Scribd Logo
Upload

Welcome to Scribd!

  • 22 views

    EE387-V2 - Experiment No.9

    Uploaded by

    Hazel Balasbas
    This document describes an experiment on R-C series and parallel circuits performed by students. The objectives were to measure the phase angle between voltage and current, and calculate impedance. Components included resistors, capacitors, an oscilloscope and signal generator. Procedures involved connecting circuits and measuring voltages and currents. Tabulated data included phase angles, impedances, and calculations. Graphs showed voltage and current signals. The conclusion and student contributions were not included.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    EE387-V2 - Experiment No.9

    Uploaded by

    Hazel Balasbas
    22 views6 pages
    This document describes an experiment on R-C series and parallel circuits performed by students. The objectives were to measure the phase angle between voltage and current, and calculate impedance. Components included resistors, capacitors, an oscilloscope and signal generator. Procedures involved connecting circuits and measuring voltages and currents. Tabulated data included phase angles, impedances, and calculations. Graphs showed voltage and current signals. The conclusion and student contributions were not included.

    Original Title

    EE387-V2_Experiment No.9

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document describes an experiment on R-C series and parallel circuits performed by students. The objectives were to measure the phase angle between voltage and current, and calculate impedance. Components included resistors, capacitors, an oscilloscope and signal generator. Procedures involved connecting circuits and measuring voltages and currents. Tabulated data included phase angles, impedances, and calculations. Graphs showed voltage and current signals. The conclusion and student contributions were not included.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    22 views6 pages

    EE387-V2 - Experiment No.9

    Uploaded by

    Hazel Balasbas
    This document describes an experiment on R-C series and parallel circuits performed by students. The objectives were to measure the phase angle between voltage and current, and calculate impedance. Components included resistors, capacitors, an oscilloscope and signal generator. Procedures involved connecting circuits and measuring voltages and currents. Tabulated data included phase angles, impedances, and calculations. Graphs showed voltage and current signals. The conclusion and student contributions were not included.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

    CEBU CITY

    EE387 - V2 - C2
    BASIC ELECTRICAL AND ELECTRONICS ENGINEERING LAB

    EXPERIMENT NO. 9
    R-C CIRCUIT (SERIES AND PARALLEL)

    GROUP NO. 1
    DATE PERFORMED: 12/13/2022
    DATE DUE: 12/23/2022

    SUBMITTED BY:

    ALARBA, PEDROCHE N.
    BALASBAS, HANNAHZEL G.
    CABESAS, MARK ANTHONY E.
    CAM, LEX MARION D.
    CATINGUB, KANDACE THEA C.
    BSCHE – 2,3,4

    SUBMITTED TO:

    ENGR. JUDE DAVID T. BADAL


    INSTRUCTOR
    I. OBJECTIVES

    1. To measure the phase angle between voltage and current in series and parallel
    R-C circuit.
    2. To calculate the impedance of series and parallel R-C circuits.

    II. INSTRUMENTS AND COMPONENTS

     Module DL 3155M07
     Oscilloscope
     Signal Generator
     Cable Set
     R1 = 1 kΩ - 1/4W – 5%
     R2 = 1 kΩ - 1/4W – 5%
     R3 = 10 Ω - 1/4W – 5%
     C1 = 1 µF – Metallized film
     C2 = 1 µF – Metallized film

    III. PROCEDURE

    Series R – C Circuit

    1. The Module DL 3155MO7 was inserted on the console and the main switch was
    set on.
    2. The circuit was connected as shown in Figure 4.1.
    3. The oscilloscope was adjusted with the following settings:
    CH1 = 1V/DIV
    CH2 = 20mV/DIV
    TIME/DIV = 0.2mS
    Coupling = AC
    4. The generator was supplied and the output was adjusted to 6V peak to peak at
    500Hz.
    5. The signal displayed in the oscilloscope was drawn in graph 4.1 and the input
    signal was represented in continuous line and signal across R3 was dotted in
    line.
    6. The values of the peak input voltage were measured and write in table 4.1
    7. The values of the peak input voltage across R3 were measured and write in table
    4.1.
    8. The values of peak current were calculated and write in table 4.1.
    9. The values of the period of alternating voltage were measured and write in table
    4.1.
    10. The number of degrees per division was calculated and written in the table 4.1.
    11. The wave across R3 was set to the center of screen.
    12. The number of the horizontal division from the center of the screen was read and
    the voltage and current were written on table 4.1.
    13. The phase angle was determined when the product of the result in procedure
    number 10 and 12 and were written on table 4.1.
    14. The channel to probe was move from jack 4 to jack 3.
    15. The channel 2 probe was adjusted to 0.5V/DIV.
    16. The signal across C1 displayed in oscilloscope was drawn in graph 4.1 and the
    curve was represented in a continuous line.
    17. The peak voltage across C1 was measured and written on table 4.1.
    18. The voltage across R1 was calculated and written on table 4.1.
    19. The phase angle was calculated and written on table 4.1.
    20. The impedance was calculated and written on table 4.1.

    Parallel R – C Circuit

    1. The circuit was connected as shown in Figure 4.1


    2. Switch S1 was set to On.
    3. Oscilloscope was adjusted with the following settings:
    CH1 = 1V/DIV
    CH2 = 50mV/DIV
    TIME/DIV = 0.2 mS
    Coupling = AC
    4. The generator was supplied and the output was adjusted to 6V peak to peak at
    500Hz.
    5. The signal displayed in the oscilloscope was drawn in graph 4.2 and the input
    signal was represented in continuous line and signal across R3 was dotted in
    line.
    6. The peak input voltage was measured and were written in table 4.1.
    7. The peak voltage across R3 was measure and written on table 4.1.
    8. The peak current was calculated and written on table 4.1.
    9. The period of alternating voltage in division was measured and written on table
    4.1.
    10. The number of degrees per division was calculated and written on table 4.1.
    11. The wave representing the current was set to the center of the screen.
    12. The number o the horizontal division from the center of the screen was read and
    the voltage and current were written on table 4.1.
    13. The phase angle was determined as the product of the result in procedure 10
    and 12.
    14. The phase angle was calculated and the results were recorded on table 4.1.
    15. The impedance, conductance, susceptance and admittance were calculated and
    written on table 4.1.

    IV. TABULATED DATA AND RESULTS

    Circuit Vi(p) VR3(p) I(p) T N°


    [V] [mV] [mA] [div] degrees
    per
    division
    R-C Series 3 28 2.8 9.7 37.11
    R-C 3 100 10 9.8 36.73
    Parallel
    N° 𝝋 VCI(p) VR1(p) 𝝋
    horizontal measured [V] [V] calculated
    divisions [degrees] [degrees]
    R-C Series 0.1 3.7 0.9 2.8 17.49
    R-C 0.1 3.67 70.56
    Parallel
    Z G B Y
    [Ω] [S] [S] [S]
    R-C Series 1058.97
    R-C 306.496 0.000990 0.00314 0.00329
    Parallel
    Table 9.1
    V. COMPUTATIONS

    𝑅 = 𝑅1 + 𝑅2 1
    𝑋𝐶 =
    2𝜋𝑓𝐶
    𝑅 = 1000𝛺 + 10𝛺
    𝑋𝑐 = [2𝜋(500𝐻𝑧)(1𝑥10−6 𝐹)]−1
    𝑅 = 1010𝛺
    𝑋𝑐 = 318.31𝛺

    Computations for R-C Series:

    𝑉𝑅3(𝑆𝐸𝑅) 𝑋𝐶
    𝐼(𝑝) = 𝜑 = 𝑡𝑎𝑛−1 ( )
    𝑅3 𝑅

    28𝑚𝑉 318.31𝛺
    𝐼(𝑝) = 𝜑 = 𝑡𝑎𝑛−1 ( )
    10𝛺 1010𝛺

    𝐼(𝑝) = 2.8 𝑚𝐴 𝜑 = 17.49°

    𝑍 = √𝑅2 + 𝑋𝐶 2

    𝑍 = √(1010𝛺)2 + (318.31𝛺)2

    𝑍 = 1058.97𝛺

    Computations for R-C Parallel:

    𝑉𝑅3(𝑃𝐴𝑅) 1 1 −1
    𝐼(𝑝) = 𝑍= [ + ] + 𝑅3
    𝑅3 𝑅2 𝑋𝐶2

    100𝑚𝑉 −1
    𝐼(𝑝) = 1
    10𝛺 𝑍 = [ + 2𝜋𝑓𝐶2 ] + 𝑅3
    𝑅2
    𝐼(𝑝) = 10 𝑚𝐴 −1
    1
    𝑍= [ + 𝑗2𝜋(500𝐻𝑧)(1𝑥10−6 𝐹)] +10Ω
    1000𝛺

    1
    𝐺= 𝑍 = 306.496𝛺 ∠ 70.56°
    𝑅
    𝑍 = 306.496𝛺
    1
    𝐺=
    1010𝛺
    𝜑 = 70.56°
    −4
    𝐺 = 9.90𝑥10 𝑆

    1 1 1
    𝐵= 𝑌= + 𝑗
    𝑋𝐶 𝑅 𝑋𝐶2

    1 1 1
    𝐵= 𝑌= +𝑗
    318.31𝛺 1010𝛺 318.31𝛺

    𝐵 = 3.14𝑥10−3 𝑆 𝑌 = 3.29𝑥10−3 𝑆
    VI. GRAPH
    VII. INTERPRETATION OF DATA AND RESULTS

    VIII. CONCLUSION

    IX. CONTRIBUTIONS

    ALARBA, PEDROCHE N. Graph , Interpretation Data and Result


    BALASBAS, HANNAHZEL G. Computations, Contribution
    CABESAS, MARK ANTHONY E. Electrical Diagrams, Procedure
    CAM, LEX MARION D. Objectives , Instruments and
    Component
    CATINGUB, KANDACE THEA C. Tabulated Data and Result, Conclusion

    You might also like