Engineered Solutions - AMC2 - Access Modular Controller

AMC2 - Access Modular Controller

u Intelligent access manager for one to eight

entrances

u A maximum of four interfaces include the reader

power supply

u Standard 2 GB Compact Flash

u LCD display for displaying information

u A maximum of eight input and output contacts

The AMC2 (Access Modular Controller) is used as an independent authorization on access points, takes
access controller in the access control systems: access decisions, controls closing/opening elements
• BISACE (Access Engine) from version 2.0 onward and registers movement events.
• AMS (Access Management System)
• APE (Access Professional Edition). System overview

The device controls a group of one to eight access 1

points. These access points, also known as entrances,
can be:
• doors
2 2 2 2
• gates
• barriers
• turn stiles
3 3
• revolving doors
• mantraps 4 4
• ID card, PIN and biometric readers 3 3
• door opening elements
• sensors.
1 Host computer 2 AMC2
The AMC2 can control a maximum of eight ID readers
(depending on the reader type) and fully processes 3 Card reader 4 Communication and power
the access logic at the assigned entrances. supply
The controller can be connected to the host system
The analog inputs have a status recognition of the through one of the following interfaces, depending on
connected lines. the type of installation:
With RS485 operation, a maximum of eight access
The relay outputs activate the door opening elements controllers can be connected to one party line.
and/or generate the security activation and signaling. The communication between the host system and the
controller via RS485 is encrypted with up to AES256,
The AMC2 stores all necessary information in a depending on the firmware version used.
battery-buffered memory and a compact flash storage In the communication chain of a system, the access
element. Thus, even when the unit is offline, it checks controller is integrated between the host system and
the peripheral devices.
 Engineered Solutions - AMC2 - Access Modular Controller 2|5

Functions • 4 and 7 for AC.

• 5 and 7 for battery.
• Storing downloaded data as listed below:
• 6 and 7 for DC.
– Master data Otherwise, these pins will short-circuit.
– Authorizations
– Access models Quantity restrictions
– Display texts • Follow the Access Engine installation and
configuration instructions regarding the maximum
– Reader configurations number of access controllers on one access control
• Interpretation of transaction data from reader: system.
– Authorization check • The maximum number of cards that a controller can
store is 400,000, depending on the access host
– Host request
system and the license used. For further
– PIN code information, refer to the datasheets of the BIS/ACE
• Control/monitoring: and AMS access control systems.
– Denial or door release
– Switching alarm Connections to the ID card readers

– Door statuses Wiegand interfaces

The AMC2 2WCF has two connections for connecting
– Reader operation statuses
a maximum of two ID card readers.
– Internal alarm statuses The AMC2 4WCF has four connections for connecting
• Messages to Access Engine: a maximum of four ID card readers.
The element interfaces of the ID card reader and the
– Host requests
door control are divided into groups, each with reader
– Transaction data for storing interface, two input and two output contacts.
– Error and malfunction messages The following definitions apply to the Wiegand
interfaces:
– Alarm messages
• 10-wire interface (including shield).
• Power supply for:
• Maximum cable length of 158 m (500 ft) to the ID
– Readers card reader.
– Door openers RS485 interfaces
– Contact current feeds The AMC2 4R4CF has four connections for connecting
a maximum of eight ID card readers, using secure
Regulatory information OSDPv2 protocol. The interfaces are divided into two
buses. A maximum of eight readers can be connected
Region Regulatory compliance/quality marks to one interface.
Countries of Eurasian EAC RS485 interface definition:
Customs Union • 2-wire interface: Using the 10-pin pluggable
connector.
Region Regulatory compliance/quality marks • Maximum length of the bus: 1200 m.
• Transfer rates: 9.6 kbit/s.
Poland CNBOP AMC2 4WCF

CNBOP AMC2 4R4CF Reader and door models

The AMC2 controls the connected reader through
USA UL UL 294; Refer to Ordering Information predefined door models.
Door models control in accordance with the relevant
FCC Part 15 Class B; Refer to Ordering security requirements:
Information • Number and usage of the readers connected to the
AMC2, such as input and output readers, input
Installation/configuration notes readers, buttons.
Power supply • Number and application type of the AMC inputs,
An external power supply (10 to 30 V DC) for the such as door status, output button, revolving door
AMC2 is connected to the pin 1 (positive) and 3 position.
(negative). When using an uninterruptible power • Number and usage of AMC outputs, such as door
supply (UPS), the relevant UPS output relay can be opener, mantrap contact, signal light switching.
connected to the pins:
Engineered Solutions - AMC2 - Access Modular Controller 3|5

The maximum number of entrances to be managed by Capacity

one AMC2 is ultimately defined by the door models
used and their requirements regarding readers and Number of analog inputs • AMC2-2WCF: 4
inputs/outputs. • AMC2-4WCF: 8
• AMC2-4R4CF: 8
Voltage equalization: grounding
• Potential differences can be compensated through Number of relay outputs • AMC2-2WCF: 4
the protective grounding with a jumper. • AMC2-4WCF: 8
• A line (shield, equipotential bonding line) with
• AMC2-4R4CF: 8
protective ground can only be connected in one
position.
Connectivity
• For further instructions, see the operating manual.
Host interface • RS485 (2- or 4- wire); opto-
Contacts decoupled
Inputs • Ethernet 10/100BaseT (TCP/IP)
The eight analog inputs can be used as digital or with RJ45
analog contacts. For analog use, resistance values can
be specified that make it possible to carry out a Reader interfaces • AMC2-2WCF: 2 Wiegand
further check for cable breaks and short-circuits. • AMC2-4WCF: 4 Wiegand
Relay outputs • AMC2-4R4CF: 4 RS485; 2-wire,
The relay outputs offer the following functions: opto-coupled, 9,600 Bd
• The outputs can operate with potential free
contacts for external power supply (dry mode). Electrical
• The outputs can operate using the internal voltage
of power supply (wet mode). Power supply 10 to 30 VDC, max. 60 VA
• Only ohm resistive loads can be connected to the Available for external devices: 55 VA
relay.
• Inductive loads must be bypassed through recovery Environmental
diodes. These diodes (1N4004) are enclosed.
Operating temperature (°C) 0 °C – 45 °C
General instructions
• AMC2 and related equipment should be mounted in Operating temperature (°F) 32 ºF - 113 ºF
a "secured area".
• Detailed connection conditions are specified in the IP rating IP30
operating manual.
• After purchase, primary AC power must be done by Mechanical
a licensed electrician.
Color White
Technical specifications

Hardware Dimension (H x W x D) (mm) 232 mm x 90 mm x 63 mm

Components and features • Integrated Microcontroller Dimension (H x W x D) (in) 9.13 in x 3.54 in x 2.48 in

• 512 kB-EPROM/FLASH Material Base: PPO (UL 94 V-0)

• 256 kB-SRAM Upper: Polycarbonate (UL 94 V-0)

• Serial EEPROM Mounting type Rail-mounted

• RTC
Weight (g) 503 g - 540 g
• Pluggable 2 GB Compact Flash
Weight (lb) 1.1 lb - 1.19 lb
• Battery for SRAM and RTC

• Reset button Operation

• Host address can be set via DIP
Protection Tamper switch
switch
Engineered Solutions - AMC2 - Access Modular Controller 4|5

Ordering information API-AMC2-16ION Standalone controller for BIS with

OPC
APC-AMC2-2WCF Door controller WI, 2 readers Standalone controller with inputs and outputs only.
Two Wiegand interfaces for up to 2 card readers, Compatible with BIS in combination with OPC Server
network connection to the host system and Compact only.
Flash memory (2 GB). Host data transfer encrypted. Order number API-AMC2-16ION | F.01U.013.384
F.01U.407.657: CE certification. F.01U.371.285: CE and
APS-PSU-60 Power supply unit
UL certification.
A power supply unit with an integrated battery charging
Order number APC-AMC2-2WCF | F.01U.407.657
device, that supports 12 V/7 Ah, 12 V/14 Ah and 24 V/7
F.01U.371.285
Ah batteries, with selectable 12 VDC or 24 VDC voltage
APC-AMC2-4WCF Door controller Wiegand with CF output.
card Order number APS-PSU-60 | F.01U.282.970
Four Wiegand interfaces for up to 4 card readers,
D126 Battery, 12V 7Ah
network connection to the host system and Compact
A rechargeable sealed lead‑acid power supply used as a
Flash memory (2 GB). Host data transfer encrypted.
secondary power supply or in auxiliary or ancillary
F.01U.407.651: CE certification. F.01U.027.201: CE and
functions.
UL certification.
Order number D126 | 4.998.125.825
Order number APC-AMC2-4WCF | F.01U.407.651
F.01U.027.201 AEC-AMC2-UL01 AMC enclosure with 1 DIN rail
Compliant with UL294 system certification for AMC2.
APC-AMC2-4R4CF Door controller RS485 with CF card
Order number AEC-AMC2-UL01 | F.01U.330.018
Four RS-485 interfaces for up to 8 card readers, network
connection to the host system and Compact Flash AEC-AMC2-UL02 AMC enclosure with 2 DIN rails
memory (2 GB). Host data transfer encrypted. Reader Compliant with UL294 system certification for AMC2.
data transfer encrypted according to reader capabilities. Order number AEC-AMC2-UL02 | F.01U.330.017
F.01U.407.653: CE certification. F.01U.027.206: CE and AEC-PANEL19-UPS Fitting panel, 19", 2 DIN rails
UL certification. Mounting plate with two DIN rails, a battery bracket, and
Order number APC-AMC2-4R4CF | F.01U.407.653 screw sockets for the power supply to mount into 19”
F.01U.027.206 racks.
Order number AEC-PANEL19-UPS | F.01U.066.193
Accessories
AEC-PANEL19-4DR Fitting panel, 19", 4 DIN rails
API-AMC2-4WE Door controller Wiegand extension
Mounting plate with four DIN rails for 19” racks to
The extension module AMC2 4W-EXT is equipped with
connect max. four AMC2 devices.
four Wiegand type reader-interfaces plus eight inputs
Order number AEC-PANEL19-4DR | F.01U.066.194
and eight outputs. Hence with the AMC2 4W-EXT it is
possible to double the number of readers on an AMC2 ACX-RAIL-400 DIN rail 400mm
4W from 4 to 8. F.01U.407.652: CE certification. Mounting rail (400 mm) for mounting the AMC2
F.01U.011.593: CE and UL certification. component (controller and PSU) when the metal housing
Order number API-AMC2-4WE | F.01U.407.652 is not used.
F.01U.011.593 Order number ACX-RAIL-400 | F.01U.510.954
API-AMC2-8IOE Extention board with 8-input 8-output ACX-RAIL-250 DIN rail 250mm
8 input/output extension board, up to three per AMC, Mounting rail (250 mm) for mounting the AMC2
can be combined with the AMC2 16I-EXT and the AMC2 component when the metal housing is not used.
16I-16O-EXT. F.01U.407.654: CE certification. Order number ACX-RAIL-250 | F.01U.510.935
F.01U.027.200: CE and UL certification.
Order number API-AMC2-8IOE | F.01U.407.654 Services
F.01U.027.200 EWE-AMCCTR-IW 12 mths wrty ext. AMC Reader
Controller
API-AMC2-16IOE Extention board with 16-input 16-
12 months warranty extension
output
Order number EWE-AMCCTR-IW | F.01U.364.824
16 input/output extension board, up to three per AMC,
can be combined with the AMC2 16I-EXT and the AMC2
8I-8O-EXT. F.01U.407.655: CE certification.
F.01U.013.385: CE and UL certification.
Order number API-AMC2-16IOE | F.01U.407.655
F.01U.013.385
API-AMC2-16IE Extention board with 16-input
16 input extension board, up to three per AMC, can be
combined with the AMC2 16I-16O-EXT and the AMC2
8I-8O-EXT. F.01U.407.656: CE certification.
F.01U.045.514: CE and UL certification.
Order number API-AMC2-16IE | F.01U.407.656
F.01U.045.514
 Engineered Solutions - AMC2 - Access Modular Controller 5|5

Represented by:

Europe, Middle East, Africa: Germany: North America: Asia-Pacific:

Bosch Security Systems B.V. Bosch Sicherheitssysteme GmbH Bosch Security Systems, LLC Robert Bosch (SEA) Pte Ltd, Security Systems
P.O. Box 80002 Robert-Bosch-Ring 5 130 Perinton Parkway 11 Bishan Street 21
5600 JB Eindhoven, The Netherlands 85630 Grasbrunn Fairport, New York, 14450, USA Singapore 573943
Phone: + 31 40 2577 284 Tel.: +49 (0)89 6290 0 Phone: +1 800 289 0096 Phone: +65 6571 2808
www.boschsecurity.com/xc/en/contact/ Fax:+49 (0)89 6290 1020 Fax: +1 585 223 9180 Fax: +65 6571 2699
www.boschsecurity.com [email protected] [email protected] www.boschsecurity.com/xc/en/contact/
www.boschsecurity.com www.boschsecurity.com www.boschsecurity.com

Data subject to change without notice | 202210171623 | V6 | October 17, 2022 © Bosch Security Systems 2022