DIGITAL PID CONTROLLER

T30 SERIES PID Controller

User's Manual

r i d
H yb ntr olle
r+T
imer

PI D co

T30 SE R IES
Downloaded from www.Manualslib.com manuals search engine
 Useful Features !
Enhance hot key between
group menus
sEt.n
< General Setting
group >

rn
tu
re
nu
me
n of
F u n c tio

+ iosE.2
< Input.output
Setting group >

If you press the up key

while pressing the set key ORG.1
< Initial setting group >
in any setting menu,
you can move to the
corresponding upper menu
and move to the desired menu immediately.

※ Use the menu return function to speed up

the setting up to 10 times faster.

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER
Thank you for purchasing the T30 series from Temcoline.
The T30 series is a precision industrial controller that uses an advanced
2 degree-of-freedom (DOF) algorithm.
The T30 series consists of 5 models, which are T32, T33, T34, T37, and
T39.
This manual explains the installation, the functions, the operation, and
the handling of the products.
Please read the manual thoroughly before using the products.
If any difficulties arise while using our products, please call our customer
service at +82-1588-5439.

Pay attention to the followings!

- Use the products under the conditions specified in this manual.
- Please heed the cautions and warnings listed in this manual.
- The contents of the manual may be changed without notice.
- The product is designed to be used installed on a control panel.
- This manual is copyrighted, and may not be copied in part or in
whole without permission.
- The manufacturer takes no responsibility for direct or indirect damages
caused by careless operation or operation under unpredictable or
risky environments.

Safety requirements!
Safety requirements are intended to prevent accidents and dangers
through the proper use of the products, so please heed them at all times.
The safety requirements are divided into "cautions" and "warnings", which
indicate the following.

Serious injury or death may be caused

WARNING if instructions are not observed.

Failure to observe these instructions

CAUTION may cause damage to the instrument
or some injury to the user.

2
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

WARNING
1. Use a separate safety device when this product is used to control a device
that could harm lives or expensive property in the event of a malfunction or a
breakdown. (This may cause fires, deaths, or damage to property.)

2. Do not use this controller at place where there are flammable or

explosive gas. (It may cause a fire or explosion.)
3. Before turning the power on, please check that wiring is correct to the
number of terminal. (It may cause a fire.)
4. Turn off the power during wiring and maintenance to avoid an electric shock.

5. Do not touch the terminals when it is power on. (It may give an electric
shock.)
6. This controller must be mounted on the panel to avoid an electric
shock.
7. Do not attempt to disassemble, modify and repair.

CAUTION
1. Please conduct an inspection when water has entered the product.
(It may cause short circuits, fires, and malfunction.)
2. This controller should be used indoors.
(It may shorten the controller's life or give an electric shock.)
3. Observe the rated voltage and specification.
(It may cause a fire or shorten the controller's life.)
4. Be careful that any of foreign materials do not inflow into the controller. (It
may cause a fire or malfunction of the controller.)
5. Do not give direct vibration or shock to the controller.
(It may cause of malfunction of the controller.)
6. Do not use chemical detergent or solvent, but use a dry towel in cleaning
the controller.(It may cause an electric shock or a fire.)
7. Please check the polarity of power before wiring and connecting the sensor. (It
may cause an electric shock or explosion.)

3
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

Contents
1. Ordering Information 5
2. Input ranges & Output configuration 7
3. Dimensions & Panel cutouts 9
4. Terminal Arrangements & Wirings 12
5. Ratings & Specifications 14
6. Features & Function 15
7. Check points before using 16
8. Initial installation & Min. operation procedures 17
9. Entering into "set menu" & Setting method 18
10. Flow chart (Parameter structure) 21
11. Setting mode 22
12. Alarm(ALARM1, 2, 3) setting 25
13. Details explanation of primary function 27
1) Auto tuning(AT) function 27
2) Manipulated variable(Mvn) check mode 27
3) Alarm(ALARM1, 2) function 28
4) Retransmission output 29
5) Input function 30
6) Selection function for Hysteresis 31
7) SV1, 2 set up control by external contact signal 32
8) Set value "LOCK" function 32
9) Error indication during operation 32
14. SOAK alam and Timer output 32
1) SOAK alam and Timer output 32
2) Timer Normal, T1~5 Output operation timing chart 33
4
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

1. Ordering Information
1)
T 3 -
(4) Power supply voltage
(3) Optional function
(2) Control mode
(1) Size
(1) Size
Code Model Size Remarks
2 T32-SERIES 48(W) x 96(H) x 77(D) No option (Basic function)
3 T33-SERIES 96(W) x 48(H) x 77(D) No option (Basic function)
4 T34-SERIES 48(W) x 48(H) x 77(D) Option : 0, 1, 3
7 T37-SERIES 72(W) x 72(H) x 77(D) Option : 0, 3
9 T39-SERIES 96(W) x 96(H) x 77(D) No option (Basic function)

(2) Control mode

Code Description Remarks
S SINGLE : Standard Heating or Cooling control

(3) Optional function

Model Code Description Remarks
RELAY output 1, Alarm output 2,
T32, T33 SCR(4~20mA), SSR(Voltage pulse) 1, No function
0
SERIES RET(4~20mA Retransmission output) (Basic function S0x)
D.I(SV2, 3) External input

Basic function +
RELAY output 1 (ALARM or MAIN),
0 Option code
SCR(4~20mA), SSR(Voltage pulse) 1
T34 (0 : No option)
SERIES
1 RET(4~20mA Retransmission), Alarm 2 Ex.) T34-S10

3 D.I(SV2, 3) External input, Alarm output 2 Ex.) T34-S30

Basic function +
RELAY output 1, Alarm output 2,
T37 0 Option code
SCR(4~20mA), SSR(Voltage pulse) 1
SERIES (0 : No option)
3 D.I(SV2, 3), RET(4~20mA Retransmission) Ex.) T37-S30
RELAY output 1, Alarm output 2,
T39 SCR(4~20mA), SSR(Voltage pulse) 1, No function
0
SERIES RET(4~20mA Retransmission output) (Basic function S0x)
D.I(SV2, 3) External input

5
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

(4) Power supply voltage

Code Description Remarks
0 100 ~ 240 V AC General-purpose usage
1 24V AC or DC Alternating or Direct current usage

2) Example of model building

Ex.) T34-S00
(1) Size : 48(W) x 48(H) x 77(D) "4"
(2) Control mode : SINGLE "S"
(3) Optional function : Basic function "0" T34-S00
(4) Supply voltage : 100~240V AC "0"

Ex.) T37-S30
(1) Size : 72(W) x 72(H) x 77(D) "7"
(2) Control mode : SINGLE "S"
(3) Optional function : DI(SV1,2), RET "3" T37-S30
(4) Supply voltage : 100~240V AC "0"

6
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

2. Input ranges and Output configuration

1) Input ranges ※ The T30 series has multiple inputs, which may be set and changed by the user.

Input type Setting

Input Code Temperature range Accuracy Remarks
1 -200 ~ 1370
K
2 -199.9 ~ 999.9

15 -200 ~ 1000
J
3 -199.9 ~ 999.9

16 -200 ~ 1000
E
4 -199.9 ~ 999.9

T 5 -199.9 ~ 400.0

Thermocouple R 6 0 ~ 1700
* F.S is max. value
(T.C)
B 7 400 ~ 1800
to min. value of
S 8 0 ~ 1700 ±0.3% of each range.
F.S + 1 Digit * Digit is minimum
17 -200 ~ 900
L of display.
9 -199.9 ~ 900.0

N 10 -200 ~ 1300

U 11 -199.9 ~ 400.0

C (W5) 12 0 ~ 2300

D (W3) 13 0 ~ 2400

JP t100 20 -199.9 ~ 500.0

(JIS, KS) 22 -200 ~ 500
RTD
Pt 100 21 -199.9 ~ 640.0
(DIN, IEC) 23 -200 ~ 640

0~100 mV DC 33 0 ~ 100 mV DC ※ When using 1~5V input

(30), the interior jumper
Voltage
(V DC/mV DC)
-10~20 mV DC 32 -10 ~ 20 mV DC switch must be relocated.

1~5 V DC 30 1~5 V DC

When using current input,

Current 4~20 mA DC 30 use the resistor 250 on
input terminal.

※ How to change the interior switch when using 1~5V input

MULT-IN MODE IN 1~5V ONLY MODE

① Remove plate or take out ② Move and insert the ③ Relocated jumper as
the main cover. jumper that pulled by above and attach plate
tweezers. or mounted cover.
7
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER
2) Output configuration
※ The figure on the left uses
The T30 series
has multiple outputs.
the terminal socket of
T37-S30 as an example
to illustrate the output
response relationship.

OUTPUT-1 OUTPUT-1 (ALARM 1,2)

General Setting
SSR/SCR OUTPUT
type number Relay output AL1 output AL2 output SCR output
SSR output SCR output
0 OUT(ON/OFF) ALM3(ALM1) - RET

1 ALM3(ALM1) OUT(PID) - RET

T30-SXX ALARM1 ALARM2
2 ALM3(ALM1) - OUT(PID) RET

3 OUT(PID) ALM3(ALM1) - RET

(1) Summary and explanation of output settings

Relay output of ON/OFF control [ Output setting number : 0 ]
This is a simple on/off control, mainly used to control cooling devices.
SSR output of PID control (Voltage pulse) [ Output setting number : 1 ]
This is the most widely used setting, and the default value at the point of manufacture.
SCR output of PID control (4~20mA current output) [ Output setting number : 2 ]
This setting is used mainly with thyristor power regulator (TPR) modules,
and is capable of precision control.
Relay output of PID control [ Output setting number : 3 ]
This is the most cost-efficient method of implementing PID control and is used mainly
with magnetic switches (electric switches). However, it may wear the contact point,
and is difficult to use in places that require fast response.
(2) Main relay control output and alarm output
1(SSR) or 2(SCR) 0(ON/OFF)
or 3(RELAY)

ALARM1 or ALARM1 or
3 output 3 output

Control output
Control output
※ It is only for T34-S00!

The T30 series can use up to three alarms independently when using the control
output as SSR (1) or SCR (2). That is, the basic model (no option) can be used as
alarm 1, and the optional model (alarm output) can be used as alarm 3.
8
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

3. Dimensions and Panel cutouts

1) T32 (48x96 mm) Dimensions

45±0.5
48.0 10.0 77.0

Min. 20

92±0.5
96.0

96.0

91.0
Min. 30

T32 / T33 (96x48)

Panel cutouts

(Unit: mm)

2) T33 (96x48 mm) Dimensions

96.0 10.0 77.0

48.0

48.0

43.6

3) T34 (48x48 mm) Dimensions T34 (48x48) Panel cutouts

+0.5
48.0 45 -0
8.8 77.0
+0.5

Min.17
45 -0
48.0
48.0

Min.17
44.9

(Unit: mm)

9
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

4) T37 (72x72 mm) Dimensions T37 (72x72) Panel cutouts

72.0 9.0 77.0 68±0.5

Min. 20

68±0.5
72.0
72.0

67.0
Min. 30

(Unit: mm)

5) T39 (96x96 mm) Dimensions

96.0 10.0 77.0

96.0
96.0

92±0.5 91.0

T39 (96x96)
92±0.5

Panel cutouts

Min. 30

Min. 20

(Unit: mm)

10
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

6) Installation
(1) T34-SERIES
① Bore a hole in the panel, referring to the panel cutouts on the previous page.
② Insert this device into the front of the panel.
③ After inserting two brackets into the holes on the left and right respectively
of the device, Slide it forward until it fits tightly to the panel and secure.

Panel Panel

Bracket hole

(2) T32 / T33 / T37 / T39-SERIES

① Bore a hole in the panel, referring to the panel cutouts on the previous page.
② Insert this device into the front of the panel.
③ Insert 2 brackets, one each on the B/K holes on the top and the bottom
of the device.
④ Secure using screws on the two locations at top and bottom.

Hole of fixing screw Hole of fixing screw

Bracket hole Bracket hole Turn the screw

2-3 times after
contact with panel.

[ figure 1 ] Top side [ figure 2 ] Bottom side [ figure 3 ] Fixing completion

11
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

4. Terminal arrangements and Wirings

1) T32 (48x96 mm), T33 (96x48 mm) T32/33 T3
T32, T33

N.C

2017. 5

2) T34 (48x48 mm)

T34 OPTION
Option 1 Option 3
(T34-S1x) (T34-S3x)

T5

12
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER
2/33 T37 T39
3) T37 (72x72 mm) T32/33 T37
T37
Option 3
(T37-S3x)

OPTION
N.C
2017. 5. 25. 수정
4) T39 (96x96 mm) 2017. 5. 25. 수정
※ Terminal explanation (T39-S00)

T39T39 Terminal : OUT1 only for output

N.C
selection no. 0, 3 (Relay output) mode.
Terminal : OUT1 only for output.
selection no. 1, 2 (SSR, SCR output) mode.
Terminal : RET(Retransmission 4~20mA)
or for power of sensor SPS. (DC 15V)
T59
T57 Terminal : Power supply terminal.

Terminal T57
: Alarm1 output terminal.

Terminal : Alarm2 output terminal.

Terminal : The external D.I input

terminal may be used when (DIS=ON), and
the target value may be controlled. (SV1, SV2)
Terminal : Input terminals.

N.C

13
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

5. Ratings and Specifications

Model T30-SERIES

Rating 100~240V AC 50~60Hz (voltage operating range: 85~265V AC)

Power supply
※ Option: Rating 24V AC or DC (voltage operating range: 20~28V DC)

Power consumption 5VA (Max.)

TC: K, J, T, E, R, B, S, L, N, U, C(W5), D(W3)

Platinum RTD: KPt100(KS), JPt100(JIS), Pt100(DIN)
Input Type
Current input(A): 4~20mA DC
Voltage input(V): 1~5V DC, -10~20mV DC, 0~100mV DC

Display Accuracy ±0.3% of FS +1 Digit

Current input (250 ), Voltage input (TC included) ≥ 1M

Input Impedance
(RTD line resistance : ≤ 10 , when 3-line resistance are the same)

Input sampling period 50~250ms (variable according to SG-PID algorithm)

1c 250V AC, 3A(resistance load) electric lifespan ≥ 100,000
Relay
(time proportional PID output or ON/OFF output)
Control Voltage DC15V 25mA (built-in short protection circuit)
Output (S.S.R) Voltage pulse (time proportional PID output)
Current 4~20mA DC, load impedance ≤ 600 (continuous PID output)
(S.C.R)
Super 2 degree-of-freedom PID (SG-PID algorithm),
Control Method
Auto-Tuning
Multi SV Input (D.I) ON : ≤ 1K , OFF : ≥ 100K (external control SV1,2)
4~20mA DC, load impedance ≤ 600 resolution 1/4,600
Retransmission Output PV(process value), SV(set value), MV(manipulated variable[%]),
SPS(sensor module power supply)
1a 250V AC 3A (resistance load) 20 type of independent event
ALARM 1
Alarm output output & Control loop break alarm
(Alarm 1,2,3) ALARM 2 Convenient timer output 6 types (SOAK ALARM external timer
ALARM 3 mode T1 to T5) Inverter operation (RUN) / stop (STOP) control
Ambient temperature -10~50℃ / relative humidity 25~85% RH
and Humidity (but with neither condensation nor freezing)

Weight T32, T33, T37 : 230g T34 : 140g T39 : 320g

(Bracket, Accessories included) ※ + 30g, if options are added

14
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

6. Features and Function (ex. T34 SERIES)

① Process value (PV)

display (Red color)

② Auto tuning (AT) lamp

③ Set value (SV)

display (Green color)

⑩ Set value Up key

⑨ Set value Down key

⑧ Shift key
⑦ Storage & Function key

④ Control output lamp

⑤ SV2 display lamp
⑥ Alarm output lamp
※ Description

Name Function
① Process value Display the process value. (red color)

② Auto tuning lamp Flash every 0.5 second during auto tuning.

③ Set value display Display the set value, codes, and modes.

④ Control output lamp Lights when the control output is ON.

⑤ SV2 display lamp Lights when the SV2 is displayed.

⑥ Alarm output lamp Lights during the alarm is ON.

⑦ Function key Use to move the menus, to store, and to operate.

⑧ Shift key Use to shift the digits.

⑨ Set value down key Use to decrease set value and to move the menu.

⑩ Set value up key Use to increase set value and to move the menu.

15
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

7. Check Points before Using

1) Default values at the point of manufacture
The default input and output values of the product at the point of manufacture
are as follows.

Input : K-Type (Code No. 1) Output : SSR (Code No. 1)

※ When selecting SSR (1), SCR (2) output mode only for model T34-S00
(no option), alarm 1 is output as MAIN RELAY. For models with other alarm
options, alarm 3 is output as MAIN RELAY. (Refer to the page 8 for details)

2) 7 Segment display indications

3) Initial display on power supply (T34 SERIES basis)

Model Name Option indication
0 : Basic type (No option)
1 : RET, ALARM1, 2
3 : DI(SV1, 2), ALARM1, 2

Output type indication

0 : RELAY ON/OFF control
1 : SSR (VOLT-PULSE) PID control
2 : SCR (4~20mA) PID control
3 : RELAY PID control
Input type indication
01 : K-Type (-200~1370 ℃)
02 : K-type (-199.9~999.9 ℃)

Firmware version display 33 : mV DC (0~100 mV)

16
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

8. Initial installation and Minimum operation procedures

The following are the instructions for initial installation and minimum operation
procedures. Please read the contents of this manual, including the general functions
outlined here, as thoroughly as possible before operating the device.

1) Check the external wiring diagram and specifications.

(power supply and terminal arrangement)
2) Check input and output specifications!
The default setting for the T30 series at the point of manufacturer are as follows.

Input : K-Type (setting code 1 : -200 ~1370℃)

Output : SSR mode (setting code 1)

If you wish to change the input or the output type, please select the option you
desire on the input group and the output group menus.

※ The input type settings must be configured first before changes to other set values
are made.

When the input type is changed, all other parameters (set values) are reverted to
their factory default.

3) Select the desired set value (SV).

4) Please set auto-tuning or P, I, D values to suit the operating environment.

Auto-tuning is recommended except under special circumstances.

※
※ 다이렉트
※ 다이렉트 메뉴이동
메뉴이동
Direct menu 및 진입
및 진입
navigation 키(단축
키(단축
and 키)
entry키) 지원
key지원
(hot key) support
※ 다이렉트 메뉴이동 및 진입 키(단축 키) 지원
템코라인
T30
템코라인 T30은hot
supports
T30은 사용자
사용자 편의를
keys편의를 위해서
for user
위해서 단축 키(Hot
키(Hot Key)를
convenience.
단축 Key)를 지원합니다.
지원합니다.
템코라인 T30은 사용자 편의를 위해서 단축 키(Hot Key)를 지원합니다.
1.
1.
1. :: To
기본
기본enter
설정메뉴
설정메뉴general
진입
진입 setting
키
키 mode
1. : 기본 설정메뉴 진입 키
2.
2. +
+ 3 seconds
3초 or more
이상 :: AT
AT 미 실행
실행 : To
시,enter
입/출력 input/output
설정모드 진입 setting
진입 단축mode
키
2.
2. + 3초 이상 미
3초 이상 : AT 미 실행when
시, 입/출력
시, 입/출력
설정모드
설정모드 진입
AT is not running.
단축
단축
키
키
3.
3. +
+ 이상 :: 초기설정모드
3초 이상 초기설정모드 진입 진입 단축 단축 키 키
3.
3. + 3초
이상 : 초기설정모드
3 seconds
3초 or more : To 진입
enter단축 키 setting mode
initial
4. +
+ 한번클릭 :: 순간이동 순간이동 키 키로 로 임의의
임의의 설정메뉴설정메뉴 위치에서,위치에서,
4.
4.
4. + 한번클릭
One click: : SET
한번클릭 순간이동
Function
SET
키
of
키를 누른상태에서
키를
로 임의의
menu
누른상태에서 UP 설정메뉴
return, At
UP 키를 any
키를 한번 위치에서,
setting
한번 menu position,
클릭하면
클릭하면
if you
SET 키를press the UP keyUP
누른상태에서 while
키를 holding
한번 the SET key, it moves
클릭하면
현재의 메뉴에
현재의 메뉴에 해당되는 해당되는 처음의 처음의 위치로 위치로 순간 순간 이동됩니다.
이동됩니다.
to the 메뉴에
현재의 first position
해당되는 corresponding
처음의 위치로 to the
순간 current
이동됩니다.menu.
5. +
+ 0.5초 이상이상:: :: 오토튜닝
오토튜닝 단축
or more 단축 키
5.
5. + 0.5초
0.5 seconds
0.5초 이상: : 오토튜닝
키
: Auto
단축 키turning hot key
17
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

9. Entering into "set menu" and Setting method

1) Input & Output type setting
Temcoline products are universalized input and
output. Please set up input and output type firstly
and use when install our unit.
The method for input and output setting menu before
auto-tuning.
Caution ! When auto tuning is completed normally, the input / output menu is
locked for safety. Refer to the next page (P, 19) for how to How to Disable.

① Press + key more than 3 seconds, Entering into input & output setting menu.

② Input type setting : Select the desired input sensor type.

(setting code 1~33 / refer to P7, Input ranges)
INPUT(T.C) CODE TEMP. RANGE INPUT(RTD) CODE TEMP. RANGE
1 -200 ~ 1370
K 20 -199.9 ~ 500.0
2 -199.9 ~ 999.9 J P t100
(JIS, KS)
15 -200 ~ 1000 22 -200 ~ 500
J
3 -199.9 ~ 999.9
21 -199.9 ~ 640.0
16 -200 ~ 1000 P t100
E (DIN, IEC)
4 -199.9 ~ 999.9 23 -200 ~ 640
T 5 -199.9 ~ 400.0
R 6 0 ~ 1700 INPUT(V DC/mV DC) CODE
B 7 400 ~ 1800
0 ~ 100 mV DC 33
S 8 0 ~ 1700
17 -200 ~ 900 -10 ~ 20 mV DC 32
L
9 -199.9 ~ 900.0
1 ~ 5 V DC
N 10 -200 ~ 1300
U 11 -199.9 ~ 400.0 30
4 ~ 20mA DC
C (W5) 12 0 ~ 2300 (Use 250 resistor.)
D (W3) 13 0 ~ 2400

③ Output type setting : Select the desired output type.

(setting code 0~3 / refer to P8, Output Configuration)
S ETTIN G CONTROL OUTPUT
CODE
0 RELAY ON/OFF CONTROL
1 SSR (Volt-Pulse) P.I.D CONTROL
2 SCR (4~20mA) P.I.D CONTROL
3 RELAY P.I.D CONTROL

※ Even if PID control output (1, 2, 3) is selected, ON / OFF control mode can
also be used when P value is OFF.
④ Manipulated Variable Display setting [%]
It works when display the manipulated variable (0~100%) at
operating menu.
18
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

2) The processing for input/output setting menu after auto-tuning

After auto-tuning has done of T30 series models, to avoid any user's mistake,
input/output setting menu is restricted automatically. But you can change input/
output by following ways. However, unit will be returned to factory default when
changed input type.

While normal using our products,

the method for input/output setting
menu after auto-tuning.

※ Describe how to enter by using hot keys.

<Initial setting menu>

Return to the
① + operating menu.
(Will return
more than 3 sec. automatically)

②
IOSE=ON ③ +
more than 3 sec.

<In/output setting menu>

※ Press + more than 3 seconds at the inital set. (before running auto-tuning)

19
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

3) Set value(SV) setting [ in condition of Mvn = OFF (basic) ]

① Enter to setting mode by key

② Set a desired value by key
③ Store a value by key

4) Auto tuning

AT operation start : + 0.5 second

AT stop by perforce : + 0.5 second

AT command lamp (flash every 0.5 sec.)

Auto-tuning is required before operating for the first time. Set the target value(SV) in the
range mainly used and run auto-tuning. When auto-tuning begins, the "auto-tuning command
lamp" will flash every 0.5 second and will turn off upon completion of the auto-tuning
process. Please refrain from operating the keys while auto-tuning is in progress.

※순간이동기능
※ Function of menu return

편리한 Features
※ Useful 기능
※Use
※ 순간이동 기능을
the menu return function

to사용하면 설정속도가
speed up the setting
+ 최대 10배까지 빨라
up to 10 times faster.
임의의
집니다.
If you press(위치)
the up key
설정 메뉴에서
while pressing the set key
SET키를 누른상태 ORG.1
in any setting menu,
에서 UP키를 누르면 < 초기설정 그룹 >
you can move to the
해당되는 상위 (그룹)
corresponding
메뉴로 순간이동하여 upper menu
빠르게
and 원하는 메뉴로 desired
move to the 이동할 menu immediately.
수 있습니다.

20
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

10. Flow Chart (Parameter structure)

※ To enter 'Input/Output settings' by 'IOSE' on is valid for only time. If you want to enter
'Input/Output settings' again you must turn on 'IOSE' first. If there is no Key action the
'IOSE' will be OFF automatically in 50 seconds.
21
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

11. Setting mode

1) General setting mode
The general setting mode is for changing environment parameters on ad hoc basis and
also for tuning performance enhancement and configuring other functionalities.
Display Description Setting range Condition Initial value
Display general setting
- - -
mode

D.I Option
Set value 1 (SV1) setting EU (0 ~ 100 %) EU (0 %)
in use

D.I Option
Set value 2 (SV2) setting EU (0 ~ 100 %) EU (0 %)
in use

Set value of alarm 1 (AL1) EU (0 ~ 100 %) Use Alarm 1 EU (100 %)

Set value of alarm 2 (AL2) EU (0 ~ 100 %) Use Alarm 2 EU (0 %)

Selection of (SV1, 2) number 1/2 Always 1

SV1, 2 proportional band (P) OFF/ 0.1 ~ 999.9 ℃

PID control 20.0 ℃
(ON/OFF control)

SV1, 2 Integral time (I) OFF / 1 ~ 6000 sec. PID control 240 sec.

SV1, 2 Differential time (D) OFF / 1 ~ 6000 sec. PID control 60 sec.

SV1, 2 Manual reset (MR) -5.0 ~ 105.0 % Integral time

50.0 %
OFF

PID control
Cycle Time (P.I.D Control Only) 1 ~ 1000 sec. 2 sec.
(SSR or RELAY)

EUS (0 ~ 100 %) ON/OFF

Hysteresis (ON/OFF control) 2℃
control

Select the operational method ON/OFF

of Hysteresis HALF / NORMAL NORMAL
control

OFF / 1 ~ 9999 sec. ALARM1

Control loop break alarm (LBA) 480 sec.
No. 21 selection

Highest limit of retransmission

(RET.H) Use EU (100 %)
TC/RTD : _IN.H~_IN.L
retransmission
DCV IN : _SL.H~_SL.L
and select
lowest limit of retransmission ( But, RET.H ＞ RET.L )
PV or SV EU (0 %)
(RET.L)

22
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

※ EU : An engineering unit in compliance with the input range

Ex.) Inputselection
ex) Input selection
no. no.
: 01 :(K-TYPE)
01 (K-TYPE)
EU 0 % = -200 INPUT -200 0 1370 [℃]

EU 100 % = 1370 EU 0 100 [%]

INPUT -200 0 1370 [℃]

EUS 0 %=0 (0) ( 200 ) ( 1570 )
EUS 100 % = 1570
EUS 0 100 [%]

2) Initial setting mode

The initial setting mode is for setting up initial parameters and configuration for
overall control and functionalities activation that are rarely changed after the initial
setup.
Display Description Setting range Condition Initial value

Initial set mode (ORG.1) - - -

I/O setting entry switch ON / OFF OFF

Always
(IOSE)

Set highest input range

Within input range 1370
(_IN.H)
(See input type and
Always
range)
Set lowest input range But, _IN.H ＞ _IN.L
(_IN.L) -200

Set input digital filter value

OFF / 1~120 sec. Always OFF
(_FLT)

Input value correction (_INS) EUS (-100.0~100.0 %) Always EUS (0.0 %)

Correcting upper limit(Gain) of On voltage

EUS (-100.0~100.0 %) EUS (0.0 %)
input (_ING) input

Input temperature unit selection ℃/℉ Always ℃

(Fixed Celsius)

Select the decimal point position

in Voltage input mode (_DPP) 0~3 1

Voltage or
Free scale upper limit set 4~20mA
-1999 ~ 9999 100.0
(voltage input mode) input mode
But , SL-H ＞ SL-L
Decimal point only
Free scale lower limit set positioning by _DPP 0.0
(voltage input mode)

Output action selection REV (Heating),

Always REV (Heating)
DIR (Cooling)

Select alarm 1 output type OFF / 1 ~ 21(LBA)

Always 3
(See alarm type)

23
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

Display Description Setting range Condition Initial value

OFF / 1 ~ 20 Using alarm
Select alarm 2 output type 4
(See alarm type) 1, 2 option

OFF / 1 ~ 20 Using alarm

Select alarm 3 output type OFF
(See alarm type) 1, 2 option

Hysteresis of alarm 1 output EUS (0.0 ~ 100.0 %) Using alarm1 1℃

(1~20)

Hysteresis of alarm 2 output EUS (0.0 ~ 100.0 %) Using alarm2 1℃

Delay time of alarm 1 OFF / 1~240 sec. Using alarm1 OFF

Delay time of alarm 2 and Timer OFF / 1 ~ 5999 sec. Using alarm2
Timer T4 and T5 OFF
output, T4, T5 Time setting and Timer

External contact input (SV1, 2) Using

OFF / ON OFF
ON/OFF switch DI option

Retransmission type PV/ SV/ MV/ SPS Using

PV
or SPS selection RET option

Set data protection OFF/ ON/ ALL Always OFF

3) In/Output setting mode

The input/output setting mode is a parameter for the first time use. It's a
hardware configuration so requires special user caution. That is, the
configuration is determined by the type of equipment and it must be
configured first. (※ all parameters are initialized according to the entered
input type.)
Display Description Setting range Condition Initial value

In/output setting mode - - -

1 ~ 33
Input type selection (_InP) Always 1
(refer to P7, 2. 1)

Output type selection (_out) 0~3

Always 1
(refer to P8, 2. 2)

Manipulated variable (_Mvn)

OFF / ON Always OFF
Display setting

When the input type is changed, all parameters are reverted to their factory
When the input type is changed, all parameters are reverted to their factory default.
default. This means that before using the T30, the input type needs to
This means that before using the T30, the input type needs to be set first, after
be set first, after which other parameters can be configured.
which other parameters can be configured. If the input settings are changed while
If the input settings are changed while in use, auto-tuning and
in use, auto-tuning and other parameters need to be reconfigured.
other parameters need to be reconfigured.
24
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

12. Alarm(ALARM1, 2, 3) Setting

The T30 series has up to three independent alarm outputs, and you can set up to 21
alarm types, hysteresis, and delay time.

Set value of alarm 1 Type of alarm 1

<General set mode> <Initial set mode> Type of alarm 2

Set value of alarm 2
3 sec. + 3 sec.
Type of alarm 3

Loop break alarm Hysteresis of alarm 1

*Type of alarm 1 (When _A1.t = 21)
Hysteresis of alarm 2

Hysteresis of alarm 3
※ When the control output is selected as SSR (1) or SCR (2),
Delay time of alarm 1
the main output relay can be used as alarm 3
Delay time of alarm 2

1) Inverter operation start / stop function

The T30 series supports operation start / stop function during inverter control
(4 ~ 20mA) to enable more stable control and solve the problems of lifetime and
power saving of peripheral devices

Alam 1 setting Alam1 type setting

< General set mode > < Initial setting menu >
Inverter start point Alam2 type setting
3 sec. (0 ~ 100%) 3 sec.
or more
6% set (operation start point) Alam3 type setting " NO. 21"
(Inverter operation/stop output)

Hysteresis

Delay time(stop delay)

Inverter operation/stop output

Hysteresis (2%)

Operates when using Alam output! 2) Hold function

the hold function When the low limit alarm is used, if
the temperature before the power
Process values
(PV) supply is lower than the set value,
Low unnecessary low limit alarm occurs
limit alarm
until the normal control temperature is
Alarm time!
(Holding!) reached.
At this time, when the hold function
is used, it is possible to ignore the
Power ON (HOLD)
occurrence of the alarm up to the
Alarm output
normal control temperature when the
initial power is turned on when the
25 temperature is within the alarm range.
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

2) Alarm output type and Selection code

CODE NO. ALARM TYPE ALARM OUTPUT OPERATION
01 Absolute value upper-limit When temperature OFF ON
is falling
09 Process low When temperature OFF ON
is rising Hysteresis

11 Process high with hold

OFF ON

19 Process low with hold Low High

Alarm setting value

02 Absolute value lower-limit When temperature ON OFF

is falling
10 Process low When temperature ON OFF
is rising Hysteresis

12 Process high with hold ON OFF

Temperature
20 Low High
Process low with hold Alarm setting value

03 Upper-limit deviation <Negative temp. value setting> <Positive temp. value setting>
When tem-
perature is OFF ON OFF ON
05 Process low falling
When tem-
OFF
perature is ON OFF ON
rising Hysteresis Hysteresis
13 Process high with hold
OFF ON OFF ON
Temperature
Low - High Low High
15 Process low with hold -Alarm SV SV Alarm
setting value

04 Lower-limit deviation
When tem-
<Negative temp. value setting> <Positive temp. value setting>
perature is ON OFF ON OFF
06 Process low falling
When tem- ON OFF ON OFF
perature is
rising Hysteresis Hysteresis
14 Process high with hold ON OFF ON OFF
Temperature
Low - High Low High
16 Process low with hold SV -Alarm Alarm SV

When temperature
Upper & Lower-limit is falling
ON OFF ON
07 deviation When temperature ON OFF ON
is rising
Hysteresis

Upper & Lower-limit ON OFF ON

17 deviation with hold Temperature
Low High
Alarm SV Alarm

Upper & Lower-limit When temperature OFF ON OFF

08 deviation in range
is falling
When temperature OFF ON OFF
is rising Hysteresis
Upper & Lower-limit ON
OFF OFF
18 deviation in range Temperature
Low High
with hold Alarm SV Alarm

ALARM 1 Loop break alarm (LBA) Refer to page 28 LBA ! (ALARM1 only)
Inverter operation / stop
21 ALARM 3 output alarm Page 25, 1) Refer to inverter operation stop control! (ALARM 3 only)

[Alarm No. 2 code 21] Supports five kinds of SOAK alarm and timer output (Process high)
(Setting mode T1 to T5)
ALARM 2
[Alarm No. 2 code 22] SOAK Alarm and Timer Output (Process low) refer to
22
* Page 33, "14. SOAK alarm and timer output mode ".

When alarm type reverse-correspondence is selected for alarm type and code, please be
aware that when the alarm lamp turns on, the contact output will be off.
26
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

13. Details explanation of primary function

1) Auto tuning (AT) function
Before the PID temperature controller can be used for the first time, the P, I, D values
must be tuned. The auto-tuning function finds the optimal value by tuning automatically
according to the load factor and other conditions.
Please make sure that the controller is tuned before using it for the first time, by defining
the set values in the most frequently used range and running auto-tuning.
When auto-tuning begins, the "auto-tuning command lamp" will flash every 0.5 second
and will turn off upon completion of the tuning process.
Please refrain from operating the keys while auto-tuning is in progress.

AT operation start : + 0.5 second

AT stop by perforce : + 0.5 second

AT command lamp (flash every 0.5sec.)

※ Do not use auto tuning under below Process.
- Rapid control Process such as Flow, input control.
- Process which should not ON/OFF output even a temporary.
- Process which should not over load at control.

2) Manipulated Variable [%] (Mvn) check mode

"Mvn [%] check function" displays the control output
< Setting method > “Mvn [%] 확인기능”은 제
[%], which can be viewed by pressing the " " key
기본운전 모드에서 SET 키
while operating in default operation mode and is shown
as a percentage of the control output 제어출력량(
(0~100[%]) in 0~100 [%] ) 이
the SV display. In this mode, pressing the "
이 모드일" key 때, SET 키를 누름
alternates between showing the SV and the Mvn values,
and changes to the SV value can be made 대로by 표시되고,
" " or 설정 값(S
저 장
save
" ". If required, set in the order of SET 순으로
. 설정합
Refer to P18~19,
I/O Set Mode
< In condition of Mvn = ON >

Operation mode

Escape..
3 sec.

Mvn display screen

Change Save (Present Mvn Out = 85%)

27
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

3) Alarm (ALARM1,2) function

The T30 series alarm outputs have three independent alarm outputs and are designed
to be used with a variety of auxiliary outputs as well as simple alarm functions. In the
setting group, 21 types of alarms, hysteresis of alarm output and delay time
can be set. (refer to th Page 25 ~ 26 Alarm Settings)

경보1 지연시간 설정
(1) Delay time of alarm

경보11 지연시간
Alarm delay time설정
setting 경보22지연시간
Alarm delay time설정
setting

경보2
The alarm delay 지연시간
function is a설정
function that waits for the set time when
the alarm output is generated and then outputs the alarm output.
Actual applications can be used for various auxiliary output functions
rather than alarm delay.

If you set the alarm delay time, alarm (1 or 2) output waits for the delay time after
receiving the alarm. However, it is not applicable when the alarm is turns off.
During the delay time the alarm (ALM) output lamp blink 0.5 second intervals to
displays the current alarm is waiting to alert.

(2) LBA (Control Loop Break Alarm)

LBA is functionality where it triggers an alarm when there is no change in input
while the difference is in consistent state (it assumes there is certain problem in
the control loop). Therefore if the control loop is not in a normal working mode,
it can be utilized for detection. E.g. output is generated if there are problems with
control unit and other problems or can be used for heater disconnection.

① How to set up
Please set value of LBA two times of the normal integral time setting.
In addition, LBA can be set to automatically by the auto turning function.
In this case value will be set up automatically two times of integral times.

② Description of operation
Control loop break alarm consists to alert you Control loop break by detect
Variation during setting time when P.I.D calculations (On time/period of output)
is 0% or 100%.
ⅰ. When P.I.D calculations stays 100% more than LBA setting time, Break
alarm will be turned on if calculations is not increase more than 2℃.
(In positive action will turned on if calculations does not fall more than 2 ℃.)
ⅱ. When P.I.D calculations stays 0% more than LBA setting time, Break
alarm will be turned on if calculations is not fall more than 2℃.
(In positive action it will turned on if calculations does not increase more
than 2 ℃.)

28
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

③ Cause of activation
LBA will activate below condition.
ⅰ. Abnormalities of the control target : Heater break, No supply voltage,
`Wrong wiring, etc.
ⅱ. Abnormalities of the sensor : Disconnection / short circuit of sensor
ⅲ. Abnormalities of the handling tools : Splice relay, wrong wiring, etc.
ⅳ. Abnormalities of Output circuit : Spliced relay inside of unit, break
ON/OFF
ⅴ. Abnormalities of input circuit : No calculations change even input is
change.

④ Notice of LBA
ⅰ. LBA will work when PID calculations is 0% or 100%. Thus the time from
occurring of abnormalities to alarm time will be the time of PID value 0%
or 100% plus.
ⅱ. LBA set-up times LBA will not working during auto tuning.
ⅲ. The LBA function is influenced by disturbances (heat sources, etc) and
as a result may be activated even if there is no trouble in the controlled
system.
ⅳ. When LBA setting time is too short or wrong control target, sometimes
LBA will be on/off abnormally of not turned on. In this case please set
LBA time little longer.

4) Retransmission output
The re-transmission output of the T30 series has all three transmission functions and
the ability to supply power when using an external sensor.

Retransmission type or SPS selection

Retransmission type or SPS selcetion

PV (Current Progress Value)

PV ( Current
SV (Set Value) Progress Value )
MV (Manipulated Variable)
SV ( Setsupply
SPS (Power Value ) sensor)
for external
MV ( Manipulated Variable ) Scale setting can on
RetransmissionSPS
value ( Power 4.0supply
mA for external sensor
12.0 mA ) retransfer
20.0 mA output se

RET setting : PV or SV RET.L RET.H

MV (Fixed) 0.0 % 100.0 %
SPS (Fixed) DC Power Supply : DC 15V / 25mA

29
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

5) Input function
(1) Digital input filter (_FLT)
This function is useful when suboptimal environments cause noises or severe
fluctuations, enabling a digital software filter. The filter's sensitivity may be set
from off to 1~120 seconds. Please be careful when using this function, as it may
affect the control-related algorithms.
(2) Input value correction (_INS)
This function allows the input values to be compensated. This function is useful,
for example, when sensors cannot be placed at desired locations, or when several
different thermometers are used in conjunction. The values may be compensated
to extent desired by the user.
(3) Correcting upper limit of input vlaue(_ING)
Use only in voltage input(current 4-20mA) mode. This can accurately correct the
deviation occurred by output error of sensor module and an error of conversion
resistance (250 ).
_IN.G
[ 4~20mA INPUT ]

(Maximum) 20.0

16.0

12.0

8.0

(Minimum) 4.0

_IN.S 0 50.0 100.0

(_SL.L) Free Scale Area (_SL.H)

Ex.) When using DC 4~20mA input, the lower value, 4mA can be corrected
at "_INS" mode and higher value, 20mA corrected at "_ING" mode.
To have more accurate correction, firstly set the lower value at "_INS" mode
and then set the higher value at "_ING" mode. T30 series offers the powerful
correction function with 4-20mA conversion resistance (250 ) at competitive
prices.

(4) Setting decimal point position (_DPP), and free scale high and low limits (SL-H, SL-L)
This applies only when using voltage inputs (DC V, mV) or currents between 4
to 20mA (1~5V). The user may set ranges, units and decimal point position as
desired. This can be used not only for temperatures but also for a number of
other measurements, including humidity, pressure, and weight.

30
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

6) Selection function for Hysteresis (ON/OFF control mode _out=0)

T30-series can select Hysteresis operation method in ON/OFF control mode.
(1) HYS.T = “NORM” selection
Hysteresis Hysteresis
ON ON

OFF OFF
_ACT = REV. SV SV
_ACT = DIR.
(heating operation) (Cooling operation)

(2) HYS.T = “HALF” selection

Hysteresis
※ While Hysteresis operation in "HALF" mode,
ON the operation of Heating and cooling is same,
and "NORM" is factory default.
OFF
SV

7) SV1, 2 set up control by External contact signal

Use SV1,2 by external contact (_dis=ON)
SV Action External terminal status

SV1 Select OPEN

ON
SV2 Select SHORT

Block external contact signal

OFF
(Can select under inside menu only)

Digital input switch (_dis) : This function selects whether to use digital input switch.
This function the ability to change SV1, 2 to Each pre-set value by an external contact
signal.
Please use a non-voltage contact (relays, switches) for direct input. If a non-contact
device such as a semiconductor are used, please operate within the ranges, ON=1K ,
OFF=100K .
"SV1, 2" selection menu when the (_dis = OFF)

1 2 T30 controls when the external

or internal SV1 or SV2 select control
by independent P, I, D, MR value.
As a result, it will have best control
performance depending on
the temperature value.
Typically, when use Auto-tuning,
it will work if either SV1 or SV2 tuned
and set same P, I, D value with the other.

31
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER

8) Set value "LOCK" function

Lock function will protect change set value and activate function such as auto tuning
from accidental key operation. Please use after setting prevents.

Lock has
Lock has 33 setting
settingmode
mode(OFF/
(OFF ON/
/ ONALL)
/ ALL)

OFF▪ :OFF
LOCK function
: LOCK off off
function
ON : Can operate SV setting and AT only.
ALL▪ :ON : Can operate
Impossible SVand
all setting setting and ATonly
operation, only.
LOCK OFF is available.
▪ ALL : Impossible all setting and operation, only LOCK OF is available.
9) Error indication during operation
B.OUT : INPUT SENSOR error or burn out etc.
+OVR : Out of maximum input range (refer to input group setting) or overheating
-OVR : Out of minimum input range (refer to input group setting) or overcooling
SYS.E : SYSTEM setting error or Memory damage (request for repair)
RJC.E : RJC Sensor damage or PCB burn (request for repair)
EEP.E : EEPROM damage (request for repair)
COM.E : Communication ERROR (request for repair)
AT.E : Auto Tuning Error, Checking heater break or controller

14. SOAK alarm and timer output

ALARM 2 of the T30 series supports powerful digital timer function. There are 5 types
of timer output mode besides the basic SOAK ALARM function.
1) SOAK alarm and timer output
(1) Alarm type setting (2) Timer mode, unit, deviation setting

Initial setting menu General Settings menu

SOAK Alarm deviation

setting

Alarm 2 type setting

Timer unit setting
21 (contact A) or 22 (contact B)
Min (Min) or Hour (Hour)
selection
Activated only Timer mode setting
when setting timer mode (Normal, T1 ~ T5)
(Press for more than 1.5 seconds)
T4, T5 ※ It is only active
in timer mode.

[ Normal operation [ Time setting and

menu ] information display ] 【 Timer output mode 】
When OFF Time unit (Min / Hour) setting
Min/Hour Sec/Min
If ON, SV2
(Current time remaining)
ⓑ Timer setting
When the unit is time,
Alarm 2 timer output it flashes in seconds (Set time)
ⓐ Present value and Set value
※ When the alarm 2 (Alarm2) is set to timer output, the digit shift key ( ) and
"external input terminal (SV2)" are automatically activated by the timer operation / stop
or reset function.

32
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 DIGITAL PID CONTROLLER
T30-SERIES SOAK ALARM & TIMER OUTPUT MODE

2) Timer normal , T1~5 Output Operation Timing Chart

2) 타이머 Normal, T1~5 출력 동작 타이밍 차트
◈Alarm
◈ 경보설정setting

Selection
선택코드 code 2121(정접)
(precess high)
Soak
Soak Alarm
경보편차 deviation
(Skdv) (SKdv)
선택코드
Selection code 2222(역접)
(process low)

Temp. Set
Value (SV)

Process
Value (PV) Soak
Soak Alarm
경보편차 deviation
(Skdv) (SKdv)

Timer set End.

Norm 1 min 45 s.
Min. Run.. Timer Run.. Timer Run.. Timer
Time Set 1 min 45 s. (1.45 ~ 0.00) 0 min 00 s. 1 min 45 s. (1.45 ~ 0.00) 0 min 00 s. (1.45 ~ 0.00)
(1min. 45 sec)

Timer output OFF ON OFF ON OFF ON

(Alarm 2) AL2 Reset Reset

Reset S/W
( or D.I )
1.5 sec
End.
Timer set
1 min 45 s. (1.45 ~ 0.35)

T1 Run.. Timer Run.. Run.. Timer Run.. Timer

1 min 45 s. (1.45 ~ 0.00) 0 min 35 s. (1.45 ~ 0.00) (1.45 ~ 0.00)
Time Set

Timer output OFF ON OFF OFF ON OFF ON OFF

(Alarm 2) AL2
Stop Start Not valid
Not valid
Start/Stop
( or D.I )
1.5 sec
Timer set End (0.00) Forced stop
1 min 45 s. (1.45 ~ 1.09) (1.09)
T2 Run.. Timer Run.. Timer Timer set Run.. Timer
1 min 45 s. (1.45 ~ 0.00) (1.45 ~ 0.00) 1 min 45 s. (1.45 ~ 0.00)
Time Set

Timer output OFF ON OFF ON OFF OFF ON OFF

(Alarm 2) AL2
Stop
Start Start Not valid Start Start Not valid
(1st) (2nd) (3rd) (4th)
Start/Stop
( or D.I )
1.5 sec
End. Forced stop
Timer set
1 min 45 s. (1.45 ~ 1.09) (1.09)

T3 Run.. Timer Run.. Timer Timer set Run.. Timer Run.. Timer
1 min 45 s. (1.45 ~ 0.00) (1.45 ~ 0.00) 1 min 45 s. (1.45 ~ 0.00) (1.45 ~ 0.00)
Time Set

Timer output OFF ON OFF ON OFF ON OFF ON OFF ON

(Alarm 2) AL2
Stop
Start Start Start Start
Start (4th)
(1st) (2nd) (5th)
Start/Stop (3rd)
( or D.I )
1.5 sec OFF Time Set
OFF Time ON Timer
(1.45 ~ 0.00)
70 sec.
(70 sec.)
T4 ON Time Set ON Timer ON Timer ON Timer OFF ON Timer
1 min 45 s. (1.45 ~ 0.00) (1.45 ~ 0.00) (1.45 ~ 0.00) Timer (1.45 ~ 0.00)
On/Off Time Set

Timer output OFF ON OFF ON OFF ON OFF ON ON OFF

(Alarm 2) AL2

OFF Time Set (1 min 45 s.) Reset period

T5 ON Time Set
ON Timer ON Timer ON Timer OFF Timer ON Timer
70 sec. (70 sec.) (70 sec.) (70 sec.) (1.45 ~ 0.00) (70 sec.)
On/Off Time Set

Timer output OFF ON OFF ON OFF ON OFF ON ON OFF

(Alarm 2) AL2
Reset
Reset S/W
( or D.I )
1.5 sec

POWER ON

33
www.temcoline.com

Downloaded from www.Manualslib.com manuals search engine

 Rev. 301701-01
www.temcoline.com

TEMCOLINE Co., Ltd.

Misung Bldg, 217-1, Gurojungang-ro, Guro-gu, Seoul, 08216 Korea
Tel. +82-2-3667-5521 Fax. +82-2-2632-5549
E-Mail : [email protected]
Downloaded from www.Manualslib.com manuals search engine