SB01, P03
P80, LED0, D0 80 21 SBT0A, P02
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9
VSS3

VDD1

VSS1
VREF+

OSC2
OSC1

XI
X0
MM0D

TXD0A, SB00A, P00

RXD0A, SBI0A, P01
NRST, P27
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6
AN7, PA7

MAD00020LEM 25
 MN101C67 Series
Type MN101C67D MN101C67G MN101CF67G
Internal ROM type Mask ROM FLASH
ROM (byte) 64K 128K
RAM (byte) 6K 10K
Package (Lead-free) TQFP080-P-1212D
[Standard]
0.1 µs (at 2.5 V to 3.6 V, 20 MHz)*
0.2 µs (at 2.1 V to 3.6 V, 10 MHz)*
Minimum Instruction 0.5 µs (at 1.8 V to 3.6 V, 4 MHz)*
Execution Time 62.5 µs (at 1.8 V to 3.6 V, 32 kHz)*
[Double speed]
0.119 µs (at 2.5 V to 3.6 V, 8.39 MHz)*
* The operation guarantee range for flash memory built-in type is 2.7 V to 3.6 V.

 Interrupts
RESET. Watchdog. External 0 to 5. Timer 0 to 6. Timer 7 (2 systems). Time base. Serial 0 reception. Serial 0 transmission. Serial 1
reception. Serial 1 transmission. Serial 2 to 4. Automatic transfer finish. A/D conversion finish. Key interrupts (8 lines)

 Timer Counter
8-bit timer × 7
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Pulse width measurement
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event. Pulse width measurement
Timer 3 ..................Square-wave output. Event count. Remote control carrier output
Timer 4 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial 1 baud rate timer
Timer 5 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial 0 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
width measurement. Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type × 1: Serial 2
Synchronous type/Single-master I2C × 1: Serial 3
I2C slave × 1: Serial 4
Serial 4...................I2C high-speed transfer mode. 7-bit/10-bit address setting. General call

 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 62 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
Input 7 : Common use. Specified pull-up resistor available

 A/D converter
10-bit × 7 channels (with S/H)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 3 addresses possible

26 MAD00036LEM
 MN101C67D, MN101C67G, MN101CF67G

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz (fs = fosc/2). VDD = 3 V 5 12 mA
Operating supply current IDD2 fosc = 8.39 MHz (fs = fosc/2). VDD = 3 V 2 5 mA
IDD3 fx = 32.768 kHz (fs = fx/2). VDD = 3 V 40 µA
IDD4 fx = 32.768 kHz. VDD = 3 V. Ta = 25 °C 4 8 µA
Supply current at HALT
IDD5 fx = 32.768 kHz. VDD = 3 V 30 µA
IDD6 VDD = 3 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD7 VDD = 3 V. Ta = 85 °C 30 µA
Ta = -40 °C to +85 °C. VDD = 1.8 V to 3.6 V. VSS = 0 V

 Pin Assignment
TQFP080-P-1212D

P40, TXD0, SBO0, KEY0

P41, RXD0, SBI0, KEY1

P37, TCIO4, NDKDMA

P43, TCIO5, KEY3
P42, SBT0, KEY2
P47, KEY7, A15
P46, KEY6, A14
P52, IRQ5, NCS

P45, KEY5, A9
P44, KEY4, A8
P50, NWE
P51, NRE

P36, SDA
P35, SCL
P54, A17
P53, A16
P63, A3
P62, A2
P61, A1
P60, A0
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
P64, A4 61 41 40 P34
P65, A5 62 39 P33
P66, A6 63 38 P32
P67, A7 64 37 SYSCLK, SBI3, P31
P70, SDO0 65 36 SBO3, P30
P71, SDO1 66 35 IRQ4, P24
P72, A10, SDO2 67 34 IRQ3, P23
P73, A11, SDO3 68 33 IRQ2, P22
P74, A12, SDO4 69 32 ACZ, IRQ1, P21
P75, A13, SDO5 70 31 IRQ0, P20
P76, SDO6 71 30 TCIO7, P14
P77, SDO7 72 29 TCIO3, P13
P87, LED7, D7 73 28 TCIO2, P12
P86, LED6, D6 74 27 TCIO1, P11
P85, LED5, D5 75 26 RMOUT, TCIO0, P10
P84, LED4, D4 76 25 NRST, P27
P83, LED3, D3 77 24 NDK, BUZZER, P06
P82, LED2, D2 78 23 SBT2, P05
P81, LED1, D1 79 22 SBI2, P04
P80, LED0, D0 80 21 SBO2, P03
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9
VREF-

OUTC
NC
VREF+
VDD
OSC2
OSC1
VSS
XI
XO
MMOD
TXD1, SBO1, P00
SDA, RXD1, SBI1, P01
SCL, SBT1, P02
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5

Note) Pin 9 serves as the VPP pin in the MN101CF67G, and cannot be used as a user pin.

MAD00036LEM 27
 MN101C91 Series
Type MN101CF91D
Internal ROM type FLASH
ROM (byte) 64K
RAM (byte) 4K
Package (Lead-free) TQFP048-P-0707B
Minimum Instruction 0.1 µs (at 2.7 V to 3.6 V, 10 MHz)
Execution Time 62.5 µs (at 2.7 V to 3.6 V, 32 kHz)

 Interrupts
RESET. Watchdog. External 0 to 5. External 6 (key interrupt dedicated). Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems).
Time base. Serial 0 (2 systems). Serial 1 (2 systems). Serial 2 (3 systems). A/D conversion finish

 Timer Counter
8-bit timer × 6
Timer 0 ..................Square-wave output. PWM output. Event count. Simple pulse width measurement. Square-wave/PWM output to
large current terminal P50 (TM0OA) or P30 (TM0OB) possible
Timer 1 ..................Square-wave output. Event count. UART baud rate timer
Timer 2 ..................Square-wave output. PWM output. Event count. Simple pulse width measurement. UART baud rate timer.
Square-wave/PWM output to large current terminal P52 (TM2OA) or P32 (TM2OB) possible
Timer 3 ..................Square-wave output. Event count
Timer 4 ..................Square-wave output. PWM output. Event count. Simple pulse width measurement
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. PWM output (cycle/duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P51 (TM7O) possible
Timer 8 ..................Square-wave output. PWM output (cycle/duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P53 (TM8O) possible
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Multi-master I2C × 1: Serial 2
Serial 2...................7-bit/10-bit address setting. General call. SMBus

 Extended Calculation
16-bit × 16-bit multiplication. 32-bit / 16-bit division

 I/O Pins
I/O 37 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 6 channels (with S/H)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port. Clock output

 ROM Correction
Correcting address designation: Up to 3 addresses possible

28 MAD00055FEM
 MN101CF91D

 Pin Assignment
TQFP048-P-0707B

P35, KEY5, NBUZZER

P36, KEY6, CLKOUT

P34, KEY4, BUZZER

P32, KEY2, TM2OB

P30, KEY0, TM0OB

P33, KEY3, TM3IO

P31, KEY1, TM1IO

P23, IRQ3
P22, IRQ2
P21, IRQ1
P20, IRQ0
DMOD
36
35
34
33
32
31
30
29
28
27
26
25
P40, RXD0B, SBI0B 37 24 SCL2, SBT2, P16
P41, TXD0B, SBO0B 38 23 SDA2, SBO2, P15
P42, SBT0B 39 22 TM4IO, SBI2, P14
P43, RXD1B, SBI1B 40 21 TM8IO, P13
P44, TXD1B, SBO1B 41 20 TM7IO, P12
P45, SBT1B 42 19 TM2IO, P11
P50, LED0, TM0OA 43 18 RMOUT, TM0IO, P10
P51, LED1, TM7O 44 17 SBT1A, AN5, P05
P52, LED2, TM2OA 45 16 TXD1A, SBO1A, AN4, P04
P53, LED3, TM8O 46 15 RXD1A, SBI1A, AN3, P03
P54, LED4, IRQ4 47 14 SBT0A, AN2, P02
P55, LED5, IRQ5 48 13 TXD0A, SBO0A, AN1, P01

10

12
11
1
2
3
4
5
6
7
8
9
VSS
OSC2
OSC1
XI
XO
MMOD

VDD18
VDD33
OSCMOD
VREF+
RXD0A, SBI0A, AN0, P00
NRST, P27

MAD00055FEM 29
 MN101C94 Series
Type MN101C94A MN101CF94D
Internal ROM type Mask ROM FLASH
ROM (byte) 32K 64K
RAM (byte) 1K 2K
Package (Lead-free) QFP044-P-1010F
0.10 µs (at 4.5 V to 5.5 V, 20 MHz)
Minimum Instruction 0.238 µs (at 2.7 V to 5.5 V, 8.39 MHz)
Execution Time 0.477 µs (at 2.0 V to 5.5 V, 4.19 MHz)*
*: The lower limit for operation guarantee for flash memory built-in type is 2.5 V.

 Interrupts
RESET. Watchdog. External 0 to 2. Timer 0 to 5. Time base. Serial 0. A/D conversion finish

 Timer Counter
8-bit timer × 4
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Synchronous output event
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 4 ..................Square-wave/16-bit PWM output. Event count. Synchronous output event. Input capture
Time base timer: One-minute count setting. Independently operable 8-bit timer 5
Watchdog timer × 1

 Serial interface
Synchronous type/Simple UART (half-duplex) × 1: Serial 0

 I/O Pins
I/O 26 : Common use: 17. Specified pull-up resistor available
Input/output selectable (bit unit): 26
Input 11 : Common use. Specified pull-up resistor available

 A/D converter
10-bit × 8 channels (with S/H)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 15 40 mA
Operating supply current
IDD2 fosc = 8.39 MHz. VDD = 5 V 6 18 mA
Supply current at HALT IDD3 fosc = 8.39 MHz. VDD = 5 V. Ta = 25 °C 1.2 3 mA
IDD4 VDD = 5 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD5 VDD = 5 V. Ta = -40 °C to +85 °C 20(50) µA
Note) ( ): Flash memory built-in type

30 MAD00052FEM
 MN101C94A, MN101CF94D

 Pin Assignment
QFP044-P-1010F

P14, TMIO4
P13, TMIO3
P12, TMIO2
P22, IRQ2
P21, IRQ1
P20, IRQ0
P63
P62
P61
P60

P11
33
32
31
30
29
28
27
26
25
24
23
P64 34 22 P10, RMOUT
P65 35 21 P06, BUZZER
P66 36 20 P02, SBT0
P67 37 19 P01, SBI0, RXD
P70 38 18 P00, SBO0, TXD
NRST, P27 39 17 N.C.
MMOD 40 16 VSS
LED7, P87 41 15 OSC1
LED6, P86 42 14 OSC2
LED5, P85 43 13 VDD
LED4, P84 44 12 PA7, AN7

10
11
1
2
3
4
5
6
7
8
9
LED3, P83
LED2, P82
LED1, P81
LED0, P80
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6

MAD00052FEM 31
 MN101C95 Series
Type MN101CF95G
Internal ROM type FLASH
ROM (byte) 128K
RAM (byte) 6K
Package (Lead-free) TQFP080-P-1212D
[Standard]
0.2 µs (at 2.7 V to 3.6 V, 10 MHz)
Minimum Instruction 0.5 µs (at 2.7 V to 3.6 V, 4 MHz)
Execution Time 62.5 µs (at 2.7 V to 3.6 V, 32 kHz)
[Double speed]
0.1 µs (at 2.7 V to 3.6 V, 10 MHz)

 Interrupts
RESET. Watchdog. External 0 to 5. Timer 0 to 8. Time base. Serial 0 reception. Serial 0 transmission. Serial 1 reception. Serial 1
transmission. Serial 2. Serial 3. Serial 4 reception. Serial 4 transmission. Automatic transfer finish. A/D conversion finish. Key interrupts
(12 lines)

 Timer Counter
8-bit timer × 7
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial transfer clock output. Real time
output control. Remote control carrier output
Timer 1 ..................Square-wave output. Event count. Synchronous output event. Serial transfer clock output
Timer 2 ..................Square-wave output. PWM output. Event count. Pulse width measurement. Timer synchronous output. Serial
transfer clock output
Timer 3 ..................Square-wave output. Event count. Serial transfer clock output
Timer 4 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Real time output control. Serial transfer
clock output
Timer 5 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial transfer clock output
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 0, 1, 2 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 0, 1, 2, 3 can be cascade-connected
Timer 4, 5 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
width measurement. Input capture. Real time output control
Timer 8 ..................Square-wave output. PWM output (duty continuous variable). Event count. Pulse width measurement. Input
capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 3: Serial 0, 1, 4
Synchronous type/Multi-master I2C × 1: Serial 2
Synchronous type/Single-master I2C × 1: Serial 3

 DMA controller
Maximum transfer cycles: 255
Starting factor: Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 67 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 11 channels (with S/H)

 Extended Calculation
16-bit × 16-bit multiplication. 32-bit / 16-bit division

32 MAD00053GEM
 MN101CF95G

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 Pin Assignment
TQFP080-P-1212D

P54, TM1IO, TM0OB, RMOUTB

P70, SDO0, SBO1B, TXD1B
P71, SDO1, SBI1B, RXD1B

P53, TM0IOA, RMOUTA

P74, SDO4, TM7OB
P75, SDO5, TM8IO

P72, SDO2, SBT1B

P42, KEY10
P43, KEY11

P41, KEY9
P40, KEY8
P67, KEY7
P66, KEY6
P65, KEY5
P64, KEY4
P63, KEY3
P62, KEY2
P61, KEY1
P60, KEY0
P73, SDO3
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
TM4IO, SDO6, P76 61 40 P25, IRQ5, TM7IOA
TM5IO, SDO7, P77 62 39 P24, IRQ4
LED7, P87 63 38 P23, IRQ3
LED6, P86 64 37 P22, IRQ2
SBT0A, LED5, P85 65 36 P21, IRQ1
RXD0A, SBI0A, LED4, P84 66 35 P20, IRQ0
TXD0A, SBO0A, LED3, P83 67 34 P36
LED2, P82 68 33 P35, SBT4
LED1, P81 69 32 P34, SBI4, RXD4
LED0, P80 70 31 P33, SBO4, TXD4
KEY12, P44 71 30 P32, TM3IO
KEY13, P45 72 29 P31, TM2OB
KEY14, P46 73 28 P30, TM2IOA
KEY15, P47 74 27 P15, SBT2, SCL2, SBT0B
VREF- 75 26 P14, SBI2, SBI0B, RXD0B
AN0, PA0 76 25 P13, SBO2, SDA2, SBO0B, TXD0B
AN1, PA1 77 24 P12, SBT1A
AN2, PA2 78 23 P11, SBI1A, RXD1A
AN3, PA3 79 22 P10, SBO1A, TXD1A
AN4, PA4 80 21 P02, SBT3, SCL3, BUZZER
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9
AN7, PB0
AN8, PB1
AN9, PB2
AN10, PB3
DMOD
VREF+
VPP
VDD33
VDD18
OSC2
OSC1
VSS
XI
XO
MMOD
P27, NRST
SDA3, SBO3, P00
SBI3, P01
AN5, PA5
AN6, PA6

MAD00053GEM 33
 MN101C97 Series
Type MN101C97A MN101C97D MN101CF97D
Internal ROM type Mask ROM FLASH
ROM (byte) 32K 64K
RAM (byte) 1K
Package (Lead-free) QFP044-P-1010F (ES (Engineering Sample) available), TQFP048-P-0707B
0.25 µs (at 2.2 V to 3.6 V, 8 MHz)
Minimum Instruction 0.5 µs (at 1.8 V to 3.6 V, 4 MHz)
Execution Time 62.5 µs (at 1.8 V to 3.6 V, 32 kHz)

 Interrupts
RESET. Watchdog. External 0 to 5. External 6 (key interrupt dedicated). Timer 0 to 3. Timer 6. Timer 7 (2 systems). Time base. Serial 0 (2
systems). Serial 3. A/D conversion finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Added pulse (2-bit) type PWM output. Square-wave/PWM output to large current terminal P51 possible
Timer 1 ..................Square-wave output. Event count. Synchronous output event. Serial 0 baud rate timer
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. PWM output. Serial transfer clock output. Event
count. Synchronous output event. Simple pulse width measurement. Serial 0 and Serial 3 baud rate timer. Square-
wave/PWM output to large current terminal P52 possible
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 3 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output
event. Pulse width measurement. Input capture. Square-wave/PWM output to large current terminal P53 possible
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0
Synchronous type/Single-master I2C × 1: Serial 3

 I/O Pins
I/O 38 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 8 channels (with S/H)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 3 addresses possible

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 4 MHz. VDD = 3 V 0.9 1.7 mA
Operating supply current
IDD2 fx = 32 kHz. VDD = 3 V 4 24 µA
IDD3 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 2.6 5 µA
Supply current at HALT
IDD4 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 20 µA
IDD5 VDD = 3 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD6 VDD = 3 V. Ta = -40 °C to +85 °C 15 µA
Note) Limit: Mask ROM version

34 MAD00058GEM
 MN101C97A, MN101C97D, MN101CF97D

 Pin Assignment
TQFP048-P-0707B

P11, TXD0A, SBO0A

P25, IRQ5, CLKOUT

P10, RXD0A, SBI0A

P31, KEY1, TM1IO
P30, KEY0, TM0IO

P12, SBT0A
P24, IRQ4
P23, IRQ3
P22, IRQ2
P21, IRQ1
P20, IRQ0
P13
36
35
34
33
32
31
30
29
28
27
26
25
P32, KEY2, TM2IO 37 24 AN7, P07
P33, KEY3, TM3IO 38 23 AN6, P06
P34, KEY4, TM7IO 39 22 AN5, P05
P35, KEY5, NBUZZER 40 21 AN4, P04
P36, KEY6, BUZZER 41 20 AN3, P03
P37, KEY7 42 19 AN2, P02
P40, SBI3 43 18 AN1, P01
P41, SBO3, SDA3 44 17 AN0, P00
P42, SBT3, SCL3 45 16 VREF+
P43, RXD0B, SBI0B 46 15 LED4, P54
P44, TXD0B, SBO0B 47 14 TM7O, LED3, P53
P45, SBT0B 48 13 TM2O, LED2, P52

10

12
11
1
2
3
4
5
6
7
8
9
DMOD
VDD

XO
XI
MMOD
OSC1
OSC2
VSS
LED5, P55

TM0O, LED1, P51

NRST, P27

RMOUT, LED0, P50

QFP044-P-1010F
P11, TXD0A, SBO0A
P25, IRQ5, CLKOUT

P10, RXD0A, SBI0A

P31, KEY1, TM1IO
P30, KEY0, TM0IO

P12, SBT0A
P24, IRQ4
P23, IRQ3
P22, IRQ2
P21, IRQ1
P20, IRQ0
33
32
31
30
29
28
27
26
25
24
23

P32, KEY2, TM2IO 34 22 AN7, P07

P33, KEY3, TM3IO 35 21 AN6, P06
P34, KEY4, TM7IO 36 20 AN5, P05
P35, KEY5, NBUZZER 37 19 AN4, P04
P36, KEY6, BUZZER 38 18 AN3, P03
P40, SBI3 39 17 AN2, P02
P41, SBO3, SDA3 40 16 AN1, P01
P42, SBT3, SCL3 41 15 AN0, P00
P43, RXD0B, SBI0B 42 14 VREF+
P44, TXD0B, SBO0B 43 13 TM7O, LED3, P53
P45, SBT0B 44 12 TM2O, LED2, P52
10
11
1
2
3
4
5
6
7
8
9
DMOD
VDD

XO
XI
MMOD
OSC1
OSC2
VSS

TM0O, LED1, P51

NRST, P27

RMOUT, LED0, P50

MAD00058GEM 35
 MN101CA7 Series
Type MN101CA7A MN101CFA7D
Internal ROM type Mask ROM FLASH
ROM (byte) 32K 64K
RAM (byte) 2K
Package (Lead-free) TQFP048-P-0707B TQFP048-P-0707B (Under planning)
0.10 µs (at 2.7 V to 3.6 V, 10 MHz)
Minimum Instruction 0.25 µs (at 1.8 V to 3.6 V, 8 MHz)
Execution Time 62.5 µs (at 1.8 V to 3.6 V, 32 kHz)

 Interrupts
RESET. Watchdog. External 0 to 5. External 6 (key interrupt dedicated). Timer 0 to 3. Timer 6. Timer 7 (2 systems). Time base. Serial 0 (2
systems). Serial 3. Serial 4. A/D conversion finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Added pulse (2-bit) type PWM output. Square-wave/PWM output to large current terminal P51 possible
Timer 1 ..................Square-wave output. Event count. Synchronous output event. Serial 0 baud rate timer
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. PWM output. Serial transfer clock output. Event
count. Synchronous output event. Simple pulse width measurement. Serial 0 and Serial 3 baud rate timer. Square-
wave/PWM output to large current terminal P52 possible
Timer 3 ..................Square-wave output. Event count. Serial 3 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output
event. Pulse width measurement. Input capture. Real time output control. Square-wave/PWM output to large
current terminal P53 possible
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0
Synchronous type/Single-master I2C × 1: Serial 3
I2C slave × 1: Serial 4
Serial 4...................I2C high-speed transfer mode. 7-bit/10-bit address setting. General call

 I/O Pins
I/O 35 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 8 channels (with S/H)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 3 addresses possible

 Reference Power Supply Output

1.8 V: Output to ADREF terminal possible

 Internal oscillation
High speed: 8 MHz

36 MAD00071CEM
 MN101CA7A, MN101CFA7D

 Pin Assignment
TQFP048-P-0707B

P11, TXD0A, SBO0A

P25, IRQ5, CLKOUT

P10, RXD0A, SBI0A

P31, KEY1, TM1IO
P30, KEY0, TM0IO

P12, SBT0A
P24, IRQ4
P23, IRQ3
P22, IRQ2
P21, IRQ1
P20, IRQ0
ATRSEL
36
35
34
33
32
31
30
29
28
27
26
25
P32, KEY2, TM2IO 37 24 SCL4, AN7, P07
P33, KEY3, TM3IO 38 23 SDA4, AN6, P06
P34, KEY4, TM7IO 39 22 AN5, P05
P35, KEY5, NBUZZER 40 21 AN4, P04
P36, KEY6, BUZZER 41 20 AN3, P03
DMOD 42 19 AN2, P02
P40, SBI3 43 18 AN1, P01
P41, SBO3, SDA3 44 17 AN0, P00
P42, SBT3, SCL3 45 16 Vref+
P43, RXD0B, SBI0B 46 15 ADREF
P44, TXD0B, SBO0B 47 14 TM7O, LED3, P53
P45, SBT0B 48 13 TM2O, LED2, P52

10

12
11
1
2
3
4
5
6
7
8
9
VDD18
VDD33

XO
XI
MMOD
OSC1
OSC2
VSS
LED5, P55

TM0O, LED1, P51

NRST, P27

RMOUT, LED0, P50

MAD00071CEM 37
 MN101CB6 Series
Type MN101CB6A MN101CB6D MN101CB6G MN101CFB6G
Internal ROM type Mask ROM FLASH
ROM (byte) 32K 64K 124K 128K
RAM (byte) 1K 2K
SSOP032-P-0300B
Package (Lead-free) SSOP032-P-0300B (Under development)
0.10 µs (at 2.7 V to 3.6 V, 10 MHz)
Minimum Instruction 0.125 µs (at 1.8 V to 3.6 V, 8 MHz)
Execution Time 100 µs (at 1.8 V to 3.6 V, 20 kHz)

 Interrupts
RESET. Watchdog. External 0 to 4. Timer 0 to 3. Timer 7 (2 systems). Serial 0 (2 systems). A/D conversion finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Simple pulse width measurement. Added pulse (2-bit) type PWM
output. Square-wave/PWM output to large current terminal P35 possible
Timer 1 ..................Serial 0 baud rate timer
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. PWM output. Event count. Simple pulse width
measurement. Serial 0 baud rate timer. Square-wave/PWM output to large current terminal P34 possible
Timer 3 ..................Interval timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Pulse width measurement.
Input capture. Square-wave/PWM output to large current terminal P33 possible
Time base timer: One-minute count setting
Watchdog timer × 1
Watchdog timer 2 × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0

 I/O Pins
I/O 17 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 5 channels (with S/H)

 Special Ports
High-current drive port

 ROM Correction
Correcting address designation: Up to 3 addresses possible

 Gain Amplifier
2 channels

 Reference Power Supply Output

1.7 V: Output to REF17 terminal possible. Supply to A/D converter input, A/D converter reference voltage and a reference power for
Double Booster Circuit possible

 Double Booster Circuit

Counle boosts REF17 terminal input voltage or Reference Power Supply Output

 Reset
Automatic Reset

 Internal oscillation
High speed: 8 MHz. Low speed: 20 kHz

38 MAD00077BEM
MAD00077BEM
 Pin Assignment
SSOP032-P-0300B

P33, LED3, TM7O 1 32 VDPUMP

P32, LED2 2 31 P34, LED4, TM2IO, C1
P31, LED1 3 30 P35, LED5, IRQ4, TM0IO, C2
P30, LED0 4 29 REF17, AN4
VSS 5 28 P03, AN3
OSC1, P24 6 27 P02, AN2
OSC2, P25 7 26 P01, AN1
MMOD 8 25 P00, AN0
NRST, P27 9 24 AVDD
VDD18 10 23 ANOUT1
VDD33 11 22 ANIN1N
DMOD 12 21 ANIN1P
P20, IRQ0, SBT0A 13 20 ANOUT0
P21, IRQ1, SBO0A, TXD0A 14 19 ANIN0N
P22, IRQ2, SBI0A, RXD0A 15 18 ANIN0P
P23, IRQ3, TM7IO, CLKOUT 16 17 P10, VDAMP
MN101CB6A, MN101CB6D, MN101CB6G, MN101CFB6G

39
 MN101CD0 Series
Type MN101CD0A MN101CD0D MN101CD0G MN101CFD0G
Internal ROM type Mask ROM FLASH
ROM (byte) 32K 64K 124K 128K
RAM (byte) 1K 2K
SSOP032-P-0300B
Package (Lead-free) SSOP032-P-0300B (Under development)
0.10 µs (at 2.7 V to 3.6 V, 10 MHz)
Minimum Instruction 0.125 µs (at 1.8 V to 3.6 V, 8 MHz)
Execution Time 100 µs (at 1.8 V to 3.6 V, 20 kHz)

 Interrupts
RESET. Watchdog. External 0 to 4. External 6 (key interrupt dedicated). Timer 0 to 3. Timer 6. Timer 7 (2 systems). Time base. Serial 0 (2
systems). A/D conversion finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Simple pulse width measurement. Added pulse (2-bit) type PWM
output. Square-wave/PWM output to large current terminal P35 possible
Timer 1 ..................Serial 0 baud rate timer
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. PWM output. Event count. Simple pulse width
measurement. Serial 0 baud rate timer. Square-wave/PWM output to large current terminal P34 possible
Timer 3 ..................Interval timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Pulse width measurement.
Input capture. Square-wave/PWM output to large current terminal P33 possible
Time base timer: One-minute count setting
Watchdog timer × 1
Watchdog timer 2 × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0

 I/O Pins
I/O 23 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 5 channels (with S/H)

 Special Ports
High-current drive port

 ROM Correction
Correcting address designation: Up to 3 addresses possible

 Gain Amplifier
2 channels

 Reference Power Supply Output

1.7 V: Output to REF17 terminal possible. Supply to A/D converter input, A/D converter reference voltage possible

 Reset
Automatic Reset

 Internal oscillation
High speed: 8 MHz. Low speed: 20 kHz

40 MAD00073CEM
MAD00073CEM
 Pin Assignment
SSOP032-P-0300B

P33, LED3, TM7O 1 32 VDD33

P32, LED2 2 31 P34, LED4, TM2IO
P31, LED1 3 30 P35, LED5, IRQ4, TM0IO
P30, LED0 4 29 REF17, AN4
VSS 5 28 P03, AN3
OSC1, P24 6 27 P02, AN2
OSC2, P25 7 26 P01, AN1
MMOD 8 25 P00, AN0
NRST, P27 9 24 TMOD
VDD18 10 23 P16, KEY6, ANOUT1
VDD33 11 22 P15, KEY5, ANIN1N
DMOD 12 21 P14, KEY4, ANIN1P
P20, IRQ0, SBT0A 13 20 P13, KEY3, ANOUT0, SBI0B, RXD0B
P21, IRQ1, SBO0A, TXD0A 14 19 P12, KEY2, ANIN0N, SBO0B, TXD0B
P22, IRQ2, SBI0A, RXD0A 15 18 P11, KEY1, ANIN0P, SBT0B
P23, IRQ3, TM7IO, CLKOUT 16 17 P10, KEY0, VDAMP
MN101CD0A, MN101CD0D, MN101CD0G, MN101CFD0G

41
 MN101E16 Series
Type MN101E16K MN101E16Y MN101EF16K MN101EF16Z
Internal ROM type Mask ROM FLASH
ROM (byte) 256K 384K 260K 512K
RAM (byte) 12K 20K 16K 30K
LQFP100-P-1414, LQFP100-P-1414,
Package (Lead-free) QFP100-P-1818B QFP100-P-1818B
QFP100-P-1818B QFP100-P-1818B
0.0588 µs (at 2.7 V to 3.6 V, 17 MHz, at internal 2, 4, 8 times oscillation))
Minimum Instruction 0.1 µs (at 2.7 V to 3.6 V, 20 MHz)
Execution Time 30.6 µs (at 2.7 V to 3.6 V, 32.768 kHz)

 Interrupts
RESET. Watchdog. External 0 to 5. Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer A to E.Time base. Serial 0 (2 systems). Serial 1 (2
systems). Serial 2. Serial 3 (2 systems). Serial 4 (2 systems). Automatic transfer finish (2 systems). A/D conversion finish. Key interrupt

 Timer Counter
8-bit timer × 10
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Real time output control
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event. Pulse width measurement. Real time
output control. Serial baud rate timer
Timer 3 ..................Square-wave output. Event count. Serial baud rate timer
Timer 6 ..................8-bit freerun timer. Time base timer
Timer A, B, C, D, E
Timer 0, 1 can be cascade-connected
Timer 0, 1, 2 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 0, 1, 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
width measurement. Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 3: Serial 0, 1, 4
Synchronous type/Single-master I2C × 1: Serial 2
Synchronous type/I2C × 1: Serial 3

 DMA controller
Number of channels: 2 channels
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 22 : (5 V I/F port) Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
62 : (3 V I/F port) Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
1 : (3 V I/F port) Common use

 A/D converter
10-bit × 8 channels (with S/H)

 Special Ports
Buzzer output. High-current drive port

 ROM Correction
Correcting address designation: Up to 7 addresses possible

42 MAD00046LEM
 MN101E16K, MN101E16Y, MN101EF16K, MN101EF16Z

 Pin Assignment
LQFP100-P-1414, QFP100-P-1818B

P40, SBO4, TXD4

P41, SBI4, RXD4

P67, KEY7, A15

P66, KEY6, A14
P65, KEY5, A13
P64, KEY4, A12
P76, SD6, NWE
P77, SD7, NDK

P75, SD5, NRE

P74, SD4, NCS
P87, LED7, D7
P86, LED6, D6
P85, LED5, D5
P84, LED4, D4
P83, LED3, D3
P82, LED2, D2
P81, LED1, D1
P80, LED0, D0

P73, SD3, A19

P72, SD2, A18
P71, SD1, A17
P70, SD0, A16
P42, SBT4

VSS
P43
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
SBO0B, TXD0B, P90 76 50 P63, KEY3, A11
SBI0B, RXD0B, P91 77 49 P62, KEY2, A10
SBT0B, P92 78 48 P61, KEY1, A9
SBO3B, SDA3B, P93 79 47 P60, KEY0, A8
SBI3B, P94 80 46 P57, A7
SBT3B, SCL3B, P95 81 45 P56, A6
SBO2B, SDA2B, PD0 82 44 P55, A5
SBI2B, PD1 83 43 P54, A4
SBT2B, SCL2B, PD2 84 42 P53, A3
IRQ0B, PD3 85 41 P52, A2
IRQ1B, PD4 86 40 P51, A1
IRQ2B, PD5 87 39 VSS
IRQ3B, PD6 88 38 P50, A0
VDD5 89 37 VDD18
PD7 90 36 P35, SBT3A, SCL3A
VSS 91 35 P34, SBI3A
AN0, PA0 92 34 P33, SBO3A, SDA3A
AN1, PA1 93 33 P32, SBT1
AN2, PA2 94 32 P31, SBI1, RXD1
AN3, PA3 95 31 P30, SBO1, TXD1
AN4, PA4 96 30 P25, IRQ5
AN5, PA5 97 29 P24, IRQ4
AN6, PA6 98 28 P23, IRQ3A
AN7, PA7 99 27 P22, IRQ2A
VREF+ 100 26 P21, IRQ1A
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
SBO0A, TXD0A, P00
SBI0A, RXD0A, P01
SBT0A, P02
SBO2A, SDA2A, P03
SBI2A, P04
SBT2A, SCL2A, P05
BUZZER, P06
TM0IO, P10

TM2IO, P12
MMOD
OSC2
OSC1
VSS
XI
XO
VDD33
VDD18

TM3IO, P13
TM7IOA, P14
TM7OB, P15
TM7OC, P16
SYSCLK, P17
IRQ0A, P20
TM1IO, P11

NRST, P27

MAD00046LEM 43
 MN101E34 Series
Type MN101EF34D
Internal ROM type FLASH
ROM (byte) 64K+4K
RAM (byte) 4K
Package (Lead-free) TQFP048-P-0707B
Minimum Instruction 0.042 µs (at 2.2 V to 5.5 V, 24 MHz)
Execution Time 62.5 µs (at 2.2 V to 5.5 V, 32 kHz)

 Interrupts
RESET. Watchdog. External 0 to 4. External 5 (key interrupt dedicated). External 6. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2
systems). Timer 9 (2 systems). Time base. Serial 1 (2 systems). Serial 2 (2 systems). Serial 4 (2 systems). A/D conversion finish

 Timer Counter
8-bit timer × 6
Timer 0 ..................Square-wave output. PWM output. Event count. Simple pulse width measurement. Square-wave/PWM output to
large current terminal P03 (TM0IOB) possible
Timer 1 ..................Square-wave output. Event count
Timer 2 ..................Square-wave output. PWM output. Event count. Simple pulse width measurement. Square-wave/PWM output to
large current terminal P03 (TM2IOB) possible
Timer 3 ..................Square-wave output. Event count
Timer 4 ..................Square-wave output. PWM output. Event count. Simple pulse width measurement. Square-wave/PWM output to
large current terminal P02 (TM4IOC) possible
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 0, 1, 2 can be cascade-connected
Timer 0, 1, 2, 3 can be cascade-connected
16-bit timer × 3
Timer 7 ..................Square-wave output. PWM output (cycle/duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P00 (TM7IOB) possible
Timer 8 ..................Square-wave output. PWM output (cycle/duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P01 (TM8IOB) possible
Timer 9 ..................Square-wave output. PWM output (cycle/duty continuous variable). Event count. Pulse width measurement. Input
capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 1, 2
Synchronous type/Multi-master I2C × 1: Serial 4
Serial 4...................7-bit/10-bit address setting. General call

 I/O Pins
I/O 39 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 8 channels (with S/H)

 Extended Calculation
16-bit × 16-bit multiplication. 32-bit / 16-bit division

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port. Clock output

 ROM Correction
Correcting address designation: Up to 7 addresses possible

44 MAD00060FEM
 MN101EF34D

 Pin Assignment
TQFP048-P-0707B

P54, NBUZZER, KEY4, SBO2B, TXD2B

P53, BUZZER, KEY3, SBI2B, RXD2B
P70, SBO2A, TXD2A

P50, KEY0, TM1IOB

P51, KEY1, TM9IOB
P71, SBI2A, RXD2A

P52, KEY2, SBT2B

P66, SBO4, SDA4
P67, SBT4, SCL4

P64, TM4IOB
P63, TM3IOB
P65, SBI4
36
35
34
33
32
31
30
29
28
27
26
25
P72, SBT2A 37 24 CLKOUT, KEY5, P55
P75, SBO1B, TXD1B 38 23 KEY6, P56
P76, SBI1B, RXD1B 39 22 KEY7, P57
P77, SBT1B 40 21 RMOUTC, TM0IOC, IRQ6, P10
PA0, AN0, TM0IOA, RMOUTA 41 20 IRQ4, P24
PA1, AN1, TM1IOA 42 19 IRQ3, P23
PA2, AN2, TM2IOA 43 18 IRQ2, P22
PA3, AN3, TM3IOA 44 17 ACZ1, IRQ1, P21
PA4, AN4, TM4IOA 45 16 ACZ0, IRQ0, P20
PA5, AN5, TM7IOA 46 15 RMOUTB, TM2IOB, TM0IOB, LED3, P03
PA6, AN6, TM8IOA 47 14 SBT1A, TM4IOC, LED2, P02
PA7, AN7, TM9IOA 48 13 TXD1A, SBO1A, TM8IOB, LED1, P01
10

12
11
1
2
3
4
5
6
7
8
9 VDD5
MMOD

XO, P91
XI, P90
VSS
OSC1
OSC2

VDD18
DMOD
RXD1A, SBI1A, TM7IOB, LED0, P00
Vref+

NRST, P27

MAD00060FEM 45
 MN101E51 Series
Type MN101EF51A
Internal ROM type FLASH
ROM (byte) 32K
RAM (byte) 1K
Package (Lead-free) QFP044-P-1010F (Under development), TQFP048-P-0707B (Under planning)
50 ns (2.7 V to 5.5 V)
Minimum Instruction 125 ns (1.8 V to 5.5 V)
Execution Time *: at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used

 Interrupts
6 external interrupts. 19 internal interrupts
RESET. NMI. External 0 to 4. Timer 0 to 2. Timer 6. Timer 7 (2 systems). Timer 9 (3 systems). Time base. LIN. Serial 0 (2 systems).
Serial 1 (2 systems). Serial 4 (2 systems). A/D conversion. Low voltage detection

 Timer Counter
8-bit timer × 5
Timer 0 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Remote control carrier output. Simple
pulse width measurement. Real time output control
Timer 1 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 0, 1). Timer synchronous output
Timer 2 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Simple pulse width measurement. 24-bit
cascade connected (timer 0, 1, 2). Timer synchronous output. Real time output control
Timer 6 ..................8-bit freerun timer. Time base timer
Timer A..................Event count. Baud rate timer. Clock output for peripheral function
16-bit timer × 2
Timer 7 ..................Timer pulse output. Event count. High accuracy PWM. High performance IGBT output (cycle/duty continuous
variable). Timer synchronous output. Input capture (both edge available). Real time output control. Double buffer
compare register
Timer 9 ..................Timer pulse output. Event count. 3-phase PWM output. Triangular waveform output. Jigsaw waveform output.
Double buffer compare register
Watchdog timer × 2

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Multi-master I2C × 1: Serial 4

 I/O Pins
I/O 36 : Common use. Specified pull-up/pull-down resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 12 channels

 Special Ports
Remote control carrier output. High-current drive port. Buzzer output

 Reset
Low voltage detection. Automatic Reset. Reset factor detection

 Internal oscillation
High speed: 20 MHz. Low speed: 30 kHz

46 MAD00075CEM
 MN101EF51A

 Pin Assignment
QFP044-P-1010F, QFN044-P-0606A

P23, IRQ3, SBO0B, TXD0B

P35, TM2IOA, SBI1, RXD1

P22, IRQ2, SBI0B, RXD0B

P07, LED7, SBT4, SCL4

P21, IRQ1, SBT0B
P34, SBO1, TXD1
P33, NBUZZER
P32, BUZZER
P36, SBT1

P24, IRQ4

P20, IRQ0
33
32
31
30
29
28
27
26
25
24
23
RMOUTC, TM0IOC, P40 34 22 P06, SDA4, SBO4, LED6
TM1IOC, P41 35 21 P05, SBI4, TM9OD5, LED5
AN11, TM2IOC, P42 36 20 P04, RMOUTB, TM0IOB, TM9OD4, LED4
AN10, TM7IOC, P43 37 19 P03, TM1IOB, TM9OD3, LED3
TM9IOC, AN9, P44 38 18 P02, TM2IOB, TM9OD2, LED2
AN8, P45 39 17 P01, TM7IOB, TM9OD1, LED1
AN0, KEY0, PA0 40 16 P00, TM9IOA, TM9OD0, LED0
AN1, KEY1, SBT0A, PA1 41 15 P27, NRST
AN2, KEY2, SBI0A, RXD0A, PA2 42 14 MMOD
AN3, KEY3, SBO0A, TXD0A, PA3 43 13 P31, OCD_CLK
RMOUTA, AN4, KEY4, TM0IOA, PA4 44 12 P30, OCD_DATA

10
11
1
2
3
4
5
6
7
8
9
VDD5
VREF+

VDD18
DMOD
XO, OSC2, P26
XI, OSC1, P25
VSS
TM1IOA, KEY5, AN5, PA5
TM7IOA, KEY6, AN6, PA6
KEY7, AN7, PA7

ATRST

TQFP048-P-0707B
P23, IRQ3, SBO0B, TXD0B
P35, TM2IOA, SBI1, RXD1

P22, IRQ2, SBI0B, RXD0B

P07, LED7, SBT4, SCL4

P21, IRQ1, SBT0B
P34, SBO1, TXD1
P33, NBUZZER
P32, BUZZER
P36, SBT1

P24, IRQ4

P20, IRQ0
N.C.
36
35
34
33
32
31
30
29
28
27
26
25

N.C. 37 24 P06, SDA4, SBO4, LED6

RMOUTC, TM0IOC, P40 38 23 P05, SBI4, TM9OD5, LED5
TM1IOC, P41 39 22 P04, RMOUTB, TM0IOB, TM9OD4, LED4
AN11, TM2IOC, P42 40 21 P03, TM1IOB, TM9OD3, LED3
AN10, TM7IOC, P43 41 20 P02, TM2IOB, TM9OD2, LED2
TM9IOC, AN9, P44 42 19 P01, TM7IOB, TM9OD1, LED1
AN8, P45 43 18 P00, TM9IOA, TM9OD0, LED0
AN0, KEY0, PA0 44 17 N.C.
AN1, KEY1, SBT0A, PA1 45 16 P27, NRST
AN2, KEY2, SBI0A, RXD0A, PA2 46 15 MMOD
AN3, KEY3, SBO0A, TXD0A, PA3 47 14 P31, OCD_CLK
RMOUTA, AN4, KEY4, TM0IOA, PA4 48 13 P30, OCD_DATA
10

12
11
1
2
3
4
5
6
7
8
9
VDD5
VREF+

VDD18
N.C.
DMOD
XO, OSC2, P26
XI, OSC1, P25
VSS
TM1IOA, KEY5, AN5, PA5
TM7IOA, KEY6, AN6, PA6
KEY7, AN7, PA7

ATRST

MAD00075CEM 47
 MN101E52 Series
Type MN101EF52A
Internal ROM type FLASH
ROM (byte) 32K
RAM (byte) 1K
Package (Lead-free) TQFP032-P-0707A (Under development), UBGA036-P-0404AE (Under development)
50 ns (2.7 V to 5.5 V)
Minimum Instruction 125 ns (1.8 V to 5.5 V)
Execution Time *: at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used

 Interrupts
5 external interrupts. 17 internal interrupts
RESET. NMI. External 0 to 3. External 5. Timer 0 to 2. Timer 6. Timer 7 (2 systems). Timer 9 (3 systems). Time base. LIN. Serial 0 (2
systems). Serial 4 (2 systems). A/D conversion. Low voltage detection

 Timer Counter
8-bit timer × 5
Timer 0 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Remote control carrier output. Simple
pulse width measurement. Real time output control
Timer 1 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 0, 1). Timer synchronous output
Timer 2 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Simple pulse width measurement. 24-bit
cascade connected (timer 0, 1, 2). Timer synchronous output. Real time output control
Timer 6 ..................8-bit freerun timer. Time base timer
Timer A..................Event count. Baud rate timer. Clock output for peripheral function
16-bit timer × 2
Timer 7 ..................Timer pulse output. Event count. High accuracy PWM. High performance IGBT output (cycle/duty continuous
variable). Timer synchronous output. Input capture (both edge available). Real time output control. Double buffer
compare register
Timer 9 ..................Timer pulse output. Event count. 3-phase PWM output. Triangular waveform output. Jigsaw waveform output.
Double buffer compare register
Watchdog timer × 2

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0
Synchronous type/Multi-master I2C × 1: Serial 4

 I/O Pins
I/O 24 : Common use. Specified pull-up/pull-down resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 8 channels

 Special Ports
Remote control carrier output. High-current drive port

 Reset
Low voltage detection. Automatic Reset. Reset factor detection

 Internal oscillation
High speed: 20 MHz. Low speed: 30 kHz

48 MAD00076CEM
 MN101EF52A

 Pin Assignment
TQFP032-P-0707A

P04, LED4, TM9OD4, TM0IOB, RMOUTB

P03, LED3, TM9OD3, TM1IOB
P05, LED5, TM9OD5, SBI4
P22, IRQ2, SBI0B, RXD0B

P06, LED6, SDA4, SBO4

P07, LED7, SCL4, SBT4
P21, IRQ1, SBT0B
P20, IRQ0
24
23
22
21
20
19
18
17
TXD0B, SBO0B, IRQ3, P23 25 16 P02, TM2IOB, TM9OD2, LED2
KEY0, AN0, PA0 26 15 P01, TM7IOB, TM9OD1, LED1
SBT0A, KEY1, AN1, PA1 27 14 P00, TM9IOA, TM9OD0, LED0
RXD0A, SBI0A, KEY2, AN2, PA2 28 13 P27, NRST
TXD0A, SBO0A, KEY3, AN3, PA3 29 12 MMOD
RMOUTA, TM0IOA, KEY4, AN4, PA4 30 11 OCD_CLK, P31
TM1IOA, KEY5, AN5, PA5 31 10 OCD_DATA, P30
TM7IOA, KEY6, AN6, PA6 32 9 VSS
1
2
3
4
5
6
7
8
VDD5
VREF+

VDD18
DMOD
XO, OSC2, P26
XI, OSC1, P25
KEY7, AN7, PA7

ATRST

UBGA036-P-0404AE
A B C D E F

P23, IRQ3, P22, IRQ2, P06, LED6, P07, LED7, P05, LED5,
6 SBO0B, SBI0B, P20, IRQ0 SBO4, SBT4, SBI4, 6
TXD0B RXD0B SDA4 SCL4 TM9OD5

P04, LED4,
PA, AN1, P02, LED2,
PA0, AN0, TM0IOB,
5 KEY1, N.C. N.C. TM2IOB, 5
KEY0 TM9OD4,
SBT0A TM9OD2
RMOUTB

PA3, AN3, PA2, AN2,

P01, LED1, P00, LED0, P03, LED3,
KEY3, KEY2, P21, IRQ1,
4 TM7IOB, TM9IOA, TM1IOB, 4
SBO0A, SBI0A, SBT0B
TM9OD1 TM9OD0 TM9OD3
TXD0A RXD0A

PA2, AN2,
PA5, AN5,
KEY2, P31, P30,
3 KEY5, ATRST P27, NRST 3
SBI0A, OCD_CLK OCD_DATA
TM1IOA
RXD0A

PA4, AN4,
PA6, AN6,
KEY4, P26, OSC2,
2 KEY6, VSS DMOD MMOD 2
TM0IOA, XO
TM7IOA
RMOUTA

PA7, AN7, P25, OSC1,

1 VREF+ VDD5 VDD18 VSS 1
KEY7 XI

A B C D E F

MAD00076CEM 49
 MN101C49 Series
Type MN101C49G MN101C49H MN101C49K MN101CF49K MN101CP49K
Internal ROM type Mask ROM FLASH EPROM
ROM (byte) 128K 160K 224K
RAM (byte) 4K 6K 10K
Package (Lead-free) LQFP100-P-1414, QFP100-P-1818B
[Standard]
0.10 µs (at 4.5 V to 5.5 V, 20 MHz)
0.238 µs (at 2.7 V to 5.5 V, 8.39 MHz)
125 µs (at 2.0 V to 5.5 V, 32 kHz)*
Minimum Instruction [Double speed]
Execution Time 0.12 µs (at 4.5 V to 5.5 V, 8.39 MHz)
0.25 µs (at 3.0 V to 5.5 V, 4 MHz)
62.5 µs (at 2.0 V to 5.5 V, 32 kHz)*
*: The lower limit for operation guarantee for EPROM built-in type is 2.3 V.
The lower limit for operation guarantee for flash memory built-in type is 4.5 V.

 Interrupts
RESET. Watchdog. External 0 to 5. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Time base. Serial 0 to 3. Automatic transfer finish. A/D
conversion finish. Key interrupts (8 lines)

 Timer Counter
8-bit timer × 6
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Pulse width measurement
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event. Pulse width measurement
Timer 3 ..................Square-wave output. Event count. Remote control carrier output
Timer 4 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial 1 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
width measurement. Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0
Synchronous type/Simple UART (half-duplex) × 1: Serial 1
Synchronous type × 1: Serial 2
Synchronous type/Single-master I2C × 1: Serial 3

 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 73 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
(72) : Flash memory built-in type
Input 15 : Common use. Specified pull-up resistor available
(14) : Flash memory built-in type

 A/D converter
10-bit × 8 channels (with S/H)

 D/A converter
8-bit × 4 channels

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

50 MAD00011LEM
 MN101C49G, MN101C49H, MN101C49K, MN101CF49K, MN101CP49K

 ROM Correction
Correcting address designation: Up to 3 addresses possible

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 30 70 mA
Operating supply current IDD2 fosc = 8.39 MHz. VDD = 5 V 15 30 mA
IDD3 fx = 32.768 kHz. VDD = 3 V 40 120 µA
IDD4 fx = 32 kHz. VDD = 3 V (5 V). Ta = 25 °C 5(13) 11(30) µA
Supply current at HALT
IDD5 fx = 32.768 kHz. VDD = 3 V (5 V). Ta = 85 °C 30(90) µA
IDD6 VDD = 5 V. Ta = 25 °C 3 µA
Supply current at STOP
IDD7 VDD = 5 V. Ta = 85 °C 60 µA
Note) ( ): Flash memory built-in type

 Pin Assignment
QFP100-P-1818B, LQFP100-P-1414

P47, KEY7
P46, KEY6
P45, KEY5
P44, KEY4
P43, KEY3
P42, KEY2
P41, KEY1
P50, NWE
P51, NRE
P52, NCS
P74, A12

P72, A10

P54, A17
P53, A16
P73, A11

P71, A9
P70, A8
P67, A7
P66, A6
P65, A5
P64, A4
P63, A3
P62, A2
P61, A1
P60, A0
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
A13, P75 76 50 P40, KEY0
A14, P76 77 49 P37, NDKDMA
A15, P77 78 48 P36, NSTDMA
D0, LED0, P80 79 47 P35, NLDDMA, SCL, SBT3
D1, LED1, P81 80 46 P34, NBT, SBI3
D2, LED2, P82 81 45 P33, NBR, SDA, SBO3
D3, LED3, P83 82 44 P32, SBT1
D4, LED4, P84 83 43 P31, RXD1, SBI1
D5, LED5, P85 84 42 P30, TXD1, SBO1
D6, LED6, P86 85 41 P17(VPP)
D7, LED7, P87 86 40 P16, TM4IO
SDO0, PD0 87 39 P15
SDO1, PD1 88 38 P14, TM7IO
SDO2, PD2 89 37 P13, TM3IO
SDO3, PD3 90 36 P12, TM2IO
SDO4, PD4 91 35 P11, TM1IO
SDO5, PD5 92 34 P10, TM0IO, RMOUT
SDO6, PD6 93 33 P27, NRST
SDO7, PD7 94 32 P26(VDD2)
DAVSS 95 31 P25, IRQ5
DA0, PC0 96 30 P24, IRQ4
DA1, PC1 97 29 P23, IRQ3
DA2, PC2 98 28 P22, IRQ2
DA3, PC3 99 27 P21, IRQ1, SENS
DAVDD 100 26 P20, IRQ0
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
VREF-

VREF+
VDD
OSC2
OSC1
VSS
XI
XO
MMOD
SBO0, P00
SBI0, P01
SBT0, P02
SBO2, P03
SBI2, P04
SBT2, P05
NDK, BUZZER, P06
SYSCLK, P07
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6
AN7, PA7

Note) ( ): Flash memory built-in type

MAD00011LEM 51
 MN101C77 Series
Type MN101C77A MN101C77C MN101C77D MN101C77F MN101CF77G
Internal ROM type Mask ROM FLASH
ROM (byte) 32K 48K 64K 96K 128K
RAM (byte) 1.5K 3K 6K
LQFP064-P-1414, LQFP064-P-1414,
Package (Lead-free) LQFP064-P-1414 LQFP064-P-1414
TQFP064-P-1010C TQFP064-P-1010C
[Standard]
0.1 µs (at 2.5 V to 3.6 V, 20 MHz)*
0.2 µs (at 2.1 V to 3.6 V, 10 MHz)*
Minimum Instruction 0.5 µs (at 1.8 V to 3.6 V, 4 MHz)*
Execution Time 62.5 µs (at 1.8 V to 3.6 V, 32 kHz)*
[Double speed]
0.119 µs (at 2.5 V to 3.6 V, 8.39 MHz)*
*: The operation guarantee range for flash memory built-in type is 2.7 V to 3.6 V.

 Interrupts
RESET. Watchdog. External 0 to 4. Timer 0. Timer 1. Timer 4 to 6. Timer 7 (2 systems). Time base. Serial 0 reception. Serial 0
transmission. Serial 1 reception. Serial 1 transmission. Serial 3. Serial 4. Automatic transfer finish. A/D conversion finish. Key interrupts (8
lines)

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Pulse width measurement
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 4 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial 1 baud rate timer
Timer 5 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial 0 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
width measurement. Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Single-master I2C × 1: Serial 3
I2C slave × 1: Serial 4
Serial 4...................I2C high-speed transfer mode. 7-bit/10-bit address setting. General call

 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 53 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 7 channels (with S/H)

 D/A converter
8-bit × 2 channels (Serves as AD pin, as well)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 3 addresses possible

52 MAD00038MEM
 MN101C77A, MN101C77C, MN101C77D, MN101C77F, MN101CF77G

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz (fs = fosc/2). VDD = 3.3 V 6 12 mA
Operating supply current IDD2 fosc = 8.39 MHz (fs = fosc/2). VDD = 3.3 V 3 6 mA
IDD3 fx = 32.768 kHz (fs = fx/2). VDD = 3.3 V 40 µA
IDD4 fx = 32.768 kHz. VDD = 3.3 V. Ta = 25 °C 5 10 µA
Supply current at HALT
IDD5 fx = 32.768 kHz. VDD = 3.3 V 40 µA
IDD6 VDD = 3.3 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD7 VDD = 3.3 V. Ta = 85 °C 30 µA
Ta = -40 °C to +85 °C. VDD = 1.8 V to 3.6 V. VSS = 0 V

 Pin Assignment
LQFP064-P-1414, TQFP064-P-1010C [MN101C77C]
P73, SB00B, TXD0B

P70, SB01B, TXD1B

P71, SBI1B, RXD1B

P67, SD07, KEY7

P66, SD06, KEY6
P65, SD05, KEY5
P64, SD04, KEY4
P63, SD03, KEY3
P62, SD02, KEY2
P61, SD01, KEY1
P60, SD00, KEY0

P51, SB03, SDA3

P52, SBT3, SCL3
P53, SDA4B
P72, SBT1B

P54, SCL4B
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
P74, SBI0B, RXD0B 49 33 32 SBI3, P50
P75, SBT0B 50 31 IRQ4, P24
P76, TCI01 51 30 IRQ3, P23
P77, TCI05 52 29 IRQ2, P22
P87, LED7 53 28 ACZ, IRQ1, P21
P86, LED6 54 27 IRQ0, P20
P85, LED5 55 26 TCI07, P14
P84, LED4 56 25 TCI04B, P13
P83, LED3 57 24 TC04A, P12
P82, LED2 58 23 TCI00B, P11
P81, LED1 59 22 RMOUT, TC00A, P10
P80, LED0 60 21 BUZZER, P06
AVSS 61 20 SBT0A, P05
PA0, AN0, DA0 62 19 RXD0A, SBI0A, P04
PA1, AN1, DA1 63 18 TXD0A, SB00A, P03
PA2, AN2 64 17 SCL4A, SBT1A, P02
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9
N.C. (VPP)

VDD
OSC2
OSC1
VSS
XI
XO
MMOD

TXD1A, SB01A, P00

SDA4A, RXD1A, SBI1A, P01
NRST, P27
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6

AVDD

Note) Pin 5 serves as the VPP pin in the MN101CF77G, and cannot be used as a user pin.

MAD00038MEM 53
 MN101E01 Series
Type MN101E01J MN101E01K MN101E01L MN101E01M MN101EF01M
Internal ROM type Mask ROM FLASH
ROM (byte) 192K 256K 320K 384K
RAM (byte) 10K 14K 20K 24K
Package (Lead-free) QFP100-P-1818B LQFP100-P-1414, QFP100-P-1818B
[Standard] [Standard]
0.0625 µs (at 3.0 V to 3.6 V, 32 MHz) 0.0625 µs (at 3.0 V
Minimum Instruction 0.1 µs (at 3.0 V to 3.6 V, 20 MHz) to 3.6 V, 32 MHz)
Execution Time 62.5 µs (at 3.0 V to 3.6 V, 32 kHz) [Double speed]
[Double speed] 0.10 µs (at 3.0 V to
0.10 µs (at 3.0 V to 3.6 V, 10 MHz) 3.6 V, 10 MHz)

 Interrupts
RESET. Watchdog. External 0 to 5. Timer 0 to 6. Timer 7 (2 systems). Time base. Serial 0 (2 systems). Serial 1 (2 systems). Serial 2.
Serial 3. Serial 4 (2 systems). Automatic transfer finish. A/D conversion finish. Key interrupts (8 lines)

 Timer Counter
8-bit timer × 7
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Pulse width measurement. Real time
output control
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event. Pulse width measurement. Real time
output control. Serial baud rate timer
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial baud rate timer
Timer 4 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial baud rate timer
Timer 5 ..................Square-wave output. Event count. Serial baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 4, 5 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
width measurement. Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 3: Serial 0, 1, 4
Synchronous type/Single-master I2C × 2: Serial 2, 3

 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 34 : (5 V I/F port) Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
50 : (3 V I/F port) Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 8 channels (with S/H)

 D/A converter
8-bit × 1 channels

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 3 addresses possible

54 MAD00034PEM
 MN101E01J, MN101E01K, MN101E01L, MN101E01M, MN101EF01M

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 32.0 MHz (fs = fosc/2). VDD1 = 3.3 V 11(48) 30(80) mA
Operating supply current IDD2 fosc = 20.0 MHz (fs = fosc/2). VDD1 = 3.3 V 8(43) 22(75) mA
IDD3 fosc = 32.768 kHz (fs = fosc/2). VDD1 = 3.3 V 30(60) 120(180) µA
Supply current at HALT IDD4 fx = 32.768 kHz. VDD1 = 3.3 V 12 30 µA
IDD5 VDD1 = 3.3 V. Ta = 25 °C 0.3 3.0 µA
Supply current at STOP
IDD6 VDD1 = 3.3 V. Ta = 85 °C 80 µA
Note) ( ): Flash memory built-in type

 Pin Assignment
QFP100-P-1818B, LQFP100-P-1414
P40, SBO4, TXD4

P76, SDO6, NWE

P41, SBI4, RXD4

P77, SDO7, NDK

P75, SDO5, NRE

P74, SDO4, NCS

P67, KEY7, A15

P66, KEY6, A14
P65, KEY5, A13
P64, KEY4, A12
P73, SDO3, A19
P72, SDO2, A18
P71, SDO1, A17
P70, SDO0, A16
P87, LED7, D7
P86, LED6, D6
P85, LED5, D5
P84, LED4, D4
P83, LED3, D3
P82, LED2, D2
P81, LED1, D1
P80, LED0, D0
P42, SBT4

VSS2
P43
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
TXD0B, SBO0B, P90 76 50 P63, KEY3, A11
RXD0B, SBI0B, P91 77 49 P62, KEY2, A10
SBT0B, P92 78 48 P61, KEY1, A9
SDA3B, SBO3B, P93 79 47 P60, KEY0, A8
SBI3B, P94 80 46 P57, A7
SCL3B, SBT3B, P95 81 45 P56, A6
IRQ2B, PD0 82 44 P55, A5
IRQ3B, PD1 83 43 P54, A4
TM4IOB, PD2 84 42 P53, A3
TM5IOB, PD3 85 41 P52, A2
TM7IOB, PD4 86 40 P51, A1
BUZZER, PD5 87 39 P50, A0
SYSCLK, PD6 88 38 P35, SBT3A, SCL3A
VDD3 89 37 P34, SBI3A
PD7 90 36 P33, SBO3A, SDA3A
VSS3 91 35 P32, SBT1
AN0, PA0 92 34 P31, SBI1, RXD1
AN1, PA1 93 33 P30, SBO1, TXD1
AN2, PA2 94 32 P25, IRQ5
AN3, PA3 95 31 P24, IRQ4
AN4, PA4 96 30 P23, IRQ3A
AN5, PA5 97 29 P22, IRQ2A
AN6, PA6 98 28 P21, IRQ1
AN7, PA7 99 27 P20, IRQ0
VREF+ 100 26 P16, TM7IOA
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
VDD1

VSS1

VDD2
DA0, P06

TXD0A, SBO0A, P00

RXD0A, SBI0A, P01
SBT0A, P02
SDA2, SBO2, P03
SBI2, P04
SCL2, SBT2, P05

MM0D
OSC2
OSC1

XI
XO

MOD1

TM2IO, P12
TM3IO, P13
TM4IOA, P14
TM5IOA, P15
TM1IO, P11
NRST, P27
RMOUT, TM0IO, P10
DAVDD

DAVSS

Note) Pin 63 to Pin 100: 5 V I/F port

MAD00034PEM 55
 MN101C93 Series
Type MN101C93K MN101CF93K
Internal ROM type Mask ROM FLASH
ROM (byte) 224K
RAM (byte) 6K
Package (Lead-free) LQFP100-P-1414
Minimum Instruction 0.125 µs (at 3.0 V to 3.6 V, 8 MHz) 0.167 µs (at 3.0 V to 3.6 V, 6 MHz)
Execution Time 62.5 µs (at 3.0 V to 3.6 V, 32 kHz) 62.5 µs (at 3.0 V to 3.6 V, 32 kHz)

 Interrupts
RESET. Watchdog. External 0 to 5. External 6 (key interrupt dedicated). Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems).
Time base. Serial 0 (2 systems). Serial 1 (2 systems). Serial 3 (1 systems). A/D conversion finish. Automatic transfer finish. USB
interrupts

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Added pulse (2-bit) type PWM output. Square-wave/PWM output to large current terminal PC3 possible
Timer 1 ..................Square-wave output. Event count. Serial transfer clock output. Synchronous output event
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. PWM output. Serial transfer clock output. Event
count. Synchronous output event. Simple pulse width measurement. Square-wave/PWM output to large current
terminal PC5 possible
Timer 3 ..................Square-wave output. Event count. Serial transfer clock output
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output
event. Pulse width measurement. Input capture. Real time output control. High performance IGBT output. Square-
wave/PWM output to large current terminal PC4 possible
Timer 8 ..................Square-wave/16-bit PWM output (duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal PC6 possible
Timer 7, 8 can be cascade-connected: Square-wave output, PWM is possible as a 32-bit timer
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Single-master I2C × 1: Serial 3

 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 USB Functions
Conforms to USB 1.1: Full-speed (12 Mbps) supported
USB transceiver built-in. 5 end points (FIFO built-in independently)
FIFO size: EP0 = 16 bytes. EP1 = 128 bytes. EP2 = 128 bytes. EP3 = 64 bytes. EP4 = 64 bytes
EP0: Control transfer. IN/OUT (two ways)
EP1 to EP4: Interrupt/Bulk/Isochronous transfer supported. Settable to IN or OUT. Double Buffering function supported
When the MAXP size is set to a half or less of the MAXFIFO size for each EP, the Double Buffering function is made valid
automatically

 I/O Pins
I/O 84 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 12 channels (with S/H)

56 MAD00056GEM
 MN101C93K, MN101CF93K

 Display control function

LCD: 47 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
LCD power supply separated from VDD (usable if VDD = VLCD ≤ 3.6 V)
LCD power shunt resistance contained

 Special Ports
USB ports (D+, D–). Buzzer output. Inverted buzzer output. Remote control carrier output. High-current drive port. Clock output

 Pin Assignment
LQFP100-P-1414

P02, SEG44, SYSCLK, SBT3, SCL3

P03, SEG43, NDK, SBO3, SDA3
P47, SEG32, D7, KEY7, SDO7
P46, SEG33, D6, KEY6, SDO6
P45, SEG34, D5, KEY5, SDO5
P44, SEG35, D4, KEY4, SDO4
P43, SEG36, D3, KEY3, SDO3
P42, SEG37, D2, KEY2, SDO2
P41, SEG38, D1, KEY1, SDO1
P40, SEG39, D0, KEY0, SDO0

P01, SEG45, NBUZZER

P04, SEG42, NCS, SBI3

P00, SEG46, BUZZER

P05, SEG41, NWE
P06, SEG40, NRE
P56, SEG25, A6
P55, SEG26, A5
P54, SEG27, A4
P53, SEG28, A3
P52, SEG29, A2
P51, SEG30, A1
P50, SEG31, A0

P25, IRQ5
P24, IRQ4
P23, IRQ3
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
P57, SEG24, A7 76 50 IRQ2, P22
P60, SEG23, A8 77 49 IRQ1, P21
P61, SEG22, A9 78 48 IRQ0, P20
P62, SEG21, A10 79 47 TM8IO, P15
P63, SEG20, A11 80 46 TM7IO, P14
P64, SEG19, A12 81 45 TM3IO, P13
P65, SEG18, A13 82 44 TM2IO, P12
P66, SEG17, A14 83 43 TM1IO, P11
P67, SEG16, A15 84 42 RMOUT, TM0IO, P10
P70, SEG15, A16 85 41 RXD1, SBI1, AN11, PB7
P71, SEG14, A17 86 40 TXD1, SBO1, AN10, PB6
P72, SEG13 87 39 SBT1, AN9, PB5
P73, SEG12 88 38 RXD0A, SBI0A, AN8, PB4
P74, SEG11 89 37 TXD0A, SBO0A, AN7, PB3
P75, SEG10 90 36 SBT0A, AN6, PB2
P76, SEG9 91 35 VSS
P77, SEG8 92 34 D-
P80, SEG7 93 33 D+
P81, SEG6 94 32 VDD
P82, SEG5 95 31 AN5, PA5
P83, SEG4 96 30 AN4, PA4
P84, SEG3 97 29 AN3, PA3
P85, SEG2 98 28 AN2, PA2
P86, SEG1 99 27 AN1, PA1
P87, SEG0 100 26 AN0, PA0
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
COM0, P90
COM1, P91
COM2, P92
COM3, P93
VLC3, P94
VLC2
VLC1
N.C.
RXD0B, SBI0B, LED0, PC0
TXD0B, SBO0B, LED1, PC1
SBT0B, LED2, PC2
TM0O, LED3, PC3
TM7O, LED4, PC4
TM2O, LED5, PC5
TM8O, LED6, PC6
VSS
OSC1
OSC2
VDD
XI
XO
MMOD

DMOD
VREF+
NRST, P27

MAD00056GEM 57
 MN101E35 Series
Type MN101E35A MN101E35D MN101EF35A MN101EF35D
Internal ROM type Mask ROM FLASH
ROM (byte) 32K 68K 32K 64K+4K
RAM (byte) 4K
Package (Lead-free) TQFP048-P-0707B
0.042 µs (at 2.2 V to 3.6 V, 24 MHz, When USB unused)
Minimum Instruction 0.0625 µs (at 3.0 V to 3.6 V, 16 MHz, When USB used)
Execution Time 62.5 µs (at 2.2 V to 3.6 V, 32 kHz)

 Interrupts
RESET. Watchdog. External 0 to 4. External 5 (key interrupt dedicated). External 6. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8
(2 systems). Timer 9 (2 systems). Time base. Serial 1 (2 systems). Serial 2 (2 systems). Serial 4 (2 systems). A/D conversion finish. USB
interrupts

 Timer Counter
8-bit timer × 6
Timer 0 ..................Square-wave output. PWM output. Event count. Simple pulse width measurement. Square-wave/PWM output to
large current terminal P03 (TM0IOB) possible
Timer 1 ..................Square-wave output. Event count
Timer 2 ..................Square-wave output. PWM output. Event count. Simple pulse width measurement. Square-wave/PWM output to
large current terminal P03 (TM2IOB) possible
Timer 3 ..................Square-wave output. Event count
Timer 4 ..................Square-wave output. PWM output. Event count. Simple pulse width measurement. Square-wave/PWM output to
large current terminal P02 (TM4IOC) possible
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 0, 1, 2 can be cascade-connected
Timer 0, 1, 2, 3 can be cascade-connected
16-bit timer × 3
Timer 7 ..................Square-wave output. PWM output (cycle/duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P00 (TM7IOB) possible
Timer 8 ..................Square-wave output. PWM output (cycle/duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P01 (TM8IOB) possible
Timer 9 ..................Square-wave output. PWM output (cycle/duty continuous variable). Event count. Pulse width measurement. Input
capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 1, 2
Synchronous type/Multi-master I2C × 1: Serial 4
Serial 4...................7-bit/10-bit address setting. General call

 USB Functions
Conforms to USB 2.0: Full-speed (12 Mbps) supported
USB transceiver built-in. 3 end points (FIFO built-in independently)
FIFO size: EP0 = 16 bytes. EP1 = 128 bytes. EP2 = 128 bytes
EP0: Control transfer. IN/OUT (two ways)
EP1 to EP2: Interrupt/Bulk/Isochronous transfer supported. Settable to IN or OUT. Double Buffering function supported
When the MAXP size is set to a half or less of the MAXFIFO size for each EP, the Double Buffering function is made valid
automatically

 I/O Pins
I/O 37 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 8 channels (with S/H)

58 MAD00061FEM
 MN101E35A, MN101E35D, MN101EF35A, MN101EF35D

 Extended Calculation
16-bit × 16-bit multiplication. 32-bit / 16-bit division

 Special Ports
USB ports (D+, D–). Buzzer output. Remote control carrier output. High-current drive port. Clock output

 ROM Correction
Correcting address designation: Up to 7 addresses possible

 Pin Assignment
TQFP048-P-0707B

P54, NBUZZER, KEY4, SBO2B, TXD2B

P53, BUZZER, KEY3, SBI2B, RXD2B
P70, SBO2A, TXD2A

P50, KEY0, TM1IOB

P51, KEY1, TM9IOB
P71, SBI2A, RXD2A

P52, KEY2, SBT2B

P66, SBO4, SDA4
P67, SBT4, SCL4

P64, TM4IOB
P63, TM3IOB
P65, SBI4
36
35
34
33
32
31
30
29
28
27
26
25

P72, SBT2A 37 24 CLKOUT, KEY5, P55

P75 38 23 KEY6, P56
D- 39 22 KEY7, P57
D+ 40 21 RMOUTC, TM0IOC, IRQ6, P10
PA0, AN0, TM0IOA, RMOUTA 41 20 IRQ4, P24
PA1, AN1, TM1IOA 42 19 IRQ3, P23
PA2, AN2, TM2IOA 43 18 IRQ2, P22
PA3, AN3, TM3IOA 44 17 IRQ1, P21
PA4, AN4, TM4IOA 45 16 IRQ0, P20
PA5, AN5, TM7IOA 46 15 RMOUTB, TM2IOB, TM0IOB, LED3, P03
PA6, AN6, TM8IOA 47 14 SBT1, TM4IOC, LED2, P02
PA7, AN7, TM9IOA 48 13 TXD1, SBO1, TM8IOB, LED1, P01
10

12
11
1
2
3
4
5
6
7
8
9
MMOD

XO, P91
XI, P90
VSS
OSC1
OSC2
VDD33
VDD18
DMOD
RXD1, SBI1, TM7IOB, LED0, P00
Vref+

NRST, P27

MAD00061FEM 59
 MN101D06 Series
Type MN101D06F MN101D06G MN101D06H MN101DF06Z
Internal ROM type Mask ROM FLASH
ROM (byte) 96K 128K 160K 224K
RAM (byte) 3K 4K 5K 6K
Package (Lead-free) QFP100-P-1818B
0.1397 µs (at 4.0 V to 5.5
[When using main clock] V, 14.32 MHz)
0.1397 µs (at 4.0 V to 5.5 V, 14.32 MHz) 71.5 µs (at 3.0 V to 5.5
Minimum Instruction 71.5 µs (at 3.0 V to 5.5 V, 14.32 MHz internal frequency division) V, 14.32 MHz internal
Execution Time [When using sub clock] frequency division)
61 µs (at 2.2 V to 5.5 V, 32.768 kHz) 61 µs (at 2.5 V to 5.5 V,
32.768 kHz)

 Interrupts
RESET. Runaway. External 0 to 4. Key input (P50 to P54). Timer 0 to 4. Timer 6. Timer 7. Capstan FG. Control. HSW. Cylinder(Drum)
FG. Servo V-sync. Synchronous output. OSD. XDS. Serial 0 to 2. A/D (common with PWM 4 reference frequency). OSDV-sync

 Timer Counter
8-bit timer × 1 or 4-bit timer × 2
Timer 7 ..................Timer function. Event count
16-bit timer × 6
Timer 0 ..................Timer function. Max. 2 s or max. 36 h at cascade-connecting with timer 6
Timer 1 ..................Timer function. Linear timer counter function
Timer 2 ..................Timer function. Input capture. Duty judgment of CTL signal (VISS/VASS detection function)
Timer 3 ..................Timer function. Detection of serial indexing. Generation of remote control output carrier frequency
Timer 4 ..................Timer function. Event count (P15 input). Serial transfer clock output
Timer 6 ..................Clock function (max. 2 s)
19-bit timer × 1
Timer 5 ..................Watchdog. Stable oscillation waiting function

 Serial interface
Synchronous type/Start-stop synchronous type × 1: Serial 0 (8-bit)
Serial 0...................Transfer direction of MSB/LSB selectable
Synchronous type/Remote control transmission/Simple remote control receive × 1: Serial 1 (8-bit)
Serial 1...................Transfer direction of MSB/LSB selectable. Start condition function
I2C × 1: Serial 2 (8-bit)
Serial 2...................Master transmission/reception. Slave transmission/reception

 OSD
OSD mode: Accommodation with menu (internal synchronous) or super impose (external synchronous) display
Applicable broadcasting system......NTSC. PAL. PAL-M. PAL-N
Screen configuration .......... 24 characters × 2n rows (n = 1 to 6)
Character type .......Max. 512 character types (variable, incude special characters)
Character size ........12 dots × 18 dots (vertical direction: 1 dot for 2H at not enlargement)
Enlarged characters .......Each × 2, × 3 or × 4 settings in horizontal and vertical
Character interpolation....... None
Line background color ....... 8-hue settable (settable in the row unit at menu display)
Line background intensity.. 8 gradations settable in the row unit (at output of composite video signal)
Screen background color.... 8-hue settable (at output of composite video signal menu display)
Character color ......White (at output of composite video signal)
Character intensity ........8 gradations settable in the row unit (at output of composite video signal)
Frame function ......1-dot frame in 4 or 8 directions
Frame intensity ......4 gradations settable in the row unit (at output of composite video signal)
Box shade function........Settable in the character unit (at output of composite video signal with 129 or more characters (character types))
Blinking .................None (covered by software)
Inverted character ..........Settable in the character unit
Halftone .................Settable in the row unit in 2 intensity gradations (at output of external synchronous composite video signal)

60 MAD00029KEM
 MN101D06F, MN101D06G, MN101D06H, MN101DF06Z

CCD mode: Supports Closed Caption in the U.S.A.

Screen configuration .......... 32 characters × 16 rows
Character type .......Max. 128 character types (variable)
Character size ........12 × 26 dots (Vertical direction : 1 dot for 1H, including 8 dots in the underlined area)
Enlarged characters .......None
Character interpolation....... None
Line background color ....... 8-hue settable
Line background intensity.. 8 gradations settable in the row unit (at output of composite video signal)
Screen background color.... 8-hue settable (at output of composite video signal)
Character color ......8 colors (at RGB output). White (at output of composite video signal)
Character intensity ........8 gradations settable in the row unit (at output of composite video signal)
Frame function ......None
Box shade function........None
Inverted character ..........None
Halftone .................Settable in the row unit in 2 intensity gradations (at output of external synchronous composite video signal)
Others ....................Underline. Italic. Blinking function. Scroll
Common
Input ......................Composite video signal input (output level:1 V[p-p] / 2 V[p-p])
Clamp method .......Sync tip clamp. Clamp level in 4 levels
Output ....................Composite video output. Digital output (6 pins)
Measure against image fluctuation......Built-in AFC circuit
Dot clock ...............1/2 of OSC oscillation clock (automatic phase adjustment)

 XDS
Built-in U.S. closed caption data slicer: Optional 2 line data can be extracted

 I/O Pins
I/O 75 : Common use: 66
Input 2 : Common use: 2

 A/D converter
8-bit × 13 channels (without S/H)

 PWM
13-bit × 2 channels (at repetition cycle 572 µs at 14.32 MHz)
10-bit × 2 channels (at repetition cycle 71.5 µs at 14.32 MHz)
8-bit × 1 channels (at repetition cycle 71.5 ms, 0.572 ms, 1.14 ms, 2.29 ms at 14.32 MHz)

 ICR
18-bit × 6 channels

 OCR
16-bit × 2: 8-bit synchronous output. 4-bit 3-state synchronous output
16-bit × 1: Weak electric field V-sync backup.
16-bit × 1: Rec CTL

 Special Ports
Buzzer output. 3-state output VLP pin. Remote control reception
CTL signal input terminal. Capstan FG inputterminal. Sylinder(Durm) PG/FG input terminals. Head Amp/Rortary control output
terminals
Output of 1/2 OSC oscillation clock (2 V[p-p]). Output of 1/4 OSC oscillation clock (1 V[p-p])

 ROM Correction
Correcting address designation: Up to 3 addresses possible
Correction method: Correction program being saved in internal RAM

MAD00029KEM 61
 Electrical Charactreistics (Supply current)
Limit
Parameter Symbol Condition Unit
min typ max
IDD1 14.32 MHz oscillation without load. VDD = 5 V 60 100 mA
Operating supply current
IDD2 1/1024 of 14.32 MHz operation without load. VDD = 3.0 V 2 5 mA
Stop of 14.32 MHz oscillation
Operating supply current IDD3 50 100 µA
32 kHz oscillation operation without load. VDD = 2.7 V
Supply current at STOP IDSP Stop of oscillation without load. VDD = 5 V. Ta = 55 °C 10 µA
IDHT0 14.32 MHz oscillation without load. VDD = 5 V 5 15 mA
Supply current at HALT Stop of 14.32 MHz oscillation
IDHT1 5 20 µA
32 kHz oscillation operation without load. VDD = 2.7 V
Ta = 25 °C±2 °C. VSS = 0 V

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Conversion relative error ∆NLAD ±3 LSB
A/D conversion time tAD fosc = 14.32 MHz 8 µs
Analog input voltage 5 V
Ta = 25 °C±2 °C. VDD = 5.0 V. VSS = 0 V

 Pin Assignment
QFP100-P-1818B

AFCLPF
FSCLPF
SECAM
RCTLN
RCTLP

PGMM
VOW1
VOW2
VOW3
VOW4
AVDD

VDD2
CTLA

VOB1
VOB2

AFCC
AVSS

VRO

FSCI
AFG

YPG
YFG
FGF
VRI

PA6
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51

CO 76 50 CVIN2
TPZ 77 49 CVIN
AD11 78 48 VSS2
AD10 79 47 CVOUT
AD9 80 46 HSYNC
AD8 81 45 VSYN
AD7 82 44 OSCO2
AD6 83 43 OSCI2
AD5 84 42 SXI
AD4 85 41 XO
AD3 86 40 XI
AD2 87 39 VSS
AD1 88 38 OSCI
AD0 89 37 OSCO
P77 90 36 VDD
P76 91 35 SBUFD0
P75 92 34 PWM0
P74 93 33 PWM1
P73 94 32 SBUFD1
P72 95 31 SBUFD2
P71 96 30 SBUFD3
P70 97 29 SBUFD4
ROTA 98 28 SBUFD5
HAMP 99 27 SBUFD6
DENV 100 26 SBUFD7
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
KEYIRQ4
KEYIRQ3
KEYIRQ2
KEYIRQ1
KEYIRQ0
NSBT1
NSBI1
NSBO1
NSBT0
NSBI0
NSBO0
SDA
SCK
HBUFD6, BUZZER
HBUFD4
HBUFD2, DAOUT
HBUFD0
HSW
VLP
NRST

62 MAD00029KEM
63
 MN101D07 Series
Type MN101D07G MN101D07H MN101DF07Z
Internal ROM type Mask ROM FLASH
ROM (byte) 128K 160K 224K
RAM (byte) 4K 5K 6K
Package (Lead-free) LQFP112-P-2020
0.1397 µs
[When using main clock] (at 4.0 V to 5.5 V, 14.32 MHz)
0.1397 µs (at 4.0 V to 5.5 V, 14.32 MHz)
Minimum Instruction 71.5 µs (at 3.0 V to 5.5 V, 14.32
71.5 µs (at 3.0 V to 5.5 V, 14.32 MHz internal frequency division)
Execution Time MHz internal frequency division)
[When using sub clock] 61 µs
61 µs (at 2.2 V to 5.5 V, 32.768 kHz) (at 2.5 V to 5.5 V, 32.768 kHz)

 Interrupts
RESET. Runaway. External 0 to 4. Key input (P50 to P54). Timer 0 to 4. Timer 6. Timer 7. Capstan FG. Control. HSW. Cylinder(Drum)
FG. Servo V-sync. Synchronous output. OSD. XDS. Serial 0 to 2. A/D (common with PWM 4 reference frequency). OSDV-sync

 Timer Counter
8-bit timer × 1 or 4-bit timer × 2
Timer 7 ..................Timer function. Event count
16-bit timer × 6
Timer 0 ..................Timer function. Max. 2 s or max. 36 h at cascade-connecting with timer 6
Timer 1 ..................Timer function. Linear timer counter function
Timer 2 ..................Timer function. Input capture. Duty judgment of CTL signal (VISS/VASS detection function)
Timer 3 ..................Timer function. Detection of serial indexing. Generation of remote control output carrier frequency
Timer 4 ..................Timer function. Event count (P15 input). Serial transfer clock output
Timer 6 ..................Clock function (max. 2 s)
19-bit timer × 1
Timer 5 ..................Watchdog. Stable oscillation waiting function

 Serial interface
Synchronous type/Start-stop synchronous type × 1: Serial 0 (8-bit)
Serial 0...................Transfer direction of MSB/LSB selectable
Synchronous type/Remote control transmission/Simple remote control receive × 1: Serial 1 (8-bit)
Serial 1...................Transfer direction of MSB/LSB selectable. Start condition function
I2C × 1: Serial 2 (8-bit)
Serial 2...................Master transmission/reception. Slave transmission/reception

 OSD
OSD mode: Accommodation with menu (internal synchronous) or super impose (external synchronous) display
Applicable broadcasting system.....NTSC. PAL. PAL-M. PAL-N
Screen configuration ........24 characters × 2n rows (n = 1 to 6)
Character type .......Max. 512 character types (variable)
Character size ........12 dots × 18 dots (vertical direction: 1 dot for 2H at not enlargement)
Enlarged characters ......Each × 2, × 3 or × 4 settings in horizontal and vertical
Character interpolation....... None
Line background color .....8-hue settable (settable in the row unit at menu display)
Line background intensity..8 gradations settable in the row unit (at output of composite video signal)
Screen background color ...8-hue settable (at output of composite video signal)
Character color ......White (at output of composite video signal)
Character intensity .......8 gradations settable in the row unit (at output of composite video signal)
Frame function ......1-dot frame in 4 or 8 directions
Frame intensity ......4 gradations settable in the row unit (at output of composite video signal)
Box shade function ......Settable in the character unit (at output of composite video signal with 129 or more characters (character types))
Blinking .................None (covered by software)
Inverted character ..........Settable in the character unit
Halftone .................Settable in the row unit in 2 intensity gradations (at output of external synchronous composite video signal)

64 MAD00030KEM
 MN101D07G, MN101D07H, MN101DF07Z

CCD mode: Supports Closed Caption in the U.S.A.

Screen configuration ........32 characters × 16 rows
Character type .......Max. 128 character types (variable)
Character size ........2 dots × 26 dots (including 8 dots in the underlined area)
Enlarged characters ......None
Character interpolation .....None
Line background color .....8-hue settable
Line background intensity..8 gradations settable in the row unit (at output of composite video signal)
Screen background color ...8-hue settable (at output of composite video signal)
Character color ......8 colors (at RGB output). White (at output of composite video signal)
Character intensity .......8 gradations settable in the row unit (at output of composite video signal)
Frame function ......None
Box shade function ......None
Inverted character ........None
Halftone .................Settable in the row unit in 2 intensity gradations (at output of external synchronous composite video signal)
Others ....................Underline. Italic. Blinking function. Scroll
Common
Input ......................Composite video signal input (output level:1 V[p-p] / 2 V[p-p])
Clamp method .......Sync tip clamp. Clamp level in 4 levels
Output ....................Composite video output. Output of Y/C split video signal. Digital output (6 pins)
Measure against image fluctuation.....Built-in AFC circuit
Dot clock ...............1/2 of OSC oscillation clock (automatic phase adjustment)

 XDS
Built-in U.S. closed caption data slicer: Optional 2 line data can be extracted

 I/O Pins
I/O 85 : Common use: 71
Input 2 : Common use: 2

 A/D converter
8-bit × 14 channels (without S/H)

 PWM
13-bit × 2 channels (at repetition cycle 572 µs at 14.32 MHz)
10-bit × 2 channels (at repetition cycle 71.5 µs at 14.32 MHz)
8-bit × 1 channels (at repetition cycle 71.5 ms, 0.572 ms, 1.14 ms, 2.29 ms at 14.32 MHz)

 ICR
18-bit × 6 channels

 OCR
16-bit × 2: 8-bit synchronous output. 4-bit 3-state synchronous output
16-bit × 1: Weak electric field V-sync backup.
16-bit × 1: Rec CTL

 Special Ports
Buzzer output. 3-state output VLP pin. Remote control reception
CTL signal input terminal. Capstan FG inputterminal. Sylinder(Durm) PG/FG input terminals
HSW output terminal. Head Amp/Rortary control output terminals
Output of 1/2 OSC oscillation clock (2 V[p-p]). Output of 1/4 OSC oscillation clock (1 V[p-p])

 ROM Correction
Correcting address designation: Up to 3 addresses possible
Correction method: Correction program being saved in internal RAM

MAD00030KEM 65
 Electrical Charactreistics (Supply current)
Limit
Parameter Symbol Condition Unit
min typ max
IDD1 14.32 MHz oscillation without load. VDD = 5 V 60 100 mA
Operating supply current IDD2 1/1024 of 14.32 MHz operation without load. VDD = 3.0 V 2 5 mA
Stop of 14.32 MHz oscillation
IDD3 50 100 µA
32 kHz oscillation operation without load. VDD = 2.7 V
Supply current at STOP IDSP Stop of oscillation without load. VDD = 5 V. Ta = 55 °C 10 µA
IDHT0 14.32 MHz oscillation without load. VDD = 5 V 5 15 mA
Supply current at HALT Stop of 14.32 MHz oscillation
IDHT1 5 20 µA
32 kHz oscillation operation without load. VDD = 2.7 V
Ta = 25 °C±2 °C. VSS = 0 V

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Conversion relative error ∆NLAD ±3 LSB
A/D conversion time tAD fosc = 14.32 MHz 8 µs
Analog input voltage 5 V
Ta = 25 °C±2 °C. VDD = 5.0 V. VSS = 0 V

 Pin Assignment
LQFP112-P-2020

AFCLPG
FSCLPF
SECAM
SYOUT
RCTLN

SCOUT
RCTLP

PGMM
VOW1
VOW2
VOW3
VOW4
AVDD

VDD2
CTLA

VOB1
VOB2

AFCC
AVSS

SCIN
VRO

FSCI
AFG

YPG
YFG
FGF
VRI

PA6
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57

CO 85 56 SYIN
TPZ 86 55 CVIN2
AD13 87 54 CVIN
AD11 88 53 VSS2
AD10 89 52 CVOUT
AD9 90 51 P97
AD8 91 50 HSYNC
AD7 92 49 VSYNC
AD6 93 48 OSCO2
AD5 94 47 OSCI2
AD4 95 46 SXI
AD3 96 45 XO
AD2 97 44 XI
AD1 98 43 VSS
AD0 99 42 OSCI
VDD 100 41 OSCO
P77 101 40 VDD
P76 102 39 SBUFD0, PWM4
P75 103 38 PWM0
P74 104 37 PWM1
P73 105 36 P57
P72 106 35 SBUFD1
P71 107 34 SBUFD2
P70 108 33 SBUFD3
VSS 109 32 SBUFD4
ROTA 110 31 SBUFD5
HAMP 111 30 SBUFD6
DENV 112 29 SBUFD7
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
11
1
2
3
4
5
6
7
8
9

SBO1

SBO0
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
P56
P55
KEYIRQ4
KEYIRQ3
KEYIRQ2
KEYIRQ1
KEYIRQ0
SBT1
SBI1

P03
SBT0
SBI0

SDA
SCK
HBUFD6, BUZZER
HUBFD4
HUBFD2, DAOUT
HUBFD0
HSW
VLP
NRST

66 MAD00030KEM
67
 MN101D08 Series
Type MN101D08E MN101DF08G
Internal ROM type Mask ROM FLASH
ROM (byte) 80K 128K
RAM (byte) 2K 4K
Package (Lead-free) LQFP080-P-1414A
[When using main clock]
0.1397 µs (at 4.0 V to 5.5 V, 14.32 MHz) 0.1397 µs (at 4.0 V to 5.5 V, 14.32 MHz)
Minimum Instruction 71.5 µs (at 2.7 V to 5.5 V, 14.32 MHz internal 71.5 µs (at 2.7 V to 5.5 V, 14.32 MHz internal
Execution Time frequency division) frequency division)
[When using sub clock] 61 µs (at 2.5 V to 5.5 V, 32.768 kHz)
61 µs (at 2.5 V to 5.5 V, 32.768 kHz)

 Interrupts
RESET. Runaway. External 0 to 4. Timer 0 to 3. Timer 6. Capstan FG. Control. HSW. Cylinder(Drum) FG. Servo V-sync. Synchronous
output. OSD. XDS. Serial 1. Serial 2. PWM4. OSDV-sync

 Timer Counter
8-bit timer × 2
Timer 0 ..................Timer function
Timer 1 ..................Timer function. Linear timer counter function
16-bit timer × 3
Timer 2 ..................Timer function. Input capture (CTL specified edge). Duty judgment of CTL signal
Timer 3 ..................Timer function
Timer 6 ..................Clock function (max. 2 s)
19-bit timer × 1
Timer 5 ..................Watchdog. Stable oscillation waiting function

 Serial interface
Synchronous type × 1: Serial 1 (8-bit)
Serial 1...................Transfer direction of MSB/LSB selectable. Start condition function
I2C × 1: Serial 2 (8-bit)
Serial 2...................Master transmission/reception. Slave transmission/reception

 OSD
Display mode.........Accommodation with menu (internal synchronous) or super impose (external synchronous) display
Applicable broadcasting system.....NTSC. PAL. PAL-M. PAL-N
Screen configuration .......... 24 characters × 2n rows (n = 1 to 6)
Character type .......Max. 128 character types (variable, incude special characters)
Character size ........12 dots × 18 dots (vertical direction: 1 dot for 2H at not enlargement)
Enlarged characters .......Each × 2 settings in horizontal and vertical
Character interpolation....... None
Line background color ....... 8-hue settable (settable in the row unit at menu display)
Line background intensity.. 8 gradations (settable in the row unit)
Screen background color.... 8-hue (settable at menu display)
Character color ......White
Character intensity ........8 gradations (settable in the row unit)
Frame function ......1-dot frame in 4 directions
Frame intensity ......4 gradations (settable in the row unit)
Blinking .................None (covered by software)
Inverted character ..........Settable in the character unit
Halftone .................None
Input ......................Composite video signal input (output level:1 V[p-p] / 2 V[p-p])
Clamp method .......Sync tip clamp. Clamp level in 4 levels
Output ....................Composite video output
Measure against image fluctuation.....Built-in AFC circuit
Dot clock ...............1/2 of OSC oscillation clock (automatic phase adjustment)

 XDS
Built-in U.S. closed caption data slicer: Optional 1 line data can be extracted

68 MAD00032HEM
 MN101D08E, MN101DF08G

 I/O Pins
I/O 56 : Common use: 45
Input 1 : Common use: 1

 A/D converter
8-bit × 11 channels (without S/H)

 PWM
13-bit × 2 channels (at repetition cycle 572 µs at 14.32 MHz)
8-bit × 1 channels (at repetition cycle 71.5 ms, 0.572 ms, 1.14 ms, 2.29 ms at 14.32 MHz)

 ICR
16-bit × 2 channels (speed system)
18-bit × 4 channels (phase system)

 OCR
16-bit × 3: 8-bit synchronous output. 4-bit 3-state synchronous output. Rec CTL

 Special Ports
3-state output (PTO) VLP pin
CTL signal input terminal. Capstan FG inputterminal. Sylinder(Durm) PG/FG input terminals. Head Amp/Rortary control output
terminals.
Output of 1/4 OSC oscillation clock (1 V[p-p])

 ROM Correction
Correcting address designation: Up to 3 addresses possible
Correction method: Correction program being saved in internal RAM

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 14.32 MHz oscillation without load. VDD = 5 V 50 100 mA
Operating supply current IDD2 1/1024 of 14.32 MHz operation without load. VDD = 2.7 V 2 5 mA
Stop of 14.32 MHz oscillation
IDD3 50 100 µA
32 kHz oscillation operation without load. VDD = 2.7 V
Supply current at STOP IDSP Stop of oscillation without load. VDD = 5 V 10 µA
IDHT0 14.32 MHz oscillation without load. VDD = 5 V 5 15 mA
Supply current at HALT Stop of 14.32 MHz oscillation
IDHT1 5 20 µA
32 kHz oscillation operation without load. VDD = 2.7 V
Ta = 25 °C±2 °C. VSS = 0 V

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Conversion relative error ∆NLAD ±3 LSB
A/D conversion time tAD fosc = 14.32 MHz 8 µs
Analog input voltage 5 V
Ta = 25 °C±2 °C. VDD = 5.0 V. VSS = 0 V

MAD00032HEM 69
 Pin Assignment
LQFP080-P-1414A

AFCLPF
FSCLPF
RCTLN
RCTLP

CVIN2
AVDD

VDD2
CTLA

AFCC
AD10

AVSS

FSCI
AFG

YPG
YFG
AD9

VR0

FGF
VRI
C0
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
AD8 61 40 CVIN
AD7 62 39 VSS2
AD6 63 38 CVOUT
AD5 64 37 SXI
AD4 65 36 X0
AD3 66 35 XI
AD2 67 34 VSS
AD1 68 33 OSCI
AD0 69 32 OSC0
P77 70 31 VDD
P76 71 30 PWM4
P75 72 29 PWM0
P74 73 28 PWM1
P73 74 27 SBUFD1
P72 75 26 SBUFD2
P71 76 25 SBUFD3
P70 77 24 SBUFD4
ROTA 78 23 SBUFD5
HAMP 79 22 SBUFD6
DENV 80 21 SBUFD7
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
NSBT1
NSBI1
NSB01
P02
P01
P00
SDA
SCK
HBUFD6
HBUFD4
HBUFD2
HBUFD0
HSW
VLP
NRST

70 MAD00032HEM
71
 MN101D09 Series
Type MN101D09E MN101DF09G
Internal ROM type Mask ROM FLASH
ROM (byte) 80K 128K
RAM (byte) 2K 4K
Package (Lead-free) QFP100-P-1818B
[When using main clock]
0.1397 µs (at 4.0 V to 5.5 V, 14.32 MHz) 0.1397 µs (at 4.0 V to 5.5 V, 14.32 MHz)
Minimum Instruction 71.5 µs (at 2.7 V to 5.5 V, 14.32 MHz internal 71.5 µs (at 2.7 V to 5.5 V, 14.32 MHz internal
Execution Time frequency division) frequency division)
[When using sub clock] 61 µs (at 2.5 V to 5.5 V, 32.768 kHz)
61 µs (at 2.5 V to 5.5 V, 32.768 kHz)

 Interrupts
RESET. Runaway. External 0 to 4. Timer 0 to 3. Timer 6. Capstan FG. Control. HSW. Cylinder(Drum) FG. Servo V-sync. Synchronous
output. OSD. XDS. Serial 1. Serial 2. PWM4. OSDV-sync

 Timer Counter
8-bit timer × 2
Timer 0 ..................Timer function
Timer 1 ..................Timer function. Linear timer counter function
16-bit timer × 3
Timer 2 ..................Timer function. Input capture (CTL specified edge). Duty judgment of CTL signal
Timer 3 ..................Timer function
Timer 6 ..................Clock function (max. 2 s)
19-bit timer × 1
Timer 5 ..................Watchdog. Stable oscillation waiting function

 Serial interface
Synchronous type × 1: Serial 1 (8-bit)
Serial 1...................Transfer direction of MSB/LSB selectable. Start condition function
I2C × 1: Serial 2 (8-bit)
Serial 2...................Master transmission/reception. Slave transmission/reception

 OSD
Display mode.........Accommodation with menu (internal synchronous) or super impose (external synchronous) display
Applicable broadcasting system.....NTSC. PAL. PAL-M. PAL-N
Screen configuration .......... 24 characters × 2n rows (n = 1 to 6)
Character type .......Max. 128 character types (variable, incude special characters)
Character size ........12 dots × 18 dots (vertical direction: 1 dot for 2H at not enlargement)
Enlarged characters .......Each × 2 settings in horizontal and vertical
Character interpolation....... None
Line background color ....... 8-hue settable (settable in the row unit at menu display)
Line background intensity.. 8 gradations (settable in the row unit)
Screen background color.... 8-hue (settable at menu display)
Character color ......White
Character intensity .......8 gradations (settable in the row unit)
Frame function ......1-dot frame in 4 directions
Frame intensity ......4 gradations (settable in the row unit)
Blinking .................None (covered by software)
Inverted character ..........Settable in the character unit
Halftone .................None
Input ......................Composite video signal input (output level:1 V[p-p] / 2 V[p-p])
Clamp method .......Sync tip clamp. Clamp level in 4 levels
Output ....................Composite video output
Measure against image fluctuation.....Built-in AFC circuit
Dot clock ...............1/2 of OSC oscillation clock (automatic phase adjustment)

 XDS
Built-in U.S. closed caption data slicer: Optional 2 line data can be extracted

72 MAD00033HEM
 MN101D09E, MN101DF09G

 I/O Pins
I/O 56 : Common use: 45
Input 1 : Common use: 1

 A/D converter
8-bit × 11 channels (without S/H)

 PWM
13-bit × 2 channels (at repetition cycle 572 µs at 14.32 MHz)
8-bit × 1 channels (at repetition cycle 71.5 ms, 0.572 ms, 1.14 ms, 2.29 ms at 14.32 MHz)

 ICR
16-bit × 2 channels (speed system)
18-bit × 4 channels (phase system)

 OCR
16-bit × 3: 8-bit synchronous output. 4-bit 3-state synchronous output. Rec CTL

 Special Ports
3-state output (PTO) VLP pin
CTL signal input terminal. Capstan FG inputterminal. Sylinder(Durm) PG/FG input terminals
HSW output terminal. Head Amp/Rortary control output terminals
Output of 1/4 OSC oscillation clock (1 V[p-p])

 ROM Correction
Correcting address designation: Up to 3 addresses possible
Correction method: Correction program being saved in internal RAM

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 14.32 MHz oscillation without load. VDD = 5 V 50 100 mA
Operating supply current IDD2 1/1024 of 14.32 MHz operation without load. VDD = 2.7 V 2 5 mA
Stop of 14.32 MHz oscillation
IDD3 50 100 µA
32 kHz oscillation operation without load. VDD = 2.7 V
Supply current at STOP IDSP Stop of oscillation without load. VDD = 5 V 10 µA
IDHT0 14.32 MHz oscillation without load. VDD = 5 V 5 15 mA
Supply current at HALT Stop of 14.32 MHz oscillation
IDHT1 5 20 µA
32 kHz oscillation operation without load. VDD = 2.7 V
Ta = 25 °C±2 °C. VSS = 0 V

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Conversion relative error ∆NLAD ±3 LSB
A/D conversion time tAD fosc = 14.32 MHz 8 µs
Analog input voltage 5 V
Ta = 25 °C±2 °C. VDD = 5.0 V. VSS = 0 V

MAD00033HEM 73
 Pin Assignment
QFP100-P-1818B

AFCLPF
FSCLPF
RCTLN
RCTLP
AVDD

VDD2
CTLA

AFCC
AVSS

VRO

FSCI
AFG

YPG
YFG
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
FGF
VRI
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
CO 76 50 CVIN2
N.C. 77 49 CVIN
N.C. 78 48 VSS2
AD10 79 47 CVOUT
AD9 80 46 N.C.
AD8 81 45 N.C.
AD7 82 44 N.C.
AD6 83 43 N.C.
AD5 84 42 SXI
AD4 85 41 XO
AD3 86 40 XI
AD2 87 39 VSS
AD1 88 38 OSCI
AD0 89 37 OSCO
P77 90 36 VDD
P76 91 35 PWM4
P75 92 34 PWM0
P74 93 33 PWM1
P73 94 32 SBUFD1
P72 95 31 SBUFD2
P71 96 30 SBUFD3
P70 97 29 SBUFD4
ROTA 98 28 SBUFD5
HAMP 99 27 SBUFD6
DENV 100 26 SBUFD7
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
N.C.
N.C.
N.C.
N.C.
N.C.
NSBT1
NSBI1
NSBO1
P02
P01
P00
SDA
SCK
HBUFD6
HBUFD4
HBUFD2
HBUFD0
HSW
VLP
NRST

74 MAD00033HEM
75
 MN101D10 Series
Type MN101D10F MN101D10G MN101DF10G
Internal ROM type Mask ROM FLASH
ROM (byte) 96K 128K
RAM (byte) 2.5K 3.5K 4K
Package (Lead-free) QFP100-P-1818B
0.1397 µs (at 4.0 V to 5.5 V, 14.32
[When using main clock] MHz)
0.1397 µs (at 4.0 V to 5.5 V, 14.32 MHz)
Minimum Instruction 71.5 µs (at 2.7 V to 5.5 V, 14.32
71.5 µs (at 2.7 V to 5.5 V, 14.32 MHz internal frequency division)
Execution Time MHz internal frequency division)
[When using sub clock] 61 µs (at 2.5 V to 5.5 V, 32.768
61 µs (at 2.5 V to 5.5 V, 32.768 kHz) kHz)

 Interrupts
RESET. Runaway. External 0 to 4. Timer 0 to 3. Timer 6. Capstan FG. Control. HSW. Cylinder(Drum) FG. Servo V-sync. Synchronous
output. OSD. XDS. Serial 0. Serial 1. Serial 2. PWM4. OSDV-sync

 Timer Counter
8-bit timer × 2
Timer 0 ..................Timer function
Timer 1 ..................Timer function. Linear timer counter function
16-bit timer × 3
Timer 2 ..................Timer function. Input capture. Duty judgment of CTL signal (VISS/VASS detection function). Generation of
remote control output carrier frequency
Timer 3 ..................Timer function. Generation of serial 1 transmission clock
Timer 6 ..................Clock function (max. 2 s)
19-bit timer × 1
Timer 5 ..................Watchdog. Stable oscillation waiting function

 Serial interface
Synchronous type × 1: Serial 0 (8-bit)
Serial 0...................Transfer direction of MSB/LSB selectable. Start condition function
Synchronous type/Remote control transmission: Serial 1 (8-bit)
Serial 1...................Transfer direction of MSB/LSB selectable. Start condition function
I2C × 1: Serial 2 (8-bit)
Serial 2...................Master transmission/reception. Slave transmission/reception

 OSD
Display mode.........Accommodation with menu (internal synchronous) or super impose (external synchronous) display
Applicable broadcasting system.....NTSC. PAL. PAL-M. PAL-N
Screen configuration .......... 24 characters × 2n rows (n = 1 to 6)
Character type .......Max. 256 character types (variable, incude special characters)
Character size ........12 dots × 18 dots (vertical direction: 1 dot for 2H at not enlargement)
Enlarged characters .......Each × 2 settings in horizontal and vertical
Character interpolation....... None
Line background color ....... 8-hue settable (settable in the row unit at menu display)
Line background intensity.. 8 gradations (settable in the row unit)
Screen background color.... 8-hue (settable at menu display)
Character color ......White
Character intensity ........8 gradations (settable in the row unit)
Frame function ......1-dot frame in 8 directions
Frame intensity ......4 gradations (settable in the row unit)
Blinking .................None (covered by software)
Inverted character ..........Settable in the character unit
Halftone .................None
Input ......................Composite video signal input (output level:1 V[p-p] / 2 V[p-p])
Clamp method .......Sync tip clamp. Clamp level in 4 levels
Output ....................Composite video output
Measure against image fluctuation.....Built-in AFC circuit
Dot clock ...............1/2 of OSC oscillation clock (automatic phase adjustment)
MESECAM compatibility . Subcarrier leak function for superimpose display

76 MAD00043FEM
 MN101D10F, MN101D10G, MN101DF10G

 XDS
Built-in U.S. closed caption data slicer: Optional 1 line data can be extracted

 I/O Pins
I/O 76 : Common use: 56
Input 1 : Common use: 1

 A/D converter
8-bit × 12 channels (without S/H)

 PWM
13-bit × 2 channels (at repetition cycle 572 µs at 14.32 MHz)
8-bit × 1 channels (at repetition cycle 71.5 ms, 0.572 ms, 1.14 ms, 2.29 ms at 14.32 MHz)

 ICR
16-bit × 2 channels (speed system)
18-bit × 4 channels (phase system)

 OCR
16-bit × 3: 8-bit synchronous output. 4-bit 3-state synchronous output. Rec CTL

 Special Ports
3-state output (PTO) VLP pin
CTL signal input terminal. Capstan FG inputterminal. Sylinder(Durm) PG/FG input terminals
HSW output terminal. Head Amp/Rortary control output terminals
Output of 1/4 OSC oscillation clock (1 V[p-p])

 ROM Correction
Correcting address designation: Up to 3 addresses possible
Correction method: Correction program being saved in internal RAM

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 14.32 MHz oscillation without load. VDD = 5 V 50 100 mA
Operating supply current IDD2 1/1024 of 14.32 MHz operation without load. VDD = 2.7 V 2 5 mA
Stop of 14.32 MHz oscillation
IDD3 32 kHz oscillation operation without load. VDD = 2.7 V 50 100 µA
Supply current at STOP IDSP Stop of oscillation without load. VDD = 5 V. Ta = 55 °C 10 µA
IDHT0 14.32 MHz oscillation without load. VDD = 5 V 5 15 mA
Supply current at HALT Stop of 14.32 MHz oscillation
IDHT1 5 20 µA
32 kHz oscillation operation without load. VDD = 2.7 V
Ta = 25 °C±2 °C. VSS = 0 V

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Conversion relative error ∆NLAD ±3 LSB
A/D conversion time tAD fosc = 14.32 MHz 8 µs
Analog input voltage 5 V
Ta = 25 °C±2 °C. VDD = 5.0 V. VSS = 0 V

MAD00043FEM 77
 Pin Assignment
QFP100-P-1818B

AFCLPF
FSCLPF
SECAM
RCTLN
RCTLP
AVDD

VDD2
CTLA

AFCC
AVSS

VRO

FSCI
AFG

YPG
YFG
FGF
VRI

PA0
PA1
PA2
PA3
PA4
PA5
PA6
P92
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
CO 76 50 CVIN2
P90 77 49 CVIN
AD11 78 48 VSS2
AD10 79 47 CVOUT
AD9 80 46 PB7
AD8 81 45 P20
AD7 82 44 P21
AD6 83 43 P22
AD5 84 42 SXI
AD4 85 41 XO
AD3 86 40 XI
AD2 87 39 VSS
AD1 88 38 OSCI
AD0 89 37 OSCO
P77 90 36 VDD
P76 91 35 SBUFD0
P75 92 34 PWM0
P74 93 33 PWM1
P73 94 32 SBUFD1
P72 95 31 SBUFD2
P71 96 30 SBUFD3
P70 97 29 SBUFD4
ROTA 98 28 SBUFD5
HAMP 99 27 SBUFD6
DENV 100 26 SBUFD7
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
P54
P53
P52
P51
NSDO
NSBT1
NSBI1
NSBO1
NSBT0
NSBI0
NSBO0
SDA
SCK
HBUFD6
HBUFD4
HBUFD2
HBUFD0
HSW
VLP
NRST

78 MAD00043FEM
79
 MN101C87 Series
Type MN101C87A MN101C87D MN101CF87G
Internal ROM type Mask ROM FLASH
ROM (byte) 32K 64K 128K
RAM (byte) 1.5K 2K 4K
Package (Lead-free) LQFP064-P-1414
0.1 µs (at 4.5 V to 5.5 V, 20 MHz)
0.24 µs (at 2.7 V to 5.5 V, 8.4 MHz)
Minimum Instruction 0.48 µs (at 2.3 V to 5.5 V, 4.19 MHz)*
Execution Time 1.0 µs (at 2.0 V to 5.5 V, 2.0 MHz)*
62.5 µs (at 2.0 V to 5.5 V, 32 kHz)*
*: The lower limit for operation guarantee for flash memory built-in type is 2.5 V.

 Interrupts
RESET. Watchdog. External 0 to 4. Timer 0 to 3. Timer 6. Timer 7 (2 systems). Time base. Serial 0 (2 systems). Serial 2. A/D conversion
finish. Automatic transfer finish. FL display key scan. FL display dimmer

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement
Timer 1 ..................Square-wave output. Event count. Serial transfer clock output
Timer 2 ..................Square-wave/8-bit PWM output. Serial transfer clock output. Event count. Simple pulse width measurement
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial transfer clock output
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Pulse width measurement.
Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0
Synchronous type/Single-master I2C × 1: Serial 2

 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 26 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
High Voltage 26 : Output: 18. I/O: 8. P-ch. open drain (breakdown voltage –40 V). FL drive: 26. Specified pull-down resistor mask
option: 16

 A/D converter
10-bit × 8 channels (with S/H)

 Display control function

FL: (8 to 16) segments × (18 to 10) digits
16 levels dimmer function
Light-and-dark 2-tones display function
Can support automatic display to universal grid display tubes
Output dimmer waveform for FL driver connection (DROUT)
Internal pull down resister is available between Port 6 and Vpp, Port 8 and Vpp by Mask option (only for Mask ROM version)
Internal pull down resister between Port 4 and Vpp, Port 7 and Vpp

80 MAD00050HEM
 MN101C87A, MN101C87D, MN101CF87G

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 3 addresses possible (for MN101C87D)

 Pin Assignment
LQFP064-P-1414

P70, SEG7, DGT0

P71, SEG6, DGT1
P72, SEG5, DGT2
P73, SEG4, DGT3
P74, SEG3, DGT4
P75, SEG2, DGT5
P76, SEG1, DGT6
P77, SEG0, DGT7

P60, DGT10

P62, DGT12
P63, DGT13
P64, DGT14
P65, DGT15
P61, DGT11
P40, DGT8
P41, DGT9
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
P87, SEG8 49 32 DGT16, P66
P86, SEG9 50 31 DGT17, P67
P85, SEG10 51 30 VDD3
P84, SEG11 52 29 VDD2
P83, SEG12 53 28 LED2, P52
P82, SEG13 54 27 LED1, P51
P81, SEG14 55 26 LED0, P50
P80, SEG15 56 25 IRQ4, P24
VPP 57 24 IRQ3, P23
P00, SBO0, TXD 58 23 IRQ2, P22
P01, SBI0, RXD 59 22 ACZ, IRQ1, P21
P02, SBT0 60 21 IRQ0, P20
P03, SBO2, SDA 61 20 TM7IO, P14
P04, SBI2, AN7 62 19 DROUT, TM3IO, P13
P05, SBT2, SCL 63 18 TM2IO, P12
P06, BUZZER, AN6 64 17 TM1IO, P11
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9
VDD1
VREF+

OSC2
OSC1
VSS
XI
XO
MMOD
NRST, P27
RMOUT, TM0IO, P10
AN5, PA5
AN4, PA4
AN3, PA3
AN2, PA2
AN1, PA1
AN0, PA0

MAD00050HEM 81
 MN101C88 Series
Type MN101C88D MN101C88G MN101CF88G
Internal ROM type Mask ROM FLASH
ROM (byte) 64K 128K
RAM (byte) 2K 4K 10K
Package (Lead-free) QFP100-P-1818B
0.1 µs (at 4.5 V to 5.5 V, 20 MHz)
0.24 µs (at 2.7 V to 5.5 V, 8.4 MHz)
Minimum Instruction 0.48 µs (at 2.3 V to 5.5 V, 4.19 MHz)*
Execution Time 1.0 µs (at 2.0 V to 5.5 V, 2.0 MHz)*
62.5 µs (at 2.0 V to 5.5 V, 32 kHz)*
*: The lower limit for operation guarantee for flash memory built-in type is 2.5 V.

 Interrupts
RESET. Watchdog. External 0 to 4. Timer 0 to 3. Timer 6. Timer 7 (2 systems). Time base. Serial 0 (2 systems). Serial 1 (2 systems).
Serial 2. A/D conversion finish. Automatic transfer finish. FL display key scan. FL display dimmer

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement
Timer 1 ..................Square-wave output. Event count. Serial transfer clock output
Timer 2 ..................Square-wave/8-bit PWM output. Serial transfer clock output. Event count. Simple pulse width measurement
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial transfer clock output
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Pulse width measurement.
Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Single-master I2C × 1: Serial 2

 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 35 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
High Voltage 53 : Output: 29. I/O: 24. P-ch. open drain (breakdown voltage –40 V): FL drive: 53. Specified pull-down resistor mask
option: 35

 A/D converter
10-bit × 8 channels (with S/H)

 Display control function

FL: (35 to 43) segments × (18 to 10) digits
16 levels dimmer function
Light-and-dark 2-tones display function
Can support automatic display to universal grid display tubes
Output dimmer waveform for FL driver connection (DROUT)
Internal pull down resister is available between Port 6 and Vpp, Port 9 and Vpp, Port B and Vpp, Port C and Vpp, Port D and Vpp by
Mask option (only for Mask ROM version)
Internal pull down resister between Port 4 and Vpp, Port 7 and Vpp, Port 8 and Vpp

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

82 MAD00051JEM
 MN101C88D, MN101C88G, MN101CF88G

 ROM Correction
Correcting address designation: Up to 3 addresses possible

 Pin Assignment
QFP100-P-1818B

P70, SEG7, DGT0

P71, SEG6, DGT1
P72, SEG5, DGT2
P73, SEG4, DGT3
PB6, SEG28
PB7, SEG27
PC0, SEG26
PC1, SEG25
PC2, SEG24
P90, SEG23
P91, SEG22
P92, SEG21
P93, SEG20
P94, SEG19
P95, SEG18
P96, SEG17
P97, SEG16
P80, SEG15
P81, SEG14
P82, SEG13
P83, SEG12

P85, SEG10
P84, SEG11

P86, SEG9
P87, SEG8
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
PB5, SEG29 76 50 DGT4, SEG3, P74
PB4, SEG30 77 49 DGT5, SEG2, P75
PB3, SEG31 78 48 DGT6, SEG1, P76
PB2, SEG32 79 47 DGT7, SEG0, P77
PB1, SEG33 80 46 DGT8, P40
PB0, SEG34 81 45 DGT9, P41
PD7, SEG35 82 44 DGT10, P60
PD6, SEG36 83 43 DGT11, P61
PD5, SEG37 84 42 DGT12, P62
PD4, SEG38 85 41 DGT13, P63
PD3, SEG39 86 40 DGT14, P64
PD2, SEG40 87 39 DGT15, P65
PD1, SEG41 88 38 DGT16, P66
PD0, SEG42 89 37 DGT17, P67
VPP 90 36 VDD3
P50, LED0, SBO0B, TXD0B 91 35 VDD2
P51, LED1, SBI0B, RXD0B 92 34 P34
P52, LED2, SBT0B 93 33 P33
P10, TM0IO, RMOUT 94 32 SCL, SBT2, P32
P11, TM1IO 95 31 SBI2, P31
P12, TM2IO 96 30 SDA, SBO2, P30
P13, TM3IO 97 29 IRQ4, P24
P14 98 28 IRQ3, P23
P15, TM7IO 99 27 IRQ2, P22
P16, DROUT 100 26 ACZ, IRQ1, P21
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9 VDD1
TXD0A, SBO0A, P00
RXD0A, SBI0A, P01
SBT0A, P02
TXD1, SBO1, P03
RXD1, SBI1, P04
SBT1, P05
BUZZER, P06

OSC2
OSC1
VSS
XI
XO
MMOD

VREF+
IRQ0, P20
NRST, P27

AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6
AN7, PA7

MAD00051JEM 83
 MN101CA3 Series
Type MN101CA3F MN101CFA3G
Internal ROM type Mask ROM FLASH
ROM (byte) 96K 128K
RAM (byte) 4K 10K
Package (Lead-free) QFP100-P-1818B
0.1 µs (at 4.5 V to 5.5 V, 20 MHz)
0.24 µs (at 2.7 V to 5.5 V, 8.4 MHz)
Minimum Instruction 0.48 µs (at 2.3 V to 5.5 V, 4.19 MHz)*
Execution Time 1.0 µs (at 2.0 V to 5.5 V, 2.0 MHz)*
62.5 µs (at 2.0 V to 5.5 V, 32 kHz)*
*: The lower limit for operation guarantee for flash memory built-in type is 2.5 V.

 Interrupts
RESET. Watchdog. External 0 to 6. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Time base. Serial 0 (2 systems).
Serial 1 (2 systems). Serial 2. Serial 3 (2 systems). A/D conversion finish. Automatic transfer finish. FL display key scan. FL display
dimmer

 Timer Counter
8-bit timer × 6
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement
Timer 1 ..................Square-wave output. Event count. Serial transfer clock output
Timer 2, 4 ..............Square-wave/8-bit PWM output. Serial transfer clock output. Event count. Simple pulse width measurement
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial transfer clock output
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7, 8 ..............Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Pulse width measurement.
Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Single-master I2C × 1: Serial 2
UART (full-duplex) × 1: Serial 3

 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 36 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
High Voltage 53 : Output: 26. I/O: 27. P-ch. open drain (breakdown voltage –40 V): FL drive: 53. Specified pull-down resistor mask
option: 35

 A/D converter
8-bit × 8 channels (with S/H)

 Display control function

FL: (35 to 43) segments × (18 to 10) digits
16 levels dimmer function
Light-and-dark 2-tones display function
Can support automatic display to universal grid display tubes
Output dimmer waveform for FL driver connection (DROUT)
Internal pull down resister is available between Port 6 and Vpp, Port 9 and Vpp, Port B and Vpp, Port C and Vpp, Port D and Vpp by
Mask option (only for Mask ROM version)
Internal pull down resister between Port 4 and Vpp, Port 7 and Vpp, Port 8 and Vpp

84 MAD00068DEM
 MN101CA3F, MN101CFA3G

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 3 addresses possible

 Pin Assignment
QFP100-P-1818B

P70, SEG7, DGT0

P71, SEG6, DGT1
P72, SEG5, DGT2
P73, SEG4, DGT3
PB6, SEG28
PB7, SEG27
PC0, SEG26
PC1, SEG25
PC2, SEG24
P90, SEG23
P91, SEG22
P92, SEG21
P93, SEG20
P94, SEG19
P95, SEG18
P96, SEG17
P97, SEG16
P80, SEG15
P81, SEG14
P82, SEG13
P83, SEG12

P85, SEG10
P84, SEG11

P86, SEG9
P87, SEG8
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
PB5, SEG29 76 50 DGT4, SEG3, P74
PB4, SEG30 77 49 DGT5, SEG2, P75
PB3, SEG31 78 48 DGT6, SEG1, P76
PB2, SEG32 79 47 DGT7, SEG0, P77
PB1, SEG33 80 46 DGT8, P40
PB0, SEG34 81 45 DGT9, P41
PD7, SEG35 82 44 DGT10, P60
PD6, SEG36 83 43 DGT11, P61
PD5, SEG37 84 42 DGT12, P62
PD4, SEG38 85 41 DGT13, P63
PD3, SEG39 86 40 DGT14, P64
PD2, SEG40 87 39 DGT15, P65
PD1, SEG41 88 38 DGT16, P66
PD0, SEG42 89 37 DGT17, P67
VPP 90 36 VDD3
P50, LED0, SBO0B, TXD0B 91 35 VDD2
P51, LED1, SBI0B, RXD0B 92 34 RXD3, P34
P52, LED2, SBT0B 93 33 TXD3, P33
P10, TM0IO, RMOUT 94 32 SCL, SBT2, P32
P11, TM1IO 95 31 SBI2, P31
P12, TM2IO 96 30 SDA, SBO2, P30
P13, TM3IO 97 29 IRQ4, P24
P14, TM4IO 98 28 IRQ3, P23
P15, TM7IO 99 27 IRQ2, P22
P16, DROUT, SSTART 100 26 ACZ, IRQ1, P21
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9 VDD1
TXD0A, SBO0A, P00
RXD0A, SBI0A, P01
SBT0A, P02
TXD1, SBO1, P03
RXD1, SBI1, P04
SBT1, P05
BUZZER, P06

OSC2
OSC1
VSS
XI
XO
MMOD

TM8IO, P17
IRQ0, P20
NRST, P27

AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
IRQ5, AN6, PA6
IRQ6, AN7, PA7

MAD00068DEM 85
 MN101C38 Series
Type MN101C38A MN101C38C MN101CP38C
Internal ROM type Mask ROM EPROM
ROM (byte) 32K 48K
RAM (byte) 1.5K 2K
Package (Lead-free) LQFP100-P-1414, QFP100-P-1818B
0.1 µs (at 4.5 V to 5.5 V, 20 MHz)
Minimum Instruction 0.25 µs (at 2.7 V to 5.5 V, 8 MHz)
Execution Time 125 µs (at 2.0 V to 5.5 V, 32 kHz)*
*: The lower limit for operation guarantee for EPROM built-in type is 2.3 V.

 Interrupts
RESET. Watchdog. External 0 to 4. Timer 2 to 5. Time base. Serial 0. Serial 1. A/D conversion finish

 Timer Counter
8-bit timer × 2
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 4 ..................Square-wave/16-bit PWM output. Event count. Synchronous output event. Input capture
Time base timer: One-minute count setting. Independently operable 8-bit timer 5
Watchdog timer × 1

 Serial interface
Synchronous type/Simple UART (half-duplex) × 1: Serial 0
Synchronous type × 1: Serial 1

 I/O Pins
I/O 44 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit). Specified pull-down resistor
partially selectable
Input 13 : Common use. Specified pull-up resistor available. Specified pull-down resistor partially selectable

 A/D converter
10-bit × 8 channels (with S/H)

 Display control function

LCD: 52 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 8 MHz. VDD = 5 V 10 25 mA
Operating supply current
IDD2 fx = 32 kHz. VDD = 3 V 30 100 µA
IDD3 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 8 µA
Supply current at HALT
IDD4 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 24 µA
VDD = 5 V. Ta = 25 °C 1 µA
Supply current at STOP IDD5
VDD = 5 V. Ta = -40 °C to +85 °C 20 µA

86 MAD00018HEM
MAD00018HEM
 Pin Assignment

SEG11

SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24

99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
QFP100-P-1818B, LQFP100-P-1414

100
COM3 1 75 SEG25
COM2 2 74 SEG26, P80, D0
COM1 3 73 SEG27, P81, D1
COM0 4 72 SEG28, P82, D2
VLC3 5 71 SEG29, P83, D3
VLC2 6 70 SEG30, P84, D4
VLC1 7 69 SEG31, P85, D5
VDD 8 68 SEG32, P86, D6
OSC2 9 67 SEG33, P87, D7
OSC1 10 66 SEG34, P77, A15
VSS 11 65 SEG35, P76, A14
XI 12 64 SEG36, P75, A13
XO 13 63 SEG37, P74, A12
MMOD 14 62 SEG38, P73, A11
VREF- 15 61 SEG39, P72, A10
KEY0, AN0, PA0 16 60 SEG40, P71, A9
KEY1, AN1, PA1 17 59 SEG41, P70, A8
KEY2, AN2, PA2 18 58 SEG42, P67, A7
KEY3, AN3, PA3 19 57 SEG43, P66, A6
KEY4, AN4, PA4 20 56 SEG44, P65, A5
KEY5, AN5, PA5 21 55 SEG45, P64, A4
KEY6, AN6, PA6 22 54 SEG46, P63, A3
KEY7, AN7, PA7 23 53 SEG47, P62, A2
VREF+ 24 52 SEG48, P61, A1
TXD, SBO0, P00 25 51 SEG49, P60, A0
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

P11
P30
P31
P32

SBI1, P04
IRQ0, P20
IRQ2, P22
IRQ3, P23
IRQ4, P24

SBT0, P02
SBT1, P05

SBO1, P03
NRST, P27
TM2IO, P12
TM3IO, P13
TM4IO, P14

RMOUT, P10
LED2, /CS, P52
LED1, /RE, P51

RXD, SBI0, P01

LED0, /WE, P50

SENS, IRQ1, P21

NDK, BUZZER, P06

LED3, SEG51, A16, P53
LED4, SEG50, A17, P54
MN101C38A, MN101C38C, MN101CP38C

87
 MN101C39 Series
Type MN101C39C MN101CP39C
Internal ROM type Mask ROM EPROM
ROM (byte) 48K
RAM (byte) 2K
Package (Lead-free) TQFP080-P-1212D
0.1 µs (at 4.5 V to 5.5 V, 20 MHz)
Minimum Instruction 0.25 µs (at 2.7 V to 5.5 V, 8 MHz)
Execution Time 125 µs (at 2.0 V to 5.5 V, 32 kHz)*
*: The lower limit for operation guarantee for EPROM built-in type is 2.3 V.

 Interrupts
RESET. Watchdog. External 0 to 4. Timer 2 to 5. Time base. Serial 0. Serial 1. A/D conversion finish

 Timer Counter
8-bit timer × 2
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 4 ..................Square-wave/16-bit PWM output. Event count. Synchronous output event. Input capture
Time base timer: One-minute count setting. Independently operable 8-bit timer 5
Watchdog timer × 1

 Serial interface
Synchronous type/Simple UART (half-duplex) × 1: Serial 0
Synchronous type × 1: Serial 1

 I/O Pins
I/O 49 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit). Specified pull-down resistor
partially selectable
Input 12 : Common use. Specified pull-up resistor available. Specified pull-down resistor partially selectable

 A/D converter
10-bit × 8 channels (with S/H)

 Display control function

LCD: 28 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 8 MHz. VDD = 5 V 8 25 mA
Operating supply current
IDD2 fx = 32 kHz. VDD = 3 V 18 100 µA
IDD3 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 3 8 µA
Supply current at HALT
IDD4 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 25 µA
VDD = 5 V. Ta = 25 °C 1 µA
Supply current at STOP IDD5
VDD = 5 V. Ta = -40 °C to +85 °C 20 µA

88 MAD00015JEM
 MN101C39C, MN101CP39C

 Pin Assignment
TQFP080-P-1212D

P54, SEG26, LED4, A17

P53, SEG27, LED3, A16

P50, LED0, NWE

P51, LED1, NRE
P52, LED2, NCS
P65, SEG20, A5
P64, SEG21, A4
P63, SEG22, A3
P62, SEG23, A2
P61, SEG24, A1
P60, SEG25, A0

P47, KEY7
P46, KEY6
P45, KEY5
P44, KEY4
P43, KEY3
P42, KEY2
P41, KEY1
P40, KEY0
P23, IRQ3
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
P66, SEG19, A6 61 40 IRQ2, P22
P67, SEG18, A7 62 39 SENS, IRQ1, P21
P70, SEG17, A8 63 38 IRQ0, P20
P71, SEG16, A9 64 37 TM4IO, P14
P72, SEG15, A10 65 36 TM3IO, P13
P73, SEG14, A11 66 35 TM2IO, P12
P74, SEG13, A12 67 34 P11
P75, SEG12, A13 68 33 RMOUT, P10
P76, SEG11, A14 69 32 NRST, P27
P77, SEG10, A15 70 31 NDK, BUZZER, P06
P87, SEG9, D7 71 30 SBT1, P05
P86, SEG8, D6 72 29 SBI1, P04
P85, SEG7, D5 73 28 SBO1, P03
P84, SEG6, D4 74 27 SBT0, P02
P83, SEG5, D3 75 26 RXD, SBI0, P01
P82, SEG4, D2 76 25 TXD, SBO0, P00
P81, SEG3, D1 77 24 VREF+
P80, SEG2, D0 78 23 AN7, PA7
SEG1 79 22 AN6, PA6
SEG0 80 21 AN5, PA5
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9
COM3
COM2
COM1
COM0
VLC3
VLC2
VLC1
VDD
OSC2
OSC1
VSS
XI
XO
MMOD
VREF-
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4

MAD00015JEM 89
 MN101C48 Series
Type MN101C485 MN101C487 MN101CP487
Internal ROM type Mask ROM EPROM
ROM (byte) 8K 16K
RAM (byte) 0.5K
Package (Lead-free) LQFP064-P-1414, TQFP064-P-1010B
0.10 µs (at 4.5 V to 5.5 V, 20 MHz)
Minimum Instruction 0.25 µs (at 2.7 V to 5.5 V, 8 MHz)
Execution Time 125 µs (at 2.0 V to 5.5 V, 32 kHz)*
*: The lower limit for operation guarantee for EPROM built-in type is 2.3 V.

 Interrupts
RESET. Watchdog. External 0 to 2. External 4. Timer 2 to 5. Time base. Serial 0. A/D conversion finish

 Timer Counter
8-bit timer × 2
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 4
Time base timer: One-minute count setting. Independently operable 8-bit timer 5
Watchdog timer × 1

 Serial interface
Synchronous type/Simple UART (half-duplex) × 1: Serial 0

 I/O Pins
I/O 36 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit). Specified pull-down resistor
partially selectable
Input 11 : Common use. Specified pull-up resistor available. Specified pull-down resistor partially selectable

 A/D converter
10-bit × 8 channels (with S/H)

 Display control function

LCD: 25 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 8 MHz. VDD = 5 V 10 25 mA
Operating supply current
IDD2 fx = 32 kHz. VDD = 3 V 15 100 µA
IDD3 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 4 8 µA
Supply current at HALT
IDD4 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 30 µA
VDD = 5 V. Ta = 25 °C 1 µA
Supply current at STOP IDD5
VDD = 5 V. Ta = -40 °C to +85 °C 25 µA

90 MAD00012HEM
 MN101C485, MN101C487, MN101CP487

 Pin Assignment
LQFP064-P-1414, TQFP064-P-1010B

SEG24, P53, LED3, A16

P21, IRQ1, SENS

P50, /WE, LED1
SEG16, P67, A7
SEG17, P66, A6
SEG18, P65, A5
SEG19, P64, A4
SEG20, P63, A3
SEG21, P62, A2
SEG22, P61, A1
SEG23, P60, A0

P51, /RE, LED1

P52, /CS, LED2

P14, TM4IO
P22, IRQ2

P20, IRQ0
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
A8, P70, SEG15 49 32 P13, TM3IO
A9, P71, SEG14 50 31 P12, TM2IO
A10, P72, SEG13 51 30 P10, RMOUT
A11, P73, SEG12 52 29 P27, NRST
A12, P74, SEG11 53 28 P06, BUZZER, /DK
A13, P75, SEG10 54 27 P02, SBT0
A14, P76, SEG9 55 26 P01, SBI0, RXD
A15, P77, SEG8 56 25 P00, SBO0, TXD
D7, P87, SEG7 57 24 VREF+
D6, P86, SEG6 58 23 PA7, AN7, KEY7
D5, P85, SEG5 59 22 PA6, AN6, KEY6
D4, P84, SEG4 60 21 PA5, AN5, KEY5
D3, P83, SEG3 61 20 PA4, AN4, KEY4
D2, P82, SEG2 62 19 PA3, AN3, KEY3
D1, P81, SEG1 63 18 PA2, AN2, KEY2
D0, P80, SEG0 64 17 PA1, AN1, KEY1
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9
COM3
COM2
COM1
COM0
VLC3
VLC2
VLC1
VDD
OSC2
OSC1
VSS
XI
XO
MMOD
VREF-
KEY0, AN0, PA0

MAD00012HEM 91
 MN101C54 Series
Type MN101C54A MN101C54C MN101CF54D MN101CP54C
Internal ROM type Mask ROM FLASH EPROM
ROM (byte) 32K 48K 64K 48K
RAM (byte) 2K
LQFP080-P-1414A,
Package (Lead-free) LQFP080-P-1414A, QFP084-P-1818E QFP084-P-1818E QFP084-P-1818E
0.1 µs (at 4.5 V to 5.5 V, 20 MHz)
0.25 µs (at 2.7 V to 5.5 V, 8 MHz)*1
Minimum Instruction 62.5 µs (at 2.0 V to 5.5 V, 32 kHz)*1,*2
Execution Time *1: The lower limit for operation guarantee for flash memory built-in type is 4.5 V.
*2: The lower limit for operation guarantee for EPROM built-in type is 2.3 V.

 Interrupts
RESET. Watchdog. External 0 to 2. External 3 (LQFP080-P-1414A: Not mounted). External 4 (key interrupt dedicated). Timer 0 to 3.
Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Time base. Serial 0 (2 systems). Serial 2. A/D conversion finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Square-wave/PWM output to large current terminal P50 possible
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. Event count. Synchronous output event. Simple pulse
width measurement. Square-wave/PWM output to large current terminal P52 possible
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count.
Synchronous output event. Pulse width measurement. Input capture. Square-wave/PWM output to large current
terminal P51 possible
Timer 8 ..................Square-wave/16-bit PWM output (duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P53 possible
Timer 7, 8 can be cascade-connected: Square-wave output, PWM, input capture, pulse width measurement is possible as a 32-bit
timer
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0
Synchronous type × 1: Serial 2

 I/O Pins
I/O 61 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
(60) : LQFP080-P-1414A
Input 4: Common use. Specified pull-up resistor available
(3) : LQFP080-P-1414A

 A/D converter
10-bit × 8 channels (with S/H)

 Display control function

LCD: 32 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
LCD power supply separated from VDD (usable if VDD ≤ VLCD ≤ 5.5 V)
LCD power step-up circuit contained (3/2 times, 2 times and 3 times)
LCD power shunt resistance contained

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

92 MAD00016LEM
 MN101C54A, MN101C54C, MN101CF54D, MN101CP54C

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 25 60 mA
Operating supply current IDD2 fosc = 8 MHz. VDD = 5 V 10 25 mA
IDD3 fx = 32 kHz. VDD = 3 V 30 100 µA
IDD4 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 4 8 µA
Supply current at HALT
IDD5 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 30 µA
IDD6 VDD = 5 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD7 VDD = 5 V. Ta = -40 °C to +85 °C 50 µA

 Pin Assignment
LQFP080-P-1414A

P47, KEY7, SEG24, SDO7

P46, KEY6, SEG25, SDO6
P45, KEY5, SEG26, SDO5
P44, KEY4, SEG27, SDO4
P43, KEY3, SEG28, SDO3
P42, KEY2, SEG29, SDO2
P41, KEY1, SEG30, SDO1
P40, KEY0, SEG31, SDO0

P21, IRQ1, ACZ

P67, SEG16
P66, SEG17
P65, SEG18
P64, SEG19
P63, SEG20
P62, SEG21
P61, SEG22
P60, SEG23

P22, IRQ2

P20, IRQ0
VDD
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
P70, SEG15 61 40 TM8IO, P15
P71, SEG14 62 39 TM7IO, P14
P72, SEG13 63 38 TM3IO, P13
P73, SEG12 64 37 TM2IO, P12
P74, SEG11 65 36 TM1IO, P11
P75, SEG10 66 35 RMOUT, TM0IO, P10
P76, SEG9 67 34 BUZZER, P06
P77, SEG8 68 33 SBT2, P05
P80, SEG7 69 32 SBI2, P04
P81, SEG6 70 31 SBO2, P03
P82, SEG5 71 30 SBT0, P02
P83, SEG4 72 29 RXD, SBI0, P01
P84, SEG3 73 28 TXD, SBO0, P00
P85, SEG2 74 27 VDD
P86, SEG1 75 26 VREF-
P87, SEG0 76 25 AN7, PA7
COM0, P30 77 24 AN6, PA6
COM1, P31 78 23 AN5, PA5
COM2, P32 79 22 AN4, PA4
COM3, P33 80 21 AN3, PA3
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9
VLC1
VLC2
VLC3
C1
C2
TM7O, LED1, P51
TM2O, LED2, P52
TM8O, LED3, P53
VSS
OSC2
OSC1
MMOD
XI
XO
VDD

VREF+
NRST, P27

AN0, PA0
AN1, PA1
AN2, PA2

MAD00016LEM 93
94
QFP084-P-1818E

P74, SEG11

COM3, P33
COM2, P32
COM1, P31
COM0, P30
N.C.
P87, SEG0
P86, SEG1
P85, SEG2
P84, SEG3
P83, SEG4
P82, SEG5
P81, SEG6
P80, SEG7
P77, SEG8
P76, SEG9
P75, SEG10
P73, SEG12
P72, SEG13
P71, SEG14
P70, SEG15

84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
VLC1 1 64 63 P67, SEG16
VLC2 2 62 P66, SEG17
VLC3 3 61 P65, SEG18
N.C. 4 60 P64, SEG19
N.C. 5 59 P63, SEG20
TM0O, LED0, P50 6 58 P62, SEG21
TM7O, LED1, P51 7 57 P61, SEG22
TM2O, LED2, P52 8 56 P60, SEG23
TM8O, LED3, P53 9 55 P47, KEY7, SEG24, SDO7
NATRST 10 54 P46, KEY6, SEG25, SDO6
VSS 11 53 P45, KEY5, SEG26, SDO5
OSC2 12 52 P44, KEY4, SEG27, SDO4
OSC1 13 51 P43, KEY3, SEG28, SDO3
MMOD 14 50 P42, KEY2, SEG29, SDO2
XI 15 49 P41, KEY1, SEG30, SDO1
XO 16 48 P40, KEY0, SEG31, SDO0
VDD 17 47 VDD
NRST, P27 18 46 P23, IRQ3
VREF+ 19 45 P22, IRQ2
AN0, PA0 20 44 P21, IRQ1, ACZ
AN1, PA1 21 22 43 P20, IRQ0
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42

VDD
VREF-
SBI2, P04

AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6
AN7, PA7
SBT0, P02
SBT2, P05

SBO2, P03
TM1IO, P11
TM2IO, P12
TM3IO, P13
TM7IO, P14
TM8IO, P15

BUZZER, P06

RXD, SBI0, P01

TXD, SBO0, P00
RMOUT, TM0IO, P10

MAD00016LEM
95
 MN101C57 Series
Type MN101C57C MN101C57D MN101CF57D
Internal ROM type Mask ROM FLASH
ROM (byte) 48K 64K
RAM (byte) 2K
Package (Lead-free) QFP100-P-1818B
0.1 µs (at 4.5 V to 5.5 V, 20 MHz)
Minimum Instruction 0.25 µs (at 2.7 V to 5.5 V, 8 MHz)
Execution Time 62.5 µs (at 2.0 V to 5.5 V, 32 kHz)*
*: The lower limit for operation guarantee for flash memory built-in type is 2.5 V.

 Interrupts
RESET. Watchdog. External 0 to 3. External 4 (key interrupt selectable). External 5 (key interrupt dedicated). External 6. External
7. Remote control. Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Time base. Serial 0 (2 systems). Serial 2. A/D
conversion finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Square-wave/PWM output to large current terminal P50 possible
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. Event count. Synchronous output event. Simple pulse
width measurement. Square-wave/PWM output to large current terminal P52 possible
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count.
Synchronous output event. Pulse width measurement. Input capture. Square-wave/PWM output to large current
terminal P51 possible
Timer 8 ..................Square-wave/16-bit PWM output (duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P53 possible
Timer 7, 8 can be cascade-connected: Square-wave output, PWM, input capture, pulse width measurement is possible as a 32-bit
timer
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0
Synchronous type × 1: Serial 2

 Remote Contorol Interface

Remote control output: Based on the timer 0 and timer 3 outpout, a remote control carrier with duty cycle of 1/2 or 1/3 can be output
Remote control reception: Queued reception by low speed clock. Compatible with the Kaseikyo format ( Setup can be adjusted to
optional format )

 I/O Pins
I/O 77 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
Input 6 : Common use. Specified pull-up resistor available

 A/D converter
10-bit × 16 channels (with S/H)

 Display control function

LCD: 47 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
LCD power supply separated from VDD (usable if VLCD ≤ VDD)
LCD power shunt resistance contained

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

96 MAD00019LEM
 MN101C57C, MN101C57D, MN101CF57D

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 15 30 mA
Operating supply current IDD2 fosc = 8 MHz. VDD = 5 V 8 16 mA
IDD3 fx = 32 kHz. VDD = 3 V 30 60(70) µA
IDD4 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 4 8 µA
Supply current at HALT
IDD5 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 30 µA
IDD6 VDD = 5 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD7 VDD = 5 V. Ta = -40 °C to +85 °C 50 µA
Note) ( ): Flash memory built-in type

 Pin Assignment
QFP100-P-1818B

PB5, SEG41, AN13, SBO0B, TXDB

PB6, SEG40, AN14, SBI0B, RXDB
PB7, SEG39, AN15, SBT0B
P47, SEG26, KEY7, SDO7
P46, SEG27, KEY6, SDO6
P45, SEG28, KEY5, SDO5
P44, SEG29, KEY4, SDO4
P43, SEG30, KEY3, SDO3
P42, SEG31, KEY2, SDO2
P41, SEG32, KEY1, SDO1
P40, SEG33, KEY0, SDO0

PB4, SEG42, AN12

PB2, SEG44, AN10

PB3, SEG43, AN11
P31, SEG37, IRQ7
P30, SEG38, IRQ6

PB1, SEG45, AN9

P64, SEG21, A4
P63, SEG22, A3
P62, SEG23, A2
P61, SEG24, A1
P60, SEG25, A0

P34, SEG34
P33, SEG35
P32, SEG36
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
P65, SEG20, A5 76 50 PB0, SEG46, AN8
P66, SEG19, A6 77 49 VREF-
P67, SEG18, A7 78 48 PA7, AN7
P70, SEG17, A8 79 47 PA6, AN6
P71, SEG16, A9 80 46 PA5, AN5
P72, SEG15, A10 81 45 PA4, AN4
P73, SEG14, A11 82 44 PA3, AN3
P74, SEG13, A12 83 43 PA2, AN2
P75, SEG12, A13 84 42 PA1, AN1
P76, SEG11, A14 85 41 PA0, AN0
P77, SEG10, A15 86 40 VREF+
P35, SEG9, A16 87 39 VDD
P36, SEG8, A17 88 38 P25, RMIRQ
P87, SEG7, D7 89 37 P24, IRQ4
P86, SEG6, D6 90 36 P23, IRQ3
P85, SEG5, D5 91 35 P22, IRQ2
P84, SEG4, D4 92 34 P21, IRQ1, ACZ
P83, SEG3, D3 93 33 P20, IRQ0
P82, SEG2, D2 94 32 P15, TM8IO
P81, SEG1, D1 95 31 P14, TM7IO
P80, SEG0, D0 96 30 P13, TM3IO
P90, COM0 97 29 P12, TM2IO
P91, COM1 98 28 P11, TM1IO
P92, COM2 99 27 P10, RMOUT, TM0IO
P93, COM3 100 26 P06, NDK, BUZZER
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
VLC1
VLCIN2, VLC2
VLCIN3, VLC3
N.C.
N.C.
NWE, TM0O, LED0, P50
NRE, TM7O, LED1, P51
NCS, TM2O, LED2, P52
TM8O, LED3, P53
LED4, P54
VSS
OSC1
OSC2
MMOD
XI
XO
VDD

VDD
KEY10, TXDA, SBO0A, PO0

KEY12, SBT0A, PO2

KEY13, SBO2, PO3
KEY14, SBI2, PO4
KEY15, SBT2, PO5
KEY11, RXDA, SBI0A, PO1
NRST, P27

MAD00019LEM 97
 MN101C58 Series
Type MN101C589 MN101C58A MN101CF58D MN101CP58A
Internal ROM type Mask ROM FLASH EPROM
ROM (byte) 24K 32K 64K 32K
RAM (byte) 1.5K 2K 1.5K
Package (Lead-free) LQFP064-P-1414
0.1 µs (at 4.5 V to 5.5 V, 20 MHz)
0.25 µs (at 2.7 V to 5.5 V, 8 MHz)*1
Minimum Instruction 62.5 µs (at 2.0 V to 5.5 V, 32 kHz)*1,*2
Execution Time *1: The lower limit for operation guarantee for flash memory built-in type is 4.5 V.
*2: The lower limit for operation guarantee for EPROM built-in type is 2.3 V.

 Interrupts
RESET. Watchdog. External 0 to 2. External 4 (key interrupt dedicated). Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems).
Time base. Serial 0 (2 systems). A/D conversion finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Square-wave/PWM output to large current terminal P50 possible
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. Event count. Synchronous output event. Simple pulse
width measurement. Square-wave/PWM output to large current terminal P52 possible
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count.
Synchronous output event. Pulse width measurement. Input capture. Square-wave/PWM output to large current
terminal P51 possible
Timer 8 ..................Square-wave/16-bit PWM output (duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P53 possible
Timer 7, 8 can be cascade-connected: Square-wave output, PWM, input capture, pulse width measurement is possible as a 32-bit
timer
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0

 I/O Pins
I/O 46 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
Input 3 : Common use. Specified pull-up resistor available

 A/D converter
10-bit × 8 channels (with S/H)

 Display control function

LCD: 24 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
LCD power supply separated from VDD (usable if VDD ≤ VLCD ≤ 5.5 V)
LCD power step-up circuit contained (3/2 times, 2 times and 3 times)
LCD power shunt resistance contained

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

98 MAD00014JEM
 MN101C589, MN101C58A, MN101CP58A, MN101CF58D

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 25 60 mA
Operating supply current IDD2 fosc = 8 MHz. VDD = 5 V 10 25 mA
IDD3 fx = 32 kHz. VDD = 3 V 30 100 µA
IDD4 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 4 8 µA
Supply current at HALT
IDD5 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 30 µA
IDD6 VDD = 5 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD7 VDD = 5 V. Ta = -40 °C to +85 °C 50 µA

 Pin Assignment
LQFP064-P-1414

SEG23, KEY0, P60, SDO0, SBO0B, TXDB

SEG22, KEY1, P61, SDO1, SBI0B, RXDB
SEG21, KEY2, P62, SDO2, SBT0B
SEG16, KEY7, P67, SDO7
SEG17, KEY6, P66, SDO6
SEG18, KEY5, P65, SDO5
SEG19, KEY4, P64, SDO4
SEG20, KEY3, P63, SDO3

P21, IRQ1, ACZ1

P20, IRQ0, ACZ0
P15, TM8IO
SEG12, P73
SEG13, P72
SEG14, P71
SEG15, P70

P22, IRQ2
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33

SEG11, P74 49 32 TM7IO, P14

SEG10, P75 50 31 TM3IO, P13
SEG9, P76 51 30 TM2IO, P12
SEG8, P77 52 29 TM1IO, P11
SEG7, P80 53 28 RMOUT, TM0IO, P10
SEG6, P81 54 27 AN7, BUZZER, P06
SEG5, P82 55 26 AN6, SBT0A, P02
SEG4, P83 56 25 AN5, RXDA, SBI0A, P01
SEG3, P84 57 24 AN4, TXDA, SBO0A, P00
SEG2, P85 58 23 VDD
SEG1, P86 59 22 AN3, PA3
SEG0, P87 60 21 AN2, PA2
COM0, P30 61 20 AN1, PA1
COM1, P31 62 19 AN0, PA0
COM2, P32 63 18 VREF+
COM3, P33 64 17 NRST, P27
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9
VLC1
VLCIN2, VLC2
VLCIN3, VLC3
C1
C2
TM0O, LED0, P50
TM7O, LED1, P51
TM2O, LED2, P52
TM8O, LED3, P53
VSS
OSC2
, OSC1

XI
XO
VDD
ATRST

MAD00014JEM 99
 MN101C66 Series
Type MN101C66D MN101C66G MN101CF66G MN101CP66D
Internal ROM type Mask ROM FLASH EPROM
ROM (byte) 64K 128K 64K
RAM (byte) 2K 4K 2K
LQFP080-P-1414A
LQFP080-P-1414A, (ES (Engineering
Package (Lead-free) LQFP080-P-1414A, QFP084-P-1818E
QFP084-P-1818E Sample) available),
QFP084-P-1818E
0.1 µs (at 4.5 V to 5.5 V, 20 MHz)
0.25 µs (at 2.7 V to 5.5 V, 8 MHz)
Minimum Instruction 62.5 µs (at 2.0 V to 5.5 V, 32 kHz)*
Execution Time *: The lower limit for operation guarantee for flash memory built-in type is 2.5 V.
The lower limit for operation guarantee for EPROM built-in type is 2.3 V.

 Interrupts
RESET. Watchdog. External 0 to 2. External 3 (LQFP080-P-1414A: Not mounted). External 4 (key interrupt dedicated). Timer 0 to 3.
Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Time base. Serial 0 (2 systems). Serial 2. A/D conversion finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Square-wave/PWM output to large current terminal P50 possible
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. Event count. Synchronous output event. Simple pulse
width measurement. Square-wave/PWM output to large current terminal P52 possible
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count.
Synchronous output event. Pulse width measurement. Input capture. Square-wave/PWM output to large current
terminal P51 possible
Timer 8 ..................Square-wave/16-bit PWM output (duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P53 possible
Timer 7, 8 can be cascade-connected: Square-wave output, PWM, input capture, pulse width measurement is possible as a 32-bit
timer
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0
Synchronous type × 1: Serial 2

 I/O Pins
I/O 61 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
(60) : LQFP080-P-1414A
Input 4: Common use. Specified pull-up resistor available
(3) : LQFP080-P-1414A

 A/D converter
10-bit × 8 channels (with S/H)

 Display control function

LCD: 32 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
LCD power supply separated from VDD (usable if VLCD ≤ VDD)
LCD power shunt resistance contained

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

100 MAD00017LEM
 MN101C66D, MN101C66G, MN101CF66G, MN101CP66D

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 25 60 mA
Operating supply current IDD2 fosc = 8 MHz. VDD = 5 V 10 25 mA
IDD3 fx = 32 kHz. VDD = 3 V 30 100 µA
IDD4 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 4 8 µA
Supply current at HALT
IDD5 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 30 µA
IDD6 VDD = 5 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD7 VDD = 5 V. Ta = -40 °C to +85 °C 50 µA

 Pin Assignment
LQFP080-P-1414A

P47, KEY7, SEG24, SDO7

P46, KEY6, SEG25, SDO6
P45, KEY5, SEG26, SDO5
P44, KEY4, SEG27, SDO4
P43, KEY3, SEG28, SDO3
P42, KEY2, SEG29, SDO2
P41, KEY1, SEG30, SDO1
P40, KEY0, SEG31, SDO0

P21, IRQ1, ACZ

P67, SEG16
P66, SEG17
P65, SEG18
P64, SEG19
P63, SEG20
P62, SEG21
P61, SEG22
P60, SEG23

P22, IRQ2

P20, IRQ0
VDD
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
P70, SEG15 61 40 TM8IO, P15
P71, SEG14 62 39 TM7IO, P14
P72, SEG13 63 38 TM3IO, P13
P73, SEG12 64 37 TM2IO, P12
P74, SEG11 65 36 TM1IO, P11
P75, SEG10 66 35 RMOUT, TM0IO, P10
P76, SEG9 67 34 BUZZER, P06
P77, SEG8 68 33 SBT2, P05
P80, SEG7 69 32 SBI2, P04
P81, SEG6 70 31 SBO2, P03
P82, SEG5 71 30 SBT0, P02
P83, SEG4 72 29 RXD, SBI0, P01
P84, SEG3 73 28 TXD, SBO0, P00
P85, SEG2 74 27 VDD
P86, SEG1 75 26 VREF-
P87, SEG0 76 25 AN7, PA7
COM0, P30 77 24 AN6, PA6
COM1, P31 78 23 AN5, PA5
COM2, P32 79 22 AN4, PA4
COM3, P33 80 21 AN3, PA3
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9
VLC1
VLC2
VLC3
N.C
N.C
TM7O, LED1, P51
TM2O, LED2, P52
TM8O, LED3, P53
VSS
OSC2
OSC1
MMOD
XI
XO
VDD

VREF+
NRST, P27

AN0, PA0
AN1, PA1
AN2, PA2

MAD00017LEM 101
102
QFP084-P-1818E

P74, SEG11

COM3, P33
COM2, P32
COM1, P31
COM0, P30
N.C.
P87, SEG0
P86, SEG1
P85, SEG2
P84, SEG3
P83, SEG4
P82, SEG5
P81, SEG6
P80, SEG7
P77, SEG8
P76, SEG9
P75, SEG10
P73, SEG12
P72, SEG13
P71, SEG14
P70, SEG15

84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
VLC1 1 64 63 P67, SEG16
VLC2 2 62 P66, SEG17
VLC3 3 61 P65, SEG18
N.C. 4 60 P64, SEG19
N.C. 5 59 P63, SEG20
TM0O, LED0, P50 6 58 P62, SEG21
TM7O, LED1, P51 7 57 P61, SEG22
TM2O, LED2, P52 8 56 P60, SEG23
TM8O, LED3, P53 9 55 P47, KEY7, SEG24, SDO7
NATRST 10 54 P46, KEY6, SEG25, SDO6
VSS 11 53 P45, KEY5, SEG26, SDO5
OSC2 12 52 P44, KEY4, SEG27, SDO4
OSC1 13 51 P43, KEY3, SEG28, SDO3
MMOD 14 50 P42, KEY2, SEG29, SDO2
XI 15 49 P41, KEY1, SEG30, SDO1
XO 16 48 P40, KEY0, SEG31, SDO0
VDD 17 47 VDD
NRST, P27 18 46 P23, IRQ3
VREF+ 19 45 P22, IRQ2
AN0, PA0 20 44 P21, IRQ1, ACZ
AN1, PA1 21 22 43 P20, IRQ0
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42

VDD
VREF-
SBI2, P04

AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6
AN7, PA7
SBT0, P02
SBT2, P05

SBO2, P03
TM1IO, P11
TM2IO, P12
TM3IO, P13
TM7IO, P14
TM8IO, P15

BUZZER, P06

RXD, SBI0, P01

TXD, SBO0, P00
RMOUT, TM0IO, P10

MAD00017LEM
103
 MN101C70 Series
Type MN101C70C MN101CF70D
Internal ROM type Mask ROM FLASH
ROM (byte) 48K 64K
RAM (byte) 2K 4K
Package (Lead-free) LQFP080-P-1414A LQFP080-P-1414A (Under development)
0.1 µs (at 3.0 V to 3.6 V, 10 MHz) 0.25 µs (at 3.0 V to 3.6 V, 8 MHz)
Minimum Instruction 0.235 µs (at 1.8 V to 3.6 V, 4.25 MHz) 0.50 µs (at 2.2 V to 3.6 V, 4 MHz)
Execution Time 62.5 µs (at 1.8 V to 3.6 V, 32 kHz) 62.5 µs (at 2.2 V to 3.6 V, 32 kHz)

 Interrupts
RESET. Watchdog. External 0 to 2. External 4 (key interrupt dedicated). Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems).
Time base. Serial 0 (2 systems). Serial 2. A/D conversion finish. Automatic transfer finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Added pulse (2-bit) type PWM output. Real time output control. Square-wave/PWM output to large current
terminal P50 possible
Timer 1 ..................Square-wave output. Event count. Synchronous output event. Serial transfer clock output
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. PWM output. Serial transfer clock output. Real time
output control. Event count. Synchronous output event. Simple pulse width measurement. Square-wave/PWM
output to large current terminal P52 possible
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial transfer clock output
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output
event. Pulse width measurement. Input capture. Real time output control. High performance IGBT output. Square-
wave/PWM output to large current terminal P51 possible
Timer 8 ..................Square-wave/16-bit PWM output (duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P53 possible
Timer 7, 8 can be cascade-connected: Square-wave output, PWM is possible as a 32-bit timer
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0
Synchronous type/Single-master I2C × 1: Serial 2

 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 66 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 16 channels (with S/H)

 Display control function

LCD: 32 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
LCD power supply separated from VDD (usable if VDD ≤ VLCD ≤ 3.6 V)
LCD power step-up circuit contained (3/2 times, 2 times and 3 times)
LCD power shunt resistance contained

 Special Ports
Buzzer output. Inverted buzzer output. Remote control carrier output. High-current drive port

104 MAD00035NEM
 MN101C70C, MN101CF70D

 ROM Correction
Correcting address designation: Up to 3 addresses possible

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 4 MHz. VDD = 3 V 1 1.8 mA
Operating supply current
IDD2 fx = 32 kHz. VDD = 3 V 4 15 µA
IDD3 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 2 5 µA
Supply current at HALT
IDD4 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 10 µA
IDD5 VDD = 3 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD6 VDD = 3 V. Ta = -40 °C to +85 °C 8 µA

 Pin Assignment
LQFP080-P-1414A
P62, SEG21, SBO0B, TXDB
P63, SEG20, SBI0B, RXDB

P47, KEY7, SEG24, SDO7

P46, KEY6, SEG25, SDO6
P45, KEY5, SEG26, SDO5
P44, KEY4, SEG27, SDO4
P43, KEY3, SEG28, SDO3
P42, KEY2, SEG29, SDO2
P41, KEY1, SEG30, SDO1
P40, KEY0, SEG31, SDO0
P61, SEG22, NBUZZERB
P60, SEG23, BUZZERB
P64, SEG19, SBT0B

P21, IRQ1, ACZ

P67, SEG16
P66, SEG17
P65, SEG18

P22, IRQ2

P20, IRQ0
VDD
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41

P70, SEG15 61 40 TM8IO, P15

P71, SEG14 62 39 TM7IO, P14
P72, SEG13 63 38 TM3IO, P13
P73, SEG12 64 37 TM2IO, P12
P74, SEG11 65 36 TM1IO, P11
P75, SEG10 66 35 RMOUT, TM0IO, P10
P76, SEG9 67 34 SBT2, P07
P77, SEG8 68 33 SBI2, P06
P80, SEG7 69 32 SBO2, P05
P81, SEG6 70 31 SBT0A, P04
P82, SEG5 71 30 RXDA, SBI0A, P03
P83, SEG4 72 29 TXDA, SBO0A, P02
P84, SEG3 73 28 NBUZZERA, AN9, P01
P85, SEG2 74 27 BUZZERA, AN8, P00
P86, SEG1 75 26 AN7, PA7
P87, SEG0 76 25 AN6, PA6
P30, COM0 77 24 AN5, PA5
P31, COM1 78 23 AN4, PA4
P32, COM2 79 22 AN3, PA3
P33, COM3 80 21 AN2, PA2
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9
VLC3, P34
VLC2
VLC1
C2
TM0O, LED0, P50, C1
TM7O, LED1, P51
TM2O, LED2, P52
TM8O, LED3, P53
VSS
OSC2
OSC1

XI
XO
SOSCMD
VDD

VREF+
SSTRT

NRST, P27

AN0, PA0
AN1, PA1

MAD00035NEM 105
 MN101C73 Series
Type MN101C73A MN101CF73A
Internal ROM type Mask ROM FLASH
ROM (byte) 32K
RAM (byte) 1.5K 2K
Package (Lead-free) LQFP064-P-1414, TQFP064-P-1010C
0.1 µs (at 3.0 V to 3.6 V, 10 MHz)
Minimum Instruction 0.235 µs (at 1.8 V to 3.6 V, 4.25 MHz)*
Execution Time 62.5 µs (at 1.8 V to 3.6 V, 32 kHz)*
*: The lower limit for operation guarantee for flash memory built-in type is 2.2 V.

 Interrupts
RESET. Watchdog. External 0 to 5. External 6 (key interrupt dedicated). Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems).
Time base. Serial 0 (2 systems). Serial 1 (2 systems). Serial 3. A/D conversion finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Added pulse (2-bit) type PWM output. Square-wave/PWM output to large current terminal P50 possible
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. PWM output. Serial transfer clock output. Event
count. Synchronous output event. Simple pulse width measurement. Square-wave/PWM output to large current
terminal P51 possible
Timer 3 ..................Square-wave output. Event count. Serial transfer clock output
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output
event. Pulse width measurement. Input capture. Real time output control. High performance IGBT output. Square-
wave/PWM output to large current terminal P52 possible
Timer 8 ..................Square-wave/16-bit PWM output (duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P53 possible
Timer 7, 8 can be cascade-connected: Square-wave output, PWM is possible as a 32-bit timer
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Single-master I2C × 1: Serial 3

 I/O Pins
I/O 55 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 12 channels (with S/H)

 Display control function

LCD: 32 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
Usable if VLCD ≤ VDD
LCD power shunt resistance contained

 Special Ports
Buzzer output. Inverted buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 3 addresses possible

106 MAD00047GEM
 MN101C73A, MN101CF73A

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 4 MHz. VDD = 3 V 1 1.8 mA
Operating supply current
IDD2 fx = 32 kHz. VDD = 3 V 4 15 µA
IDD3 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 2 5 µA
Supply current at HALT
IDD4 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 10 µA
IDD5 VDD = 3 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD6 VDD = 3 V. Ta = -40 °C to +85 °C 8 µA

 Pin Assignment
TQFP064-P-1010C, LQFP064-P-1414

SEG15, P60, SBO0B, TXD0B

SEG18, P05, SBO1B, TXD1B

SEG14, P61, SBI0B, RXD0B

SEG17, P06, SBI1B, RXD1B

SEG10, P71, KEY1B
SEG11, P70, KEY0B

SEG13, P62, SBT0B

SEG16, P07, SBT1B

SEG4, P77, KEY7B
SEG5, P76, KEY6B
SEG6, P75, KEY5B
SEG7, P74, KEY4B
SEG8, P73, KEY3B
SEG9, P72, KEY2B

SEG19, P04, SBT3

SEG12, P63
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
SEG3, P64 49 33 32 SEG20, SBO3, P03
SEG2, P65 50 31 SEG21, SBI3, IRQ5, P02
SEG1, P66 51 30 SEG22, NBUZZER, IRQ4, P01
SEG0, P67 52 29 SEG23, BUZZERA, IRQ3, P00
COM0, P30 53 28 IRQ2, SBT1A, P23
COM1, P31 54 27 IRQ1, SBI1A, RXD1A, P22
COM2, P32 55 26 IRQ0, SBO1A, TXD1A, P21
COM3, P33 56 25 VREF+, P20
SEG24, P8O, SDO0, TM7IOB 57 24 AN0, KEY7A, TM3IOA, P17
SEG25, P81, SDO1, TM8IOB 58 23 , AN1, KEY6A, TM2IOA, P16
SEG26, P82, SDO2, TM0IOB 59 22 AN2, KEY5A, TM1IOA, P15
SEG27, P83, SDO3, TM1IOB 60 21 AN3, KEY4A, SBT0A, TM0IOA, P14
SEG28, P84, SDO4, TM2IOB 61 20 AN4, KEY3A, SBI0A, RXD0A, P13
SEG29, P85, SDO5, TM3IOB 62 19 AN5, KEY2A, SBO0A, TXD0A, P12
SEG30, P86, SDO6 63 18 AN6, KEY1A, TM8IOA, P11
SEG31, P87, SDO7 64 17 AN7, KEY0A, TM7IOA, P10
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9
P34, VLC3
P35, VLC2
P36, VLC1
VDD
VDD (Flash, VPP)
OSC2
OSC1
MMOD
XO
XI

VSS

AN10, TM2O, LED1, P51

AN9, BUZZERB, TM7O, LED2, P52
AN8, TM8O, LED3, P53
NRST, P27

AN11, RMOUT, TM0O, LED0, P50

MAD00047GEM 107
 MN101C74 Series
Type MN101C74F MN101C74G MN101CF74G
Internal ROM type Mask ROM FLASH
ROM (byte) 96K 128K
RAM (byte) 6K
Package (Lead-free) LQFP100-P-1414, MLGA100-L-1010, QFP100-P-1818B
0.1 µs (at 3.0 V to 3.6 V, 10 MHz)
Minimum Instruction 0.235 µs (at 1.8 V to 3.6 V, 4.25 MHz)*
Execution Time 62.5 µs (at 1.8 V to 3.6 V, 32 kHz)*
*: The lower limit for operation guarantee for flash memory built-in type is 2.2 V.

 Interrupts
RESET. Watchdog. External 0 to 5. External 6 (key interrupt dedicated). Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems).
Time base. Serial 0 (2 systems). Serial 1 (2 systems). Serial 3. Serial 4. A/D conversion finish. Automatic transfer finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Added pulse (2-bit) type PWM output. Square-wave/PWM output to large current terminal PC3 possible
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. PWM output. Serial transfer clock output. Event
count. Synchronous output event. Simple pulse width measurement. Square-wave/PWM output to large current
terminal PC5 possible
Timer 3 ..................Square-wave output. Event count. Serial transfer clock output
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output
event. Pulse width measurement. Input capture. Real time output control. High performance IGBT output. Square-
wave/PWM output to large current terminal PC4 possible
Timer 8 ..................Square-wave/16-bit PWM output (duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal PC6 possible
Timer 7, 8 can be cascade-connected: Square-wave output, PWM is possible as a 32-bit timer
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Single-master I2C × 1: Serial 3
I2C slave × 1: Serial 4
Serial 4...................I2C high-speed transfer mode. 7-bit/10-bit address setting. General call

 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 87 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 16 channels (with S/H)

 Display control function

LCD: 47 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
LCD power supply separated from VDD (usable if VDD ≤ VLCD ≤ 3.6 V)
LCD power step-up circuit contained (3/2 times, 2 times and 3 times)
LCD power shunt resistance contained

 Special Ports
Buzzer output. Inverted buzzer output. Remote control carrier output. High-current drive port
108 MAD00048GEM
 MN101C74F, MN101C74G, MN101CF74G

 ROM Correction
Correcting address designation: Up to 7 addresses possible

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 4 MHz. VDD = 3 V 1.1 1.9 mA
Operating supply current
IDD2 fx = 32 kHz. VDD = 3 V 6 20 µA
IDD3 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 3 6 µA
Supply current at HALT
IDD4 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 13 µA
IDD5 VDD = 3 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD6 VDD = 3 V. Ta = -40 °C to +85 °C 10 µA

 Pin Assignment
QFP100-P-1818B, LQFP100-P-1414, MLGA100-L-1010

P02, SEG44, SYSCLK, SBT3B, SCL3B

P03, SEG43, NDK, SBO3B, SDA3B

P01, SEG45, NBUZZER, SCL4B

P00, SEG46, BUZZER, SDA4B
P47, SEG32, D7, KEY7, SDO7
P46, SEG33, D6, KEY6, SDO6
P45, SEG34, D5, KEY5, SDO5
P44, SEG35, D4, KEY4, SDO4
P43, SEG36, D3, KEY3, SDO3
P42, SEG37, D2, KEY2, SDO2
P41, SEG38, D1, KEY1, SDO1
P40, SEG39, D0, KEY0, SDO0

P04, SEG42, NCS, SBI3B

P05, SEG41, NWE
P06, SEG40, NRE
P56, SEG25, A6
P55, SEG26, A5
P54, SEG27, A4
P53, SEG28, A3
P52, SEG29, A2
P51, SEG30, A1
P50, SEG31, A0

P25, IRQ5
P24, IRQ4
P23, IRQ3
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
A7, SEG24, P57 76 50 P22, IRQ2
A8, SEG23, P60 77 49 P21, ACZ1, IRQ1
A9, SEG22, P61 78 48 P20, IRQ0
A10, SEG21, P62 79 47 P15, TM8IO
A11, SEG20, P63 80 46 P14, TM7IO
A12, SEG19, P64 81 45 P13, TM3IO
A13, SEG18, P65 82 44 P12, TM2IO
A14, SEG17, P66 83 43 P11, TM1IO
A15, SEG16, P67 84 42 P10, TM0IO, RMOUT
A16, SEG15, P70 85 41 PB7, AN15, SBI1, RXD1
A17, SEG14, P71 86 40 PB6, AN14, SBO1, TXD1
SEG13, P72 87 39 PB5, AN13, SBT1
SEG12, P73 88 38 PB4, AN12, SBI0A, RXD0A
SEG11, P74 89 37 PB3, AN11, SBO0A, TXD0A
SEG10, P75 90 36 PB2, AN10, SBT0A
SEG9, P76 91 35 PB1, AN9, SCL4A
SEG8, P77 92 34 PB0, AN8, SDA4A
SEG7, P80 93 33 PA7, AN7, SBI3A
SEG6, P81 94 32 PA6, AN6, SBO3A, SDA3A
SEG5, P82 95 31 PA5, AN5, SBT3A, SCL3A
SEG4, P83 96 30 PA4, AN4
SEG3, P84 97 29 PA3, AN3
SEG2, P85 98 28 PA2, AN2
SEG1, P86 99 27 PA1, AN1
SEG0, P87 100 26 PA0, AN0
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
COM0, P90
COM1, P91
COM2, P92
COM3, P93
VLC3, P94
VLC2
VLC1
C2
C1, RXD0B, SBI0B, LED0, PC0
TXD0B, SBO0B, LED1, PC1
SBT0B, LED2, PC2
TM0O, LED3, PC3
TM7O, LED4, PC4
TM2O, LED5, PC5
TM8O, LED6, PC6
VSS
OSC1
OSC2
VDD
XI
XO
MMOD

DMOD
VREF+
NRST, P27

MAD00048GEM 109
 MN101C78 Series
Type MN101C78A MN101CF78A
Internal ROM type Mask ROM FLASH
ROM (byte) 32K
RAM (byte) 1.5K
Package (Lead-free) TQFP048-P-0707B
0.100 µs (at 3.0 V to 3.6 V, 10 MHz)
0.118 µs (at 2.7 V to 3.6 V, 8.5 MHz)
Minimum Instruction 0.235 µs (at 1.8 V to 3.6 V, 4.25 MHz)*
Execution Time 62.5 µs (at 1.8 V to 3.6 V, 32 kHz)*
*: The lower limit for operation guarantee for flash memory built-in type is 2.2 V.

 Interrupts
RESET. Watchdog. External 0 to 2. External 4 (key interrupt dedicated). Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems).
Time base. Serial 0 (2 systems). Serial 1 (2 systems). Serial 3. Serial 4. A/D conversion finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Added pulse (2-bit) type PWM output. Real time output control. Square-wave/PWM output to large current
terminal P50 possible
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. PWM output. Serial transfer clock output. Real time
output control. Event count. Synchronous output event. Simple pulse width measurement. Square-wave/PWM
output to large current terminal P52 possible
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output
event. Pulse width measurement. Input capture. Real time output control. High performance IGBT output. Square-
wave/PWM output to large current terminal P51 possible
Timer 8 ..................Square-wave/16-bit PWM output (duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P53 possible
Timer 7, 8 can be cascade-connected: Square-wave output, PWM, input capture, pulse width measurement is possible as a 32-bit
timer
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Single-master I2C × 1: Serial 3
I2C slave × 1: Serial 4
Serial 4...................I2C high-speed transfer mode. 7-bit/10-bit address setting. General call

 I/O Pins
I/O 39 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 7 channels (with S/H)

 Display control function

LCD: 12 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
Usable if VLCD ≤ VDD

 Special Ports
Buzzer output. Inverted buzzer output. Remote control carrier output. High-current drive port

110 MAD00039GEM
 MN101C78A, MN101CF78A

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 4.25 MHz (fs = fosc/2). VDD = 3 V 0.6(1.3) 1.1(2.2) mA
Operating supply current
IDD2 fx = 32 kHz (fs = fx/2). VDD = 3 V 4(46) 15(90) µA
IDD3 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 2(3) 5(13) µA
Supply current at HALT
IDD4 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 10(40) µA
IDD5 VDD = 3 V. Ta = 25 °C 2(3) µA
Supply current at STOP
IDD6 VDD = 3 V. Ta = -40 °C to +85 °C 8(30) µA
Note) ( ): Flash memory built-in type

 Pin Assignment
TQFP048-P-0707B

SEG10, P15, TM0OB, TXD1A, SBO1A

SEG9, P16, TM2IO, RXD1A, SBI1A

NBUZZER, P13, TM7IO, CLKOUT

SEG11, P14, TM0IO, RMOUT
SEG8, P17, SBT1A, TM2OB
SEG6, P71, KEY1, TM3IO
SEG7, P70, KEY0, TM1IO

BUZZER, P12, TM8IO

SEG4, P73, KEY3
SEG5, P72, KEY2

P55, IRQ1, ACZ1

P56, IRQ2
36
35
34
33
32
31
30
29
28
27
26
25

SEG3, P74, KEY4 37 24 P54, IRQ0, ACZ0

SEG2, P75, KEY5, TXD0B, SBO0B 38 23 VDD
SEG1, P76, KEY6, RXD0B, SBI0B, SDA4B 39 22 SBT1B, PA6, AN6
SEG0, P77, KEY7, SBT0B, SCL4B 40 21 TXD1B, SBO1B, PA5, AN5
COM0, P30 41 20 RXD1B, SBI1B, PA4, AN4
COM1, P31, SBI3 42 19 PA3, AN3
COM2, P32, SBT3, SCL3 43 18 SBT0A, PA2, AN2
COM3, P33, SB03, SDA3 44 17 RXD0A, SBI0A, PA1, AN1
P34, VLC3 45 16 TXD0A, SBO0A, PA0, AN0
P35, VLC2 46 15 VREF+
P36, VLC1 47 14 P11, SCL4A
P37 48 13 P10, SDA4A
10

12
11
1
2
3
4
5
6
7
8
9
TM0OA, LED0, P50
TM7O, LED1, P51
TM2OA, LED2, P52
TM8O, LED3, P53
VSS
OSC2
OSC1
VDD
XI, P90
XO
MMOD
NRST, P27

MAD00039GEM 111
 MN101C84 Series
Type MN101C84A MN101CF84D
Internal ROM type Mask ROM FLASH
ROM (byte) 32K 64K
RAM (byte) 1K 2K
Package (Lead-free) LQFP064-P-1414
0.1 µs (at 4.5 V to 5.5 V, 20 MHz)
Minimum Instruction 0.25 µs (at 2.7 V to 5.5 V, 8 MHz)
Execution Time 62.5 µs (at 2.0 V to 5.5 V, 32 kHz)*
*: The lower limit for operation guarantee for flash memory built-in type is 2.5 V.

 Interrupts
RESET. Watchdog. External 0 to 2. External 4 (key interrupt dedicated). Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems).
Time base. Serial 0 (2 systems). A/D conversion finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Square-wave/PWM output to large current terminal P50 possible
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. Event count. Synchronous output event. Simple pulse
width measurement. Square-wave/PWM output to large current terminal P52 possible
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count.
Synchronous output event. Pulse width measurement. Input capture. Square-wave/PWM output to large current
terminal P51 possible
Timer 8 ..................Square-wave/16-bit PWM output (duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P53 possible
Timer 7, 8 can be cascade-connected: Square-wave output, PWM, input capture, pulse width measurement is possible as a 32-bit
timer
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0

 I/O Pins
I/O 53 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
Input 3 : Common use. Specified pull-up resistor available

 A/D converter
10-bit × 8 channels (with S/H)

 Display control function

LCD: 32 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
LCD power supply separated from VDD (usable if VLCD ≤ VDD ≤ 5.5 V)
LCD power shunt resistance contained

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

112 MAD00049GEM
 MN101C84A, MN101CF84D

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 20 MHz. VDD = 5 V 15 30 mA
Operating supply current
IDD2 fosc = 8 MHz. VDD = 5 V 8 16 mA
Operating supply current IDD3 fx = 32 kHz. VDD = 3 V 30 60 µA
IDD4 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 4 8 µA
Supply current at HALT
IDD5 fx = 32 kHz. VDD = 3 V. Ta = -40 °C to +85 °C 30 µA
IDD6 VDD = 5 V. Ta = 25 °C 2 µA
Supply current at STOP
IDD7 VDD = 5 V. Ta = -40 °C to +85 °C 50 µA

 Pin Assignment
LQFP064-P-1414

P60, SEG23, KEY0, SBO0B, TXDB, SD00

P61, SEG22, KEY1, SBI0B, RXDB, SD01
P62, SEG21, KEY2, SBT0B, SD02

P21, SEG25, IRQ1A, ACZ1

P67, SEG16, KEY7, SD07
P66, SEG17, KEY6, SD06
P65, SEG18, KEY5, SD05
P64, SEG19, KEY4, SD04
P63, SEG20, KEY3, SD03

P15, SEG27, TM8IOA

P22, SEG24, IRQ2A

P20, SEG26, IRQ0A

P73, SEG12
P72, SEG13
P71, SEG14
P70, SEG15
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33

P74, SEG11 49 32 TM7IOA, SEG28, P14

P75, SEG10 50 31 TM3IO, SEG29, P13
P76, SEG9 51 30 TM2IOA, SEG30, P12
P77, SEG8 52 29 TM1IO, SEG31, P11
P80, SEG7 53 28 RMOUT, TM0IOA, P10
P81, SEG6 54 27 AN7, BUZZER, P06
P82, SEG5 55 26 AN6, SBT0A, P02
P83, SEG4 56 25 AN5, RXDA, SBI0A, P01
P84, SEG3 57 24 AN4, TXDA, SBO0A, P00
P85, SEG2 58 23 VDD
P86, SEG1 59 22 AN3, PA3
P87, SEG0 60 21 IRQ2B, AN2, PA2
P30, COM0 61 20 IRQ1B, AN1, PA1
P31, COM1 62 19 IRQ0B, AN0, PA0
P32, COM2 63 18 P96, VREF+
P33, COM3 64 17 NRST, P27
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9
VLC1, P90
VLC2, P91
VLC3, P92
P93
MMOD
RMOUTB, TM0IOB, LED0, P50
TM7IOB, LED1, P51
TM2IOB, LED2, P52
TM8IOB, LED3, P53
VSS
OSC2
OSC1

P94, XI
XO
VDD
ATRST

MAD00049GEM 113
 MN101CA2 Series
Type MN101CA27 MN101CFA2D
Internal ROM type Mask ROM FLASH
ROM (byte) 16K 64K
RAM (byte) 0.5K 2K
Package (Lead-free) LQFP064-P-1414
0.25 µs (at 2.7 V to 3.6 V, 8 MHz)
Minimum Instruction 0.50 µs (at 1.8 V to 3.6 V, 4 MHz)
Execution Time 62.5 µs (at 1.8 V to 3.6 V, 32 kHz)

 Interrupts
RESET. Watchdog. External 2. External 6. Timer 0. Timer 1. Timer 6. Time base

 Timer Counter
8-bit timer × 2
Timer 0 ..................Square-wave/8-bit PWM output. Simple pulse width measurement
Timer 1 ..................Square-wave output
Timer 0, 1 can be cascade-connected
Time base timer: One-minute count setting
Watchdog timer × 1
Remote control carrier output

 I/O Pins
I/O 16 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
Input 9 : Common use. Specified pull-up resistor available

 Display control function

LCD: 32 segments × 4 commons (1/3 or 1/4 duty)

 Special Ports
Buzzer output. Remote control carrier output. High-current drive port

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
IDD1 fosc = 8 MHz. VDD = 3 V 1.0 1.8 mA
Operating supply current
IDD2 fx = 32 kHz. VDD = 3 V 4.8 17 µA
IDD3 fx = 32 kHz. VDD = 3 V. Ta = 25 °C 2.7 5 µA
Supply current at HALT
IDD4 fx = 32 kHz. VDD = 3 V. Ta = 70 °C 13 µA
VDD = 3 V. Ta = 25 °C 2 µA
Supply current at STOP IDD5
VDD = 3 V. Ta = 70 °C 8 µA
Note) Limit: Mask ROM version

114 MAD00070DEM
 MN101CA27, MN101CFA2D

 Pin Assignment
LQFP064-P-1414

P21, RMOUT
P37, SEG24
P36, SEG25
P35, SEG26
P34, SEG27
P33, SEG28
P32, SEG29
P31, SEG30
P30, SEG31

P07, KEY7
P06, KEY6
P05, KEY5
P04, KEY4
P20, IRQ2
SEG22
SEG23
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
SEG21 49 32 P17
SEG20 50 31 P16
SEG19 51 30 P15
SEG18 52 29 P14
SEG17 53 28 P13
SEG16 54 27 TM1O, P12
SEG15 55 26 TM0O, P11
SEG14 56 25 BUZZER, P10
SEG13 57 24 KEY3, P03
SEG12 58 23 KEY2, P02
SEG11 59 22 KEY1, P01
SEG10 60 21 KEY0, P00
SEG9 61 20 NRST, P27
SEG8 62 19 VSS
SEG7 63 18 XI
SEG6 64 17 XO
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9
SEG5
SEG4
SEG3
SEG2
SEG1
SEG0
COM3
COM2
COM1
COM0
VLC3, MMOD
VLC2
VLC1
VDD
OSC1
OSC2

MAD00070DEM 115
 MN101E29 Series
Type MN101E29G MN101EF29G
Internal ROM type Mask ROM FLASH
ROM (byte) 128K 128K+4K
RAM (byte) 6K
Package (Lead-free) LQFP100-P-1414, QFP100-P-1818B
Minimum Instruction 50 ns (at 2.2 V to 5.5 V, 20 MHz)
Execution Time *: at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used

 Interrupts
6 external interrupts. 28 internal interrupts
RESET. NMI. External 0 to 4. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Timer 9 (2 systems). Time base. Serial
0 (2 systems). Serial 1 (2 systems). Serial 2 (2 systems). Serial 3 (2 systems). Serial 4. Serial 5. A/D conversion. Automatic transfer (2
systems). Key interrupt

 Timer Counter
8-bit timer × 7
Timer 0 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Remote control carrier output. Simple
pulse width measurement. Real time output control
Timer 1 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 0, 1). Timer synchronous output
Timer 2 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Simple pulse width measurement. 24-bit
cascade connected (timer 0, 1, 2). Timer synchronous output. Real time output control
Timer 3 ..................Timer pulse output. Event count. Remote control carrier output. 16-bit cascade connected (timer 2, 3). 32-bit
cascade connected (timer 0, 1, 2, 3)
Timer 4 ..................Timer pulse output. Added pulse (2-bit) type PWM output. Event count. Serial transfer clock output. Simple pulse
width measurement
Timer 6 ..................8-bit freerun timer. Time base timer
Timer A..................Event count. Baud rate timer. Clock output for peripheral function
16-bit timer × 3
Timer 7 ..................Timer pulse output. Event count. High accuracy PWM. High performance IGBT output (cycle/duty continuous
variable). Timer synchronous output. Input capture (both edge available). Real time output control. Double buffer
compare register
Timer 8 ..................Timer pulse output. Event count. High accuracy PWM output (cycle/duty continuous variable). Pulse width
measurement. Input capture (both edge available). 32-bit cascade connected (timer 7, 8). 32-bit PWM output.
Synchronous output event. Double buffer compare register
Timer 9 ..................Timer pulse output. Event count. High accuracy PWM output (cycle/duty continuous variable). Pulse width
measurement. Input capture (both edge available). Real time output control. Double buffer compare register
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 4: Serial 0 to 3
Synchronous type/Multi-master I2C × 1: Serial 4
I2C slave × 1: Serial 5

 DMA controller
2 systems. Maximum transfer cycles are 255
Starting factor: External request. Internal event. Software

 I/O Pins
I/O 90 : Common use. Specified pull-up/pull-down resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 16 channels

 D/A converter
8-bit × 4 channels

 Display control function

LCD: 55 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty) 1/3 bias
Usable if VLC1 ≤ VDD

116 MAD00062FEM
 MN101E29G, MN101EF29G

 Special Ports
Buzzer output. Inverted buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 7 addresses possible

 Pin Assignment
LQFP100-P-1414, QFP100-P-1818B

P50, SBO0A, TXD0A, KEY0, D0, SEG20

P51, SBI0A, RXD0A, KEY1, D1, SEG21

P54, NBUZZERA, KEY4, D4, SEG24

P53, BUZZERA, KEY3, D3, SEG23
P70, SBO2A, TXD2A, A6, SEG11

P66, SBO4A, SDA4A, A4, SEG13

P71, SBI2A, RXD2A, A7, SEG10

P67, SBT4A, SCL4A, A5, SEG12

P52, SBT0A, KEY2, D2, SEG22

P43, SBO0B, TXD0B, SEG32

P44, SBI0B, RXD0B, SEG31
P64, TM4IOB, A2, SEG15
P63, TM3IOB, A1, SEG16
P62, TM1IOB, A0, SEG17
P72, SBT2A, NWE, SEG9

P65, SBI4A, A3, SEG14

P55, KEY5, D5, SEG25

P56, KEY6, D6, SEG26
P57, KEY7, D7, SEG27

P46, SDA5B, SEG29

P47, SCL5B, SEG28

P45, SBT0B, SEG30

P42, SBT3B, SEG33

P61, DA_B, SEG18
P60, SEG19
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
SDA5A, NRE, SEG8, P73 76 50 P41, SBI3B, RXD3B, SEG34
SCL5A, NCS, SEG7, P74 77 49 P40, SBO3B, TXD3B, SEG35
SBO1B, TXD1B, A8, SEG6, P75 78 48 P36, SEG36
SBI1B, RXD1B, A9, SEG5, P76 79 47 P35, SBI4B, SEG37
SBT1B, A10, SEG4, P77 80 46 P34, SBT4B, SCL4B, SEG38
TM9OD0, SDO0, A11, SEG3, P80 81 45 P33, SBO4B, SDA4B, SEG39
TM9OD1, SDO1, A12, SEG2, P81 82 44 P32, SBT2B, SEG40
TM9OD2, SDO2, A13, SEG1, P82 83 43 P31, SBI2B, RXD2B, SEG41
TM9OD3, SDO3, A14, SEG0, P83 84 42 P30, SBO2B, TXD2B, SEG42
TM9OD4, SDO4, A15, COM0, P84 85 41 P16, TM8IOC, NBUZZERB, SEG43
TM9OD5, SDO5, A16, COM1, P85 86 40 P15, TM7IOC, BUZZERB, SEG44
SDO6, A17, COM2, P86 87 39 P14, TM4IOC, SEG45
SDO7, A18, COM3, P87 88 38 P13, TM3IOC, SEG46
A19, VLC3, P92 89 37 P12, TM1IOC, SEG47
NDK, VLC2, P93 90 36 P11, TM2IOC, SEG48
DA_C, VLC1, P94 91 35 P10, TM0IOC, RMOUTC, SEG49
DA_D, P95 92 34 P24, IRQ4, SEG50
AN15, PB7 93 33 P23, IRQ3, SEG51
AN14, PB6 94 32 P22, IRQ2, SEG52
AN13, PB5 95 31 P21, IRQ1, ACZ1, SEG53
AN12, PB4 96 30 P20, IRQ0, ACZ0, SEG54
AN11, PB3 97 29 P07, LED7, DA_A
AN10, PB2 98 28 P06, LED6, SBT3A
AN9, PB1 99 27 P05, LED5, SBI3A, RXD3A
AN8, PB0 100 26 P04, LED4, SBO3A, TXD3A
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9

VDD5
VREF+
MMOD

XO, P91
XI, P90
VSS
OSC1
OSC2

VDD18
P96
DMOD
LED0, TM7IOB, SBI1A, RXD1A, P00
LED1, TM8IOB, SBO1A, TXD1A, P01
LED2, TM9IOB, SBT1A, P02
LED3, TM0IOB, TM2IOB, RMOUTB, P03
NRST, P27
AN1, TM1IOA, PA1
AN2, TM2IOA, PA2
AN3, TM3IOA, PA3
AN4, TM4IOA, PA4
AN5, TM7IOA, PA5
AN6, TM8IOA, PA6
AN7, TM9IOA, PA7

ATRST
AN0, TM0IOA, RMOUTA, PA0

MAD00062FEM 117
 MN101E31 Series
Type MN101E31D MN101E31G MN101EF31D MN101EF31G
Internal ROM type Mask ROM FLASH
ROM (byte) 64K 128K 64K+8K 128K+4K
RAM (byte) 4K 6K 4K 6K
Package (Lead-free) LQFP080-P-1414A
50 ns 50 ns
Minimum Instruction 50 ns (at 2.2 V to 5.5 V, 20 MHz) (at 2.7 V to 5.5 V, 20 MHz) (at 2.2 V to 5.5 V, 20 MHz)
Execution Time *: at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used *: at internal 2 , 3 , 4 , 5 , 6 , *: at internal 2 , 3 , 4 , 5 , 6 ,
8 , 10 times oscillation used 8 , 10 times oscillation used

 Interrupts
6 external interrupts. 23 internal interrupts
RESET. NMI. External 0 to 4. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Time base. Serial 0 (2 systems). Serial 1 (2
systems). Serial 2 (2 systems). Serial 4. Serial 5. A/D conversion. ATC. Key interrupt

 Timer Counter
8-bit timer × 7
Timer 0 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Remote control carrier output. Simple
pulse width measurement. Real time output control
Timer 1 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 0, 1). Timer synchronous output
Timer 2 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Simple pulse width measurement. 24-bit
cascade connected (timer 0, 1, 2). Timer synchronous output. Real time output control
Timer 3 ..................Timer pulse output. Event count. Remote control carrier output. 16-bit cascade connected (timer 2, 3). 32-bit
cascade connected (timer 0, 1, 2, 3)
Timer 4 ..................Timer pulse output. Added pulse (2-bit) type PWM output. Event count. Serial transfer clock output. Simple pulse
width measurement
Timer 6 ..................8-bit freerun timer. Time base timer
Timer A..................Event count. Baud rate timer. Clock output for peripheral function
16-bit timer × 2
Timer 7 ..................Timer pulse output. Event count. High accuracy PWM. High performance IGBT output (cycle/duty continuous
variable). Timer synchronous output. Input capture (both edge available). Real time output control. Double buffer
compare register
Timer 8 ..................Timer pulse output. Event count. High accuracy PWM output (cycle/duty continuous variable). Pulse width
measurement. Input capture (both edge available). 32-bit cascade connected (timer 7, 8). 32-bit PWM output.
Synchronous output event. Double buffer compare register
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 3: Serial 0 to 2
Synchronous type/Multi-master I2C × 1: Serial 4
I2C slave × 1: Serial 5

 DMA controller
1 systems. Maximum transfer cycles are 255
Starting factor: External request. Internal event. Software

 I/O Pins
I/O 70 : Common use. Specified pull-up/pull-down resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 12 channels

 Display control function

LCD: 41 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty) 1/3 bias
Usable if VLC1 ≤ VDD

 Special Ports
Buzzer output. Inverted buzzer output. Remote control carrier output. High-current drive port

118 MAD00064GEM
 MN101E31D, MN101E31G, MN101EF31D, MN101EF31G

 ROM Correction
Correcting address designation: Up to 7 addresses possible

 Pin Assignment
LQFP080-P-1414A

P51, SBI0A, RXD0A, KEY1, D1, SEG20

P54, NBUZZERA, KEY4, D4, SEG23

P53, BUZZERA, KEY3, D3, SEG22
P70, SBO2A, TXD2A, A6, SEG11

P66, SBO4A, SDA4A, A4, SEG13

P71, SBI2A, RXD2A, A7, SEG10

P67, SBT4A, SCL4A, A5, SEG12

P52, SBT0A, KEY2, D2, SEG21

P64, TM4IOB, A2, SEG15
P63, TM3IOB, A1, SEG16
P62, TM1IOB, A0, SEG17
P72, SBT2A, NWE, SEG9
P73, SDA5A, NRE, SEG8

P65, SBI4A, A3, SEG14

P50, KEY0, D0, SEG19

P55, KEY5, D5, SEG24

P56, KEY6, D6, SEG25
P57, KEY7, D7, SEG26
P47, SCL5B, SEG27
P61, SEG18
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
SCL5A, NCS, SEG7, P74 61 40 P46, SDA5B, SEG28
SBO1B, TXD1B, A8, SEG6, P75 62 39 P45, SBT0B, SEG29
SBI1B, RXD1B, A9, SEG5, P76 63 38 P44, SBI0B, RXD0B, SEG30
SBT1B, A10, SEG4, P77 64 37 P43, SBO0B, TXD0B, SEG31
SDO0, A11, SEG3, P80 65 36 P35, SBI4B, SEG32
SDO1, A12, SEG2, P81 66 35 P34, SBT4B, SCL4B, SEG33
SDO2, A13, SEG1, P82 67 34 P33, SBO4B, SDA4B, SEG34
SDO3, A14, SEG0, P83 68 33 P10, TM0IOC, RMOUTC, SEG35
SDO4, A15, COM0, P84 69 32 P24, IRQ4, SEG36
SDO5, A16, COM1, P85 70 31 P23, IRQ3, SEG37
SDO6, A17, COM2, P86 71 30 P22, IRQ2, SEG38
SDO7, A18, COM3, P87 72 29 P21, IRQ1, ACZ1, SEG39
A19, VLC3, P92 73 28 P20, IRQ0, ACZ0, SEG40
NDK, VLC2, P93 74 27 P06, LED6
VLC1, P94 75 26 P05, LED5
P95 76 25 P04, LED4
AN11, PB3 77 24 P03, LED3, TM0IOB, TM2IOB, RMOUTB
AN10, PB2 78 23 P02, LED2, SBT1A
AN9, PB1 79 22 P01, LED1, TM8IOB, SBO1A, TXD1A
AN8, PB0 80 21 P00, LED0, TM7IOB, SBI1A, RXD1A
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9

VDD5
VREF+
MMOD

XO, P91
XI, P90
VSS
OSC1
OSC2

VDD18
DMOD
NRST, P27
AN1, TM1IOA, PA1
AN2, TM2IOA, PA2
AN3, TM3IOA, PA3
AN4, TM4IOA, PA4
AN5, TM7IOA, PA5
AN6, TM8IOA, PA6
AN7, PA7

ATRST
AN0, TM0IOA, RMOUTA, PA0

MAD00064GEM 119
 MN101E32 Series
Type MN101EF32D
Internal ROM type FLASH
ROM (byte) 64K+8K
RAM (byte) 4K
Package (Lead-free) LQFP064-P-1414
Minimum Instruction 50 ns (at 2.7 V to 5.5 V, 20 MHz)
Execution Time *: at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used

 Interrupts
6 external interrupts. 23 internal interrupts
RESET. NMI. External 0 to 4. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Time base. Serial 0 (2 systems). Serial 1 (2
systems). Serial 2 (2 systems). Serial 4. Serial 5. A/D conversion. ATC. Key interrupt

 Timer Counter
8-bit timer × 7
Timer 0 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Remote control carrier output. Simple
pulse width measurement. Real time output control
Timer 1 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 0, 1). Timer synchronous output
Timer 2 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Simple pulse width measurement. 24-bit
cascade connected (timer 0, 1, 2). Timer synchronous output. Real time output control
Timer 3 ..................Timer pulse output. Event count. Remote control carrier output. 16-bit cascade connected (timer 2, 3). 32-bit
cascade connected (timer 0, 1, 2, 3)
Timer 4 ..................Timer pulse output. Added pulse (2-bit) type PWM output. Event count. Serial transfer clock output. Simple pulse
width measurement
Timer 6 ..................8-bit freerun timer. Time base timer
Timer A..................Event count. Baud rate timer. Clock output for peripheral function
16-bit timer × 2
Timer 7 ..................Timer pulse output. Event count. High accuracy PWM. High performance IGBT output (cycle/duty continuous
variable). Timer synchronous output. Input capture (both edge available). Real time output control. Double buffer
compare register
Timer 8 ..................Timer pulse output. Event count. High accuracy PWM output (cycle/duty continuous variable). Pulse width
measurement. Input capture (both edge available). 32-bit cascade connected (timer 7, 8). 32-bit PWM output.
Synchronous output event. Double buffer compare register
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 3: Serial 0 to 2
Synchronous type/Multi-master I2C × 1: Serial 4
I2C slave × 1: Serial 5

 DMA controller
1 systems. Maximum transfer cycles are 255
Starting factor: External request. Internal event. Software

 I/O Pins
I/O 54 : Common use. Specified pull-up/pull-down resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 8 channels

 Display control function

LCD: 32 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty) 1/3 bias
Usable if VLC1 ≤ VDD

 Special Ports
Buzzer output. Inverted buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 7 addresses possible

120 MAD00066GEM
 MN101EF32D

 Pin Assignment
LQFP064-P-1414

P50, SEG18, KEY0, D0, SBO0A, TXD0A

P51, SEG19, KEY1, D1, SBI0A, RXD0A
P70, SEG11, A6, SBO2A, TXD2A

P66, SEG13, A4, SBO4A, SDA4A

P71, SEG10, A7, SBI2A, RXD2A

P67, SEG12, A5, SBT4A, SCL4A

P75, SEG6, A8, SBO1B, TXD1B
P76, SEG5, A9, SBI1B, RXD1B

P64, SEG15, A2, TM4IOB

P63, SEG16, A1, TM3IOB
P62, SEG17, A0, TM1IOB
P72, SEG9, NWE, SBT2A
P77, SEG4, A10, SBT1B

P65, SEG14, A3, SBI4A

P73, SEG8, NRE
P74, SEG7, NCS
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
SEG3, A11, SDO0, P80 49 32 P52, SBT0A, D2, KEY2, SEG20
SEG2, A12, SDO1, P81 50 31 P53, BUZZERA, D3, KEY3, SEG21
SEG1, A13, SDO2, P82 51 30 P54, NBUZZERA, D4, KEY4, SEG22
SEG0, A14, SDO3, P83 52 29 P55, D5, KEY5, SEG23
COM0, A15, SDO4, P84 53 28 P56, D6, KEY6, SEG24
COM1, A16, SDO5, P85 54 27 P57, D7, KEY7, SEG25
COM2, A17, SDO6, P86 55 26 P10, RMOUTC, TM0IOC, SEG26
COM3, A18, SDO7, P87 56 25 P24, IRQ4, SE27
VLC3, A19, P92 57 24 P23, IRQ3, SEG28
VLC2, NDK, P93 58 23 P22, IRQ2, SEG29
VLC1, P94 59 22 P21, ACZ1, IRQ1, SEG30
P95 60 21 P20, ACZ0, IRQ0, SEG31
AN0, TM0IOA, RMOUTA, PA0 61 20 P03, RMOUTB, TM2IOB, TM0IOB, LED3
AN1, TM1IOA, PA1 62 19 P02, SBT1A, LED2
AN2, TM2IOA, PA2 63 18 P01, TXD1A, SBO1A, TM8IOB, LED1
AN3, TM3IOA, PA3 64 17 P00, RXD1A, SBI1A, TM7IOB, LED0
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9

VDD5
VREF+
MMOD

XO, P91
XI, P90
VSS
OSC1
OSC2

VDD18
DMOD
NRST, P27
TM4IOA, AN4, PA4
TM7IOA, AN5, PA5
TM8IOA, AN6, PA6
AN7, PA7

ATRST

MAD00066GEM 121
 MN101E46 Series
Type MN101E46G MN101E46N MN101E46R MN101EF46R
Internal ROM type Mask ROM FLASH
ROM (byte) 128K 508K 928K
RAM (byte) 4K 6K 8K
TQFP128-P-1414A
TQFP128-P-1414C
Package (Lead-free) TQFP128-P-1414C (Under planning) (ES (Engineering Sample)
(Under development) available)
0.1 µs (at 2.2 V to 3.6 V, 10 MHz)
Minimum Instruction 0.125 µs (at 1.8 V to 3.6 V, 8 MHz)
Execution Time 61 µs (at 1.8 V to 3.6 V, 32.768 kHz)

 Interrupts
RESET. Watchdog. External 0 to 3. Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Time base. Serial 0. Serial 1 (2
systems). A/D conversion finish. Automatic transfer finish. LCD frame finish

 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement
Timer 1 ..................Square-wave output. Event count. Serial transfer clock output
Timer 2 ..................Square-wave/8-bit PWM output. Serial transfer clock output. Event count. Simple pulse width measurement
Timer 3 ..................Square-wave output. Event count. Serial transfer clock output
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7, 8 ..............Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Pulse width measurement.
Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/Single-master I2C × 1: Serial 0
Synchronous type/UART (full-duplex) × 1: Serial 1

 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 67 : Common use
Output 40 : LCD drive output exclusive use

 A/D converter
10-bit × 3 channels (External input 2 channels, Internal 1.8 V input 1 channel)

 Display control function

Dot Matrix type LCD control function
Display size up to 2048 pixels (32 COM × 64 SEG)
LCD drivers: COM output maximum 32 pins / SEG output maximum 67 pins (3 pins has dual function for COM/SEG)
1/8, 1/16, 1/24, 1/32 duty
1/5, 1/6 bias
LCD panel drive voltage maximum 5.5 V
Built-in LCD voltage booster and LCD voltage dividing resister
16-level contrast control
Bright and dark 2-step level display function
Monochrome inversion function

 Special Ports
Buzzer output. Remote control carrier output

122 MAD00072CEM
 MN101E46G, MN101E46N, MN101E46R, MN101EF46R

 ROM Correction
Correcting address designation: Up to 7 addresses possible

 Pin Assignment
TQFP128-P-1414C

P87, SEG32
P86, SEG33
P85, SEG34
P84, SEG35
P83, SEG36
P82, SEG37
P81, SEG38
P80, SEG39
P77, SEG40
P76, SEG41
P75, SEG42
P74, SEG43
P73, SEG44
P72, SEG45
P71, SEG46
P70, SEG47
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
SEG15 97 64 P67, SEG48
SEG14 98 63 P66, SEG49
SEG13 99 62 P65, SEG50
SEG12 100 61 P64, SEG51
SEG11 101 60 P63, SEG52
SEG10 102 59 P62, SEG53
SEG9 103 58 P61, SEG54
SEG8 104 57 P60, SEG55
SEG7 105 56 P57, SEG56, KEY15
SEG6 106 55 P56, SEG57, KEY14
SEG5 107 54 P55, SEG58, KEY13
SEG4 108 53 P54, SEG59, KEY12
SEG3 109 52 P53, SEG60, KEY11
SEG2 110 51 P52, SEG61, KEY10
SEG1 111 50 P51, SEG62, KEY9
SEG0 112 49 P50, SEG63, KEY8
COM0 113 48 P47, COM16, SEG64, NBUZB
COM1 114 47 P46, COM17, SEG65, BUZB
COM2 115 46 P45, COM18, SEG66, TM3IO
COM3 116 45 P44, COM19, TM2IO
COM4 117 44 P43, COM20, TM8IO
COM5 118 43 P42, COM21, SBT1A
COM6 119 42 P41, COM22, SBI1A, RXD1A
COM7 120 41 P40, COM23, SBO1A, TXD1A
COM8, P90 121 40 P37, COM24, KEY7
COM9, P91 122 39 P36, COM25, KEY6
COM10, P92 123 38 P35, COM26, KEY5
COM11, P93 124 37 P34, COM27, KEY4
COM12, P94 125 36 P33, COM28, KEY3
COM13, P95 126 35 P32, COM29, KEY2
COM14, P96 127 34 P31, COM30, KEY1
COM15, P97 128 33 P30, COM31, KEY0
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
11
1
2
3
4
5
6
7
8
9

DMOD
VL1
VL2
VL3
VL4
VL5
C1
C2
C3

VDD18
VDD
OSC2
OSC1
VSS
XI
XO

MMOD

VREF+

NBUZA, AN1, P01

TXD1B, SBO1B, TM0IO, P02
SBT1B, TM1IO, P03
RXD1B, SBI1B, TM7IO, P04
SDA, SBO0, P05
SBI0, P06
SCL, SBT0, P07
IRQ0, P20
ACZ, IRQ1, P21
IRQ2, P22
NRST, P27

RMOUT, BUZA, AN0, P00

ATRST
VLIN

MAD00072CEM 123
 MN101E56 Series
Type MN101EF56G
Internal ROM type FLASH
ROM (byte) 128K
RAM (byte) 6K
Package (Lead-free) LQFP100-P-1414 (Under planning), QFP100-P-1818B (Under development)
50 ns (at 2.7 V to 5.5 V, 20 MHz)
Minimum Instruction 125 ns (at 1.8 V to 5.5 V, 8 MHz)
Execution Time *: at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used

 Interrupts
5 external interrupts. 29 internal interrupts
RESET. NMI. External 0 to 4. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Timer 9 (3 systems). Time base. 24H
timer. Alarm. Serial 0 (2 systems). Serial 1 (2 systems). Serial 2 (2 systems). Serial 4 (2 systems). LIN. A/D conversion. ATC. Key
interrupt. Low voltage detection

 Timer Counter
8-bit timer × 7
Timer 0 ..................Timer pulse output. Added pulse(2-bit)type PWM output to large current terminal TM0IOB possible. Event count.
Simple pulse width measurement
Timer 1 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 0, 1). Timer synchronous output
Timer 2 ..................Timer pulse output. Added pulse(2-bit)type PWM output to large current terminal TM2IOB possible. Event count.
Simple pulse width measurement. 24-bit cascade connected (timer 0, 1, 2). Timer synchronous output
Timer 3 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 2, 3). 32-bit cascade connected (timer 0, 1, 2, 3)
Timer 4 ..................Timer pulse output. Added pulse (2-bit) type PWM output. Event count. Simple pulse width measurement
Timer 6 ..................8-bit freerun timer
Timer A..................Baud rate timer. Clock output for peripheral function
16-bit timer × 3
Timer 7 ..................Timer pulse output to large current terminal TM7IOB possible. Event count. High accuracy PWM/IGBT output
(cycle/duty continuous variable). Pulse width measurement. Timer synchronous output. Input capture (both edge
available). Real time output control. Double buffer compare register
Timer 8 ..................Timer pulse output to large current terminal TM8IOB possible. Event count. High accuracy PWM output
(cycle/duty continuous variable). Pulse width measurement. Input capture (both edge available). 32-bit cascade
connected (timer 7, 8). 32-bit PWM output. Synchronous output event. Double buffer compare register
Timer 9 ..................Timer pulse output to large current terminal TM9IOB possible. 3-phase PWM output. Triangular waveform
output. Jigsaw waveform output. Dead time setup. Event count
24H timer: Interval function (Interruption every 0.5 seconds, every 1 second, every 1 minute, every 1 hour and 24 hours). Alarm function
Time base timer: One-minute count setting
Watchdog timer × 2

 Serial interface
Synchronous type/UART (full-duplex)/LIN × 1: Serial 0
Synchronous type/UART (full-duplex) × 2: Serial 1, 2
Synchronous type/Multi-master I2C × 1: Serial 4

 DMA controller
1 systems. Maximum transfer cycles are 255
Starting factor: External request. Internal event. Software

 I/O Pins
I/O 90 : Common use. Specified pull-up/pull-down resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 24 channels

 D/A converter
8-bit × 2 channels

 Display control function

LCD: 55 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
Usable if VLC1 ≤ VDD

124 MAD00079AEM
 MN101EF56G

 Special Ports
Buzzer output. Inverted buzzer output. High-current drive port

 Reset
Low voltage detection. Automatic Reset. Reset factor detection

 Internal oscillation
High speed: 20 MHz/16 MHz. Low speed: 30 kHz

 Pin Assignment
LQFP100-P-1414, QFP100-P-1818B

P50, SEG16, SBO1A, TXD1A

P65, SEG11, SBO2A, TXD2A

P43, SEG28, SBO0B, TXD0B

P51, SEG17, SBI1A, RXD1A

P66, SEG10, SBI2A, RXD2A

P44, SEG27, SBI0B, RXD0B

P56, SEG22, NBUZZERA

P70, SEG8, KEY0, SBI4A

P57, SEG23, BUZZERA

P62, SEG14, TM1IOB

P63, SEG13, TM3IOB
P64, SEG12, TM4IOB
P52, SEG18, SBT1A
P45, SEG26, SBT0B

P61, SEG15, DC_C

P67, SEG9, SBT2A

P36, SEG32
P40, SEG31
P41, SEG30
P42, SEG29

P46, SEG25
P47, SEG24

P55, SEG21
P54, SEG20
P53, SEG19
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
SBI4B, SEG33, P35 76 50 P71, SEG7, KEY1, SBO4A, SDA4A
SCL4B, SBT4B, SEG34, P34 77 49 P72, SEG6, KEY2, SBT4A, SCL4A
SDA4B, SBO4B, SEG35, P33 78 48 P73, SEG5, KEY3
SBT2B, SEG36, P32 79 47 P74, SEG4, KEY4
RXD2B, SBI2B, SEG37, P31 80 46 P75, SEG3, KEY5, SBO1B, TXD1B
TXD2B, SBO2B, SEG38, P30 81 45 P76, SEG2, KEY6, SBI1B, RXD1B
NBUZZERB, TM8IOC, SEG39, P16 82 44 P77, SEG1, KEY7, SBT1B
BUZZERB, TM7IOC, SEG40, P15 83 43 P80, SEG0, SDO0, TM9OD0
TM4IOC, SEG41, P14 84 42 P81, COM0, SDO1, TM9OD1
TM3IOC, AN23, SEG42, P13 85 41 P82, COM1, SDO2, TM9OD2
TM1IOC, AN22, SEG43, P12 86 40 P83, COM2, SDO3, TM9OD3
TM2IOC, AN21, SEG44, P11 87 39 P84, COM3, SDO4, TM9OD4
TM0IOC, AN20, SEG45, P10 88 38 P85, VLC3, SDO5, TM9OD5
AN19, SEG46, P92 89 37 P86, VLC2, SDO6
AN18, SEG47, P93 90 36 P87, VLC1, SDO7
DA_B, AN17, SEG48, P94 91 35 P24, IRQ4
DA_A, AN16, SEG49, P95 92 34 P23, IRQ3
AN15, SEG50, PB7 93 33 P22, IRQ2
AN14, SEG51, PB6 94 32 P21, IRQ1, ACZ1
AN13, SEG52, PB5 95 31 P20, IRQ0, ACZ0
AN12, SEG53, PB4 96 30 P07, LED7, DA_D
AN11, SEG54, PB3 97 29 P06, LED6
AN10, PB2 98 28 P05, LED5
AN9, PB1 99 27 P04, LED4, TM0IOB, TM2IOB, SBT0A
AN8, PB0 100 26 P03, LED3, TM8IOB, SBO0A, TXD0A
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9

VDD5
VREF+

XI, P90
XO, P91
VSS
OSC1, P25
OSC2, P26

MMOD
VDD18
DMOD
RON
VSS

OCD_CLK, TM9IOB, LED1, P01

RXD0A, SBI0A, TM7IOB, LED2, P02
NRST, P27
TM0IOA, AN0, PA0
TM1IOA, AN1, PA1
TM2IOA, AN2, PA2
TM3IOA, AN3, PA3
TM4IOA, AN4, PA4
TM7IOA, AN5, PA5
TM8IOA, AN6, PA6
TM9IOA, AN7, PA7

ATRST

OCD_DATA, LED0, P00

MAD00079AEM 125
 MN101E57 Series
Type MN101EF57G
Internal ROM type FLASH
ROM (byte) 128K
RAM (byte) 6K
Package (Lead-free) LQFP080-P-1414A (Under development), TQFP080-P-1212D (Under planning)
50 ns (at 2.7 V to 5.5 V, 20 MHz)
Minimum Instruction 125 ns (at 1.8 V to 5.5 V, 8 MHz)
Execution Time *: at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used

 Interrupts
5 external interrupts. 29 internal interrupts
RESET. NMI. External 0 to 4. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Timer 9 (3 systems). Time base. 24H
timer. Alarm. Serial 0 (2 systems). Serial 1 (2 systems). Serial 2 (2 systems). Serial 4 (2 systems). LIN. A/D conversion. ATC. Key
interrupt. Low voltage detection

 Timer Counter
8-bit timer × 7
Timer 0 ..................Timer pulse output. Added pulse(2-bit)type PWM output to large current terminal TM0IOB possible. Event count.
Simple pulse width measurement
Timer 1 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 0, 1). Timer synchronous output
Timer 2 ..................Timer pulse output. Added pulse(2-bit)type PWM output to large current terminal TM2IOB possible. Event count.
Simple pulse width measurement. 24-bit cascade connected (timer 0, 1, 2). Timer synchronous output
Timer 3 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 2, 3). 32-bit cascade connected (timer 0, 1, 2, 3)
Timer 4 ..................Timer pulse output. Added pulse (2-bit) type PWM output. Event count. Simple pulse width measurement
Timer 6 ..................8-bit freerun timer
Timer A..................Baud rate timer. Clock output for peripheral function
16-bit timer × 3
Timer 7 ..................Timer pulse output to large current terminal TM7IOB possible. Event count. High accuracy PWM/IGBT output
(cycle/duty continuous variable). Pulse width measurement. Timer synchronous output. Input capture (both edge
available). Real time output control. Double buffer compare register
Timer 8 ..................Timer pulse output to large current terminal TM8IOB possible. Event count. High accuracy PWM output
(cycle/duty continuous variable). Pulse width measurement. Input capture (both edge available). 32-bit cascade
connected (timer 7, 8). 32-bit PWM output. Synchronous output event. Double buffer compare register
Timer 9 ..................Timer pulse output to large current terminal TM9IOB possible. 3-phase PWM output. Triangular waveform
output. Jigsaw waveform output. Dead time setup. Event count
24H timer: Interval function (Interruption every 0.5 seconds, every 1 second, every 1 minute, every 1 hour and 24 hours). Alarm function
Time base timer: One-minute count setting
Watchdog timer × 2

 Serial interface
Synchronous type/UART (full-duplex)/LIN × 1: Serial 0
Synchronous type/UART (full-duplex) × 2: Serial 1, 2
Synchronous type/Multi-master I2C × 1: Serial 4

 DMA controller
1 systems. Maximum transfer cycles are 255
Starting factor: External request. Internal event. Software

 I/O Pins
I/O 70 : Common use. Specified pull-up/pull-down resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 16 channels

 D/A converter
8-bit × 2 channels

 Display control function

LCD: 41 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
Usable if VLC1 ≤ VDD

126 MAD00080AEM
 MN101EF57G

 Special Ports
Buzzer output. Inverted buzzer output. High-current drive port

 Reset
Low voltage detection. Automatic Reset. Reset factor detection

 Internal oscillation
High speed: 20 MHz/16 MHz. Low speed: 30 kHz

 Pin Assignment
LQFP100-P-1414

P71, SEG7, KEY1, SBO4A, SDA4A

P75, SEG3, KEY5, SBO1B, TXD1B

P72, SEG6, KEY2, SBT4A, SCL4A

P76, SEG2, KEY6, SBI1B, RXD1B

P50, SEG15, SBO1A, TXD1A

P65, SEG11, SBO2A, TXD2A

P81, COM0, SDO1, TM9OD1

P82, COM1, SDO2, TM9OD2
P51, SEG16, SBI1A, RXD1A

P66, SEG10, SBI2A, RXD2A

P80, SEG0, SDO0, TM9OD0

P77, SEG1, KEY7, SBT1B
P70, SEG8, KEY0, SBI4A
P62, SEG14, TM1IOB
P63, SEG13, TM3IOB
P64, SEG12, TM4IOB
P52, SEG17, SBT1A

P67, SEG9, SBT2A

P73, SEG5, KEY3

P74, SEG4, KEY4
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
SEG18, P53 61 40 TM9OD3, SDO3, COM2, P83
SEG19, P54 62 39 P84, COM3, SDO4, TM9OD4
SEG20, P55 63 38 P85, VLC3, SDO5, TM9OD5
NBUZZERA, SEG21, P56 64 37 P86, VLC2, SDO6
BUZZERA, SEG22, P57 65 36 P87, VLC1, SDO7
SEG23, P47 66 35 P24, IRQ4
SEG24, P46 67 34 P23, IRQ3
SBT0B, SEG25, P45 68 33 P22, IRQ2
RXD0B, SBI0B, SEG26, P44 69 32 P21, IRQ1, ACZ1
TXD0B, SBO0B, SEG27, P43 70 31 P20, IRQ0, ACZ0
SBI4B, SEG28, P35 71 30 P07, LED7, DA_B
SCL4B, SBT4B, SEG29, P34 72 29 P06, LED6
SDA4B, SBO4B, AN15, SEG30, P33 73 28 P05, LED5
AN14, SEG31, P92 74 27 P04, LED4, TM0IOB, TM2IOB, SBT0A
AN13, SEG32, P93 75 26 P03, LED3, TM8IOB, SBO0A, TXD0A
DA_A, AN12, SEG33, P94 76 25 P02, LED2, TM7IOB, SBI0A, RXD0A
AN11, SEG34, PB3 77 24 P01, LED1, TM9IOB, OCD_CLK
AN10, SEG35, PB2 78 23 P00, LED0, OCD_DATA
AN9, SEG36, PB1 79 22 VSS
AN8, SEG37, PB0 80 21 RON
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9

VDD5
XI, P90
XO, P91
VSS
OSC1, P25
OSC2, P26

MMOD
VDD18
DMOD
Vref+

NRST, P27
TM0IOA, AN0, SEG38, PA0
TM1IOA, AN1, SEG39, PA1
TM2IOA, AN2, SEG40, PA2
TM3IOA, AN3, PA3
TM4IOA, AN4, PA4
TM7IOA, AN5, PA5
TM8IOA, AN6, PA6
TM9IOA, AN7, PA7

ATRST

MAD00080AEM 127
 MN101E58 Series
Type MN101EF58G
Internal ROM type FLASH
ROM (byte) 128K
RAM (byte) 6K
Package (Lead-free) LQFP064-P-1414 (Under planning), TQFP064-P-1010C (Under development)
50 ns (at 2.7 V to 5.5 V, 20 MHz)
Minimum Instruction 125 ns (at 1.8 V to 5.5 V, 8 MHz)
Execution Time *: at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used

 Interrupts
5 external interrupts. 29 internal interrupts
RESET. NMI. External 0 to 4. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Timer 9 (3 systems). Time base. 24H
timer. Alarm. Serial 0 (2 systems). Serial 1 (2 systems). Serial 2 (2 systems). Serial 4 (2 systems). LIN. A/D conversion. ATC. Key
interrupt. Low voltage detection

 Timer Counter
8-bit timer × 7
Timer 0 ..................Timer pulse output. Added pulse(2-bit)type PWM output to large current terminal TM0IOB possible. Event count.
Simple pulse width measurement
Timer 1 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 0, 1). Timer synchronous output
Timer 2 ..................Timer pulse output. Added pulse(2-bit)type PWM output to large current terminal TM2IOB possible. Event count.
Simple pulse width measurement. 24-bit cascade connected (timer 0, 1, 2). Timer synchronous output
Timer 3 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 2, 3). 32-bit cascade connected (timer 0, 1, 2, 3)
Timer 4 ..................Timer pulse output. Added pulse (2-bit) type PWM output. Event count. Simple pulse width measurement
Timer 6 ..................8-bit freerun timer
Timer A..................Baud rate timer. Clock output for peripheral function
16-bit timer × 3
Timer 7 ..................Timer pulse output to large current terminal TM7IOB possible. Event count. High accuracy PWM/IGBT output
(cycle/duty continuous variable). Pulse width measurement. Timer synchronous output. Input capture (both edge
available). Real time output control. Double buffer compare register
Timer 8 ..................Timer pulse output to large current terminal TM8IOB possible. Event count. High accuracy PWM output
(cycle/duty continuous variable). Pulse width measurement. Input capture (both edge available). 32-bit cascade
connected (timer 7, 8). 32-bit PWM output. Synchronous output event. Double buffer compare register
Timer 9 ..................Timer pulse output to large current terminal TM9IOB possible. 3-phase PWM output. Triangular waveform
output. Jigsaw waveform output. Dead time setup. Event count
24H timer: Interval function (Interruption every 0.5 seconds, every 1 second, every 1 minute, every 1 hour and 24 hours). Alarm function
Time base timer: One-minute count setting
Watchdog timer × 2

 Serial interface
Synchronous type/UART (full-duplex)/LIN × 1: Serial 0
Synchronous type/UART (full-duplex) × 2: Serial 1, 2
Synchronous type/Multi-master I2C × 1: Serial 4

 DMA controller
1 systems. Maximum transfer cycles are 255
Starting factor: External request. Internal event. Software

 I/O Pins
I/O 54 : Common use. Specified pull-up/pull-down resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 12 channels

 Display control function

LCD: 32 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
Usable if VLC1 ≤ VDD

128 MAD00081AEM
 MN101EF58G

 Special Ports
Buzzer output. Inverted buzzer output. High-current drive port

 Reset
Low voltage detection. Automatic Reset. Reset factor detection

 Internal oscillation
High speed: 20 MHz/16 MHz. Low speed: 30 kHz

 Pin Assignment
LQFP064-P-1414, TQFP064-P-1010C

P71, SEG7, KEY1, SBO4A, SDA4A

P75, SEG3, KEY5, SBO1B, TXD1B

P72, SEG6, KEY2, SBT4A, SCL4A

P76, SEG2, KEY6, SBI1B, RXD1B

TXD2A, SBO2A, SEG11, P65

P81, COM0, SDO1, TM9OD1

P82, COM1, SDO2, TM9OD2
P83, COM2, SDO3, TM9OD3
P84, COM3, SDO4, TM9OD4
P66, SEG10, SBI2A, RXD2A

P80, SEG0, SDO0, TM9OD0

P77, SEG1, KEY7, SBT1B
P70, SEG8, KEY0, SBI4A
P67, SEG9, SBT2A

P73, SEG5, KEY3

P74, SEG4, KEY4
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
TM4IOB, SEG12, P64 49 32 TM9OD5, SDO5, VLC3, P85
TM3IOB, SEG13, P63 50 31 P86, VLC2, SDO6
TM1IOB, SEG14, P62 51 30 P87, VLC1, SDO7
TXD1A, SBO1A, SEG15, P50 52 29 P24, IRQ4
RXD1A, SBI1A, SEG16, P51 53 28 P23, IRQ3
SBT1A, SEG17, P52 54 27 P22, IRQ2
SEG18, P53 55 26 P21, IRQ1, ACZ1
SEG19, P54 56 25 P20, IRQ0, ACZ0
AN11, SEG20, P55 57 24 P05, LED5
NBUZZERA, AN10, SEG21, P56 58 23 P04, LED4, TM0IOB, TM2IOB, SBT0A
BUZZERA, AN9, SEG22, P57 59 22 P03, LED3, TM8IOB, SBO0A, TXD0A
AN8, SEG23, P94 60 21 P02, LED2, TM7IOB, SBI0A, RXD0A
TM0IOA, AN0, SEG24, PA0 61 20 P01, LED1, TM9IOB, OCD_CLK
TM1IOA, AN1, SEG25, PA1 62 19 P00, LED0, OCD_DATA
TM2IOA, AN2, SEG26, PA2 63 18 VSS
TM3IOA, AN3, SEG27, PA3 64 17 RON
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9

VDD5
VREF+

XI, P90
XO, P91
VSS
OSC1, P25
OSC2, P26

MMOD
VDD18
DMOD
NRST, P27
TM4IOA, AN4, SEG28, PA4
TM7IOA, AN5, SEG29, PA5
TM8IOA, AN6, SEG30, PA6
TM9IOA, AN7, SEG31, PA7

ATRST

MAD00081AEM 129
 MN101E30 Series
Type MN101E30N MN101E30R MN101EF30R
Internal ROM type Mask ROM FLASH
ROM (byte) 508K 928K
RAM (byte) 8K
Package (Lead-free) QFP100-P-1818B
Minimum Instruction 50 ns (at 2.2 V to 5.5 V, 20 MHz)
Execution Time *: at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used

 Interrupts
6 external interrupts. 30 internal interrupts
RESET. NMI. External 0 to 4. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Timer 9 (2 systems). Time base. Serial
0 (2 systems). Serial 1 (2 systems). Serial 2 (2 systems). Serial 3 (2 systems). Serial 4. Serial 5. A/D conversion. Automatic transfer (2
systems). Key interrupt. End of single tone. End of phrase

 Timer Counter
8-bit timer × 7
Timer 0 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Remote control carrier output. Simple
pulse width measurement. Real time output control
Timer 1 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 0, 1). Timer synchronous output
Timer 2 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Simple pulse width measurement. 24-bit
cascade connected (timer 0, 1, 2). Timer synchronous output. Real time output control
Timer 3 ..................Timer pulse output. Event count. Remote control carrier output. 16-bit cascade connected (timer 2, 3). 32-bit
cascade connected (timer 0, 1, 2, 3)
Timer 4 ..................Timer pulse output. Added pulse (2-bit) type PWM output. Event count. Serial transfer clock output. Simple pulse
width measurement
Timer 6 ..................8-bit freerun timer. Time base timer
Timer A..................Event count. Baud rate timer. Clock output for peripheral function
16-bit timer × 3
Timer 7 ..................Timer pulse output. Event count. High accuracy PWM. High performance IGBT output (cycle/duty continuous
variable). Timer synchronous output. Input capture (both edge available). Real time output control. Double buffer
compare register
Timer 8 ..................Timer pulse output. Event count. High accuracy PWM output (cycle/duty continuous variable). Pulse width
measurement. Input capture (both edge available). 32-bit cascade connected (timer 7, 8). 32-bit PWM output.
Synchronous output event. Double buffer compare register
Timer 9 ..................Timer pulse output. Event count. High accuracy PWM output (cycle/duty continuous variable). Pulse width
measurement. Input capture (both edge available). Real time output control. Double buffer compare register
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 4: Serial 0 to 3
Synchronous type/Multi-master I2C × 1: Serial 4
I2C slave × 1: Serial 5

 DMA controller
2 systems. Maximum transfer cycles are 255
Starting factor: External request. Internal event. Software

 I/O Pins
I/O 85 : Common use. Specified pull-up/pull-down resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 12 channels

 D/A converter
8-bit × 4 channels. 20-bit × 2 channels. (Sound reproduction:digital output, analog output)

 Display control function

LCD: 55 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty) 1/3 bias
Usable if VLC1 ≤ VDD

130 MAD00063FEM
 MN101E30N, MN101E30R, MN101EF30R

 Special Ports
Buzzer output. Inverted buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 7 addresses possible

 Pin Assignment
QFP100-P-1818B

P50, SBO0A, TXD0A, KEY0, D0

P51, SBI0A, RXD0A, KEY1, D1

P54, NBUZZERA, KEY4, D4

P53, BUZZERA, KEY3, D3
P70, SBO2A, TXD2A, A6

P66, SBO4A, SDA4A, A4

P71, SBI2A, RXD2A, A7

P67, SBT4A, SCL4A, A5

P52, SBT0A, KEY2, D2

P43, SBO0B, TXD0B

P44, SBI0B, RXD0B
P72, SBT2A, NWE

P64, TM4IOB, A2
P63, TM3IOB, A1
P62, TM1IOB, A0
P65, SBI4A, A3

P55, KEY5, D5
P56, KEY6, D6
P57, KEY7, D7

P46, SDA5B
P47, SCL5B

P45, SBT0B

P42, SBT3B
P61, DA_B
P60
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
SDA5A, NRE, P73 76 50 P41, SBI3B, RXD3B
SCL5A, NCS, P74 77 49 P40, SBO3B, TXD3B
SBO1B, TXD1B, A8, P75 78 48 P36
SBI1B, RXD1B, A9, P76 79 47 P35, SBI4B
SBT1B, A10, P77 80 46 P34, SBT4B, SCL4B
TM9OD0, PWM00, SDO0, A11, P80 81 45 P33, SBO4B, SDA4B
TM9OD1, PWMN00, SDO1, A12, P81 82 44 P32, SBT2B
TM9OD2, PWM01, SDO2, A13, P82 83 43 P31, SBI2B, RXD2B
TM9OD3, PWMN01, SDO3, A14, P83 84 42 P30, SBO2B, TXD2B
TM9OD4, PWM02, SDO4, A15, P84 85 41 P16, TM8IOC, NBUZZERB
TM9OD5, PWMN02, SDO5, A16, P85 86 40 P15, TM7IOC, BUZZERB
SDO6, A17, P86 87 39 P14, TM4IOC
SDO7, A18, P87 88 38 P13, TM3IOC
A19, P92 89 37 P12, TM1IOC
NDK, P93 90 36 P11, TM2IOC
DA_C, P94 91 35 P10, TM0IOC, RMOUTC
DA_D, P95 92 34 P24, IRQ4
AVDD 93 33 P23, IRQ3
DA1_DOUT 94 32 P22, IRQ2
DA1_AOUT 95 31 P21, IRQ1, ACZ1
AVSS 96 30 P20, IRQ0, ACZ0
AN11, PB3 97 29 P07, LED7, DA_A
AN10, PB2 98 28 P06, LED6, SBT3A
AN9, PB1 99 27 P05, LED5, SBI3A, RXD3A
AN8, PB0 100 26 P04, LED4, SBO3A, TXD3A
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9

VDD5
VREF+
MMOD

XO, P91
XI, P90
VSS
OSC1
OSC2

VDD18
N.C. (VDD33)
DMOD
LED0, TM7IOB, SBI1A, RXD1A, P00
LED1, TM8IOB, SBO1A, TXD1A, P01
LED2, TM9IOB, SBT1A, P02
LED3, TM0IOB, TM2IOB, RMOUTB, P03
NRST, P27
AN1, TM1IOA, PA1
AN2, TM2IOA, PA2
AN3, TM3IOA, PA3
AN4, TM4IOA, PA4
AN5, TM7IOA, PA5
AN6, TM8IOA, PA6
AN7, TM9IOA, PA7

ATRST
AN0, TM0IOA, RMOUTA, PA0

Note) ( ): Flash memory built-in type

MAD00063FEM 131
 MN101E59 Series
Type MN101E59R MN101EF59R
Internal ROM type Mask ROM FLASH
ROM (byte) 928K
RAM (byte) 8K
Package (Lead-free) QFP100-P-1818B
Minimum Instruction 50 ns (at 2.2 V to 5.5 V, 20 MHz)
Execution Time *: at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used

 Interrupts
6 external interrupts. 30 internal interrupts
RESET. NMI. External 0 to 4. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Timer 9 (2 systems). Time base. Serial
0 (2 systems). Serial 1 (2 systems). Serial 2 (2 systems). Serial 3 (2 systems). Serial 4. Serial 5. A/D conversion. Automatic transfer (2
systems). Key interrupt. End of single tone. End of phrase

 Timer Counter
8-bit timer × 7
Timer 0 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Remote control carrier output. Simple
pulse width measurement. Real time output control
Timer 1 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 0, 1). Timer synchronous output
Timer 2 ..................Timer pulse output. Event count. Added pulse (2-bit) type PWM output. Simple pulse width measurement. 24-bit
cascade connected (timer 0, 1, 2). Timer synchronous output. Real time output control
Timer 3 ..................Timer pulse output. Event count. Remote control carrier output. 16-bit cascade connected (timer 2, 3). 32-bit
cascade connected (timer 0, 1, 2, 3)
Timer 4 ..................Timer pulse output. Added pulse (2-bit) type PWM output. Event count. Serial transfer clock output. Simple pulse
width measurement
Timer 6 ..................8-bit freerun timer. Time base timer
Timer A..................Event count. Baud rate timer. Clock output for peripheral function
16-bit timer × 3
Timer 7 ..................Timer pulse output. Event count. High accuracy PWM. High performance IGBT output (cycle/duty continuous
variable). Timer synchronous output. Input capture (both edge available). Real time output control. Double buffer
compare register
Timer 8 ..................Timer pulse output. Event count. High accuracy PWM output (cycle/duty continuous variable). Pulse width
measurement. Input capture (both edge available). 32-bit cascade connected (timer 7, 8). 32-bit PWM output.
Synchronous output event. Double buffer compare register
Timer 9 ..................Timer pulse output. Event count. High accuracy PWM output (cycle/duty continuous variable). Pulse width
measurement. Input capture (both edge available). Real time output control. Double buffer compare register
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 4: Serial 0 to 3
Synchronous type/Multi-master I2C × 1: Serial 4
I2C slave × 1: Serial 5

 DMA controller
2 systems. Maximum transfer cycles are 255
Starting factor: External request. Internal event. Software

 I/O Pins
I/O 85 : Common use. Specified pull-up/pull-down resistor available. Input/output selectable (bit unit)

 A/D converter
10-bit × 12 channels

 D/A converter
8-bit × 4 channels. 20-bit × 2 channels. (Sound reproduction:digital output, analog output)

132 MAD00078BEM
 MN101E59R, MN101EF59R

 Display control function

LCD: 55 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty) 1/3 bias
Usable if VLC1 ≤ VDD

 Special Ports
Buzzer output. Inverted buzzer output. Remote control carrier output. High-current drive port

 ROM Correction
Correcting address designation: Up to 7 addresses possible

 Pin Assignment
QFP100-P-1818B

P50, SBO0A, TXD0A, KEY0, D0

P51, SBI0A, RXD0A, KEY1, D1

P54, NBUZZERA, KEY4, D4

P53, BUZZERA, KEY3, D3
P70, SBO2A, TXD2A, A6

P66, SBO4A, SDA4A, A4

P71, SBI2A, RXD2A, A7

P67, SBT4A, SCL4A, A5

P52, SBT0A, KEY2, D2

P43, SBO0B, TXD0B

P44, SBI0B, RXD0B
P72, SBT2A, NWE

P64, TM4IOB, A2
P63, TM3IOB, A1
P62, TM1IOB, A0
P65, SBI4A, A3

P55, KEY5, D5
P56, KEY6, D6
P57, KEY7, D7

P46, SDA5B
P47, SCL5B

P45, SBT0B

P42, SBT3B
P61, DA_B
P60
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
SDA5A, NRE, P73 76 50 P41, SBI3B, RXD3B
SCL5A, NCS, P74 77 49 P40, SBO3B, TXD3B
SBO1B, TXD1B, A8, P75 78 48 P36
SBI1B, RXD1B, A9, P76 79 47 P35, SBI4B
SBT1B, A10, P77 80 46 P34, SBT4B, SCL4B
TM9OD0, PWM00, SDO0, A11, P80 81 45 P33, SBO4B, SDA4B
TM9OD1, PWMN00, SDO1, A12, P81 82 44 P32, SBT2B
TM9OD2, PWM01, SDO2, A13, P82 83 43 P31, SBI2B, RXD2B
TM9OD3, PWMN01, SDO3, A14, P83 84 42 P30, SBO2B, TXD2B
TM9OD4, PWM02, SDO4, A15, P84 85 41 P16, TM8IOC, NBUZZERB
TM9OD5, PWMN02, SDO5, A16, P85 86 40 P15, TM7IOC, BUZZERB
SDO6, A17, P86 87 39 P14, TM4IOC
SDO7, A18, P87 88 38 P13, TM3IOC
A19, P92 89 37 P12, TM1IOC
NDK, P93 90 36 P11, TM2IOC
DA_C, P94 91 35 P10, TM0IOC, RMOUTC
DA_D, P95 92 34 P24, IRQ4
AVDD 93 33 P23, IRQ3
DA1_DOUT 94 32 P22, IRQ2
DA1_AOUT 95 31 P21, IRQ1, ACZ1
AVSS 96 30 P20, IRQ0, ACZ0
AN11, PB3 97 29 P07, LED7, DA_A
AN10, PB2 98 28 P06, LED6, SBT3A
AN9, PB1 99 27 P05, LED5, SBI3A, RXD3A
AN8, PB0 100 26 P04, LED4, SBO3A, TXD3A
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9

VDD5
VREF+
MMOD

XO, P91
XI, P90
VSS
OSC1
OSC2

VDD18
N.C. (VDD33)
DMOD
LED0, TM7IOB, SBI1A, RXD1A, P00
LED1, TM8IOB, SBO1A, TXD1A, P01
LED2, TM9IOB, SBT1A, P02
LED3, TM0IOB, TM2IOB, RMOUTB, P03
NRST, P27
AN1, TM1IOA, PA1
AN2, TM2IOA, PA2
AN3, TM3IOA, PA3
AN4, TM4IOA, PA4
AN5, TM7IOA, PA5
AN6, TM8IOA, PA6
AN7, TM9IOA, PA7

ATRST
AN0, TM0IOA, RMOUTA, PA0

Note) ( ): Flash memory built-in type

MAD00078BEM 133
 MN101E41 Series
Type MN101EF41N
Internal ROM type FLASH
ROM (byte) 512K
RAM (byte) 30K
Package (Lead-free) QFP100-P-1818B (Under planning)
Minimum Instruction 0.05 µs (at 3.0 V to 3.6 V, 20 MHz)
Execution Time

 Interrupts
RESET. Watchdog. External 0 to 5. Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer A to E. Time base. Serial 0 (2 systems). Serial 1 (2
systems). Serial 2. Serial 3 (2 systems). Serial 4 (2 systems). Automatic transfer finish (2 systems). A/D conversion finish. Key interrupt.
CAN controler

 Timer Counter
8-bit timer × 10
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Real time output control
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event. Pulse width measurement. Real time
output control. Serial baud rate timer
Timer 3 ..................Square-wave output. Event count. Serial baud rate timer
Timer 6 ..................8-bit freerun timer. Time base timer
Timer A, B, C, D, E
Timer 0, 1 can be cascade-connected
Timer 0, 1, 2 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 0, 1, 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
width measurement. Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 3: Serial 0, 1, 4
Synchronous type/Single-master I2C × 1: Serial 2
Synchronous type/I2C × 1: Serial 3

 CAN controller
Number of channels: 1 channels
CAN Protocol Specification Version: CAN2.0B
Transmission speed: Max. 1 Mbps
Data length code: 0 byte to 8 bytes
Message frame types: Standard and extended frame format supported
Standard (SFF) ID: 11-bit. Extended (EFF) ID: 29-bit
Buffer size (each channel): 32 (transmission/reception)

 DMA controller
Number of channels: 2 channels
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 22 : (5 V I/F port) Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
62 : (3 V I/F port) Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
1 : (3 V I/F port) Common use

134 MAD00067DEM
 MN101EF41N

 A/D converter
10-bit × 8 channels (with S/H)

 Special Ports
Buzzer output. High-current drive port

 ROM Correction
Correcting address designation: Up to 7 addresses possible

 Pin Assignment
QFP100-P-1818B

P40, SBO4, TXD4

P41, SBI4, RXD4

P67, KEY7, A15

P66, KEY6, A14
P65, KEY5, A13
P64, KEY4, A12
P76, SD6, NWE
P77, SD7, NDK

P75, SD5, NRE

P74, SD4, NCS
P87, LED7, D7
P86, LED6, D6
P85, LED5, D5
P84, LED4, D4
P83, LED3, D3
P82, LED2, D2
P81, LED1, D1
P80, LED0, D0

P73, SD3, A19

P72, SD2, A18
P71, SD1, A17
P70, SD0, A16
P42, SBT4

VSS
P43
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
CTX, SBO0B, TXD0B, P90 76 50 P63, KEY3, A11
CRX, SBI0B, RXD0B, P91 77 49 P62, KEY2, A10
SBT0B, P92 78 48 P61, KEY1, A9
SBO3B, SDA3B, P93 79 47 P60, KEY0, A8
SBI3B, P94 80 46 P57, A7
SBT3B, SCL3B, P95 81 45 P56, A6
SBO2B, SDA2B, PD0 82 44 P55, A5
SBI2B, PD1 83 43 P54, A4
SBT2B, SCL2B, PD2 84 42 P53, A3
IRQ0B, PD3 85 41 P52, A2
IRQ1B, PD4 86 40 P51, A1
IRQ2B, PD5 87 39 VSS
IRQ3B, PD6 88 38 P50, A0
VDD5 89 37 VDD18
PD7 90 36 P35, SBT3A, SCL3A
VSS 91 35 P34, SBI3A
AN0, PA0 92 34 P33, SBO3A, SDA3A
AN1, PA1 93 33 P32, SBT1
AN2, PA2 94 32 P31, SBI1, RXD1
AN3, PA3 95 31 P30, SBO1, TXD1
AN4, PA4 96 30 P25, IRQ5
AN5, PA5 97 29 P24, IRQ4
AN6, PA6 98 28 P23, IRQ3A
AN7, PA7 99 27 P22, IRQ2A
VREF+ 100 26 P21, IRQ1A
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
SBO0A, TXD0A, P00
SBI0A, RXD0A, P01
SBT0A, P02
SBO2A, SDA2A, P03
SBI2A, P04
SBT2A, SCL2A, P05
BUZZER, P06
TM0IO, P10

TM2IO, P12
MMOD
OSC2
OSC1
VSS
XI
XO
VDD33
VDD18

TM3IO, P13
TM7IOA, P14
TM7OB, P15
TM7OC, P16
SYSCLK, P17
IRQ0A, P20
TM1IO, P11

NRST, P27

Note) Pin 1 to Pin 75: VDD33 = 2.7 V to 3.6 V

Pin 76 to Pin 100: VDD5 = VDD33 to 5.5 V

MAD00067DEM 135
 MN101E49 Series
Type MN101E49K MN101EF49N
Internal ROM type Mask ROM FLASH
ROM (byte) 256K 512K
RAM (byte) 12K 30K
Package (Lead-free) LQFP100-P-1414 (Under development) LQFP100-P-1414
Minimum Instruction 79.4 ns (at 2.7 V to 3.6 V, 12.58 MHz)
Execution Time

 Interrupts
RESET. Watchdog. External 0 to 5. Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer A to E. Time base. Serial 0 (2 systems). Serial 1 (2
systems). Serial 2. Serial 3 (2 systems). Serial 4 (2 systems). Automatic transfer finish (2 systems). A/D conversion finish. Key interrupt.
IEBus*
* IEBus is a trademark of NEC Electronics Corporation.

 Timer Counter
8-bit timer × 10
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Real time output control
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event. Pulse width measurement. Real time
output control. Serial baud rate timer
Timer 3 ..................Square-wave output. Event count. Serial baud rate timer
Timer 6 ..................8-bit freerun timer. Time base timer
Timer A, B, C, D, E
Timer 0, 1 can be cascade-connected
Timer 0, 1, 2 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 0, 1, 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
width measurement. Input capture
Time base timer: One-minute count setting
Watchdog timer × 1

 Serial interface
Synchronous type/UART (full-duplex) × 3: Serial 0, 1, 4
Synchronous type/Single-master I2C × 1: Serial 2
Synchronous type/I2C × 1: Serial 3

 IEBus Interface
Number of channels: 1 channels
Communication mode: Selectable from mode 1 or mode 2
Driver and receiver: External

 DMA controller
Number of channels: 2 channels
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer

 I/O Pins
I/O 22 : (5 V I/F port) Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
62 : (3 V I/F port) Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
1 : (3 V I/F port) Common use

 A/D converter
10-bit × 8 channels (with S/H)

136 MAD00074CEM
 MN101E49K, MN101EF49N

 Special Ports
Buzzer output. High-current drive port

 ROM Correction
Correcting address designation: Up to 7 addresses possible

 Pin Assignment
LQFP100-P-1414

P40, SBO4, TXD4

P41, SBI4, RXD4

P67, KEY7, A15

P66, KEY6, A14
P65, KEY5, A13
P64, KEY4, A12
P76, SD6, NWE
P77, SD7, NDK

P75, SD5, NRE

P74, SD4, NCS
P87, LED7, D7
P86, LED6, D6
P85, LED5, D5
P84, LED4, D4
P83, LED3, D3
P82, LED2, D2
P81, LED1, D1
P80, LED0, D0

P73, SD3, A19

P72, SD2, A18
P71, SD1, A17
P70, SD0, A16
P42, SBT4

VSS
P43
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
SBO0B, TXD0B, P90 76 50 P63, KEY3, A11
SBI0B, RXD0B, P91 77 49 P62, KEY2, A10
SBT0B, P92 78 48 P61, KEY1, A9
SBO3B, SDA3B, P93 79 47 P60, KEY0, A8
IETXA, SBI3B, P94 80 46 P57, A7
IERXA, SBT3B, SCL3B, P95 81 45 P56, A6
SBO2B, SDA2B, PD0 82 44 P55, A5
SBI2B, PD1 83 43 P54, A4
SBT2B, SCL2B, PD2 84 42 P53, A3
IRQ0B, PD3 85 41 P52, A2
IRQ1B, PD4 86 40 P51, A1
IETXB, IRQ2B, PD5 87 39 VSS
IERXB, IRQ3B, PD6 88 38 P50, A0
VDD5 89 37 VDD18
PD7 90 36 P35, SBT3A, SCL3A
VSS 91 35 P34, SBI3A
AN0, PA0 92 34 P33, SBO3A, SDA3A
AN1, PA1 93 33 P32, SBT1
AN2, PA2 94 32 P31, SBI1, RXD1
AN3, PA3 95 31 P30, SBO1, TXD1
AN4, PA4 96 30 P25, IRQ5
AN5, PA5 97 29 P24, IRQ4
AN6, PA6 98 28 P23, IRQ3A
AN7, PA7 99 27 P22, IRQ2A
VREF+ 100 26 P21, IRQ1A
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
SBO0A, TXD0A, P00
SBI0A, RXD0A, P01
SBT0A, P02
SBO2A, SDA2A, P03
SBI2A, P04
SBT2A, SCL2A, P05
BUZZER, P06
TM0IO, P10

TM2IO, P12
MMOD
OSC2
OSC1
VSS
XI
XO
VDD33
VDD18

TM3IO, P13
TM7IOA, P14
TM7OB, P15
TM7OC, P16
SYSCLK, P17
IRQ0A, P20
TM1IO, P11

NRST, P27

Note) Pin 1 to Pin 75: VDD33 = 2.7 V to 3.6 V

Pin 76 to Pin 100: VDD5 = VDD33 to 5.5 V

MAD00074CEM 137
 MN101E63 Series
Type MN101EF63G
Internal ROM type FLASH
ROM (byte) 128K
RAM (byte) 10K
Package (Lead-free) TQFP064-P-1010C (Under development)
50 ns (at 2.7 V to 5.5 V, 20 MHz)
Minimum Instruction 125 ns (at 1.8 V to 5.5 V, 8 MHz)
Execution Time *: at internal 2 , 3 , 4 , 5 , 6 , 8 , 10 times oscillation used

 Interrupts
5 external interrupts. 29 internal interrupts
RESET. NMI. External 0 to 4. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems). Timer 9 (3 systems). Time base. 24H
timer. Alarm. Serial 0 (2 systems). Serial 1 (2 systems). Serial 2 (2 systems). Serial 4 (2 systems). CAN. LIN. A/D conversion. ATC. Key
interrupt. Low voltage detection

 Timer Counter
8-bit timer × 7
Timer 0 ..................Timer pulse output. Added pulse(2-bit)type PWM output to large current terminal TM0IOB possible. Event count.
Simple pulse width measurement
Timer 1 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 0, 1). Timer synchronous output
Timer 2 ..................Timer pulse output. Added pulse(2-bit)type PWM output to large current terminal TM2IOB possible. Event count.
Simple pulse width measurement. 24-bit cascade connected (timer 0, 1, 2). Timer synchronous output
Timer 3 ..................Timer pulse output. Event count. 16-bit cascade connected (timer 2, 3). 32-bit cascade connected (timer 0, 1, 2, 3)
Timer 4 ..................Timer pulse output. Added pulse (2-bit) type PWM output. Event count. Simple pulse width measurement
Timer 6 ..................8-bit freerun timer
Timer A..................Baud rate timer. Clock output for peripheral function
16-bit timer × 3
Timer 7 ..................Timer pulse output to large current terminal TM7IOB possible. Event count. High accuracy PWM/IGBT output
(cycle/duty continuous variable). Pulse width measurement. Timer synchronous output. Input capture (both edge
available). Real time output control. Double buffer compare register
Timer 8 ..................Timer pulse output to large current terminal TM8IOB possible. Event count. High accuracy PWM output
(cycle/duty continuous variable). Pulse width measurement. Input capture (both edge available). 32-bit cascade
connected (timer 7, 8). 32-bit PWM output. Synchronous output event. Double buffer compare register
Timer 9 ..................Timer pulse output to large current terminal TM9IOB possible. 3-phase PWM output. Triangular waveform
output. Jigsaw waveform output. Dead time setup. Event count
24H timer: Interval function (Interruption every 0.5 seconds, every 1 second, every 1 minute, every 1 hour and 24 hours). Alarm function
Time base timer: One-minute count setting
Watchdog timer × 2

 Serial interface
Synchronous type/UART (full-duplex)/LIN × 1: Serial 0
Synchronous type/UART (full-duplex) × 2: Serial 1, 2
Synchronous type/Multi-master I2C × 1: Serial 4

 CAN controller
Number of channels: 1 channels
CAN Protocol Specification Version: CAN2.0B
Transmission speed: Max. 1 Mbps
Data length code: 0 byte to 8 bytes
Message frame types: Standard and extended frame format supported
Standard (SFF) ID: 11-bit. Extended (EFF) ID: 29-bit
Buffer size (each channel): 32 (transmission/reception)

 DMA controller
1 systems. Maximum transfer cycles are 255
Starting factor: External request. Internal event. Software

 I/O Pins
I/O 54 : Common use. Specified pull-up/pull-down resistor available. Input/output selectable (bit unit)

138 MAD00082AEM
 MN101EF63G

 A/D converter
10-bit × 12 channels

 Display control function

LCD: 32 segments × 4 commons (Static, 1/2, 1/3, or 1/4 duty)
Usable if VLC1 ≤ VDD

 Special Ports
High-current drive port

 Reset
Low voltage detection. Automatic Reset. Reset factor detection

 Internal oscillation
High speed: 20 MHz/16 MHz. Low speed: 30 kHz

 Pin Assignment
TQFP064-P-1010C
P71, SEG7, KEY1, SBO4A, SDA4A

P75, SEG3, KEY5, SBO1B, TXD1B

P76, SEG2, KEY6, SBI1B, RXD1B
P72, SEG6, KEY2, SBT4, SCL4A
P65, SEG11, SBO2A, TXD2A

P81, COM0, SDO1, TM9OD1

P82, COM1, SDO2, TM9OD2
P83, COM2, SDO3, TM9OD3
P84, COM3, SDO4, TM9OD4
P66, SEG10, SBI2A, RXD2A

P80, SEG0, SDO0, TM9OD0

P77, SEG1, KEY7, SBT1B
P70, SEG8, KEY0, SBI4A
P67, SEG9, SBT2A

P73, SEG5, KEY3

P74, SEG4, KEY4
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33

TM4IOB, SEG12, P64 49 32 TM9OD5, SDO5, VLC3, P85

TM3IOB, SEG13, P63 50 31 P86, VLC2, SDO6, CRXB
TM1IOB, SEG14, P62 51 30 P87, VLC1, SDO7, CTXB
TXD1A, SBO1A, SEG15, P50 52 29 P24, IRQ4
RXD1A, SBI1A, SEG16, P51 53 28 P23, IRQ3
SBT1A, SEG17, P52 54 27 P22, IRQ2
CTXA, SEG18, P53 55 26 P21, IRQ1
CRXA, SEG19, P54 56 25 P20, IRQ0
AN11, SEG20, P55 57 24 P05, LED5
AN10, SEG21, P56 58 23 P04, LED4, TM0IOB, TM2IOB, SBT0A
AN9, SEG22, P57 59 22 P03, LED3, TM8IOB, SBO0A, TXD0A
AN8, SEG23, P94 60 21 P02, LED2, TM7IOB, SBI0A, RXD0A
TM0IOA, AN0, SEG24, PA0 61 20 P01, LED1, TM9IOB, OCD_CLK
TM1IOA, AN1, SEG25, PA1 62 19 P00, LED0, OCD_DATA
TM2IOA, AN2, SEG26, PA2 63 18 VSS
TM3IOA, AN3, SEG27, PA3 64 17 RON
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9

VDD5
VREF+

XI, P90
XO, P91
VSS
OSC1, P25
OSC2, P26

MMOD
VDD18
DMOD
NRST, P27
TM4IOA, AN4, SEG28, PA4
TM7IOA, AN5, SEG29, PA5
TM8IOA, AN6, SEG30, PA6
TM9IOA, AN7, SEG31, PA7

ATRST

MAD00082AEM 139
140
 AM2 (MN102) Series

The AM2(MN102) Series of 16-bit single-chip microcomputers offers

high-speed operation with a minimum instruction
execution time of only 50 ns (at 40 MHz).
The C compiler generates ROM code that is only 20% larger than
assembler code.
The Series continues to add new versions tailored for specifi c types of
applications so as to bring the benefi ts
of compactness and high performance to a wider range of applications.

Features
• 16-bit architecture
1-bit minimum instruction code -- 50 ns minimum instruction
execution time (at 40 MHz)
• Elegant architecture
High-Efficiency 1 byte per cycle instructions
Achievement of higher speeds for load/store transfer and branch
instructions, etc.
• Flexible expansion of functions
Achievement of a microcontroller that supports customization
through an ASIC expansion bus
• Software support
ANSI C language -- µITRON*-specification realtime OS
*: ITRON is an abbreviation of "Industrial TRON."

 Application
 MN102H46 Series
Type MN102H460B
Internal ROM type External
ROM (byte) 
RAM (byte) 4K
Package (Lead-free) LQFP128-P-1818C, TQFP128-P-1414B
[With main clock operated]
Minimum Instruction 50 ns (at 3.0 V to 3.6 V, 40 MHz)
Execution Time 100 ns (at 2.0 V to 3.6 V, 20 MHz)

 Interrupts
/RST pin, Watchdog, /NMI pin, Timer counter 4 to15, Timer counter 16, Timer counter 17, Timer counter 21, Timer counter 16 to 20
compare capture A, Timer counter 16 to 20 compare capture B, Timer counter 21 capture A, Timer counter 21 capture B, Timer counter
21 capture D, Timer counter 21 compare E, Timer counter 21 compare F, ATC ch.0 to ch.3 transfer finish, External 0 to 7, Serial ch.0 to
ch.3 transmission, Serial ch.0 to ch.3 reception, /KI pin (OR), A/D conversion finish

 Timer Counter
8-bit timer × 16
Timer 0, 1 ..............prescalers
Timer 2, 3 ..............UART baud rate generator
Timer 4 ..................timer output, A/D conversion start up
Timer 5, 9 ..............UART baud rate generator
Timer 6 to 8 ...........timer output
Timer 10 to 15 .......timer output
[Connectable] timer counter 0 to 3, 4 to 7, 8 to 11, 12 to 15
16-bit timer × 5
Timer 16 to 20 .......timer output, event count, input capture, output compare, PWM output, 2-phase encorder inpu
24-bit timer × 1
Timer 21 ................servo control

 Serial interface
Serial 0, 1 : 8-bit × 1 (transfer direction of MSB / LSB selectable, transmission / reception of 7, 8-bit length)

Serial 2, 3 : 8-bit × 1 (transfer direction of MSB / LSB selectable, transmission / reception of 7, 8-bit length)
UART × 4 (common use with serial 0 to 3)
I2C × 2 (common use with serial 1, 3; single master)

 I/O Pins
I/O 55 : Common use : 55 (use of full address, address data separate 16-bit mode)
Common use : 72 (use of address 16-bit, address data multiplex 16-bit mode)
Input 8 : Common use : 8

 A/D converter
10-bit × 12-ch. (maximum input is 16) (with S/H)

 PWM
16-bit × 5-ch. (timer counter 16 to 20)

 ICR
16-bit × 5-ch., 24-bit × 1-ch. (timer counter 16 to 21)

 OCR
16-bit × 5-ch., 24-bit × 1-ch. (timer counter 16 to 21)

 Notes
Address / data multiplex bus interface, address / data separate bus interface,
8-bit / 16-bit bus width selectable

142 MAE00007GEM
 MN102H460B

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
VI = VDD or VSS, output open
Operating supply current IDDopr 50 mA
f = 40 MHz , VDD = 3.3 V
Supply current at STOP IDDS Pin with pull-up resistor is open all other input pins and Hi-Z 50 µA
state input/output pins are simultaneously applied VDD or
VSS level
Supply current at HALT IDDH f = 40 MHz , VDD = 3.3 V, output open 25 mA
(Ta = –20°C to +70°C , VDD = AVDD = 3.3 V , VSS = AVSS = 0 V)

 Pin Assignment
LQFP128-P-1818C, TQFP128-P-1414B
P96, AN14, TM15O, TM19IB
P95, AN13, TM13O, TM2I
P94, AN12, TM11O, TM4I
P97, AN15, TM20IB

PB4, SBO3, SDA3

PB5, SBT3, SCL3
PC7, NBRACK
P51, WEH, WE

PC6, NBREQ

PD5, RTP5
PD4, RTP4
P92, AN10
P93, AN11

PB3, SBI3
P50, WEL

P91, AN9
P90, AN8

P87, AN7
P86, AN6
P85, AN5
P84, AN4
P83, AN3
P82, AN2
P81, AN1
P80, AN0
P52, RE

VREFH

VREFL
AVDD

AVSS

VDD
VSS
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
P53, CS2, ALE 97 64 PB2, SBT2, TM18IC
VDD 98 63 PB1, SBO2, TM17IC
VSS 99 62 PB0, SBI2, TM16IC
P54, RAS, RFSH 100 61 PA5, SBT1, SCL1
P55, CAS, LCAS, BIBT1 101 60 PA4, SBO1, SDA1
P56, CS3, UCAS, BIBT2 102 59 PA3, SBI1
P20, A0, KI0 103 58 PA2, SBT0
P21, A1, KI1 104 57 PA1, SBO0
P22, A2, KI2 105 56 PA0, SBI0
P23, A3, KI3 106 55 P75, TM18IOB, TM21ID
P24, A4, KI4 107 54 P74, TM18OA
P25, A5, KI5 108 53 P73, TM17OB, STOP
P26, A6, KI6 109 52 P72, TM17OA
P27, A7, KI7, TMI17B 110 51 P77, TM20IOA
P30, A8 111 50 VDD
PD6, RTP6 112 49 PD3, RTP3
PD7, RTP7 113 48 PD2, RTP2
P31, A9 114 47 P71, TM16OB, WDOUT
P32, A10 115 46 P70, TM16OA
P33, A11 116 45 P67, IRQ7, EXTDK
P34, A12 117 44 P66, IRQ6
P35, A13 118 43 P65, IRQ5, TM18IA
VDD (VPP) 119 42 P64, IRQ4, TM17IA
PC4, TM12O, TM8I, TM21IA 120 41 P63, IRQ3, TM16IB
P36, A14 121 40 P62, IRQ2, TM16IA
P37, A15 122 39 P61, IRQ1, TM3I
P40, A16 123 38 P60, IRQ0
P41, A17 124 37 P76, TM19IOA
P42, A18 125 36 PC0, TM4O, TM10I
P43, A19 126 35 RST
P44, A20 127 34 PC5, NMI
P45, A21 128 33 P57, /DUMX, BOSC
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
11
1
2
3
4
5
6
7
8
9
P46, A22, CS0
P47, A23, CS1
P00, AD0, D0
P01, AD1, D1
P02, AD2, D2
P03, AD3, D3
VDD
VSS
P04, AD4, D4
P05, AD5, D5
P06, AD6, D6
P07, AD7, D7
P10, AD8, D8

P12, AD10, D10

P14, AD12, D12

P15, AD13, D13
P16, AD14, D14
P17, AD15, D15
MODE0
MODE1
MODE2
PC3, TM10O, TM7I, TM21IR
PC2, TM8O, TM6I

VDD
OSCI
OSCO
VSS
P11, AD9, D9

PC1, TM6O, TM11I

PD0, RTP0
PD1, RTP1
P13, AD11, D11

MAE00007GEM 143
 MN102H60 Series
Type MN102H60G MN102H60K MN102HF60G MN102HF60K
Internal ROM type Mask ROM FLASH
ROM (byte) 128K 256K 128K 256K
RAM (byte) 4K 10K 4K 10K
LQFP100-P-1414, LQFP100-P-1414,
Package (Lead-free) LQFP100-P-1414 LQFP100-P-1414
MLGA100-L-1010 MLGA100-L-1010
Minimum Instruction [With main clock operated] 58 ns (at 3.0 V to 3.6 V, 34 MHz)
Execution Time

 Interrupts
/RST pin, Watchdog, /NMI pin, Timer counter 0 to 7 underflow, Timer counter 8 to 12 underflow, Timer counter 8 to 12 compare capture A,
Timer counter 8 to 12 compare capture B, ATC ch.0 to ch.3 transfer finish, ETC ch.0 to ch.1 transfer finish, External 0 to 4, Serial ch.0 to
ch.4 transmission, Serial ch.0 to ch.4 reception, /KI pin (OR), A/D conversion finish

 Timer Counter
8-bit timer × 10
Timer 0 ..................prescaler, timer output, event count, clock supply for 16-bit timer, timer interrupts
Timer 1, 2 ..............serial clock generator, timer interrupts
Timer 3 ..................A/D conversion start up, timer interrupts
Timer 4 ..................prescaler, serial clock generator, timer output, event count, clock supply for 16-bit timer, timer interrupts
Timer 5 ..................serial clock generator, timer interrupts
Timer 6 ..................timer interrupts
Timer 7 ..................timer output, event count, timer interrupts
Timer 13, 14 ..........simple PWM output
[Connectable] timer counter 0 to 7
[Connectable] timer counter 13, 14
16-bit timer × 6
Timer 8 to 12 .........timer output, event count, input capture, PWM output, 2-phase encoder input
Timer 15 ................pulse width measurement

 Serial interface
Serial 0, 1 : 8-bit × 1 (transfer direction of MSB / LSB selectable, transmission / reception of 7, 8-bit length)

Serial 2, 3 : 8-bit × 1 (transfer direction of MSB / LSB selectable, transmission / reception of 7, 8-bit length)

Serial 4 : 8-bit × 1 (transfer direction of MSB / LSB selectable, transmission / reception of 7, 8-bit length)
UART × 2 (common use with serial 3, 4)
I2C × 2 (common use with serial 3,4; single master)

 I/O Pins
I/O 82 : Common use : 46 (address data separate 8-bit mode)
Common use : 53 (address data multiplex 8-bit mode)

 A/D converter
10-bit × 8-ch. (with S/H)

 PWM
16-bit × 5-ch. (timer counter 8 to 12)

 ICR
16-bit × 5-ch. (timer counter 8 to 12)

 OCR
16-bit × 5-ch. (timer counter 8 to 12)

 Notes
Address / data multiplex bus interface, address / data separate bus interface,
8-bit / 16-bit bus width selectable

144 MAE00005MEM
 MN102H60G, MN102H60K, MN102HF60G, MN102HF60K

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
VI = VDD or VSS, output open
Operating supply current IDDopr 60+10α* mA
f = 34 MHz , VDD = 3.3 V
Supply current at STOP IDDS Pin with pull-up resistor is open All other input pins and Hi-Z 70 µA
state input/output pins are simultaneously applied VDD or
VSS level
Supply current at HALT IDDH f = 34 MHz , VDD = 3.3 V, output open 30+10α* mA
(Ta = –40°C to +85°C , VDD = AVDD = 3.3 V , VSS = AVSS = 0 V)
Note) * "α" depends on products. MN102H60G, MN102H60K α= 0; MN102HF60G α= 1; MN102HF60K α= 2

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Non-linear error 10-bit ±4 LSB
A/D conversion time at 34 MHz 3.29 µs
Analog input voltage VIA VSS VDD V
(Ta = 25°C , VDD = AVDD = 3.3 V , VSS = AVSS = 0 V)

 Pin Assignment
LQFP100-P-1414 P91, TM10IOA, BIBT2, /DMAACK1
P90, TM8IOA, BIBT1, /DMAREQ1

P85, TM9IOA, SBT4, SCL4, SBO2

P92, TM10IOB, /DMAREQ0
P93, TM10IC, /DMAACK0

P84, TM7IO, SBO3, SDA3

P87, TM9IC, SBO4, SDA4
P71, SBI0, /LCAS, /CAS

P86, TM9IOB, SBI4

P73, SBT1, DMUX
P72, SBO0, /UCAS

P83, TM4IO, SBI3

P70, SBT0, /RAS
P75, SBO1
P74, SBI1

P97, AN3
P96, AN2
P95, AN1
P94, AN0

VREF+
AVSS
/NMI

VDD
*
*
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51

PA0, /IRQ0 76 50 P82, TM0IO, SBT3, SCL3, SBI2

PA1, /IRQ1 77 49 P81, TM140B
PA2, /IRQ2 78 48 P80, TM140A
PA3, /IRQ3 79 47 A23, P47, AN7, WDOUT
PA4, /IRQ4, TM15IB 80 46 A22, P46, AN6, STOP
(ADSEP) 81 45 A21, P45, AN5
/RST 82 44 A20, P44, AN4
VDD 83 43 VREF-
D0 84 42 A19, P43
D1 85 41 A18, P42
D2 86 40 A17, P41
D3 87 39 A16, P40
D4 88 38 A15, P37, /KI7
D5 89 37 A14, P36, /KI6
D6 90 36 A13, P35, /KI5
D7 91 35 A12, P34, /KI4
VSS 92 34 AVDD
D8 93 33 A11, P33, /KI3
D9 94 32 A10, P32, /KI2
D10 95 31 A9, P31, /KI1
D11 96 30 A8, P30, /KI0
D12 97 29 A7, P27
D13 98 28 A6, P26
D14 99 27 A5, P25
D15 100 26 A4, P24, TM15IA
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
/RE, P61
/WEL, P62
/WE, /WEH, P63
P50, /CS0, TM13OA
P51, /CS1, TM13OB
P52, /CS2, TM14OA
P53, /CS3, TM14OB
P54, /BREQ
P55, /BRACK
P56, /BSTRE, TM15IA
(/WORD)
A0, P20, SBT2
A1, P21, SBI2
A2, P22, SBO2
A3, P23
VDD
BOSC, PB0, BIBT1, BIBT2
VSS
XI, PB1
XO
VDD
OSCI
OSCO
(MODE)
P60, WAIT, SBT2

Note) 1. Pin position in 16-bit bus width address data split memory extension mode.
2. *: Use 33 k Ω to 50 k Ω

MAE00005MEM 145
 MN102L59 Series
Type MN102L59D MN102LF59D
Internal ROM type Mask ROM FLASH
ROM (byte) 64K
RAM (byte) 2K
Package (Lead-free) LQFP064-P-1414
Minimum Instruction [With main clock operated] 100 ns (at 4.5 V to 5.5 V, 5 MHz externally, multiplied by 4 internally)
Execution Time

 Interrupts
RESET, Watchdog, Timer counter 0 to 11, External 0 to 5, Serial ch.0 transfer finish, Serial ch.1 transfer finish, /NMI pin, A/D conversion
finish

 Timer Counter
8-bit timer × 9
Timer 0 ..................timer output, event count
Timer 1 ..................timer output, event count, A/D conversion start up
Timer 2 ..................timer output, event count
Timer 3 ..................interval timer, UART baud rate generator
Timer 4, 5 ..............interval timer
Timer 8, 9 ..............timer output, event count, simple PWM output
Timer 10 ................timer output, simple inverter control [simple 6-phase PWM output]
[Connectable] timer counter 0, 1, 2 timer counter 0, 4, 5
16-bit timer × 3
Timer 6, 7 ..............timer output, event count
Timer 11 ................16-bit updown counter : highly functional inverter control [simple 6-phase PWM output], A/D conversion start

 Serial interface
Serial 0, 1 : 1 to 8-bit × 1 (common use with half-duplex UART, transfer direction of MSB/LSB selectable)
Half-duplex UART × 2 (common use with serial 0, 1)

 I/O Pins
I/O 52 : Common use : 52 (by bit)

 A/D converter
10-bit × 12-ch. (with S/H) : 4 channels for common use

 PWM
16-bit × 2-ch. (commen use with timer counter 6,7)
simple 6-phase PWM output 8-bit × 1-ch.(common use with timer counter 10)
6-phase PWM output 16-bit × 1ch. (timer counter 11)

 Notes
6-phase PWM output support

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
VI = VDD or VSS, output open
Operating supply current IDDopr 75 mA
f = 5 MHz , VDD = 5.0 V
Supply current at STOP IDDS Pin with pull-up resistor is open all other input pins and Hi-Z 50 µA
state input/output pins are simultaneously applied VDD or
VSS level
Supply current at HALT IDDH f = 5 MHz , VDD = 5.0 V, output open 30 mA
(Ta = –20°C to +85°C, VDD = 5.0V, VSS = 0V)

146 MAE00001JEM
 MN102L59D, MN102LF59D

 Pin Assignment
LQFP064-P-1414

P16, TMIO6
P15, TMIO5
P14, TMIO4
P13, TMIO3
P12, TMIO2

P10, TMIO0
P11, TMIO1
P25, /IRQ5
P24, /IRQ4
P23, /IRQ3
P22, /IRQ2
P21, /IRQ1
P20, /IRQ0

P02, SBO0

P00, SBT0
P01, SBI0
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
P40, PWM0, TMIO0 49 32 P37, AN0
P41, /PWM0, TMIO1 50 31 P36, AN1
P42, PWM1, TMIO2 51 30 P35, AN2
P43, /PWM1, TMIO6 52 29 P34, AN3
P44, PWM2, TMIO7 53 28 P33, AN4
P45, /PWM2, STOP 54 27 P32, AN5
P60, TPWM0, SBT0 55 26 P31, AN6
P61, TPWM1, SBI0 56 25 P30, AN7
P62, TPWM2, SBO0 57 24 P57, AN8
P63, TPWM3, SBT1 58 23 P56, AN9
P64, TPWM4, SBI1 59 22 P55, AN10
P65, TPWM5, SBO1 60 21 P54, AN11
VDD 61 20 P53
62 19 P52
63 18 P51
/NMI 64 10 17 P50

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9
P70, BUZZ
P71
P72
P73
P74
P75
P76
P77, WDOUT
VSS
/RST
VSS
SYSCLK
VDD
OSCI
OSCO
VDD

Note) The MN102LF59D is manufactured and sold under license agreement with BULL CP8 Inc.
Note that MN102LF59D cannot be used as the IC card.

MAE00001JEM 147
 MN102H73 Series
Type MN102H730FGT MN102H73G MN102H73K MN102HF73G MN102HF73K
Internal ROM type External Mask ROM FLASH
ROM (byte)  128K 256K 128K 256K
RAM (byte) 10K 12K 10K 12K
Package (Lead-free) TQFP128-P-1414B TQFP128-P-1414A TQFP128-P-1414B
Minimum Instruction [With main clock operated] 58 ns (at 3.0 V to 3.6 V, 34 MHz)
Execution Time

 Interrupts
/RST pin, Watchdog, /NMI pin, Timer counter 0 to 9 underflow, Timer counter 10 to 14 underflow, Timer counter 10 to 14 compare
capture A, Timer counter 10 to 14 compare capture B, ATC ch.0 to ch.1 transfer finish, ETC ch.0 to ch.1 transfer finish, External 0 to 7,
Serial ch.0 to ch.3 transmission, Serial ch.0 to ch.3 reception, A/D conversion finish

 Timer Counter
8-bit timer × 10
16-bit timer × 5
Timer 10 to 14 .......timer output, event count, input capture, PWM output, 2-phase encoder input

 Serial interface
Serial 0, 1 : 8-bit × 1 (transfer direction of MSB / LSB selectable, transmission / reception of 7, 8-bit length)
Serial 2, 3 : 8-bit × 1 (transfer direction of MSB / LSB selectable, transmission / reception of 7, 8-bit length)
UART × 4 (common use with serial 0 to 3)
I2C × 2 (common use with serial 1,3; single master)

 Multiply-and-Accumulate
16-bit sign × 16-bit sign + 40-bit sign

 I/O Pins
I/O 105 : Common use : 59 (use of full address, address data separate 16-bit mode)
Common use : 76 (use of address 16-bit, address data separate 8-bit mode)

 A/D converter
10-bit × 12-ch. (with S/H)

 D/A converter
8-bit × 4-ch.

 PWM
16-bit × 5-ch. (timer counter 10 to 14)

 ICR
16-bit × 5-ch. (timer counter 10 to 14)

 OCR
16-bit × 5-ch. (timer counter 10 to 14)

 Notes
Address / data separate bus interface; 8 / 16-bit bus width selectable; SRAM interface

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
VI = VDD or VSS, output open
Operating supply current IDDopr 60+10α* mA
f = 34 MHz , VDD = 3.3 V
Supply current at STOP IDDS Pin with pull-up resistor is open all other input pins and Hi-Z 70 µA
state input/output pins are simultaneously applied VDD or
VSS level
Supply current at HALT IDDH f = 34 MHz , VDD = 3.3 V, output open 30+10α* mA
(Ta = –40°C to +85°C , VDD = AVDD = 3.3 V , VSS = AVSS = 0 V)
Note)* "α" depends on products .
MN102H73G/73K/730F α = 0
MN102HF73G α = 1
MN102HF73K α = 2
148 MAE00010KEM
 MN102H730FGT, MN102H73G, MN102H73K, MN102HF73G, MN102HF73K

 Pin Assignment
TQFP128-P-1414A, TQFP128-P-1414B

PC7, /BRACK

PD5, TM5IO
PD4, TM4IO
PC6, /BREQ
P97, DAC3
P96, DAC2
P95, DAC1
P94, DAC0

SBO3, PB4
/WEH, P51

SBT3, PB5
/WEL, P50

P92, AN10
P91, AN09
P90, AN08

P87, AN07
P86, AN06
P85, AN05
P84, AN04
P83, AN03
P82, AN02
P81, AN01
P80, AN00
P93, AN11

SBI3, PB3
/RE, P52

VREFH

VREFL
AVDD

AVSS

VDD
VSS
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
/CS2, P53 97 64 PB2, SBT2, TM12IC
VDD 98 63 PB1, SBO2, TM11IC
VSS 99 62 PB0, SBI2, TM10IC
/BSTRE, P54 100 61 PA5, SBT1 *
/WR, P55 101 60 PA4, SBO1 *
/CS3, P56 102 59 PA3, SBI1
A00, P20 103 58 PA2, SBT0
A01, P21 104 57 PA1, SBO0
A02, P22 105 56 PA0, SBI0
A03, P23 106 55 P75, TM12IOB
A04, P24 107 54 P74, TM14IC
A05, P25 108 53 P73, TM11IOB, STOP
A06, P26 109 52 P72, TM14IOB
A07, P27 110 51 P77, TM14IOA
A08, P30 111 50 VDD
TM6IO, PD6 112 49 PD3, TM3IO, /DMAREQ0
TM7IO, PD7 113 48 PD2, TM2IO, /DMAACK0
A09, P31 114 47 P71, TM13IC, WDOUT
A10, P32 115 46 P70, TM13IOB
A11, P33 116 45 WAIT, P67, IRQ7
A12, P34 117 44 P66, IRQ6
A13, P35 118 43 P65, TM12IOA, IRQ5
VDD 119 42 P64, TM11IOA, IRQ4
TM8IO, PC4 120 41 P63, TM10IOB, IRQ3
A14, P36 121 40 P62, TM10IOA, IRQ2
A15, P37 122 39 P61, TM3IO, IRQ1
A16, P40 123 38 P60, IRQ0
A17, P41 124 37 P76, TM13IOA
A18, P42 125 36 PC0, TM9IO
A19, P43 126 35 /RST
A20, P44 127 34 /NMI
A21, P45 128 33 BOSC
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
11
1
2
3
4
5
6
7
8
9

MODE
/CS0, P46
/CS1, P47
D00, P00
D01, P01
D02, P02
D03, P03
VDD
VSS
D04, P04
D05, P05
D06, P06
D07, P07
P10, D08

P12, D10
/DMAACK1, PD0, TM0IO
/DMAREQ1, PD1, TM1IO

P14, D12
P15, D13
P16, D14
P17, D15
PC1, /WORD
VDD

PC3, TM2IO
XI
XO
VDD
OSCI
OSCO
VSS
P11, D09

P13, D11

Note) *: Use 4.7 kW to 10 kW

MAE00010KEM 149
 MN102H95 Series
Type MN102H950F
Internal ROM type External
ROM (byte) 
RAM (byte) 10K
Package (Lead-free) LQFP100-P-1414
Minimum Instruction [With main clock operated] 58 ns (at 3.0 V to 3.6 V, 34 MHz)
Execution Time

 Interrupts
/RST pin, Watchdog, /NMI pin, Timer counter 0 to 9 underflow, Timer counter 10 to 14 underflow, Timer counter 10 to 14 compare
capture A, Timer counter 10 to 14 compare capture B, ATC ch.0 to ch.3 transfer finish, External 0 to 4, Serial ch.0 to ch.4 transmission,
Serial ch.0 to ch.4 reception, A/D conversion finish

 Timer Counter
8-bit timer × 10
16-bit timer × 5
Timer 10 to 14 .......timer output, event count, input capture, PWM output, 2-phase encoder input

 Serial interface
Serial 0, 1 : 8-bit × 1 (transfer direction of MSB / LSB selectable, transmission / reception of 7, 8-bit length)
Serial 2, 3 : 8-bit × 1 (transfer direction of MSB / LSB selectable, transmission / reception of 7, 8-bit length)
UART × 4 (common use with serial 0 to 3)
I2C × 2 (common use with serial 1,3; single master)

 I/O Pins
I/O 63 : Common use : 43 (use of full address, address data separate 16-bit mode)
Common use : 57 (use of address 16-bit, address data separate 8-bit mode)
Common use : 56 (use of full address, address data multiplex 16-bit mode)
Common use : 63 (use of address 16-bit, address data multiplex 8-bit mode)

 A/D converter
10-bit × 12-ch. (with S/H)

 D/A converter
8-bit × 4-ch.

 PWM
16-bit × 5-ch. (timer counter 10 to 14)

 ICR
16-bit × 5-ch. (timer counter 10 to 14)

 OCR
16-bit × 5-ch. (timer counter 10 to 14)

 Notes
Address / data separate bus interface; 8 / 16-bit bus width selectable; SRAM interface
Address / data multiplex bus interface support

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
VI = VDD or VSS, output open
Operating supply current IDDopr 60 mA
f = 34 MHz , VDD = 3.3 V
Supply current at STOP IDDS Pin with pull-up resistor is open all other input pins and Hi-Z 70 µA
state input/output pins are simultaneously applied VDD or
VSS level
Supply current at HALT IDDH f = 34 MHz , VDD = 3.3 V, output open 30 mA
(Ta = –40°C to +85°C , VDD = AVDD = 3.3 V , VSS = AVSS = 0 V)

150 MAE00021EEM
 MN102H950F

 Pin Assignment
LQFP100-P-1414

P17, D15
P16, D14
P15, D13
P14, D12

P12, D10
P13, D11
A6, AD6
A5, AD5
A4, AD4
A3, AD3
A2, AD2
A1, AD1
A0, AD0

P10, D8

P07, D7
P06, D6
P05, D5
P04, D4
P03, D3
P02, D2
P01, D1
P00, D0
P11, D9
VDD

VSS
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
AD7, A7 76 50 MODE
AD8, A8 77 49 OSCO
AD9, A9 78 48 OSCI
AD10, A10 79 47 VDD
AD11, A11 80 46 XO
VSS 81 45 PB2, XI
AD12, A12 82 44 VSS
AD13, A13 83 43 PB1, /NMI
AD14, A14 84 42 VDD
AD15, A15 85 41 /RST
TM0O, A16, P40 86 40 PB0, BOSC
TM2O, A17, P41 87 39 PA5, ADSEP
TM3O, A18, P42 88 38 PA4, /IRQ4, TM14IC
TM4O, A19, P43 89 37 PA3, /IRQ3, TM13IC
VDD 90 36 PA2, /IRQ2, TM12IC
AN0, A20, P44 91 35 PA1, /IRQ1, TM11IC
AN1, A21, P45 92 34 PA0, /IRQ0, TM10IC
STOP, AN2, A22, P46 93 33 P77, TM9IO
WDOUT, AN3, A23, P47 94 32 P76, TM8IO
/CS0 95 31 P75, SBO1, SDA1, TM7IO
/CS1, P51 96 30 P74, SBI1, TM6IO
/CS2, P52 97 29 P73, SBT1, SCL1, TM4IO
/CS3, P53 98 28 P72, SBO0, TM3IO
TM14IOA, /DMAREQ0, /BREQ, /WR, P54 99 27 P71, SBI0, TM2IO
TM14IOB, /DMAACK0, /BRACK, P55 100 26 P70, SBT0, TM0IO
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
ALE, P56
/WORD, P57

/RE
/WEL, P62
/WEH, P63
VDD
TM10IOA, /DMAREQ1, P80
TM10IOB, /DMAACK1, P81

TM12IOA, SBO2, P84

TM12IOB, SBT3, SCL3, P85
TM13IOA, SBI3, P86
TM13IOB, SBO3, SDA3, P87

DAC0, AN4, P90

DAC1, AN5, P91
DAC2, AN6, P92
DAC3, AN7, P93
AN8, P94
AN9, P95
AN10, P96
TM11IOA, SBT2, P82
TM11IOB, SBI2, P83

AN11, P97
AVDD

AVSS
WAIT, P60

MAE00021EEM 151
 MN102H74 Series
Type MN102H74D MN102H74G MN102HF74G
Internal ROM type Mask ROM FLASH
ROM (byte) 64K 128K
RAM (byte) 4K
Package (Lead-free) LQFP100-P-1414
Minimum Instruction [With main clock operated] 83.3 ns (at 3.0 V to 3.6 V, 12 MHz)
Execution Time

 Interrupts
/RST pin, Watchdog, /NMI pin, Timer counter 0 to 9 underflow, Timer counter 10 to 13 under/overflow, Timer counter 10 to 13 compare
capture A, Timer counter 10 to 13 compare capture B, ATC ch.0 to ch.3 transfer finish, External 0 to 5, Serial ch.0 to ch.3 transmission,
Serial ch.0 to ch.3 reception, A/D conversion finish, USB general-purpose, USBSOF, USB end points 1 to 8

 Timer Counter
8-bit timer × 10
Timer 0, 1 ..............timer output, event count, timer interrupt
Timer 2 ..................timer output, event count, timer interrupt, A/D conversion start
Timer 3 to 5 ...........timer output, event count, timer interrupt
Timer 6 to 8 ...........timer output, event count, timer interrupt, serial clock generation
Timer 9 ..................timer output, event count, timer interrupt
[Connectable] Timer 0, 1
[Connectable] Timer 2 to 5
[Connectable] Timer 6 to 9
16-bit timer × 4
Timer 10 to 13 .......timer output, event count, input capture, PWM output, 2-phase encoder input

 Serial interface
Serial 0 : 8-bit × 1 (transfer direction of MSB/LSB selectable; transmission / reception of 7, 8-bit length)
Serial 1 : 8-bit × 1 (transfer direction of MSB/LSB selectable; transmission / reception of 7, 8-bit length)
Serial 2 : 8-bit × 1 (transfer direction of MSB/LSB selectable; transmission / reception of 7, 8-bit length)
Serial 3 : 8-bit × 1 (transfer direction of MSB/LSB selectable; transmission / reception of 7, 8-bit length)
UART × 4 (common use with serial 0 to 3)
I2C × 2 (common use with serial 0, 1; single master)

 DMA controller
4-ch.
DMA transfer enabled between memory and memory or memory and peripheral register by set interrupt factor and software activation setting
Transfer unit : bytes/word
Transfer mode : 1 word/burst (max. 128 K bytes)
Transfer addressing : source/destination pointer fix/increment
High-speed transfer enabled between USB-FIFO and internal RAM in single address mode

 USB Functions
Conforms to USB1.1.
USB transceiver built-in
Full-speed (12 Mbps) supported.
9 end points (FIFO built-in independently)
FIFO size
(EP0, 1, 2, 3, 4, 5, 6, 7, 8) : 64, 128, 128, 128, 128, 128, 128, 128, 128 bytes
・EP0
Control transfer
IN/OUT (two ways)
・EP1 to EP8
Interrupt/Bulk/Isochronous transfer supported.
Settable to IN or OUT.
Double Buffering function supported.
When the MAXP size is set to a half or less of the MAXFIFO size for each EP, the Double Buffering function is made valid automatically.

 I/O Pins
I/O 77 : Common use : 77 (pull-up resistance specifiable)
152 MAE00011JEM
 MN102H74D, MN102H74G, MN102HF74G

 A/D converter
10-bit × 8-ch. (with S/H)

 Special Ports
USB ports (D+, D-)

 Notes
4 multiply PLL built-in, generation of internal 48 MHz at external oscillation 12 MHz

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
VI = VDD or VSS, output open
Operating supply current IDDopr 65+10α* mA
f = 12 MHz , VDD = 3.3 V
Supply current at STOP IDDS Pin with pull-up resistor is open all other input pins and Hi-Z 70 µA
state input/output pins are simultaneously applied VDD or
VSS level
Supply current at HALT IDDH f = 12 MHz , VDD = 3.3 V, output open 30+10α* mA
(Ta = –20°C to +70°C , VDD = 3.3 V, VSS = 0 V)
Note) * "α" depends on products. MN102H74D, MN102H74G α= 0; MN102HF74G α = 1

 Pin Assignment
LQFP100-P-1414

P80, TM10IOA, WDOUT

PA1, SBO1, AN5, SDA1
PA2, SBT1, AN6, SCL1

P83, SBO2, TM11IOA

P81, TM10IOB, STOP

P84, SBT2, TM11IOB
P92, AN2, TM13IOA

P90, AN0, TM12IOA

P93, AN3, TM13IOB

P91, AN1, TM12IOB

PA4, SBO0, SDA0
PA5, SBT0, SCL0

PA3, SBI0, AN7

PA0, SBI1, AN4

VDD (VPP)

USBMODE
P82, SBI2
/NMI

VDD
VSS

VSS

D+
D-
*
*
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51

PB0, /IRQ0 76 50 /CS3S, (TM9IO), SBT3, P72

PB1, /IRQ1 77 49 /CS2S, (TM8IO), SBO3, P71
PB2, /IRQ2 78 48 /CS1S, (TM7IO), SBI3, P70
PB3, /IRQ3 79 47 /CS0S, (TM6IO), A23, P47
PB4, /IRQ4 80 46 (TM5IO), A22, P46
PB5, /IRQ5 81 45 (TM4IO), A21, P45
/RST 82 44 (TM3IO), A20, P44
VDD 83 43 VSS
P00, D00 84 42 (TM2IO), A19, P43
P01, D01 85 41 A18, P42
P02, D02 86 40 A17, P41
P03, D03 87 39 A16, P40
P04, D04 88 38 A15, P37
P05, D05 89 37 A14, P36
P06, D06 90 36 A13, P35
P07, D07 91 35 A12, P34
VSS 92 34 VDD
P10, D08, (TM2IO) 93 33 A11, P33
P11, D09, (TM3IO) 94 32 A10, P32
P12, D10, (TM4IO) 95 31 A09, P31
P13, D11, (TM5IO) 96 30 A08, P30
P14, D12, (TM6IO) 97 29 A07, P27
P15, D13, (TM7IO) 98 28 A06, P26
P16, D14, (TM8IO) 99 27 A05, P25
P17, D15, (TM9IO) 100 26 A04, P24
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
/RE, P51
/WEL, P52
/WEH, P53
/CS0, P60
/CS1, P61
/CS2, P62
/CS3, P63
TM0IO, /BREQ, P64
TM1IO, /BRACK, P65
/WR, P66
/WORD, P67
A00, P20
A01, P21
A02, P22
A03, P23
VDD
BOSC, SYSCLK, P54
VSS
XI
XO
VDD
OSCI
OSCO
MODE
WAIT, P50

Note) *: Use 4.7 kW to 10 kW

MAE00011JEM 153
154
 AM3 (MN103) Series

The AM3 (MN103) Series of 32-bit microcomputers covers a broad

range of applications from equipment controllers
through multimedia processing.
The combination of a C language oriented architecture and optimizing
compiler delivers both high performance
and lower power consumption.
To streamline the development of applications high in both performance
and functionality, these devices incorporate
the AM Series standard on-chip I/O bus (C-bus) and the extended
calculation instruction function for
adapting them for ASSP enhancement and ASIC microcomputer
development.
The AM32 Series are for controller applications.

Features
• 32-bit C language architecture
Simple and highly efficient command sets
High code generation efficiency of commands by 1 byte basic word
length
High speed command execution by 5-step pipeline configured
load/store architecture
High speed execution of branch commands
• Extension calculation function meeting multimedia requirements
• Optimized C language compiler that generates high-speed
command codes
 Application
 MN103SB5 Series
Type MN103SFB5K
Internal ROM type FLASH
ROM (byte) 256K
RAM (byte) 8K
Package (Lead-free) LQFP064-P-1414
Minimum Instruction 20.9 ns (at 3.0 V to 3.6 V, 48 MHz, When USB used)
Execution Time 16.7 ns (at 2.7 V to 3.6 V, 60 MHz, When USB unused)

 Interrupts
RESET. IRQ × 4. Timer × 10. I2C × 1. SIF × 4. DMA × 12. WDT. System error. USB × 2

 Timer Counter
8-bit timer × 4
Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer)
16-bit timer × 2
Up-down count. Input capture. PWM output. Compare/capture register 2 channnels
Watchdog timer × 1

 Serial interface
Multi-master I2C × 1
UART/Synchronous interface selective × 2

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Serial transmission/reception. I2C transmission/reception. Software. USB transmission/reception
end
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

 USB HOST Controller

Conforms to USB 2.0: Full-speed (12 Mbps) supported
OHCI R1.0a standard conforming. External power supply control function. USB transceiver built-in

 I/O Pins
I/O 8 : (5 V I/O) Common use
33 : (3 V I/O) Common use
Input 1 : (3 V I/O) Common use

 ROM Correction
4 channels

156 MAF00024FEM
 MN103SFB5K

 Pin Assignment
LQFP064-P-1414

P81, TM10IOA
P83, TM11IOA
P82, TM10IOB
P84, TM11IOB
P33, SDA3

P35, SCL3

VDD18

VDD33
VSS
P34

P77
P40
P87

P86

P85

P75
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
VDD5 49 32 P74
PF5, TM7IO 50 31 P73
PF4, TM6IO 51 30 P72
P21 52 29 P71
VSS 53 28 P70
PD5, IRQ2 54 27 P67
PD4, IRQ1 55 26 P66
PD2, SBT2 56 25 P00
PD1, SBI2 57 24 P01
PD0, SBO2 58 23 P02
P92, SBT0 59 22 P03
P91, SBI0 60 21 P04
P90, SBO0 61 20 P05
VDD18 62 19 OCD_SCL
PA7 63 18 OCD_SDA
PA6 64 17 PB0, VPP
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9
PD6, IRQ3
USBNOC, PC0

USBD-

USBD+

PE0, IRQ0
VDD33
VDD18, VOUT
OSCI
OSCO
VSS
NRST
MMOD0
MMOD1
USBNPP, PC1

AVSS

AVDD

MAF00024FEM 157
 MN103SE5 Series
Type MN103SFE5P
Internal ROM type FLASH
ROM (byte) 624K
RAM (byte) 32K
Package (Lead-free) LQFP048-P2-0707A
Minimum Instruction 20.9 ns (at 3.0 V to 3.6 V, 48 MHz)
Execution Time

 Interrupts
RESET. IRQ × 3. Timer × 12. I2C × 7. SIF × 8. DMA × 12. Stream DMA × 1. WDT. System error. USB × 2. I2S × 1

 Timer Counter
8-bit timer × 6
Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer)
16-bit timer × 2
Up-down count. Input capture. PWM output. Compare/capture register 2 channnels
Watchdog timer × 1

 Serial interface
Multi-master I2C × 2
UART/Synchronous interface selective × 4

 Audio Output Interface

I2S interface × 1

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Serial transmission/reception. I2C transmission/reception. Software. USB transmission/reception
end. I2S empty
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

 Stream DMA controller

Number of channels: 1 channels
Unit of transfer: 8/32 bits
Maximum transfer cycles: 65535
Transfer source: Interface RAM
Transfer destination: Serial I/F. Audio output interface

 USB HOST Controller

Conforms to USB 2.0: Full-speed (12 Mbps) supported
OHCI R1.0a standard conforming. External power supply control function. USB transceiver built-in

 I/O Pins
I/O 27 : (3 V I/O) Common use

158 MAF00030DEM
MAF00030DEM
 Pin Assignment
LQFP048-P2-0707A

P83, TM11IOA, IRQ3, MCLK

P07, TRCD3
P06, TRCD2
P05, TRCD1
P04, TRCD0
VSS
P03, TRCST
P02, TRCCLK
P01, EXTRG1
P00, EXTRG0
OCD_SCL
OCD_SDA

48
47
46
45
44
43
42
41
40
39
38
37

P81, TM10IOA, SCL5 1 36 MMOD1

P82, TM10IOB, SDA5 2 35 MMOD0
P84, TM11IOB, SBO1, BCKA 3 34 VDDI, VOUT
P85, TM6IO, SBI1, SRDATAA 4 33 VDD3
P86, TM7IO, SBT1, LRCLKA 5 32 OSCO
P33, SBO3, SDA3 6 31 OSCI
P34, SBI3 7 30 AVDD
P35, SBT3, SCL3, CLK0 8 29 USBD+
P92, SBT0, BCKB 9 28 AVSS
P90, SBO0, SRDATAB 10 27 USBD-
P91, SBI0 11 26 USBNPP, USBPP, PC1
VDD3 12 25 USBNOC, PC0
13
14
15
16
17
18
19
20
21
22
23
24

VSS

VDDI
NRST
VDD3
VDD3

VPPEX
VDD18

PD1, SBI2
PD4, IRQ1
PD2, SBT2

PD0, SBO2
PD5, IRQ2, LRCLKB
MN103SFE5P

159
 MN103SG2 Series
Type MN103SG20L
Internal ROM type External
ROM (byte) 
RAM (byte) 32K
Package (Lead-free) QFP100-P-1818B (Under development)
Minimum Instruction 20.9 ns (at 3.0 V to 3.6 V, 48 MHz)
Execution Time

 Interrupts
RESET. IRQ × 4. Timer × 12. I2C × 13. SIF × 10. DMA × 12. Stream DMA × 1. WDT. System error. USB × 2. SDIO × 2. I2S × 1

 Timer Counter
8-bit timer × 6
Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer)
16-bit timer × 2
Up-down count. Input capture. PWM output. Compare/capture register 2 channnels
Watchdog timer × 1

 Serial interface
Multi-master I2C × 3
UART/Synchronous interface selective × 5

 Audio Output Interface

I2S interface × 1

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Serial transmission/reception. I2C transmission/reception. Software. USB transmission/reception
end. I2S empty. SD transmission/reception
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

 Stream DMA controller

Number of channels: 1 channels
Unit of transfer: 8/32 bits
Maximum transfer cycles: 65535
Transfer source: Interface RAM
Transfer destination: Serial I/F. Audio output interface

 USB HOST Controller

Conforms to USB 2.0: Full-speed (12 Mbps) supported
OHCI R1.0a standard conforming. External power supply control function. USB transceiver built-in

 SD HOST Interface
Conforms to SD HOST Controller Standard Specification Ver 1.00
Correspond with Single Block transfer, Multiple Block transfer
Operation frequency: Max. 24 MHz

 I/O Pins
I/O 43 : (3 V I/O) Common use
1 : (3 V I/O) Exclusive

160 MAF00031CEM
MAF00031CEM
QFP100-P-1818B
 Pin Assignment

PA3, MSDWP
P83, TM11IOA, IRQ3, MCLK

D7
D6
D5
D4
D3
D2
D1
D0
VDD3
P07, TRCD3
P06, TRCD2
P05, TRCD1
P04, TRCD0
VSS
P03, TRCST
P02, TRCCLK
P01, EXTRG1
P00, EXTRG0
OCD_SCL
OCD_SDA
NWE1
NWE0
NRE

99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76

100
P81, TM10IOA, SCL5 1 75 P23, SBT4, SCL4A
P82, TM10IOB, SDA5 2 74 P22, SBI4, NCS2
P84, TM11IOB, SBO1, BCKA 3 73 P21, SBO4, SDA4A, NCS1
P85, TM6IO, SBI1, SRDATAA 4 72 NCS0
P86, TM7IO, SBT1, LRCLKA 5 71 MMOD1
D8 6 70 MMOD0
D9 7 69 PC7
D10 8 68 PC6, SBT3
D11 9 67 PC5, SBI3
D12 10 66 PC4, SBO3
D13 11 65 VDDI, VOUT
D14 12 64 VDD3
D15 13 63 OSCO
PA4, SDA4B, MSDCD 14 62 OSCI
P93, SDA3, MSDDAT3 15 61 AVDD
P94, SCL3, MSDDAT2 16 60 USBD+
P92, SBT0, BCKB 17 59 AVSS
P90, SBO0, SRDATAB 18 58 USBD-
P91, SBI0 19 57 USBNPP, USBPP, PC1
VDD3 20 56 USBNOC, PC0
PA5, SCL4B, MSDCLK 21 55 P74, A20
VSS 22 54 P73, A19
P95, MSDDAT1 23 53 P72, A18
P96, MSDDAT0, IRQ0 24 52 P71, A17
P97, MSDCMD 25 51 P70, A16

26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A11
A10
A12
A13
A14
A15

VSS

VDDI
NRST
VDD3

PD1, SBI2
PD4, IRQ1

PD2, SBT2

PD0, SBO2
PD5, IRQ2, LRCLKB
MN103SG20L

161
 MN103SH7 Series
Type MN103SFH7J MN103SH7J
Internal ROM type FLASH Mask ROM
ROM (byte) 192K
RAM (byte) 8K
Package (Lead-free) TQFP064-P-1010C
Minimum Instruction 20.9 ns (at 3.0 V to 3.6 V, 48 MHz, When USB used)
Execution Time 16.7 ns (at 2.7 V to 3.6 V, 60 MHz, When USB unused)

 Interrupts
RESET. IRQ × 4. Timer × 10. I2C × 1. SIF × 4. DMA × 12. WDT. System error. USB × 2

 Timer Counter
8-bit timer × 4
Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer)
16-bit timer × 2
Up-down count. Input capture. PWM output. Compare/capture register 2 channnels
Watchdog timer × 1

 Serial interface
Multi-master I2C × 1
UART/Synchronous interface selective × 2

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Serial transmission/reception. I2C transmission/reception. Software. USB transmission/reception
end
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

 USB HOST Controller

Conforms to USB 2.0: Full-speed (12 Mbps) supported
OHCI R1.0a standard conforming. External power supply control function. USB transceiver built-in

 I/O Pins
I/O 41 : (3 V I/O) Common use
Input 1 : (3 V I/O) Common use

 ROM Correction
4 channels

162 MAF00036AEM
 MN103SH7J, MN103SFH7J

 Pin Assignment
TQFP064-P-1010C

P81, TM10IOA
P83, TM11IOA
P82, TM10IOB
P84, TM11IOB
P33, SDA3

P35, SCL3

VDD18

VDD33
VSS
P34

P77
P40
P87

P86

P85

P75
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
VDD33 49 32 P74
PF5, TM7IO 50 31 P73
PF4, TM6IO 51 30 P72
P21 52 29 P71
VSS 53 28 P70
PD5, IRQ2 54 27 P67
PD4, IRQ1 55 26 P66
PD2, SBT2 56 25 P00
PD1, SBI2 57 24 P01
PD0, SBO2 58 23 P02
P92, SBT0 59 22 P03
P91, SBI0 60 21 P04
P90, SBO0 61 20 P05
VDD18 62 19 OCD_SCL
PA7 63 18 OCD_SDA
PA6 64 17 PB0, VPP
10

12
13
14
15
16
11
1
2
3
4
5
6
7
8
9
PD6, IRQ3
USBNOC, PC0

USBD-

USBD+

PE0, IRQ0
VDD33
VDD18, VOUT
OSCI
OSCO
VSS
NRST
MMOD0
MMOD1
USBNPP, PC1

AVSS

AVDD

MAF00036AEM 163
 MN103L06 Series
Type MN103LF06N
Internal ROM type FLASH
ROM (byte) 512K
RAM (byte) 32K
Package (Lead-free) LQFP100-P-1414 (Under development), QFP100-P-1818B (Under development)
Minimum Instruction 25 ns (at 2.6 V to 3.6 V, 40 MHz)
Execution Time

 Interrupts
RESET. IRQ × 8. NMI. Timer × 23. I2C × 10. SIF × 10. DMA × 12. WDT. A/D. Time base timer × 2. System error. Key input. Remote
control × 4. CEC × 2. RTC × 2

 Timer Counter
8-bit timer × 11
Timer 0, 4 ..............Square-wave output. PWM output. Event count. Simple pulse width measurement
Timer 1 ..................Square-wave output. Event count
Timer 2 ..................Square-wave output. PWM output. Event count. Serial transfer clock output
Timer 3 ..................Square-wave output. Event count. Serial transfer clock output
Timer 6 ..................8-bit freerun timer
Timer A, B, C, D, E Serial transfer clock output
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 0, 1, 2 can be cascade-connected
Timer 0, 1, 2, 3 can be cascade-connected
16-bit timer × 6
Timer 7 ..................Square-wave output. High accuracy PWM output (cycle/duty continuous variable). Event count. Input capture
Timer 8 to 12 .........Square-wave output. Event count. Input capture. PWM output
24H timer: Interval function (Interruption every 0.5 seconds, every 1 second, every 1 minute, every 1 hour and 24 hours). Alarm function
Time base timer
Watchdog timer

 Serial interface
Multi-master I2C/UART (full duplex) /Synchronous interfaces selective × 5: max 10 channels

 HDMI-CEC/AV-Link
Number of channels: 2 channels (Correspondence with AV-Link mode1 or mode3:1channel)
Communication mode: Correspondence with CEC communication option (HDMI format)

 Remote Contorol Interface

Remote control reception: Correspondence with AEHA (Association for Electric Home Appliances) format. Queued reception by low
speed clock

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Serial transmission/reception. A/D conversion finish. I2C transmission/reception. Time base
timer. Software. Remote control reception
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

 I/O Pins
I/O 22 : (5 V I/F)
59 : (3.3 V I/F)
Input 2 : (3.3 V I/F)

 A/D converter
10-bit × 15 channels

164 MAF00035AEM
 MN103LF06N

 Reset
Low voltage detection. Automatic Reset

 Pin Assignment
LQFP100-P-1414, QFP100-P-1818B

P42, SBT4A, SCL4A, IRQ7, NMIRQ

P40, SBI4A, TM11IOB, D15

P41, SBO4A, SDA4A, IRQ6

P85, LED5, TM10IOA, D12

P87, LED7, TM11IOA, D14
P86, LED6, TM10IOB, D13

P83, LED3, TM9IOA, D10

P84, LED4, TM9IOB, D11

P81, LED1, TM8IOA, D8

P82, LED2, TM8IOB, D9

P80, LED0, TM3IO

P67, KEY7, D1
P66, KEY6, D0
P65, KEY5, A0
P64, KEY4, A1
P75, D7
P74, D6
P73, D5
P72, D4
P71, D3
P70, D2
VDD18

VDD33
VSS
P77
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
P90, SBO5B, SDA5B 76 50 P63, KEY3, A2
P91, SBI5B 77 49 P62, KEY2, A3
P92, SBT5B, SCL5B 78 48 P61, KEY1, A4
P93, SBO3B, SDA3B 79 47 P60, KEY0, A5
P94, SBI3B 80 46 P57, SBT2C, SCL2C, A6
P95, SBT3B, SCL3B 81 45 P56, SBI2C, A7
PD0, SBO2B, SDA2B 82 44 P55, SB02C, SDA2C, A8
PD1, SBI2B 83 43 P54, SBT4B, SCL4B, A9
PD2, SBT2B, SCL2B 84 42 P53, SBI4B, A10
PD3, IRQ0B 85 41 P52, SBO4B, SDA4B, A11
PD4, IRQ1B 86 40 P51, A12
PD5, IRQ2B 87 39 VSS
PD6, IRQ3B, TM12IOA 88 38 P50, A13
VDD5 89 37 VDD18
PD7, IRQ4B, TM12IOB 90 36 P35, SBT3A, SCL3A, A14
VSS 91 35 P34, SBI3A, TM4IO, A15
PA0, AN0 92 34 P33, SBO3A, SDA3A, A16
PA1, AN1 93 33 P32, SBT6A, SCL6A, A17
PA2, AN2 94 32 P31, SBI6A, A18
PA3, AN3 95 31 P30, SBO6A, SDA6A, A19
PA4, AN4 96 30 P25, IRQ5A, A20
PA5, AN5 97 29 P24, IRQ4A, NCS4
PA6, AN6 98 28 P23, IRQ3A, NCS3
PA7, AN7 99 27 P22, IRQ2A, NCS2
VREFH 100 26 P21, IRQ1A, RMIN, NCS1
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
P02, SBT5A, SCL5A, AN10, NRE

OSCI, P13
P00, SBO5A, SDA5A, AN8, NWE0
P01, SBI5A, AN9, NWE1

P04, SBI2A, CEC0

P10, TM0IO, AN12, (OCD_SDA)

P12, TM2IO, AN14, SYSCLK

MMOD
OSCO

VSS
XI, P07
XO
VDD33
VDD18, VOUT
NRST
LON
P14, SBO6B, SDA6B, TM7IOA
P15, SBI6B, TM7OB
P16, SBT6B, SCL6B, TM7OC
NOCDMOD
P20, IRQ0A, NDK, (VPP)
P06, IRQ5B, AN11

P11, TM1IO, AN13, (OCD_SCL)

P03, SBO2A, SDA2A, CECAVL1A

P05, SBT2A, SCL2A, CECAVLB1B

MAF00035AEM 165
 MN103S57 Series
Type MN103S57G MN103SF57G
Internal ROM type Mask ROM FLASH
ROM (byte) 128K
RAM (byte) 16K
Package (Lead-free) LQFP100-P-1414A
Minimum Instruction 25.0 ns (at 3.0 V to 3.6 V, 40 MHz)
Execution Time

 Interrupts
RESET. IRQ × 8. NMI. Timer × 28. I2C × 2. SIF × 10. DMA × 12. WDT. A/D. System error

 Timer Counter
8-bit timer × 10
Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer)
16-bit timer × 6
Up-down count. Input capture. PWM output. Compare/capture register 2 channnels
Watchdog timer × 1

 Serial interface
UART/Synchronous/Multi-master I2C interface selective × 2
UART/Synchronous interface selective × 3

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Serial transmission/reception. A/D conversion finish. I2C transmission/reception. External
transmission request. Software
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

 Extended Calculation
Multiply and accumulate arithmetic. Multiplication. Saturated arithmetic

 I/O Pins
I/O 73 : Common use

 A/D converter
10-bit × 12 channels

 ROM Correction
4 channels

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Non-linear error 10-bit. VREFH = 3.3 V ±4 LSB
A/D conversion time IOCLK = 20 MHz. TAD = 200 ns 2.4 µs
Analog input voltage AVSS VREFH V
Ta = 25 °C. VDD = PVDD = AVDD = 3.3 V. VSS = PVSS = AVSS = 0 V
Note) TAD is A/D conversion clock cycle

166 MAF00009HEM
 MN103S57G, MN103SF57G

 Pin Assignment
LQFP100-P-1414A

P85, SBT1, TM15IOB, TM9IO, SCL1

P75, SBT4, ADTRG

P72, SBT3, AN10
P73, SBI4, AN11
P71, SBO3, AN9

P64, AN4, IRQ4

P65, AN5, IRQ5
P66, AN6, IRQ6
P67, AN7, IRQ7
P70, SBI3, AN8

P74, SBO4

EXMOD0
EXMOD1

P60, AN0
P61, AN1
P62, AN2
P63, AN3
MMOD0
MMOD1

NMIRQ

VREFH
AVDD
AVSS
VDD

VSS
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
P84, SBO1, TM15IOA, TM8IO, SDA1 76 50 PVSS
P83, SBI1, TM14IOB, TM7IO 77 49 TCPOUT
P82, SBT0, TM14IOA, TM6IO, SCL0 78 48 PVDD
P81, SBO0, TM13IOB, TM5IO, SDA0 79 47 OSCI
P80, SBI0, TM13IOA, TM4IO 80 46 OSCO
P97, D15, TM12IOB 81 45 VSS
P96, D14, TM12IOA 82 44 VDD
P95, D13, TM11IOB 83 43 RST
P94, D12, TM11IOA 84 42 P50, CKSEL
P93, D11, TM10IOB 85 41 P51, BG
P92, D10, TM10IOA 86 40 P52, BR
P91, D9, IRQ1 87 39 P53, DK
VSS 88 38 P40, WDTOVF
VDD 89 37 P41, SBI2
P90, D8, IRQ0 90 36 P42, SBO2
PA7, D7 91 35 P43, SBT2
PA6, D6 92 34 VSS
PA5, D5 93 33 P30, SYSCLK
PA4, D4 94 32 VDD
VSS 95 31 VPP
PA3, D3 96 30 P31, CS0
PA2, D2 97 29 P32, CS1
PA1, AS, D1 98 28 P33, CS2
PA0, RWSEL, D0 99 27 P34, CS3
PB0, IRQ3, DREQ1 100 26 P35, RE
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
P03, IRQ2, DREQ0, A19
P02, A18
P01, A17
P00, A16
P17, ADM15, A15
P16, ADM14, A14
VDD
P15, ADM13, A13
P14, ADM12, A12

P12, ADM10, A10

P10, ADM8, A8
P27, ADM7, A7
P26, ADM6, A6
VDD
VSS
P25, ADM5, A5
P24, ADM4, A4
P23, ADM3, A3
P22, ADM2, A2
P21, ADM1, A1
P20, ADM0, A0
P37, WE1
P36, WE0
P11, ADM9, A9
P13, ADM11, A11

Note) Connect TCPOUT with VSS.

MAF00009HEM 167
 MN103S73 Series
Type MN103SF73N MN103SF73R
Internal ROM type FLASH
ROM (byte) 512K 1024K
RAM (byte) 32K
Package (Lead-free) QFP100-P-1818B
Minimum Instruction 25 ns (at 2.7 V to 3.6 V, 40 MHz)
Execution Time

 Interrupts
RESET. IRQ × 8. NMI. Timer × 28. I2C × 3. SIF × 10. DMA × 12. WDT. A/D. Time base timer × 2. System error. Remote control × 4

 Timer Counter
8-bit timer × 10
Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer)
16-bit timer × 6
Up-down count. Input capture. PWM output. Compare/capture register 2 channnels
Time base timer × 1
Watchdog timer × 1

 Serial interface
UART/Synchronous/Multi-master I2C interface selective × 3
UART/Synchronous interface selective × 2

 Remote Contorol Interface

Remote control reception: Correspondence with AEHA (Association for Electric Home Appliances) format. Queued reception by low
speed clock

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Serial transmission/reception. A/D conversion finish. I2C transmission/reception. Software.
Remote control data reception
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

 I/O Pins
I/O 22 : (5 V I/O) Common use
59 : (3 V I/O) Common use
Input 1 : (3 V I/O) Common use

 A/D converter
10-bit × 8 channels. 5 V input

 ROM Correction
8 channels

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Resolution 10 Bits
Non-linear error VDD5 = VREFH = 3.3 V. VSS = 0 V ±4 LSB
Differential non-linearity error VDD5 = VREFH = 5.0 V. VSS = 0 V ±4 LSB

168 MAF00021EEM
 MN103SF73N, MN103SF73R

 Pin Assignment
QFP100-P-1818B

P42, SBT4, SCL4, IRQ7, NMIRQ

P40, SBI4, TM13IOB, D15

P41, SBO4, SDA4, IRQ6

P87, TM13IOA, D14

P85, TM12IOA, D12

P83, TM11IOA, D10

P86, TM12IOB, D13

P84, TM11IOB, D11

P81, TM10IOA, D8
P82, TM10IOB, D9

P77, SDCLKO
P80, SDCLKI

P75, D7
P74, D6
P73, D5
P72, D4
P71, D3
P70, D2
P67, D1
P66, D0
P65, A0
P64, A1
VDD18

VDD33
VSS
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
P90, SBO0B 76 50 P63, A2
P91, SBI0B 77 49 P62, A3
P92, SBT0B 78 48 P61, A4
P93, SBO3B, SDA3B 79 47 P60, A5
P94, SBI3B 80 46 P57, A6
P95, SBT3B, SCL3B 81 45 P56, A7
PD0, SBO2B, SDA2B 82 44 P55, A8
PD1, SBI2B 83 43 P54, A9
PD2, SBT2B, SCL2B 84 42 P53, A10
PD3, IRQ0B 85 41 P52, A11
PD4, IRQ1B 86 40 P51, A12
PD5, IRQ2B 87 39 VSS
PD6, IRQ3B, TM15IOA 88 38 P50, A13
VDD5 89 37 VDD18
PD7, IRQ4B, TM15IOB 90 36 P35, SBT3A, SCL3A, A14
VSS 91 35 P34, SBI3A, A15
PA0, AN0 92 34 P33, SBO3A, SDA3A, A16
PA1, AN1 93 33 P32, SBT1A, A17
PA2, AN2 94 32 P31, SBI1A, A18
PA3, AN3 95 31 P30, SBO1A, A19
PA4, AN4 96 30 P25, IRQ5A, A20
PA5, AN5 97 29 P24, IRQ4A, NCS3
PA6, AN6 98 28 P23, IRQ3A, NCS2
PA7, AN7 99 27 P22, IRQ2A, NCS1
VREFH 100 26 P21, IRQ1A, RMIN, NCS0
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
P00, SBO0A, NWE0, NSDQM0
P01, SBI0A, NWE1, NSDQM1
P02, SBT0A, NRE
P03, SBO2A, SDA2A, NSWE
P04, SBI2A, SCKE
P05, SBT2A, SCL2A, NSCAS
P06, IRQ5B, NSRAS
P10, TM4IO, OCD_SDA

P12, TM6IO, SYSCLK

MMOD
OSCO
OSCI
VSS
XI, P07
XO
VDD33
VDD18, VOUT
NRST
LON
P14, SBT1B, TM14IOA
P15, SBO1B, TM14IOB
P16, SBI1B, TM7IO
OCDMOD
P20, IRQ0A, DK(VPP)
P11, TM5IO, OCD_SCL

Note) VDD5 = VDD33 to 5.5 V. VDD33 = 2.7 V to 3.6 V

MAF00021EEM 169
 MN103S97 Series
Type MN103S97N MN103SF66R
Internal ROM type Mask ROM FLASH
ROM (byte) 512K 1024K
RAM (byte) 24K 40K
Package (Lead-free) MBGA255-C-1111A
Minimum Instruction 25 ns (at 1.65 V to 1.95 V, 40 MHz)
Execution Time

 Interrupts
RESET. IRQ × 11. NMI. Key input. Timer × 40. Input capture × 16. PWM × 5. SIF × 17. DMA × 12. WDT. A/D. System error

 Timer Counter
8-bit timer × 8
Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer)
8-bit timer with PWM × 8
Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer). PWM output
16-bit timer × 6
Up-down count. Input capture. PWM output. Compare/capture register 2 channnels
16-bit timer × 6
Reload-down count
Watchdog timer × 1

 Serial interface
UART/Synchronous interface selective × 6: Serial 0, 1, 3 to 6
Start-stop synchronization/Synchronization commonly used (16 bytes containing transmission/reception FIFO): Serial 2
I2C serial interface, multi master transmission/reception function × 1

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65,535
Starting factor: External interrupt. Timer. PWM. Serial transmission/reception. A/D conversion finish. Software
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

 I/O Pins
I/O 170 : Common use
Input 25 : Common use

 A/D converter
10-bit × 25 channels

 PWM
12/14-bit resolution × 5 channels

 ICR
28-bit × 13 channels + 16-bit × 6 channels (common with timer)

 OCR
16-bit × 12 channels (common with timer)

 Timer Synchronous Output

4-bit (synchronous output) × 2 channels

 ROM Correction
8 channels

170 MAF00017GEM
 MN103S97N, MN103SF66R

 Electrical Charactreistics (Supply current)

Limit
Parameter Symbol Condition Unit
min typ max
Operating Supply current IDD1 VDD = 1.95 V 65 100 mA
(VDD)
VDDB, VDDH, AVDD = 3.6 V
Operating Supply current fosc = 15 MHz. PLL = ON. LON = L
IDD6 30 55 mA
(VDDH, AVDD)
Supply current at STOP IDD5 VDD = 1.95 V 210 µA
(VDD) VDDB, VDDH, AVDD = 3.6 V
Supply current at STOP fosc = oscillation stopped. LON = L
IDD14 Tj = 85 °C 50 µA
(VDDH, AVDD)
Ta = -20 °C to +85 °C. VSS = AVSS = 0.0 V

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Resolution 10 Bits
Non-linear error AVDD = 3.3 V. VSS = AVSS = 0.0 V ±4 LSB
A/D conversion time IOCLK = 20 MHz. TAD = 200 ns 2.4 µs
Ta = 25 °C. AVDD = 3.3 V. AVSS = 0.0 V
Note) TAD is A/D conversion clock cycle

MAF00017GEM 171
 Pin Assignment
MBGA255-C-1111A
PL4, PM1, PM0, PN0, PO1 PP4, PP7, PQ5, PQ7, PP5, PR5, PR7, PS5, PT0,
N.D. A12, ICR1 ICR0 ICR8 D4 D7 D13 D15 D5 TM22IOB TM23IOB /BG A16 N.D.
ADM12 T
PL3, PL6, PM3, PM4, PM2, PN2, PP1, PQ1, PQ6, PR4, PR3, PS3, PS2, PT2, PU5, PU7,
A11, A14, ICR3 ICR4 ICR2 ICR10 D1 D9 D14 TM22IOA TM21IOB /WE2 WDOVF A18 A24, KI7
ADM11 ADM14 KI5 R
PK7, PL7, PM7, PM6, PM5, PN4, PP3, PQ3, PR1, PS1 PU1, PU3, PT1, PU2, P03, PU0,
A7, A15, ICR7 ICR6 ICR5 ICR12 D3 D11 TM20IOB A20, A22, A17 A21, D19, A19,
ADM7 ADM15 KI1 KI3 KI2 SBI1 KI0 P
PK5, PK4, PO0 PN1, PL5, PL1, PP0, PP6, PQ0, PQ4, PS4, PR0, P01, P05, P04, P13,
A5, A4, ICR9 A13, A9, D0 D6 D8 D12 /WE3 TM20IOA D17, D21, D20, D27,
ADM5 ADM4 ADM13 ADM9 SBO0 SBT1 SBO1 SBO3 N
PJ5, PL0, PJ3, PL2, PK6, PN3, PP2, PQ2, PR6, PR2, PS0, PU4, P07, P12, PU6, P00,
AS A8, /RE A10, A6, ICR11 D2 D10 TM23IOA TM21IOA PWM4 A23, D23, D26, A25, D16,
ADM8 ADM10 ADM6 KI4 SBI2 SBI3 KI6 SBI0 M
PI1, PJ4, PK3, PK1, PK2, PK0, PS6, P10, P11, P14, P06, P02,
CS1 DK A3, A1, A2, A0, VDDB VDDB VDDB VSS /BR D24, D25, D28, D22 D18,
ADM3 ADM1 ADM2 ADM0 SBO2 SBT2 SBT3 SBT0 L
*2 PI5, PJ1, PJ2, PI2, PJ0, P20, P21, *1 P16, P15,
N.C. RWSEL /WE1 SYSCLK /CS2 /WE0 VSS VDDH VDD VDD SBI4 SBO4 N.C. D30 VDDB D29
[ VREFH] (VDDH) K
PG5, PI0, PI3, PH0, PI4, P31, P36, P24, P23, P22, P17,
AVDD AN21 /CS0 /CS3 AN24 /CS4 VSS VDDH VDD VSS IRQ1 IRQ6 SBO5 SBI5 SBT4 D31
J
PG2, PG4, PG1, PG6, PG0, PG3, P33, P25, P34,
AN18 AN20 AN17 AN22 AN16 AN19 VSS VDDH VDD VSS IRQ3 SBT5 IRQ4 VSS VDDH OSCI
H
PF4, PF0, PG7, PF6, PF1, PF5, *3 P35, *3 *3 P32,
AN12 AN8 AN23 AN14 AN9 AN13 VSS VDDH VOUT VSS N.C. IRQ5 N.C. N.C. IRQ2 OSCO
G
PF2, PE4, PE7, PE6, PF3, PE3, P82, P41, P37, P50, P30, *4
AN10 AN4 AN7 AN6 AN11 AN3 SY0OT2 VSS VSS VSS IRQ9 IRQ7 /NMIRQ MMOD1 IRQ0 N.C.
F
PE2, PE0, PE1, PF7, PE5, PB1, P90, P80, P66, P72, *6 P70, P53, P42, *5
AN2 AN0 AN1 AN15 AN5 TM1IO, SBI6 SY0OT0 TM36IO TM12IO N.C. TM10IO MMOD0 FRQS0 IRQ10 N.C.
PWM2 [ TRCD1] E
PD3, PD1, PC5, PA0, P94 P92, P84, P74, P73, P64, P62, *6 *3 P52, P51, P40,
TM25IOB TM24IOB SCL0 ADTRG SBT6 SY1OT0 TM14IO TM13IO TM34IO TM32IO N.C. N.C. EXMOD1 EXMOD0 IRQ8
[ EXTRG1 ] D
PC1 PD0, PB5, PB7, PB4, P93 P85, P63, *6 *6 *6
AVSS TM24IOA TM5IO TM7IO TM4IO SY1OT1 TM33IO N.C. N.C. TDO N.C. /NRST FRQS1 N.D.
[ EXTRG0 ] [TRCCLK ] [TRCST ] C
PC3, PD2, PC4, PB3, PB6, P95 P87, P86, P75, P65, *6 P60, *6
PWM0 TM25IOA SDA0 TM3IO TM6IO SY1OT3 SY1OT2 TM15IO TM35IO N.C. TM30IO N.C. TMS /TRST CKSEL,
[TRCD0 ] [ TRCD3 ] P55 B
PC2 PC0 PB2, PB0, P91, P83, P81, P71, P67, P61, *6
N.D. TM2IO, TM0IO, SBO6 SY0OT3 SY0OT1 TM11IO TM37IO TM31IO N.C. TCK TDI LON N.D.
PWM3 PWM1 [ TRCD2 ] A

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Perspective

Note) Not Defined has an electrode (pin) but Not Defined is not guaranteed.Please design so as not to cause short circuit with other
wiring on the user board.Each of VDD, VDDB, VDDH, and VSS has multiple electrodes (pins). Connect the same electrode
names to the same power supply.[ ]: Not available with MN103S97N.
*1: Connect the K4 pin to the VDDH power for the MN103SF66R.
*2: Connect the K16 pins to the AVDD power for the MN103SF66R.
*3: D4, G3, G4 and G6 pins have signal electrodes for the MN103SF66R.Perform the necessary pin processing.
*4: F1 pin should be pull-down, or pull-up to the VDDH power for the MN103SF66R.
*5: E1 pin should be open for the MN103SF66R.
*6: A5, B4, B6, C4, C6, C7, D5 and E6 pins are debugging pins.Perform the necessary pin processing.

172 MAF00017GEM
173
 MN103SB9 Series
Type MN103SB9N MN103SFB9R
Internal ROM type Mask ROM FLASH
ROM (byte) 512K 1024K
RAM (byte) 32K
Package (Lead-free) TQFP128-P-1414A
Minimum Instruction 16.7 ns (at 2.7 V to 3.6 V, 60 MHz)
Execution Time

 Interrupts
RESET. IRQ × 9. NMI. Timer × 28. I2C × 3. SIF × 10. DMA × 12. WDT. A/D. Time base timer × 2. System error

 Timer Counter
8-bit timer × 10
Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer)
16-bit timer × 6
Up-down count. Input capture. PWM output. Compare/capture register 2 channnels
Time base timer × 1
Watchdog timer × 1

 Serial interface
UART/Synchronous/Multi-master I2C interface selective × 3
UART/Synchronous interface selective × 2

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Serial transmission/reception. A/D conversion finish. I2C transmission/reception. External
transmission request. Software
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

 Extended Calculation
Multiply and accumulate arithmetic. Multiplication. Saturated arithmetic

 I/O Pins
I/O 104 : Common use

 A/D converter
10-bit × 12 channels

 ROM Correction
8 channels

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Resolution 10 Bits
Non-linear error ±4 LSB
AVDD = 3.3 V. VSS = 0 V
Differential non-linearity error ±4 LSB

174 MAF00023DEM
 MN103SB9N, MN103SFB9R

 Pin Assignment
TQFP128-P-1414A

P70, SYSCLK

VOUT, VDDI

XI, P75
OSCO

VDD3
VDDI

OSCI
LON
VSS

VSS
P96
P95
P94
P93
P92
P91
P90
P87
P86
P85

P84
P83
P82
P81
P80
P71
P72
P73
P74

P33
P67
XO
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
P97 97 64 NRST
PA0 98 63 VSS
PA1 99 62 P66
PA2 100 61 VDDI
PA3 101 60 P65
PA4 102 59 P64
PA5 103 58 P63
PA6, DREQ0 104 57 P62
PA7, DREQ1 105 56 P61
VDD3 106 55 P60
PB0, IRQ0 107 54 P57, IRQ7
PB1, IRQ1 108 53 P56, IRQ6
PB2, IRQ2 109 52 P55, IRQ5
PB3, IRQ3 110 51 P54, IRQ4
PB4, TM10IOA, IRQ4 111 50 P53
PB5, TM10IOB, IRQ5 112 49 P52
PB6, TM11IOA, IRQ6 113 48 P51
PB7, TM11IOB, IRQ7 114 47 P50
PC0, DREQ0 115 46 VDD3
PC1, DREQ1 116 45 P47
PC2, TM12IOA 117 44 P46
PC3, TM12IOB 118 43 P45
PD0, SBI1, TM14IOB, TM7IO 119 42 P44
PD1, SBO1, TM15IOA, TM8IO, SDA1 120 41 P43
PD2, SBT1, TM15IOB, TM9IO, SCL1 121 40 P42
PD3, SBI0, TM13IOA, TM4IO 122 39 P41
PD4, SBO0, TM13IOB, TM5IO, SDA0 123 38 P40
PD5, SBT0, TM14IOA, TM6IO, SCL0 124 37 MEMMOD
VSS 125 36 MOD
VDDI 126 35 TMOD
VDD3 127 34 P35
VDD3 128 33 P34
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
11
1
2
3
4
5
6
7
8
9
PD6
P00, NMIRQ
P01, IRQ8
P02, SBI3
P03, SBO3
P04, SBT3
P05, SBI2
P06, SBO2, SDA2
P07, SBT2, SCL2
OCD_SCL, P36
OCD_SDA, P37

P31, CKSEL0
P10, AN0, SBI0

P12, AN2, SBT0, SCL0

VSS
P13, AN3
VDDI
P14, AN4, SBI1
P15, AN5, SBO1, SDA1
P16, AN6, SBT1, SCL1
P17, AN7
P20, AN8, SBI4
P21, AN9, SBO4
P22, AN10, SBT4

P24, DA0
P25, DA1
P26, ADTRG

P32
P11, AN1, SBO0, SDA0

P23, AN11
P30, WDOVF, CKSEL1

AVDD

MAF00023DEM 175
 MN103SD0 Series
Type MN103SD0Q MN103SFD0R
Internal ROM type Mask ROM FLASH
ROM (byte) 768K 1024K
RAM (byte) 32K 40K
Package (Lead-free) UBGA257-P-1111A
Minimum Instruction 16.7 ns (at 2.7 V to 3.6 V, 60 MHz)
Execution Time

 Interrupts
RESET. IRQ × 11. NMI. Key input. Timer × 32. Input capture × 16. PWM × 6. SIF × 24. I2C × 4. DMA × 18. WDT. A/D. System error

 Timer Counter
8-bit timer × 8
Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer)
16-bit timer × 6
Up-down count. Input capture. PWM output. Compare/capture register 2 channnels
16-bit timer × 6
Reload-down count
Watchdog timer × 1

 Serial interface
UART/Synchronous interface selective × 10: Serial 0, 1, 3 to A
Start-stop synchronization/Synchronization commonly used (16 bytes containing transmission/reception FIFO): Serial 2
I2C serial interface, multi master transmission/reception function × 2

 DMA controller
Number of channels: 6 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Input capture. PWM. Serial transmission/reception. I2C transmission/reception. A/D conversion
finish. Software
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

 I/O Pins
I/O 194 : Common use
Input 1 : Exclusive

 A/D converter
10-bit × 32 channels

 PWM
12/14-bit resolution × 6 channels

 ICR
28-bit × 13 channels + 16-bit × 6 channels (common with timer)

 OCR
16-bit × 12 channels (common with timer)

 Timer Synchronous Output

4-bit (synchronous output) × 2 channels

 ROM Correction
8 channels

176 MAF00026FEM
 MN103SD0Q, MN103SFD0R

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Resolution 10 Bits
Non-linear error VDD33 = 3.3 V. VSS = 0.0 V ±3 LSB
A/D conversion time IOCLK = 20 MHz. TAD = 200 ns 2.4 µs
Ta = 25 °C
Note) TAD is A/D conversion clock cycle

 Pin Assignment
UBGA257-P-1111A
A B C D E F G H J K L M N P R T U V W Y
PJ7, PJ5, PJ3, PJ1, PH3, PH4, PH0, PG0,
20 VDDL VDDL PN0, PM3, PL7, PL4, PL1, PK6, PK2, PK0, ADM15,
ADM13, ADM11, ADM9, VDDB VDDB 20
TM20IOA SY0OT3 TM7IO TM4IO SCL0 KI6 KI2 KI0 A15 SYSCLK DK NWE0 NCS0
A13 A11 A9
PJ6, PJ4, PJ2, PJ0, PH5,
19 VDDL VDDL PM7, PM5, PM1, PL6, PL3, PL0, PK4, PK1, ADM14,
ADM12, ADM10, ADM8,
PH2, PG3, PG1, VDDB VDDB 19
SY1OT3 SY1OT1 SY0OT1 TM6IO TM3IO SDA0 KI4 KI1 A14 AS NRE NCS3 NCS1
A12 A10 A8
PI7, PI5, PI3, PI1, PH6, PH1, PG2,
18 PN2, PN1, VDDL PM6, PM4, PM0, PL5, PL2 PK5, PK3, ADM7,
ADM5, ADM3, ADM1, VDDB PF7, PF6, 18
TM22IOA TM21IOA SY1OT2 SY1OT0 SY0OT0 TM5IO KI5 KI3 A7 RWSEL NWE1 NCS2 TM2IO TM1IO
A5 A3 A1
PI6, PI4, PI2, PI0,
17 PP0, PN4, PN3, VDDL PM2, VSS VDD18 PK7, VDD18 VSS ADM6, VSS PG4, VDDB PF5, PF4, PF2, 17
ADM4, ADM2, ADM0,
SBI7 TM21IOB TM20IOB SY0OT2 KI7 A6 A4 A2 A0 NCS4 TM0IO IRQ10 IRQ8

16 PP4, PP2, PP1, PN5, PF1, PF3, PF0, PE4 16

SBO8 SBT7 SBO7 TM22IOB IRQ7 IRQ9 IRQ6

15 PP7, PP5, PP6, PP3, PE3, PE5 PE2, PE0, 15

SBO9 SBT8 SBI9 SBI8 NBG NBR TM10IO
PD5,
14 PR2, PR0, PR1, VSS PD6, PE1, PD7, D13, 14
SBOA SBT9 SBIA D14 TM11IO D15 IRQ4
PD3, PD4, PD2,
13 PS0 PR4, PR5 PR3, VSS D11, D12, D10, 13
IRQ5 SBTA SBT6 IRQ3 SBO6
PS4, PS2, PS3, PC7, PD1, PD0, PC6,
12 PS1 D7, D9, D8, D6, 12
TM14IO TM12IO TM13IO SBO5 SBI6 SBT5 SBI5
PS5, PC4, PC5, PC3,
11 PS7 PS6 VDD33 VDD33 D4, D5, D3, 11
TM15IO SBO4 SBT4 SBI4
PC0, PC2,
10 P00, P02, P04, P01, PB5, PC1, D0, D2, 10
D1,
AN0 AN2 AN4 AN1 IRQ0 SBO3 SBI3 SBT3

9 P03, P05, P06, VSS VSS PB2, PB3, PB4, 9

AN3 AN5 AN6 SBI2 SBO2 SBT2

8 P07, P11, P12, P10, PA6, PB0, PA7, PB1, 8

AN7 AN9 AN10 AN8 A22 A24 A23 A25

7 P13, P15, P17, P14, VSS PA4, PA3, PA5, 7

AN11 AN13 AN15 AN12 A20 A19 A21

6 P16, P20, P24, P21, P96, PA1, PA0, PA2, 6

AN14 AN16 AN20 AN17 IRQ1 A17 A16 A18

5 P22, P23, P26, VSS VSS P85, P94, P95, P97, 5

AN18 AN19 AN22 PWM5 SBO1 SBT1 IRQ2

4 P25, P27, P30, VDD33 VSS VSS P53, VDD18 P76, VOUT VOUT VDD18 P71, P90, P91, P93,
N.C. VSS N.C. VDD33 4
AN21 AN23 AN24 TM23IOB NMI ICR9 SBI0 SBO0 SBI1

3 P32, P31, VDD33 P34, P36, P51, P56, P61, P63, MMOD P65, P67, P73, P82, VDD33 P92, P84, 3
OCD_SDA N.C. N.C.
AN26 AN25 AN28 AN30 TM24IOA SDA1 ICR1 ICR3 ICR5 ICR7 ICR11 PWM2 SBT0 PWM4

2 VDD33 VDD33 P33, P35, P41, P50, P54, P57, P62, VSS NRST P66, P72, N.C. N.C. N.C. P80, P83, VDD33 VDD33 2
AN27 AN29 WDOVF TM23IOA TM24IOB SCL1 ICR2 ICR6 ICR10 PWM0 PWM3

1 VDD33 VDD33 VREFH P37, P40, P52, P55, P60, LON OSCI OSCO P64, P70, P74, P75 N.C. OCD_SCL P81, VDD33 VDD33 1
AN31 ADTRG TM25IOA TM25IOB ICR0 ICR4 ICR8 ICR12 PWM1
A B C D E F G H J K L M N P R T U V W Y

MAF00026FEM 177
 MN103SD3 Series
Type MN103SD3P MN103SFD3R
Internal ROM type Mask ROM FLASH
ROM (byte) 640K 1024K
RAM (byte) 40K 64K
Package (Lead-free) LQFP100-P-1414
Minimum Instruction 16.7 ns (at 2.7 V to 3.6 V, 60 MHz)
Execution Time

 Interrupts
RESET. IRQ × 8. NMI. Timer × 32. I2C × 3. SIF × 16. DMA × 12. WDT. A/D. Time base timer × 2. System error. Key input. Remote
control × 4

 Timer Counter
8-bit timer A × 10
Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer)
8-bit timer B × 3
Interval timer. Event count. Square-wave output. Simple pulse width measurement. PWM output
16-bit timer × 6
Up-down count. Input capture. PWM output. Compare/capture register 2 channnels
Time base timer × 1
Watchdog timer × 1

 Serial interface
UART/Synchronous/Multi-master I2C interface selective × 3
UART/Synchronous interface selective × 5

 Remote Contorol Interface

Remote control reception: Correspondence with AEHA (Association for Electric Home Appliances) format. Queued reception by low
speed clock

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Serial transmission/reception. A/D conversion finish. I2C transmission/reception. Software.
Remote control data reception
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

 I/O Pins
I/O 81 : Common use
Input 1 : Common use

 A/D converter
10-bit × 8 channels

 ROM Correction
8 channels

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Resolution 10 Bits
Non-linear error ±4 LSB
VDD33 = VREFH = 3.3 V. VSS = 0 V
Differential non-linearity error ±4 LSB

178 MAF00027FEM
 MN103SD3P, MN103SFD3R

 Pin Assignment
LQFP100-P-1414

P42, SBT4, SCL4, IRQ7, NMIRQ

P40, SBI4, TM13IOB, D15

P41, SBO4, SDA4, IRQ6

P87, TM13IOA, D14

P85, TM12IOA, D12

P83, TM11IOA, D10

P86, TM12IOB, D13

P84, TM11IOB, D11

P81, TM10IOA, D8
P82, TM10IOB, D9

P67, KEY7, D1
P66, KEY6, D0
P65, KEY5, A0
P64, KEY4, A1
P75, D7
P74, D6
P73, D5
P72, D4
P71, D3
P70, D2
VDD18

VDD33
VSS
P80

P77
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
P90, SBO0B 76 50 P63, KEY3, A2
P91, SBI0B, SBO5C 77 49 P62, KEY2, A3
P92, SBT0B 78 48 P61, KEY1, A4
P93, SBO3B, SDA3B 79 47 P60, KEY0, A5
P94, SBI3B, SBO6C 80 46 P57, KEY15, A6
P95, SBT3B, SCL3B, SBO7C 81 45 P56, KEY14, A7
PD0, SBO2B, SDA2B 82 44 P55, KEY13, A8
PD1, SBI2B 83 43 P54, KEY12, A9
PD2, SBT2B, SCL2B 84 42 P53, KEY11, A10
PD3, IRQ0B 85 41 P52, KEY10, A11
PD4, IRQ1B 86 40 P51, KEY9, A12
PD5, IRQ2B 87 39 VSS
PD6, IRQ3B, TM15IOA 88 38 P50, KEY8, A13
VDD33 89 37 VDD18
PD7, IRQ4B, TM15IOB 90 36 P35, SBT3A, SCL3A, A14
VSS 91 35 P34, SBI3A, A15
PA0, AN0, SBO7A 92 34 P33, SBO3A, SDA3A, A16
PA1, AN1, SBI7A 93 33 P32, SBT1A, A17
PA2, AN2, SBT7A 94 32 P31, SBI1A, A18
PA3, AN3, TM22IOA 95 31 P30, SBO1A, A19
PA4, AN4, TM21BKA 96 30 P25, IRQ5A, A20
PA5, AN5, TM21GCPA 97 29 P24, IRQ4A, NSC3
PA6, AN6, TM21IOA 98 28 P23, IRQ3A, NSC2
PA7, AN7, TM20IOA 99 27 P22, IRQ2A, NSC1
VREFH 100 26 P21, IRQ1A, RMIN, NSC0
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
P00, SBO0A, NWE0
P01, SBI0A, NWE1
P02, SBT0A, NRE
P03, SBO2A, SDA2A, SBT5A
P04, SBI2A, SBI5A
P05, SBT2A, SCL2A, SBO5A
P06, IRQ5B, TM20IOB
P10, TM4IO, (OCD_SDA)

P12, TM6IO, SYSCLK, TM22IOB

MMOD
OSCO
OSCI
VSS
XI, P07
XO
VDD33
VDD18
NRST
LON
P14, SBT1B, TM14IOA, SBT6A
P15, SBO1B, TM14IOB, SBI6A
P16, SBI1B, TM7IO, SBO6A
OCDMOD
P20, IRQ0A, DK, (VPP)
P11, TM5IO, (OCD_SCL)

MAF00027FEM 179
 MN103SC2 Series
Type MN103SC2A MN103SC2D MN103SFC2D
Internal ROM type Mask ROM FLASH
ROM (byte) 32K 64K
RAM (byte) 4K
Package (Lead-free) QFP044-P-1010F
Minimum Instruction 16.7 ns (4.5 V to 5.5 V)
Execution Time

 Interrupts
8 external interrupts
20 internal interrupts: Watchdog timer. Timer. Serial I/F. PWM. A/D conversion finish. System error

 Timer Counter
8-bit timer × 4
Timer 0 to 3 ...........Interval timer. Event count. Cascading connectable
16-bit timer × 2
Timer 4 ..................Interval timer. Event count. PWM output (6 pins simultaneous output are available). Double buffer
Timer 5 ..................Interval timer. Double buffer. Start synchronized with 3-phase PWM are available
Watchdog timer × 1

 Serial interface
UART (full duplex) /Synchronous interfaces selective × 1
Serial 0...................1-bit to 8-bit transmission (synchronous). 2 and 3 channel type selectable (synchronous)

 I/O Pins
I/O 29 : Common use × 29

 A/D converter
10-bit × 2 unit. Total 8 channels
Simultaneous conversion of 2 series are available. With S/H
Conversion start synchronized with 3-phase PWM or timer 5 are available

 Motor Control PWM

16-bit 3-phase PWM × 1
Minimum resolution: 16.7 ns
Triangular waveform or jigsaw waveform. Dead time setup. Double buffer. Output polar switching is available. PWM output pin protect
function

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Non-linear error 10-bit ±3 LSB
A/D conversion time TAD 1.0 µs
Analog input voltage VIA VSS VDD V
Ta = 25 °C. VDD = 5.0 V. VSS = 0 V

180 MAF00020GEM
MAF00020GEM
QFP044-P-1010F
 Pin Assignment

P37, NPWM02
P36, PWM02
P35, NPWM01
P34, PWM01
P33, NPWM00
P32, PWM00
VDD2
P31, IRQ1
VSS
P30, IRQ0
VDD

44
43
42
41
40
39
38
37
36
35
34

IRQ2, P40 1 33 P27, TM5BIO, TM4O5

IRQ3, P41 2 32 P26, TM5AIO, TM4O4
ADIN0, P50 3 31 P25, TM4BIO, TM4O3
ADIN1, P51 4 30 P24, TM4AIO, TM4O2
ADIN2, P52 5 29 P23, IRQ7, TM3IO, TM4O1
ADIN3, P53 6 28 P22, IRQ6, TM2IO, TM4O0
VSS 7 27 P21, IRQ5, TM1IO
ADIN4, P54 8 26 P20, IRQ4, TM0IO
VDD 9 25 P12, SBI0
ADIN5, P55 10 24 P11, SBT0
ADIN6, P56 11 23 P10, SBO0
12
13
14
15
16
17
18
19
20
21
22

VSS
VDD

OSCI
NRST

OSCO
VDD2
TEST1
TEST2
TEST3

VPPEX

ADIN7, P57
MN103SC2A, MN103SC2D, MN103SFC2D

181
 MN103SC6 Series
Type MN103SFC6K
Internal ROM type FLASH
ROM (byte) 256K
RAM (byte) 40K
Package (Lead-free) QFP100-P-1818B
Minimum Instruction 14.3 ns (3.0 V to 5.5 V)
Execution Time * at internal oscillation used. When instruction RAM executed

 Interrupts
9 external interrupts
45 internal interrupts: Watchdog timer. Timer. Serial I/F. PWM. A/D conversion finish. System error

 Timer Counter
8-bit timer × 12
Timer 0 to 7, 14 to 17 Interval timer. Event count. Cascading connectable
16-bit timer × 6
Timer 8 to 10 .........Interval timer. Event count. PWM output. Double buffer
Timer 11 ................Interval timer. Event count. PWM output (6 pins simultaneous output are available). Double buffer
Timer 12, 13 ..........Interval timer. Double buffer. Start synchronized with 3-phase PWM are available
Watchdog timer × 1

 Serial interface
UART (full duplex) /Synchronous interfaces selective × 3
Serial 0, 1...............7-bit, 8-bit transmission
Serial 2...................1-bit to 8-bit transmission (synchronous). 2 and 3 channel type selectable (synchronous)
Single-master I2C/Synchronous interface selective × 1
Serial 3...................1-bit to 8-bit transmission (synchronous). 2 and 3 channel type selectable (synchronous)

 I/O Pins
I/O 81 : Exclusive × 2. Common use × 79

 A/D converter
10-bit × 3 unit. 20 channels
Simultaneous conversion of 3 series are available
Minimum conversion time: 1.0 µs
Conversion start synchronized with 3-phase PWM or timer 12, 13 are available

 Motor Control PWM

16-bit 3-phase PWM × 2
Minimum resolution: 28.6 ns
Triangular waveform or jigsaw waveform. Dead time setup. Double buffer. Output polar switching is available. PWM output pin protect
function

 Extended Calculation
Multiply and accumulate arithmetic. Multiplication. Saturated arithmetic

 Notes
5 V single power supply (internal regulator)
The power-supply voltage detection can be reset

182 MAF00025EEM
MAF00025EEM
QFP100-P-1818B
 Pin Assignment

P75, TM11O3
P74, TM11O2
P73, TM11IO1
P72, TM11IO0
P65, NPWM11
P64, PWM11

VDD2
VSS
VDD
P67, NPWM12
P66, PWM12
P63, NPWM10
P62, PWM10
P61
P60
P57, NPWM02
P56, PWM02
P55, NPWM01
P54, PWM01
P53, NPWM00
P52, PWM00
P51, TM7IO
P50, TM6IO
P47, TM10BIO
P46, TM10AIO

99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76

100
P76, TM11O4 1 75 P45, TM10BO
P77, TM11O5 2 74 P44, TM10AO
NMI (P80) 3 73 P43, TM9BIO
P81, IRQ01 4 72 P42, TM9AIO
P82, IRQ02 5 71 P41, TM9BO
P83, IRQ03 6 70 P40, TM9AO
P84, TM14IO 7 69 P37, TM8BIO
P85, SBO3 (SDA) 8 68 P36, TM8AIO
P86, SBT3 (SCL) 9 67 VSS
P87, SBI3 10 66 P35, TM5IO
P90, ADIN00 11 65 VDD
P91, ADIN01 12 64 P34, TM4IO
P92, ADIN02 13 63 P33, TM3IO
P93, ADIN03 14 62 P32, TM2IO
VSS 15 61 P31, TM1IO
P94, ADIN04 16 60 P30, TM0IO
VDD 17 59 P27, SBI0
P95, ADIN05 18 58 P26, SBT0
P96, ADIN06 19 57 P25, SBO0
P97, ADIN07 20 56 P24, SBI1
PA0, ADIN08 21 55 P23, SBT1
PA1, ADIN09 22 54 P22, SBO1
PA2, ADIN10 23 53 P21, SBI2
PA3, ADIN11 24 52 P20, SBT2
PA4, ADIN12 25 51 P17, SBO2
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

VSS
VDD

OSCI
NRST

OSCO
VDD2

TEST1
TEST2
TEST3
VDON
VPPEX
P11, IRQ05
P10, IRQ04
P12, IRQ06
P13, IRQ07
P14, IRQ08
P15, TM16IO
P16, TM17IO

PA5, ADIN13
PA6, ADIN14
PA7, ADIN15
PB0, ADIN16
PB1, ADIN17
PB2, ADIN18
PB3, ADIN19
MN103SFC6K

183
 MN103SE3 Series
Type MN103SE3K MN103SFE3K
Internal ROM type Mask ROM FLASH
ROM (byte) 256K
RAM (byte) 8K
Package (Lead-free) QFP100-P-1818B
Minimum Instruction 16.7 ns (4.5 V to 5.5 V)
Execution Time

 Interrupts
9 external interrupts
47 internal interrupts: Watchdog timer. Timer. Serial I/F. PWM. A/D conversion finish. System error

 Timer Counter
8-bit timer × 12
Timer 0 to 7, 14 to 17 Interval timer. Event count. Cascading connectable
16-bit timer × 6
Timer 8 to 10 .........Interval timer. Event count. PWM output. Double buffer
Timer 11 ................Interval timer. Event count. PWM output (6 pins simultaneous output are available). Double buffer
Timer 12, 13 ..........Interval timer. Double buffer. Start synchronized with 3-phase PWM are available
Watchdog timer × 1

 Serial interface
UART (full duplex) /Synchronous interfaces selective × 3
Serial 0, 1...............7-bit, 8-bit transmission
Serial 2...................1-bit to 8-bit transmission (synchronous). 2 and 3 channel type selectable (synchronous)

 I/O Pins
I/O 81 : Common use × 81

 A/D converter
10-bit × 3 unit. 20 channels
Minimum conversion time: 1.0 µs
Simultaneous conversion of 3 series are available
Conversion start synchronized with 3-phase PWM or timer 12, 13 are available

 Motor Control PWM

16-bit 3-phase PWM × 2
Triangular waveform or jigsaw waveform. Dead time setup. Double buffer. Output polar switching is available. PWM output pin protect
function

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Non-linear error 10-bit ±3 LSB
A/D conversion time TAD 1.0 µs
Analog input voltage VIA VSS VDD V
Ta = 25 °C. VDD = 5.0 V. VSS = 0 V

184 MAF00028EEM
 MN103SE3K, MN103SFE3K

 Pin Assignment
QFP100-P-1818B

P44, TM10AO
P45, TM10BO

P42, TM9AIO

P36, TM8AIO
P43, TM9BIO

P37, TM8BIO
P40, TM9AO
P41, TM9BO

P35, TM5IO

P34, TM4IO
P33, TM3IO
P32, TM2IO
P31, TM1IO
P30, TM0IO

P25, SBO0

P22, SBO1

P17, SBO2
P26, SBT0

P23, SBT1

P20, SBT2
P27, SBI0

P24, SBI1

P21, SBI2
VDD
VSS
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
P46, TM10AIO 76 50 P16, TM17IO
P47, TM10BIO 77 49 P15, TM16IO
P50, TM6IO 78 48 NRST
P51, TM7IO 79 47 P14, IRQ08
P52, PWM00 80 46 P13, IRQ07
P53, NPWM00 81 45 P12, IRQ06
P54, PWM01 82 44 P11, IRQ05
P55, NPWM01 83 43 P10, IRQ04
P56, PWM02 84 42 VDD2
P57, NPWM02 85 41 VDD
P60 86 40 VDD
P61 87 39 VPPEX
P62, PWM10 88 38 VSS
P63, NPWM10 89 37 OSCI
P64, PWM11 90 36 OSCO
P65, NPWM11 91 35 PB3, ADIN19
P66, PWM12 92 34 PB2, ADIN18
P67, NPWM12 93 33 TEST3
VDD 94 32 TEST2
P72, TM11IO0 95 31 TEST1
VSS 96 30 PB1, ADIN17
P73, TM11IO1 97 29 PB0, ADIN16
VDD2 98 28 PA7, ADIN15
P74, TM11O2 99 27 PA6, ADIN14
P75, TM11O3 100 26 PA5, ADIN13
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
P80, IRQ00
P81, IRQ01
P82, IRQ02
P83, IRQ03
P84, TM14IO
TCPOUT
P86
P87
P90, ADIN00
P91, ADIN01
P92, ADIN02
P93, ADIN03
VSS
P94, ADIN04
VDD
P95, ADIN05
P96, ADIN06
P97, ADIN07
P76, TM11O4
P77, TM11O5

PA0, ADIN08
PA1, ADIN09
PA2, ADIN10

PA4, ADIN12
PA3, ADIN11

MAF00028EEM 185
 MN103SE4 Series
Type MN103SE4D MN103SE4G MN103SE4K MN103SFE4G MN103SFE4K
Internal ROM type Mask ROM FLASH
ROM (byte) 64K 128K 256K 128K 256K
RAM (byte) 4K 8K 4K 8K
Package (Lead-free) LQFP080-P-1414A
Minimum Instruction 16.7 ns (4.5 V to 5.5 V)
Execution Time

 Interrupts
9 external interrupts
47 internal interrupts: Watchdog timer. Timer. Serial I/F. PWM. A/D conversion finish. System error

 Timer Counter
8-bit timer × 12
Timer 0 to 7, 14 to 17 Interval timer. Event count. Cascading connectable
16-bit timer × 6
Timer 8 to 10 .........Interval timer. Event count. PWM output. Double buffer
Timer 11 ................Interval timer. Event count. PWM output (6 pins simultaneous output are available). Double buffer
Timer 12, 13 ..........Interval timer. Double buffer. Start synchronized with 3-phase PWM are available
Watchdog timer × 1

 Serial interface
UART (full duplex) /Synchronous interfaces selective × 3
Serial 0, 1...............7-bit, 8-bit transmission
Serial 2...................1-bit to 8-bit transmission (synchronous). 2 and 3 channel type selectable (synchronous)

 I/O Pins
I/O 61 : Common use × 61

 A/D converter
10-bit × 3 unit. 16 channels
Minimum conversion time: 1.0 µs
Simultaneous conversion of 3 series are available
Conversion start synchronized with 3-phase PWM or timer 12, 13 are available

 Motor Control PWM

16-bit 3-phase PWM × 2
Triangular waveform or jigsaw waveform. Dead time setup. Double buffer. Output polar switching is available. PWM output pin protect
function

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Non-linear error 10-bit ±3 LSB
A/D conversion time TAD 1.0 µs
Analog input voltage VIA VSS VDD V
Ta = 25 °C. VDD = 5.0 V. VSS = 0 V

186 MAF00029EEM
 MN103SE4D, MN103SE4G, MN103SE4K, MN103SFE4G, MN103SFE4K

 Pin Assignment
LQFP080-P-1414A

P42, TM9AIO

P36, TM8AIO
P43, TM9BIO

P37, TM8BIO

P35, TM5IO

P34, TM4IO
P33, TM3IO
P32, TM2IO
P31, TM1IO

P25, SBO0

P22, SBO1

P17, SBO2
P26, SBT0

P23, SBT1

P20, SBT2
P27, SBI0

P24, SBI1

P21, SBI2
VDD
VSS
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
P46, TM10AIO 61 40 P16, TM17IO
P47, TM10BIO 62 39 NRST
P51, TM7IO 63 38 P14, IRQ08
P52, PWM00 64 37 P13, IRQ07
P53, NPWM00 65 36 P12, IRQ06
P54, PWM01 66 35 P11, IRQ05
P55, NPWM01 67 34 P10, IRQ04
P56, PWM02 68 33 VDD2
P57, NPWM02 69 32 VDD
P62, PWM10 70 31 VDD
P63, NPWM10 71 30 VPPEX
P64, PWM11 72 29 VSS
P65, NPWM11 73 28 OSCI
P66, PWM12 74 27 OSCO
P67, NPWM12 75 26 TEST3
VDD 76 25 TEST2
P72, TM11IO0 77 24 TEST1
VSS 78 23 PA7, ADIN15
P73, TM11IO1 79 22 PA6, ADIN14
VDD2 80 21 PA5, ADIN13
10

12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9
P80, IRQ00
P81, IRQ01
P82, IRQ02
P83, IRQ03
TCPOUT
P90, ADIN00
P91, ADIN01
P92, ADIN02
P93, ADIN03
VSS
P94, ADIN04
VDD
P95, ADIN05
P96, ADIN06
P97, ADIN07
PA0, ADIN08
PA1, ADIN09
PA2, ADIN10

PA4, ADIN12
PA3, ADIN11

MAF00029EEM 187
 MN103SG5 Series
Type MN103SFG5K
Internal ROM type FLASH
ROM (byte) 256K
RAM (byte) 12K
Package (Lead-free) LQFP128-P-1818C
Minimum Instruction 16.7 ns (4.5 V to 5.5 V)
Execution Time

 Interrupts
16 external interrupts
65 internal interrupts: Watchdog timer. Timer. Serial I/F. PWM. A/D conversion finish. System error

 Timer Counter
8-bit timer × 16
Timer 0 to 15 .........Interval timer. Event count. Cascading connectable
16-bit timer × 8
Timer 17, 19, 24 ....Interval timer. Event count. PWM output. Double buffer
Timer 18, 23 ..........Interval timer. Event count. PWM output (6 pins simultaneous output are available). Double buffer
Timer 20 to 22 .......Interval timer. Event count. PWM output. Double buffer. Start synchronized with 3-phase PWM are available

 Serial interface
Multi-master I2C/Synchronous interface selective × 1
Serial 0...................1-bit to 8-bit transmission (synchronous). 2 and 3 channel type selectable (synchronous)
UART (full duplex) /Synchronous interfaces selective × 3
Serial 1...................1-bit to 8-bit transmission (synchronous). 2 and 3 channel type selectable (synchronous)
Serial 2, 3...............7-bit, 8-bit transmission

 I/O Pins
I/O 112 : Common use × 110

 A/D converter
10-bit × 3 unit. 28 channels
Minimum conversion time: 1.0 µs
Simultaneous conversion of 3 series are available
Conversion start synchronized with 3-phase PWM or timer 20, 21, 22 are available

 Motor Control PWM

16-bit 3-phase PWM × 3
Triangular waveform or jigsaw waveform. Dead time setup. Double buffer. Output polar switching is available. PWM output pin protect
function

 Arithmetic unit for inverter system

This series implement the instructions as follows.
High-speed multiplication. High-speed division. Square-root. Absolute value. Trigonometric functions. 2/3 transform. 3/2 transform.
Low-pass filter. PI control

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Non-linear error 10-bit ±3 LSB
A/D conversion time TAD 1.0 µs
Analog input voltage VIA VSS VDD V
Ta = 25 °C. VDD = 5.0 V. VSS = 0 V

188 MAF00032CEM
 MN103SFG5K

 Pin Assignment
LQFP128-P-1818C

P60, TM18AIO, TM18O4

P50, TM16AIO, TM18O2

P61, TM18BIO, TM18O5

P51, TM16BIO, TM18O3

P41, TM7IO, TM18O1

P40, TM6IO, TM18O0
P64, TM19AIO

P54, TM17AIO
P65, TM19BIO

P55, TM17BIO
P66, TM19AO

P62, TM18AO

P56, TM17AO

P52, TM16AO
P67, TM19BO

P63, TM18BO

P57, TM17BO

P53, TM16BO

P46, TM10IO
P47, TM11IO

P45, TM9IO
P44, TM8IO
P43, TM3IO
P42, TM2IO

P33, SBO3

P30, SBO2
P34, SBT3

P31, SBT2
P35, SBI3

P32, SBI2
VDD5

VSS
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
P70, TM20AIO 97 64 SBI1, P25
P71, TM20BIO 98 63 SBT1, P24
P72, TM21AIO 99 62 SBO1, P23
P73, TM21BIO 100 61 SBI0, P22
P74, TM22AIO 101 60 SBT0, P21
P75, TM22BIO 102 59 SBO0, P20
P76 103 58 TM15IO, IRQ07, P07
P77 104 57 TM14IO, IRQ06, P06
P80, PWM00 105 56 TM13IO, IRQ05, P05
P81, NPWM00 106 55 TM12IO, IRQ04, P04
P82, PWM01 107 54 TM5IO, IRQ03, P03
P83, NPWM01 108 53 TM4IO, IRQ02, P02
P84, PWM02 109 52 TM1IO, IRQ01, P01
P85, NPWM02 110 51 TM0IO, IRQ00, P00
P90, PWM10 111 50 NRST
P91, NPWM10 112 49 VPPEX
P92, PWM11 113 48 VDD5
P93, NPWM11 114 47 OSCI
P94, PWM12 115 46 OSCO
P95, NPWM12 116 45 VSS
PB0, TM23O0, TM23AIO 117 44 TEST3
PB1, TM23O1, TM23BIO 118 43 VDD18
PB2, TM23O2, TM24AIO 119 42 SDATA, TEST2
PB3, TM23O3, TM24BIO 120 41 SCLOCK, TEST1
PB4, TM23O4 121 40 ADIN27, PF3
VSS 122 39 ADIN26, PF2
PB5, TM23O5 123 38 ADIN25, PF1
VDD18 124 37 ADIN24, PF0
P10, IRQ08 125 36 ADIN23, PE7
P11, IRQ09 126 35 ADIN22, PE6
P12, IRQ10 127 34 ADIN21, PE5
P13, IRQ11 128 33 ADIN20, PE4
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
11
1
2
3
4
5
6
7
8
9

VDD5
IRQ12, P14
IRQ13, P15
IRQ14, P16
IRQ15, P17

ADIN00, PC0
ADIN01, PC1
ADIN02, PC2
VSS
ADIN03, PC3

ADIN04, PC4
ADIN05, PC5
ADIN06, PC6
ADIN07, PC7
ADIN08, PD0
ADIN09, PD1
ADIN10, PD2

ADIN12, PD4
ADIN13, PD5
ADIN14, PD6
ADIN15, PD7
ADIN16, PE0
ADIN17, PE1
ADIN18, PE2
ADIN19, PE3
ADIN11, PD3
PWM20, PA0
NPWM20, PA1
PWM21, PA2
NPWM21, PA3
PWM22, PA4
NPWM22, PA5

MAF00032CEM 189
 MN103L03 Series
Type MN103LF03R
Internal ROM type FLASH
ROM (byte) 1024K
RAM (byte) 63.5K
LQFP128-P-1818C (Under development), LQFP144-P-2020A (Under development),
Package (Lead-free) QFP100-P-1818B (Under development)
Minimum Instruction 25 ns (at 2.7 V to 3.6 V, 40 MHz)
Execution Time

 Interrupts
RESET. IRQ × 8. NMI. Timer × 27. I2C × 6. SIF × 18. DMA × 12. WDT. A/D. Time base timer × 2. System error. Key input. CAN × 2.
IE × 4

 Timer Counter
8-bit timer × 14
Timer 0, 4 ..............Square-wave output. PWM output. Event count
Timer 1 ..................Square-wave output. Event count
Timer 2 ..................Square-wave output. PWM output. Event count. Serial transfer clock output
Timer 3 ..................Square-wave output. Event count. Serial transfer clock output
Timer 20, 22 ..........Square-wave output. PWM output. Event count. Simple pulse width measurement
Timer 21 ................Square-wave output. Event count. Pulse output for VFD
Timer 6 ..................8-bit freerun timer
Timer A, B, C, D, E .....Serial transfer clock output
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 0, 1, 2 can be cascade-connected
Timer 0, 1, 2, 3 can be cascade-connected
16-bit timer × 6
Timer 7 ..................Square-wave output. High accuracy PWM output (cycle/duty continuous variable). Event count. Input capture
Timer 8 to 12 .........Square-wave output. Event count. Input capture
Time base timer
Watchdog timer × 2

 Serial interface
UART (full duplex) /Synchronous interfaces selective × 6
Multi-master I2C/UART (full duplex) /Synchronous interfaces selective × 3

 IEBus Interface
Number of channels: 2 channels
Communication mode: Selectable from mode 1 or mode 2
Driver and receiver: External

 CAN controller
Number of channels: 2 channels
CAN Protocol Specification Version: CAN2.0B
Transmission speed: Max. 1 Mbps
Data length code: 0 to 8 bytes
Message frame types: Standard and extended frame format supported
Standard (SFF) ID: 11-bit. Extended (EFF) ID: 29-bit
Buffer size (each channel): 32 (transmission/reception)

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Serial transmission/reception. A/D conversion finish. I2C transmission/reception. Time base
timer. Software. IE. CAN
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

190 MAF00033BEM
 MN103LF03R

 I/O Pins
I/O (5 V I/F): 22 (QFP100-P-1818B). 29 (LQFP128-P-1818C). 33 (LQFP144-P-2020A)
(3.3 V I/F): 58 (QFP100-P-1818B). 79 (LQFP128-P-1818C). 89 (LQFP144-P-2020A)
Input (3.3 V I/F): 1 (QFP100-P-1818B). 1 (LQFP128-P-1818C). 1 (LQFP144-P-2020A)

 A/D converter
10-bit × 8 channels (QFP100-P-1818B). 10-bit × 15 channels (LQFP128-P-1818C, LQFP144-P-2020A)

 Pin Assignment
QFP100-P-1818B
P42, SBT4A, SCL4A, IRQ7, NMIRQ

P40, SBI4A, TM11IOB, D15

P41, SBO4A, SDA4A, IRQ6

P85, LED5, TM10IOA, D12

P87, LED7, TM11IOA, D14
P86, LED6, TM10IOB, D13

P83, LED3, TM9IOA, D10

P84, LED4, TM9IOB, D11

P81, LED1, TM8IOA, D8

P82, LED2, TM8IOB, D9

P80, LED0, TM3IO

P67, KEY7, D1
P66, KEY6, D0
P65, KEY5, A0
P64, KEY4, A1
VDD18A

P75, D7
P74, D6
P73, D5
P72, D4
P71, D3
P70, D2
VDD33
VSS
P77
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
P90, SBO0B, CTX0A 76 50 P63, KEY3, A2
P91, SBI0B, CRX0A 77 49 P62, KEY2, A3
P92, SBT0B 78 48 P61, KEY1, A4
P93, SBO3B, SDA3B 79 47 P60, KEY0, A5
P94, SBI3B, ITX0A 80 46 P57, A6
P95, SBT3B, SCL3B, IRX0A 81 45 P56, A7
PD0, SBO2B, SDA2B, SBO8A 82 44 P55, A8
PD1, SBI2B, SBI8A 83 43 P54, A9
PD2, SBT2B, SCL2B, SBT8A 84 42 P53, A10
PD3, IRQ0B, ITX1A 85 41 P52, A11
PD4, IRQ1B, IRX1A 86 40 P51, A12
PD5, IRQ2B, CTX1A 87 39 VSS
PD6, IRQ3B, TM12IOA, CRX1A 88 38 P50, A13
VDD5 89 37 VDD18A(VOUTA)
PD7, IRQ4B, TM12IOB 90 36 P35, SBT3A, SCL3A, A14
VSS 91 35 P34, SBI3A, TM4IO, A15
PA0, AN0, SBO7A 92 34 P33, SBO3A, SDA3A, A16
PA1, AN1, SBI7A 93 33 P32, SBT1A, A17
PA2, AN2, SBT7A 94 32 P31, SBI1A, A18
PA3, AN3, TM22IOA 95 31 P30, SBO1A, A19
PA4, AN4, TM21BKA 96 30 P25, IRQ5A, A20
PA5, AN5, TM21GCPA 97 29 P24, IRQ4A, NCS4
PA6, AN6, TM21IOA 98 28 P23, IRQ3A, NCS3
PA7, AN7, TM20IOA 99 27 P22, IRQ2A, NCS2
VREFH 100 26 P21, IRQ1A, NCS1
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
P00, SBO0A, NWE0
P01, SBI0A, NWE1
P02, SBT0A, NRE
P03, SBO2A, SDA2A, SBO5A
P04, SBI2A, SBI5A
P05, SBT2A, SCL2A, SBT5A
P06, IRQ5B, TM20IOB
P10, TM0IO, (OCD_SDA)

P12, TM2IO, TM22IOB, SYSCLK

MMOD
OSCO
OSCI
VSS
XI, P07
XO
VDD33B
VDD18B(VOUTB)
NRST
LON
P14, SBO1B, TM7IOA, SBO6A, NWDOVF
P15, SBI1B, TM7OB, SBI6A
P16, SBT1B, SBT6A, TM7OC
NOCDMOD
P20, IRQ0A, NDK, (VPP)
P11, TM1IO, (OCD_SCL)

MAF00033BEM 191
 LQFP128-P-1818C

P42, SBT4A, SCL4A, IRQ7, NMIRQ

P40, SBI4A, TM11IOB, D15

P41, SBO4A, SDA4A, IRQ6

P85, LED5, TM10IOA, D12

P87, LED7, TM11IOA, D14
P86, LED6, TM10IOB, D13

P83, LED3, TM9IOA, D10

P84, LED4, TM9IOB, D11

P81, LED1, TM8IOA, D8

P82, LED2, TM8IOB, D9

P80, LED0, TM3IO

P67, KEY7, D1
P66, KEY6, D0
P65, KEY5, A0
P64, KEY4, A1
PE1, CRX0B
PE0, CTX0B
PE6, IRX0B

PE4, IRX1B
PE5, ITX0B

PE3, ITX1B
VDD18A

P75, D7
P74, D6
P73, D5
P72, D4
P71, D3
P70, D2
VDD33
VSS
PE2

P77
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
P90, SBO0B, CTX0A 97 64 PC6
P91, SBI0B, CRX0A 98 63 P63, KEY3, A2
P92, SBT0B 99 62 P62, KEY2, A3
P93, SBO3B, SDA3B 100 61 P61, KEY1, A4
P94, SBI3B, ITX0 101 60 P60, KEY0, A5
P95, SBT3B, SCL3B, IRX0 102 59 P57, A6
PD0, SBO2B, SDA2B, SBO8A 103 58 P56, A7
PD1, SBI2B, SBI8A 104 57 P55, A8
PD2, SBT2B, SCL2B, SBT8A 105 56 P54, A9
PD3, IRQ0B, ITX1A 106 55 P53, A10
PD4, IRQ1B, IRX1A 107 54 P52, A11
PD5, IRQ2B, CTX1A 108 53 P51, A12
PD6, IRQ3B, TM12IOA, CRX1A 109 52 PC5
PF0, AN8, SBO5B 110 51 PC4, CRX1B
PF1, AN9, SBI5B 111 50 PC3, CTX1B
PF2, AN10, SBT5B 112 49 PC2, SBT4B, SCL4B, SBT7B
PF3, AN11, SBO6B 113 48 PC1, SBI4B, SBI7B
PF4, AN12, SBI6B 114 47 PC0, SBO4B, SDA4B, SB07B
PF5, AN13, SBT6B 115 46 VSS
PF6, AN14 116 45 P50, A13
VDD5 117 44 VDD18A(VOUTA)
PD7, IRQ4B, TM12IOB 118 43 P35, SBT3A, SCL3A, A14
VSS 119 42 P34, SBI3A, TM4IO, A15
PA0, AN0, SBO7A 120 41 P33, SBO3A, SDA3A, A16
PA1, AN1, SBI7A 121 40 P32, SBT1A, A17
PA2, AN2, SBT7A 122 39 P31, SBI1A, A18
PA3, AN3, TM22IOA 123 38 P30, SBO1A, A19
PA4, AN4, TM21BKA 124 37 P25, IRQ5A, A20
PA5, AN5, TM21GCPA 125 36 P24, IRQ4A, NCS4
PA6, AN6, TM21IOA 126 35 P23, IRQ3A, NCS3
PA7, AN7, TM20IOA 127 34 P22, IRQ2A, NCS2
VREFH 128 33 P21, IRQ1A, NCS1
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
11
1
2
3
4
5
6
7
8
9
P00, SBO0A, NWE0
P01, SBI0A, NWE1
P02, SBT0A, NRE
P03, SBO2A, SDA2A, SBO5A
P04, SBI2A, SBI5A
P05, SBT2A, SCL2A, SBT5A
P06, IRQ5B, TM20IOB
P10, TM0IO, (OCD_SDA)

P12, TM2IO, TM22IOB, SYSCLK

PB0, TM21GCPB
PB1, TM21BKB
PB2, TM21IOB
PB3, SBO8B
PB4, SBI8B
PB5, SBT8B
NC
MMOD
OSCO
OSCI
VSS
XI, P07
XO
VDD33B
VDD18B(VOUTB)
NRST
LON
P14, SBO1B, TM7IOA, SBO6A, NWDOVF
P15, SBI1B, TM7OB, SBI6A
P16, SBT1B, SBT6A, TM7OC
NOCDMOD
P20, IRQ0A, NDK, (VPP)
P11, TM1IO, (OCD_SCL)

192 MAF00033BEM
 MN103LF03R

LQFP144-P-2020A

P42, SBT4A, SCL4A, IRQ7, NMIRQ

P40, SBI4A, TM11IOB, D15

P41, SBO4A, SDA4A, IRQ6

P85, LED5, TM10IOA, D12

P87, LED7, TM11IOA, D14
P86, LED6, TM10IOB, D13

P83, LED3, TM9IOA, D10

P84, LED4, TM9IOB, D11

P81, LED1, TM8IOA, D8

P82, LED2, TM8IOB, D9

P80, LED0, TM3IO

P67, KEY7, D1
P66, KEY6, D0
P65, KEY5, A0
P64, KEY4, A1
PE1, CRX0B
PE0, CTX0B
PE6, IRX0B

PE4, IRX1B
PE5, ITX0B

PE3, ITX1B
VDD33A

VDD18A

P75, D7
P74, D6
P73, D5
P72, D4
P71, D3
P70, D2
VDD33
VSS
PE7

PE2
P43

P77

P76
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
P90, SBO0B, CTX0A 109 72 PC6
P91, SBI0B, CRX0A 110 71 PG4
P92, SBT0B 111 70 PG3
P93, SBO3B, SDA3B 112 69 P63, KEY3, A2
P94, SBI3B, ITX0A 113 68 P62, KEY2, A3
P95, SBT3B, SCL3B, IRX0A 114 67 P61, KEY1, A4
P96, IRQ0C 115 66 P60, KEY0, A5
P97, IRQ1C 116 65 P57, A6
PD0, SBO2B, SDA2B, SBO8A 117 64 P56, A7
PD1, SBI2B, SBI8A 118 63 P55, A8
PD2, SBT2B, SCL2B, SBT8A 119 62 P54, A9
PD3, IRQ0B, ITX1A 120 61 P53, A10
PD4, IRQ1B, IRX1A 121 60 P52, A11
PD5, IRQ2B, CTX1A 122 59 P51, A12
PD6, IRQ3B, TM12IOA, CRX1A 123 58 PC5
PF0, AN8, SBO5B 124 57 PC4, CRX1B
PF1, AN9, SBI5B 125 56 PC3, CTX1B
PF2, AN10, SBT5B 126 55 PC2, SBT4B, SCL4B, SBT7B
PF3, AN11, SBO6B 127 54 PC1, SBI4B, SBI7B
PF4, AN12, SBI6B 128 53 PC0, SBO4B, SDA4B, SB07B
PF5, AN13, SBT6B 129 52 VSS
PF6, AN14 130 51 P50, A13
VDD5 131 50 VDD18A(VOUTA)
PD7, IRQ4B, TM12IOB 132 49 VDD33A
VSS 133 48 P35, SBT3A, SCL3A, A14
PA0, AN0, SBO7A 134 47 P34, SBI3A, TM4IO, A15
PA1, AN1, SBI7A 135 46 P33, SBO3A, SDA3A, A16
PA2, AN2, SBT7A 136 45 P32, SBT1A, A17
PA3, AN3, TM22IOA 137 44 P31, SBI1A, A18
PA4, AN4, TM21BKA 138 43 P30, SBO1A, A19
PA5, AN5, TM21GCPA 139 42 P25, IRQ5A, A20
PA6, AN6, TM21IOA 140 41 PG2, A21
PA7, AN7, TM20IOA 141 40 P24, IRQ4A, NCS4
VREFH 142 39 P23, IRQ3A, NCS3
PH0, IRQ4C 143 38 P22, IRQ2A, NCS2
PH1, IRQ5C 144 37 P21, IRQ1A, NCS1
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
11
1
2
3
4
5
6
7
8
9
P00, SBO0A, NWE0
P01, SBI0A, NWE1
P02, SBT0A, NRE
P03, SBO2A, SDA2A, SBO5A
P04, SBI2A, SBI5A
P05, SBT2A, SCL2A, SBT5A
P06, IRQ5B, TM20IOB
P10, TM0IO, (OCD_SDA)

P12, TM2IO, TM22IOB, SYSCLK

PB0, TM21GCPB
PB1, TM21BKB
PB2, TM21IOB
PB3, SBO8B
PB4, SBI8B
PB5, SBT8B
PB6
PB7
NC
MMOD
OSCO
OSCI
VSS
XI, P07
XO
VDD33B
VDD18B(VOUTB)
NRST
LON

P15, SBI1B, TM7OB, SBI6A

P16, SBT1B, SBT6A, TM7OC
P14, SBO1B, TM7IOA, SBO6A, NWDOVF

NOCDMOD
P20, IRQ0A, NDK, (VPP)
PG0, IRQ2C
PG1, IRQ3C
P11, TM1IO, (OCD_SCL)

MAF00033BEM 193
 MN103L04 Series
Type MN103LF04R
Internal ROM type FLASH
ROM (byte) 1024K
RAM (byte) 63.5K
Package (Lead-free) LQFP128-P-1818C (Under development), LQFP144-P-2020A (Under development)
Minimum Instruction 25 ns (at 2.7 V to 3.6 V, 40 MHz)
Execution Time

 Interrupts
RESET. IRQ × 8. NMI. Timer × 27. I2C × 6. SIF × 18. DMA × 12. WDT. A/D. Time base timer × 2. System error. Key input. CAN × 2. MLB

 Timer Counter
8-bit timer × 14
Timer 0, 4 ..............Square-wave output. PWM output. Event count
Timer 1 ..................Square-wave output. Event count
Timer 2 ..................Square-wave output. PWM output. Event count. Serial transfer clock output
Timer 3 ..................Square-wave output. Event count. Serial transfer clock output
Timer 20, 22 ..........Square-wave output. PWM output. Event count. Simple pulse width measurement
Timer 21 ................Square-wave output. Event count. Pulse output for VFD
Timer 6 ..................8-bit freerun timer
Timer A, B, C, D, E .....Serial transfer clock output
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 0, 1, 2 can be cascade-connected
Timer 0, 1, 2, 3 can be cascade-connected
16-bit timer × 6
Timer 7 ..................Square-wave output. High accuracy PWM output (cycle/duty continuous variable). Event count. Input capture
Timer 8 to 12 .........Square-wave output. Event count. Input capture
Time base timer
Watchdog timer × 2

 Serial interface
UART (full duplex) /Synchronous interfaces selective × 6
Multi-master I2C/UART (full duplex) /Synchronous interfaces selective × 3

 Audio Output Interface

I2S interface × 7

 Media LB Device Interface

Interface: 3 pin
Transmission rate: 1024Fs or 512Fs
Transmission data: Synchronous. Asynchronous. Control

 CAN controller
Number of channels: 2 channels
CAN Protocol Specification Version: CAN2.0B
Transmission speed: Max. 1 Mbps
Data length code: 0 to 8 bytes
Message frame types: Standard and extended frame format supported
Standard (SFF) ID: 11-bit. Extended (EFF) ID: 29-bit
Buffer size (each channel): 32 (transmission/reception)

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Serial transmission/reception. A/D conversion finish. I2C transmission/reception. Time base timer. Software. CAN
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer
194 MAF00034BEM
 MN103LF04R

 I/O Pins
I/O (3.3 V I/F): 103 (LQFP128-P-1818C). 117 (LQFP144-P-2020A)
Input (3.3 V I/F): 1

 A/D converter
10-bit × 15 channels

 Pin Assignment
LQFP128-P-1818C P42, SBT4A, SCL4A, IRQ7, NMIRQ

P40, SBI4A, TM11IOB, D15

P41, SBO4A, SDA4A, IRQ6

P85, LED5, TM10IOA, D12

P87, LED7, TM11IOA, D14
P86, LED6, TM10IOB, D13

P83, LED3, TM9IOA, D10

P84, LED4, TM9IOB, D11

P81, LED1, TM8IOA, D8

P82, LED2, TM8IOB, D9

P80, LED0, TM3IO

P67, KEY7, D1
P66, KEY6, D0
P65, KEY5, A0
P64, KEY4, A1
PE1, CRX0B
PE0, CTX0B
MLBCLK

MLBDAT
VDD18A

MLBSIG

P75, D7
P74, D6
P73, D5
P72, D4
P71, D3
P70, D2
VDD33

VDD33
VSS

VSS
P77
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
P90, SBO0B, CTX0A 97 64 PC6
P91, SBI0B, CRX0A 98 63 P63, KEY3, A2
P92, SBT0B 99 62 P62, KEY2, A3
P93, SBO3B, SDA3B 100 61 P61, KEY1, A4
P94, SBI3B 101 60 P60, KEY0, A5
P95, SBT3B, SCL3B 102 59 P57, A6
PD0, SBO2B, SDA2B, SBO8A 103 58 P56, A7
PD1, SBI2B, SBI8A 104 57 P55, A8
PD2, SBT2B, SCL2B, SBT8A 105 56 P54, A9
PD3, IRQ0B 106 55 P53, A10
PD4, IRQ1B 107 54 P52, A11
PD5, IRQ2B, CTX1A 108 53 P51, A12
PD6, IRQ3B, TM12IOA, CRX1A 109 52 PC5
PF0, AN8, SBO5B 110 51 PC4, CRX1B
PF1, AN9, SBI5B 111 50 PC3, CTX1B
PF2, AN10, SBT5B 112 49 PC2, SBT4B, SCL4B, SBT7B
PF3, AN11, SBO6B 113 48 PC1, SBI4B, SBI7B
PF4, AN12, SBI6B 114 47 PC0, SBO4B, SDA4B, SB07B
PF5, AN13, SBT6B 115 46 VSS
PF6, AN14 116 45 P50, A13
VDD33 117 44 VDD18A(VOUTA)
PD7, IRQ4B, TM12IOB 118 43 P35, SBT3A, SCL3A, A14
VSS 119 42 P34, SBI3A, TM4IO, A15
PA0, AN0, SBO7A 120 41 P33, SBO3A, SDA3A, A16
PA1, AN1, SBI7A 121 40 P32, SBT1A, A17
PA2, AN2, SBT7A 122 39 P31, SBI1A, A18
PA3, AN3, TM22IOA 123 38 P30, SBO1A, A19
PA4, AN4, TM21BKA 124 37 P25, IRQ5A, A20
PA5, AN5, TM21GCPA 125 36 P24, IRQ4A, NCS4
PA6, AN6, TM21IOA 126 35 P23, IRQ3A, NCS3
PA7, AN7, TM20IOA 127 34 P22, IRQ2A, NCS2
VREFH 128 33 P21, IRQ1A, NCS1
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
11
1
2
3
4
5
6
7
8
9
P00, SBO0A, NWE0
P01, SBI0A, NWE1
P02, SBT0A, NRE
P03, SBO2A, SDA2A, SBO5A
P04, SBI2A, SBI5A

P10, TM0IO, (OCD_SDA)

PB2, TM21IOB, I2S_FSY

PB3, SBO8B, I2S_SCK
P05, SBT2A, SCL2A, SBT5A, I2S_SXR10A, I2S_SXR12A

P12, TM2IO, TM22IOB, SYSCLK

PB0, TM21GCPB, I2S_SXR6
PB1, TM21BKB, I2S_SXR7

PB4, SBI8B, I2S_SXR8

PB5, SBT8B, I2S_SXR9
NMAMODE
MMOD
OSCO
OSCI
VSS
XI, P07
XO
VDD33B
VDD18B(VOUTB)
NRST
LON
P14, SBO1B, TM7IOA, SBO6A, NWDOVF

NOCDMOD
P20, IRQ0A, NDK, (VPP)
P06, IRQ5B, TM20IOB, I2S_SXR11A, I2S_SXR12B

P11, TM1IO, (OCD_SCL)

P15, SBI1B, TM7OB, SBI6A, I2S_SXR10B, I2S_SXR11B

P16, SBT1B, SBT6A, TM7OC, I2S_SXR10C, I2S_SXR11C

MAF00034BEM 195
196
LQFP144-P-2020A

PA5, AN5, TM21GCPA

PA7, AN7, TM20IOA

PA6, AN6, TM21IOA
PA4, AN4, TM21BKA
PA3, AN3, TM22IOA
PA2, AN2, SBT7A
PA1, AN1, SBI7A
PA0, AN0, SBO7A
PF3, AN11, SBO6B

PH1, IRQ5C
PH0, IRQ4C
VREFH
VSS
PD7, IRQ4B, TM12IOB
VDD33
PF6, AN14
PD0, SBO2B, SDA2B, SBO8A

PF5, AN13, SBT6B

PF4, AN12, SBI6B
PF2, AN10, SBT5B
PF1, AN9, SBI5B
PF0, AN8, SBO5B
PD6, IRQ3B, TM12IOA, CRX1A
PD5, IRQ2B, CTX1A
PD4, IRQ1B
PD3, IRQ0B
PD2, SBT2B, SCL2B, SBT8A
PD1, SBI2B, SBI8A
P97, IRQ1C
P96, IRQ0C
P95, SBT3B, SCL3B
P94, SBI3B
P93, SBO3B, SDA3B
P92, SBT0B
P91, SBI0B, CRX0A
P90, SBO0B, CTX0A

111

119
118
117
116
115
114
113
112
110

144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
109
P00, SBO0A, NWE0 1 108 VDD33A
P01, SBI0A, NWE1 2 107 P43
P02, SBT0A, NRE 3 106 VDD18A
P03, SBO2A, SDA2A, SBO5A 4 105 P42, SBT4A, SCL4A, IRQ7, NMIRQ
P04, SBI2A, SBI5A 5 104 P41, SBO4A, SDA4A, IRQ6
P05, SBT2A, SCL2A, SBT5A, I2S_SXR10A, I2S_SXR12A 6 103 P40, SBI4A, TM11IOB, D15
P06, IRQ5B, TM20IOB, I2S_SXR11A, I2S_SXR12B 7 102 P87, LED7, TM11IOA, D14
P10, TM0IO, (OCD_SDA) 8 101 P86, LED6, TM10IOB, D13
P11, TM1IO, (OCD_SCL) 9 100 P85, LED5, TM10IOA, D12
P12, TM2IO, TM22IOB, SYSCLK 10 99 P84, LED4, TM9IOB, D11
PB0, TM21GCPB, I2S_SXR6 11 98 P83, LED3, TM9IOA, D10
PB1, TM21BKB, I2S_SXR7 12 97 P82, LED2, TM8IOB, D9
PB2, TM21IOB, I2S_FSY 13 96 P81, LED1, TM8IOA, D8
PB3, SBO8B, I2S_SCK 14 95 PE7
PB4, SBI8B, I2S_SXR8 15 94 MLBCLK
PB5, SBT8B, I2S_SXR9 16 93 VDD33
I2S_SXR10D, PB6 17 92 MLBSIG
I2S_SXR11D, PB7 18 91 MLBDAT
NMAMODE 19 90 VSS
MMOD 20 89 PE1, CRX0B
OSCO 21 88 PE0, CTX0B
OSCI 22 87 P80, LED0, TM3IO
VSS 23 86 VSS
XI, P07 24 85 P77
XO 25 84 VDD33
VDD33B 26 83 P76
VDD18B(VOUTB) 27 82 P75, D7
NRST 28 81 P74, D6
LON 29 80 P73, D5
P14, SBO1B, TM7IOA, SBO6A, NWDOVF 30 79 P72, D4
P15, SBI1B, TM7OB, SBI6A, I2S_SXR10B, I2S_SXR11B 31 78 P71, D3
P16, SBT1B, SBT6A, TM7OC, I2S_SXR10C, I2S_SXR11C 32 77 P70, D2
NOCDMOD 33 76 P67, KEY7, D1
P20, IRQ0A, NDK, (VPP) 34 75 P66, KEY6, D0
PG0, IRQ2C 35 74 P65, KEY5, A0
PG1, IRQ3C 36 73 P64, KEY4, A1

37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72

PC5
PC6

PG3
PG4

VSS
P54, A9
P55, A8
P56, A7
P57, A6

P52, A11

P50, A13
P51, A12
P53, A10

VDD33A

PG2, A21
PC3, CTX1B
PC4, CRX1B
P60, KEY0, A5
P61, KEY1, A4
P62, KEY2, A3
P63, KEY3, A2

P31, SBI1A, A18

P25, IRQ5A, A20

P32, SBT1A, A17

P30, SBO1A, A19

P21, IRQ1A, NCS1

P22, IRQ2A, NCS2
P23, IRQ3A, NCS3
P24, IRQ4A, NCS4
VDD18A(VOUTA)
PC1, SBI4B, SBI7B

P34, SBI3A, TM4IO, A15

P35, SBT3A, SCL3A, A14

MAF00034BEM
P33, SBO3A, SDA3A, A16
PC2, SBT4B, SCL4B, SBT7B

PC0, SBO4B, SDA4B, SB07B

197
 MN103SA2 Series
Type MN103SFA2R
Internal ROM type FLASH
ROM (byte) 1024K
RAM (byte) 64K
Package (Lead-free) LQFP100-P-1414 (Under development)
Minimum Instruction 16.7 ns (at 2.7 V to 3.6 V, 60 MHz)
Execution Time

 Interrupts
RESET. IRQ × 8. NMI. Timer × 32. I2C × 3. SIF × 16. DMA × 12. WDT. A/D. Time base timer × 2. System error. Key input. Remote
control × 4. CAN × 2

 Timer Counter
8-bit timer A × 10
Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer)
8-bit timer B × 3
Interval timer. Event count. Square-wave output. Simple pulse width measurement. PWM output
16-bit timer × 6
Up-down count. Input capture. PWM output. Compare/capture register 2 channnels
Time base timer × 1
Watchdog timer × 2

 Serial interface
UART/Synchronous/Multi-master I2C interface selective × 3
UART/Synchronous interface selective × 5

 Remote Contorol Interface

Remote control reception: Correspondence with AEHA (Association for Electric Home Appliances) format. Queued reception by low
speed clock

 CAN controller
Number of channels: 2 channels
CAN Protocol Specification Version: CAN2.0B
Transmission speed: Max. 1 Mbps
Data length code: 0 to 8 bytes
Message frame types: Standard and extended frame format supported
Standard (SFF) ID: 11-bit. Extended (EFF) ID: 29-bit
Buffer size (each channel): 32 (transmission/reception)

 DMA controller
Number of channels: 4 channels
Unit of transfer: 8/16/32 bits
Maximum transfer cycles: 65535
Starting factor: External interrupt. Timer. Serial transmission/reception. A/D conversion finish. I2C transmission/reception. Software.
Remote control data reception. CAN
Transfer method: 2-bus cycle transfer
Adressing modes: Fixed. Increment. Decrement
Transfer mode: Word transfer. Burst transfer. Intermittent transfer

 I/O Pins
I/O 22 : (5 V I/O) Common use
59 : (3 V I/O) Common use
Input 1 : (3 V I/O) Common use

 A/D converter
10-bit × 8 channels

 ROM Correction
8 channels

198 MAF00022HEM
 MN103SFA2R

 Electrical Charactreistics (A/D converter characteristics)

Limit
Parameter Symbol Condition Unit
min typ max
Resolution 10 Bits
Non-linear error VDD5 = VREFH = 3.3 V. VSS = 0 V ±4 LSB
Differential non-linearity error VDD5 = VREFH = 5.0 V. VSS = 0 V ±4 LSB

 Pin Assignment
LQFP100-P-1414
P42, SBT4, SCL4, IRQ7, NMIRQ

P40, SBI4, TM13IOB, D15

P41, SBO4, SDA4, IRQ6

P87, TM13IOA, D14

P85, TM12IOA, D12

P83, TM11IOA, D10

P86, TM12IOB, D13

P84, TM11IOB, D11

P81, TM10IOA, D8
P82, TM10IOB, D9

P67, KEY7, D1
P66, KEY6, D0
P65, KEY5, A0
P64, KEY4, A1
P75, D7
P74, D6
P73, D5
P72, D4
P71, D3
P70, D2
VDD18

VDD33
VSS
P80

P77
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
P90, SBO0B, CTX0 76 50 P63, KEY3, A2
P91, SBI0B, CRX0 77 49 P62, KEY2, A3
P92, SBT0B 78 48 P61, KEY1, A4
P93, SBO3B, SDA3B 79 47 P60, KEY0, A5
P94, SBI3B 80 46 P57, KEY15, A6
P95, SBT3B, SCL3B 81 45 P56, KEY14, A7
PD0, SBO2B, SDA2B 82 44 P55, KEY13, A8
PD1, SBI2B 83 43 P54, KEY12, A9
PD2, SBT2B, SCL2B 84 42 P53, KEY11, A10
PD3, IRQ0B 85 41 P52, KEY10, A11
PD4, IRQ1B 86 40 P51, KEY9, A12
PD5, IRQ2B, CTX1 87 39 VSS
PD6, IRQ3B, TM15IOA, CRX1 88 38 P50, KEY8, A13
VDD5 89 37 VDD18
PD7, IRQ4B, TM15IOB 90 36 P35, SBT3A, SCL3A, A14
VSS 91 35 P34, SBI3A, A15
PA0, AN0, SBO7A 92 34 P33, SBO3A, SDA3A, A16
PA1, AN1, SBI7A 93 33 P32, SBT1A, A17
PA2, AN2, SBT7A 94 32 P31, SBI1A, A18
PA3, AN3, TM22IOA 95 31 P30, SBO1A, A19
PA4, AN4 96 30 P25, IRQ5A, A20
PA5, AN5 97 29 P24, IRQ4A, NSC3
PA6, AN6, TM21IOA 98 28 P23, IRQ3A, NSC2
PA7, AN7, TM20IOA 99 27 P22, IRQ2A, NSC1
VREFH 100 26 P21, IRQ1A, RMIN, NSC0
10

12
13
14
15
16
17
18
19
20
21
22
23
24
25
11
1
2
3
4
5
6
7
8
9
P00, SBO0A, NWE0
P01, SBI0A, NWE1
P02, SBT0A, NRE
P03, SBO2A, SDA2A, SBT5A
P04, SBI2A, SBI5A
P05, SBT2A, SCL2A, SBO5A
P06, IRQ5B, TM20IOB
P10, TM4IO, (OCD_SDA)

P12, TM6IO, SYSCLK, TM22IOB

MMOD
OSCO
OSCI
VSS
XI, P07
XO
VDD33
VDD18
NRST
LON
P14, SBT1B, TM14IOA, SBT6A, WDOVF
P15, SBO1B, TM14IOB, SBI6A
P16, SBI1B, TM7IO, SBO6A
OCDMOD
P20, IRQ0A, DK, (VPP)
P11, TM5IO, (OCD_SCL)

Note) VDD5 = VDD33 to 5.5 V. VDD33 = 2.7 V to 3.6 V

MAF00022HEM 199
200
Package Outlines

Package Outlines
QFP Unit : mm

QFP044-P-1010F QFP084-P-1818E QFP100-P-1818B

22.90
12.00 ±0.20 22.90 ±0.20 ±0.20

10.00 ±0.20 18.00 ±0.10 18.00 ±0.10

63 43 75 51

(1.20)
(1.00)
33 23

42 50
34 22 64 76

(1.00)

10.00 ±0.20
12.00 ±0.20

18.00 ±0.10
22.90 ±0.20
18.00 ±0.10
22.90 ±0.20
44 12

1 11
84 22 100 26
(1.00) 0.80 0.35 ±0.05
1.95 ±0.20

1 21 1 25
0.80 (1.20) 0.65 0.30 ±0.05

2.85 max.
(1.00) 0.35 ±0.05

2.45 ±0.20

2.85 max.
24.5 ±0.20
0.10 ±0.10

0.10

0.10 ±0.10
(1.00) 0.15

0.10 ±0.10
(2.45) 0.15
SEATING PLANE (2.45)
0.15 ±0.05

SEATING PLANE
0.15 ±0.05

0.15 ±0.05
SEATING PLANE

0° to 10° 0° to 10°
0° to 10°
0.50 ±0.20 1.30 ±0.20 1.30 ±0.20

LQFP
LQFP048-P2-0707A 9.00 �0.10
LQFP064-P-1414 16.00 ±0.20
LQFP080-P-1414A
16.00 ±0.20
7.00 �0.10
14.00 ±0.10 14.00 ±0.10
36 25 60 41
48 33

40
32 61
37 24 49

(0.825)
(0.75)

(1.00)

14.00 ±0.10

16.00 ±0.20

14.00 ±0.10

16.00 ±0.20
7.00 �0.10
9.00 �0.10

48 13
64 17 80 21

1 12 1 16
1 20
(0.75) 0.50 0.20 �0.05
0.10 M 0.80
(1.00) 0.35 ±0.05
0.16 M (0.825) 0.65 0.30 ±0.05
1.70 max.
1.40 �0.10

0.13 M

1.70 max.
1.40 ±0.10
1.70 max.
1.40 ±0.10
0.10 �0.10

0.10 ±0.10
0.08 (1.00) (1.00)
1.10 ±0.10

0.10
(1.00)
0.10
SEATING PLANE
SEATING PLANE
0.15 ±0.05
0.15 ±0.05
0.15 �0.05

SEATING PLANE

0° to 10° 0° to 10°
0� to 10�
0.50 �0.10 0.50 ±0.20 0.50 ±0.20

LQFP100-P-1414 LQFP100-P-1414A LQFP112-P-2020

16.00 ±0.20 16.00 ±0.20 22.00 ±0.20
14.00 ±0.10 14.00 ±0.10 20.00 ±0.10

75 51 75 51 84 57

50 50 85 56
76 76
(1.00)

(1.00)

(1.225)
14.00 ±0.10
16.00 ±0.20

14.00 ±0.10
16.00 ±0.20

20.00 ±0.10
22.00 ±0.20

100 26 100 26

1 25 1 25 112 29

(1.00) 0.50 0.20 ±0.05 (1.00) 0.50 0.20 ±0.05 1 28

0.10 M 0.10 M
1.70 max.

1.70 max.
1.40 ±0.10

1.40 ±0.10

(1.225) 0.65 0.30 ±0.05

0.13 M
1.70 max.
1.40 ±0.10
0.10 ±0.10

0.10 ±0.10

(1.00) (1.00)
0.10 ±0.10

0.10 0.10
(1.00)
0.10
0.15 ±0.05
0.15 ±0.05

0.15 ±0.05

SEATING PLANE SEATING PLANE

SEATING PLANE

0° to 10° 0° to 10° 0° to 10°

0.50 ±0.20 0.50 ±0.20 0.50 ±0.20

202
 TQFP Unit : mm

LQFP128-P-1818C
20.00 ±0.20
LQFP144-P-2020A TQFP032-P-0707A 9.00 ±0.20
22.00 ±0.20
18.00 ±0.10 7.00 ±0.10
20.00 ±0.10
24 17
96 65
108 73
64
97 16
72
109 25

(1.25)

(1.25)

(0.70)

7.00 ±0.10

9.00 ±0.20
18.00 ±0.10
20.00 ±0.20

20.00 ±0.10
22.00 ±0.20
32 9

128 33 144 37
1 8
(0.70)
1 36
1 32 0.80 0.35 ±0.05
0.50 0.16 M
(1.25) 0.20 ±0.05

1.20 max.
0.50 0.10 M
(1.25) 0.20 ±0.05

1.70 max.
1.40 ±0.10

(1.00)
0.10 M
1.70 max.
1.40 ±0.10

+0.10
0.10 −0.05
0.10 ±0.10
(1.00) 0.10
0.10
0.10 ±0.10

(1.00) (1.00)
0.15 ±0.05

0.10
0.25

0.15 ±0.05

0.15 ±0.05
SEATING PLANE
SEATING PLANE
SEATING PLANE
0° to 10°
0° to 10°
0.50 ±0.20 0° to 8°
0.50 ±0.20
(0.60) 0.50 ±0.10

TQFP048-P-0707B TQFP064-P-1010B TQFP064-P-1010C

9.00 ±0.20 12.00 ±0.20 12.00 ±0.20
7.00 ±0.10 10.00 ±0.10 10.00 ±0.10
36 25 48 33 48 33

49 32 49 32
24
37
(1.25)

(1.25)
(0.75)

10.00 ±0.10
12.00 ±0.20

10.00 ±0.10
12.00 ±0.20
7.00 ±0.10
9.00 ±0.20

64 17 64 17

48 13 1 16 1 16

+0.10
(1.25) 0.50 0.20 −0.05 (1.25) 0.50 0.20 ±0.05
0.10 M
1 12
1.20 max.

1.20 max.
0.50 0.20 ±0.05
0.10 M
(1.00)

(1.00)
1.20 max.

(0.75)
(1.00)

+0.10

+0.10
0.10 −0.05

0.10 −0.05
(1.00) 0.10 (1.00) 0.10
+0.10
0.10 −0.05

(1.00)
0.125 −0.05
+0.10

0.15 ±0.05

0.10 SEATING PLANE SEATING PLANE

0.15 ±0.05

SEATING PLANE

0° to 10° 0° to 8°
0° to 8°
0.50 ±0.10 0.50 ±0.10 0.50 ±0.10

TQFP080-P-1212D
14.00 ±0.20
TQFP128-P-1414A 16.00 ±0.20
TQFP128-P-1414C 16.00 ±0.20
12.00 ±0.10 14.00 ±0.10 14.00 ±0.10

41 96 65 96 65
60

97 64 97 64
61 40
(0.80)

(0.80)
(1.25)
12.00 ±0.10
14.00 ±0.20

14.00 ±0.10
16.00 ±0.20

14.00 ±0.10
16.00 ±0.20

80 21

128 33 128 33
1 20

(1.25) 0.50 0.20 ±0.05 1 32 1 32

0.10 M
(0.80) 0.40 0.16 ±0.05 (0.80) 0.40 0.16 ±0.05
0.08 M 0.08 M
1.20 max.
1.00 ±0.10

1.20 max.

1.20 max.
(1.00)

(1.00)
+0.10
0.10 −0.05

0.10 ±0.10

0.10 ±0.10

0.10
(1.00) 0.10 (1.00) 0.10
(1.00)

SEATING PLANE SEATING PLANE SEATING PLANE

0.15 ±0.05

0.15 ±0.05
0.15 ±0.05

0° to 8° 0° to 8° 0° to 8°

0.50 ±0.10 0.50 ±0.10 0.50 ±0.10

203
QFN SDIP SSOP Unit : mm

QFN044-P-0606A SDIP042-P-0600C SSOP032-P-0300B

6.20±0.10

50
0.
(6.00)

C
3-
33 23
34 22
11.00 ±0.20

6.20±0.10
37.00 ±0.30

(6.00)
(0.63)

(1.00)

42 22
32 17
44 12

0.20 −0.05
+0.10
13.00 ±0.20
1 11
0.80 max

6.10 ±0.20
8.10 ±0.30
R0.30 (0.63)
0.20±0.10

0° to 8°
1 21 (0.50)
1 16

+0.10
0.65 0.30 −0.05

4.30 ±0.30
SEATING PLANE (0.625)

3.30 ±0.20
0.10
0.60±0.10 5.00±0.10
(1.10)
(0

1.50 ±0.20
.1
5)

(1.00)
1 11

3.30 ±0.30
12 1.778 15.24
44 (0.72) 0.50 ±0.10
5.00±0.10

0.10
(1.10)

0.70 ±0.10

0.10 ±0.10
+0.10
1.00 ±0.10 0° to 15° 0.25 −0.05
(0.48)

SEATING PLANE SEATING PLANE SEATING PLANE

34 22

33 23
(0.48)
0.40
0.16±0.06
0.08 M

MBGA MLGA
MBGA255-C-1111A 11.00 �0.15
MLGA100-L-1010
10.20 ±0.08
9.00 max. 4-C0.50
(10.00)
75 51
76 50
10.20 ±0.08
11.00 �0.15
9.00 max.

(10.00)

100 26

1 25
0.85 max.
0.20 ±0.10

TOP VIEW

0.10 S
0.30 �0.10
1.15 �0.20

0.10 SEATING PLANE

0.55 ±0.10 (9.10)
9.75 0.625 �0.2 (7.87)
(1.20)
0.55 ±0.10

� (5.00)
0.625 �0.2

(1.20)

0.65
�0.45 �0.10 (4.35)
�0.15 M 1 25
T 100 26 AREA OF NO RESIN FLASH
R φ2.00
P C (depth 0.07 ±0.02)
0.
N 50
0.16 ±0.06

M
(9.10)
(7.87)
(5.00)
(4.35)

L
K
J
9.75

H
(0.75)

G
(0
.2

F
7)

E
D 76 50
C 75 51 5)
.1
B
0.65 (0.75) (0
A
0.325
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
0.16 ±0.06
BOTTOM VIEW 0.13

UBGA
UBGA036-P-0404AE UBGA257-P-1111A
11.00
4.00 �0.08 �0.10

(3.00)
(3.00)
4.00 �0.08

INDEX AREA
11.00 �0.10
(2.00)

INDEX AREA
0.235 �0.05
1.00 max.

(2.00)

S
0.08 S
SEATING PLANE
0.235 �0.05
1.20 max.

SEATING PLANE
0.08 S

2.50 REF. (0.75) 9.50

(0.75)
B
B

0.50
(0.75)

(0.50)
(0.75)

Y
W
V
U
0.50

T
1 R
P
N
A

2
(0.50)

M
A L
9.50
2.50 REF.

3 K
J
4 H 257� �0.31 �0.05
G �0.05 M S AB
F
5 E
D
6 C
B
A
36-�0.30 �0.05 1 3 5 7 9 11 13 15 17 19
A B C D E F �0.05 M S AB 2 4 6 8 10 12 14 16 18 20

204
Development Support Tools

Development Support Tools

Development Support Tools
Please see the following Web site about information on the development tool.

Information on tool whole

http://www.semicon.panasonic.co.jp/e-micom/support.html
Product support list
http://www.semicon.panasonic.co.jp/e-micom/hardtool/tool_list.html
Inquiry
http://www.semicon.panasonic.co.jp/e-micom/qa.html

AM1 (MN101) Series of 8-bit Microcontroller

Tool Name AM13 (MN101C) Series AM13E (MN101E) Series
ANSI C compiler with extensions for 8-bit microcomputers
Compiler and Assembler
( 8-bit internal computation and bit fields within chars)

Debugger DebugFactory ® Builder

In-circuit emulator supporting real-time debugging with 224 KB ( 944 KB ) of ROM and 16 KB ( 64KB )
Emulator
of RAM, trace function,break functions, etc. ( ):MN101E Series
On-board debugging environment offering real-time debugging using the actual device
Effective solution for field debugging and final product evaluation, including analog characteristics
On-board Debugger
Manufactured by OBJECT Co., Ltd.
Memory reference/modification, breakpoints, etc.

Software Simulator Tool for debugging without the actual machine (DebugFactory ® Builder)

AM3 (MN103) Series of 32-bit Microcontroller

Tool Name AM32 (MN103S) Series AM32L (MN103L) Series

Compiler and Assembler ANSI-compliant C compiler, EC++-compliant compiler

Debugger DebugFactory ® Builder

In-circuit emulator capable of real-time debugging

Emulator Emulation function for 2 MB of on-chip ROM,

Emulation function for 1 MB of on-chip ROM and
64 KB of on-chip RAM, and 1 MB (max. 2 MB)
up to 4 MB of expansion RAM, trace function,
of expansion RAM, trace function, breakpoint
breakpoint functions, etc.
functions, coverage function, etc.
On-board debugging environment offering real-time debugging using the actual device
Effective solution for field debugging and final product evaluation, including analog characteristics
On-board Debugger Memory reference/modification, breakpoints,
Manufactured by OBJECT Co., Ltd.
trace function, etc.
Memory reference/modification, breakpoints, etc.
(depends on device’s on-chip functionality)

Software Simulator Tool for debugging without the actual machine (DebugFactory ® Builder)

Operating Environment
Tool Name Windows® 2000/XP(SP2 or later)/Vista

Compiler and Assembler  *1

DebugFactory ® Builder
Emulator 
Flash Programmer (PX-FW2)
*1: In a command prompt.

206
Business Partner
AM1 (MN101) Series of 8-bit Microcontroller
Tool Name Model Number Description Developer
Set consisting of in-circuit emulator for MN101C series
Uni STAC
In-Circuit Emulator plus Watchpoint debugger for Windows ®. Target probe Sophia Systems Co., Ltd.
MN101C series
selections for emulation is option.
Parallel flash memory Wave Technology Co., Ltd.
Y1100-8 Gang programmer that supports parallel write operations
gang programmer Sales Department (or DEPT)
Yokogawa Digital Computer
Flash on-board MegaNETIMPRESS General-purpose in-circuit programmer for flash
Corporation
serial programmer AF420/AF320 microcomputer
Instruments Business Div.
Flash on-board General-purpose in-circuit programmer for flash
AMOBP OBJECT Co., Ltd.
serial programmer microcomputer
AF9708/09/09C
Flash parallel Parallel (independent write, gang)/Programmer that sup-
AF9723/23B(Gang) Flash Support Group,Inc.
/on-board programmer ports on-board serial write operations
AF9101(On-board)
This CPU evaluation board supports evaluation of AM1
CPU Evaluation Board AM1 STARTER KIT (MN101C/E) applications over a USB connection and in-
cludes both a compiler and a debugger.
On-board debuggibg environment that supports debug-
ging when connected to the AM1 (MN101C/E) microcon- OBJECT Co., Ltd.
On-board Debugging troller in a target system includes a device that already
AM1 Debug Probe
Environment has debugger, compiler, and monitor routines download-
ed and can be connected over a USB connection that
does not require a separate power supply.
The TEF009 Series programming adapter is sold by
Programming Adapter TEF009 Series Flash Support Group, Inc. Which retailer carries the tool Flash Support Group,Inc.
depends on which microcomputer you are using.

AM3 (MN103) Series of 32-bit Microcontroller

Tool Name Model Number Description Developer
GNU Pro C/C++ compiler based on GNU gcc plus simulator/debugger. Red Hat, Inc.
Compiler C/C++ compiler for high-speed and compact embedded
exeGCC Kyoto Microcomputer Co., Ltd.
device development.
High-speed JTAG Emulator that supports the latest de-
PARTNER-Jet for
JTAG Emulator velopment environment embedded RTOS including Linux Kyoto Microcomputer Co., Ltd.
MN103
and Multi-core/SMP.
Parallel flash memory Wave Technology Co., Ltd.
Y1100-8 Gang programmer that supports parallel write operations
gang programmer Sales Department (or DEPT)
Yokogawa Digital Computer
Flash on-board MegaNETIMPRESS General-purpose in-circuit programmer for flash
Corporation
serial programmer AF420/AF320 microcomputer
Instruments Business Div.
Flash on-board
AMOBP In-circuit programmer for flash microcomputer OBJECT Co., Ltd.
serial programmer
AF9708/09/09C
Flash parallel Parallel (independent write, gang)/Programmer that
AF9723/23B(Gang) Flash Support Group,Inc.
/on-board programmer supports on-board serial write operations
AF9101(On-board)
FLS344CSP-103SF33
(CSP 344pin) Conversion adapter for connecting a MN103SF33N flash
Programming Adapter Sunhayato Corp.
FLS360MBGA13-103SF33 microcomputer to a Flash Programmer.
(BGA 360pin)
The TEF009 Series programming adapter is sold by
Programming Adapter TEF009 Series Flash Support Group, Inc. Which retailer carries the tool Flash Support Group,Inc.
depends on which microcomputer you are using.
This CPU evaluation board supports evaluation of AM3
CPU Evaluation Board AM3 STARTER KIT (MN103SFA5K) applications over a USB connection and
includes both a compiler and a debugger.
On-board debugging environment of fering debug- OBJECT Co., Ltd.
ging functionality through a connection with an AM32L
On-board Debugging
AM32L Debug Probe (MN103L) microcomputer target system. Uses a USB
Environment
connection that can also power the device and includes a
debugger and compiler.

207
Package - Surface Mount Socket
Package code Panasonic number Remarks Distributor

QFP044-P-1010 PRB-SKT44QF10

QFP084-P-1818 PRB-SKT84QF18 Panasonic Corporaion

QFP100-P-1818 PRB-SKT100QF18 Plastic package exclusive use

Package code Panasonic number Socket manufacturer catalog number Distributor

TQFP032-P-0707 — HQPACK032SA NQPACK032SA

SSOP032-P-0300 — HSPACK32BK NSPACK32BK

QFP044-P-1010F PRB-TET44QF10F*1 HQPACK044SA NQPACK044SA

PRB-TET48TH07 HQPACK048SD NQPACK048SD

QFH048-P-0707
TQFP048-P-0707B
PRB-TET48TH07-SL HQPACK048SD NQPACK048SD-SL

PRB-TET64TH10 HQPACK064SD NQPACK064SD

QFH064-P-1010
PRB-TET64TH10-SL HQPACK064SD NQPACK064SD-SL

PRB-TET64LF14 HQPACK064SA160 NQPACK064SA160

LQFP064-P-1414
PRB-TET64LF14-SL HQPACK064SA160 NQPACK064SA160-SL

PRB-TET80TH12 HQPACK080SD NQPACK080SD-ND

QFH080-P-1212
TQFP080-P-1212
PRB-TET80TH12-SL HQPACK080SD NQPACK080SD-ND-SL

PRB-TET80LF14 HQPACK080SB160 NQPACK080SB

LQFP080-P-1414 Tokyo Eletech Corporation
PRB-TET80LF14-SL HQPACK080SB160 NQPACK080SB-SL
It is possible to order by the
PRB-TET100LF14 HQPACK100SD NQPACK100SD-ND
LQFP100-P-1414 Panasonic number.
PRB-TET100LF14-SL HQPACK100SD NQPACK100SD-ND-SL

PRB-TET100QF18 HQPACK100SB NQPACK100SB

QFP100-P-1818
PRB-TET100QF18-SL HQPACK100SB NQPACK100SB-SL

PRB-TET112LF20 HQPACK112SB NQPACK112SB

LQFP112-P-2020
PRB-TET112LF20-SL HQPACK112SB NQPACK112SB-SL

PRB-TET128LF14 HQPACK128SE NQPACK128SE

TQFP128-P-1414
PRB-TET128LF14-SL HQPACK128SE NQPACK128SE-SL

PRB-TET128LF18 HQPACK128SD NQPACK128SD

LQFP128-P-1818
PRB-TET128LF18-SL HQPACK128SD NQPACK128SD-SL

PRB-TET160QF28 HQPACK160SB NQPACK160SB

QFP160-P-2828
PRB-TET160QF28-SL HQPACK160SB NQPACK160SB-SL

QFP208-P-2828 PRB-TET208QF28H HQPACK208SD306H NQPACK208SD

*1 : Lead-free package
-SL : Screw reinforcement from solder fixation + back of substrate

208
Business Partner Contacts
Region Business Partner Tel/Fax URL/E-mail

Yokogawa Digital Computer Corporation

Tel: +1-800-888-6400
Yokogawa Corporation of America URL: http://www.yokogawa-digital.com/en/
U.S.A 2 Dart Road Newnan, Georgia 30265 USA
+1-770-253-7000
E-mail: [email protected]
Fax: +1-770-251-6427
Hitex Development Tools GmbH Tel: +49-721-9628-0 URL: http://www.hitex.de/
Germany Greschbachstr. 12, 76229 Karlsruhe, Germany Fax: +49-721-9628-149 E-mail: [email protected]
Ashling Microsystems Limited Tel: +33-1-43-41-06-37 URL: http://www.ashling.com
UK, France 11 avenue Charles de Gaulle 95700 Roissy en France Fax: +353-61-334477 E-mail: [email protected]
Yokogawa Measuring Instruments Korea Corp. (YIK)
Tel: +82-2-551-0660
Korea City Air Terminal Bldg., 405-9, #159-6, Samsung-dong, Kangnam-ku, Seoul,
Fax: +82-2-551-0665
URL: http://www.yokogawa-yik.co.kr/
135-728, Korea
Tel: +86-21-6239-6363
Fax: +86-21-6880-4987
• Beijing Office
Tel: +86-10-85221699
Yokogawa Shanghai Trading Co., Ltd. Fax: +86-10-85221677
China 3F Tower D Cartelo Crocodile Building, No.568 Tianshan W Road, Shanghai, • Guangzhou Office URL: http://www.yokogawa.com/cn-ysh/
200335 China. Tel: +86-20-28849908
Fax: +86-20-28849937
• Shenzhen Office
Tel: +86-755-8373-4456
Fax: +86-755-8373-4457
Yokogawa India Ltd Tel: +91-80-4158-6000
India 96, Hosur Road, Electronics City, Bangalore - 560 100 India Fax: +91-80-2852-0625
URL: http://www.yokogawa.com/in/

Yokogawa Engineering Asia Pte. Ltd. Tel: +65-6241-9933 URL: http://www.yokogawa.com/sg/

Other Asia 5 Bedok South Road, Singapore 469270, Singapore Fax: +65-6241-2606 E-mail: [email protected]
Yokogawa Digital Computer Corporation
Japan, Tel: +81-42-333-6222 URL: http://www.yokogawa-digital.com/en/
3rd floor, Keio-Fuchu 1-Chome Building 1-9 Fuchucho, Fuchu-shi, Tokyo,
Other countries 183-8516, Japan
Fax: +81-42-352-6107 E-mail: [email protected]

Sophia Systems Co.,Ltd.

Emdoor Electronic & Technology Co., Ltd.
China & Tel: +86-755-83474893 URL: http://www.emdoor.com
Room 506#, China Non-ferrous Metal Building 6013# Shennan Road Futian
Hong Kong District Shenzhen China
Fax: +86-755-83474895 E-mail: [email protected]

Flash Technology Tel: +65-6749-6168 URL: http://www.flashtech.com.sg

Singapore No.61 Kaki Bukit Avenue 1 #04-15, Shun Li Industrial Park Singapore 417943 Fax: +65 6749-6138 E-mail: flashsgp@pacific.net.sg
SuperLink Tel: +886-2-2698-34-56 URL: http://www.superlink.com.tw
Taiwan 3F-8, 77 Shin-Tai-Wu Road Sec. 1, Shi-Shih Taipei Hsien Taiwan 221 Fax: +886-2-2698-35-35 E-mail: [email protected]
Trident Infosol Pvt. Ltd.
Tel: +91-80-2224-5037 URL: http://www.tridentinfosol.com
#3, 2nd Cross, Raja Ram Mohan Roy Extn., Off K.H. Road (Double Road)
Fax: +91-80-2229-1566 E-mail: [email protected]
India Bangalore India 560 027
Steffi Smile Agency Tel: +91-80-642-0999
E-mail: [email protected]
68, 14th Main, Muneshwara block, G.E.F. Post, Bangalore 560 026 India Fax: +91-80-642-2555
Sophia Systems USA Tel: +1-888-423-2305 URL: http://www.sophiasys.com
North America 422 Peninsula Avenue San Mateo CA U.S.A 94401 Fax: +1-650-375-8666 E-mail: [email protected]
France, Antycip Tel: +33-1-39 61 14 14 URL: http://www.antycip.fr
Germany, Italy 98 ter, Boulevard Hellos Boite, Postale 111-F Argenteuil Cedex France 95103 Fax: +33-1-30 76 29 73 E-mail: [email protected]
Direct Insight Tel: +44-1280-700262 URL: http://www.directinsight.co.uk
UK St. James Road Brackley Northants England NN137XY Fax: +44-1280-700577 E-mail: [email protected]
Eastern Trade Tel: +49-8261 7374 14 URL: http://www.eastern-trade.com
Europe Georgenstr. 46 a 87719 Mindelheim Germany Fax: +49-8261 7372 62 E-mail: [email protected]
Sightsys Tel: +972-3-922-2771 URL: http://www.sightsys.co.il
Israel 7 Imbar St., Kiriat Arie Petah-Tikva Israel 49511 Fax:+972-3-922-2059 E-mail: [email protected]
Japan Sophia Systems Co., Ltd. Tel: +81-44-989-7110 URL: http://www.sophia-systems.com
South Korea 6-2 Minami-Kurokawa, Asao-ku, Kawasaki-shi, Kanagawa, 215-8588 Japan Fax: +81-44-989-7014 E-mail: [email protected]

Red Hat, Inc.

Tel: +1-919-754-3700
U.S.A. 1801 Varsity Drive Raleigh, NC 27606 U.S.A.
Fax: +1-919-754-3701
URL: http://www.redhat.com/

Red Hat K.K. Tel: +81-3-5798-8500 URL: http://www.jp.redhat.com/

Japan Ebisu Neonate Bldg. 8F 4-1-18 Ebisu, Shibuya-ku Tokyo 150-0013 Japan Fax: +81-3-5798-8599 E-mail: [email protected]

Kyoto Microcomputer Co., Ltd.

Tel: +81-75-335-1050 URL: http://www.kmckk.co.jp/eng/
Japan 2-44 Ooenakayama-cho, Nishikyo-ku, Kyoto-city, Kyoto 610-1104 Japan
Fax: +81-75-335-1051 E-mail: [email protected]

Communication and Technology Systems, Inc. [C.A.T.S.,INC.]

Tel: +1-408-971-6253 URL: http://www.zipc.com/
U.S.A. 111N. Market Street, Suite 1000-17 San Jose, CA 95113-1101, U.S.A.
Fax: +1-408-288-4633 E-mail: [email protected]

Sunhayato Corp.
Tel: +81-3-3984-7791 URL: http://www.sunhayato.co.jp/
Japan 3-40-1 Minamiootsuka Toshima-ku,Tokyo 170-0005 Japan
Fax: +81-3-3971-0535 E-mail: [email protected]

209
Wave Technology Co.,Ltd.
Hatagaya New Center building 6F, Tel: +81-3-5304-1885 URL: http://www.wavetechnology.co.jp
Japan
2-7-2 Hatagaya, Shibuya-ku Tokyo, 151-0072 Japan Fax: +81-3-5304-1886 E-mail: [email protected]

OBJECT Co.,Ltd.
3rd Floor, Mori New Bldg. Tel: +81-6-6844-1747 URL: http://www.object.co.jp/
Japan
1-3-1 Hotarugaike Higashimachi, Toyonaka, Osaka 560-0032, Japan Fax: +81-6-6844-1760 E-mail: [email protected]

Tokyo Eletech Corporation

Tel: +81-3-5295-1661 http://www.tetc.co.jp/e_index.htm
Japan 3-10 Akihabara, Taito-ku, Tokyo 110-0006 Japan
Fax: +81-3-5295-1775 E-mail: [email protected]

Flash Support Group, Inc.

USA•Canada TOA Electric USA, Inc Tel: +1-859-881-3330 URL: http://www.toa-electric.com/
Mexico 100 Capital Court, Nicholasville, Kentucky, 40356, USA Fax: +1-859-881-3336 E-mail: [email protected]
Sanshin Electronics Corporation Tel: +1-949-727-4435 URL: http://www.sanshinusa.com/
12-D Mauchly, Irvine, California, 92618, U.S.A. Fax: +1-949-727-4402 E-mail: [email protected]
USA Nihon Denkei Co., Ltd. Los-angeles Report Place Tel: +1-310-5339502
c/o PCE International, Inc. 20695 S. Western Ave., Suite 209 Torrance, CA E-mail: [email protected]
Fax: +1-310-3205793
90501-1831, USA
Nihon Denkei Co., Ltd Singapore Branch Tel: +65-6355-0851 URL: http://www.n-denkei.com/
Singapore 50 Bukit Batok St 23, #05-26 Midview Building, Singapore, 659578 Fax: +65-6355-0751 E-mail: [email protected]
Nihon Denkei (Malaysia) Sdn Bhd Tel: +60-3-9287-8671 URL: http://www.n-denkei.com/
No.73 & No.75 Jalan 3/76D, Desa Pandan, Kuala Lumpur, 55100, Malaysia Fax: +60-3-9287-8670 E-mail: [email protected]
Malaysia
Nihon Denkei (Malaysia) Sdn Bhd (Penang Office) Tel: +60-4-646-5895 URL: http://www.n-denkei.com
B-4-8, Krystal Point, 303 Jalan Sultanazlan Shah, 11900 Fax: +60-4-646-4895 E-mail: [email protected]
Nihon Denkei (Thailand) Co., Ltd. (Bangkok Office) Tel: +66-2-675-5688 URL: http://www.n-denkei.com/
Rm. No.232-3, 23rd Floor, 889 Thai CC Tower, South Sathorn Rd, Sathorn
Fax: +66-2-675-5692 E-mail: [email protected]
Bangkok, 10120, Thailand
Nihon Denkei (Thailand) Co., Ltd. (Laem Chabang Office) Tel: +66-38-495-186 URL: http://www.n-denkei.com/
Thailand 53 Moo 9, Rm. No.1004, 10th Floor, Talaythong Tower, T.TungSukhla,
Fax: +66-38-492-725 E-mail: [email protected]
A.Sriracha, Chonburi, 20230, Thailand
Nihon Denkei (Thailand) Co., Ltd. (Chiangmai Office) Tel: +66-53-203-452 URL: http://www.n-denkei.com/
Unit 127, 2nd Floor Airport Business Park Building, 90 Mahidol Rd., A.Muang
Fax: +66-53-203-452 E-mail: [email protected]
Chiangmai, 50100, Thailand
Nihon Denkei Co., Ltd. Vietnam (Hanoi) Branch Tel: +84-4-951-6505 URL: http://www.n-denkei.com/
Room No.206, Techno Center, Thang Long Industrial Park, Dong Anh Dist,
Fax: +84-4-951-6508 E-mail: [email protected]
Hanoi, Vietnam
Vietnam
Nihon Denkei Co., Ltd. Vietnam (Ho Chi Minh City) Branch Tel: +84-8-2646363 to 4
Unit 310, Hoang Anh Gia Lai Building, 7/1 Thanh Thai St, Dist 10, HCMC, E-mail: [email protected]
Fax: +84-8-2646365
Vietnam
Tel: +886-2-8990-2119
Programming Technology Co., Ltd URL: http://www.programtek.com.tw/
Fax: +886-2-8890-2116
Taiwan
Nihon Denkei Co., Ltd. Taiwan (Taipei) Branch Tel: +886-2-55511991 URL: http://www.n-denkei.com.tw
5F, No.415, Rueiguang RD., Neihu District. TAIPEI City 114, Taiwan. Fax: +886-2-55511990 E-mail: [email protected]
ND Korea Co., Ltd. (Suwon Office) Tel: +82-31-202-4491 URL: http://www.ndkorea.co.kr/
Digital Empire C-1301, 980-3 Youngtong-Dong, Youngtong-Gu, Suwon-Si,
Fax: +82-31-202-4459 E-mail: [email protected]
Gyeonggi-Do, 443-812, Korea
Korea ND Korea Co., Ltd.(Busan Office)
Tel: +82-51-332-4491 URL: http://www.ndkorea.co.kr/
616-801 Sungwon Mentoro B/D 1009, 177-27 Guseo-dong, Geumjeong-gu,
Fax: +82-51-332-4501 E-mail: [email protected]
Busan Metropolitan City, Korea
Nihon Denkei Co., Ltd. Shanghai Branch Tel: +86-21-5820-5887
E-mail: [email protected]
RM. Shanghai Zizhu Science-based Industrial Park, 609, ZIRI Road, Shanghai, China Fax: +86-21-5820-4861
Nihon Denkei Co., Ltd. Shanghai Putong Office Tel: +86-21-5820-9710
E-mail: [email protected]
Rm. 1709, Yu-an B/D, No.738 Dongfang Road, Shanghai, China Fax: +86-21-5820-1403
Nihon Denkei Co., Ltd. Shanghai Putong Office Tel: +86-21-58205887
E-mail: [email protected]
RM. Shanghai Zizhu Science-based Industrial Park, 609, ZIRI Road, Shanghai, China Fax: +86-21-34293306
Nihon Denkei Co., Ltd. Dalian Branch Office Tel: +86-411-87622136
Rm. 1105 GuGeng international building No.81 Hong Mei District ECONOMIC E-mail: [email protected]
Fax: +86-411-87625794
& TECHNICAL DEVELOPMEN P.R. China
Nihon Denkei Co., Ltd. Shenzhen Branch Office Tel: +86-755-82096179
E-mail: [email protected]
Rm 3113, News Bldg, No.2 Shennan Middle Road, Shenzhen, China Fax: +86-755-82096170
Nihon Denkei Co., Ltd. Zhuhai Report Place Tel: +86-756-2289530
Rm 701, Bld20, Yue Hai International Garden, Gong Bei District, Zhuhai, E-mail: [email protected]
Fax: +86-756-2299140
GuangDong, China
Nihon Denkei Co., Ltd. Tianjin Branch Office Tel: +86-22-83865887
China Rm 9-D, Pingan Mansion, No.59 Machang Road, Hexi District, Tianjin, China
E-mail: [email protected]
Fax: +86-22-23282110
Nihon Denkei Co., Ltd. Wuxi Branch Office Tel: +86-510-85222122
E-mail: [email protected]
Rm 908, Baishida building, No.6 North Changjiang Road, Wuxi, Jiangsu, China Fax: +86-510-85222386
Nihon Denkei Co., Ltd. Beijing Branch Office Tel: +86-10-51311181
E-mail: [email protected]
Rm 05, 6 Floor, No.5 Second Alley Xiangjunnanli Chaoyang Districtbeijing, China Fax: +86-10-51311200
Nihon Denkei Co., Ltd. Guangzhou Branch Office Tel: +86-20-38248428
Rm 3108, East Tower, Yang Cheng Internation Commercial Center B/D E-mail: [email protected]
Fax: +86-20-38248468
No.122, Ti Yu Dong Road. Tianhe District Guangzhou, China
Nihon Denkei Co., Ltd. Suzhou Branch Office Tel: +86-512-68785930
E-mail: [email protected]
Rm 16-A Kingstower, No.1156 Binheroad, Suzhou China Fax: +86-512-68785310
Nihon Denkei Co., Ltd. Hangzhou Branch Office Tel: +86-571-85803963
E-mail: [email protected]
Rm. 308, Zhejin Square, No.78 Fengqi RD, Hangzhou, China Fax: +86-571-85809325
Nihon Denkei Co., Ltd. Xiamen Branch Office Tel: +86-592-5529642
Room D2, 8/F, Post Building, No.458 Xianyue Road, Siming District, Xiamen, E-mail: [email protected]
Fax: +86-592-5529742
Fujian, China

210
 Nihon Denkei Co., Ltd. Qingdao Branch Office Tel: +86-532-85870213
A Room 19F Mongkok Building No.73, HongKong Zhong Road Qingdao E-mail: [email protected]
Fax: +86-532-85875991
Shandong China. pc:266071
Nihon Denkei Co., Ltd. Changchun Branch Office Tel: +86-431-82908215
Room 1505 No.498 Shengli Street Wutai Business Centre Kuancheng Districy E-mail: [email protected]
Fax: +86-431-82908225
Changchun City Jilin Province
China Tel: +86-21-5405-0303
Yokogawa Shanghai Trading Co., Ltd Fax: +86-21-6880-4987, URL:http://www.yokogawa.com/cn-ysh/cp/
K. Wah Centre 28, 29F 1010 Hui Hai Zhong Road Shanghai, 200031, China 6880-9254, aboutus/ysh/ysh_service-cn.htm
6880-3005
Tel: +86-512-6808-7869
Programming (Suzhou) Electronics Technology Co., Ltd URL: http://www.programtek.com.cn/
Fax: +86-512-6808-7269
Nihon Denkei (Hong Kong) Limited Tel: +852-8306-0866 URL: http://www.n-denkei.com/
Hong Kong Room 301, 3F, Sun Hong Kai Centre, 30 Harbour Road, Wan Chai, Hong Kong Fax: +852-8306-0869 E-mail: [email protected]
Nihon Denkei (India) Sdn Bhd Tel: +91-124-4715777 URL: http://www.n-denkei.com/
India Unit No.502, 5th Floor, Millennium Plaza, B-Block, Sushant Lok-1, Gurgaon
Fax: +91-124-4715700 E-mail: [email protected]
122016, India
Nihon Denkei Co., Ltd. Philippines Manila Resident Office Tel: +63-2-8452638
Philippines Unit 1002 Rufino Bldg Ayala Ave Cor. Herrera St Makati City 1200 Philippines
E-mail: [email protected]
Fax: +63-2-8454206
Nihon Denkei Co., Ltd. Indonesia Jakarta Resident Office Tel: +62-21-8564857
Indonesia Wisma Indomobile 2 Lantai 4, Jl. MT. haryono Kav 9, Jakarta Timur 13330, E-mail: [email protected]
Fax: +62-21-8570571
Indonesia

Ablty Co., Ltd.

Tel: +81-6-6901-2267 URL: http://www.ablty.jp
Japan 1-4-13 Kajimachi Moriguchi-city Osaka 570-0015 Japan
Fax: +81-6-6901-5118 E-mail: [email protected]
Shen Zhen Ablty Business Leader Co., Ltd.
Tel: +86-755-8376-9356
China Rm #2306 Plot 2 WeiPeng Garden Zhenzhong RD Futian District Shenzhen-
Fax: +86-755-8376-9354
city Guangdong, China

Rental Company Contact Information

Region Rental Company Tel/Fax URL/E-mail

Orix Rentec Corporation

Tel: +81-3-3473-7561
Japan 5-7-21 Kitashinagawa Shinagawa-ku, Tokyo 141-8681 Japan
Fax: +81-3-3473-7549
URL: http://www.orixrentec.jp/

211
212
 Microcomputer Home Page
http://panasonic.net/sc/en/e-micom

 Hardware Manual and Development Tool Manual Download

http://panasonic.net/sc/en/e-micom/manual

 Inqury of Technical Support

http://panasonic.net/sc/en/e-micom/inquiry

Pub. No.A000122E

Microcomputer
AM Series Selection Guide

March 2, 2009 29th Edition

Issued by

© Panasonic Corporation 2009

 SALES OFFICES
NORTH AMERICA  Thailand Sales Office:
Panasonic Industrial (Thailand) Ltd. [PICT]
 U.S.A. Sales Office:
252-133 Muang Thai-Phatra Complex Building, 31st Floor,
Panasonic Industrial Company [PIC]
Rachadaphisek Road, Huaykwang, Bangkok 10320, Thailand
 San Diego Office:
Tel:66-2-693-3400 to 3421 Fax:66-2-693-3422 to 3427
4995 Murphy Canyon Rd., Suite 105, San Diego, CA 92123,
 Philippines Sales Office:
U.S.A.
Panasonic Industrial Asia Pte. Ltd. Philippine Branch [PIAP]
Tel:1-858-503-2965
102 Laguna Blvd., Laguna Technopark Inc., Barrio Don Jose, Sta.
 New Jersey Office:
Rosa, Laguna 4026, the Philippines
3 Panasonic Way Secaucus, NJ 07094, U.S.A.
Tel:63-2-520-3153/8126 Fax:63-2-520-8629
 Chicago Office:
 China Sales Office:
5201 Tollview Drive, Rolling Meadows, IL 60008, U.S.A.
Panasonic Semiconductor Sales (China) [PSCSCN]
 San Jose Office:
 Beijing Sales Office:
2033 Gateway Place, Suite 200, San Jose, California 95110,
Panasonic Corporation of China
U.S.A
8th Floor, Tower C, Heqiao Buiding, No.8A Guanghua Road,
 Canada Sales Office:
Chaoyang District, Beijing, China, 100026
Panasonic Canada Inc. [PCI]
Tel:86-10-6566-3706 Fax:86-10-6566-3704
5770 Ambler Drive 27 Mississauga, Ontario L4W 2T3, Canada
 Tianjin Sales Office:
Tel:1-905-238-2315 Fax:1-905-238-4012
Panasonic Industrial (China) Co., Ltd. Tianjin Branch
Room No.1001, Tianjin International Building, 75, Nanjing Road,
LATIN AMERICA Heping District, Tianjin, China, 300050
 Mexico Sales Office: Tel:86-22-2313-9771 to 9774 Fax:86-22-2313-9770
Panasonic de Mexico, S.A. de C.V. [PANAMEX]  Dalian Sales Office:
Amores 1120 Col. Del Valle Delegacion Benito Juarez C.P. 03100 Panasonic Corporation of China Dalian Branch
Mexico, D.F. Mexico 9th Floor, Xiwang Tower, No.136 Zhongshan Road,
Tel:52-5-488-1000 Fax:52-5-488-1073 Zhongshan District, Dalian, China, 116011
 Guadalajara Office: Tel:86-411-8370-8805 to 8807 Fax:86-411-8368-6802
Sucursal Guadarajara Av. Lazaro Cardenas 2305 Local G-102  Shanghai Sales Office:
Plaza Comercial Abastos; Col. Las Torres Guadalajara, Jal. Panasonic Industrial (China) Co., Ltd.
44920, Mexico Semiconductor Group
Tel:52-3-671-1205 Fax:52-3-671-1256 12th Floor, China Insurance Building, 166 East Road
 Brazil Sales Office: Lujiazui, Pudong New District, Shanghai 200120, China
Panasonic do Brasil Ltda. [PANABRAS] Tel:86-21-3855-2000 Fax:86-21-3855-2378
Caixa Postal 1641, Sao Jose dos Campos, Estado de Sao Paulo,  Shenzhen Sales Office:
Brasil Panasonic SH Industrial Sales (Shenzhen) Co., Ltd.
Tel:55-12-3935-9000 Fax:55-12-3931-3789 Semiconductor Group
Futian Branch: 6th Floor, Excellence Times Square,
EUROPE 4068 Yitian Road, Futian District, Shenzhen 518048, China
Tel:86-755-8255-8888 Fax:86-755-8255-8828
 Europe Sales Office:
 Hong Kong Sales Office:
Panasonic Industrial Europe GmbH [PIE]
Panasonic Semiconductor Sales (China) [PSCSCN]
 Germany Sales Office:
 Panasonic Shun Hing Industrial Sales (Hong Kong) Co., Ltd.
Hans-Pinsel-Strasse 2 85540 Haar, Germany
Semiconductor Group
Tel:49-89-46159-119 Fax:49-89-46159-195
33rd Floor, Office Tower, Langham Place, 8 Argyle Street,
Mongkok, Kowloon, Hong Kong
ASIA Tel:852-2529-7322 Fax:852-2865-4455
 Singapore Sales Office:  Taiwan Sales Office:
Panasonic Semiconductor Sales Asia [PSCSA] Panasonic Industrial Sales (Taiwan) Co., Ltd. [PIST]
300 Beach Road, #16-01, the Concourse, Singapore 199555, the  Head Office:
Republic of Singapore 12th Floor, No.9, SongGao Rd., Taipei 110, Taiwan
Tel:65-6396-8811 Fax:65-6396-8822 Tel:886-2-2757-1900 Fax:886-2-2757-1906
 Malaysia Sales Office:  Southern Area Office:
Panasonic Industrial Company (M) Sdn. Bhd. [PICM] Room B, 5th Floor, No.35, Yongda 5th Rd., Yongkang City,
 Head Office: Tainan, 710, Taiwan
15th Floor, Menara IGB, Mid Valley City, Lingkaran Syed Tel:886-6-203-2880 Fax:886-6-201-8025
Putra, 59200 Kuala Lumpur, Malaysia  Korea Sales Office:
Tel:60-3-2297-6888 Fax:60-6-2284-6898 Panasonic Industrial Korea Co., Ltd. [PIKL]
 Penang Office: 4th Floor, C Square Building, 61-21, Taepyeongno-1ga,
Suite 01-3A, 7th Floor, Menara IJM Land, Jung-gu, Seoul, 100-756, Korea
1, Lebuh Tunku Kudin 3, 11700 Gelugor, Penang, Malaysia Tel:82-2-795-9600 Fax:82-2-795-1542
Tel: 60-4-6531-888 Fax:60-4-6531-897
 Johor Sales Office:
Menara Pelangi, Suite8.3A, 8th Floor, No.2, Jalan Kuning, Taman
Pelangi, 80400 Johor Bahru, Johor, Malaysia
Tel:60-7-331-3822 Fax:60-7-355-3996

Semiconductor Company, Panasonic Corporation

Nagaokakyo, Kyoto 617-8520, Japan
Tel:075-951-8151
http://panasonic.net/sc/en
20090114 Printed in Japan