UNIVERSAL PRODUCT LINE: Section 1401

CAST IRON — NON-JACKETED PUMPS Page 1401.1

124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
4124B Series™, 324A Series™, 1324A Series™, 4324A Series™ Issue F

TABLE OF CONTENTS SERIES DESCRIPTION

Related Products........................................................................1
124A Series™, 124AE Series™, 4124A Series™,
Operating Range.........................................................................1 4124AE Series™, 324A Series™, 4324A Series™:
Series Description.......................................................................1 The Universal Product Line has the broadest range of
Features & Benefits....................................................................2 sealing options of all pumps built by Viking. The stuffing box
on all sizes accepts packing, numerous component single
Port Location Options.................................................................2
mechanical seals, or a wide variety of cartridge seals.
Model Number Key.....................................................................2
The Universal Product Line is Viking Pump’s most versatile
Standard Materials of Construction............................................3 line of internal gear pumps due to the availability of many
Cutaway View & Pump Features (124A Series™, 124AE Series™, design and material options.
1124 Series™, 1124AE Series™, 4124A Series™, 4124AE Series™, 324A Series™,
1324A Series™, 4324A Series™).............................................................4 4124B Series™:
Cutaway View & Pump Features (4124B Series™)..........................5 The 4124B series heavy duty internal gear pumps have
Behind the Rotor dynamic shaft seals. By locating the
Special Materials & Options Selection Guidelines.....................6 mechanical seal immediately behind the rotor, this prevents
Specifications – G, H, HL, AK, AL, K, KK, L Sizes.....................7 the shaft and bracket bushing from coming into contact
with the liquid.
Specifications – LQ, LL, LS, Q, QS, M, N, R, RS Sizes.............8
Optional Casings.........................................................................9 1124A Series™, 1124AE Series™, 1324A Series™:
Dimensions – G, H, HL, AK, AL, K, KK, L, LQ, LL, LS, Q, M Viking Pump is the leader in internal gear innovation and the
Sizes..........................................................................................10 latest development is the O-Pro™ Seal technology. The NEW
Dimensions – G, H, HL, AK, AL, K, KK, L, LQ, LL, LS, Q, M Universal Seal Product Line comes with the O-Pro Barrier
Sizes (Cont'd)............................................................................... 11 Seal factory installed. The Universal Product Line combines
the tested reliability of the Universal pump & O-rings to create
Dimensions – QS Size..............................................................12 a robust seal and lubrication chamber, all in one.
Dimensions – N, R, RS Sizes – Jacketed Bracket
(324A Series™, 1324A Series™, 4324A Series™)........................................13
Dimensions – Stuffing Box Seal Chamber (Except 4124B Series™).14
NPSH Required........................................................................15

RELATED PRODUCTS
L124A K4124B
Cast Iron, Jacketed Pumps: Catalog Section 1402
Cast Iron, Mag Drive Pumps: Catalog Section 1403
Steel Externals, Non-Jacketed Pumps: Catalog Section 1301
Stainless Steel, Non-Jacketed Pumps: Catalog Section 1701 KK1124A

OPERATING RANGE
NOMINAL FLOW MAXIMUM PRESSURE TEMPERATURE RANGE VISCOSITY RANGE
SERIES GPM m3 h PSI Bar °F °C SSU cSt
124A Series™
8 - 500 1.8 - 114 200 14 −60 to +450 −50 to +230 28 to 2,000,000 0.1 to 440,000
124AE Series™ **
1124A Series™
8 - 400 1.8 - 91 200 14 0 to +225* −15 to +105* 100 to 2,500* 20 to 550*
1124AE Series™ **
4124A Series™
8 - 500 1.8 - 114 200 14 −60 to +450 −50 to +230 28 to 2,000,000 0.1 to 440,000
4124AE Series™ **
4124B Series™ 8 - 500 1.8 - 114 200 14 −60 to +450 −50 to +230 28 to 15,000 0.1 to 3,300
324A Series™ 600 - 1,600 136 - 364 200 14 −60 to +450 −50 to +230 28 to 2,000,000 0.1 to 440,000
1324A Series™ 500 - 1,300 136 - 295 200 14 0 to +225* −15 to +105* 100 to 750* 20 to 165*
4324A Series™ 600 - 1,600 136 - 364 200 14 −60 to +450 −50 to +230 28 to 2,000,000 0.1 to 440,000
* Range may increase with end clearance adjustment. ** AE available in sizes L, LQ, LL only.

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

 Section 1401 UNIVERSAL PRODUCT LINE:
Page 1401.2 CAST IRON — NON-JACKETED PUMPS
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
Issue F 4124B Series™, 324A Series™, 1324A Series™, 4324A Series™

FEATURES & BENEFITS

• Positive Displacement Internal Gear pumping principle
handles a broad range of viscosities with constant flow rate
• Axial rotor thrust is controlled by double row ball bearing
or tapered roller bearings; a bushing provides a secondary
point of radial shaft support
For warranty details, please go to:
• Rotatable bearing housing provides easy rotor end
vikingpump.com/warranty#information
clearance adjustment for viscosity or to compensate wear
• Numerous material options are available for bushings, idler
pins, shafts, rotors, idlers and elastomers
124A Series™, 124AE Series™, 1124A Series™,
1124AE Series™, 4124A Series™, 4124AE Series™,
• Gear and pump geometry has been optimized based on
more than 100 years of experience
324A Series™, 1324A Series™, 4324A Series™ Only:
• Series designed with an enlarged bearing housing. Used in
• Footed cast iron bracket provides rigid mounting to help
conjunction with a spacer coupling permits easy cartridge
maintain alignment, which extends seal and bearing life
seal or O-Pro™ Barrier Seal installation and removal in
• Can use direct drive, gear reducer or gearmotor drive, place without removing the head and rotor/shaft.
or belt-drive
• Seal options include packing, O-Pro™ Barrier Seal, single
• Pressure relief valve standard on all except RS size component seals, cartridge lip seals and cartridge single
pumps; less valve / plain head option available and double mechanical seals. Various seal flush plans are
available.

PORT LOCATION OPTIONS

90° Port Options: Opposite Port Options:

NOTE: See page 1401.9 for a complete list of casing options by size.

MODEL NUMBER KEY

L Q 4 1 2 4 A E
Size: Basic Series Material of Primary Shaft Diameter
G LL Configuration Construction: (L, LQ and LL Sizes in Cast Iron Only):
H LS 4 = Cast Iron
Jacketing: Blank = 1-7/16"
HL Q E = 1-5/8"
1 = No Jacketing
AK QS (See dimension drawings for shaft diameter at coupling)
3* = Foot Mount Casing w/ Jacketed Bracket
AL M
K N Shaft Seal: Seal Location:

KK R 4 = Mechanical Seal A = Stuffing Box Seal

L RS 1 = O-Pro™ Seal B = Behind the Rotor

LQ Blank = Packing
* Note: Only the N, R & RS sizes are foot mount casing with jacketed bracket.

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

UNIVERSAL PRODUCT LINE: Section 1401
CAST IRON — NON-JACKETED PUMPS Page 1401.3
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
4124B Series™, 324A Series™, 1324A Series™, 4324A Series™ Issue F

STANDARD MATERIALS OF CONSTRUCTION

Component Standard Material

Casing Cast Iron, ASTM A48, Class 35B
Head Cast Iron, ASTM A48, Class 35B
Bracket Cast Iron, ASTM A48, Class 35B
Standard ① Cast Iron, ASTM A48, Class 35B
Idler
Steel Fitted ①② Cast Iron, ASTM A48, Class 35B
Standard ③ Cast Iron, ASTM A48, Class 35B
Rotor
Steel Fitted ④ Steel, ASTM A148, Grade 80-40
Shaft ⑤ Steel, ASTM A108, Grade 1045
Idler Pin Hardened Steel, ASTM A108, Grade 1045
(4124A Series™, 4124AE Series™,
Carbon Graphite
4324A Series™, 4124B Series™)
(1124A Series™, 1124AE Series™,
Idler Bushing Hardened Cast Iron
1324A Series™)
(124A Series™, 124AE Series™, Bronze, ASTM B584 (B505),
324A Series™) Alloy C93700
(4124A Series™, 4124AE Series™,
Carbon Graphite
Bracket Bushing (no product contact on 4124B Series™) 4324A Series™)
(Note: not applicable on 1124A Series™, 1124AE Series™ or 1324A Series™) (124A Series™, 124AE Series™, Bronze, ASTM B584 (B505),
324A Series™, 4124B Series™) Alloy C93700
Pressure Relief Valve ⑥ Cast Iron, ASTM A48, Class 35B
Standard Packing (124A Series™, 124AE Series™, 324A Series™) Braided PTFE
O-Pro™ Barrier Seal (1124A Series™, 1124AE Series™ or 1324A Series™) Hardened Cast Iron, Sanitary FKM Elastomers
Standard Mechanical Seal (4124A Series™, 4124AE Series™,
Carbon vs. Silicon Carbide Faces, FKM Elastomers
4124B Series™, 4324A Series™)
Optional Abrasive Liquid Seal (4124B Series™) Silicon Carbide vs. Silicon Carbide Faces, FKM Elastomers

① G, H and HL sizes have a powdered metal idler: Powdered Metal MPIF 35, FC-0208-45 (G) , Powdered Metal MPIF 35, FC-0208-50 (H, HL)
② Q and QS sizes have a hardened steel idler when pump is steel fitted: ASTM A148 Grade 80-40.
③ AK, KK, LS, QS, N and RS sizes have ductile iron rotor: ASTM A536 Grade 60-40-18.
④ Material specification for HL steel rotor is AISI 8620, LS steel rotor is ASTM A148 80-50.
⑤ AK, AL, K, KK, L, LQ, LL and LS sizes, including “A”, “AE”, and “B” models, are high strength steel ASTM A434 Type 4140 Grade BC or equivalent.
⑥ RS relief valve not available. Contact factory for options.

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

Section 1401 UNIVERSAL PRODUCT LINE:
Page 1401.4 CAST IRON — NON-JACKETED PUMPS
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
Issue F 4124B Series™, 324A Series™, 1324A Series™, 4324A Series™

CUTAWAY VIEW & PUMP FEATURES (124A SERIES™, 124AE SERIES™,

1124 SERIES™, 1124AE SERIES™, 4124A SERIES™, 4124AE SERIES™,
324A SERIES™, 1324A SERIES™, 4324A SERIES™)
Packing O-Pro™ Barrier Seal Component Seal Cartridge Seal

Seal chamber accepts Multiple port sizes, types,

packing, O-Pro™ seal and and ratings are available
a variety of component and including threaded or flanged
Large diameter cartridge style mechanical (Class 125, Class 250)
threaded bearing and lip seals, in both single
housing allows and double mechanical
easy seal removal seal configurations

Double row ball

bearing or tapered
roller bearings for
axial thrust control

One-piece cast
bracket with seal
between bearings
provides rigid
foundation to
maximize seal
and bearing life
Rotor end clearance can be adjusted Internal relief valve standard*;
to compensate for wear or for higher less valve / plain head and return-
temperatures or viscosities by rotating to-tank relief valves optional
the threaded bearing housing

* All except RS size

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

UNIVERSAL PRODUCT LINE: Section 1401
CAST IRON — NON-JACKETED PUMPS Page 1401.5
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
4124B Series™, 324A Series™, 1324A Series™, 4324A Series™ Issue F

CUTAWAY VIEW & PUMP FEATURES (4124B SERIES™)

Multiple porting sizes, types,

and ratings are available
including threaded or flanged
Bracket bushing (Class 125, Class 250)
never contacts
pumped liquid,
Lip seal keeps ensuring
grease in bracket long life
Grease fitting
for bushing
with relief fitting
lubrication
on opposite side

Internal pressure
relief valve standard,
protects pump from
overpressure; less
valve / plain head and
return-to-tank relief
Threaded bearing housing valves optional
enables fast, easy end clearance
adjustment for viscosity or wear
Behind the rotor seal
Rigid cast iron mounting bracket protects bracket bushing
helps ensure alignment and minimizes effects of from wear or corrosion
pipe strain for the longest seal and bearing life

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

 Section 1401 UNIVERSAL PRODUCT LINE:
Page 1401.6 CAST IRON — NON-JACKETED PUMPS
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
Issue F 4124B Series™, 324A Series™, 1324A Series™, 4324A Series™

SPECIAL MATERIALS & OPTIONS SELECTION GUIDELINES

For High Viscosities – Above 2,500 SSU (550 cSt)
• Steel fitted construction recommended above the following viscosities, according to pump size:

Pump Size
Viscosity
G H HL AK AL K KK L LQ LL LS Q QS M N R RS
SSU 7,500 25,000 7,500 25,000 25,000 25,000 75,000 25,000 25,000 2,500 75,000 7,500 75,000 25,000 75,000 25,000 75,000
cSt 1,700 5,500 1,700 5,500 5,500 5,500 17,000 5,500 5,500 550 17,000 1,700 17,000 5,500 17,000 5,500 17,000

• Extra clearances, depending on viscosity. See ES-2 for recommendations.

» 1124A Series™, 1124AE Series™ & 1324A Series™ pumps only available with standard clearance.
• Special Sealing:
FKM or Buna N Type 1 component seals good up to 15,000 SSU (3,300 cSt).
PTFE Type 9 seals good up to 25,000 SSU (5,500 cSt).
Packed gland good up to 2,000,000 SSU (440,000 cSt).
Cartridge triple lip seals available to 2,000,000 SSU (440,000 cSt).
• Larger ports may be required depending on suction conditions.
• Pump should be operated at slower than normal speeds, which may require a larger pump.
• For viscosities over 250,000 SSU (55,000 cSt), contact factory for additional pump construction and operation
recommendations.

For low viscosities or non-lubricating liquids – Below 100 SSU (20 cSt)
• Carbon graphite bushings.
• Pump should be operated at slower than normal speeds, which may require a larger pump.

For high temperatures – Above 225°F (105°C)

• High temperature elastomers – FKM up to 350°F (175°C); Buna up to 225°F (105°C); PTFE up to 450°F (230°C);
• High temperature bushings recommended depending on temperature, size and specific material.
See ESB-3 for recommendations.
• Additional operating clearances may be required depending on temperature, size and specific material.
See ES-2 for recommendations.
» 1124A Series™, 1124AE Series™ & 1324A Series™ pumps only available with standard clearance.
• For temperatures above 450°F (230°C), special materials and sealing requirements may be needed.
Contact factory for recommendations.
• Pump should be operated at slower than normal speeds, which may require a larger pump.

For abrasive or dirty liquids

• If possible, filter or strain out the abrasives present.
• Wear resistant bushings - hardened cast iron, tungsten carbide or Colmonoy coated.
• Abrasive-resistant idler pin - tungsten carbide or Colmonoy plus TC filler coated pins.
• Hardened or hard-coated shaft.
• Abrasive-resistant seals.
• For high concentrations of abrasives or particle sizes greater than 250 microns (0.010 in), contact factory for recommendations.
• Pump should be operated at slower than normal speeds, which may require a larger pump.
• Consult factory for specific recommendations.

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

UNIVERSAL PRODUCT LINE: Section 1401
CAST IRON — NON-JACKETED PUMPS Page 1401.7
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
4124B Series™, 324A Series™, 1324A Series™, 4324A Series™ Issue F

SPECIFICATIONS – G, H, HL, AK, AL, K, KK, L SIZES

③ ② Maximum
Standard ④ Maximum ① Recommended
NPT Nominal Pump Rating Hydrostatic Maximum Discharge Temperature for Approx. Shipping
Port Size (100 SSU & below) Pressure Pressure Standard Pump Weight with Valve
Model
Number Inches GPM m3/h RPM PSIG BAR PSIG BAR °F °C Lbs. Kg.
G124A 1 8 1.8 1750 400 28 200 14 450 230 25 11
G4124A 1 8 1.8 1750 400 28 200 14 350 175 25 11
G4124B 1 8 1.8 1750 400 28 200 14 350 175 22 10
H124A 1½ 15 3.5 1750 400 28 200 14 450 230 38 17
H1124A 1½ 8 1.8 1000 400 28 200 14 225 105 40 18
H4124A 1½ 15 3.5 1750 400 28 200 14 350 175 38 17
H4124B 1½ 15 3.5 1750 400 28 200 14 350 175 38 17
HL124A 1½ 30 7 1750 400 28 200 14 450 230 40 18
HL1124A 1½ 18 4 1000 400 28 200 14 225 105 40 18
HL4124A 1½ 30 7 1750 400 28 200 14 350 175 40 18
HL4124B 1½ 30 7 1750 400 28 200 14 350 175 40 18
AK124A 2 65 15 1450 400 28 200 14 450 230 82 37
AK4124A 2 65 15 1450 400 28 200 14 350 175 82 37
AK4124B 2 65 15 1450 400 28 200 14 350 175 78 35
AL124A 2 90 20 1450 400 28 200 14 450 230 85 39
AL4124A 2 90 20 1450 400 28 200 14 350 175 85 39
K124A 2 80 18 780 400 28 200 14 450 230 105 48
K1124A 2 80 18 780 400 28 200 14 225 105 110 50
K4124A 2 80 18 780 400 28 200 14 350 175 105 48
K4124B 2 80 18 780 400 28 200 14 350 175 105 48
KK124A 2 100 23 780 400 28 200 14 450 230 110 50
KK1124A 2 100 23 780 400 28 200 14 225 105 110 50
KK4124A 2 100 23 780 400 28 200 14 350 175 110 50
KK4124B 2 100 23 780 400 28 200 14 350 175 110 50
L124A 2 135 31 640 400 28 200 14 450 230 155 70
L124AE 2 135 31 640 400 28 200 14 450 230 155 70
L1124AE 2 135 31 640 400 28 200 14 225 105 147 67
L4124A 2 135 31 640 400 28 200 14 350 175 155 70
L4124AE 2 135 31 640 400 28 200 14 350 175 155 70
L4124B 2 135 31 640 400 28 200 14 350 175 155 70

① For maximum recommended discharge pressures at different ③ Ports are tapped for standard (NPT) pipe. Other thread standards
viscosities, see performance curves, which can be electronically available. G through L ports are at 90°.
generated with the Viking Pump Curve Generator, located on ④ Maximum hydrostatic pressure for standard pump construction.
www.vikingpump.com. If suction pressure exceeds 50 PSIG, Rating is dependent on seal, gaskets and ports.
consult factory. Higher pressures possible with factory approval
based on application details.
② Extra clearances are required above 225°F / 105°C.
Higher temperatures can be handled with special construction,
consult factory.

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

 Section 1401 UNIVERSAL PRODUCT LINE:
Page 1401.8 CAST IRON — NON-JACKETED PUMPS
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
Issue F 4124B Series™, 324A Series™, 1324A Series™, 4324A Series™

SPECIFICATIONS – LQ, LL, LS, Q, QS, M, N, R, RS SIZES

① Maximum ② Maximum
③ ④ Maximum Discharge Pressure Recommended
Standard Nominal Pump Rating Hydrostatic for 100 SSU liquid Temperature for Approx. Shipping
Port Size (100 SSU & below) Pressure at rated speed Standard Pump Weight with Valve
Model
Number Inches GPM m3/h RPM PSIG BAR PSIG BAR °F °C Lbs. Kg.
LQ124A 2½ 135 31 640 300 21 200 14 450 232 175 80
LQ124AE 2½ 135 31 640 300 21 200 14 450 232 175 80
LQ1124AE 2½ 120 27 520 400 28 200 14 225 110 191 87
LQ4124A 2½ 135 31 640 300 21 200 14 350 175 175 80
LQ4124AE 2½ 135 31 640 300 21 200 14 350 175 175 80
LQ4124B 2½ 135 31 640 300 21 200 14 350 175 175 80
LL124A 3 140 32 520 300 21 200 14 450 232 185 84
LL124AE 3 140 32 520 300 21 200 14 450 232 185 84
LL1124AE 3 140 32 640 400 28 200 14 225 110 199 90
LL4124A 3 140 32 520 300 21 200 14 350 175 185 84
LL4124AE 3 140 32 520 300 21 200 14 350 175 185 84
LL4124B 3 140 32 520 300 21 200 14 350 175 185 84
LS124A 3 200 45 640 300 21 200 14 450 232 190 86
LS1124A 3 200 45 640 400 28 200 14 225 110 228 103
LS4124A 3 200 45 640 300 21 200 14 350 175 190 86
LS4124B 3 200 45 640 300 21 200 14 350 175 190 86
Q124A 4 300 68 520 250 17 200 14 450 232 440 200
Q1124A 4 275 62 470 250 17 200 14 225 110 472 214
Q4124A 4 300 68 520 250 17 200 14 350 175 440 200
Q4124B 4 300 68 520 250 17 200 14 350 175 440 200
QS124A 6 500 114 520 250 17 200 14 450 232 540 245
QS1124A 6 400 91 470 250 17 200 14 225 110 507 230
QS4124A 6 500 114 520 250 17 200 14 350 175 540 245
QS4124B 6 500 114 520 250 17 200 14 350 175 540 245
M124A 4 420 95 420 250 17 200 14 450 232 600 272
M4124A 4 420 95 420 250 17 200 14 350 175 600 272
N324A 6 600 136 350 250 17 200 14 450 232 810 367
N1324A 6 535 122 330 250 17 200 14 225 110 937 425
N4324A 6 600 136 350 250 17 200 14 350 175 810 367
R324A 8 1100 250 280 250 17 200 14 450 232 1435 651
R1324A 8 915 208 225 250 17 200 14 225 110 1523 961
R4324A 8 1100 250 280 250 17 200 14 350 175 1435 651
RS324A 10 1600 364 280 250 17 125 8.5 450 232 2000 907
RS1324A 10 1300 295 255 250 17 125 8.5 225 110 1973 895
RS4324A 10 1600 364 280 250 17 125 8.5 350 175 2000 907

① For maximum recommended discharge pressures at different ③ Flange ports are suitable for use with Class 125 ANSI cast iron
viscosities, see performance curves, which can be electronically companion flanges or flanged fittings.
generated with the Viking Pump Curve Generator, located on LQ, LL, LS, Q & M ports are at 90°
www.vikingpump.com. If suction pressure exceeds 50 PSIG, QS, N, R and RS ports are at 180° (opposite)
consult factory. Higher pressures possible with factory approval ④ Maximum hydrostatic pressure for standard pump construction.
based on application details. Rating is dependent on seal, gaskets and ports.
② Extra clearances are required above 225°F / 105°C.
Higher temperatures can be handled with special construction,
consult factory.

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

UNIVERSAL PRODUCT LINE: Section 1401
CAST IRON — NON-JACKETED PUMPS Page 1401.9
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
4124B Series™, 324A Series™, 1324A Series™, 4324A Series™ Issue F

OPTIONAL CASINGS

Standard Casings
Ports
Size (Inches) Rotatable Data Optional Casings
G 1.5”①Ⓡ Fully Rotatable 1.5”②Ⓡ 1.5”③Ⓡ 2”②Ⓡ
H 1.5”①Ⓡ Fully Rotatable 1.5”②Ⓡ 1.5”③Ⓡ 2”②Ⓡ
HL 1.5”①Ⓡ Fully Rotatable 1.5”②Ⓡ 1.5”③Ⓡ 2”②Ⓡ
AK 2”①Ⓡ Fully Rotatable
AL 2”①Ⓡ Fully Rotatable
K 2”①Ⓡ Fully Rotatable 2”②Ⓡ 2”③Ⓡ 2.5”①Ⓞ 2.5”②Ⓡ 3”②Ⓡ 4”②Ⓡ
KK 2”①Ⓡ Fully Rotatable 2”②Ⓡ 2”③Ⓡ 2.5”①Ⓞ 2.5”②Ⓡ 3”②Ⓡ 4”②Ⓡ
L 2”①Ⓡ Fully Rotatable
Side 5”②Ⓡ,
LQ 2.5”②Ⓡ Ports cannot face down 2.5”③Ⓡ 3”②Ⓡ 4”②Ⓡ 6”②Ⓡ*
Top 6”②
LL 3”②Ⓡ Fully Rotatable 3”③Ⓡ 4” ②Ⓡ 5”②Ⓡ*
LS 3”②Ⓡ Fully Rotatable 3”③Ⓡ 4” ②Ⓡ*
Side 4” ②Ⓡ, Side 4” ②Ⓛ, Side 6” ②Ⓡ,
Q 4”②Ⓡ Fully Rotatable 4”③Ⓡ 3”②Ⓡ 5”②Ⓡ 6”②Ⓞ
Top 8” ② Top 8” ② Top 8” ②
QS 6”②Ⓞ Rotatable with special casing 6”②Ⓡ
M 4”②Ⓡ Fully Rotatable 6”②Ⓡ 6”②Ⓞ
N 6”②Ⓞ Not Rotatable 5”②Ⓝ 6”②Ⓝ
R 8”②Ⓞ Not Rotatable 6”②Ⓝ
RS 10”②Ⓞ Not Rotatable 10”②

① Port(s) tapped for standard (NPT) pipe. Ⓛ 90° port arranged for Left Hand inlet (viewed from shaft end)
② Port(s) suitable for use with Class 125 ANSI cast iron companion Ⓝ Non-Rotatable Ports at 90° angle, contact factory for available
flanges or flanged fittings. orientation (right hand or left hand)
③ Port(s) suitable for use with Class 250 ANSI cast iron companion Ⓞ Opposite Ports
flanges or flanged fittings. Ⓡ 90° port arranged for Right Hand inlet (viewed from shaft end)
* Core smaller than port size

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

 Section 1401 UNIVERSAL PRODUCT LINE:
Page 1401.10 CAST IRON — NON-JACKETED PUMPS
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
Issue F 4124B Series™, 324A Series™, 1324A Series™, 4324A Series™

DIMENSIONS – G, H, HL, AK, AL, K, KK, L, LQ, LL, LS, Q, M SIZES

S W
B A
T R N
K

U
C

V D

P J O
F E E
M H L G

These dimensions are average and not for construction purposes. Certified prints on request. NOTE: Dimensions “N” through “W” on next page

Model Number
Mechanical A
Packed O-Pro™ Seal Seal (in) B C D E F G H J K L M
G4124A in 2.50 3.66 2.75 1.62 1.31 4.00 2.38 0.34 0.57 1.21 4.87
G124A ①1
G4124B mm 64 93 70 41 33 102 60 9 14 31 124
H4124A
in 3.00 4.75 3.50 2.75 2.25 6.75 3.50 0.47 0.99 3.38 5.19
H124A H1124A H4124B
① 1.5
HL124A HL1124A HL4124A
mm 76 121 89 70 57 171 89 12 25 86 132
HL4124B
AK4124A in 4.50 6.75 5.25 2.88 2.00 6.75 4.03 0.41 1.67 2.82 8.84
AK124A
AL4124A ①2
AL124A
AK4124B mm 114 171 133 73 51 171 102 10 42 72 225
K4124A
in 5.12 8.00 5.50 4.00 2.75 9.25 4.00 0.53 1.42 3.00 9.38
K124A K1124A K4124B
①2
KK124A KK1124A KK4124A
mm 130 203 140 102 70 235 102 13 36 76 238
KK4124B
L124A L4124A/AE in 6.50 10.25 7.00 4.38 4.00 10.00 5.38 0.53 1.42 ④ 3.38 9.12
L1124AE ①2
L124AE L4124B mm 165 260 178 111 102 254 137 13 36 ④ 86 232

LQ124A LQ4124A/AE in 7.19 10.25 7.00 4.38 4.00 10.00 5.38 0.53 1.42 ④ 3.38 9.12
LQ1124AE ② 2.5
LQ124AE LQ4124B mm 183 260 178 111 102 254 137 13 36 ④ 86 232

LL124A LL4124A/AE in 7.19 10.25 7.00 4.38 4.00 10.00 5.38 0.53 1.42 ④ 3.38 9.12
LL1124AE ②3
LL124AE LL4124B mm 183 260 178 111 102 254 137 13 36 ④ 86 232
LS4124A in 7.19 10.25 7.00 4.38 4.00 10.00 5.38 0.53 2.55 4.75 9.12
LS124A LS1124A ②3
LS4124B mm 183 260 178 111 102 254 137 13 65 121 232
Q4124A in 8.25 14.00 8.75 4.12 4.00 10.00 6.00 0.69 3.58 6.62 11.12
Q124A Q1124A ②4
Q4124B mm 210 356 222 105 102 254 152 18 91 168 282
in 9.50 17.35 10.00 5.00 6.00 12.00 8.53 0.69 3.50 7.75 8.10
M124A M4124A ②4
mm 241 441 254 127 152 305 217 18 89 197 206

① Ports are tapped for standard (NPT) pipe. Other thread standards available.
② Ports are suitable for use with Class 125 ANSI cast iron.
③ Ports are suitable for Class 150 ANSI steel or stainless steel companion flanges or flanged fittings.
④ “K” dimension for L, LQ & LL sizes is for “A” and “B” models. “K” dimension for L, LQ & LL size “AE” models is 1.30” (33.0 mm).

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

UNIVERSAL PRODUCT LINE: Section 1401
CAST IRON — NON-JACKETED PUMPS Page 1401.11
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
4124B Series™, 324A Series™, 1324A Series™, 4324A Series™ Issue F

DIMENSIONS – G, H, HL, AK, AL, K, KK, L, LQ, LL, LS, Q, M SIZES (CONT'D)
S W
B A
T R N
K

U
C

V D

P J O
F E E
M H L G

These dimensions are average and not for construction purposes. Certified prints on request. NOTE: Dimensions “A” through “M” on previous page

Model Number
Mechanical U V
Packed O-Pro™ Seal Seal N O P R S T (in) (in) W
G4124A in 1.09 0.31 0.63 7.40 9.55 1.06 2.71
G124A 0.50 .12 x .06
G4124B mm 28 8 16 188 143 27 69
H4124A
in 1.19 0.56 0.62 10.44 13.25 1.62 2.85
H124A H1124A H4124B
0.75 .19 x .09
HL124A HL1124A HL4124A
mm 30 14 16 265 337 41 72
HL4124B
AK4124A in 2.00 0.44 1.00 13.19 17.69 2.50 4.83
AK124A
AL4124A 1.00 .25 x .12
AL124A mm 51 11 25 335 449 64 123
AK4124B
K4124A
in 1.75 0.62 0.62 14.12 18.12 2.25 5.25
K124A K1124A K4124B
1.12 .25 x .12
KK124A KK1124A KK4124A
mm 44 16 16 359 460 57 133
KK4124B
in 1.75 0.62 0.62 15.62 19.62 2.25 5.43
L124A L4124A 1.12 .25 x .12
mm 44 16 16 397 498 57 138
L4124AE in 1.75 0.62 0.62 15.62 19.62 2.35 5.43
L124AE L1124AE 1.44 .38 x .19
L4124B mm 44 16 16 397 498 60 138
in 1.75 0.62 0.62 15.62 19.62 2.25 5.43
LQ124A LQ4124A 1.12 .25 x .12
mm 44 16 16 397 498 57 138
LQ4124AE in 1.75 0.62 0.62 15.62 19.62 2.35 5.43
LQ124AE LQ1124AE 1.44 .38 x .19
LQ4124B mm 44 16 16 397 498 60 138
in 2.25 0.62 0.62 15.62 20.12 2.25 5.43
LL124A LL4124A 1.12 .25 x .12
mm 57 16 16 397 511 57 138
LL4124AE in 2.25 0.62 0.62 15.62 20.12 2.35 5.43
LL124AE LL1124AE 1.44 .38 x .19
LL4124B mm 57 16 16 397 511 60 138
LS4124A in 2.44 0.62 0.62 15.75 21.69 3.50 5.43
LS124A LS1124A 1.44 .38 x .19
LS4124B mm 62 16 16 400 551 89 138
Q4124A in 3.00 0.8 1.00 19.25 26.75 4.50 8.25
Q124A Q1124A 1.94 .50 x .25
Q4124B mm 76 20 25 489 679 114 210
in 4.00 1.00 1.52 20.13 28.38 4.25 8.61
M124A M4124A 1.94 .50 x .25
mm 102 25 39 511 721 108 219

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

 Section 1401 UNIVERSAL PRODUCT LINE:
Page 1401.12 CAST IRON — NON-JACKETED PUMPS
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
Issue F 4124B Series™, 324A Series™, 1324A Series™, 4324A Series™

DIMENSIONS – QS SIZE
Dimensions shown in inches with millimeter equivalent shown in parentheses

28.25
718
19.75
502
4.50 4.00 8.29 9.00 9.00
114 102 211 229 229
4.37
111

2X 3.00
76

1.94 8.75
FLANGE*
222
.50 X .25
KEYWAY

1.00 Foot Bolt Hole 4X .69 .81

4.00 25 4.12
105 21
102
.88
11.13 6.00 7.12 4.12
22
283 152 181 105
10.00
254

* 124A Series™, 1124A Series™, 4124A Series™ ports suitable for use with Class 125 ANSI cast iron companion flanges or flanged fittings.
NOTE: Flanges are 6", suitable for use with Class 125 ANSI cast iron companion flanges or flanged fittings. They are studded, not through-bolt.

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

UNIVERSAL PRODUCT LINE: Section 1401
CAST IRON — NON-JACKETED PUMPS Page 1401.13
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
4124B Series™, 324A Series™, 1324A Series™, 4324A Series™ Issue F

DIMENSIONS – N, R, RS SIZES – JACKETED BRACKET

(324A SERIES™, 1324A SERIES™, 4324A SERIES™)

NPT X 4

Model Number
Stuffing A
Packed O-Pro™ Seal Box Seal (in) B C D E F G H J K M N
① in 9.75 17.25 9.50 5.00 6.25 8.69 1.62 0.69 4.50 12.00 4.50
N324A N1324A N4324A
6 mm 248 438 241 127 159 221 41 18 114 305 114

① in 14.25 24.50 13.25 6.75 7.00 10.56 2.31 0.78 6.00 16.00 5.62
R324A R1324A R4324A
8 mm 362 622 337 171 178 268 59 20 152 406 143

① in 14.25 24.5 13.25 6.75 7.00 13.12 4.81 0.88 6.00 16.46 8.12
RS324A RS1324A RS4324A
10 mm 362 622 337 171 178 333 122 22 152 418 206

Model Number
Stuffing
Packed O-Pro™ Seal Box Seal O P R S T U (in) V (in) W X Y Z
in 1.00 3.00 26.00 36.50 6.00 8.63 0.69 — 18.94
N324A N1324A N4324A 2.44 .62 x.31
mm 25 76 660 927 152 219 18 — 481
in 1.00 4.50 28.75 41.00 6.62 12.00 0.69 1.25 19.25
R324A R1324A R4324A 3.44 .88 x.44
mm 25 114 730 1041 168 305 18 32 489
in 1.30 4.50 28.55 43.49 6.62 — 0.88 1.25 19.25
RS324A RS1324A RS4324A 3.44 .88 x.44
mm 33 114 725 1105 168 — 22 32 489

① Ports are suitable for use with Class 125 ANSI cast iron (324A Series™/4324A Series™)
NOTE: The N size is standard with a jacketed bracket and non-jacketed head and non-jacketed relief valve, while the “R” size
is standard with a jacketed bracket, a jacketed head, and a non-jacketed relief valve. “RS” contact factory for jacketing options.
RS relief valve not available. Contact factory for options.

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

 Section 1401 UNIVERSAL PRODUCT LINE:
Page 1401.14 CAST IRON — NON-JACKETED PUMPS
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
Issue F 4124B Series™, 324A Series™, 1324A Series™, 4324A Series™

DIMENSIONS – STUFFING BOX SEAL CHAMBER

(EXCEPT 4124B SERIES™)

Pump Size A B C D E F G H J K L M N O P R
In 1.63 2.12 1.91 1.38 0.57 1.72 3.87 2.74 to 3.12 1.64 2.24 3.62 1.00 3.87 1/8
G 0.75 5/16
mm 41 54 49 38 15 44 98 70 to 79 42 57 92 25 98 3
In 2.00 2.41 2.22 1.90 1.03 2.27 4.50 3.00 to 3.50 2.00 2.50 4.00 0.66 4.47 1/8
H & HL 1.12 5/16
mm 51 61 56 48 26 58 114 76 to 89 51 64 102 17 114 3
In 2.31 2.69 2.75 2.25 1.24 3.03 5.25 3.14 to 4.56 2.50 3.00 5.00 0.47 6.15 1/4
AK & AL 1.44 7/16
mm 59 68 70 57 32 77 133 80 to 116 64 76 127 12 156 6
In ①2.31 3.00 3.13 2.25 1.25 3.00 5.25 3.50 to 4.50 2.50 3.00 5.00 0.38 5.25 1/4
K & KK 1.44 7/16
mm ①58.7 76 80 57 32 76 133 89 to 114 64 76 127 10 133 6
In ①2.31 3.00 3.13 2.25 1.25 4.00 5.25 3.50 to 4.50 2.50 3.00 5.00 0.44 5.25 1/4
L, LQ, & LL (A) 1.44 7/16
mm ①58.7 76 80 57 32 102 133 89 to 114 64 76 127 11 133 6
In 2.38 3.00 3.13 2.25 1.16 3.52 5.25 3.50 to 4.50 3.00 3.00 5.00 0.46 5.25 1/4
L, LQ, & LL (AE) 1.62 7/16
mm 60 76 80 57 30 89 133 89 to 114 76 76 127 12 133 6
In 2.38 2.80 2.70 2.25 1.16 3.52 5.25 3.25 to 4.50 3.00 2.80 5.00 0.46 5.25 1/4
LS 1.62 7/16
mm 60 71 69 57 30 89 133 83 to 114 76 71 127 12 133 6
In 3.42 4.50 4.00 2.50 1.53 4.10 6.75 5.50 to 6.25 3.20 4.50 7.20 0.56 6.75 1/4
Q & QS ③ 2.44 5/8
mm 87 114 102 64 39 104 171 140 to 159 81 114 183 14 171 6
In 3.44 — 3.97 2.50 1.53 4.16 6.75 5.44 to 6.26 3.28 4.50 7.20 0.72 7.37 1/4
M 2.44 5/8
mm 87 — 101 64 39 106 171 138 to 159 83 114 183 18 187 6
In 4.69 — 5.56 1.65 — 4.91 8.81 6.75 — — — — 9.00 1/4
N 3.44 ②3/4
mm 119 — 141 42 — 125 224 171 — — — — 229 6
In 5.75 — 5.56 1.53 — 4.79 9.81 7.75 — — — — 9.81 1/4
R & RS 4.50 ②3/4
mm 146 — 141 39 — 122 249 197 — — — — 249 6

① Bracket is counter bored to a diameter of 2.687 inches (68 mm), 0.12 inches (3 mm) deep from stuffing box face.
② Studs are used in place of cap screws.
③ For Q, QS size brackets, seal box dimensions differ between O-Pro™ Barrier and traditional seal options. Consult factory for options.

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

UNIVERSAL PRODUCT LINE: Section 1401
CAST IRON — NON-JACKETED PUMPS Page 1401.15
124A Series™, 124AE Series™, 1124A Series™, 1124AE Series™, 4124A Series™, 4124AE Series™,
4124B Series™, 324A Series™, 1324A Series™, 4324A Series™ Issue F

NPSH REQUIRED
Printed performance curves are not available.
Performance curves can be electronically generated with the Viking Pump Curve Generator on vikingpump.com.
NPSHR data is not available on the pump selector.

NPSH (Net Positive Suction Head): The NPSHR (Net Positive Suction Head Required by the pump) is given in the table below
and applies for viscosities through 750 SSU. NPSHA (Net Positive Suction Head – Available in the system) must be greater than
the NPSHR. For a complete explanation of NPSH, see Application Data Sheet AD-19.
FOR VISCOSITIES UP TO 750 SSU – See NPSHR table below.
NPSHR for high viscosities can be estimated using the following method:
1. Calculate line loss for a 1 foot long pipe of a diameter matching the pump inlet port size. Use your flow rate and max viscosity.
2. Convert this value into Feet of Liquid (S.G. 1.0)
3. Add this value to the NPSHR value in the chart below.

PUMP PUMPS SPEED, RPM

SIZE 100 125 155 190 230 280 350 420 520 640 780 950 1150 1450 1750
G — — — — — — — 1.8 2.0 2.2 2.6 3.1 3.9 5.6 7.6
H, HL — — — — 1.7 1.8 1.9 2.1 2.4 2.8 3.4 4.5 6.2 9.5 13.5
AK, AL — — 1.6 1.7 1.8 2.0 2.3 2.7 3.2 3.9 5.5 7.7 11.2 — —
K, KK — 1.7 1.8 1.9 2.1 2.3 2.8 3.3 4.4 6.3 9.1 — — — —
L 1.6 1.8 2.0 2.2 2.5 3.0 3.8 5.0 7.3 10.8 — — — — —
LQ 1.6 1.8 2.0 2.2 2.5 3.0 3.8 5.0 7.3 10.8 — — — — —
LL 1.6 1.8 2.0 2.2 2.5 3.0 3.8 5.0 7.3 — — — — — —
LS 1.6 1.8 2.0 2.2 2.5 3.0 3.8 5.0 7.3 10.8 — — — — —
Q, QS 1.9 2.1 2.3 2.7 3.3 4.2 6.1 8.4 12.7 — — — — — —
M 2.1 2.3 2.8 3.4 4.3 6.0 9.0 12.7 — — — — — — —
N 2.1 2.3 3.5 4.5 6.3 9.5 15.0 — — — — — — — —
R 6.1 7.1 8.3 10.1 12.1 15.2 — — — — — — — — —
RS 7.0 8.5 10.4 13.1 17.2 22.4 — — — — — — — — —

NPSHR – FEET OF LIQUID (Specific Gravity 1.0), Viscosities up to 750 SSU

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020