DCH-5200P

Professional HDTV IRD and Processor

User Manual

http://www.pbi-china.com

-1-
 DCH-5200P

Contents
1. Overview ......................................................................................................................- 5 -
2. Features .......................................................................................................................- 5 -
3. Technical Specifications ............................................................................................- 6 -
4. Front panel and rear panel instructions ................................................................- 11 -
4.1 Front panel .........................................................................................................- 11 -
4.2 Rear panel ..........................................................................................................- 12 -
4.3 RS-232 Serial Port ............................................................................................- 13 -
4.4 Audio DB-9 Port ................................................................................................- 13 -
4.5 Management Ethernet Port .............................................................................- 14 -
4.6 TS over IP Ethernet Port ..................................................................................- 14 -
5. Operation ...................................................................................................................- 14 -
5.1 Local Control ......................................................................................................- 14 -
5.1.1 Getting Started .......................................................................................- 14 -
5.1.2 Main menu ..............................................................................................- 15 -
5.1.3 Configuration Menu ...............................................................................- 16 -
5.1.5 System menu .........................................................................................- 21 -
5.2 Remote Control .................................................................................................- 23 -
5.2.1 Status.......................................................................................................- 23 -
5.2.2 Config--Tuner .........................................................................................- 24 -
5.2.3 Config--Decoder.....................................................................................- 24 -
5.2.4 Config—ASI Output ...............................................................................- 27 -
5.2.5 Config--TS over IP .................................................................................- 28 -
5.2.6 Config--Remux .......................................................................................- 31 -
5.2.7 Config--CI ................................................................................................- 31 -
5.2.8 Config--BISS...........................................................................................- 32 -
5.2.9 Config--Redundancy .............................................................................- 33 -
5.2.10 Config--SDI ...........................................................................................- 33 -
5.2.11 System ..................................................................................................- 34 -
6. Firmware Update ......................................................................................................- 37 -
6.1 Firmware Upgrade from USB Key..................................................................- 37 -
6.2 Firmware Upgrade by FTP ..............................................................................- 38 -
6.3 Firmware Upgrade from WEB .........................................................................- 41 -
7. Installation ..................................................................................................................- 42 -
8. Accessories ...............................................................................................................- 42 -

-2-
 DCH-5200P

Notices
COPYRIGHT (Copyright © 2013 Beijing Jaeger Communication Electronic Technology Co., Ltd.)
Not to be copied, used or translated in part or whole without Beijing Jaeger prior consent in writing
except approval of ownership of copyright and copyright law.
WARRANTY
This warranty does not cover parts which may become defective due to misuse of the information
contained in this manual.
Read this manual carefully and make sure you understand the instructions provided. For your safety,
be aware of the following precautions.
WARNING! IMPORTATNT SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
• To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
• To avoid explosion danger, do not dispose of batteries in an open fire.
CE MARK FOR EUROPEAN HARMONISED STANDARDS
The CE mark which is attached to these products means it conforms to EMC
Directive (89/336/EEC) and Low Voltage Directive (73/23/EEC).

IMPORTANT INFORMATION
Please retain the original packaging, should it be necessary at some stage to return the unit.
Disposal of Old Electrical and Electronic Equipment (Applicable in the European Union and
other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not
be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. The
recycling of materials will help to conserve natural resources. For more detailed
information about recycling of this product, please contact your local Civic Office,
your household waste disposal service, or the shop where you purchased the
product.
COPYRIGHTS
Television programs, movies, video tapes, discs, and other materials may be copyrighted.
Unauthorized recording of copyrighted material may be against the copyright laws in your region.
Also, use of this product with cable television transmissions may require authorization from the cable
television operator or transmitter/owner.
VENTILATION
• Do not expose the product to high temperatures, such as placing it on top of other product that
produce heat or in places exposed to direct sunlight or spot lights.
• The ventilation slots on top of the product must be left uncovered to allow proper airflow into the
unit.
• Do not stand the product on soft furnishings or carpets.
• Do not stack electronic equipment on top of the product.
• Do not place the product in a location subject to extreme changes in temperature. The
temperature gradient should be less than 10 degrees C/hour.
• Place the product in a location with adequate ventilation to prevent the build-up of heat inside the
product. The minimum ventilation space around the unit should be 7 cm. The ventilation should
not be impeded by covering the ventilation openings with items, such as newspapers, table cloth,
curtains, etc.

-3-
 DCH-5200P

POWER SOURCES
• The product is not disconnected from the AC power source (mains) as long as it is connected to
the power outlet or wall socket, even if the product is turned off.
• If the product will not be used for a long period of time, disconnect it from the AC power outlet or
wall socket.

Before Using the Device

Thank you for purchasing the DCH-5200P Professional HDTV IRD and Processor. This User Manual
is written for operators/users of the DCH-5200P to assist in installation and operation. Please read
this user manual carefully before installation and use of the device.
FOR YOUR SAFETY
This equipment is provided with a protective earthing ground incorporated in the power cord. The
main plug shall only be inserted in a socket outlet provided with a protective earth contact. Any
interruption of the protective conductor, inside or outside the device, is likely to make the device
dangerous. Do not remove the covers of this equipment. Hazardous voltages are present within this
equipment and may be exposed if the covers are removed. Only Beijing Jaeger trained and approved
service engineers are permitted to service this equipment.
The supplied AC power cable must be used to power the device. If the power cord becomes
damaged it must be replaced. No operator serviceable parts inside. Refer servicing to Beijing Jaeger
trained and approved service engineers. For the correct and safe use of the device, it is essential
that both operating and servicing personnel follow generally accepted safety procedures in addition
to the safety precautions specified in this manual. Whenever it is likely that safety protection is
impaired, the device must be made in-operative and secured against unintended operation. The
appropriate servicing authority must be informed. For example, safety is likely to be impaired if the
device fails to perform the intended measurements or shows visible damage.
WARNINGS
• The mounting environment should be relatively dust free, free of excessive vibration and the
ambient temperature between 0C° to 40C°. Relative humidity of 20% to 80% (non-condensed) is
recommended.
• Avoid direct contact with water.
• Never place the equipment in direct sunlight.
• The outside of the equipment may be cleaned using a lightly dampened cloth. Do not use any
cleaning liquids containing alcohol, methylated spirit or ammonia etc.
• For continued protection against fire hazard, replace line fused only with same type.
• Air intake for cooling is achieved via holes at the side of the device and the fans inside. The air
flow should not be obstructed. Therefore, the device has to be placed on a flat surface, leaving
some space at the sides of the device.
• When in operation, the internal temperature should not exceed the limit of 70C°.

-4-
 DCH-5200P

Professional HDTV IRD and Processor

1. Overview
The DCH-5200P IRD and Processor provides operators an ideal solution for receiving,
remultiplexing, descrambling and decoding operations. Equipped with a variety of inputs that
ensures compatibility with all transmission media. The DCH-5200P’s remultiplexing capabilities
enable creation of new transport streams that are subsets of the original stream. Customized
services may be output as multiple SPTS or MPTS over IP, as well as over ASI. By the dual
DVB common interfaces, DCH-5200P could decrypt multiple services in one transport stream or
two. DCH-5200P is also a professional IRD that features a broadcast quality decoder for
MPEG-2 and MPEG-4 AVC/H.264 in both Standard Definition and High Definition formats, and
provides a variety of industry standard digital and analog outputs, including CVBS video,
AES/EBU Audio, analog Audio, SD-SDI and HD-SDI. The unit also performs HD
down-conversion and aspect ratio adaptation of HD programs to generate professional quality
baseband analog video and audio outputs for easy integration with e×isting cable network
infrastructure. This all-in-one architecture makes the DCH-5200P an ideal product for
distribution and contribution networks.

2. Features
 Variety of input options DVB-T2/S2/S/C/T/DTMB/ATSC/ISDB-T, DS3/E3, TS/IP, ASI

 Supports DVB-S2 Input Stream Identifier (ISI, optional) and DVB-T SFN MIP pass through

 Redundant backup among Tuner, ASI and TS/IP with configurable priority

 SD/HD MPEG-2 and MPEG-4 AVC/H.264 digital video decoding

 Two Audio PIDs decode or pass through (compressed) in SDI output

 Multiple Analog and Digital Outputs, ASI, CVBS, YPbPr, HDMI, SD/HD-SDI, AES/EBU

Audio, TS/IP

 Built-in TS re-multiple×er receives ASI, Tuner and TS/IP Inputs

 2×DVB-CI Slots, multi-program decryption, BISS-1 and BISS-E decryption

 Dynamic PMT detection and automatic updating

 Supports VBI TELETE×T, EBU/DVB Subtitle, Closed Caption

 UDP/RTP, Unicast/Multicast, and SPTS/MPTS over IP (full duple×, optional)

 Remote Control and Supervision by SNMP, HTTP WEB and Proprietary HDMS software

-5-
 DCH-5200P

 PCM audio embedded in SDI and HDMI outputs

 PCM audio output on two AES/EBU audio output ports

 On Site software update through IP

 RSSI, received Eb/No & BER monitoring

3. Technical Specifications
Tuner Input

DVB-S/S2 Tuner Input (ISI Factory Optional)

1×F type female 75Ω for Input, 1×F type

Connector Type
female 75Ω for loop through output

Input Frequency Range 950 ~ 2150MHz

Input Level -25 ~ -65dBm

Symbol Rate 2 ~ 45MBaud

DVB-S QPSK: 0.35

Roll-off Factor
DVB-S2 8PSK: 0.35, 0.25, 0.2

DVB-S QPSK: 1/2, 2/3, 3/4, 5/6, 7/8

FEC Code Rate DVB-S2 QPSK: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9,9/10

DVB-S2 8PSK: 3/5, 2/3, 3/4, 5/6, 8/9, 9/10

LNB Polarity Selection

0, 13V, 18V selectable
Voltage

LNB Band Selection Tone 0/22KHz selectable

Satellite Selection Command DiSEqC 1.0

ISI ID 1 ~ 255 user configurable

DVB-C Tuner Input

1×F type female 75Ω for Input, 1×F type female 75Ω for loop
Connector Type
through output

Input Frequency Range 51 ~ 862MHz

Input Level 51 ~ 75dBμV

Symbol Rate 1 ~ 7MBaud (ITU J.83 Anne× A)

Constellation 16QAM, 32QAM, 64QAM, 128QAM, 256QAM

Bandwidth 6MHz, 7MHz, 8MHz

Input Return Loss 7dB (typ.)

DVB-T/T2 Tuner Input

1×F type female 75Ω for Input, 1×F type female 75Ω for loop
Connector Type
through output

-6-
 DCH-5200P

Input Frequency 104 ~ 862MHz (VHF/UHF)

Input Level -20 ~ -70dBm

DVB-T: QPSK, 16QAM, 64QAM

Constellation
DVB-T2: QPSK, 16QAM, 64QAM, 256QAM

Bandwidth 6MHz, 7MHz, 8MHz

DVB-T: 2K, 8K
FFT Mode
DVB-T2: 1K, 2K, 4K, 8K, 16K, 32K

DVB-T: 1/4, 1/8, 1/16, 1/32

Guarding Interval
DVB-T2: 1/4, 5/32, 1/8, 5/64, 1/16, 1/32, 1/64, 1/128

DVB-T: 1/2, 2/3, 3/4, 5/6, 7/8

FEC Code Rate
DVB-T2: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6

Input Return Loss 7dB (typ.)

DTMB Tuner Input

1×F type female 75Ω for Input, 1×F type

Connector Type
female 75Ω for loop through output

Input Frequency Range 46.5~866MHz

Input Level -87~-29dBm

Symbol Rate 7.56MBaud

Bandwidth 6MHz/7MHz/8MHz

Constellation 4QAM-NR,4QAM,16QAM,32QAM,64QAM

Guard Interval PN420, PN595, PN945

Roll-off Factor 0.05

Interleaving Depth 240,720

FEC Code Rate 0.4, 0.6, 0.8

ATSC Tuner Input

1×F type female 75Ω for Input, 1×F type

Connector Type
female 75Ω for loop through output

Input Frequency Range 54~864MHz

Input Level -75~-7dBm(ATSC 8VSB)

Symbol Rate 10.762MBaud

Constellation 8VSB

Roll-off Factor 0.115

Bandwidth 6MHZ

ASI Input

Connector Type 1×BNC female, 75Ω

Standard DVB-ASI, EN50083-9

Input Bit Rate ≤ 100Mb/s

-7-
 DCH-5200P

DS3 Input (Option)

Connector Type 2×BNC female, 75Ω, including loop through

Standard Compliant with ITU-T G.703

Frame Structure Compliant with ITU-T G.752 and ITU-T G.804

Bit Rate 44.736Mb/s

TS over IP

Connector Type 1×RJ-45, 10/100 Base-T or 100/1000 Base-T for TS/IP

Effective Bit Rate 70Mb/s for 10/100/1000 Base-T

Protocol UDP / RTP, Multicast / Unicast, IGMPv3, ARP

TS Processing

Demu× and Remu× among Tuner / DS3(optional) / E3 (optional),

TS Input Management
ASI and TS/IP Inputs

TS Output Management Demu× and Remu× for 2 independent ASI outputs

Service and PID Management Remu×, filtering and remapping

PSI/SI table regeneration, NIT and SDT edition, LCN Edition and
PSI/SI
Re-generation

Descrambler DVB Common Scrambling Algorithm (CSA)

BISS Mode BISS-1, BISS-E

Double PCMCIA slots, compatible with major CA CAMs in the

Common Interface
market

ASI Output

Connector Type 2 pairs of BNC female, 75Ω

Standard DVB-ASI, EN50083-9

Output Bit Rate ≤ 99Mb/s

2 Independent TS Re-multiple×ed from tuner, TS/IP and 2 ASI

TS Processing
inputs

HDMI Output

Standard 1×HDMI 1.3 interface (up to 1080i)

Video Resolution and Frame 1080i×30, 1080i×29.97, 1080×25,720p×60,720p×59.94,

Rate 720p×50, 480p×60, 576p×50, 576i×25, 480i×29.97

Audio Embedded 1×stereo

Digital Video Processing

Video Standard MPEG-2(MP@ ML for SD, MP@HL for HD)

MPEG 4/H.264 AVC Part 10 (MP@L3 for SD, [email protected] for HD)

SDI Video Resolution 1080i×30, 1080i×29.97, 1080i×25, 720p×60, 720p×59.94,

720p×50, 576i×25, 480i×29.97

Video PID Bit Rate < 80Mb/s

-8-
 DCH-5200P

HD/SD-SDI Output

Connector Type 1 pair of BNCs (mirrored) , female, 75Ω

SD Standard SMPTE 259M, 270 Mb/s (10bit)

HD Standard SMPTE 292M, 1.485 Gbit/s (10bit)

Level 800mV p-p

Digital Audio Processing

Connector Type 2×D-sub 9 male with ×LR adaptor cables

Number of Output 2×audios are decoded or passed through

Audio Sampling Rate 32, 44.1 and 48 KHz

Audio Bit Rate 32, 64, 96, 128, 160, 192, 224, 256, 288, 320, 352, 384, 416

and 448 Kb/s for MPEG-1 Layer I, 32, 48, 56, 64, 80, 96, 112,

128, 160, 192, 224,256, 320 and 384 Kb/s for MPEG-1 Layer II

Nominal Output Level 1V p-p (with standard test stream)

Output Format AES/EBU

Load Impedance 110Ω (with ×LR adaptor cables)

Analog Video Output

CVBS Connector 2×BNC female 75Ω

CVBS Standard NTSC, PAL, and SECAM

CVBS Resolution 576i×25, 480i×29.97

Norminal Output Level 1.0 Vp-p±5% (with standard test stream)

Frequency Response <±1 dB, at 5.5 MHz for PAL/SECAM, 4.2MHz for NTSC

Chroma-Luma Delay <±30 ns

Field Time Distortion <2%

Line Time Distortion <1%

Short Time Distortion <2%

Differential Gain <3%

Differential Phase <2°

Signal to Noise Ratio >55dB (luminance weighted)

Analog Audio Output

Connector Type 2×D-sub 9 male, with ×LR adaptor cable

Output Impedance 600Ω (balanced)

Output Mode Left, Right, Dual Mono, Stereo

Number of Output 2 pairs of stereo audio outputs (2 Audio PIDs or 4 channels are

decoded).

Cross Talk Among Channels >70dB

THD <0.3% @ 400Hz, 1KHz test tone

Frequency Response ±0.5dB over 20Hz ~ 18KHz

-9-
 DCH-5200P

Output Level 0dBm in 600Ω (0dBu), adjustable range ±I0dB

Ancillary Data Processing

Subtitle DVB, EBU

VBI Telete×t, WSS

Closed Caption EIA 608, EIA 708, EIA 608-to-708

Redundancy

Redundancy Port among Tuner, ASI input and TS/IP input

Switching Condition TS Sync Loss

Switching Mode Main, Spare

Control & Monitoring

Connector Type 1×RJ-45, 10/100 Base-T, for equipment IP Control

Remote Control SNMP, HTTP (Web Interface), Proprietary HDMS (Headend Device

Management System)

Local Control LCD display and 6-key keypad

Serial Port 1×RS-232 D-sub female, for debug use only

Equipment Upgrade Embedded FTP loader and Telnet

Physical

Dimension 44mm×483mm×255mm

Weight 3.4Kg Net, 5.4Kg Gross

Power Supply AC 90V ~ 250V, 50/60Hz

Power Consumption 24W (e×clusive of LNB power)

Operating temperature 0 ~ 45℃

Storage temperature -10 ~ 60℃

Operating Humidity 10 ~ 90%, non-condensed

Certification

EMC: EN 55024:1998+A1:2001+A2:2003, EN 55022:2006+A1:2007, EN 61000-3-2:2006, EN

61000-3-3:2008

FCC: Part 15 Class B

LVD: EN 60950-1:2006 + A11:2009

* For more information about digital audio pass through, please contact our sales
representative.

- 10 -
 DCH-5200P

Order information

DCH-5200P

Model -10X -20X -30X

Function -20X -22X -24X -26X -30X -32X -34X -36X
2*BNC(one
CVBS ● ● ● ● ● ● ● ● ●
for mirror)
Standard
Video/Audio AUDIO 2*R/L ● ● ● ● ● ● ● ● ●
HD-VIDEO 1*HDMI ● ● ● ● ● ● ● ● ●
HD-SDI 2*BNC ● ● ● ●
Digital 2*D9(with
Video/Audio extended
AES/XRL ● ● ● ●
cable
adaptor)
TS Input ASI IN 1*BNC ● ● ● ●
4*BNC(2 for
TS Output ASI OUT ● ● ● ● ● ● ● ●
mirror)

100M/6 channel 2*RJ45(one

● ●
multicast for mirror)

TS/IP 100M/32
channel 1*RJ45 ● ●
multicast
GbE 1*RJ45 ● ●
Mangement 1*RJ45 ● ● ● ● ● ● ● ● ●
Upgrade 2*USB ● ● ● ● ● ● ● ● ●
Control/Upgrade
RS-232 1*D9 ● ● ● ● ● ● ● ● ●

ALARM/RELAY 1*D9 ● ● ● ● ● ● ● ● ●

-C DVB-C
-T DVB-T
-S2 DVB-S2
-T2 DVB-T2
TUNER Factory default option: X=S2
-D DS3
-M STM-1
-A ASI
-N no TUNER

4. Front panel and rear panel instructions

4.1 Front panel

- 11 -
 DCH-5200P

Name Function

When turned on, the Green LED indicates that power is available. When
LED Power
turned off, the power is not available or failed

LED ON: Tuner input is locked,

LED Tuner Lock
LED OFF: Tuner is un- locked.
LED ON: Alarm or alarms happen to the equipment, For alarm description,
LED Alarm please refer to details in the table 10.
LED OFF: The equipment works properly
LCD Display Display menus, submenus and its parameters
Cursor Keys UP, DOWN, LEFT, RIGHT. Used to navigate through the menu system
ENTER key Confirm a selection then return to previous menu
EXIT Key Exit and return to previous menu
Common Interface To insert CI CAM modules, maximum two CI modules

4.2 Rear panel

Name Description
TS/IP(option) TS over IP input or output
RS-232 Serial port for equipment debug use
ASI OUT2 Group 2 of 2 ASI output ports in mirror
ASI OUT1 Group 1 of 2 ASI output ports in mirror
ASI IN ASI input port
Alarm
L-Audio-R1 Group 1 of RCA audio left and right outputs port
L-Audio-R2 Group 2 of RCA audio left and right outputs port
AES/EBU and Balance Audio output port 1 (A special DB-9 conversion
Audio 1
cable is offered as accessory)
AES/EBU and Balance Audio output port 2 (A special DB-9 conversion
Audio 2
cable is offered as accessory)
TUNER OUT Tuner signal loop through output port
TUNER IN Tuner signal input
SWITCH AC Power supply switch
Control RJ-45 Ethernet port for equipment control and supervision
Control USB port for firmware upgrade

- 12 -
 DCH-5200P

SDI 2 SD or HD Serial Digital Video output port 2

SDI 1 SD or HD Serial Digital Video output port 1
HDMI High Definition Multimedia Interface output port
CVBS CVBS RCA video output port

Grounding terminal

POWER SOCKET AC 90~250V 50-60Hz input

4.3 RS-232 Serial Port

The RS-232 port is used for equipment software debug use, its pin definition is shown in the table.
The parameter settings are:
● No Parity bit
● 38400 Bauds
● 8 data bits
● 1 Stop bit

Pin Pin Function

1 N.C.
2 TXD
3 RXD
4 N.C.
5 GND
6 N.C.
7 N.C.
8 N.C.
9 N.C.

4.4 Audio DB-9 Port

DCH-5200P uses a special DB-9 port for AES/EBU and balanced Audios. Pins are defined in below
Table.

Pin Pin Function

1 AES Audio (+)
2 AES Audio Ground
3 Left Channel (-)
4 Right Channel (-)
5 Right Channel Ground
6 AES Audio (-)

- 13 -
 DCH-5200P

7 Left Channel Ground

8 Left Channel (+)
9 Right Channel (+)

4.5 Management Ethernet Port

The Management port is used to remote control and supervise the equipment through IP, it’s also for
the software update. Its factory setting is as following:

 IP address:10.10.70.48
 Sub Mask:255.255.255.0
 Gateway:10.10.70.1

Both web based control software and proprietary HDMS software are using this port.

Notice: When apply default setting to DCH-5200P, the above settings for IP will not be affected, this
is for maintaining the connectivity of the unit to the IP Network.

4.6 TS over IP Ethernet Port

The TS over IP port is an option by adding the daughter board inside the rack. The default setting is
as following:

 IP address:10.10.10.10
nd
 2 IP address: 10.10.10.20 (for option DCH-5100P-32x, if equipped)
 Sub Mask:255.255.255.0
 Gateway:10.10.10.1

Depending on the option selected by the customer, this TS over IP port is either 10/100 Base-T or
100/1000 Base-T compliant to the IEEE 802.3 specifications.

5. Operation
5.1 Local Control
5.1.1 Getting Started
After successful installation and connection of the Professional IRD Processor DCH-5200P, switch
on the power supply. The equipment will check the hardware and software versions, then the product

- 14 -
 DCH-5200P

name and its IP address will be shown in the LCD screen.

Professional IRD
IP: 10.10.70.48

The IP address of the equipment can be changed in the System menu. Go into the Local Setup
submenu, user can set IP address, network mask and IP gateway, press ENTER to select the option,
and use LEFT or RIGHT to move the cursor between digits and use UP or DOWN to change the
value until the right value, then press ENTER to make the selection.

IP Address
10.10.70.48

Network Mask
255.255.255.0

Gateway
10.10.70.1

Customers can use UP, DOWN, LEFT,RIGHT, ENTER, EXIT keys from front panel to navigate in the
menus, select and confirm the parameters in LCD screen.

5.1.2 Main menu

User can press ENTER into the main menu. In the main menu, there are 3 sub-menu, Press
UP/DOWN to switch between the sub-menus.

● Status
● Config
● System
After go into every sub-menu, you can press LEFT or RIGHT to move the cursor, then use UP or
DOWN to change the value, and then you can press ENTER to make the selection.

- 15 -
 DCH-5200P

Submenu Name Description

Monitor the parameters of Tuner, TS over IP input (only when the TS/IP
Status
streaming board is installed) and decoding info.
Configure the parameters of Input and output, including CI settings, AV
Config
decoder, ASI output and so on.
Check and set system settings and read the equipment information, and
System
make the default factory setting and so on.

5.1.3 Configuration Menu

In the Configuration menu, user can configure and monitor the parameters of input and output,
including Tuner, CI settings, AV decoder, ASI output, BISS, SDI, TS over IP input (only when the
TS/IP streaming board is installed) and so on. Choose Configuration and press UP or DOWN to
scroll the sub-menus, press ENTER to go into the sub-menus. There are ten sub-menus to configure:

● Tuner
● Decoder
● ASI-1 Output
● ASI-2 Output
● TS over IP
● Remux
● CI
● BISS
● Redundancy
● SDI

- 16 -
 DCH-5200P

- 17 -
 DCH-5200P

Submenu Name Description

LNB LO Frequency To configure the local oscillator frequency

according to the right satellite, its range is from
1000 to 26,500MHz.
Satellite Frequency To configure the satellite down link frequency
according to the right satellite, its range is from
1000 to 26,500MHz.
Symbol Rate To configure the symbol rate of QPSK signal, its
range is from 1000 to 45,000KBaud.
LNB Voltage To select the correct LNB voltage output from the
F-connector, user can choose between Off, 13V
and 18V.
Tuner LNB 22KHz To activate the LNB 22KHz control signal to the
LNB, user can select between On and Off.
DiSEqC To configure the DiSEqC control, user can select
Port A, Port B, Port C, Port D or DiSEqC OFF.
PLS Gold Code To configure the PLS gold code, its range is from 0
to 262,141.
Freq Offset High To ensure the tuner locks the specific signal, its
range is from 1000K to 5,000KHz.
Freq Offset Low To ensure the tuner locks the specific signal, its
range is from -5,000K to -1,000KHz. The condition
is “Freq Offset Low < Real IF - Setting IF < Freq
Offset High”.
Source To configure the decoder source, user can select
Tuner Input, ASI-1 Input, ASI-2 Input, IP Input or
Remux Input.
Program To configure which program should be decoded.
Video Output To configure the video properties, such as the
screen ratio, resolution, VBI issues and so on.
Audio Output To configure the audio properties, such as the
Decoder
audio PID, output level and so on.
Mode To configure which program should be decoded
when the decoder source is changed, user can
select between First Service and Program Manual
Selection.
A/V Alarm Switch To enable or disable the A/V alarm, user can
choose between On and Off.

- 18 -
 DCH-5200P

ASI-1 ASI-1 Source To select the ASI-1 output source.

ASI-2 ASI-2 Source To select the ASI-1 output source.
When set IP Board Type as Single IP input
Stream IP Address To configure the IP address of the TS over IP port.
Stream Netmask To configure the Netmask of the TS over IP port.
Stream Gateway To configure the Gateway of the TS over IP port.
Stream Mac Address To display the Mac address of the TS over IP port.
Uni/Multicast IP To configure the unicast or multicast address of TS
over IP input.
Uni/Multicast Port To configure the unicast or multicast port of TS
over IP input.
Protocol To select the correct protocol to receive the IP input
stream, user can select UDP or RTP.
Output Smoothing To adjust the clock of the IP stream, user can
select Auto, Fixed Rate and Disable.
IGMP Version To select the correct IGMP version according to the
IP out device, user can select IGMP v2 or IGMP v3.
TS Buffer Size To select the TS over IP buffer size.
When set IP Board Type as 6-CH Dual IP output or 32-CH Single IP output
Stream IP Address To configure the IP address of the TS over IP port.
TS over IP
Stream Netmask To configure the Netmask of the TS over IP port.
Stream Gateway To configure the Gateway of the TS over IP port.
Stream Mac Address To display the Mac address of the TS over IP port.
Gateway Mac Address To configure the Mac address of the TS over IP
gateway.
Protocol To select the correct protocol to receive the IP input
stream, user can select UDP or RTP.
TS Pkts per UDP To configure the IP packet include how much DVB
PES packets.
Time to Live To define the maximum of multi switch the IP
stream can be passed, user can set the value from
1 to 255.
Type of Service To match the multi switch settings, user can select
Normal, Min Delay, Max Throughput, Max
Reliability or Min Monetary Cost
Source To configure the TS/IP source.
Mode To configure the TS/IP output mode, user can
choose between DVB and IPTV.

- 19 -
 DCH-5200P

Uni/Multicast Setup To configure the TS/IP output parameters, such as

unicast or multicast address, port and so on.
Remux Switch To enable or disable the Remux function.
Max Bit Rate To set the Max bit rate of the Remux output.
Remux
TS ID To set the TS ID.
Program List To select which services will be output by Remux.
CI Source To configure the CI descramble source, user can
select Tuner Input, ASI-1 Input, ASI-2 Input, IP
Input or Remux Input.
CI
CI Setup To set which programs should be descrambled by
CI slot1 or CI slot2.
CI CAM Name To check what kind of CAMs have been inserted.
BISS Mode To select the BISS mode, user can choose
between Off, BISS-1 and BISS-E.
BISS BISS Source To select the BISS source, user can select Tuner
Input, ASI-1 Input, ASI-2 Input or IP Input.
Program To select which services will be decrypted by BISS.
Emb Aud Switch To enable or disable the embedded audio
Emb Aud Mapping To select which audio to be embedded in which
group
SDI
Closed Caption Mode To configure the Closed Caption mode over SDI,
user can select between Auto, Line21, SMPTE
334-608 and SMPTE 334M-708.
Switch To enable or disable the Redundancy function
Main Port To configure the main output source, user can
select Tuner Input, ASI-1 Input, ASI-2 Input or IP
Input.
Backup Port To configure the backup output source, user can
select Tuner Input, ASI-1 Input, ASI-2 Input or IP
Redundancy
Input. The backup port can not select the same
source as main port.
Main CH Unlock Time To define the condition of the backup port.
Main CH Recover Time To define the condition when the main port recover.
Backup Mode To configure the decoder output mode, user can
select between Auto and User Define Program.

- 20 -
 DCH-5200P

5.1.5 System menu

In this menu, you can check and set system settings and read the equipment information, and make
the default factory setting and so on. There are nine submenus, including Version Info, IP Control,
Product Name, Model, Factory Settings, Machine Type, LCD Language, Safety Level, and Upgrade.
Use UP or DOWN key to scroll the submenu, and press ENTER to go into each submenu.

● Version Info
● IP Control
● Product Name
● Model
● Factory Settings
● Machine Type
● LCD Language
● Safety Level
● Upgrade

Submenu Name Description

Version Info To display some properties of the device, such as software version.
IP Address To configure the IP Address of the device.
IP Control
Network Mask To configure the IP Net Mask of the device.

- 21 -
 DCH-5200P

Gateway To configure the IP Gateway of the device.

HTTP Login To configure the user name and password of
web access.
NTP To configure NTP parameters.
MAC Address To display the MAC address of the device
Product Name To configure the product name of the device.
Model To configure the model number of the device
Factory Settings The switch to make factory default setting.
MAC Address To configure the MAC address of the device.
Machine Type S/N To configure the serial number of the device.
Dynamic PMT Switch To enable or disable the dynamic PMT function.
LCD Language To switch LCD display language between English and Chinese
Safety Level To configure a special safety mode in China market.
To start to upgrade firmware after inserting a USB storage which contain new
Upgrade
firmware file into the USB port of the device.

- 22 -
 DCH-5200P

5.2 Remote Control

DCH-5200P can be controlled by WEB. User can type IP address of DCH-5200P in
browser. It will show login pop-up. The default user name is root and password is
12345. If you forget this username and password, you can use front panel button to
change it. You can set it in SystemHTTP login menu. The parameters are the
same as Chapter 3.3.

5.2.1 Status
User can monitor the status of inputs and output. All information of every input
source can be shown in this page. The output status and information can also be
checked.
Input TS—User can monitor TS status of Tuner, ASI, CI and IP here.

Decoder—User can monitor video and audio decoding status here.

- 23 -
 DCH-5200P

5.2.2 Config--Tuner
Set parameters of tuner input, it is used to lock the right satellite. The description of
parameters is shown in below. Click “Apply” button to submit, or click “Cancel”
button to cancel.

Menu Name Description

To configure the local oscillator frequency according to the right satellite,

LNB LO Frequency
its range is from 1000 to 26,500MHz.
To configure the satellite down link frequency according to the right
Satellite Frequency
satellite, its range is from 1000 to 26,500MHz.
To configure the symbol rate of QPSK signal, its range is from 1000 to
Symbol Rate
45,000KBaud.
To select the correct LNB voltage output from the F-connector, user can
LNB Voltage
choose between Off, 13V and 18V.
To activate the LNB 22KHz control signal to the LNB, user can select
LNB 22KHz
between On and Off.
To configure the DiSEqC control, user can select Port A, Port B, Port C,
DiSEqC
Port D or DiSEqC OFF.
PLS Gold Code To configure the PLS gold code, its range is from 0 to 262,141.
To ensure the tuner locks the specific signal, its range is from 1000K to
Frequency Offset High
5,000KHz.
To ensure the tuner locks the specific signal, its range is from -5,000K to
Frequency Offset Low -1,000KHz. The condition is “Freq Offset Low < Real IF - Setting IF <
Freq Offset High”.

5.2.3 Config--Decoder

- 24 -
 DCH-5200P

Set parameters of decoder. There are three subpages, Program page, Video Output
page and Audio Output page. In the Program subpage, user can set the parameters
of output program. Click “Apply” button to submit, or click “Cancel” button to cancel.

Menu Name Description

To configure the decoder source, user can select Tuner Input, ASI-1
Source
Input, ASI-2 Input, IP Input or Remux Input.
Current Program To show which program should be decoded.
Program List Programs which can be selected.
To configure which program should be decoded when the decoder
Decoder Mode source is changed, user can select between First Service and Program
Manual Selection.
To enable or disable the A/V alarm, user can choose between On and
A/V Alarm Switch
Off.

In the Video Output subpage, user can set the video parameters of output program.
Click “Apply” button to submit, or click “Cancel” button to cancel.

- 25 -
 DCH-5200P

Menu Name Description

Video Standard To configure the video output resolution.
Aspect Ratio To configure the video output screen ratio.
DVB Subtitle Language To select the DVB subtitle language.
EBU Subtitle Language To select the EBU subtitle language.
Subtitle Priority To configure the display priority of the subtitle.
Fail Mode To configure the video output mode when change program.
Closed Caption The switch to enable or disable the closed caption.
VBI Mode(TTX/CC/WSS) The switch to enable or disable the VBI output.
To select the CVBS PAL mode when the video resolution is set as
CVBS SUB PAL
1080ix25, 720px50,576px50 or 576ix25.
To select the CVBS NTSC mode when the video resolution is set as
CVBS SUB NTSC 1080ix30,1080ix29.97,720px60,720px59.94,480px60, 480px59.94 or
480ix29.97.

In the Audio Output subpage, user can set the audio parameters of output program.
Click “Apply” button to submit, or click “Cancel” button to cancel.

- 26 -
 DCH-5200P

Menu Name Description

Audio-x Level To configure the analog audio output level.
To set output audio mode among “Auto”, “Stereo”, “Left”, “Right” and
Audio-x Mode
“Mono”
Audio-x Priority To configure output audio priority.

5.2.4 Config—ASI Output

Set parameters of ASI output. There are two ASI output ports, you can select the
input source in this page. Click “Apply” button to submit, “Refresh” button to refresh
latest status of settings, or click “Cancel” button to cancel.

- 27 -
 DCH-5200P

Menu Name Description

ASI-1 Output Source To configure which TS should be output by ASI-1 Output.
ASI-2 Output Source To configure which TS should be output by ASI-2 Output.

5.2.5 Config--TS over IP

TS over IP function is also an optional function, you can select the IP board type in
this page. For the different IP board type, TS over IP page will show the different
parameters.
When Single IP Input option is selected, the following page will be shown. Click
“Apply” button to submit, or click “Cancel” button to cancel (DCH-5200P-34xx model
only).

When 32CH Single Output option is selected, the following page will be shown.
Click “Apply” button to submit, or click “Cancel” button to cancel (DCH-5200P-34xx
model only).

- 28 -
 DCH-5200P

When 6CH Dual Output option is selected, the following page will be shown. Click
“Apply” button to submit, or click “Cancel” button to cancel (DCH-5200P-32xx model
only)

- 29 -
 DCH-5200P

When 32CH Single Output option is selected, there are two modes that
Uni/Multicast parameters can be configured. If select DVB mode and click
Uni/Multicast Setup button, it will show following page:

If select IPTV mode and click Uni/Multicast Setup button, it will show like this:

Note: It is slightly different in TS over IP page according to the different hardware

configuration of DCH-5200P.

- 30 -
 DCH-5200P

5.2.6 Config--Remux
Set parameters of programs remuxing. The Remux function is a optional function,
you can active or close this option in the System page. In this page, all programs
can be shown in the Input TS window, you can select the programs that need to be
remuxed, and then type button to add the programs into the Output TS window.
If you want to delete the programs from remixed TS, you can type button to
delete the selected programs. Please don’t forget click “Apply” button to save the
setting, or click “Cancel” button to cancel.

Menu Name Description

Remux Switch The switch to enable or disable the Remux function.
Max Bit Rate(kbps) To configure the output total bit rate.
TS ID To configure the TS ID.
Valid Bit Rate(kbps) To display the valid bit rate of the TS output.
Input TS The interface to select the input TS.
Output TS To display the output TS of the Remux.

5.2.7 Config--CI
Set parameters for CI descrambling. Before you want to active this function, you

- 31 -
 DCH-5200P

have to insert the right CI cards into the CI slots. When select the right Input Source,
the programs will be listed in the table, you can descramble the right programs.
Click “Apply” button to submit, or click “Cancel” button to cancel.

5.2.8 Config--BISS
Set parameters of BISS Descryption. DCH-5200P supports BISS-1 and BISS-E
mode. Click “Apply” button to submit, or click “Cancel” button to cancel

Menu Name Description

Source To select the TS stream which you want to do BISS decryption
To select the correct BISS mode, user can choose between BISS-0,
BISS Mode
BISS-1 and BISS-E.

- 32 -
 DCH-5200P

Input Key value in BISS-1 mode and input ID and Key in BISS-E
ID and Key
mode.
BISS Program To configure the programs should be decrypted.

5.2.9 Config--Redundancy
Set parameters of Redundancy. Redundancy function can help to improve the
system’s security, backup parameters can be set in this page. User can active or
close this function in System page. Click “Apply” button to submit, or click “Cancel”
button to cancel.

5.2.10 Config--SDI
Set parameters of SDI output, such as Embedded audio and Close caption. Click
“Apply” button to submit, or click “Cancel” button to cancel.

- 33 -
 DCH-5200P

Menu Name Description

Emb Aud Switch To enable or disable embedded audio function.
To Select the mode of closed caption among “Auto”, “Line21” and
Closed Caption Mode “SMPTE 334M-608” and “SMPTE 334M-708”. (Note: must enable
closed caption function in Decoder menu first.)
SDI Channel x-x To set audio embedded channel.
SDI Channel x-x Audio level To adjust audio level on that channel.

5.2.11 System
Set parameters of system. There are three subpages, Device page, IP Control Page,
Version page, Login Page, Factory Default page, System Reboot and Upgrade page.
In Device subpage, user can set the Product name, Model number, Brightness of
LCD on front panel and Web auto refresh Time. Click “Apply” button to submit, or
click “Cancel” button to cancel.

- 34 -
 DCH-5200P

In IP Control page, user can set the network management parameters and active
NTP function. Click “Apply” button to submit, or click “Cancel” button to cancel.

In Version subpage, user can read the software version.

- 35 -
 DCH-5200P

In Login page, user can set your own username and password to access webGUI of
DCH-5200P.

In Factory Default page, user can restore factory default configuration of

DCH-5200P.

In System Reboot page, user can reboot DCH-5200P.

- 36 -
 DCH-5200P

In Upgrade page, user can upgrade the latest firmware of DCH-5200P. Click
“Choose File” button to select a firmware upgrade package from your PC. Then
click “Upload File” to start upgrading.

6. Firmware Update
Before upgrading the digital TV head-end equipment, please check whether the
Hardware and Software are compliant with the version in the release note.

6.1 Firmware Upgrade from USB Key

The firmware is contained in a file named “target.tgz”. Copy this file in a USB key,
connect the key to the USB port of the equipment to be updated. If the equipment
can detect the file “target.tgz” in the USB key, user can see the message “USB
Found“ in the System->USB Status menu of LCD screen.

The firmware upgrade will start automatically if the firmware version in the USB key

- 37 -
 DCH-5200P

is higher than the version in the equipment. It is impossible to make firmware

downgrade in automatic mode.

If the firmware version in the USB key is equal or lower than the version in the
equipment, user can use the “Force Mode” in the System menu: System -> USB ->
Force Upgrade”.

The equipment will reboot automatically when the software upgrade is finished.

After the firmware upgrade, please check the new version from the menu of front
panel LCD: System->Properties”, or from the web control software.

6.2 Firmware Upgrade by FTP

Connect the equipment to a PC via a cross over CAT-5 (RJ45) LAN cable or a
normal cable using IP switch/hub. Please ensure that the equipment and the PC are
in the same local area network before upgrade.

Figure 1: IP Connection Diagram

Turn on the equipment until the booting is completed. Check the IP address from
the LCD screen on front panel, the default IP address is 10.10.70.48. Please make
sure that the equipment and your PC are in the same IP network, refer to Figure 1.
Important: DON’T switch off the equipment and your PC during the software
upgrade.

Open the IE browser and type ftp://10.10.70.48 in the address bar and press Enter.
If the network configuration is correct, you can open the FTP folder without any error,
as shown below.

- 38 -
 DCH-5200P

Figure 2: Open the FTP folder

Enter the “ftp://10.10.70.48/pub” folder, then copy the “target.tgz” file in this folder,
as shown below.

Figure 3: Copy “target.tgz” File

Open MS-DOS window by typing Start on the lower left quarter of Windows OS.
Select Run and key in “cmd” in dialog and press Enter. Type the command “telnet
10.10.70.48”; the current IP address of the equipment under software upgrade as
below.

- 39 -
 DCH-5200P

Figure 4: Open MS-DOS Window

Type Enter to go into the login window. Use “root” as login name and “12345” as
password.

Figure 5: Login Menu

Key in the command “upgrade” and press Enter. The upgrade process will be
launched.

- 40 -
 DCH-5200P

Figure 6: Upgrading

When the upgrade is finished, the equipment will reboot automatically.

Check the new version through “LCD: System->Properties”, or from web control
page.

6.3 Firmware Upgrade from WEB

Open the Web control page of the equipment. Go to the “upgrade” function in the
SYSTEM menu. Browse the file named “Target.tgz”, click Upload file button, then
the firmware is automatically uploaded in the memory of the equipment. After the
upgrade, check the version number in the SYSTEM menu.

- 41 -
 DCH-5200P

7. Installation
 Fix the device in the standard 19” rack.
 Connect the power cable. Turn on the device and wait for 8 to 10 seconds, while the
device will complete self inspection and configuration. The POWER Indicator LED will
always light on during working. If not use the device, please pull out the AC plug. If
user wants to reboot device, please leave it for at least 5 seconds after shutting it
down.

8. Accessories
CD-ROM 1PC
Power cable 1PC
ASI cable 1PC
Balance audio to RCA cable 2PC
BNC to RCA Adapter 4PC
Certificate of quality /Guarantee card 1PC

- 42 -