Terrasat IBUC 2 IBUC 2e IBUC 2G IBUC R IBUC G Operations Manual - Terrasat Communications

Engineered to Endure
Cyber Hardened Intelligent Block

Upconverter
IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC G
Operations Manual
24-Hour Technical Support Phone: +1 669.258.9740

e-mail: [email protected]
This document is provided to customers who have purchased Terrasat Communications, Inc.
equipment. This document is copyright protected and no part of this manual may be reproduced,
transcribed, or translated into any language or transmitted in any form whatsoever without the
prior written consent of Terrasat Communications, Inc.
Technical information contained in this publication is for reference purposes only and is subject
to change without notice. Every effort has been made to supply complete and accurate
information; however, Terrasat Communications, Inc. assumes no responsibility and will not be
liable for any errors, omissions, damage, or loss that might result from any use or misapplication
of this manual or the information contained therein (even if this information is properly followed
and problems still arise).
Part Number: O&M-22062-0003

Manual’s Version / Revision: C
© September 2021 Terrasat Communications, Inc.
315 Digital Drive Phone: +1 408.782.5911

Morgan Hill, CA 95037 FAX: +1 408.782.5912
www.terrasatinc.com
TABLE OF CONTENTS
PREFACE
Conventions and References .................................................................................................... P-1
Cautions and Warnings ..................................................................................................... P-2
Trademarks........................................................................................................................ P-2
Electrical Safety Notice .................................................................................................... P-2
Chapter 1, Introduction
Our Intelligent Block Upconverters, the IBUC........................................................................ 1-1
Our Cyber Hardened IBUC...................................................................................................... 1-2
Reference Documents .............................................................................................................. 1-3
Warranty Information............................................................................................................... 1-6
Chapter 2, Functional Description

Introduction .............................................................................................................................. 2-1
System Components................................................................................................................. 2-2
DC Supply............................................................................................................................ 2-8
AC Supply............................................................................................................................ 2-8
Fuses..................................................................................................................................... 2-13
Monitor and Control............................................................................................................. 2-15
RF Signal Flow .................................................................................................................... 2-16
Software ............................................................................................................................... 2-22
System Configurations......................................................................................................... 2-23
Storage Information ............................................................................................................. 2-28
Chapter 3, Installation
Introduction .............................................................................................................................. 3-1
General Requirements .............................................................................................................. 3-1
Unpacking ......................................................................................................................... 3-1
Furnished Items................................................................................................................. 3-2
Accessories........................................................................................................................ 3-3
Installing the ODU ............................................................................................................... 3-3
Tools.................................................................................................................................. 3-3
Test Equipment ................................................................................................................. 3-3
Site Considerations ........................................................................................................... 3-4
Mounting Considerations.................................................................................................. 3-4
Power Requirements ......................................................................................................... 3-5
Grounding ......................................................................................................................... 3-7
Antenna Recommendations .............................................................................................. 3-7
Antenna Mounting ............................................................................................................ 3-8
i
System Pressurization ....................................................................................................... 3-12

System Cabling Requirements.......................................................................................... 3-13
Cable and Waveguide Connections .................................................................................. 3-18
Basic System Alignment...................................................................................................... 3-20
Setting the Tx and Rx Frequencies ................................................................................... 3-21
Transmit Power Alignment............................................................................................... 3-21
Transmit RF Output Adjustment with Modem or Converter (70 MHz to L-band).......... 3-22
Final Checks............................................................................................................................. 3-23
Chapter 4, Operations
Introduction.............................................................................................................................. 4-1
Start-up Checklist..................................................................................................................... 4-1
Turning On the IBUC .......................................................................................................... 4-2
Setting Operating Parameters .............................................................................................. 4-2
Setting the Tx Frequency (L-band)................................................................................... 4-4
Setting Alarm Thresholds ................................................................................................. 4-4
Configuring Alarm States ................................................................................................. 4-5
Configuring ALC/AGC .................................................................................................... 4-5
Configuring the External Mute ......................................................................................... 4-6
Common Errors........................................................................................................................ 4-7
LED is Red........................................................................................................................ 4-7
No Power to the Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G . 4-7
Time Stamp Data is Incorrect ........................................................................................... 4-8
Satellite Network Operations Center Doesn’t Recognize Signal ..................................... 4-8
Transmit Power in Saturation ........................................................................................... 4-9
Tx Input/Output Level Verification.................................................................................. 4-9
Chapter 5, Monitor and Control Features

Introduction.............................................................................................................................. 5-1
M&C Interfaces........................................................................................................................ 5-1
RS232................................................................................................................................... 5-1
Multifunction LED .............................................................................................................. 5-2
Ethernet................................................................................................................................ 5-3
Determining the IP Address of Your IBUC...................................................................... 5-4
SSHv2 ............................................................................................................................... 5-4
SNMPv3............................................................................................................................ 5-5
Embedded Web Pages ...................................................................................................... 5-8
Power Measurement................................................................................................................. 5-8
Input Power Overdrive Protection ....................................................................................... 5-9
Chapter 6, Troubleshooting
Maintenance ............................................................................................................................. 6-1
Transceiver Fault Isolation .................................................................................................. 6-1
AC Power Problems/Conditioning ................................................................................... 6-1
ii
Site-Related Problems....................................................................................................... 6-2

M&C Checks .................................................................................................................... 6-2
Power Supply Checks ....................................................................................................... 6-3
Transmit Power Setting .................................................................................................... 6-3
Common Problems .............................................................................................................. 6-5
Tx Output is Disabled ....................................................................................................... 6-5
Incorrect Frequency Settings ............................................................................................ 6-5
Damaged Cables ............................................................................................................... 6-5
10 MHz Reference Signal is at the Wrong Level or Missing ........................................... 6-6
Antenna is Pointed Toward Wrong Satellite or is Misaligned ......................................... 6-6
Moisture Migrated Into the Cyber Hardened IBUC ......................................................... 6-7
Bad Orthogonal Mode Transducer and/or Antenna.......................................................... 6-7
LED is Red........................................................................................................................ 6-7
Repair Policy............................................................................................................................ 6-8
Returned Material Authorization (RMA) ............................................................................ 6-8
Appendix A, Part Numbering Schema

Identifying the Part and Serial Numbers.................................................................................. A-1
Decoding the Part Number....................................................................................................... A-1
Appendix B, Embedded Web Pages

Introduction .............................................................................................................................. B-1
Web Pages Menu Tree ............................................................................................................. B-5
Log In................................................................................................................................ B-5
Responsive Design............................................................................................................ B-6
Configuration Menu............................................................................................................. B-7
Information ....................................................................................................................... B-7
User Configuration ........................................................................................................... B-9
Transmit Configuration..................................................................................................... B-10
Interface Configuration..................................................................................................... B-14
System Configuration ....................................................................................................... B-15
Alarm Configuration......................................................................................................... B-18
Configuration File............................................................................................................. B-21
Status Menu ......................................................................................................................... B-22
Alarms............................................................................................................................... B-22
Sensors .............................................................................................................................. B-25
Event Log.......................................................................................................................... B-26
Charts Menu...................................................................................................................... B-27
SNMP Menu ........................................................................................................................ B-28
SNMP User Configuration................................................................................................ B-28
SNMP versions and Cyber Security envolved.................................................................. B-29
SNMP Views .................................................................................................................... B-29
SNMP Traps ..................................................................................................................... B-31
SNMP Trap Notifications Filters ...................................................................................... B-33
SNMP Groups................................................................................................................... B-34
iii
Appendix C, ASCII Command/Response Structure

Cyber Hardened IBUC Console and SSHv2 Command Set.................................................... C-1
ADU.................................................................................................................................. C-3
ATL................................................................................................................................... C-5
C10.................................................................................................................................... C-5
CAS................................................................................................................................... C-6
CBT................................................................................................................................... C-7
CCF................................................................................................................................... C-7
CCM.................................................................................................................................. C-8
CCS................................................................................................................................... C-8
CFD................................................................................................................................... C-9
CIA.................................................................................................................................... C-9
CIC.................................................................................................................................... C-10
CID.................................................................................................................................... C-11
CIE .................................................................................................................................... C-11
CIG.................................................................................................................................... C-12
CIHA................................................................................................................................. C-12
CIHD................................................................................................................................. C-13
CIM................................................................................................................................... C-14
CIS .................................................................................................................................... C-14
CLE................................................................................................................................... C-15
CM1 .................................................................................................................................. C-16
CM2 .................................................................................................................................. C-17
CMS .................................................................................................................................. C-18
COI.................................................................................................................................... C-19
COX .................................................................................................................................. C-20
CPL ................................................................................................................................... C-20
CPS ................................................................................................................................... C-21
CRT................................................................................................................................... C-21
CSF ................................................................................................................................... C-22
CTI .................................................................................................................................... C-22
CTM.................................................................................................................................. C-23
CTV .................................................................................................................................. C-23
CVD .................................................................................................................................. C-24
CZZ................................................................................................................................... C-24
DLU .................................................................................................................................. C-25
DRO .................................................................................................................................. C-25
DTM.................................................................................................................................. C-26
EHI.................................................................................................................................... C-27
EHZ................................................................................................................................... C-27
HLP................................................................................................................................... C-28
ISSUE ............................................................................................................................... C-28
NTP................................................................................................................................... C-29
NTPDEL ........................................................................................................................... C-29
SGA .................................................................................................................................. C-30
SGD .................................................................................................................................. C-30
iv
SHL ................................................................................................................................... C-31

SHP ................................................................................................................................... C-32
SHZ ................................................................................................................................... C-32
SNA .................................................................................................................................. C-34
SND .................................................................................................................................. C-35
STA ................................................................................................................................... C-36
STD ................................................................................................................................... C-37
SUA .................................................................................................................................. C-38
SUD .................................................................................................................................. C-39
SVA .................................................................................................................................. C-40
SVD .................................................................................................................................. C-41
TAH .................................................................................................................................. C-41
TAL................................................................................................................................... C-42
TAS ................................................................................................................................... C-42
TAZ................................................................................................................................... C-43
TBH .................................................................................................................................. C-43
TBL ................................................................................................................................... C-44
TBT ................................................................................................................................... C-44
TDT................................................................................................................................... C-45
TFB ................................................................................................................................... C-46
TFI .................................................................................................................................... C-47
TFR ................................................................................................................................... C-47
TGC .................................................................................................................................. C-48
TGL................................................................................................................................... C-49
TGR .................................................................................................................................. C-49
TPB ................................................................................................................................... C-50
TPM .................................................................................................................................. C-50
TPO ................................................................................................................................... C-51
TPT ................................................................................................................................... C-51
TSD ................................................................................................................................... C-52
TSP.................................................................................................................................... C-52
TST ................................................................................................................................... C-53
TTS ................................................................................................................................... C-54
TTT ................................................................................................................................... C-54
TZO................................................................................................................................... C-55
Other Kinds of Commands & Queries................................................................................. C-55
CTRL + C ......................................................................................................................... C-55
CTRL + D ......................................................................................................................... C-55
Enable CTRL + Shift + V / C in Windows Command Prompt ........................................ C-56
List of Commands & Queries Not Supported on SNMP Versions v1 and v2..................... C-56
Appendix D, Component Specifications and Reference Drawings

Reference Drawings ................................................................................................................. D-1
Data Sheets............................................................................................................................... D-7
v
Appendix E, Firmware Upgrade

Update Procedure..................................................................................................................... E-1
How to Update step by step .............................................................................................. E-2
Appendix F, Glossary
Glossary of Terms.................................................................................................................... F-1
vi
LIST OF TABLES
Table P.1 Typographical Conventions ........................................................................................ P-1

Table 1.1 Satellite Operation Standards...................................................................................... 1-2
Table 2.1 IBUC 2 Transmit Frequency Plans............................................................................. 2-3
Table 2.2 IBUC 2e Transmit Frequency Plans ........................................................................... 2-4
Table 2.3 IBUC 2G Transmit Frequency Plans ......................................................................... 2-5
Table 2.4 IBUC R Transmit Frequency Plans............................................................................ 2-6
Table 2.5 IBUC G Transmit Frequency Plans........................................................................... 2-7
Table 2.6 AC Supply Operating Voltage Ranges ....................................................................... 2-8
Table 2.7 Fuse Markings............................................................................................................. 2-13
Table 2.8 External 10 MHz Reference Signal Parameters.......................................................... 2-16
Table 2.9 Internal 10 MHz Reference Signal Parameters........................................................... 2-16
Table 2.10 Basic System Requirements........................................................................................ 2-23
Table 3.1 Recommended Test Equipment .................................................................................. 3-3
Table 3.2 Terrasat Outdoor Power Supplies ............................................................................... 3-6
Table 3.3 Interface Connector Schedule ..................................................................................... 3-13
Table 3.4 Pin Assignments for M&C Interface Connector J2 .................................................... 3-15
Table 3.5 Pin Assignments for DC Power Connector J3 ............................................................ 3-16
Table 3.6 Pin Assignments for AC Power Connector J3 ............................................................ 3-16
Table 3.7 Pin Assignments for Milspec High-Power AC Connector J3..................................... 3-17
Table 3.8 Pin Assignments for Ethernet Connector J4 ............................................................... 3-17
Table 5.1 Default Alarm Configuration ...................................................................................... 5-3
Table 6.1 Possible Scenarios for IBUCs with an External 10 MHz Reference Signal............... 6-6
Table B.1 Default Values for Power Monitor Frequency............................................................ B-11
Table B.2 Default Values for Burst Threshold ............................................................................ B-12
Table C.1 Error Response Table.................................................................................................. C-1
Table C.2 Alarm Mask ................................................................................................................ C-6
Table C.3 Configurable Alarm Mask .......................................................................................... C-16
Table C.4 Default Values for the TAH, TAL, and TBT Commands .......................................... C-45
Table C.5 Band Numbering ......................................................................................................... C-46
Table C.6 Default Values for the TFR Command ....................................................................... C-48
vii
viii
LIST OF FIGURES
Figure 2.1 Front Panel of a Low Energy Consumption IBUC 2e................................................... 2-9
Figure 2.2 Front Panel of a DC-powered IBUC 2 ............................................................................. 2-10
Figure 2.3 Front Panel of an AC-powered IBUC 2G ................................................................. 2-11
Figure 2.4 Front Panel of an AC-powered IBUC G using MilSpec connector.......................... 2-12
Figure 2.5 IEC 127 Compliant Fuse Marking ............................................................................. 2-15
Figure 2.6 DC-powered Low-Power Cyber Hardened IBUC Functional Circuit Block Diagram 2-
19
Figure 2.7 DC-powered Cyber Hardened IBUC Functional Circuit Block Diagram ................. 2-20
Figure 2.8 AC-powered Cyber Hardened IBUC Functional Circuit Block Diagram ................. 2-21
Figure 2.9 DC Low Power IBUC System Configuration............................................................ 2-25
Figure 2.10 DC Power IBUC System Configuration .................................................................... 2-26
Figure 2.11 AC Power IBUC System Configuration .................................................................... 2-27
Figure 3.1 Furnished items with Cyber Hardened IBUC 2 ......................................................... 3-2
Figure 3.2 IBUC 2 Field Installation ........................................................................................... 3-9
Figure 3.3 IBUC 2 Installation .................................................................................................... 3-10
Figure 3.4 Location of Mounting Holes ...................................................................................... 3-11
Figure 3.5 IBUC In Line Mounting Configuration ..................................................................... 3-11
Figure 3.6 Location of Adjustment Slots on Optional Mounting Bracket .................................. 3-12
Figure 3.7 Connector J1 Caution Symbol ................................................................................... 3-14
Figure 3.8 Applying the Anti-Seize Lubricant ............................................................................ 3-19
Figure 3.9 Waveguide Label and Channel for Gasket ................................................................ 3-20
Figure A.1 Identifying the Part and Serial Numbers.................................................................... A-1
Figure A.2 Part Numbering Schema for Cyber Hardened IBUC................................................. A-2
Figure A.3 Part Numbering Schema for Cyber Hardened IBUC with PSUI Systems................. A-3
Figure B.1 Ethernet Properties Window ...................................................................................... B-2
Figure B.2 Choosing the Internet Protocol (TCP/IP) Properties ................................................. B-3
Figure B.3 Host IP Address Configuration .................................................................................. B-4
Figure B.4 Login Tab................................................................................................................... B-5
Figure B.5 Mobile view of the Embedded Web Pages ................................................................ B-6
Figure B.6 Information Page........................................................................................................ B-7
Figure B.7 Cyber Hardened IBUC Users..................................................................................... B-9
Figure B.8 Add Cyber Hardened IBUC User .............................................................................. B-9
Figure B.9 Delete Cyber Hardened IBUC User........................................................................... B-10
Figure B.10 Tx Configuration Tab ................................................................................................ B-10
Figure B.11 Interface Configuration Tab....................................................................................... B-14
Figure B.12 System Configuration Tab ......................................................................................... B-15
Figure B.13 Alarm Configuration Tab........................................................................................... B-18
Figure B.14 Configuration File page ............................................................................................. B-21
Figure B.15 Alarm Status Tab ....................................................................................................... B-22
Figure B.16 Sensor Tab ................................................................................................................. B-25
Figure B.17 Event Log................................................................................................................... B-26
ix
Figure B.18 Statistics Charts ......................................................................................................... B-27

Figure B.19 SNMP Users .............................................................................................................. B-28
Figure B.20 SNMP User Add ........................................................................................................ B-29
Figure B.21 SMP User Delete ....................................................................................................... B-29
Figure B.22 SNMP Views ............................................................................................................. B-30
Figure B.23 SNMP Views Add ..................................................................................................... B-30
Figure B.24 SNMP Views Delete.................................................................................................. B-30
Figure B.25 SNMP Trap Sessions ................................................................................................. B-32
Figure B.26 SNMP Trap Session Add........................................................................................... B-32
Figure B.27 SNMP Notifications & Filter..................................................................................... B-33
Figure B.28 Adding Notifications & Filters .................................................................................. B-33
Figure B.29 SNMP Groups............................................................................................................ B-34
Figure B.30 Add SNMP Groups.................................................................................................... B-35
Figure B.31 Delete SNMP Groups ................................................................................................ B-35
Figure C.1 Login as ‘xxxx’ (Admin user) showing ADU Query and Command execution. ..... C-4
Figure D.2 Fabrication Drawing, FBD-21012-XXXX, Rev A.................................................... D-2
Figure D.3 Fabrication Drawing, FBD-21984-XXXX, Rev B, page 1 of 2 ................................ D-3
Figure D.4 Fabrication Drawing, FBD-21984-XXXX, Rev B, page 2of 2 ................................. D-4
Figure D.5 Fabrication Drawing, FBD-20606-XXXX, Rev A.................................................... D-5
Figure D.6 Example Installation Drawing, IND-10521-0011, Rev A......................................... D-6
Figure E.1 Firmware Upgrade File.............................................................................................. E-3
Figure E.2 Software Update Web Page ....................................................................................... E-3
Figure E.3 Software Update progress.......................................................................................... E-4
Figure E.4 Software Update Wait for Reboot ............................................................................. E-5
x
REVISION HISTORY
Revision Date Description
August,06th
A Initial Public Release
2020
Added Appendix B, Embedded Web Pages

October, 09th
B Updated Appendix C, ASCII Command Response Structure
2020
Added Appendix E, Firmware Upgrade
Included updates and new safety features (Cyber Hardened)
Updated Firmware and web pages versions and features
Updated Copyright terms and terms of use
Updated Introduction chapter
Updated Functional Description chapter, and images such as: Functional diagrams.
Updated Installation chapter
Updated Operation chapter

September, 24th
C Updated Chapter Monitor & Control chapter: Added new features and also,
2021
discontinued some other features.
Updated Troubleshooting chapter
Updated Appendix A, Part Numbering Schema
Updated Appendix B, Embedded Web Pages
Updated Appendix C, ASCII Command Response Structure
Updated Glossary
Added new Caution, Warning, notes, attention, and disclaimer signs throughout the
chapters for a better user experience.
xi
xii
P
P REFACE
This manual provides information about the Terrasat Communications, Inc. line of
cyber hardened intelligent block upconverters.
Conventions and References

Before you start using this manual, it is important to understand the typographical
conventions and terms used in the documentation.
Table P.1 describes typographical conventions used in Terrasat Communications, Inc.

documentation. For definitions of specialized terms used in the documentation, see
Appendix F, Glossary.
Table P.1 Typographical Conventions

Convention Description/Example
Used to emphasize the importance of a point.
Emphasis
The IP Address must be a unique number.
References to a section in the same document are marked in blue and
are hyperlinked.
Internal cross-references
See Warranty Information on page 1-5.
Named Terrasat products and features are identified on first use.
Product and feature
names
...line of intelligent block upconverters (IBUCs).
References to other Terrasat publications. If the reference is hyperlinked,
it is also underscored.
Technical Publication
References
For detailed information, see the Terrasat Communications, Inc. IBUC
Operations Manual.
A special font marks text that you type.
User-entered values
At the password prompt, type MyPassword.
Cautions and Warnings
! CAUTION
CAUTION indicates a call for attention to potential risk or situation that, if
not avoided, could result in minor or moderate injury or damage. It may
also indicate other unsafe practices or risks of property damage.
HIGH-VOLTAGE
HIGH VOLTAGE indicates the presence of a high-voltage hazard.
! WARNING
WARNING indicates a potentially hazardous situation that, if not avoided,
could result in death or severe injury.
Trademarks
Terrasat Communications Inc. is a registered trademark. Also, other product names
mentioned in this manual may be trademarks or registered trademarks of their
respective companies and are hereby acknowledged.
Electrical Safety Notice

This equipment has been designed to minimize exposure of personnel to hazards. All
operators and technicians must:
• Know how to work around, with, and on high-voltage equipment.

• Exercise every precaution to ensure safety of personnel.
• Exercise extreme care when working near high voltages.
• Be familiar with the warnings in this manual.
P-2 | Preface
1
C HAPTER
INTRODUCTION
CHAPTER1
This manual is intended for users of Terrasat Communications, Inc. block upconverter
systems including the Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R and
IBUC G. It contains information about
• Installation, operation, and maintenance of Cyber Hardened IBUC 2, IBUC 2e,

IBUC 2G, IBUC R and IBUC G systems.
• Use of user interface protocols for remote monitor and control capabilities.
Our Intelligent Block Upconverters, the IBUC

The term “intelligent” block upconverter (IBUC) refers to the advanced features and
monitor and control capabilities of the entire line of Terrasat IBUC models. Each
IBUC model includes automatic gain control (AGC) and automatic level control
(ALC) features as well as internal diagnostics. Terrasat’s IBUCs also provide
extensive M&C (Monitoring and Control) features through software commands and
alarms, providing access to the numerous operating parameters and features available
in the unit. Access to features and M&C functions is provided via several methods
including RS232, SSHv2, UDP (SNMPv3) and TCP/IP (HTTPS). Each IBUC model
is also fitted with a multifunction LED for visual status indications.
Our Cyber Hardened IBUC

The Cyber Hardened IBUCs bring a new and safer future to Satellite Communications.
These are devices essentially meant for high-security systems intended to operate
connected to Cyberspace.
The Cyber Hardened product is a new high-end safety feature for our units. Its
embedded high-end protocols solve all the security problems related to any typical
Ethernet device. It is called "Hardened" due to the added security features, making the
system considerably harder to break on an eventual cyber invasion attempt. The vast
majority of the other protocols traditionally used for all kinds of purposes throughout
the globe and even other industries are easier to break.
Our Cyber Hardened units have embedded layers of encryption and authentication
protocols. That means even if someone invades the system and could eventually
manage to read the transferred information inside the wires during the transfers, that
kind of misuser won't understand that data since we now have more encryption layers
even inside the cables. Therefore, data such as passwords and user information are
more secure than ever.
Since data protection and security are essential and demand constant renovation, we
present our Cyber Hardened Units.
1-2 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Introduction
Reference Documents
Use the satellite operation standards listed in Table 1.1 as reference documents.
Table 1.1 Satellite Operation Standards

Earth Station Standards
Performance Characteristics for Intermediate Data Rate Digital
Intelsat IESS 308/309
Carriers Using Convolutional Encoding and QPSK Modulation
Minimum Technical and Operational Requirements for Earth Stations
Eutelsat EESS 502 Transmitting to a Eutelsat Transponder for Non-Standard Structured
Types of SMS Transmissions. Standard M.
Radio (and Telecommunications Terminal) Equipment Directive
2014/53/EU
(RED/RTTE)
Satellite Earth Stations and Systems (SES); Harmonised Standard for
Very Small Aperture Terminal (VSAT); Transmit-only, transmit-and-
ETSI EN 301 443 v2.1.1
receive, receive-only satellite earth stations operating in the 4 GHz
(2016-05)
and 6 GHz frequency bands covering the essential requirements of
article 3.2 of the Directive 2014/53/EU
Satellite News Gathering Transportable Earth Stations (SNG TES)
ETSI EN 301 430 V2.1.1
operating in the 11 GHz to 12 GHz/13 GHz to 14 GHz frequency
(2016-05)
bands covering the essential requirements of article 3.2 of the
Directive 2014/53/EU
Very Small Aperture Terminal (VSAT); Transmit-only, transmit/receive
ETSI EN 301 428 V2.1.2
or receive-only satellite earth stations operating in the 11/12/14 GHz
(2017-05)
frequency bands covering the essential requirements of article 3.2 of
the Directive 2014/53/EU
Satellite Interactive Terminals (SIT) and Satellite User Terminals
ETSI EN 301 360 V2.1.1
(SUT) transmitting towards satellites in geostationary orbit, operating
(2016-06)
in the 27,5 GHz to 29,5 GHz frequency bands covering the essential
requirements of article 3.2 of the Directive 2014/53/EU
Satellite Interactive Terminals (SIT) and Satellite User Terminals
ETSI EN 301 459 V2.1.1
(SUT) transmitting towards satellites in geostationary orbit, operating
(2016-05)
in the 29,5 GHz to 30,0 GHz frequency bands covering the essential
requirements of article 3.2 of the Directive 2014/53/EU
Interoperability of Super High Frequency (SHF) Satellite
MIL-STD-188-164C
Communications Terminals.
ANSI/TIA/EIA 568 Commercial Building Telecommunications Cabling Standard
Environmental Standards
Equipment Engineering (EE): Environmental Conditions and
ETS 300 019-1-1 Environmental Tests for Telecommunications Equipment. Part 1-1:
Classification of environmental conditions. Storage.
Classification of environmental conditions. Transportation.
Reference Documents | 1-3

Table 1.1 Satellite Operation Standards (Continued)

Environmental Tests for Telecommunications Equipment. Part 1-4:
ETS 300 019-1-4
Classification of environmental conditions. Stationary use at non-
weather protected locations.
Specification of environmental tests; Storage
ETS 300 019-2-2 Environmental Tests for Telecommunications Equipment. Part 2.2:
Specification of environmental tests; Transportation
Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-3:
ETS 300 019-2-3
Specification of environmental tests; Stationary use at weather
protected locations
Environmental Tests for Telecommunications Equipment. Part 2-4:
ETS 300 019-2-4
Specification of environmental tests; Stationary use at non-weather
protected locations
MIL-STD-810G Environmental Engineering Considerations and Laboratory Tests.
2011/65/EU Restriction of the use of certain hazardous substances (RoHS)
Technical documentation for the assessment of electrical and
EN IEC 63000:2008 electronic products with respect to the restriction of hazardous
substances
Amending Annex II to Directive 2011/65/EU of the European
2015/863 Parliament and of the Council as regards the list of restricted
substances
EMC/EMI Standards
2014/30/EU Electromagnetic Compatibility (EMC)
Electromagnetic compatibility of multimedia equipment - Emission
EN 55032:2015/AC:2016-07
requirements
Information technology equipment - Immunity characteristics - Limits
EN 55024:2010/A1:2015
and methods of measurement
Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for
EN 61000-3-2:2014 harmonic current emissions (equipment input current <= 16 A per
phase)
Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of
voltage changes, voltage fluctuations and flicker in public low-voltage
EN 61000-3-3:2013
supply systems, for equipment with rated current <= 16 A per phase
and not subject to conditional connection
Electromagnetic compatibility (EMC) - Part 3-11: Limits - Limitation of
voltage changes, voltage fluctuations and flicker in public low-voltage
EN 61000-3-11:2000
supply systems - Equipment with rated current <= 75 A and subject to
conditional connection
Electromagnetic compatibility (EMC) - Part 3-12: Limits - Limits for
EN 61000-3-12:2011 harmonic currents produced by equipment connected to public low-
voltage systems with input current > 16 A and <= 75 A per phase
Electromagnetic compatibility (EMC) - Part 4-2: Testing and
EN 61000-4-2:2009
measurement techniques - Electrostatic discharge immunity test
Table 1.1 Satellite Operation Standards (Continued)

EN 61000-4-3:2006/A2:2010 measurement techniques - Radiated, radio-frequency,
electromagnetic field immunity test
EN 61000-4-4:2012
measurement techniques - Electrical fast transient/burst immunity test
EN 61000-4-5:2014/A1:2017
measurement techniques - Surge immunity test
EN 61000-4-6:2014/
measurement techniques - Immunity to conducted disturbances,
AC:2015
induced by radio-frequency fields
EN 61000-4-11:2004/
measurement techniques - Voltage dips, short interruptions and
A1:2017
voltage variations immunity tests
EN 61000-4-34:2007/ measurement techniques - Voltage dips, short interruptions and
A1:2009 voltage variations immunity tests for equipment with mains current
more than 16 A per phase
Electromagnetic compatibility and Radio spectrum Matters (ERM);
ETSI EN 301 489-1 V1.9.2
Electromagnetic Compatibility (EMC) standard for radio equipment
(2011-09)
and services; Part 1: Common technical requirements
Electromagnetic compatibility and Radio spectrum Matters (ERM);
Electromagnetic Compatibility (EMC) standard for radio equipment
ETSI EN 301 489-12 V3.1.1 and services; Part 12: Specific conditions for Very Small Aperture
(2019-04) Terminal, Satellite Interactive Earth Stations operated in the
frequency ranges between 4 GHz and 30 GHz in the Fixed Satellite
Service (FSS)
Requirements for the Control of Electromagnetic Interference
MIL-STD-461G
Characteristics of Subsystems and Equipment
Safety Standards
2014/35/EU Low voltage (LVD)
EN 62368-1:2014/AC:2017- Audio/video, information and communication technology equipment -
03 Part 1: Safety requirements (IEC 62368-1:2014, modified)
Information technology equipment - Safety - Part 22: Equipment
EN 60950-22:2017
installed outdoors
EN 60529:1991/A2:2013/
Degrees of protection provided by enclosures (IP Code)
AC:2019-02
Cyber Security Best Practices

FIPS 140-2 Security Requirements for Cryptographic Modules
Application Security and
Development STIG
Web Server SRG
Network Other Devices
STIG
General Purpose OS STIG
Reference Documents | 1-5

Warranty Information
Determination of warranty status of equipment shall be in accordance with the
following Terrasat Communications, Inc. Warranty Policy.
(A) This warranty is for equipment of Terrasat Communications, Inc. The term
“Terrasat” as used throughout this warranty shall mean Terrasat Communications,
Inc., if the equipment was manufactured by Terrasat Communications, Inc.
(B) Terrasat warrants that its equipment shall be free from defects in material or
workmanship at the time of shipment and that it will conform to applicable
specifications.
For all Satcom products, the buyer shall exercise any and all warranty claims within a
period of thirty-six (36) months.
(1) The warranty does not apply to any part of a product if it has been altered,
repaired, or misused in any way that, in the opinion of Terrasat, affects the
reliability of, or detracts from the performance of, any part of the product; or it is
damaged as a result of the use of such part in or in connection with equipment not
previously approved by Terrasat.
(2) The warranty does not apply to any product or parts thereof if its serial number
or the serial number of any of its parts has been altered, defaced, or removed.
(3) The warranty does not cover damages or losses incurred in transport.
(4) The warranty does not cover replacement or repair necessitated by loss or
damage resulting from cases beyond the control of Terrasat.
(5) The warranty does not include the furnishing of any labor involved or
connected with the removal and/or reinstallation of warranted equipment or parts
on site, or any labor required to diagnose the necessity for replacement or repair.
(6) In no event shall Terrasat be liable to buyer for any indirect, special, or
consequential damages or lost profits arising from the use of the equipment or
products, even if Terrasat has been advised of the possibility thereof, or for any
inability to use them either separated from or in combination with any other
equipment or products.
(C) Terrasat’s warranty, as stated herein, is in lieu of all other warranties, expressed,
implied or statutory, including those of merchantability and fitness for a particular
purpose, and Terrasat neither assumes nor authorizes any person to assume for it any
other obligation or liability to any person in connection with the sale or use of
Terrasat’s products. The buyer shall pass on to any purchaser, lessee, or other user of
Terrasat’s products, the aforementioned warranty and shall indemnify and hold upon
allegations that the buyer, its agents, or employees have made additional warranties or
representations as to product preference or use.
(D) A fixed charge established for each product will be imposed for all equipment
returned for warranty repair and where the cause of failure cannot be identified by
Terrasat.
Note: Warranty seals are designed to break upon internal access. Access to the internal
electronic components without prior written approval will void the warranty.
For more information about returning a product for repair, see Repair Policy on
page 6-8.
Warranty Information | 1-7

2
C HAPTER
FUNCTIONAL DESCRIPTION
CHAPTER2
The Terrasat outdoor unit (ODU) consists of an intelligent block upconverter (Cyber
Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G), power supply unit
(PSUI), and low-noise block converter (LNB) for use in satellite earth stations. The
outdoor equipment is designed to interface directly with an L-band satellite modem.
Introduction
This chapter contains detailed information about the various system components of the
following Cyber Hardened IBUC models:
• IBUC 2: All of the original features of the IBUC but in a smaller, more
cost-effective package that is ideal for applications where compact size, light
weight, and low thermal dissipation are critical factors.
• IBUC 2e: The low energy consumption model of the IBUC 2, intended for use
with modems with limited capacity power supplies and where DC power is
supplied only via coaxial cable.
• IBUC 2G: The compact physical size of the IBUC 2 powered by gallium nitride
(GaN) technology. GaN devices like the IBUC 2G can operate at much higher
temperatures and work at much higher voltages than GaAs devices.
• IBUC R: All of the original features of the larger IBUC package with an RJ45
Ethernet connector.
• IBUC G: Higher power IBUC in large enclosure powered by gallium nitride
(GaN) technology.
System Components
The interfacility link (IFL) between the ODUs and the L-band modem uses 950 MHz
to 2.0 GHz (L-band) as the interface frequency. This approach enables transmission
and reception over the entire satellite band as opposed to a single transponder. The L-
band IFL can also carry associated signals such as 10 MHz and DC voltage which
simplify installation and reduce costs. Terrasat IBUC systems can be used for single
channel per carrier/multiple channels per carrier (SCPC/MCPC), point-to-point, or
point-to-multiple point network applications (such as voice, data, video, or IP
services). The integrated RJ45 connector enables both SNMPv3 and the Embedded
Web Pages for monitor and control purposes. Its smaller form factor and lighter
weight make the Cyber Hardened IBUC 2, IBUC 2e, and IBUC 2G ideal for situations
where mobility is key. These smaller models can be carried in a backpack/case or
mounted on antennas that can be quickly assembled and disassembled. See Figure 2.9
on page 2-25 through Figure 2.11 on page 2-27 for typical equipment configurations.
The Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC G are
available in a variety of frequency bands as listed in Table 2.1 through Table 2.5. The
IBUC houses the IF interface (demux), the upconverter, the monitor and control
(M&C) card, a DC-to-DC converter (if DC powered) and associated circuitry, an AC-
to-DC converter (if AC powered), and a solid state power amplifier (SSPA) assembly.
The IBUC can also house an optional internal 10 MHz reference signal module.
Higher-power IBUCs also have an external cooling fan assembly. The input interface
to the IBUC connects to a 50  or an optional 75  coaxial cable that carries the L-
Band transmit signal. This IFL (interfacility link cable) interface can also carry an
external 10 MHz reference for the oscillator signal band and DC power.
System Components | 2-2

Table 2.1 IBUC 2 Transmit Frequency Plans
Signal Standard C-band Palapa C-band Insat C-band Extended C-band Full C-band
L-band
(Inverting) 950 MHz to 1525 MHz 975 MHz to 1275 MHz 1150 MHz to 1450 MHz 950 MHz to 1750 MHz 975 MHz to 1850 MHz
LO frequency
(Inverting) 7.375 GHz 7.700 GHz 8.175 GHz 7.600 GHz 7.700 GHz
L-band
(Non-Inverting) 950 MHz to 1525 MHz 1125 MHz to 1425 MHz 965 MHz to 1265 MHz 950 MHz to 1750 MHz 950 to 1825 MHz
LO frequency
(Non-Inverting) 4900 MHz 5300 MHz 5760 MHz 4900 MHz 4900 MHz
RF frequency 5.850 GHz to 6.425 GHz 6.425 GHz to 6.725 GHz 6.725 GHz to 7.025 GHz 5.850 GHz to 6.650 GHz 5.850 GHz to 6.725 GHz
5, 10, 15, 20, 25, 30, 40, 50, 5, 10, 15, 20, 25, 30, 40, 50, 5, 10, 15, 20, 25, 30, 40, 50, 5, 10, 15, 20, 25, 30, 40, 50, 5, 10, 15, 20, 25, 30, 40, 50,
Output Power
60, 80 watts 60, 80 watts 60, 80 watts 60, 80 watts 60, 80 watts
Signal X-band Standard Ku-band (Band 1) Full Ku-band (Band 2) Low Ku-band (Band 3)
L-band 950 MHz to 1450 MHz 950 MHz to 1450 MHz 950 MHz to 1700 MHz 950 MHz to 1450 MHz
LO frequency
(Inverting) — — — —
LO frequency
(Non-Inverting) 6.950 GHz 13.050 GHz 12.800 GHz 11.800 GHz
RF frequency 7.900 GHz to 8.400 GHz 14.000 GHz to 14.500 GHz 13.750 GHz to 14.500 GHz 12.750 GHz to 13.250 GHz
4, 8, 12, 16, 20, 25, 30, 40, 4, 8, 12, 16, 20, 25, 30, 40, 4, 8, 12, 16, 20, 25, 30, 40,
Output Power 5, 10, 20, 25, 40, 50, 60 watts
50 watts 50 watts 50 watts
2-3 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Functional Description
Table 2.2 IBUC 2e Transmit Frequency Plans
L-band
LO frequency
L-band
(Non-Inverting) 950 MHz to 1525 MHz 1125 MHz to 1425 MHz 965 MHz to 1265 MHz 950 MHz to 1750 MHz 950 MHz to 1825 MHz
LO frequency
Output Power 5, 10, 20 watts 5, 10, 15, 20 watts 5, 10, 15, 20 watts 5, 10, 15, 20 watts 5, 10, 15, 20 watts
Signal Standard Ku-band (Band 1) Full Ku-band (Band 2) Low Ku-band (Band 3)
L-band 950 MHz to 1450 MHz 950 MHz to 1700 MHz 950 MHz to 1450 MHz
LO frequency
(Inverting) — — —
LO frequency
(Non-Inverting) 13.050 GHz 12.800 GHz 11.800 GHz
RF frequency 14.000 GHz to 14.500 GHz 13.750 GHz to 14.500 GHz 12.750 GHz to 13.250 GHz
Output Power 4, 8, 12, 16 watts 4, 8, 12, 16 watts 4, 8, 12, 16 watts

Table 2.3 IBUC 2G Transmit Frequency Plans
L-band
LO frequency
L-band
(Non-inverting) 950 MHz to 1525 MHz 1125 MHz to 1425 MHz 965 MHz to 1265 MHz 950 MHz to 1750 MHz 950 MHz to 1825 MHz
LO frequency
Output Power 100, 125 watts 100, 125 watts 100, 125 watts 100, 125 watts 100, 125 watts
Signal Standard Ku-band (Band1) Full Ku-band (Band 2) Low Ku-band (Band 3) X-band Ka-band
L-band 950 MHz to 1450 MHz 950 MHz to 1700 MHz 950 MHz to 1450 MHz 950 MHz to 1450 MHz 1000 MHz to 2000 MHz
LO frequency
(Inverting) — — — — —
LO frequency
(Non-Inverting) 13.050 GHz 12.800 GHz 11.800 GHz 6.950 GHz 28.000 GHz
Output Power 50, 80 watts 50, 80 watts 80 watts 100 watts 5, 10, 16, 20, 25, 40 watts
Signal Ka-band Ka-band
L-band 1000 MHz to 1500 MHz 1000 MHz to 2000 MHz

LO frequency
(Inverting) — —
LO frequency
(Non-Inverting) 28.500 GHz 29.000 GHz
RF frequency 29.500 GHz to 30.000 GHz 30.000 GHz to 31.000 GHz
Output Power 5, 10, 16, 20, 25, 40 watts 5, 10, 16, 20, 25, 40 watts
Table 2.4 IBUC R Transmit Frequency Plans
L-band
LO frequency
L-band
LO frequency
100, 125, 150, 175, 200,

Output Power 100, 125, 150, 175, 200 watts 100, 125, 150, 175, 200 watts 100, 125, 150, 175, 200 watts 100, 125, 150, 175, 200 watts
400 watts
Signal X-band Standard Ku-band (Band 1) Full Ku-band (Band 2) Low Ku-band (Band 3)
L-band 950 MHz to 1450 MHz 950 MHz to 1450 MHz 950 MHz to 1700 MHz 950 MHz to 1450 MHz
LO frequency
(Inverting) — — — —
LO frequency
(Non-Inverting) 6.950 GHz 13.050 GHz 12.800 GHz 11.800 GHz
RF frequency 7.900 GHz to 8.400 GHz 14.000 GHz to 14.500 GHz 13.750 GHz to 14.500 GHz 12.750 GHz to 13.250 GHz
Output Power 80, 100, 125, 150, 175 watts 60, 80, 100, 200 watts 60, 80,100, 200 watts 60, 80, 100, 125, 200 watts

Table 2.5 IBUC G Transmit Frequency Plans
L-band
LO frequency
L-band
LO frequency
Output Power 400 watts 400 watts 400 watts 400 watts 400 watts
Signal X-band Standard Ku-band (Band 1) Full Ku-band (Band 2) Low Ku-band (Band 3) Ka-band
L-band 950 MHz to 1450 MHz 950 MHz to 1450 MHz 950 MHz to 1700 MHz 950 MHz to 1450 MHz 1000 MHz to 2000 MHz
LO frequency
(Inverting) — — — — —
LO frequency
(Non-Inverting) 6.950 GHz 13.050 GHz 12.800 GHz 11.800 GHz 28.000 GHz
Output Power 400 watts 150, 200, 300, 400 watts 150, 200, 300, 400 watts 200, 300, 400 watts 5, 10, 16, 20, 25, 40 watts
‘
Signal Ka-band Ka-band
L-band 1000 MHz to 1500 MHz 1000 MHz to 2000 MHz

LO frequency
(Inverting) — —
LO frequency
(Non-Inverting) 28.500 GHz 29.000 GHz
RF frequency 29.500 GHz to 30.000 GHz 30.000 GHz to 31.000 GHz
Output Power 80 watts 80 watts

DC Supply
DC power can be supplied through the N-connector or F-connector of the L-band
input (labeled J1) or through the external power connector (labeled J3). For the high-
power units, DC power is supplied through the six-pin circular connector (labeled J3)
of the DC input. Higher-power units (such as Ku-band 20 watts and higher, C-band 30
watts and higher, X-band 25 watts and higher, or Ka-band 16 watts and higher) cannot
accept DC input through the L-band input connector due to the higher current draw.
Terrasat IBUCs have several supply voltage options. The standard configuration is
48 VDC. However, a 24 VDC option is available for lower power units. Refer to the
datasheets in Appendix D for more information. This choice of 24 VDC or 48 VDC is
available only when the IBUC is ordered and configured at the factory. The operating
voltage range for the 24 VDC option is 20 VDC to 28 VDC. The operating voltage
range for lower-power units with 48 VDC is 37 VDC to 60 VDC. The operating
voltage range for higher power units is 42 VDC to 60 VDC. DC-powered units are
configured at the factory to have floating input.
Terrasat offers the low power, low energy consumption IBUC 2e. These units are DC
powered only via coaxial cable. While lower power versions of the IBUC 2e can
support voltage swings from 18 VDC to 75 VDC, higher power versions can only
support swings from 37 VDC to 60 VDC. More information about the operating
voltage range maximum power consumption for these units can be found in the
datasheet in Appendix D.
AC Supply
Some IBUCs are available with optional AC power, delivered through connector J3,
as seen in Figure 2.3. Table 2.6 lists the voltage ranges for different bands and power
levels.
Table 2.6 AC Supply Operating Voltage Ranges

Voltage Band Watts
100 VAC to 240 VAC C-band 5 watts to 125 watts
200 VAC to 240 VAC C-band 150 watts to 400 watts
100 VAC to 240 VAC X-band 5 watts to 125 watts
200 VAC to 240 VAC X-band 150 watts to 400 watts
100 VAC to 240 VAC Ku-band 4 watts to 125 watts
200 VAC to 240 VAC Ku-band 150 watts to 400 watts
100 VAC to 240 VAC Ka-band 5 watts to 80 watts
Note: The IBUC 2e pictured in Figure 2.1 has a plate covering the connector at J3. This is
because the low energy consumption IBUC 2e is powered only via coaxial cable
through connector J1.
Note: For more information about connector types, breather valve system and mounting
options, refer to sections: System Cabling Requirements on page 3-13, System
Pressurization on page 3-12 and Antenna Mounting on page 3-8 respectively.
Figure 2.1 Front Panel of a Low Energy Consumption IBUC 2e

Note: The IBUC 2 pictured in Figure 2.2 has a N-Type connection at connector J1.
Figure 2.2 Front Panel of a DC-powered IBUC 2
Note: The IBUC 2G pictured in Figure 2.3 has an N-type connector at J1.
Figure 2.3 Front Panel of an AC-powered IBUC 2G

Note: The IBUC G pictured in Figure 2.4 has an MilSpec Hirose connector at J3.
Figure 2.4 Front Panel of an AC-powered IBUC G using MilSpec connector
Fuses
Table 2.7 lists the fuse markings of the fuses required by different AC-powered IBUC
models. Figure 2.5 on page 2-15 defines the international marking schema.
Table 2.7 Fuse Markings
Fuse Markings
Signal Power Level
115 VAC 230 VAC
5W T1.6AL250V T1.6AL250V
10 W T2AL250V T1.6AL250V
15 W T2.5AL250V T1.6AL250V
20 W T3.15AL250V T1.6AL250V
25 W
T4AL250V T2AL250V
30 W
40 W
T5AL250V T2.5AL250V
50 W
60 W T6.3AL250V T3.15AL250V
C-band 80 W T10AL250V T5AL250V
100 W
T12.5AL250V T6.3AL250V
125 W
150 W
175 W N/A T10AL250V
200 W
250 W N/A T12.5AL250V
300 W N/A T15AH500V
400 W N/A T20AH500V
400 W(G) N/A T16AL250V
5W T1.6AL250V T1.6AL250V
10 W T2AL250V T1.6AL250V
20 W T3.15AL250V T1.6AL250V
25 W T4AL250V T2AL250V
40 W
T6.3AL250V T3.15AL250V
50 W
X-band
80 W T10AL250V T5AL250V
100 W T12.5AL250V T6.3AL250V
100 W(G) T8AL250V T4AL250V
125 W T12.5AL250V T6.3AL250V
150 W
N/A T10AL250V
175 W
400 W(G) N/A T12.5AL250V

Table 2.7 Fuse Markings (Continued)

Fuse Markings
Signal Power Level
115 VAC 230 VAC
4W T1.6AL250V T1.6AL250V
8W T2.5AL250V T1.6AL250V
12 W T2.5AL250V T1.6AL250V
16 W T3.15AL250V T1.6AL250V
25 W T5AL250V T2.5AL250V
50 W T10AL250V T5AL250V
Ku-band 50 W(G) T6.3AL250V T3.15AL250V

60 W T12.5AL250V T6.3AL250V
80 W T12.5AL250V T6.3AL250V
80 W(G) T10AL250V T5AL250V
100 W
T16AL250V T8AL250V
125 W
150 W(G) N/A T10AL250V
200 W N/A T20AH500V
200 W(G) N/A T10AL250V
300 W(G)
N/A T20AH500V
400 W(G)
5 W(G) T1.6AL250V T1.6AL250V
10 W(G) T2AL250V T1.6AL250V
16 W(G)
T3.15AL250V T1.6AL250V
20 W(G)
Ka-band
25 W(G) T4AL250V T2AL250V
40 W(G) T6.3AL250V T3.15AL250V
45 W(G) T8AL250V T4AL250V
80 W(G) T10AL250V T5AL250V
Note: (G) marker stands for IBUC models that use GaN technology for power amplification
and required different fuses than regular GaAs amplifiers
Note: For IBUCs that require fuses up to 6.3 A, Terrasat recommends time lag fuse with a
high I2t value. For IBUCs that require fuses greater than 6.3 A, Terrasat recommends
time-delay fuses.
For reference, IBUCs are delivered with one of the following Littelfuse Series fuse:
• Littelfuse 213 Series. (5x20mm time-lag surge withstand glass body cartridge for
medium current ratings)
• Littelfuse 218 Series. (5x20mm time-lag glass body cartridge for high current
ratings)
• Littelfuse FLQ Series. (10x38mm time-delay midget fuse for high voltage, high
current ratings)
• Littelfuse 326 Series. (6.3x32mm Slo-Blo® Fuse with ceramic body construction
for high interrupting and voltage ratings)
• Littelfuse 332 Series. (6.3x32mm Very Fast-Acting fuse for solid-state device
protection)
Figure 2.5 explains the fuse marking schema.
Fuse Element Speed Current Rating Breaking Capacity Voltage Rating

T: Slow Acting (Träge) 3A: 3 Ampere H: High Breaking 250V: 250 Volts or Less
Capacity
L: Low Breaking
Capacity
Figure 2.5 IEC 127 Compliant Fuse Marking
Monitor and Control

Each IBUC is equipped with extensive monitor and control (M&C) capabilities. Use
any of the following methods to access those capabilities:
• Via the J2 connector using RS232. This method requires that a separate cable must
be run and connected to J2.
Figure D.2 on page D-2 contains a drawing for fabricating your own cable.
• Via the J4 connector using TCP/IP. This method requires a separate Ethernet
cable.
Figure D.3 on page D-3 contains a drawing for fabricating your own cable.

RF Signal Flow
L-band input to the IBUC is through the input N-connector or the F-connector (labeled
J1). Required inputs include an L-band signal at -20 dBm or less and a 10 MHz sine
wave reference signal between +5 dBm and -12 dBm (for those units that do not have
the optional internal 10 MHz reference signal).
The US National Institute of Standards and Technology defines single sideband (SSB)
phase noise as the ratio of the spectral power density measured at an offset frequency
from the carrier to the total power of the carrier signal. The most generally used phase
noise unit of measure has been the single sideband power within a one hertz
bandwidth at a frequency f away from the carrier referenced to the carrier frequency
power. This unit of measure is represented as L (f) in units of dBc/Hz. An internal
phase-locked Local Oscillator provides excellent phase noise when locked to an
external 10 MHz reference. Single sideband phase noise using an external reference
signal is listed in Table 2.8.
Table 2.8 External 10 MHz Reference Signal Parameters

Condition External Reference
10 Hz -115 dBc/Hz
100 Hz -140 dBc/Hz
1 kHz -150 dBc/Hz
10 kHz -155 dBc/Hz
100 kHz n/a
1 MHz n/a
The internal 10 MHz reference signal meets the minimum phase noise requirements
listed in Table 2.9.
Note: If an external 10 MHz reference signal is applied to a unit with the optional internal
10 MHz reference signal, the external signal has priority. When the external signal is
removed from such units, the system automatically reverts to the internal 10 MHz
signal, requiring no additional user input.
Table 2.9 Internal 10 MHz Reference Signal Parameters
Minimum Maximum Condition

-125 dBc/Hz 10 Hz
-145 dBc/Hz 100 Hz
Phase Noise
-160 dBc/Hz 1 kHz
-165 dBc/Hz 10 kHz
Table 2.9 Internal 10 MHz Reference Signal Parameters
Minimum Maximum Condition

Frequency Stability vs. Operating
Temperature Range -30 ppb +30 ppb -40 °C to +85 °C
(referenced to frequency at +25 °C)
Tuning Range
±1 ppm ±1 ppm
(referenced to nominal frequency)
Tuning Slope Positive
Input to the IBUC also includes AC or DC voltage (via the J3 connector) and DC
voltage for low-power units. The input (L-band, 10 MHz, and DC via coaxial cable) is
routed to the demultiplexer circuitry where the various signals are split off and routed
to the appropriate circuits within the IBUC. (Only IBUCs with direct DC or AC via the
J3 connector feed the power supply directly.) The input voltage from the
demultiplexer circuitry is routed to the power supply and the FSK signal is routed to
the M&C card.
The external 10 MHz reference signal is routed to the multiplier circuitry where its
level is first detected and an alarm issued if the signal is low. However, if the signal
level is low and the system is equipped with the optional internal 10 MHz signal, the
system will automatically switch to the internal 10 MHz signal. The 10 MHz signal is
then multiplied to the frequency used for phase-locking purposes. The output of the
multiplier is routed to the phase detector circuitry where it is compared with the phase
of the DRO (dielectric resonator oscillator) signal sample and consequently generates
a voltage that is applied as a control voltage to the DRO to adjust its frequency. The
DRO has been optimized for phase noise at a single frequency based on the frequency
band of that particular IBUC. The output of the DRO is amplified and routed to the
mixer.
The L-band signal that is split off in the demultiplexer circuitry is first filtered and a
sample of it detected for input power detection and control purposes. The signal is then
amplified, and goes through a variable attenuator. The attenuation is used to provide
an attenuation adjustment of 30 dB in 0.1 dB steps and to provide automatic level
control (ALC) or automatic gain control (AGC).
After additional amplification and filtering, the signal is routed to the mixer. The
L-band signal is then mixed with the DRO signal to “upconvert” to the appropriate RF
signal based on the frequency band of the IBUC. The RF signal is filtered, amplified,
and then routed to the temperature compensation circuitry. The temperature
compensation circuitry has been calibrated so that the IBUC gain does not vary more
than 3 dB at any given frequency.
Note: Some units can vary up to 4 dB at any given frequency.
The signal is then routed through an isolator to the solid-state power amplifier (SSPA).
Some models have an additional mechanical filter between the isolator and the SSPA.
The SSPA amplifies the signal which is then routed to the output through an isolator
for reverse power protection. The RF output is detected for M&C purposes. The IBUC
gain has been calibrated so that at minimum attenuation, a -30 dBm input results in
rated power of at least P1dB at the output at any frequency or temperature, for GaAs
units. For GaN units the IBUC gain has been calibrated so that at minimum
attenuation, the small signal gain is, at a minimum, (PSAT+31)dB.
To operate at lower power levels, reduce the input to the IBUC or reduce the IBUC
gain by using the variable attenuator, accessible using any of the M&C interfaces. The
output of a C-band IBUC is a CPR137G waveguide or an N-type connector, the output
of an X-band is a CPR112G waveguide, the output of a Ku-band IBUC is a WR75
cover with groove waveguide, and the output of a Ka-band IBUC is a WR28 UG cover
with groove waveguide.
Figure 2.6 depicts the signal flow for units that are DC powered, Figure 2.7 depicts the
signal flow for units that are AC powered, and Figure 2.8 depicts the signal flow for
DC-powered low energy-consumption units.

Monitor & Control (M&C)

RS232
J2
Alarm
Switch Control
FAN
J4
TCP/IP DC/DC
DC/DC
C/ DC All
Power Supply Circuits
Internal
10MHz
VDC
M&C
M&
&C
External
10MHz Detector
De
ete
tect
ctor
ct Multiplier
Multip
plier
PL
LDDRO
RO
O
De-Mux
VDC
M&C
M&
&C M&C
M
M&C
J1
External 10MHz
L-Band
RF OUT
Gainn Temp
p
Detector ALC/AGC SSPA Detector
or
Adjjustt
Ad
Adjust Comp
M&C M&C M&C
Figure 2.6 DC-powered Low-Power Cyber Hardened IBUC Functional Circuit Block Diagram

RS232
J2
Alarm
Switch Control
FAN
J4
TCP/IP DC/DC
DC/DC
C/ DC All
Power Supply
Supp
ply Circuits
J3
VDC
Internal
10MHz
VDC
M&C
M&
&C
External
10MHz
1
10MH z
Detector
Dete
tect
tector
cto Multiplier
Multip
plier
PL
PL DRO
DRO
R
De-Mux
VDC
M&C
M&C M&C
M&
&
J1
External 10MHz
L-Band
RF OUT
Gain Temp
or
Adjustt
Adjust
Adj Comp
M&C M&C M&C
Figure 2.7 DC-powered Cyber Hardened IBUC Functional Circuit Block Diagram

RS232
J2
Alarm
Switch Control
FAN
J4
TCP/IP AC DC
AC/DC
AC/D All
Power
Powe
Power Supply Circuits
J3
VAC
Internal
10MHz
M&C
M&C
M&
&C
External
10MHz Detector
Dete
tect
tector
cto Multiplier
PL D
DRO
RO
De-Mux
External 10MHz M&C

M&C M&C
M&C
J1
L-Band
RF OUT
Gain Temp
p
or
Adjust
Adjust
Adjust Comp
M&C M&C M&C
Figure 2.8 AC-powered Cyber Hardened IBUC Functional Circuit Block Diagram

Software
The Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G monitors and
controls numerous parameters and has features which simplify installation and use and
enhance system performance.
Some of these key features include:
• Monitor and Control

The IBUC can be monitored and controlled through a couple of interfaces
including RS232 and Ethernet port. See Chapter 5, Monitor and Control Features,
for a full description of these functions.
• Tx Attenuation
The gain of the unit can be set over a 30 dB range in 0.1 dB steps.
• Automatic Gain Control (AGC)
The IBUC continuously monitors input and output levels. When AGC is enabled,
the gain of the system is maintained at a constant level by an internal algorithm.
Gain is the difference between output power and input power.
• Automatic Level Control (ALC)
Similar to the AGC system, when ALC is enabled, the gain is adjusted to maintain
a constant output level.
• Input Power Overdrive Protection
Based on internal selectable stable references, transistor overdrive will be
measured and automatically assessed. Terrasat’s Inc. algorithm allows the input
overdrive point to be up to 6dB higher than the selected reference point. If such
condition is not met, internal attenuators will be activated to limit power delivery.
• Embedded Web Pages (HTTPS)
• Simple Network Management Protocol (SNMPv3)
Provides integration of IP M&C in existing network management systems.
• Burst Operation
Enables operation in burst mode. The IBUC reports peak output power of valid
bursts (above a burst threshold) when in burst mode.
• Event History (with time stamps)
A log of events that occur is maintained. This can simplify troubleshooting of the
system (especially when an intermittent problem occurs).
• Sensors
A series of internal sensors enable you to verify performance and to troubleshoot
the system. Sensors include internal temperature, 10 MHz input detector, supply
voltage, current consumption, phase-locked dielectric resonator oscillator

(PLDRO) lock voltage, input level and output level.
• Statistic History
A log of system core statistics is automatically gathered and maintained. This
resource can simplify troubleshooting of the system. For a complete list of which
variables are gathered, refer to command SHL on page C-31.
System Configurations
Figure 2.9 to Figure 2.11 show typical earth station installations using Terrasat block
upconverters. In normal operation, the IBUC and the low-noise block downconverter
(LNB) are mounted outdoors. Depending on the model of the IBUC, the PSUI can be
mounted indoors or outdoors. The IBUC and the LNB can interface directly with a
satellite modem, a 70 MHz to L-band rack converter or modem combiner network.
Table 2.10 lists the requirements for proper operation.
Table 2.10 Basic System Requirements
IBUC LNB
DC supply DC supply
~ from the modem ~ from the modem
~ from the outdoor PSUI 10 MHz reference signal
~ from the indoor PSUI ~ internally referenced
~ from the telecom station ~ externally referenced
AC supply ~ free running
~ AC mains RF input
10 MHz reference signal ~ from the antenna
~ internally referenced
~ externally referenced
L-band signal
Certain considerations must be made when selecting the IFL because appropriate
shielding and signal levels are required for normal system operation. The IBUC is
designed to operate with a -30 dBm Tx L-band input signal to achieve rated power at
maximum gain/minimum attenuation. The Cyber Hardened IBUC 2, IBUC 2e,
IBUC 2G, IBUC R or IBUC G provides a variable attenuator that is accessible
through the various M&C interfaces that enables the gain of the unit to be reduced by
up to 30 dB in 0.1 dB steps. The attenuator can be used to prevent overdrive to the
IBUC in configurations with a short cable run (or IFL), thus preserving the dynamic
range of the modem. In addition, the externally referenced IBUC and the externally
referenced LNB must have a 10 MHz input signal at +5 dBm to -12 dBm for the
IBUC, and 0 dB to -10 dBm for the LNB. The maximum voltage drop for a 24 VDC
IBUC is 4 volts and the maximum drop for a 48 VDC IBUC is 11 volts.
For AC-powered IBUCs, the range is 100 VAC to 240 VAC. For higher power units
operate from 200 VAC to 240VAC.
Note: The system configurations in Figure 2.9 to Figure 2.11 depict an external 10 MHz
reference signal; however, an optional internal 10 MHz reference signal is available.
Note: Not all the DC units have a power supply via coax cable (Port J1). For further
information, please consult the most updated product lists on our data sheets on our
website: https://www.terrasatinc.com/products/

Figure 2.9 DC Low Power IBUC System Configuration
Figure 2.10 DC Power IBUC System Configuration

Figure 2.11 AC Power IBUC System Configuration
Storage Information
All Terrasat’s equipment and systems are projected to perform indoor and outdoor in
various environment types around the globe. Even so, our systems are projected to
perform plugged in. When connected to the Satellite Communication Systems, the
units can be exposed to the natural environment. However, there are some limitations
for storing them unplugged that should be considered. For instance, we recommend
users use a water-resistant container to store it disconnected from other systems.
There are no particular limitations for storing the Cyber Hardened IBUC 2, IBUC 2e,
IBUC 2G, IBUC R, or IBUC G other than avoiding excessive exposure to:
• Extreme temperatures beyond the range between -45 °C to +65 °C (-49 °F to

+ 149 °F) external ambient temperature. Other than that, there is no need for any
particular temperature monitoring or control.
• Extreme exposure to water or other liquids: The IBUCs should never be
submerged in any kind of liquid. Even though these types of equipment have
water-resistant capabilities, they will not necessarily resist full dipping on liquid
environments.
• Extreme exposure to impact: The units must have their physical integrity
preserved.
• Extreme exposure to dust, dirt, sand or similar substances: Excessive exposure to
such tiny particles may cause problems such as affecting the fans' function and
contribute to overheating.
• Fire: The units must never be exposed to fire.
While storing your IBUC units, make sure to keep them in a weather-protected
environment.
Note: Once the IBUC unit is protected from extreme environmental conditions, it can be
stored with no necessity for any extra monitor and control system.
Note: If you store it for transportation, it is recommended to use a water-resistant recipient

and transport the equipment disconnected from other systems.
Note: The units' connectors are only sealed against weather exposure when connected to
their respective cables.
Note: If the units are exposed to higher or lower temperatures than those mentioned above,
"Extreme temperatures," users must provide adequate acclimatization.

3
C HAPTER
INSTALLATION
CHAPTER3
This chapter contains the general requirements for installing the Terrasat outdoor unit
(ODU).
Introduction
The ODU consists of an intelligent block upconverter (IBUC) and a low-noise block
converter (LNB). An power supply (PSUI) can also be part of the configuration.
General Requirements
! WARNING
For protection of personnel and equipment, use care when installing the
antenna and whenever working on or around the system.
Follow standard safety precautions with hand or power tools.
Use care when working with high AC voltages and microwave emissions.
Unpacking
Check to make sure that the ODU has not been damaged in shipment. If there is any
damage, contact the shipper before proceeding. If you need to declare any equipment
as damaged during transit, save the original shipping cartons to ease inspection
reporting.
Terrasat recommends retaining and re-using all shipping cartons and foam forms if the
equipment will be stored or reshipped. The cartons should be clearly marked to
indicate that they contain fragile electronic equipment.
Compare the contents of the shipping container with the packing list to ensure that all
items have been received. If any item is missing, contact Terrasat.
Furnished Items
The following list describes items that are furnished with Terrasat Communications,
Inc. Cyber Hardened IBUC’s. Refer to Figure 3.1 for visual representation of such
items.
Figure 3.1 Furnished items with Cyber Hardened IBUC 2
A. An Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G with an
integrated solid state power amplifier (SSPA)
1. Product documentation on CD
2. Waveguide gaskets and hardware (waveguide units only)
3. Test datasheet
4. DC supply mating connector (for units with DC supply)
Figure D.5 on page D-5 contains information about fabricating your own DC
supply cable.
5. AC supply mating connector (for units with AC supply)
Figure D.5 on page D-5 contains information about fabricating your own AC
supply cable.
3-2 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Installation
6. Sealing tape for Type-N connector

7. 5 g pouch of Permatex anti-seize lubricant
The anti-seize lubricant is a heavy duty high-temperature lubricant that prevents
galling (friction between metal parts that can weld the nut and bolt together and
prevent removal), seizing, and corrosion of fasteners during assembly and aids the
disassembly of parts exposed to heat or corrosive environments.
8. Fuses | The fuses are intended for 220 VAC operation and are only supplied with
units that operate over the range of 100 VAC to 240 VAC.
9. [Optional] 19-pin M&C (Monitor and Control) mating connector.
10. [Optional] IP67 industrial RJ45 mating connector.
11. [Optional] Mounting brackets and bolts. See Figure 3.6 on page 3-12.
Accessories
The following are optional accessories:
• A waveguide Rx reject filter

• A four-way combiner/divider module
• A TCP/IP test cable
• Waveguide pieces
• IFL cables (for example, LMR-400)
• Installation kits
Note: Exact contents of the shipping carton vary according to the model and type of IBUC.
Installing the ODU

Consider the following when preparing to install the ODU.
Tools
Have available a standard electrician’s toolkit and any tools listed in the antenna
manufacturer’s installation instructions.
Test Equipment
Terrasat recommends the equipment or its equivalent listed in Table 3.1 for
installation and system alignment.
Table 3.1 Recommended Test Equipment

Equipment Type
Spectrum Analyzer Agilent HP8563E
General Requirements | 3-3

Table 3.1 Recommended Test Equipment (Continued)

Equipment Type
Digital Voltmeter Fluke 8050
Waveguide-to-coaxial Adapter C-band or Ku-band
RF cables With calibrated insertion loss up to 15 GHz
40 dB attenuator High power to match HPA output
Assortment of cables, connectors and adapters
(calibrated up to 15 GHz)
Site Considerations
The ODU is designed to be mounted on or near the antenna. Locate and install the
antenna according to instructions supplied by the antenna manufacturer. Choose an
area that is free of interference from motors or other electrical equipment and that has
a clear line of sight from the antenna to the satellite. Use size 3/0 or 4/0 AWG
(American Wire Gauge) stranded copper wire to ground the Cyber Hardened IBUC 2,
IBUC 2e, IBUC 2G, IBUC R or IBUC G to the antenna frame and to the lightning
protection ground rod. For higher power units with an external power supply, Terrasat
recommends using an isolation filter to reduce power line interference.
Mounting Considerations
Optional mounting brackets are available to aid mounting on most antennas. The ODU
must be mounted such that:
• The IBUC has sufficient support to minimize the effects of antenna sway in strong
winds.
• The fan intake and exhausts are free from any obstructions.
• The heat fins have air movement across them.
Ensure:
• That cables and waveguides are not crimped or pinched during the processes
required for installation, polarization, azimuth, or elevation adjustments.
• There is adequate slack for the cables.
Power Requirements
! WARNING
Installation and connection to the line power supply must comply with
applicable wiring codes and regulations.
For DC-powered IBUC models with a rated power level of 25 watts or below for
C-band, 20 watts and below for X-band, 16 watts and below for Ku-band and 10 watts
and below for Ka-band, the power for the IBUC can come either from the IFL supplied
from the Terrasat indoor unit (IDU) equipped with a 200 watts power supply or from a
satellite modem equipped with a suitable power supply. DC power for these lower
power IBUCs can also be supplied directly through the external power connector (J3)
by using the Terrasat 250 watts external power supply. Refer to the part number label
(shown in Figure A.1 on page A-1) to determine voltage requirements. Ensure that
24 VDC input voltage is from 20 VDC to 28 VDC and that the 48 VDC input is from
37 VDC to 60 VDC.
Note: Power for the IBUC 2e comes only via coaxial cable. Refer to the datasheet in
Appendix D, Component Specifications and Reference Drawings for power
requirements.
Outdoor Power Supply

Terrasat offers four models of outdoor power supplies. DC-powered IBUCs with a
rated power level higher than 25 watts C-band, 25 watts X-band or 16 watts Ku-band
require a separate power supply. Units that get their power from the earth (or telecom)
station do not require an external power supply. Table 3.2 lists the four outdoor power
supply models and applications for each. Power supplies have an autoranging AC
front end that works with both 115 VAC and 230 VAC.
Note: The IBUC is configured at the factory to be floating. Ensure that the correct polarity is
applied to any unit.

Table 3.2 Terrasat Outdoor Power Supplies
Model Output Power Application

• C-band up to 25 W
• X-band up to 25 W
PSUI-948-0250S-4 250 W
• Ku-band up to 16 W
• Ka-band up to 16 W
• C-band up to 80 W
• X-band up to 80 W
PSUI-948-600-4 600 W
• Ku-band up to 50 W
• Ka-band up to 40 W
• C-band 100 W to 125 W

PSUI-948-1000-4 1000 W • X-band 100 W to 125 W
• Ku-band 60 W to 80 W
• C-band 150 W to 200 W

PSUI-948-600-4 1200 W
• X-band 150 W to 175 W
All IBUCs that are AC-powered and all Terrasat outdoor PSUI’s are furnished with a
detachable AC power connector that is used to connect and disconnect power. When
connecting the AC connector to the AC power source, the wiring must include a 15 A
or 20 A circuit breaker. A disconnect device (such as a circuit breaker or mains supply
plug on the power supply cord) that is readily accessible must also be provided. Any
outdoor AC connections should be made using suitable connectors or boxes with an
IEC protection class of at least IP65.
! WARNING
Ensure AC power is off when connecting or disconnecting the power
supply unit's power cord. To turn off AC power to the unit, use the
installed circuit breaker or a similar disconnecting device.
If a circuit breaker is not easily accessible as a disconnecting device, the input

connector will be the disconnecting device. In this case, the socket-outlet must be
installed near the equipment and must be easily accessible for pluggable equipment.
All AC-powered IBUCs and the Terrasat outdoor PSUI are furnished with mating
connectors for the AC mains power cable. To remain compliant with European Low
Voltage Directive (EN 60950-1), use a power cable that meets IEC 60227
requirements such as HAR Cable Designation H03VV-F or H03VVH2-F and/or
others with water resistance for outdoor applications. Power cable plugs must also
comply with all applicable local and federal standards and regulations.
Indoor Power Supply

Terrasat offers a 1000 watts indoor power supply unit (PSUI) which provides 48 VDC
power. The 1000 watts PSUI can power C-band and X-band units through 125 watts,
Ku-band units through 80 watts, and Ka-band units through 40 watts. Each indoor
PSUI is packaged in a rack-mountable chassis which occupies one rack unit (1.75 in.)
of space. The indoor PSUI is shipped with a mating connector for DC power and a
power cord for AC mains.
Note: AC transients and surges can cause data transmission errors and loss of
synchronization in the modem and/or the ODU. Take proper precautions to ensure
uninterrupted service.
Grounding
Terrasat recommends the following grounding and lightning protection:
• Cable Shielding
Shield currents can be eliminated with proper techniques. A grounding strap at the
end of the coaxial and data cables should be connected to the ground lug at the
antenna base with #4 gauge copper wire. This provides a path of least resistance
prior to entering the equipment.
• AC
The best way to protect the equipment is to have two protectors. The first is the
power mains protector that is mounted directly across the mains in the breaker box.
The second should be mounted or grounded directly at the base or hub of the
antenna or at the 19-in. rack.
• Data and Control Lines
The I/O lines can deliver surge current to the equipment and should also be
protected.
• Electrical Grounding
Grounding of the IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G and PSUI
units is recommended to prevent possible damage from lightning or other induced
electrical surges. Terrasat recommends using 3/0 or 4/0 AWG stranded copper
wire for bonding the IBUC and the PSUI to the earth ground (or grounding rod),
using the most direct or shortest route.
Antenna Recommendations
Most antenna masts are encased in concrete. Typically, the mast pipe is submerged in
a 4 ft to 5 ft (1.22m to 1.53m) deep augered hole. This provides a good Ufer ground.
A Ufer ground encases grounding connectors in concrete. Concrete absorbs moisture

quickly and loses that moisture slowly—as much 15 to 30 days after rain or snow
melt). The mineral properties of concrete and their natural pH mean that concrete has a
supply of ions to conduct current. The soil around concrete becomes “doped” by the
concrete and, as a result, the pH of the soil rises. The moisture in the concrete in
combination with the “doped” soil make a good connector of electrical energy. The
concrete’s large volume and area of contact with the surrounding soil allow a good
transfer to the ground. In the concrete base, a Ufer ground can be established by
running #4 gauge solid wire or rebar and connecting to the base of the pedestal with
pigtails.
The Ufer ground is only one step in proper grounding. The Ufer ground should be
augmented with coupled pairs of 10 ft (3.05m) ground rods placed 20 ft (6.1m) into
the ground, spaced 20 ft (6.1m) apart. The first rod should be placed close to the
antenna. The second rod should be placed towards the equipment enclosure. A #2
gauge wire should connect the rods and antenna mount. A ground rod should be placed
at the equipment enclosure, as well. If it is virtually impossible to install the ground
rods, then radials are needed. This can be accomplished by laying 10 or more lengths
of 1½-in. (3.81cm) copper strap at least 50 ft (15.24m) long in a radial fashion around
the antenna base. The straps should be buried, if possible. The hub must be
interconnected to the utility ground.
The ground configuration can vary from one location to another. It is best to measure
soil conductivity and design a 5 Ω or less ground system. To protect the system from a
direct strike, a lightning rod placed 2 ft (61cm) higher than the highest point of the
dish should be interconnected to the Ufer ground with #2 gauge copper wire.
Antenna Mounting
The IBUC has a variety of mounting options: on the focal point, the boom arm, the
antenna back structure, or in the hub (depending on the antenna type).
Note: Figure 3.2 and Figure 3.3 are photographs of actual installations.
Figure 3.2 IBUC 2 Field Installation

Figure 3.3 IBUC 2 Installation
The Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G have
mounting holes on both sides of the unit that can be used to attach the IBUC to the
antenna. For the location of these mounting holes, see Figure 3.4.
Figure 3.4 Location of Mounting Holes
There is also a single mounting hole located on the front of the IBUC that is identified
in Figure 2.1 to Figure 2.3 on page 2-11. This mounting hole is on the same axis as the
center of the waveguide of the unit (that is, it is in line with the center of the
waveguide). This single mounting hole enables the unit to be rotated when mounted on
the focal point of an antenna.
Figure 3.5 IBUC In Line Mounting Configuration

Optional mounting brackets are available that aid in attachment to antennas. The
mounting slots identified in Figure 3.6 on page 3-12 give you additional flexibility
when attaching the IBUC to the antenna.
Note: Ensure that the threads of the bolts used for mounting the IBUC have been dipped in
the included Permatex anti-seize lubricant. This prevents galling, seizing, and
corrosion of fasteners during assembly and will aid in future disassembly. For more
information about applying the Permatex lubricant, see page 3-18.
Figure 3.6 Location of Adjustment Slots on Optional Mounting Bracket
System Pressurization
The IBUC chassis contains a breather valve (the location is identified in Figure 2.1 to
Figure 2.3 on page 2-11) that is designed to equalize pressure inside and outside of the
unit while allowing the passage of air or water vapor but not environmental
contaminants such as liquids, debris, or dust. If you intend to pressurize the
waveguide, you must install a pressure window at the output of the IBUC; otherwise
the breather valve will not permit pressurization of the system.
Note: IBUC units designed for Ka-band operation have pressure window already installed at
the output of the IBUC and are able to operate with pressurized waveguide
configurations.
System Cabling Requirements
Cables and Connectors

Interface connectors for the Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R
or IBUC G and their mates are listed in Table 3.3. Additional mating connectors and/
or cables can be ordered from Terrasat at optional items.
Table 3.3 Interface Connector Schedule
Reference
Function Interface Connector Interface Connector Mate
Designator
TYPE-N SOCKET TYPE-N PLUG
J1 Tx Input
(TYPE-F SOCKET optional) (TYPE-F PLUG optional)
AMPHENOL CIRCULAR, BOX AMPHENOL CIRCULAR,

M&C
J2 MOUNTING SOCKET, 19S STRAIGHT PLUG, 19P
Interface
(PT02E-14-19S (027)) (PT06E-14-19P (475))
AMPHENOL CIRCULAR, BOX AMPHENOL CIRCULAR

J3 DC Power MOUNTING SOCKET STRAIGHT PLUG
(ACS02E14S-6P (553)) (ACS06E14S-6S(553))
CONNECTOR, MALE CONNECTOR, FEMALE

RECEPTACLE, 3P PLUG, 3P
J31 AC Power
(AMPHENOL (AMPHENOL
C016 20C003 100 12) C016 20D003 110 12)
CONNECTOR, MALE CONNECTOR, FEMALE

RECEPTACLE, 4P PLUG, 4P
J32 AC Power
(HIROSE (HIROSE
H/MS3102A22-22P-D-T(73)) H/MS3106A22-22S-D-T(73))
RJ45-IP67 SHIELDED INLINE

J43 Ethernet RJ45-IP67 PLUG
CONNECTOR WITH CAP
CPR137, CPRG WAVEGUIDE OR CPR137, CPRF WAVEGUIDE

RF Output C-band
TYPE-N SOCKET OR TYPE-N PLUG
RF Output X-band CPR112, CPRG WAVEGUIDE CPR112, CPRF WAVEGUIDE
WR75 COVER FLANGE WITH

RF Output Ku-band WR75 COVER FLANGE
GROOVE
WR28 COVER FLANGE WITH

RF Output Ka-band WR28 COVER FLANGE
GROOVE
1. Three-pin J3 connector is only used in AC powered units.

2. Connector used for High Power units
3. Ethernet port does not support PoE

J1 – Transmit In The Tx Input connector is a Type-N socket (Type-F socket,

optional) connector used to connect the IF at L-band from the modem to the IBUC.
Use 50 Ω cables (75 Ω for Type-F connectors) to connect to J1. Certain considerations
must be taken when selecting the IFL because appropriate shielding and signal levels
are required for normal system operation. The IBUC is designed to operate at rated
power with a –30 dBm Tx L-band signal, with the variable attenuator set to minimum
attenuation. The variable attenuator is accessible through the M&C interfaces for
system gain adjustment. In addition, the IBUC must have a 10 MHz input signal from
+5 dBm to –12 dBm (only for those IBUC models with an external 10 MHz reference
signal). For IBUC models with both the optional internal reference signal and an
external 10 MHz signal, the external signal will automatically receive priority without
any user interaction.
For lower wattage IBUCs that are DC powered, the coaxial cable should be selected
for its current carrying capacity. A lower wattage IBUC can draw up to 6.0 amps. The
maximum voltage drop for a 24 VDC IBUC is 4 volts and the maximum voltage drop
for a 48 VDC IBUC is 11 volts. The cable should also have good shielding
effectiveness in order to prevent outside interference.
Note: The caution symbol, shown in Figure 3.7, is printed on the chassis next to the J1
connector indicates that VDC may be present. In general, lower power IBUCs allow
DC power via coaxial cable. However, AC-powered IBUCs cannot be supplied via
coaxial cable.
Figure 3.7 Connector J1 Caution Symbol
Note: Fire codes may require that cables in occupied building be installed in steel conduit.
Local government agencies may waive this requirement with the use of Plenum cables
which are standard cables encased in solid Teflon. Check codes for your area.
Note: Equipment outages due to faulty installation are not covered by the Terrasat warranty.
Terrasat recommends following OEM procedures when making cables and
connectors.
J2 – M&C Interface The M&C interface is a 19-pin circular socket connector used to
enable remote monitoring and control of IBUC operating parameters. Pin assignments
are shown in Table 3.4. If the M&C port of the IBUC is going to be used, the cable
should be a shielded multi-conductor cable. For more information about fabricating
your own cable, see the IP cable drawing in Appendix D. An optional pre-assembled
IP test cable is available from Terrasat.
Table 3.4 Pin Assignments for M&C Interface Connector J2

Pin Function
A RESERVED
B RESERVED
C +5V
D RS232 RXD
E RS232 TxD
F GROUND
G RESERVED
H RESERVED
J Factory Reset
K RESERVED
L IBUC Alarm Output Normally Open
M IBUC Alarm Output Common
N Mute
P IBUC Alarm Output Normally Closed
R RESERVED
S RESERVED
T RESERVED
U RESERVED
V RESERVED
Note: Pin F is the return to close the circuit for RS232.

J3 – DC Power DC Power can be supplied to the IBUC through a 6-pin circular

socket connector. Pin assignments are listed in Table 3.5
Table 3.5 Pin Assignments for DC Power Connector J3

Pin Function
A VDC –
B VDC –
C VDC –
D VDC +
E VDC +
F VDC +
Note: The IBUC is factory configured for floating supply. J3 is internally connected and has
no VDC connection to Common.
Note: The operating voltage is integrated into the model number of each IBUC. For more
information about the model number of your particular model IBUC, see Appendix A.
! CAUTION
For some coutries 220Vrms is provided via Line-Line bus. If this is your
setup, connect one of the Line leads to the Line Pin of the IBUC connector,
and the other Line lead to the Neutral Pin of the connector.
In the case that 110Vrms is needed, or 220Vrms is provided via Line-Neutral
bus connect power leads to their matching connector pins.
J3 – AC Power AC Power is supplied to the through a 3-pin plus ground connector.

The connector is configured as described in Table 3.6.
Table 3.6 Pin Assignments for AC Power Connector J3

Pin Function
1 N/C
2 Neutral
3 Line
4 Ground
Note: For high-power IBUC models such as IBUC G shown in Figure 2.4 on page 2-12,
military grade Hirose connector is used.
J3 – AC Power AC Power for high power units is supplied via specialized 4 pin
Milspec connector. The connector is configure as described in
Table 3.7 Pin Assignments for Milspec High-Power AC Connector J3
Pin Function
A Ground
B Neutral
C Line
D Ground
J4 – Industrial Ethernet Connector The industrial Ethernet connector is an

IP67-rated RJ45 Cat. 5e interface with a locking protective cover. The connector is
configured as described in Table 3.8.
Table 3.8 Pin Assignments for Ethernet Connector J4

Pin Function
1 TCP/IP Tx(+)
2 TCP/IP Tx(–)
3 TCP/IP Rx(+)
4 Not Used
5 Not Used
6 TCP/IP Rx(–)
7 Not Used
8 Not Used
! WARNING
The IBUC Ethernet circuit does not support Power Over Ethernet (PoE)
functionality. Routing PoE connection to port J4 might irreversibly
damage IBUC unit.
RF Output The types of waveguide used for various bands of the IBUC are listed in
Table 3.3 on page 3-13.

Cable and Waveguide Connections
! WARNING
Ensure that all power is disconnected prior to making any connections.
When installing the cable and waveguide assemblies, ensure that all connections are
weather tight. If an Rx reject filter is being used, attach it to the IBUC waveguide
output. Use proper gasketing methods to prevent the entry of water.
Water-Resistant Wrap
Terrasat recommends applying water-resistant wrap (such as mastic tape) to all
outdoor connectors to prevent the entry of water and subsequent water damage. Mastic
tapes are designed to flow and self-heal if cut or punctured. When applied spirally with
the proper tension, mastic tapes form a tight continuous coating that permits little or no
moisture absorption or penetration. Terrasat provides water-resistant sealing tape for
Type-F and Type-N connectors.
Apply the mastic tape, as follows:
1. Ensure that all connectors are firmly tightened, dry, and free from all grease, dust,
and dirt.
2. Cut the mastic tape to the desired size. The tape should be long enough to cover the
connector completely.
3. Center the tape on the connector to be sealed and wrap the tape in a tight spiral
around the connector using a 50% overlap. Squeeze the tape tightly and ensure that
both ends of the tape have formed around the connector and the cable with any
gaps.
Apply the tape to all connectors that may be exposed to moisture.
Applying the Anti-Seize Lubricant

Terrasat recommends applying anti-seize lubricant to screws and bolts that could be
exposed to weathering or corrosive environments. The lubricant prevents galling,
seizing, and corrosion during assembly and aids in future disassembly. A 5 g pouch of
Permatex anti-seize lubricant is included with the installation kit for this purpose.
To apply the anti-seize lubricant,
1. Wear appropriate person protection equipment to avoid contact with skin and eyes.
This includes safety glasses, neoprene or nitrile gloves, and clothing sufficient to
limit skin exposure.
2. Ensure that mating surfaces (screw holes) are clean, dry and free of dirt, debris, or
loose surface rust.
3. Use a brush or lint-free cloth to apply a think coat of anti-seize to the screws and
bolts that require protection, as shown in Figure 3.8. The anti-seize should be
applied right down to the base of the threads.
Figure 3.8 Applying the Anti-Seize Lubricant
4. Spread the lubricant to a thin film without any lumps.

5. Reassemble the parts using normal torque values.
6. Wipe off any excess material with a disposable towel.
Waveguide Connections
If necessary, connect a section of flexible waveguide between the orthogonal mode
transducer (OMT) transmit port and the IBUC Tx RF output (or optional Rx reject
filter). The waveguide should be attached to the antenna feed according to the
manufacturer’s instructions. Use proper gasketing methods to prevent water entry and
subsequent damage.
Note: During installation, be sure to remove the sticker shown in Figure 3.9 that covers the
waveguide flange. The sticker itself does not create a pressure window and will allow
moisture to enter the waveguide. Also be sure to install the waveguide gasket into the
channel identified in Figure 3.9 to ensure a good seal between surfaces. Do not re-use
old gaskets.

Figure 3.9 Waveguide Label and Channel for Gasket
! WARNING
The output of the IBUC is microwave power. Never look into the
waveguide or put your head into the path of the beam that goes to the
satellite.
Basic System Alignment

The following sections outline the procedure for setup and alignment of an earth
station. Before you align the ODU, the antenna should be set to the desired azimuth
and elevation settings per the manufacturer’s instructions.
Ensure that the IBUC Tx output power is disabled to prevent accidental transmission
interference with adjacent satellite or transponders before attempting to align or
perform any other operation involving the ODU. Before attempting any signal
changes, carefully evaluate the possible effects of the transmitted signal.
! CAUTION
The IBUC must not transmit until alignment and any necessary
adjustments are complete.
Setting the Tx and Rx Frequencies

All transmit and receive frequencies are set in the modem.
If using a direct connection to an L-band modem, follow the manufacturer’s

instructions for setting the transmit and receive frequencies.
Receive L-band Output Measurements

To check the receiver,
1. Ensure that 15 VDC to 24 VDC (LNB Bias) is present at the modem input.
2. Use a spectrum analyzer to ensure that the 10 MHz reference signal is present at
the modem.
! WARNING
DC power will be present on the cable. Terrasat recommends the use of a
DC block when using a spectrum analyzer.
3. Connect the LNB to the demodulator’s Rx input by attaching the coaxial cables
from the Rx L-band output on the LNB to the demodulator’s Rx L-band input port.
Transmit Power Alignment
Transmit L-band Input Adjustment with Modem or Converter
! WARNING
DC power might be present on the cable. Terrasat recommends the use
of a DC block when using a spectrum analyzer.
To set the power level of the modulator output,
1. Use a spectrum analyzer to measure the power level of the L-band signal at the
output of the coaxial cable that connects to the IBUC at the Tx L-band connector
J1.

2. Use the level adjust mechanism of the modem or converter to increase or decrease
the power level. Adjust to reach a level of –30 dBm. (All IBUC units are designed
to reach rated power at P1dB over frequency and temperature with -30 dBm at the
input when the attenuator is set to minimum attenuation.) For some modems and
shorter cable runs, it is not possible to reach –30 dBm. In this case, the attenuator
in the IBUC may be used instead.
3. Check that the 10 MHz reference signal is present and within the range of +5 dBm
though –12 dBm.
Note: The Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC G require
a 10 MHz reference signal to operate. Check the model number of your IBUC to
determine whether an external 10 MHz signal is required.
4. Disconnect the spectrum analyzer from the coaxial cable.
Transmit RF Output Adjustment with Modem or Converter (70 MHz to L-band)

To adjust the power level of the IBUC transmitter output,
1. Connect a waveguide-to-coaxial adapter and a 40 dB high-power attenuator to the

IBUC waveguide output.
2. Ensure that DC power to the IBUC is applied in the proper voltage range.
(Depending on your setup, this could be through the coaxial cable or through the
J3 connector.)
3. Connect the Tx L-band input signal to the Tx L-band connector J1 on the IBUC.
4. Enable the Tx signals in the modem or converter and the IBUC.
5. Measure the RF output with a power meter connected to the attenuator attached at
the waveguide output. For accuracy, measure pure carrier (that is, continuous wave
or CW) and the frequency allotted to you by the satellite network operations center
(NOC).
6. If the modem still has available range, use the level adjust mechanism to reach the
designated power level. If there is no available range, use the attenuation setting on
the IBUC instead.
Note: To set attenuation on IBUC, you first need to establish communication with the
IBUC. For more information about the various M&C interfaces you can use to
establish communication, see Chapter 5, Monitor and Control Features.
7. If using a satellite modem, adjust the RF output to the designated power level
(provided by the satellite network operations center or its engineering staff) with
the L-band output (modem) level adjust mechanism.
8. Disable the Tx signal in the modem or converter.
9. Disconnect the Tx L-band input signal.
10. Remove the waveguide-to-coaxial adapter and install the transmit waveguide
section to the antenna transmit feed.
11. Once the transmit input and output power levels have been set, begin transmitting
by connecting the Tx L-band input signal to the J1 connector on the IBUC and
enabling the Tx in the modem or converter.
12. Under the guidance of NOC staff, fine-adjust the transmit power for the desired
down link margin at the receiving station by adjusting the Tx L-band output level
adjust (modem or converter output) or by adjusting the gain of the IBUC by setting
the Tx attenuator.
Final Checks
To ensure reliable operation, inspect the system for crimped or pinched cabling. Make
sure that all connections are secure and sealed. Once the system has been aligned and
is operating satisfactorily, the IBUC will require infrequent maintenance.
Final Checks | 3-23

4
C HAPTER
OPERATIONS
CHAPTER4
This chapter describes general operation of the Cyber Hardened IBUC 2, IBUC 2e,
IBUC 2G, IBUC R and IBUC G.
Introduction
After the Cyber Hardened IBUC has been mounted and connections verified, the
antenna must be aimed towards the appropriate satellite. Follow the antenna
manufacturer’s instructions, using the coordinates (azimuth, elevation, and polarity)
provided by the satellite operator. Do not transmit until you have received
authorization—including a transmit power level—from the satellite network
operations center (NOC) staff.
Start-up Checklist
The IBUC leaves the factory preconfigured for operation; however, you can fine-tune
its settings for your particular needs.
Prior to start up, verify the following:
• Transmit/Receive frequencies
All transmit and receive frequencies are set using the modem. Follow the modem
manufacturer’s instruction.
• Cable connections
Ensure that all of the external cables between the IBUC and other equipment are
seated correctly and that there are no breaks or cracks, no sharp bends, pinch
points nor flattened sections in the cables.
• Power
Ensure that the IBUC is receiving power, Power can come via the modem, an
external power supply, or from AC mains.
If power is supplied by the modem, ensure that the modem provides the correct DC
voltage and the DC power has been enabled.
• 10 MHz reference signal
Verify that the 10 MHz reference signal is present. Some IBUC models have an
internal 10 MHz reference signal. If this option is not available, a 10 MHz
reference signal supplied on the IF cable from the modem is required.
Turning On the IBUC

To turn on the Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G,
1. Connect the L-band input cable (J1), the M&C cable (J4), and the power cable (J3)
2. Apply power to the IBUC.
3. The Power LED on the side of the unit next to the J4 connector lights up.
A flashing green light indicates that the IBUC is operating normally.
A red light indicates only that a fault (or alarm) has occurred. (A flashing red light
indicates a minor alarm and a solid red light indicates a major alarm.)
4. Allow the unit to warm up for approximately 15 minutes before operating the
transmitter module. This will assure stable gain and power.
Setting Operating Parameters

To set operating parameters, the IBUC must be connected to a terminal (for example, a
terminal emulator such as Putty, or the Embedded Web Pages via a PC). Connect the
IBUC to the Ethernet port of a PC by using a TCP/IP cable assembly (such as the one
depicted in Figure D.3 on page D-3).
Most of the procedures below can be accomplished by using the steps provided in
Appendix B, Embedded Web Pages. For user creation and deletion only RS232 or
SSHv2 interfaces are available.
1. Establish a connection with the Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G,
IBUC R or IBUC G by using either RS232 or SSHv2, described in Chapter 5,
Monitor and Control Features or by the steps provided in Appendix B, Embedded
Web Pages.
2. Set the Tx Output current state via TST command. See page C-53 for further
description. Output can assume one of the following values,
• Tx Disabled
• Tx Enabled, Not Muted
• Tx Enabled, Muted
4-2 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Operations
When the Tx Output is set to Disabled, the Tx Output level displayed from com-
mand TPO reads -99.0 dBm. This is not the actual reading. See page C-51 for fur-
ther description.
When conditions cause the automatic shut-off of the Tx Output signal, the Tx
Output is muted and the Tx Output level displayed from command TPO reads
-96.0 dBm. This is not the actual reading.
3. Configure the Power Monitor Frequency to set at which frequency you are
operating. Use the TFR command described on page C-47. The factory default
values in Table C.6 on page C-48 are listed according to the model number of the
IBUC.
Note: To ensure accurate readings, you must set the actual operating frequency.
Example: If, according to your Satellite NOC, your allocated frequency is
6400 MHz, set the Power Monitor Frequency to 6400 MHz. Do not use the factory
default value unless that is your actual operating frequency.
Note: It is critical to the operation of the IBUC that TFR be set correctly. The configured
frequency increases the accuracy of input and output power readings. The
attenuator requires the TFR frequency to ensure accurate values are applied when
using the TPT command. See page C-51 for detailed operation of TPT command.
4. Set the Power Read Mode via TPM command. Options include:
• Burst
• Continuous Wave
See page C-50 for further description.

5. Set the Gain Mode via TGC on page C-48. Options include:
• Open
Open is the gain obtained when there is no feedback in the measuring loop.
• AGC (Automatic Gain Control)
The IBUC continuously monitors input and output levels. When AGC is
enabled, the gain of the system is maintained at a constant level by an internal
algorithm. Gain is the difference between output power and input power.
• ALC (Automatic Level Control)
Similar to the AGC system, when ALC is enabled the gain is adjusted when
changes are detected in order to maintain a constant output level.
Note: The IBUC has an internal temperature compensation feature that minimizes gain
variations due to to changes in temperature. This feature is configured at the factory
and requires no user input. For specific information about your particular model
IBUC, see the datasheets in Appendix D, Component Specifications and Reference
Drawings.
Start-up Checklist | 4-3

Setting the Tx Frequency (L-band)

Changing the L-band frequency will cause a change to the RF frequency. To set the L-
band frequency,
Web Pages.
2. Verify the data in the Band Inversion via TFI command. See TFI for further
information.
3. Calculate the IF frequency by using the following formulas:
IF = RF - LO Non-inverted/Low side
IF = LO - RF Inverted/High side
Note: RF and LO frequencies for various bands are provided from Table 2.1 on page 2-3
through Table 2.5 on page 2-7.
Setting Alarm Thresholds

Although the IBUC will function using the factory-configured settings, by setting high
and low level thresholds for the Tx Input/Output you can access more information
about events such as power fluctuations that might trigger an alarm. Alarms will be
generated when the input and output amplitudes fall outside of the threshold ranges.
For this reason, Terrasat recommends that once the user has reached the proper input
and output settings for their budget, to narrow the threshold ranges for alarms. To
display or set alarm thresholds,
Web Pages.
2. Set the Tx Input High/Low thresholds via TBH and TBL commands. See page C-
43 and page C-44 for further description.
The IBUC leaves the factory with a default range of -15 dBm to -60 dBm.
Example: After observing the unit, you determine that the IBUC operates
consistently at -37 dBm. Although the threshold range is 45 dB, that range is too
wide for everyday use. Instead consider setting the input thresholds at ±3 dB; this
would make the high level threshold -34 dBm and the low level threshold -40 dBm.
3. Tx Output High/Low thresholds are set via TAH and TAL commands. See page C-
41 and page C-42 for further description.
When you set up your system and the Tx Output reaches its budgeted level, Terrasat
recommends that, instead of the (P1dB - 20 dB) to (P1dB + 1 dB) threshold range
that is the default, you narrow the range between the high and low thresholds to
±3 dB.
Example: After observing the unit, you determine that the output level operates
consistently at 32 dBm. Although the threshold range is 21 dB, that range is too
wide for everyday use. Instead consider setting the output thresholds at ±3 dB; this
would make the high level threshold 35 dBm and the low level threshold 29 dBm.
If the IBUC unit is configured for burst power monitoring, command TBT will set
the burst threshold value. See page C-44 for further information.
4. Verify your settings.
Configuring Alarm States

The IBUC offers flexibility with the levels of alarms produced when user-specified
thresholds are exceeded.
1. Consider which alarms to configure. Table 5.1 on page 5-3 contains the default

alarm configuration. Each alarm that is user configurable can be set as a major
event, a minor event, or be disabled.
Monitor and Control Features.
3. Display or configure alarms to be major events or minor events by using
commands CM2 and CM1 respectively. See page C-16 and page C-17 for further
description.
4. Display or set suppressed alarms via CMS and TAZ commands. Use CMS
command to display or configure suppression mask and command TAZ to enable
or disable suppression. See page C-18 and page C-43 for further description.
Configuring ALC/AGC
The Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC G offer two
methods of ensuring consistent signal levels: automatic level control (ALC) and
automatic gain control (AGC).
ALC
When enabled, the Automatic Level Control (ALC) circuitry in the IBUC monitors
output levels and adjusts the gain to maintain a consistent output for input signal
variations. If a signal level is consistently below the predetermined target level, the
ALC will cause the gain to be increased until the target level is reached. If a signal
level exceeds the target level, the ALC will decrease the gain.
Start-up Checklist | 4-5

To enable ALC,
Web Pages.
2. Set Gain Mode to “Open” via TGC command. See page C-48 for further
description.
3. Set Tx Input and Tx Output Thresholds in order to determine a baseline setting.
See Setting Alarm Thresholds on page 4-4.
4. Change IBUC Tx Output level and monitor it via TPO command, see page C-51,
until it reaches the desired level.
Note: IBUC Tx Output Level can be adjusted by two methods. The user must either
change the modem output level, or change the IBUC’s internal attenuation level. In
the latter case, use the TPT command, described on page C-51.
5. When the Tx Output Level reading is equal to the level that you want to maintain,
enable ALC via TGC command.
The IBUC will now continuously self-monitor, increasing or decreasing the gain in
order to maintain a constant signal at the level you defined.
Note: The Tx Output Level is “captured” when ALC is enabled.
AGC
When enabled via TGC command, the Automatic Gain Control (AGC) circuitry in the
IBUC maintains the gain constant and equal to the target gain that was established
when AGC was enabled.
Gain control settings can drift with time or temperature changes. You can reset the
Gain Control function (when reset, the Gain Control returns to mid-range or 0.0).
Terrasat units enable you to offset the target by using the attenuation control without
having to first disable the ALC or AGC.
Example: Set the output power level to 40 dBm and enable ALC. From this point
forward, the ALC algorithm will maintain the output level at 40 dBm.
If you want to change the output level to 41 dBm, reduce the attenuation by 1 dB. The
target level will be updated automatically.
Configuring the External Mute

Pin N of the M&C interface connector has dual functionality: it functions as an alarm
input or an external mute.
External Mute
When the IBUC operates as a single thread IBUC, Pin N of the M&C interface
connector functions as an external mute. If it is not connected (left open), then
transmission is not muted. When Pin N is connected to Pin F (chassis ground),
transmission is muted.
To re-enable transmission, remove the Pin N connection to Pin F. Transmission will

now resume.For more information about the M&C interface connector, see System
Cabling Requirements on page 3-13.
Common Errors
LED is Red
A red LED indicates only that a fault (or alarm) has occurred and does not necessarily
indicate that transmission has stopped. A flashing red light indicates a minor alarm and
a solid red light indicates a major alarm. You can communicate with the IBUC to
determine what is causing the fault, and then clear the fault condition.
Web Pages.
2. To determine current alarm status, the user should query the IBUC via CAS
command, described on page C-6.
When the fault is cleared, the LED should be flashing green.
No Power to the Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or
IBUC G
If the Power LED is off or not turning on at all, the IBUC is probably not receiving
power.
Restore power to the IBUC by
• If the IBUC is powered by the modem, verifying that the modem is working
properly.
• Checking that the modem is receiving power (that is, the modem power cord is
plugged in) and that DC power to the IBUC is enabled.
• Checking that all cable connections are solid.
• Checking that the power supply is functioning or that AC mains has the proper
voltage.
Common Errors | 4-7

• Checking the disconnect devices such as the circuit breaker.

• Checking the fuses.
• For DC-powered IBUCs, the fuses are in the power supply.
• For AC-powered IBUCs, the fuses are in the IBUC.
Fuses are 5x20 mm time-lag glass body cartridge type.
! WARNING
Before applying power to the unit, ensure that the waveguide output is
properly terminated. Failure todo so could lead to serious personal injury,
excessive RF radiation levels, and equipment damage.
Time Stamp Data is Incorrect

Note: This only applies if the customer is not using NTP.
The time stamp on the alarm log may be incorrect after the IBUC has lost power for an
extended period. In such cases you can set the system date and time by using the
provided CLI commands. To correct Time Stamp Data,
1. Open Terminal session using either RS232 or SSHv2, described in Chapter 5,

Monitor and Control Features and login or by the steps provided in Appendix B,
Embedded Web Pages.
2. Check whether the IBUC time zone is correctly configured via command TZO on
page C-55.
3. Configure IBUC Real Time Clock via command CTM on page C-23.
Satellite Network Operations Center Doesn’t Recognize Signal

The Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G appears to
be transmitting a signal, but the satellite network operations center (NOC) cannot
identify your carrier.
To determine whether your settings are correct,
1. Verify that your frequency is within the bandwidth slot that was allocated to you.
2. Determine whether the IBUC operates with the LO on the low side or the high side
of the frequency that was allocated to you.
3. Check the signal mix. Remember that low-side is non-inverting and high-side is
inverting.
4. Use the following formulas to calculate IF frequency

low side IF = RF - LO Non-inverting
high side IF = LO - RF Inverting
The LO for each IBUC band is found in Table 2.1 through Table 2.4.
5. Check the Tx output state via TST command on page C-53, and Tx output level
via TPO command on page C-51.
When Tx output power is disabled, the Tx output level will read -99.0 dBm. This is
not an actual power reading; rather it indicates the loss of power.
When conditions cause the automatic shut-off of the Tx output signal, the Tx output
level will read -96.0 dBm. This is not an actual power reading; rather it indicates the
automatic shut-off of power.
Transmit Power in Saturation

The IBUC, at minimum attenuation, makes rated power at -30 dBm input. Operating
the IBUC at higher levels will result in spectral distortion and high intermodulation
levels. Terrasat recommends operating with power back-off levels sufficient to meet
the spectral density mask.
To avoid signal saturation,
1. Reduce input power from the modem.

2. Open Terminal session using either RS232 or SSHv2 and issue the command TPT
on page C-51 to modify the internal attenuation.
Tx Input/Output Level Verification

To verify the Tx IF Input level,

Embedded Web Pages.
2. Query the IBUC unit via TDT command, on page C-45.
To verify the Tx RF Output level,

Embedded Web Pages.
2. Query the IBUC unit via TPO command, on page C-51.
Common Errors | 4-9

If your reading does not match your expected level, first verify that the Cyber
Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G is receiving the
proper input level.
3. If the input is at the correct level, use the command TPT on page C-51 to modify
the attenuation to set the output to the expected level.
4. If, after setting the output to your expected level, you are still having transmission
problems, check the flexible waveguide and antenna feed for obstructions. Also
check the alignment of the antenna.
5
C HAPTER
MONITOR AND CONTROL FEATURES

CHAPTER5
This chapter describes the various Monitor and Control (M&C) features and functions
that the Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC G can
offer.
Introduction
To access any of the M&C interfaces, you must first establish a communication link
with the IBUC. Once that connection is established, we can configure and operate the
Monitor and Control Features.
M&C Interfaces
The Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC G offer the
following M&C (Monitor and Control) interfaces:
• RS232
• Multifunction LED
• Ethernet
RS232
The Cyber Hardened IBUC does not require any additional configuration for proper
RS232 operation. The RS232 port uses ASCII protocol at a fixed 115200 Baud Rate, 8
stop bits, with no parity, no flow control, and one stop bit for communication.
To initiate an RS232 session;
1. Connect the IBUC to the computer using the RS232 cable. To do so, you must
have a M&C 19-pin Plug (mating connector) connected to a DB9F cable.
The M&C 19-pin Plug must be connected to the IBUC while the DB9F Plug must
be connected to your computer.

You may find further details concerning this cable on Figure D.2 on page D-2. It
contains technical drawings and information that shows how to manufacture that
cable on-site if needed.
2. Activate a terminal emulation program such as PuTTY.
3. Configure Serial RS232 Session with matching baud rate, stop bits, parity, flow
control and stop bit, as given above and connect to the IBUC unit.
4. At the “IBUC Login” prompt enter the username. A default banner will be
displayed followed by the “Password” prompt.
5. Enter the previously defined password. After this step, the user should see the
“IBUC>” prompt.
At this point, one may enter commands from Appendix C, ASCII Command/Response
Structure.
Note: The Default administrator username/password for a new system is admin/admin. Upon
logging in, the administrator should create a new username/password via command
ADU, described on page C-3. After a successful creation of the new user, the system
administrator should logout from the Terrasat default username, login to the newly
created user and delete the Terrasat username via command DLU on page C-25.
! CAUTION
Do not delete the default username before creating your new personalized
username.
Do not delete an IBUC user while logged into it.
Note: One might change the current username password via CPS command, described in
detail on page C-21.
Multifunction LED
The multifunction LED is mounted on the Cyber Hardened IBUC 2, IBUC 2e,
IBUC 2G, IBUC R and IBUC G housing and provide visual indications of IBUC
status. LED colors and modes are as follows:
• Flashing Green - No alarms

• Flashing Red - Minor alarm being reported
• Steady Red - Major alarm being reported
5-2 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Monitor and Control Features
Certain alarms are configurable meaning that you define them as major or minor
alarms when thresholds you set are exceeded. Major alarms will cause relay closure
(Form-C). The alarms shown in Table 5.1 are the factory default configuration.
Thresholds for alarms that are user configurable can be set by using any of the M&C
interfaces described in this chapter.
Table 5.1 Default Alarm Configuration

Alarm State
Major Minor None
Flashing Red
Configurable
Solid RED
Log Only
User
Tx Alarms
DRO out of lock No X
Tx Output Level High Yes X
Tx Output Level Low Yes X
Tx Input Level High Yes X
Tx Input Level Low Yes X
High Temperature Alarm Yes X
Tx Simulated Fault No X
10 MHz Reference Fault No X
Input Voltage Out of Range No X
Switch Fault No X
Input Current Out of Range No X
AGC/ALC Target Out of Range No X
AGC/ALC Out of Range No X
Overdrive Alarm No X
Tx Muted Alarm No X
To disable the multifunction LED use the ASCII command CLE on page C-15.
Ethernet
Using Ethernet, you can communicate with the IBUC 2, IBUC 2e, IBUC 2G,
IBUC R or IBUC G through SSHv2, SNMPv3 or through the onboard Web Server
(HTTPS). The IBUC uses a static IP addressing structure and does not support DHCP
(Dynamic Host Control Protocol).
The IBUC is configured at the factory, as follows:
IP Address 192.168.1.21
M&C Interfaces | 5-3

IP Gateway 192.168.1.1
Subnet Mask 255.255.255.0
Note: Your computer should have a static IP address on the same subnet as the IBUC. Using
a suitable cable, connect the computer to the J2 connector on the IBUC.
Determining the IP Address of Your IBUC

Due to the lack of support of DHCP, the IBUC IP address will not change after
configuration. In the event that such IP address is not known by the user, it is
recommended the usage of Wireshark® network packet analyzer for IP discovery.
SSHv2
SSHv2 enables you to connect to another computer by using a SSHv2 client from the
host PC. The default port for SSHv2 is 22. Characters are echoed back to the user. The
response is terminated with ‘IBUC>’. To initiate a session;
1. Activate a SSHv2 client program from the host computer such as PuTTY.
2. Configure SSHv2 Session with SSH port and IP address. Connect to the IBUC
unit.
3. At the “IBUC Login” prompt enter the username. A default banner will be
displayed followed by the “Password” prompt.
4. Enter the previously defined password. After this step, the user should see the
“IBUC>” prompt.
You can now use the ASCII commands to configure and monitor the IBUC. For more
information, see Appendix C, ASCII Command/Response Structure.
Note: The default administrator username/password for a new system is admin/admin.
By Default: Username: admin | Password: admin
Upon logging in for the first time, administrators will be forced to change their default
passwords.
Note: Since this is a safety feature, we highly recommend every user, but especially
administrators, change their default passwords as soon as possible.
All users will be forced to change their default passwords upon logging in for the first
time.
The Administrator may choose between keeping his default account or creating
another new Admin account and delete the default one.
To create a new Administrator username/password, use the command ADU, described

on page C-3. After successful creation of the new user, the system Administrator
should log out from the Terrasat default username, log in to the newly created user and
only than, delete the Terrasat’s default username.
To delete an user name, use the command DLU on page C-25.
! CAUTION
Do not delete the default username before creating your new personalized
username.
Do not delete an IBUC user while logged into it.
Exeption: Even if not recommended safety-wise, in some cases, an administrator may be allowed
to create new users while still using the default password. In these cases, Administra-
tors will be forced to change their default password right after that, or upon their next
login.
Note: Changing the passwords is only available on the SSH/serial port sessions. Please con-
sider setting the unit using these interfaces first rather than the web pages.
Note: One might change the current username password via CPS command, described in
detail on page C-21.
SNMPv3
The IBUC supports SNMP version 3.0 protocol. The SNMPv3 agent listens on Port
161 for SNMP messages and uses Port 162 for transmitting Trap information. These
Traps are configurable alert messages and might report an specific event. SNMPv3
can be configured from the RS232 and SSHv2.
The following commands configure SNMPv3 operation on the IBUC:
IBUC R or IBUC G by using either RS232 or SSHv2.
2. Make sure that both SNMPv3 interface and SNMPv3 Trap functionality are
disabled. To disable SNMPv3 interface use the CIS command described on
page C-14. To disable SNMPv3 Trap functionality use the command CIHD on
page C-13.
Note: Terrasat, Inc. Cyber Hardened IBUC’s come with two preconfigured SNMPv3
users. The first is “auth_no_priv”, which is destined for read-only access levels.

The second user is “auth_priv”, which is used for read-write operations. Both users
configurations are further described below:
“auth_no_priv”
• Username: auth_no_priv
• Authentication: SHA
• Auth. Password: 12345678 (default)
“auth_priv”
• Username: auth_priv
• Authentication: SHA
• Auth. Password: 12345678 (default)
• Encryption: AES
• Priv. Password: 12345678 (default)
3. (Optional) If SNMPv3 Trap functionality is required configure Trap Target IP

Address by using command CIHA on page C-12.
! CAUTION
If Trap functionality is required, do not delete “auth_priv” user as mentioned on
Item 4.
Note: Trap service is configured to use “auth_priv” as default SNMPv3 user, hence, it
will use the same configurations as “auth_priv”.
• Engine ID: 0x10203040
• Trap Username: auth_priv
• Authentication: (same as user)
• Auth. Password: (same as user)
• Encryption: (same as user)
• Priv. Password: (same as user)
4. Although both preconfigured SNMPv3 users might provide all of the expected
functionality, the user is encouraged to create new SNMPv3 users with non-
publicly shared Authentication and Private passwords. Use the features described
on SNMP User Configuration on page B-28 to manage SNMPv3 users.
Note: It is recommended that a new SNMPv3 user is created before deletion of the
default users. Many security breaches happen due to misuse of default passwords
or open sessions.
Change the username and passwords as soon as the unit is set up.
5. (Optional) If the default SNMPv3 Views and Groups do not provide all of the
expected functionality, the user may create new Views and Groups by usage of
SNMP Groups.
6. Enable both:
• SNMPv3 interface via CIS command on page C-14 and
• SNMPv3 Trap functionality via CIHA on page C-12.
! CAUTION
Do not disable SSH and Web by accident at the same time.
If SSH and Web are disabled, only serial port can turn them ON.
MIBs
Management Information Bases (MIBs) are hierarchical virtual databases used to
manage the devices in a communications network. The following MIBs are provided
for the SNMPv3 management station:
• SNMPv2-MIB
• HOST-RESOURCES-MIB
• TERRASAT-MIB
• TERRASAT-SMI-MIB
• SNMP-FRAMEWORK-MIB
• SNMP-MPD-MIB
• SNMP-USER-BASED-SM-MIB
• SNMP-VIEW-BASED-ACM-MIB
• SNMP-TARGET-MIB
• SNMP-NOTIFICATION-MIB

Embedded Web Pages

Current IBUC configuration and status information also can be accessed via the
Embedded Web Pages. Although this method does not provide all of the
administrative privileges, such as user creation and deletion, it is the most intuitive for
overall IBUC management.
To access to Embedded Web Pages, open any Web browser and type the IP address of
the IBUC. A login page then appears. After login, the user will have a choice of eight
Web Pages with IBUC status, control, alarm information and live charts. Individual
pages are displayed from the selection of the three main drop-down menus.
For more information about the options available on each Web Page, see Appendix B,
Embedded Web Pages.
Power Measurement
The Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC G are capable
of accurately reading the input and output power for a single carrier in either
continuous signal mode (CSM) or in burst mode. The dynamic range for input power
is from -55 dBm to -20 dBm and for output power the dynamic range is from rated
power to 20 dB below rated power. Each unit is loaded with a detector calibration
lookup table that compensates for detector variations in frequency, power level, and
temperature. The reported power level is then based on the user-requested frequency
and the internally monitored temperature and power level. If multiple carriers are
present, the composite transmit power level is read but accuracy is dependent upon the
actual carrier frequencies, levels, and modulation being used.
The power measurement occurs in the following two ways:
1. Burst Mode
In burst power measurement mode it is assumed that, in normal operation, a
transmit carrier may or not be present due to the nature of burst mode operation.
Since the transmit burst pulse has a rise time and a fall time and the envelope level
varies during symbol transitions when the signal is modulated, the power must be
reported as a peak value. To maintain detected accuracy of the burst pulse, 128
consecutive measurements of the pulse are taken. Once the initial reading exceeds
the burst threshold, 128 consecutive readings are taken (regardless of level). The
highest value of the 128 is displayed. The IBUC reports the most recent valid
reading above the burst threshold.
Burst Time: 500 µs to 1 s
Measurement accuracy: ±2 dB absolute, 1.5 dB p-p relative. Accuracy is improved
as the burst threshold setting is raised closer to the carrier peak.
The detector accuracy is based on a pulsed unmodulated signal with a pulse width
of 500 µs.
2. Continuous Signal Mode (CSM)

In CSM power measurement mode, it is assumed that, in normal operation, a
transmit carrier is always present. Therefore, reported power is the peak power
over 128 consecutive readings.
Measurement accuracy: ±1 dB absolute, 1 dB p-p relative*
The detector accuracy is based on a CW unmodulated carrier.
* Relative measurement accuracy defines the error between any two power
readings at any particular frequency over the dynamic range.
Notes: To make the given accuracy achievable, the operating transmit frequency
information must be provided via M&C in order to use the information in the
detector’s internal calibration look-up table.
By default, the unit will be set to perform CSM measurements.
Input Power Overdrive Protection

To ensure that output stage transistors achieve saturation, and thus, maximum
performance, the Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC
G allow for input overdrive. Input overdrive point allows for 6 dB overdrive at 0 dB
attenuation above the expected saturation point. As excessive saturation could damage
Gallium Nitride FET (GaN) based units due to unsustainable heat levels within the
device, a input overdrive protection algorithm is employed to protect power
amplifiers.
Such algorithm takes advantage of the IBUC’s input and output power readings to
drive internal attenuators, changing input drive level to achieve protection. This
feature ensures input overdrive protection without adverse effects to operations
outside the BUC. Input overdrive protection depends on the selected operation mode.
The three possible operations modes are: Open Loop, AGC, ALC.
Power Measurement | 5-9

1. Open Loop Operation

In Open Loop Operation, input overdrive point changes based on the user input
attenuation. Once the input overdrive condition occurs, every 1 dB increase of the
input level causes a 1 dB increase in attenuation. If the input level exceeds -15
dBm the algorithm increases the attenuation to maximum.
2. AGC Operation
In AGC Operation, input overdrive point changes based on both user input
attenuation and any attenuation applied by the AGC loop. Once the input overdrive
condition occurs, every 1 dB increase of the input level causes a 1 dB increase in
attenuation. If the input level exceeds -15 dBm the algorithm increases the
attenuation to maximum.
3. ALC Operation
ALC Operation uses no input protection. The output level is automatically
controlled by the attenuators. As the input level increases, ALC attenuates to
maintain the same level.
6
C HAPTER
TROUBLESHOOTING
CHAPTER6
This chapter discusses basic troubleshooting procedures for the Terrasat

Communications, Inc. line of intelligent block upconverters (Cyber Hardened IBUC 2,
IBUC 2e, IBUC 2G, IBUC R and IBUC G) and outdoor units (ODUs).
Maintenance
In general, Terrasat power supply units (PSUIs) and ODUs are self-contained and
require little maintenance. However, for optimum performance, Terrasat recommends
that users inspect the mechanics of the system quarterly and perform the following:
• Clean the antenna feeds to keep them clear of obstructions.

• Check cables and connectors for signs of wear, damage, or loose connections.
• Check all fan intakes and exhausts to ensure that they are clear of debris. The user
can use a water hose for this purpose while the unit is off.
Transceiver Fault Isolation

Use the information in this section to assist in determining whether a Terrasat unit is
faulty. The intent is to determine a “Go” or “No Go” situation based on alarms
indicated through the M&C ports, as well as by measuring certain signals using test
equipment.
AC Power Problems/Conditioning
In today’s electrical environment, there are many types of power-related problems that
can prevent proper operation of sensitive electronic equipment. These problems or
disturbances can be caused by things such as voltage induced by lightning, switching
high-power electrical equipment On/Off, or utility company actions such as power
factor correction. Serious problems can arise with the occurrence of transients and
spikes which can cause random errors or even failure of the circuitry.
Whatever the origin of the transients, they can be classified into two simple categories:
• Common Mode
Noise voltage that appears equally and in phase from each signal conductor to
ground. (The term “common” refers to the fact that identical noise appears on both
the active and neutral wires.) Common-mode noise poses a threat because the
noise attempts to dissipate its energy from neutral to ground or from active to
ground.
• Normal Mode
Noise potential between the power line conductors. It adds to and subtracts from
the power line sinusoidal voltage wave and is sometimes referred to as
differential-mode noise or transverse-mode noise. Normal-mode noise attempts to
dissipate its energy along any path from line to neutral. If the normal-mode noise
has sufficient voltage (or energy), damage can occur.
Category A
At the wall outlets (and more than 30 ft. [9 m] from a distribution panel), the typical
noise is a 0.5 s rise time up to 6 kV peak open circuit voltage, 100 kHz ring wave
with 200 ampere short circuit current capability.
Category B
At the distribution panel, one can experience the 100 kHz ring wave listed previously
but with 500 ampere current capability and a unidirectional impulse up to 6 kV
potential rising in 1.2 s and decaying to half voltage in 50 s. Accompanying this can
be a short circuit current up to 3000 amperes rising to peak in 8 s and decaying to
half value in 20 s.
To ensure uninterrupted service, Terrasat recommends using a line conditioner or

uninterruptible power supply (UPS) based on the expected AC power at the site.
Site-Related Problems
VSAT antennas are often fitted at the top of buildings. Avoid close proximity to
elevator motors, and such. Ensure that the satellite signal path is free and clear of
obstructions.
M&C Checks
When troubleshooting the IBUC, the first level of troubleshooting should be to check
the status through the M&C port. Events and an event history log are available with
the IBUC M&C. For specific information about using the RS232 or Ethernet ports, see
Chapter 5, Monitor and Control Features.
6-2 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Troubleshooting
Power Supply Checks

Before beginning RF troubleshooting of DC-powered IBUCs, first verify that the
proper voltages are being supplied to the IBUC. Input DC voltage and IBUC current
consumption data are available from the IBUC M&C. Verify that the values are within
limits. If an M&C interface is not available, use a multimeter to verify that the
appropriate voltages (24 VDC or floating 48 VDC) are present at the IBUC. Check the
part number label on the IBUC to determine the required voltage. The IBUC DC
supply can be through either the J1 or J3 connector.
Transmit Power Setting

There have been several cases reported to Terrasat Technical Support where the
transmit power has been turned up to or near saturation while transmitting a digital
carrier. This most likely will result in spectral distortion, re-growth, and
intermodulation products for multi-carrier operation. To reduce saturation, reduce the
input level or increase the attenuation.
Note: When transmitting digital carriers, it is customary to operate the power amplifier
system with an output back off (OBO) sufficient to meet the spectral density mask
requirements and interference requirements of multi-carrier operation.
Transmit Intermediate Frequency Input Level Verification

If low or no Tx output power is detected, begin troubleshooting by checking the input
to the IBUC.
! WARNING
DC power might be present on the cable. Terrasat recommends the use
of a DC block.
1. Check the Tx Input Level displayed in M&C or disconnect the cable at the IBUC
J1 connector (Tx L-band) and use a spectrum analyzer to measure the power level
of the L-band signal at the output of the coaxial cable that connects to the IBUC at
J1 (Tx L-band). The L-band signal level should be within the range of -20 dBm
through -55 dBm. If it is not, check the cable and modem output.
2. If the L-band signal is within range, check that the 10 MHz reference signal is
within the range of +5 dBm through -12 dBm and is distortion free. If it is not,
check the cable and modem output.
3. For DC-powered IBUCs, if the L-band and 10 MHz signals are good check that
the DC voltage level is within range. The DC voltage may be on the L-band IFL or
Maintenance | 6-3
from a separate power supply for 16 watts Ku-band, 25 watts C-band, or 20 watts
X-band and lower power units. For higher power units, the DC voltage will be on
the DC cable that is connected to the IBUC DC Input (J3 connector). If it is not,
check the PSUI or modem power supply outputs and cables.
4. For DC-powered IBUCs, if the L-band, 10 MHz and DC voltage signals are within
range, continue with the IBUC Tx Output verification procedure that follows.
5. Disconnect the spectrum analyzer from the coaxial cable.
Cyber Hardened IBUC 2 Transmit Output Verification

This check assumes that the L-band, 10 MHz, and DC inputs (for DC-powered
IBUCs) are at the correct levels.
1. Tx Output level is monitored and displayed in the IBUC M&C. Alternatively, you
can connect a waveguide-to-coaxial adapter and a 40 dB high-power attenuator to
the IBUC Tx waveguide output.
2. Measure the Tx RF output with the spectrum analyzer connected at the waveguide
output. Ensure that the cable loss of the cable being used for the measurement has
been taken into account.
3. RF power should be between rated power and no lower than 25 dB below rated
power. If it is not, the IBUC is defective and should be returned to the factory for
repair. Instructions for returning a unit for repair are on page 6-8.
4. IF the IBUC Tx RF output measures within specification, ensure that the
waveguide, feedhorn, and antenna are properly aligned.
Receive L-band Output Verification

If low or no RF output power is detected, begin troubleshooting by checking the
output of the LNB.
1. Ensure that 15 VDC to 24 VDC (LNB Bias) is present at the modem Rx Input
using a digital voltmeter (DVM). If it is not present, check the cable and modem.
2. Use a spectrum analyzer to ensure that the 10 MHz signal is present at the modem
Rx Input. If it is not, check the cable and modem.
! WARNING
Since DC power might be present on the cable, Terrasat recommends
the use of a DC block.
3. Connect the LNB to the demodulator by attaching the coaxial cables from the Rx
L-band Out on the LNB to the demodulator Rx L-band input port. If the Rx level is
low, check the cable, the feedhorn, and the antenna for proper operation.
Common Problems
The following problems or occurrences have been noted during normal
troubleshooting.
Tx Output is Disabled
When the Tx Output is set to Disabled, the Tx Output level shown on the Sensors on
page B-25 reads -99.00 dBm. This is not an actual reading.
However, when conditions cause the automatic shut-off of the Tx Output signal, the
Tx Output is muted and the Tx Output level on the Sensors on page B-25 reads
-96.00 dBm.
Incorrect Frequency Settings

If the Satellite Network Operations Center (NOC) does not recognize your signal, see
page 4-8 for additional information.
Damaged Cables
RF coaxial cable damaged due to improper handling (such as contact damage due to
improper mating; cable insulation that is damaged, crushed, cut, or charred; cables
were not discharged prior to connecting them; or conductors that are nicked, gouged,
damaged, or severed) may impair system performance and reliability. Do not attempt
to repair broken or damaged coaxial cables unless absolutely necessary. Replace the
entire cable whenever possible.
Damaged cabling and incorrectly tightened connectors can leak RF energy, which may
lead to excessive levels in their immediate vicinity.
! CAUTION
Never disconnect RF cables or connectors associated with a transmitter
in operation since this may result in an RF burn through direct contact
with RF conductors.
Maintenance | 6-5
10 MHz Reference Signal is at the Wrong Level or Missing

A 10 MHz input is used to provide a stable reference frequency to which the
phase-locked local oscillator (or PLDRO) synchronizes. The 10 MHz reference signal
level should be between -12 dBm to +5 dBm.
When the IBUC senses that the phase-locked local oscillator has gone out of lock, a
PLDRO Lock alarm is triggered. This alarm then initiates a series of routines that
leads to the muting of the power amplifier (that is, the IBUC is automatically shut-off).
Table 6.1 lists four possible scenarios caused by changes in the 10 MHz reference
signal or whether the PLDRO is locked.
Table 6.1 Possible Scenarios for IBUCs with an External 10 MHz Reference Signal
10 MHz Reference Phase-Locked Local

Results
Signal Level Oscillator
Causes a minor alarm (10 MHz Detector). Unit
Low Locked is still transmitting. Check the 10 MHz signal
level. Resultant phase noise may be degraded.
Causes a major alarm (PLDRO Out of Lock).

Power amplifier is muted and the IBUC is
Low Out-of-Lock automatically shut-off. Check the 10 MHz
reference signal level and whether the 10 MHz
reference signal is enabled at the modem.
Unit is operating normally. No alarms are

Within Specifications Locked
present.
Causes a major alarm (PLDRO Out of Lock).

Power amplifier is muted and the IBUC is
Within Specifications Out-of-Lock automatically shut-off. PLDRO may be faulty
and the IBUC might need to be returned for
repair.
Antenna is Pointed Toward Wrong Satellite or is Misaligned

Transmission to the wrong satellite or on the wrong polarization or channel can cause
interference with other satellite users and may result in fines from the satellite
operator.
To ensure that your antenna is aligned with the correct satellite,
1. Follow the antenna manufacturer’s instructions to verify the azimuth, elevation,

and polarization settings.
2. Follow the antenna manufacturer’s instructions to move the antenna into a position
that provides maximum signal strength.
3. Establish a communications link with the satellite network operations center
(NOC).
4. Peak the signal on the satellite, and then adjust polarization per guidance from
NOC staff.
Moisture Migrated Into the Cyber Hardened IBUC

Moisture can enter and damage the IBUC if waveguide gaskets are missing, there is a
hole in the feed window, or there is a break in the coaxial connectors.
To prevent moisture from entering the IBUC,
• Ensure that the paper label is removed from the waveguidre prior to installation
and operation.
• Ensure that the rubber waveguide gasket is intact and fully seated in the grooved
channel before making the connection.
• Use water-resistant wrap (or mastic tape) on all outdoor connectors to ensure a
water-tight seal. Mastic tapes are designed to flow and self-heal if cut or punctured
For more information about applying water-resistant wrap, see page 3-18.
• Avoid using damaged connectors (for example, scratched mating surfaces,
eccentric or bent center conductors, and so on.).
• Seal all coaxial cable fittings with putty.
Bad Orthogonal Mode Transducer and/or Antenna

If the antenna feedhorn and orthogonal mode transducer (OMT) are not positioned
correctly, the IBUC will not operate properly.
To position the feedhorn and OMT,
• Refer to the antenna manufacturer’s assembly instructions to verify that the

feedhorn and OMT were mounted correctly on the antenna.
• Establish a communications link with the satellite network operations center
(NOC).
• Guided by NOC staff, slowly rotate the outdoor equipment to the appropriate
position.
• If rotation is impossible, it is likely that there is a problem with OMT and it will
need to be returned to the antenna manufacturer.
LED is Red
A red LED indicates only that a fault (or alarm) has occurred and does not necessarily
indicate that transmission has stopped. A flashing red light indicates a minor alarm and
a solid red light indicates a major alarm. You can communicate with the IBUC to
determine what is causing the fault, and then clear the fault condition.
Maintenance | 6-7
1. Establish a connection with the IBUC by using any of the M&C interfaces.
2. View the Alarm Status Tab (shown on page B-9) to determine the current alarm.
3. View the Sensor Tab (shown on page B-25) to determine which sensor reading
caused the alarm.
4. Compare your readings to the thresholds.
5. Adjust the threshold level(s) to bring the reading(s) within specifications and thus
clear the fault
When the fault is cleared, the LED should be flashing green.
Repair Policy
The Terrasat Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G and
PSUI are not field repairable.
In the event that a failure has been detected, it might be necessary to return the
defective unit to the factory or a factory-authorized service center. The following
section contains instructions for returning a defective unit to the factory for repair.
Returned Material Authorization (RMA)

If any equipment is determined to be defective:
• Have the following information available:

• Unit serial number
• Unit part number and description
• Complete description of the failure
• Designated contact name and phone number
• Billing information
• Shipping information
• Contact Terrasat Customer Service to request an RMA number.
• Telephone: +1 408.782.5911
• E-mail: [email protected]
• Properly package the defective equipment in its original container (if available and
undamaged), and mark the RMA number on the outside of the shipping container.
Note: Do not return any equipment without an RMA number.
• Ship the equipment to the following address:

Terrasat Communications, Inc.
315 Digital Drive
Morgan Hill, CA 95037
U.S.A.
• After the unit is received at Terrasat, an initial evaluation will be performed.
• If the unit is found to be in-warranty, the unit will be repaired and returned at
no charge.
• If the unit is found to be out-of-warranty, Terrasat Customer Service will
contact the designated contact for authorization to proceed with the repair.
• Authorization in the form of a purchase order will be required.
• Once authorization is received, the unit will be repaired and returned.
Repair Policy | 6-9

A
A PPENDIX
PART NUMBERING SCHEMA

CHAPTER0
The charts in this appendix illustrate the part numbering schema used for Terrasat
Communications, Inc. Products.
Identifying the Part and Serial Numbers

Figure A.1 illustrates the difference between the unit’s part number and serial number.
Figure A.1 Identifying the Part and Serial Numbers
Decoding the Part Number

Use the charts on the following pages to help determine the information contained in
the part number about your specific unit.
BUC SIZE
SPECTRAL INVERSION IF INPUT T IBUC 3 size (7 x 5)
& 10MHZ REFERENCE CONNECTOR D IBUC 2 size (10.5 x 6) TX OUTPUT

0 Non-Inverting & F F-Type U IBUC original size OPTIONS
External10MHz Connector (12.2 x 7.2) A Waveguide to N-Type
Adapter
FAMILY 1 Inverting & External 10MHz N N-Type Q IBUC HP size (16.2 x 10)
(CONTROLLER & LO) 2 Non-Inverting & Internal Connector C Ku IBUC R/G size (23 x 10) N N-Type
10MHz SPECIAL OPTIONS
B - IBUC Cyber Hardened T TNC S C/X IBUC G size (24 x 10) W Waveguide
Controller & PLDRO LO 3 Inverting & Internal 10MHz Connector N IBUC VHP size (29 x 15) P PBR-Style Waveguide 00 No special Options
FREQUENCY OPERATING POWER TECHNOLOGY & COLOR SPECIAL

BAND VOLTAGE LEVEL LINEARIZER OPTIONS SPECIFICATIONS
050052 GlobalStar C-Band 2 Floating 24 VDC / Power via 004 - 4 watts S GaAs B Black 00 Standard
057064 Low C-Band Coax 005 - 5 watts T GaN 24V & No Linearizer D Dark Green Specifications
058064 Standard C-Band 4 Floating 48 VDC / Power via 008 - 8 watts U GaN 24V & Linearizer E Bronze Green
058066 Extended C-Band Coax 010 - 10 watts F GaN 48V & No Linearizer G Green
058067 Full C-Band 5 Floating 48VDC / No Power 012 - 12 watts G GaN 48V & Linearizer I Actia Desert Tan
064067 Palapa C-Band via Coax 016 - 16 watts K Khaki
067070 Insat C-Band 6 18-75 VDC Input / Power via 020 - 20 watts L NATO Green (Powder)
079084 X-Band Coax Only 025 - 25 watts M NATO Green (IR 24x5)
127132 Low Ku-Band 3 7 48 VDC Input / Power via 030 - 30 watts P Dove Gray
128133 Low Ku-Band 4 Coax Only 040 - 40 watts Q Sand
137145 Full Ku-Band 8 Floating 48 VDC Input/ No 050 - 50 watts R Platinum Gray
140145 Standard Ku-Band Power via Coax Only 060 - 60 watts T Tan
148151 High Ku-Band A AC Input Std. Connector 080 - 80 watts Y Yellow Sand
290300 Ka-Band 3 (C016 20C003 100 12) 100 - 100 watts W White Textured
295300 Ka-Band 1 B AC Input MilSpec Connector 125 - 125 watts A Gray Beige
300310 Ka-Band 2 (MS3102E16-10P) 150 - 150 watts S Desert Sand
305310 Ka-Band 4 C AC Input MilSpec Connector 175 - 175 watts C Desert Tan
(H/MS3106A22-22P-D-T(73) 200 - 200 watts
300 - 300 watts
400 - 400 watts
Figure A.2 Part Numbering Schema for Cyber Hardened IBUC
A-2 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Part Numbering Schema
OPERATING COLOR SPECIAL

POWER SUPPLY POWER OPTIONS
VOLTAGE OPTIONS OPTIONS
9 Outdoor 24 24 VDC
11 600 watts Indoor 47 48 VDC
12 1000 watts Indoor
Figure A.3 Part Numbering Schema for Cyber Hardened IBUC with PSUI Systems
Decoding the Part Number | A-3

A-4 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Part Numbering Schema
B
A PPENDIX
EMBEDDED WEB PAGES

CHAPTER0
The embedded Web pages shown in this appendix are a user-friendly way to access
the various monitor and control (M&C) features offered by the Cyber Hardened
IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC G.
Some of the screen shots from the Web interface shown in this appendix are under
development and may appear slightly different from the actual ones.
Introduction
To access the embedded Web pages,
1. Connect the host computer’s Ethernet cable to the Cyber Hardened IBUC 2,
IBUC 2e, IBUC 2G, IBUC R or IBUC G J4 pin header.
! CAUTION
For Cyber Security reasons, we support and recommend “HTTPS” for firmware
upgrade. Please, always use “https://<IP address>” for the URL instead of “http:/
/<IP address>”.
Note: Steps 2 through 8 will guide the user on how to setup the host PC for the first
access to the Cyber Hardened IBUC embedded web pages. Despite this process
being shown on a Windows machine, the process can be achieved on other
Operating Systems.
2. On Windows Operating Systems, open the Start Menu by pressing the Windows
icon and then search for “Control Panel” in the search bar.
3. Navigate to “Network Connections > Network and Sharing Center > Change
Adapter Settings”.
4. Right Click on Ethernet Connection Icon and select “Properties”.
The Local Area Connection Status window shown in Figure B.1 appears.
Figure B.1 Ethernet Properties Window

5. In the dialog window, scroll down until “Internet Protocol Version 4 (TCP/IPv4)”
becomes visible select it.
6. Click Properties.
The window shown in Figure B.2 appears
B-2 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Embedded Web Pages
Figure B.2 Choosing the Internet Protocol (TCP/IP) Properties

7. Select “Use the following IP address,” and set the IP Address to 192.168.1.100 and
an appropriate gateway.
Introduction | B-3
Figure B.3 Host IP Address Configuration

8. Click OK.
9. Using the host computer, activate a Web browser window.
10. To open the Embedded Web Pages, access https://192.168.1.21
11. Within a few seconds, the Login page shown in Figure B.4 on page B-5 will
appear.
Note: Since the embedded web pages are served using a self signed certificate, a warning
will be issued saying that the web pages are not digitally signed. Terrasat Inc. is
working with third parties to get the certificates signed and this message will go away
in future. Click the option to proceed to the website.
Web Pages Menu Tree

Log In
Once connected via Web Browser to a Cyber Hardened IBUC unit, the Login web
page should appear. Type your password in the dialog box, and then click Login. The
default username/password is admin/admin. If the login password that you entered is
accepted, the Information page will appear, else a message to re-enter the username
and password will appear.
Figure B.4 Login Tab
! CAUTION
For full usage of the Security features, the system administrator is highly
advised to create a new user and delete the default user provided by Terrasat.
Web Pages Menu Tree | B-5

Responsive Design
If remote access to the IBUC is needed, the Embedded Web Pages can be viewed on a
mobile device or tablet. Due to its responsive design, the web pages will adjust
automatically to the device’s screen resolution, allowing for easy navigation and
control.
Figure B.5 Mobile view of the Embedded Web Pages
Configuration Menu
Information
Use this page to view read-only data such as the model number, serial number,
revisions, and frequencies for the Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G,
IBUC R or IBUC G.
Figure B.6 Information Page

From this page, you can view the following parameters:
• Model Number
Displays the model number of the IBUC. More information about the data
contained within the part number is found in Appendix A.
• Serial Number
Displays the unique serial number of the IBUC.
• Firmware Version
Displays the version number. The firmware version number of the IBUC is used
mainly by Terrasat Technical Support personnel.
• Hardware Version
Displays the version number of the hardware.
Note: The hardware version can be updated only when the IBUC is returned to the
factory.

• Tx Rated Power
Displays transmitter output power at 1 dB compression. Tx rated power
information is contained within the part number. More information about locating
the power level of the IBUC is found in Appendix A.
• Frequency Band
Displays the standard name of the band.
• RF Frequency Range
Displays the valid RF frequencies for the IBUC. The RF Frequency range for each
of the various IBUC bands is listed in Table 2.1 on page 2-3 through Table 2.5 on
page 2-7.
• IF Frequency Range
Displays the valid IF frequencies for the IBUC. The L-band IF Frequency range
for each of the various IBUC bands is listed in Table 2.1 on page 2-3 through
Table 2.5 on page 2-7.
• LO Frequency
Displays the valid LO frequencies for the IBUC. The LO Frequency for each of the
various IBUC bands is listed in Table 2.1 on page 2-3 through Table 2.5 on
page 2-7.
• Spectral Inversion
Options include:
• Non-Inverted
• Inverted
When inverted, the relationship between the RF and IF frequencies is inverse;
that is, if the modem frequency lowers, the RF frequency increases and vice-
versa.
• Total System Hours
Displays the total number of hours that the system has been operating, that is, the
total number of hours that the system has been powered on. This accumulates after
cycles (imagine it like a odometer of a car).
• Total Tx Enabled Hours
Displays the total number of hours that the transmitter has been enabled (that is,
with transmit = On and mute = Off).
• Internal 10 MHz
Indicates whether the IBUC has the internal 10 MHz optional installed or not.
• Supply Voltage
Displays the power supply voltage range for which the IBUC was designed. The
Supply Voltage Range is based on the configuration of your IBUC.
User Configuration
Here the operator can view all current users registered by the system (see Figure B.7),
add more users (Figure B.8) or delete existing users (Figure B.9). A registered user is
composed of three main informations:
• Username: String of characters indicating the name that identifies the User. This
field can contain up to 32 characters.
• Privilege: Defines the access the user has. Can assume one of two values: ‘admin’
or ‘user’
• Password: String of characters indicating the password this User requires to access
the unit. This field can contain up to 32 characters.
Figure B.7 Cyber Hardened IBUC Users

From the main User Tab, the operator is able to add more users by pressing on the
“Add” button or delete existing users by pressing the “Delete” button.
Figure B.8 Add Cyber Hardened IBUC User

The operator is not able to directly change user passwords via the Embedded Web
Pages. This goal can be achieved by one of two methods:
• Using the provided ASCII command ADU on page C-3, or CPS on page C-21.

• Deleting and re-creating a user with a different password using the Embedded
Web Pages.
Figure B.9 Delete Cyber Hardened IBUC User
Transmit Configuration
Use this page to configure transmission operating parameters for the Cyber Hardened
IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC G. Click Submit when you have
completed entering data to ensure that your changes are saved and then implemented.
Figure B.10 Tx Configuration Tab
From this page you can configure the following parameters:
• Tx Output
Select whether the unit is actively transmitting. Options include:
• Enabled
• Disabled
• Power Monitor Frequency
Sets the Power Monitor Frequency which is the actual frequency at which you are
operating. To ensure accurate readings, you must set your operating frequency
which might be different from the factory default values listed in Table B.1.
Example: If the frequency allocated to you by the satellite carrier is 6400 MHz, set
the Power Monitor Frequency to 6400 MHz.
The factory default values in Table B.1 are listed according to the model number
of the IBUC. For more information about identifying the model number of the
IBUC, see Appendix A, Part Numbering Schema.
Table B.1 Default Values for Power Monitor Frequency

Model Number Default Value Model Number Default Value
050052 5100 128133 13050
057064 6075 137142 14000
058064 6137 137145 14125
058066 6250 140145 14250
058067 6287 173181 17700
064067 6575 181184 18250
067070 6875 290300 29500
079084 8150 295300 29750
127132 13000 300310 30500
• Tx State at Power-Up
Sets whether the unit is transmitting upon power-up. Options include:
• Enable
• Disable
• Tx Power-Up Delay
Sets the transmit power output delay of the IBUC in seconds. When configured,
the Tx Output will be muted for the period specified before beginning to transmit.

• Power Read Mode

Sets the mode in which power is read. Options include:
• Burst
In burst mode, the input signal is active only a small percentage of the time
because packets of data are sent in bursts.
• Continuous
In continuous mode, the input signal continues without interruption.
• Burst Timeout
Sets the longest allowable time between valid data bursts before the IBUC reports
an alarm. This command applies when the IBUC is set to burst power monitoring.
The set value must be between 0 and 300 seconds. 0 is the default value (No
Timeout).
• Burst Threshold
Sets the burst threshold for the IBUC. This value determines the level at which a
burst is considered valid. The threshold is for the output power level; the threshold
for input power is configured internally.
The value must be between rated power and no less than 2 dB below rated power.
Default values are listed in Table B.2.
Table B.2 Default Values for Burst Threshold

Power Level Default Value Power Level Default Value
004 16.0 050 27.0
005 17.0 060 28.0
008 19.0 080 29.0
010 20.0 100 30.0
012 21.0 125 31.0
016 22.0 150 32.0
020 23.0 175 32.4
025 24.0 200 33.0
030 25.0 300 35.0
040 26.0 400 36.0
• Gain Mode
Options include:
• Open: no feedback in the measuring loop.
Keep in mind the open-loop gain is affected by temperature and frequency;
however, the temperature compensation feature is still active when the unit
operates with open-loop gain. Open is the default setting.
• Automatic Gain Control (AGC)
• Automatic Level Control (ALC)
Note: The user should not switch directly from AGC/ALC to ALC/ACG. This action
may cause errors. Instead the user should first change from AGC/ALC to Open
Loop gain and then change to ALC/AGC. After Switch from the ALC/AGC Gain
Mode to Open Loop Mode, the user must reset the Gain Control.
! CAUTION
Resetting the ALC/ACG attenuation control might cause abrupt changes of
the Tx Output level. For reduced interference on nearby channels, Terrasat
recommends: attenuating the input signal (via IBUCs internal control),
resetting the gain control, re-adjusting the input signal attenuation until output
power reaches the desired level and finally enabling the desired Gain mode.
• Gain Control Reset

Over time, gain control levels can fluctuate. When the Gain Control Reset option
is enabled, the gain control resets to 0.0 Options include:
• Select (default)
• Reset
Note: You must choose “Reset” and then click Submit in order to reset the gain control.
• Attenuation
Type a value within the range of 0.0 dB to 30.0 dB in 0.1 dB steps. After you click
Submit, the gain of the unit will be reduced by that value.
The default setting is 0.0 dB
• Current Gain Control
Indicates the current gain of the AGC/ALC voltage variable attenuator (VVA)
circuitry. The Gain Control range is 0 dB to 30.0 dB. When the Gain Control Reset
option is selected, this value will reset to 0.0.

• Input Threshold Low

Sets the lowest permitted transmit input value down to -60 dBm. You will receive
an error message if you try to exceed the threshold range. Click OK to return to the
Tx Config page to enter a valid value.
• Input Threshold High
Sets the highest permitted transmit input value up to -15 dBm. You will receive an
error message if you try to exceed the threshold range. Click OK to return to the
Tx Config page to enter a valid value.
• Output Threshold Low
Sets the lowest permitted transmit input value down to (rated P1dB - 20 dB). You
will receive an error message if you try to exceed the threshold range. Click OK to
return to the Tx Config page to enter a valid value.
• Output Threshold High
Sets the highest permitted transmit input value up to (rated P1dB+ 1 dB). You will
receive an error message if you try to exceed the threshold range. Click OK to
return to the Tx Config page to enter a valid value.
• Internal 10 MHz Trim
You can specify a frequency trimming value for IBUCs equipped with optional
internal 10 MHz reference signal.
Valid values: 0-4095
Note: When the IBUC is operating using an external 10 MHz reference signal, this field
is grayed-out and unavailable for user input.
Interface Configuration
Use this page to configure the TCP/IP interface for the Cyber Hardened IBUC 2,
IBUC 2e, IBUC 2G, IBUC R and IBUC G. Click Submit when you have
completed entering data to ensure that your changes are saved and implemented.
Figure B.11 Interface Configuration Tab

• IP Address
Valid values range from (but do not include) 1.0.0.0 through 224.0.0.0. When the
netmask is applied, 0 and 225 in the last byte are excluded.
• IP Subnet Mask
Sets the IP netmask.
• Valid values range from 8 through 30 representing the number of ones in the
netmask. This corresponds to 22.0.0.0 to 255.255.255.252.
• Gateway Address
Sets the IP Gateway Address which is the address that the IBUC will send to if the
requested IP address does not reside on the local LAN segment.
Note: This address cannot be the same as the IP address of the unit.
System Configuration
Use this page to set the system time or NTP Server configurations; and other setting
like the External LED. Click Submit when you have completed entering data to
ensure that your changes are saved and then implemented.
Figure B.12 System Configuration Tab

• Time
Sets the system time of the IBUC in a mm/dd/yyyy hh:mm:ss format.
Note: If “Manual” option is enabled, the user can use the “Time” entry to manually
configure the time settings. If disabled, the IBUC will attempt to connect to a NTP
Server to automatically configure the time and date settings.

• NTP Server Address

Sets the address for the NTP server used to update time and date settings. The
address can be filled out with either the server domain (such as 0.pool.ntp.org) or
its IP address (such as 68.233.45.146).
• NTP Timezone Offset
Sets the timezone offset used to update time and date settings. Only values
between -12:00 and 12:00 are considered valid entries.
• External LED
Sets the state of the multifunction LED indicator. Options include
• Disabled (LED is off)
• Enabled (LED is on)
Enabled is the default setting.
• Reboot Firmware
When selected, this causes a momentary muting of the transmitter and should be
used with caution. A dialog box appears and you are asked to confirm your
selection.
• Enable AC 50 Hz Correction
When enabled, applies a 50 Hz correction factor to AC-powered IBUCs. Options
include:
• Disabled
• Enabled
Disabled is the default setting.
• SSH - Secure Shell (Cryptographic Network Protocol).
Secure Shell administrative interface can be optionally enabled or disabled,
allowing for minimal exposure of interfaces. Limited service exposure enhances
security.
• Web Server
It refers to Web-based configuration. Options included:
• Disabled
• Enabled
Note: If both SSH and Web Server are disabled, then the only way to enable these
features back is by using the serial port. To enable/disable SNMP use as well the
SNMP Dropdown.
• Configure Notice
This feature provides institutions the possibility to display special notices to
potential intruders. One can use it to take legal action against misuse.
The Configure Notice menu allows the system operator to configure a particular
Notice using private standards and personalized text. The system will display the
new message at the login prompt on Serial, SSH, and Web Pages.
• NTP Servers
Up to two (2) NTP servers can be added to allow for redundancy in time
synchronization.

Alarm Configuration
Use this page to configure alarms as Minor, Major, or None. You can also configure
the alarms as suppressible. Suppressible alarms will be suppressed only when the
“Suppress Faults” option is enabled. Click Submit when you have completed entering
data to ensure that your changes are saved and then implemented.
Figure B.13 Alarm Configuration Tab

From this page you can configure the following alarms:
• Temperature
Sets the type of alarm produced when the temperature threshold has been
exceeded. Options include:
• Disable
• Minor
• Major
• Input Threshold Low

Sets the type of alarm produced when the lower Tx Input Threshold has been
• Disable
• Minor
• Major
• Input Threshold High
Sets the type of alarm produced when the higher Tx Input Threshold has been
• Disable
• Minor
• Major
• Output Threshold Low
Sets the type of alarm produced when the lower Tx Output Threshold has been
exceeded. The default lower threshold is equal to rated P1dB - 20. Options
include:
• Disable
• Minor
• Major
• Output Threshold High
Sets the type of alarm produced when the higher Tx Output Threshold has been
exceeded. The default higher threshold is equal to rated P1dB+ 1. Options include:
• Disable
• Minor
• Major
• Temperature Suppressible
Sets whether the temperature alarm is suppressible. When suppressed (enabled), a
temperature alarm will not appear as an event in the Event Log. Options include:
• Disable
• Enable
• Input Threshold Low Suppressible
Sets whether the lower input threshold is suppressible. Options include:
• Disable
• Enable

• Output Threshold Low Suppressible

Sets whether the lower output threshold is suppressible. Options include:
• Disable
• Enable
• Output Threshold High Suppressible
Sets whether the higher output threshold is suppressible. Options include:
• Disable
• Enable
• High Temperature Shutdown
Sets whether to shutdown the IBUC when the internal temperature threshold of
85° C has been exceeded. The unit must cool down by 20° C before resuming
transmission. Transmission will resume automatically once the unit has cooled by
20° C. Options include:
• Disable
• Enable (default)
• Suppress faults
Sets whether the unit will suppress all alarms that are configured as suppressible.
Options include:
• Disable
• Enable
• Simulate faults
When enabled, a simulated alarm is issued that does not affect transmission status
or traffic. Options include:
• Disable
• Enable
Use this alarm to determine whether your alarm settings are functional.
Configuration File
Use this page to download current Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G,
IBUC R or IBUC G Configuration File or to upload it from your computer.
Configuration Files contains information about all of the selections within the
Configuration Menu and SNMP Menu, aiding the user in several manners:
• Automation: By using a Configuration File from a configured unit, the user is able
to replicate it’s configurations to several identical units.
Note: Using configuration files from different Cyber Hardened IBUC models is not
recommended. The usage of such files should be restrained only for identical
models.
• Recovery: In case the user is not sure if the modification of one or more
configurations might cause problems to the units performance, it is advised to
download the Configuration File as a safe recovery point. This way it is always
possible to revert back to known operation conditions by uploading such file.
• Technical Support: In some cases of technical difficulties, the user might be
prompted to download the Configuration File and send it to Terrasat Inc. Technical
Support team for further analysis.
Figure B.14 Configuration File page
Note: The usage of the Configuration File is a feature exclusive to the Embedded Web Pages
and is not available to use via ASCII Commands.

Status Menu
Alarms
Use this tab to verify the alarm status of the unit. Alarm status is indicated with color:
• Green: indicates that the parameter is operating within specifications and no faults
have occurred.
• Yellow: indicates a minor fault.
• Red: indicates a major fault.
• Grayed-Out: indicates that particular parameter is not available for monitoring.
Table B.1 on page B-11 contains the default configuration and lists which alarms
are available for user configuration.
For information about how to configure these alarms, see the Alarm Configuration on
page B-18.
Figure B.15 Alarm Status Tab

• Tx Output
Indicates whether the Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or
IBUC G is currently transmitting. Options include:
• On
• Disabled
• Muted (Alarm)
• Tx Output Low
Indicates whether the Tx Output level is operating below a minimum threshold.
Options include:
• OK
• Major
• Minor
• Tx Output High
Indicates whether the Tx Output level is operating above a maximum threshold.
Options include:
• OK
• Major
• Minor
• Tx Input Low
Indicates whether the Tx Input level is operating below a minimum threshold.
Options include:
• OK
• Major
• Minor
• Tx Input High
Indicates whether the Tx Input level is operating above a maximum threshold.
Options include:
• OK
• Major
• Minor

• Input Overdrive Protection

Indicates whether the internal Power Amplifiers are operating with overdrive.
Options include:
• OK
• Major
• Simulated Alarm
Indicates whether a simulated alarm has been issued. A simulated alarm is mainly
used for testing. Options include:
• OK
• Major
• Temperature (Internal)
Indicates that the internal temperature of the IBUC exceeds 85° C.
Note: If the High Temperature Shutdown alarm has been enabled and the internal
temperature of the IBUC exceeds 85° C, the IBUC will shut down automatically
• 10 MHz Source
Indicates whether the source of the 10 MHz reference signal is internal or external.
Note: For IBUCs operating with only an external 10 MHz reference signal, this field is
labelled “10 MHz Detector” and the options include:
• OK (indicates that the 10 MHz signal is functioning properly)
• Low (indicates that the 10 MHz signal is low or missing)
• PLDRO Lock
Indicates whether the phase-locked dielectric resonator oscillator (PLDRO)
frequency is locked (or stable). When the PLDRO is out-of-lock, this alarm causes
the muting of the amplifier and automatically shuts down the IBUC. Options
include:
• OK (indicates that the PLDRO is locked and functioning properly)
• Major
Note: This alarm is always a major alarm and is not available for user configuration.
• AGC Range
Indicates that the automatic gain control function is unable to maintain the gain
level. Options include:
• OK
• Major
This alarm occurs whenever the internal AGC gain is out of range and can no
longer maintain the desired Tx Output level
• N/A
• ALC Range
Indicates that the Tx Output level is being kept constant by the automatic level
control (ALC) function. Options include:
• OK
• Major
This alarm occurs whenever the internal ALC gain is out of range and can no
longer maintain the desired Tx Output level
• N/A
Note: Both ALC Range and ACG Range alarms are always a major and are not available
for user configuration.
Sensors
Use this tab to view real-time voltage, current, and power levels for the Cyber
Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC G.
Figure B.16 Sensor Tab

• Supply Voltage
Displays the supply voltage readings (V for DC-powered IBUCs; VAC for AC-
powered IBUCs). Valid values depend on the IBUC model. The readings on this
page should fall within the range listed on the Information on page B-7.
• Supply Current
Displays the current draw at the input of the IBUC in amps.
• Supply Power
Displays the power consumption of the IBUC (watts for DC-powered IBUCs; VA
for AC-powered IBUCs).

• Tx Input Level
Displays the Tx Input level in dBm.
• Tx Output Level
Displays the Tx Output level in dBm.
• Internal Temperature
Displays the real-time internal temperature of the IBUC in ° C.
Note: If the High Temperature Shutdown alarm has been enabled and the internal
temperature of the IBUC exceeds 85° C, the IBUC will shut down automatically.
• DRO Tuning Voltage
Displays the tuning voltage for the DRO in volts. This voltage is not static and is
continually monitored. The valid range is 1 to 9 volts; ideally, the DRO tuning
voltage should fall within the range of 2 to 8 volts when the DRO is locked.
If your readings consistently fall within the range of 1 to 2 volts or 8 to 9 volts,
contact Terrasat Technical Support.
Event Log
For extended monitoring and troubleshooting capabilities, the user is able to see all
events that occur within the Cyber Hardened unit by using the Event Log page. Each
Log page is able to show up to 25 event entries. The user is able to go to the next page
by pressing the Next button. The Clear button clears the entire event log.
Figure B.17 Event Log
Charts Menu
For extended monitoring periods, the user is able to view: Supply Current, Supply
Voltage, Input Power, Output Power and DRO Voltage Charts.
Figure B.18 Statistics Charts

SNMP Menu
Within the SNMP drop-down menu, the operator can access various SNMP Tabs used
to configure SNMP operation.
SNMP User Configuration

In this page, the operator is able to view existing SNMPv3 USM registered users (see
Figure B.19), add new SNMP users (Figure B.20) or delete existing users (Figure
B.21). A SNMPv3 user is composed of several fields:
• Username: String characters indicating the name that identifies the SNMP User.
This field can contain up to 32 characters.
• Privilege: Defines the security level that this user has access to. This field can
assume one of two values:
• auth (Read-Only Access)
• priv (Read-Write Access)
• Authentication Type: Can assume the value ‘SHA’.
• Authentication Key: String of alphanumeric characters indicating the pass phrase
used by the selected authentication method. This field can contain up to 32
characters.
• Encryption Type: Can assume the value ‘AES’.
• Encryption Key: String of alphanumeric characters indicating the pass phrase used
by the selected encryption method. This field can contain up to 32 characters.
• Group: String characters indicating the SNMP Group this user is mapped to. This
Figure B.19 SNMP Users
Figure B.20 SNMP User Add
Figure B.21 SMP User Delete
SNMP versions and Cyber Security envolved

Any of these management protocols, SNMP v1, v2 or v3, can be enabled or disabled.
Although different SNMP versions can also be supported, the default version is “v3
(USM)" for cyber security reasons.
Community strings or passwords such as "Read," "Write," and "Trap" or "public" and
"private" are only applicable for versions v1 and v2.
If you use SNMPv1 or SNMPv2, beware that although those strings are passwords,
they travel in clear text on the wire, which is considered unsafe. Since SNMPv3 is
encrypted, it is safer. Therefore, v3 is the default, the most secure, and most
recommended version for our Cyber Hardened IBUCs.
Note: If you need to use older SNMP versions such as v1 and v2, contact Terrasat's Tech
Support.
SNMP Views
In this page, the operator is able to view existing SNMPv3 views (see Figure B.22),
add new SNMP views (Figure B.23) or delete existing views (Figure B.24). A
SNMPv3 view is composed of several fields:

• Name: String characters indicating the name that identifies the MIB View. This
• Flag: Indicates whether the object described by the OID is included or excluded
from this view. Can assume one of two values, ‘included’ or ‘excluded’.
• OID Subtree: Object identifier string.
• Mask: Family mask used to define a family of view subtrees. It is composed of two
hexadecimal characters in length.
Figure B.22 SNMP Views
Figure B.23 SNMP Views Add
Figure B.24 SNMP Views Delete
SNMP Traps
In this page, the operator is able to manage and configure Trap communication. Trap
messaging requires several fields to be configured:
• Profile: String of up to 32 characters indicating the Notification Filter Profile

Name that will be used by Trap messages.
• Username: String of characters indicating the username of this Trap message. This

• Privilege: Defines the security level that this Trap message has access to. This field
can assume one of two values:
• auth
• priv
• Authentication Type: Can assume the value ‘SHA’.
• Authentication Key: String of alphanumeric characters indicating the pass phrase
used by the selected authentication method. This field can contain up to 32
characters.
• Encryption Type: Can assume the value ‘AES’.
• Encryption Key: String of alphanumeric characters indicating the pass phrase used
by the selected encryption method. This field can contain up to 32 characters.
• Trap Destination IP Address: IP address indicating the destination IP of this Trap
message.
Figure B.25 SNMP Trap Sessions
Figure B.26 SNMP Trap Session Add
SNMP Trap Notifications Filters

In this page, the operator is able to manage and configure Trap Notification Filters
used by the unit. The notification filter enables the Cyber Hardened unit to choose
which type of SNMP notifications are sent to the management station based on the
OID of the notification to be sent.
• Profile: String of characters indicating the name that identifies the Filter profile.
This field can contain up to 32 characters.
Note: This field will be used when configuring SNMP Traps
• OID Subtree: Object identifier string.
• Flag: Indicates whether the object described by the OID is included or excluded
from this filter. Can assume one of two values, ‘included’ or ‘excluded’.
• Mask: Family mask used to define a family of view subtrees. It is composed of two
Figure B.27 SNMP Notifications & Filter
Figure B.28 Adding Notifications & Filters

SNMP Groups
In SNMP Group page, the user is able to view existing groups (Figure B.29), add new
groups (Figure B.30) and delete existing groups (Figure B.31) from the unit.
• Group Name: String of characters indicating the name that identifies the SNMP
Group. This field can contain up to 32 characters.
• Privilege: Defines the security level that this group has. This field can assume one
of three values:
• auth
• priv
• Read View: String of up to 32 characters indicating the read access to management
objects for the group.
• Write View: String of up to 32 characters indicating the write access to
management objects for the group.
• Notify View: String of up to 32 characters indicating the read access to
management objects for the group.
Note: All three Read, Write and Notify Views can contain key values, such as none or
all, indicating that the group has access to none of the management objects or all of
them. In addition, the user is also able to input a specific view that the group will
have.
Note: A couple of default groups are available to the operator. Auth Group
Figure B.29 SNMP Groups
Figure B.30 Add SNMP Groups
Figure B.31 Delete SNMP Groups

C
A PPENDIXC
ASCII COMMAND/RESPONSE STRUCTURE

CHAPTER0
Cyber Hardened IBUC Console and SSHv2 Command Set
This command set is appropriate for RS232 and SSHv2 interfaces.

• Parameters are delimited by “< >” for clarity and are not part of the actual query or
command. Single quotes delimit an exact string used for a parameter.
• It is expected that both, commands and responses are terminated by using
<LF><CR>, where;
<LF> = 0x0A. (Line Feed)

<CR>= 0x0D. (Carriage Return)
Be sure to configure the SSHv2 or RS232 client accordingly.
In some cases, users may type queries/commands with structures that differ from the
software’s expected parameters. In these cases, one should receive an “Error
Response” from the IBUC unit. Refer to Table C.1 for a more detailed explanation
about such error messages.
Table C.1 Error Response Table
Code Error Message Description

This is not a valid value, entry, or syntax for
1 error = invalid value
this command.
2 error = bad command This command is not in the command set.
3 error = func not yet done This command has not been implemented.
One of the parameters is formatted
4 error = bad format in command
incorrectly.
5 error = error accessing config storage Unable to access EEPROM.
6 error = ODU fault Cannot switch, target unit has a major fault.
7 error = Please enter valid password Incorrect password has been entered.
8 error = Switch Fault The waveguide switch is faulted.
Table C.1 Error Response Table (Continued)
Code Error Message Description

9 error = ODU Comm Fault Legacy Binary packet checksum is invalid.
UDP has timed out waiting for response
10 error = Timeout waiting for packet
packet.
The slave cannot perform the requested
11 error = Not master
command.
Cannot engage AGC/ALC because Tx
12 error = Turn on Tx first
Output is muted.
Cannot engage AGC/ALC because DRO is
13 error = Tx Alarms present
out of lock.
AGC/ALC time out waiting for a valid burst
14 error = Burst Not Detected
(15 seconds).
The ALC target power is outside the valid
15 error = AGC/ALC Targets OOR power range of the unit. The AGC target gain
is outside the range of the unit.
When engaging AGC/ALC mode, the gain
16 error = Gain Control OOR
control is outside preset limits.
17 error = Redund not enabled This unit is not part of a redundant pair.
The IP subnet selected is invalid for the
18 error = Invalid IP for subnet
configured IP address.
19 SET is not valid with <command> You can only query this parameter.
20 GET is not valid with <command> You can only change this parameter.
C-2 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: ASCII Command/Response Structure
ADU
Description: Displays or adds IBUC users.

• The user type “user” is meant for read-only access. Such users can read values but
cannot set them.
• The user type “admin” can set values to passwords and add new users.
Query: ADU
Q
Response Values: <Username>, <User Type>
Command: ADU = <Username>,<Password>,<UserType>

C
Response: “chpasswd: password for ‘<Username>’ changed”
Parameters:
<Username>
string of displayable ASCII characters [up to 32 characters]
(Create a new username based on your demand).
<Password>
string of displayable ASCII characters [up to 32 characters]
(Create a new temporary password for the new username).
<User Type>
‘admin’ or ‘user’
(Define the settings attributed to each new user).
Note: Once the users are created, their usernames cannot be changed.
You may delete an user and create another one with a different username using the
command DLU on page C-25.
Cyber Hardened IBUC Console and SSHv2 Command Set | C-3

Example:
After logging in, here the user will find an example of how to use the command
prompt to;
• View the current list of users.
• Add a new user called ‘admin2’, with a temporary password set using the same
characters, ‘admin2’, and set it for Admin properties.
• Add a new user called ‘username3’with a temporary password set using the same
characters, ‘username3’, and set it for User properties.
(Example user: xxxx / Example IP adress: 10.10.12.33)
Figure C.1 Login as ‘xxxx’ (Admin user) showing ADU Query and Command execution.
ATL
Description: Displays the minimum and maximum internal temperatures in degrees C

recorded since leaving the factory.
Query: ATL
Q
Response Values: <±aaa>, <±bbb>, <nnnnn>
Parameters:
<±aaa>
Minimum temperature in degrees C. This parameter can assume positive or
negative values
<±bbb>
Maximum temperature in degrees C. This parameter can assume positive or
negative values
<nnnnn>
Number of writes to temp. log
C10
Description: Displays the current state of the external 10 MHz source. When no
external 10 MHz source is configured the <State> parameter will always be read as
‘1=10MHz within Range’.
Query: C10
Q
Response: <State>
Parameters:
<State>
1 = 10MHz within Range / 0 = 10MHz out of range

CAS
Description: Displays the current active alarms. Use the CAS command to display
hexadecimal values that represent the Transmit and Miscellaneous alarms. For the
meaning of the individual alarms or to use CAS=1 to display the alarm strings, see
Table C.2.
Query: CAS
Q
Response: CAS=T0xhhhh,M0xhhhh
Query: CAS=1
Q
Response:
Verbose alarm report
Tx alarms: 0xhhhh
<Tx alarm strings>
Misc alarms: 0xhhhh
<misc alarm strings>
Parameter:
<Tx alarm strings>
verbose strings of each alarm that is active.
<misc alarm strings>
verbose strings of each alarm that is active.
Table C.2 Alarm Mask
Transmit Alarm Mask Transmit Alarm Mask

0x0001 AGC/ALC Out of Range Alarm 0x0100 Tx Simulated Alarm
0x0002 Tx Muted Alarm 0x0200 10 MHz Reference Alarm
0x0004 DRO Loss of Lock Alarm 0x0400 Not Used
0x0008 Tx Output Threshold High Alarm * 0x0800 Not Used
0x0010 Tx Output Threshold Low Alarm * 0x1000 Input Overdrive Alarm
0x0020 Tx Input Threshold High Alarm * 0x2000 Not Used
AGC/ALC Target Out of Range
0x0040 Tx Input Threshold Low Alarm * 0x4000
Alarm
0x0080 High Temperature Alarm * 0x8000 Not Used
CBT
Description: Displays or configures the longest allowable time between valid data
bursts before the IBUC reports an alarm. This command applies when the IBUC is set
to burst power monitoring.
Query: CBT
Q
Response: CBT=<Timeout>
Command: CBT=<Timeout>
C
Response: CBT=<Timeout>
Parameters:
<Timeout>
Timeout value in seconds [0 to 300]. A value of 0 means no timeout.
CCF
Description: Display the power offset between the RF output and the sample port.
CCF is not available unless the IBUC has a sample port. This query returnfs the offset
for the frequency configured with TFR.
Query: CCF
Q
Response: CCF=<Offset>
Parameter:
<Offset>
Offset between the RF output and the sample port [decimal number in dB]

CCM
Description: Displays the model number and serial number of the Cyber Hardened
IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G.
Query: CCM
Q
Response Values: CCM=<Model Number>,<Serial Number>
Parameters:
<Model number>
Model number variable string [up to 20 characters]
<Serial Number>
Serial number variable string [up to 10 characters]
CCS
Description: Displays the M&C firmware version level / last revision / last update,
with date and time. This is a read-only command.
Query: CCS
Q
Response: CCS=FW IBB v<mm>.<nn>, <date> <time>
Parameters:
<mm>
Major revision number [0 to 99]
<nn>
Minor revision number [0 to 99]
CFD
Description: Displays the total amount of operating hours for the unit. For this
feature, time accumulates even over reboots.
Query: CFD
Q
Response: CFD=TOTAL HRS=<time>
Parameters:
<time>
Total amount of hours in full numbers [0 to 999999].
Response Example: CFD=TOTAL HRS=148
CIA
Description: Displays or sets the IP address of the unit. Valid values range from (but
do not include) 1.0.0.0 through 223.255.255.254.
Query: CIA
Q
Response: CIA=<IP Address>
Command: CIA=<IP Address>

C
Response: CIA=<IP Address>
Parameters:
<IP Address>
IP address of the unit [1.0.0.0 to 223.255.255.254]
Note: Typical usage of this command to set up network is,

IBUC>CIA=192.168.1.200
IBUC>CIM=255.255.255.0
IBUC>CIG=192.168.1.1
For CIM and CIG commands descriptions, see CIHA on page C-12 and CIG on
page C-12.
CIC
Description: The CIC command sets the SNMP “community strings” if the SNMP
version is configured and operating in versions v1 or v2 (which is not recommended as
specified in SNMP versions and Cyber Security envolved on page B-29).
Query: CIC
Q
Response: CIC=<SNMP is set to v3. Community string are applicable for
v1/2>
Command: CIC=<public_community_string, private_community_string,

C
trap_community_string>
Parameters:
<public_community_string>
Public community string – The password for reading an SNMP variable.
<private_community_string>
Private community string – The password for setting a variable.
<trap_community_string>
Trap community string – The password for issuing traps.
Note: This command (CIC) only works for SNMP versions v1 and v2. SNMPv3 does not
require this command.
Note: The SNMP community strings are means of accessing data stored within our devices.
Since they work like passwords, one cannot read an already set SNMP string right on
the monitor. It is Purposefully hidden.
CID
Description: Displays the current consumption by the IBUC.
Query: CID
Q
Response:
AC Current=<Value> Amps
or
DC Current=<Value> Amps
Parameter:
<Value>
Current consumption [decimal number]
CIE
Description: Displays or sets SSH and web server access. By default, SSH and Web
server are enabled. You may use this command to enable or disable them. Serial port
access is always available and cannot be disabled since it would make the Cyber
Hardened unit inaccessible.
Query: CIE
Q
Response: CIE=<ssh=1, web=1>
Command: CIE=<network access>, <binary 0 or 1>

C CIE=<ssh,0/1> or CIE=<web,0/1>
Response: CIE=Nothing if there is no problem, and usage otherwise.
Parameters:

<network access>
ssh - SSH (Secure Shell) Server access.
web - Web Server access.
<binary 0 or 1>
0 - Disables
1 - Enables
Note: In these systems, data security is more emphasized on internet abuse than physical
abuse.
CIG
Description: Displays or configures the IBUC network gateway address. This address
will be sent to if the requested IP address does not reside on the local LAN segment.
Query: CIG
Q
Response: CIG=<Gateway IP>
Command: CIG=<Gateway IP>

C
Response: CIG=<Gateway IP>
Parameter:
<Gateway IP>
Network Gateway Address [1.0.0.0 to 223.255.255.254]
CIHA
Description: Displays, enables, adds or configures the IBUC Trap Host.
This code only applies to the SNMP versions v1 and v2. For SNMPv3, use the
command STA on page C-36.
Query: CIHA
Q
Response: CIHA=<Gateway IP 1>
_______________<Gateway IP 2>
Command: CIHA=<Gateway IP>

C
Response: If you receive no answer, there is no problem. If there is
something wrong, you will receive an usage error message.
Parameter:
<Gateway IP>
Network Gateway or IP Address to be added [1.0.0.0 to 223.255.255.254]
CIHD
Description: This code disables and deletes a Trap IP Address or a Gateway IP.
This code only applies to the SNMP versions v1 and v2. For SNMPv3, use the
command STD on page C-37.
Command: CIHD=<Gateway IP>

C
Response: If you receive no answer, there is no problem. If there is
something wrong, you will receive an usage error message.
Parameter:
<Gateway IP>
Network Gateway Address to be deleted [1.0.0.0 to 223.255.255.254]

CIM
Description: Displays or sets the Network Mask.
Query: CIM
Q
Response: CIM=<Netmask>
Command: CIM=<Netmask>
C
Response: CIM=<Netmask>
Parameter:
<Netmask>
Network Mask [255.0.0.0 to 255.255.255.252]
CIS
Description: Displays the current SNMP version and allows switching between
SNMP versions, enabling or disabling particular versions.
Note: Keep in mind the SNMPv3 is the standard and recommended version for Cyber
Security.
Query: CIS
Q
Response: CIS=<State/Version>
Command: CIS=<State/Version>
C
Response: You will get no response if there is no problem. On the other
hand, if there is something wrong, you may get a usage error message.
Parameters:
<State/Version>
0 - Disables SNMP.
1 - Enables the SNMP version v1
Note: The most common usage error messages are due to invalid entry values. Please
check if your syntax writing is accurate. If the problem persists, check the error
message and consult our Error Response Table on page C-1.
CLE
Description: Displays or sets the state of the external LED indicator. If disabled, the
external LED indicator will remain off.
Query: CLE
Q
Response: CLE=<State>
Command: CLE=<State>
C
Response: CLE=<State>
Parameters:
<State>
0 - Off / 1 - On

CM1
Description: Displays or sets the minor alarm mask of the unit. This is a hexadecimal
value. See Table C.3 for available hexadecimal values.
Query: CM1
Q
Response: CM1=<Hex Mask>
Command: CM1=<Hex Mask>

C
Example: CM1=0x0008 will set the Tx Output Threshold High Alarm to
minor.
Parameter:
<Hex Mask>
Minor alarm mask [Hexadecimal value.
Table C.3 below refers to configurable alarm mask values. Only the alarms shown
in the table are maskable out of all alarms available.
Table C.3 Configurable Alarm Mask
Transmit Alarm Mask

0x0008 Tx Output Threshold High Alarm
0x0010 Tx Output Threshold Low Alarm
0x0020 Tx Input Threshold High Alarm
0x0040 Tx Input Threshold Low Alarm
0x0080 High Temperature Alarm
CM2
Description: Displays or sets the major alarm mask of the unit. This is a hexadecimal
value.
Query: CM2
Q
Command: CM2=<Hex Mask>

C
Example: CM2=0x0008 will set the Tx Output Threshold High Alarm to
major.
Parameter:
<Hex Mask>
Major alarm mask [Hexadecimal value]
See Table C.3 on page C-16 for available hexadecimal values.

CMS
Description: Display or configure the alarm suppression mask. This command does
not suppress alarms. You must set TAZ=1 to enable suppression.
Query: CMS
Q
Response: CMS=<Hex Mask>
Command: CMS=<Hex Mask>

C
Example: CMS=0x0008 will set the Tx Output Threshold High Alarm to
suppressible.
Response: CMS=<Hex Mask>
Parameter:
<Hex Mask>
Alarm suppression mask [Hexadecimal value]
See Table C.3 on page C-16 for available hexadecimal values.
Note: To suppress alarms,

IBUC> CMS=<Hex Mask>
IBUC> TAZ=1
COI
Description: Displays general information about the IBUC. This is a read-only

command.
Query: COI
Q
Response:
COI=Undefined
Model Undefined,
SN TE8100000,
FW IBB v1.0, Jun 24 2020 10:10:17,
P=0(0 W)
LOid=3:CS, (5850 to 6425 MHz)
Query: COI=1
Q
Response:
COI=ODUPwr(CSM)=30.0 dBm, TxOn/Off=0
Band=CS
PwrClass=0(0 W)
PLDRO ool=1, Temp. Out of Range=0
FW IBR v1.0, Jun 24 2020 10:10:17
BucSn=TE8100000, HwAssyRev=Undefined
HousingTemp=-12, HighTempSdEn=1

COX
Description: Displays the current internal temperature of the unit.
Query: COX
Q
Response: COX=<Internal Temperature>
Query: COX=1
Q
Response: COX=<External Temperature>
Parameter:
<Internal Temperature>
Current internal temperature of the unit [degrees C]. Parameter can assume
negative or positive values
<External Temperature>
Current external temperature of the unit [degrees C]. Parameter can assume
negative or positive values
CPL
Description: Displays the private label string of the unit.
Query: CPL
Q
Response: <Manufacturer>
Parameter:
<Manufacturer>
String representing the manufacturer of the IBUC [String]
CPS
Description: Sets or changes the password for the current user who is logged in. To
change passwords for other users, use the “ADU” command on page C-3. The
password does not take effect until the next login. You cannot query this item.
Command: CPS=<New Password>

C
Response: TBD
Parameter:
<New Password>
New password for current user [String]
CRT
Description: Displays or configures the internal 10 MHz source frequency.

• Whenever the IBUC is mounted, operational, or equipped, and has the internal 10
MHz source on, an operator may trim or adjust the frequency output of the IBUC.
• The incremental frequency movement at the output of the IBUC will vary
depending on the band frequency.
Query: CRT
Q
Response: CRT=<Value>
Command: CRT=<Value>
C
Response: CRT=<Value>
Parameters:
<Value>
Internal 10 MHz source trim value [0 to 4095]

CSF
Description: Displays or configures the IBUC for an input AC frequency of 50/60 Hz.
This command only applies to AC powered IBUCs.
Query: CSF
Q
Response: CSF=<AC Frequency>
Command: CSF=<AC Frequency>

C
Response: CSF=<AC Frequency>
Parameters:
<AC Frequency>
0 = 60 Hz / 1 = 50 Hz
CTI
Description: Displays internal 10 MHz source installed.
Query: CTI
Q
Response: CTI=<Value>
Parameters:
<Value>
0 = Not Installed / 1 = Installed
CTM
Description: Displays or configures the IBUC real time clock. If NTP is not used this
provides a way of manually setting the system clock. The IBUC will maintain time up
to a week during power losses. It is preferable to use NTP to avoid having to reset the
system time.
Query: CTM
Q
Response: CTM=<Date> <Time>
Command: CTM=<Date> <Time>

C
Response: CTM=<Date> <Time>
Parameters:
<Date>
Date used by IBUC unit [mm/dd/yyyy] (e.g.: 07/02/2020)
<Time>
Time used by IBUC unit [hh:mm:ss] (e.g.: 15:40:27)
CTV
Description: Displays the DRO tuning voltage. This is a read-only command.
Query: CTV
Q
Response: DRO Voltage=<Tuning Voltage> Volts
Parameters:
<Tuning Voltage>
DRO tuning voltage [decimal number from 0 to 10.00]

CVD
Description: This command displays the current input AC/DC power.
Query: CVD
Q
Responses:
AC Voltage=<AC Reading> Volts
or
DC Voltage=<DC Reading> Volts
Parameters:
<AC Reading>
Current AC input voltage [decimal number with one decimal place]
<DC Reading>
Current DC input voltage [decimal number with one decimal place]
CZZ
Description: Reboots the IBUC and/or resets all parameters to their default values. .
Command: CZZ
C
Response: None
Command: CZZ=1
C
Response: None
Note: Issuing the command CZZ=1 will prompt the IBUC to reset all internal parameters to
their default and then reboot the IBUC. Both commands will cause a momentary mute
of the transmitter, and should be used with caution.
DLU
Description: This command allows an administrator to delete another user from the
system.
Command: DLU=<Username>
C
Response: No response is given.
Parameter:
<Username>
User that will be deleted [String]
DRO
Description: Get min/max DRO tuning volts. This command displays the maximum
and minimum DRO tuning voltage recorded by the IBUC.
Query: DRO
Q
Response: DRO: min=<Min Value>, max=<Max Value>, origin<Original
Value>
Parameters:
<Min Value>
Minimum voltage recorded by th IBUC [0 to 10.0 volts]
<Max Value>
Maximum voltage recorded by th IBUC [0 to 10.0 volts]
<Origin Value>
DRO voltage when the IBUC left the factory [0 to 10.0 volts]

DTM
Description: Disables the internal 10 MHz. This command allows the user to disable
the internal 10 MHz source for troubleshooting purposes. This command does not
persist through a reboot of the IBUC.
Query: DTM
Q
Response: DTM=<State>
Command: DTM=<State>
C
Response: DTM=<State>
Parameters:
<State>
0 = normal operation / 1 = disable internal 10 MHz source
EHI
Description: Displays up to 25 IBUC event history entries. Each subsequent call

displays up to 25 more entries. Once the history end is reached the ‘No New Events’
string will appear. Issuing the command EHI=0 will reset the index of the event log,
allowing the user to see the log from beginning.
Query: EHI
Q
Response: <Date> <Time> <Event String>
Command: EHI=0
C
Response: <Date> <Time> <Event String>
Parameters:
<Date>
Date in which the event was issued [mm/dd/yyyy]
<Time>
Time in which the event was issued [hh:mm:ss]
<Event String>
String that corresponds to the issued command [String]
EHZ
Description: Clears the event history of the IBUC.
Command: EHZ
C
Response: “event log cleared”
Parameters:
<Status>
It shows a message reporting that the event history has been cleared.

HLP
Description: Displays the available list of commands, showing the three letters for the
command or query and a brief description of functions or properties.
Query: HLP
Q
Response: <xxx> - <xxxxxx xxxx xxxxxxxxxxx>
Parameters:
<xxx>
Command’s sequence of three letters.
<xxxxxx xxxx xxxxxxxxxxx>
Command’s brief description of functions or properties.
ISSUE
Description: Displays, adds or configures a misuse message.

This command allows you to edit and control a Terminal and Web interface that shows
a message to warn intruders about legal action in misuse cases of the system.
• This code is a command only. To view
• Login out of the unit will show the message.
Command: ISSUE=<xxxxxx xxx xxxxx xxxxx>

C
Response: No response is shown for this command.
Parameters:
<xxxxxx xxx xxxxx xxxxx>
Fill this space with a text message you wish to display to any potential intruder,
who might misuse the system.
Note: Nothing is shown on the screen right after typing the command and pressing the“Enter
key,” “Carriage Return.” Instead, it opens a blank line for you to fill with your
massage. This code offers you a text editor space: Start typing the message and press
CTRL+D to save it when you finish.
Note: Log out to see the message. You may use the shortcut: CTRL + C on page C-55.
NTP
Description: Displays, adds or configures the NTP Server IP addresses. This code can
add up to 2 NTP servers to the list.
Query: NTP
Q
Response: <IP/Hostname 1>
<IP/Hostname 2>
Command: NTP=<IP/Hostname>
C
Response:
<IP/Hostname>
Parameters:
<IP/Hostname>
NTP Server IP address or Hostname
NTPDEL
Description: This command deletes a specific NTP server from a pool of NTP servers.
Command: NTPDEL=<IP/Hostname>
C
Response: You will get no response if there is no problem. On the other
hand, if there is something wrong, you may get a usage error message.
Parameters:

<IP/Hostname>
Insert the NTP Server, IP address, or Hostname to be deleted.
SGA
Description: Displays or configures the security to group mapping of SNMPv3.

Query: SGA
Q
Response:
<Group Name>,<Level>,<Readview>,<Writeview>,<Notifyview>
Command: SGA=
C <Group Name>,<Level>,<Readview>,<Writeview>,<Notifyview>
Response:
<Group Name>,<Level>,<Readview>,<Writeview>,<Notifyview>
Parameters:
<Group Name>
SNMPv3 group name [up to 32 alpha numeric characters]
<Level>
SNMPv3 group matching security level [up to 32 alphanumeric characters]
<Readview>
SNMPv3 group read view [up to 32 alphanumeric characters]
<Writeview>
SNMPv3 group write view [up to 32 alphanumeric characters]
<Notifyview>
SNMPv3 group notify view [up to 32 alphanumeric characters]
SGD
Description: Deletes an existing SNMPv3 group.

Command: SGD=<Group Name>,<Level>
C
Response:
Parameters:
<Group Name>
SNMPv3 group name that should be deleted [alphanumeric string]
<Level>
SNMPv3 group matching level [up to 32 alphanumeric characters]
SHL
Description: Displays up to 25 IBUC statistic history entries. Each subsequent call

displays up to 25 more entries. Once the history end is reached, the ‘No New Stats’
string will appear. Issuing the command SHL=0 will reset the statistics log index to the
beginning.
Query: SHL
Q
Response: <Date> <Time> <POut> <PIn> <Temp> <DRO> <Volt>
<Amp>
Command: SHL=0
C
Response: <Date> <Time> <POut> <PIn> <Temp> <DRO> <Volt>
<Amp>
Parameters:
<Date>
Date of the statistic entry [mm/dd/yyyy]
<Time>
Time that the statistic entry was issued [hh:mm:ss]
<POut>
IBUC output RF power [decimal number]
<PIn>
IBUC input IF power [decimal number]
<Temp>
Internal temperature of the IBUC in degrees C [integer]
<DRO>
DRO tuning voltage [decimal number]
<Volt>
DC/AC power input voltage [decimal number]

<Amp>
DC/AC power input current [decimal number]
SHP
Description: Displays or configures the data collection period for statistics.
Query: SHP
Q
Response: SHP=<Period>
Command: SHP=<Period>
C
Response: SHP=<Period>
Parameters:
<Period>
Period of data collection [1 to 1440 minutes] If Period is selected to be 0 statistic
collection will be disabled.
SHZ
Description: Clears the statistics history/log of the IBUC.
Command: SHZ
C
Response: stat log cleared
Parameters:
<Status>
It shows a message reporting that the status for the statistics history has been
cleared.
Note: Once the history is deleted it cannot be retrieved again.
Once the statistics log is cleared, the system automatically continues collecting data
afresh. No further action is required to restart the data collection.

SNA
Description: Displays the existing SNMPv3 Trap Notification Filter or adds a new
one. For user configuration, use one or more of the parameters below.
You may see no response on the output of your first attempt to query this code. It may
happen because there is no target or notification filter for SNMP by default. Therefore,
the operator has to add one. To do so, the user should;
• use first the command STA on page C-36
• and after that, use the Command SNA, to add a proper “Profile”, Subtree”, and a
“Mask”, as described below.
Query: SNA
Q
Response: <Profile>,<Subtree>,<Type>,<Mask>
Command: SNA= <Profile>,<Subtree>,<Type>,<Mask>

C
Response: <Profile>,<Subtree>,<Type>,<Mask>
Parameters:
<Profile>
String of up to 32 characters indicating the Notification Filter Profile Name that
will be used by Trap messages.
Example: “ColdBoot” or “WarmBoot”.
<Subtree>
OID tree to filter.
Example: “.1.5.2.4.1.31248.1”.
<Type>
Inclusion or Exclusion status desired.
Example: “Included” or “Excluded”.
<Mask>
Family mask used to define a family of view subtrees. It is composed of two
Example: “0x00”.
SND
Description: Deletes an existing SNMPv3 Trap Notification Filter.
Command: SND= <Profile>,<Subtree>

C
Response: <Profile>,<Subtree>
Parameters:
<Profile>
will be used by Trap messages
<Subtree>
OID tree to filter.

STA
Description: Displays the existing SNMPv3 Trap sessions or adds new SNMPv3
Traps. Use one or more of the parameters below for user configuration.
Note: This code is not supported on SNMP versions v1 and v2.
Query: STA
Q
Response: <Profile>,<Username>,<Privilege>,<Authentication>,<Auth.
Password>, <Encryption>,<Priv. Password>,<Target IP>
Command: STA= <Profile>,<Username>,<Privilege>,<Authentication>,

C <Auth. Password>, <Encryption>,<Priv. Password>,<Target IP>
Response: <Profile>,<Username>,<Privilege>,<Authentication>, <Auth.

Password>, <Encryption>,<Priv. Password>,<Target IP>
Parameters:
<Profile>
will be used by Trap messages.
<Name>
String of characters indicating the username of this Trap message. This field can
contain up to 32 characters.
<Privilege>
Defines the security level that this Trap message has access to. This field can
assume one of two values:
• auth
• priv
<Authentication>
Can assume the value, ‘SHA’.
<Authentication Password>
String of alphanumeric characters indicating the pass phrase used by the selected
authentication method. This field can contain up to 32 characters.
<Encryption>
Can assume the value ‘AES’.
<Encryption Password>
String of alphanumeric characters indicating the pass phrase used by the selected
encryption method. This field can contain up to 32 characters.
<Target IP>
IP address indicating the destination IP of this Trap message.
STD
Description: Deletes an SNMPv3 Trap session. Use one or more of the parameters
below for user configuration.
Command: STD= <Profile>,<Name>,<Target IP>

C
Response: <Profile>,<Name>,<Target IP>
Parameters:
<Profile>
will be used by Trap messages
<Name>
String of characters indicating the username of this Trap message. This field can
contain up to 32 characters.
<Target IP>
IP address indicating the destination IP of this Trap message.

SUA
Description: Displays or configures an SNMPv3 user. Use one or more of the

parameters below for user configuration.
Query: SUA
Q
Response: <Name>,<Privilege>,<Authentication>,<Auth. Password>,
<Encryption>,<Priv. Password>,<Group>
Command: SUA= <Name>,<Privilege>,<Authentication>,

C <Auth. Password>,<Encryption>,<Priv. Password>,<Group>
Response:<Name>,<Privilege>,<Authentication>,<Auth. Password>,
<Encryption>,<Priv. Password>,<Group>
Parameters:
<Name>
Username [up to 32 alphanumeric characters]
<Privilege>
User privilege [‘rouser’ or ‘rwuser’]
<Authentication>
Authentication method [‘SHA’]
<Password>
User authentication password [min of 8; max of 32 alphanumeric characters]
<Encryption>
Encryption method [‘AES’]
<Priv. Password>
Encryption password [min of 8; max of 32 alphanumeric characters]
<Group>
Group name configured with SGA.
Note: Two users, ‘auth_no_priv’ and ‘auth_priv’ are preconfigured for read-only and read-
write access. The following MIB are available by default:
• SNMPv2-MIB
• HOST-RESOURCES-MIB
• TERRASAT-MIB
• TERRASAT-SMI-MIB
• SNMP-FRAMEWORK-MIB
• SNMP-MPD-MIB
• SNMP-USER-BASED-SM-MIB
• SNMP-VIEW-BASED-ACM-MIB
• SNMP-TARGET-MIB
• SNMP-NOTIFICATION-MIB
SUD
Description: Deletes an SNMPv3 user.
Command: SUD=<User>
C
Response: User successfully deleted
Parameter:
<User>
Username of a previously configured user that should be deleted [String]

SVA
Description: Displays or configures an SNMPv3 view.
Query: SVA
Q
Response: <Name>,<Flag>,<OID Tree>,<Mask>
Command: SVA=<Name>,<Flag>,<OID>,<Mask>
C
Response:<Name>,<Flag>,<OID>,<Mask>
Parameters:
<Name>
SNMPv3 view name [up to 32 alphanumeric characters]
<Flag>
SNMPv3 flag [‘included’ or ‘excluded’]
<OID>
SNMPv3 OID
<Mask>
Mask indicating which OIDs must match to be part of the view [Hex value]
SVD
Description: Deletes a view from an SNMPv3.
Command: SVD=<View Name>,<OID Tree>

C
Response: View <View Name> deleted
Parameter:
<View Name>
SNMPv3 view representing name [up to 32 alphanumeric characters]
<OID Tree>
SNMPv3 view matching OID [integer]
TAH
Description: Displays or sets the output high power threshold based upon the Cyber
Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G Rated Power Level
(RPL). See Table C.4 on page C-45. This item must be greater than the TAL setting.
Query: TAH
Q
Response: TAH=<Value>
Command: TAH=<Value>
C
Response: TAH=<Value>
Parameters:
<Value>
Output high power threshold [RPL – 20 dB to RPL + 1 dB

TAL
Description: Displays or sets the output low power threshold based upon the Cyber
Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G Rated Power Level
(RPL). See Table C.4 on page C-45. This setting must be less than the TAH setting.
Query: TAL
Q
Response: TAL=<Value>
Command: TAL=<Value>
C
Response: TAL=<Value>
Parameters:
<Value>
Output low power threshold [RPL – 20 dB to RPL + 1 dB]
TAS
Description: Displays or sets the Tx simulated alarm setting.
Query: TAS
Q
Response: TAS=<Setting>
Command: TAS=<Setting>
C
Response: TAS=<Setting>
Parameter:
<Setting>
0 = no alarm, 1 = alarm
TAZ
Description: Enables the suppression of any alarms configured as suppressible.
Query: TAZ
Q
Response: TAZ=<Setting>
Command: TAZ=<Setting>
C
Response: TAZ=<Setting>
Parameter:
<Setting>
0 = no suppression / 1 = suppress configured alarms
TBH
Description: Display or configure the input power high alarm threshold. This setting
must be greater than the TBL setting.
Query: TBH
Q
Response: TBH=<Value>
Command: TBH=<Value>
C
Response: TBH=<Value>
Parameters:
<Value>
Input power high alarm threshold [-60 dBm to -15 dBm]

TBL
Description: Displays or configures the input low power alarm threshold. This setting
must be less than the TBH setting.
Query: TBL
Q
Response: TBL=<Value>
Command: TBL=<Value>
C
Response: TBL=<Value>
Parameters:
<Value>
Input power low alarm threshold [-60 dBm to -15 dBm]
TBT
Description: Displays or sets the burst threshold based upon the Cyber Hardened
IBUC 2, IBUC 2e, IBUC 2G, IBUC R, or IBUC G Rated Power Level (RPL). See
Table C.4. This command only applies if the IBUC is configured for burst power
monitoring.
Query: TBT
Q
Response: TBT=<dBm>
Command: TBT=<dBm>
C
Response: TBT=<dBm>
Parameters:
<dBm>
Burst threshold [RPL – 20 dB to RPL + 1 dB]
Table C.4 Default Values for the TAH, TAL, and TBT Commands
Power Level TAH TAL TBT

Watts dBm Default Value Default Value Default Value
002 33.0 34.0 13.0 13.0

004 36.0 37.0 16.0 16.0
005 37.0 38.0 17.0 17.0
008 39.0 40.0 19.0 19.0
010 40.0 41.0 20.0 20.0
012 40.8 41.8 21.0 21.0
016 42.0 43.0 22.0 22.0
020 43.0 44.0 23.0 23.0
025 44.0 45.0 24.0 24.0
030 44.8 45.8 25.0 25.0
040 46.0 47.0 26.0 26.0
050 47.0 48.0 27.0 27.0
060 47.8 48.8 28.0 28.0
080 49.0 50.0 29.0 29.0
100 50.0 51.0 30.0 30.0
125 51.0 52.0 31.0 31.0
150 51.8 52.8 32.0 32.0
175 52.4 53.4 32.4 32.4
200 53.0 54.0 33.0 33.0
400 56.0 57.0 36.0 36.0
TDT
Description: Displays the input L-band Power Level for the Tx (Transmission
System) in dBm.
Query: TDT
Q
Response: Tx Input Power=<Level> dBm
Parameter:
<Level>
L-Band input power level [decimal number]

TFB
Description: Displays the RF frequency band of this Cyber Hardened IBUC 2,

IBUC 2e, IBUC 2G, IBUC R or IBUC G. See Table C.5 for more information about
band numbers and corresponding frequency range.
Query: TFB
Q
Response: TFB=<Band Number> dBm
Parameter:
<Band Number>
Corresponding band numbering [Integer]
Table C.5 Band Numbering
Band Number Band Name Frequency

03 Standard C-band 05850 - 06425 MHz
04 Insat C-band 06725 - 07025 MHz
05 Extended Ku-band 13750 - 14250 MHz
06 Standard Ku-band 14000 - 14500 MHz
07 X-band 07900 - 08400 MHz
08 Full Ku-band 13750 - 14500 MHz
09 Extended C-band 05850 - 06650 MHz
10 Full C-band 05850 - 06725 MHz
11 Low Ku-band 12750 - 13250 MHz
12 Palapa C-band 06425 - 06725 MHz
14 DBS-band 1 17300 - 18100 MHz
15 DBS-band 2 18100 - 18400 MHz
16 Ka-band 1 29500 - 30000 MHz
17 Ka-band 2 30000 - 31000 MHz
18 Ku-band 4 12800 - 13300 MHz
19 C-band 6 05725 - 06425 MHz
20 Ka-band 3 29000 - 30000 MHz
21 Ka-band 4 30500 - 31000 MHz
22 GlobalStar C-band 05000 - 05200 MHz
TFI
Description: Displays the spectral inversion for this Cyber Hardened IBUC 2,
IBUC 2e, IBUC 2G, IBUC R or IBUC G. This is a read-only command.
Query: TFI
Q
Response: TFI=<Value>
Parameter:
<Value>
0 = Non-inverted (low side LO) / 1 = Inverted (high side LO)
TFR
Description: Displays or sets the output power monitor frequency of the Cyber
Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G. The default values in
Table C.6 on page C-48 are listed according to the model number of the Cyber
Hardened IBUC. The command only increases the accuracy of the displayed power
levels.
Query: TFR
Q
Response: TFR=<Frequency>
Command: TFR=<Frequency>
C
Response: TFR=<Frequency>
Parameter:
<Frequency>
Which IF or RF frequency (in MHz) to monitor is based upon the frequency band
of the IBUC. IF will be automatically converted to RF.

Table C.6 Default Values for the TFR Command
Default Value Default Value

Model Number Model Number
(MHz) (MHz)
057064 6075 137142 14000
058064 6137 137145 14125
058066 6250 140145 14250
058067 6287 173181 17700
064067 6575 181184 18250
067070 6875 290300 29500
079084 8150 295300 29750
127132 13000 300310 30500
128133 13050 305310 30750
TGC
Description: Displays or sets the operating mode of the Cyber Hardened IBUC 2,
IBUC 2e, IBUC 2G, IBUC R or IBUC G. When using AGC or ALC, the IBUC
power levels must be set prior to closing the loop.
Query: TGC
Q
Response: TGC=<Control Type>
Command: TGC=<Control Type>

C
Response: TGC=<Control Type>
Parameter:
<control type>
0 – Open loop
1 – Automatic Level Control (ALC)
2 – Automatic Gain Control (AGC)
TGL
Description: Displays the gain and level targets for AGC or ALC. This is a read-only
command.
Query: TGL
Q
Response: gain_target = <xx.xx>, level_target = <yy.yy>
Parameter:
<xx.xx>
AGC gain target in dB [decimal number]
<yy.yy>
ALC level target in dBm [decimal number]
TGR
Description: Displays or resets the gain control of the Cyber Hardened IBUC 2,
IBUC 2e, IBUC 2G, IBUC R or IBUC G.
Query: TGR
Q
Response: TGR=<xx.x>
Command: TGR=0
C
Response: Gain Control Reset
Parameters:
<xx.x>
Delta (in dB) from the attenuator setting when AGC/ALC was activated [decimal
number]

TPB
Description: Displays or sets the Gain Settings bits. This Query is used to retrieve the
current settings for Gain. That includes Gain Control, Gain Settings, and Temperature
compensation bits.
Query: TPB
Q
Response: TPB=<xxxx>, <xxxx>, <xxxx>
Parameters:
<Value>
1 = Gain Settings / 2 = Gain control Bit / 3 = Temperature Compensation Bits.
These parameters must be valid numbers between “1” and “4095”. Note that does
not include “0”.
TPM
Description: Displays or configures the power monitoring mode of the Cyber

Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or IBUC G. When TPM is
configured for burst, the TBT must also be set. Default values for the TBT command
are given in Table C.4 on page C-45. If CW is selected, power is read continuously. If
burst is selected, the power reading only changes when a valid burst is detected.
Query: TPM
Q
Response: TPM=<Value>
Command: TPM=<Value>
C
Response: TPM=<Value>
Parameters:
<Value>
0 = CW / 1 = Burst
TPO
Description: Displays the current output power of the Cyber Hardened IBUC 2,
IBUC 2e, IBUC 2G, IBUC R or IBUC G. If TPM is set to burst, this will be the last
valid burst sample of the output power. Use the TFR command to configure the
desired frequency to be monitored. This is a read-only command.
Query: TPO
Q
Response: Tx Output Power=<xx.xx> dBm
Parameters:
<xx.xx>
Current output power [decimal number]
TPT
Description: Displays or sets the attenuator of the Cyber Hardened IBUC 2, IBUC 2e,
IBUC 2G, IBUC R or IBUC G.
Query: TPT
Q
Response: TPT=<xx.x>
Command: TPT=<xx.x>
C
Response: TPT=<xx.x>
Parameters:
<xx.x>
IBUC attenuation [0 to 30 dB].

TSD
Description: Displays or sets the transmit power output delay before the transmitter is
enabled. When configured, the Tx output will be muted for the time period configured.
Query: TSD
Q
Response: TSD=<value>
Command: TSD=<value>
C
Response: TSD=<value>
Parameters:
<Value>
Power up delay before transmitter is enabled [0–500 seconds]
TSP
Description: Displays or sets the state of the Tx output at power up.
Query: TSP
Q
Response: TSP=<State>
Command: TSP=<State>
C
Response: TSP=<State>
Parameters:
<State>
0 – Tx output OFF / 1 – Tx output ON
TST
Description: Displays or sets the state of the Tx output. This command can be
overridden by alarms.
Query: TST
Q
Response: TST=<Response Value>, <String>
Command: TST=<Set Value>

C
Response: TST=<Response Value>, <String>
Parameters:
<set value>
0 = disable / 1 = enable
<response value>
0 = disabled / 1 = enabled / 2 = enabled but muted
<string>
0 = ‘Tx Disabled’ / 1 = ‘Tx Enabled, Not Muted’ / 2 = ‘Tx Enabled, Muted’

TTS
Description: Displays or sets the high-temperature shutdown alarm. If the Cyber

Hardened IBUC internal temperature exceeds maximum operating temperature,
enabling this will disable the transmitter until the internal temperature cools by 20º C,
then will enable the transmitter. Disabling this could cause damage to the IBUC,
therefore caution should be exercised.
Query: TTS
Q
Response: TTS=<State>
Command: TTS=<State>
C
Response: TTS=<State>
Parameters:
<State>
0 = Disable Shutdown / 1 = Enable Shutdown.
TTT
Description: Displays the number of total hours the transmitter has been enabled (that
is, with the transmit signal ON and the mute OFF) since leaving the factory.
Query: TTT
Q
Response: TTT=<Hours>
Parameters:
<Hours>
Number of hours transmitter has been ready to transmit or transmitting [Integer]
TZO
Description: Displays or configures the NTP Server Timezone Offset. TZO can be set
from -12 to 14 hours.
Query: TZO
Q
Response: TZO=<±hh:mm>
Command: TZO=<±hh:mm>
C
Response: TZO=<±hh:mm>
Parameters:
<±hh:mm>
Time zone offset [hh = hours, mm = minutes]. This parameter can assume positive
or negative values.
Other Kinds of Commands & Queries
This section presents a list of other valuable queries, commands, or shortcuts for a
better experience during the unit operation.
CTRL + C
Description: CTRL + C command would log your user off the unit faster.
Response: “Connection to <IP address> closed”.
CTRL + D
Description: CTRL + D command would close your connection to the unit System.
Response: “Connection to <IP address> closed”.

Enable CTRL + Shift + V / C in Windows Command Prompt
Description: Use CTRL + SHIFT + V to “paste” or use CTRL + SHIFT + C to “copy”

content from or to your command prompt.
In order to do so you must enable this feature in your omputer following the steps;
• Open your Command Prompt.
• You may do so typing “CMD” + “Enter”, on windows search bar.
• Right-click anywhere in the command prompt.
• If it does not work, right-click on the upper title bar.
• Enable the function through the steps:
• Find the “Options” label.
• Find the “Edit options” box.
• And check “Use CTRL+SHIFT+C/V as Copy/Paste shortcuts, regardless of
input mode.”
• Hit “Ok” to save your preferences.
• And now you can use the new shortcut to “copy” and “paste” text
List of Commands & Queries Not Supported on SNMP Versions

v1 and v2
This section presents a list of codes, commands, and queries that the SNMP versions
v1 and v2 do not support.
• STA
• STD
• SNA
• SND
• SUA
• SUD
D
A PPENDIX
COMPONENT SPECIFICATIONS AND

CHAPTER0
REFERENCE DRAWINGS
This chapter contains component specifications and outline drawings for the Terrasat
Communications, Inc. line of C-band, X-band, Ku-band and Ka-band intelligent block
upconverters (IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC G), power supply
units (PSUIs), low-noise block converters (LNBs), associated interface units and
accessories supplied with IBUC 2, IBUC 2e, IBUC 2G, IBUC R and IBUC G
systems.
Reference Drawings
Outline drawings are subject to change without notice. To ensure that the latest
information is available, contact Terrasat.
Reference Drawings | D-1

Figure D.2 Fabrication Drawing, FBD-21012-XXXX, Rev A
D-2 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Component Specifications and Reference Drawings
Figure D.3 Fabrication Drawing, FBD-21984-XXXX, Rev B, page 1 of 2

Figure D.4 Fabrication Drawing, FBD-21984-XXXX, Rev B, page 2of 2
Figure D.5 Fabrication Drawing, FBD-20606-XXXX, Rev A

Figure D.6 Example Installation Drawing, IND-10521-0011, Rev A
Data Sheets
Refer to the datasheets in Terrasat, Inc. web site: www.terrasatinc.com.
Product specifications are subject to change without notice. To ensure that the latest
information is available, contact Terrasat.
Data Sheets | D-7

D-8 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Component Specifications and Reference
E
A PPENDIX
FIRMWARE UPGRADE
CHAPTER0
Continuous improvement requires diverse development processes. Therefore, new

features or bug fixes might occur, improving functionality offered by the Cyber
Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, or IBUC G. Hence, the user is
encouraged to always maintain the IBUCs firmware up to date.
The steps shown in this appendix provide the user with a guide on how to perform
such updates to the IBUCs firmware.
Note: The steps provided below are valid only for firmware revisions v0.39 and above. If
your IBUC does not meet these requirements, please contact Terrasat Inc. Technical
Support. For more info, see Repair Policy on page 6-8.
Update Procedure
Firmware updates to the Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R or
IBUC G are done through the web, thus, ensure that you have TCP/IP connection to
the device. Check how to connect to your IBUC unit on pages page B-1 through
page B-4. Once stable connection to the unit is ensured, follow the steps below.
! CAUTION
For Cyber Security reasons, we support and recommend “HTTPS” for firmware
upgrade. Please, always use “https://<IP address>” for the URL instead of “http:/
/<IP address>”.
The downloadable packages for Updates and Upgrades are designed for use in their
respective IBUC models. Consider:
• They do not work in any other models and may cause total system inoperability
and damage.
• In those circumstances, the inoperable IBUC will require a return to the factory
to fix.
• Therefore, pay extra attention to the serial numbers and make sure you
downloaded the correct file version, compatible with your equipment serial
number.
• Always read all the instructions files such as "Read Me" file or “How to” files
inside the ZIP folder downloaded. Follow those instructions before Uploading it to
the system. It helps preventing mistakes related to version compatibility.
! WARNING
Upgrading IBUCs with inadequate update files will cause the IBUC to become
inoperable and require a return to the factory to fix. So, please, double check if
the file version is adequate for the equipment before uploading and upgrading it.
Note: The Upgrading/Updating process must use the supplied/downloaded upgrade utilities:
• ArmSerialDownloader.exe and
• ArmUdpDownloader.exe. (this is the preferred program for upgrading).
How to Update step by step

1. Download the latest firmware version on Terrasat Inc. website (https://
terrasatinc.com/resources/firmware-updates/). Once downloaded, the user should
have a compressed zip file. It should look like ibb_vX_YY.zip, where X and YY
refers to the major and minor update numbers. Extract all contents from the file
and verify that the file named ibb_vX_YY.swu is present. See Figure E.1 for
reference.
Example: If the firmware version downloaded is version 0.41, one should
download ibb_v0_41.zip file, which should contain ibb_v0_41.swu file.
E-2 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Firmware Upgrade
Figure E.1 Firmware Upgrade File

2. Open any web browser and access port 8080 of the IBUC. This can be
accomplished by appending “:8080” after the IBUCs IP address.
Example: If the units IP address in the local network is 192.168.1.21, to access
port 8080, the user should type https://192.168.1.21:8080.
Once accessed, the web browser should show a page as the one on Figure E.2.
Figure E.2 Software Update Web Page
Update Procedure | E-3

3. Once opened, drag and drop the “swu” file to the software update area, or, click the
software update area and select the “swu” file from the File Upload menu.
Once done correctly, the file should automatically start being uploaded to the unit.
Refer to Figure E.3.
Figure E.3 Software Update progress
4. Once the upload process has been finished successfully the system will
automatically reboot.
Figure E.4 Software Update Wait for Reboot

5. Upon complete reboot & system upgrade, the software update page will come back
to its original state, asking for firmware upgrades. The unit is now updated and can
be used.
Note: If the user is not sure if the firmware upgrade has been successful, access the
Information of the Embedded Web Pages (see Information on page B-7) or
through the CCS ASCII command (see CCS on page C-8).
Update Procedure | E-5

F
A PPENDIX
GLOSSARY
CHAPTER0
Glossary of Terms
The following acronyms are used in Terrasat Communications, Inc. documentation:
°C Degrees Celsius
°K Degrees Kelvin
1RU One Rack Unit (1.75 in.)
s Microsecond
AC Alternating Current
Admin Administrator
AES Advanced Encryption Standard
AGC Automatic Gain Control
ALC Automatic Level Control
AWG American Wire Gauge
ATE Automated Test Equipment
ATP Acceptance Test Procedure
BER Bit Error Rate
BUC Block Upconverter
CSM Continuous Signal Mode
CW Continuous Wave
DAB Digital Audio Broadcasting
dB Decibel
dB/oct Decibel per Octave
dBc Decibel Below Carrier

dBm Decibel referenced to 1 milliwatt
DC Direct Current
DCE Data Communication Equipment
DRO Dielectric Resonator Oscillator
DTE Data Terminal Equipment
DVM Digital voltmeter
EMC Electromagnetic Compatibility
EMI Electromagnetic Interference
ERM Electromagnetic Compatibility and Radio Spectrum Matters
fr Frequency
FSK Frequency Shift Keying
FSS Fixed Satellite Services
F/W Firmware
g Gravity
GHz Gigahertz
GUI Graphical User Interface
HHT Hand-held Terminal
HPA High-Power Amplifier
HPC High-Power Converter
HTTP Hypertext Transfer Protocol
HTTPS Hypertext Transfer Protocol Secure
Hz Hertz
I/O Input/Output
IBB IBUC Cyber Hardened Version
IBUC Intelligent Block Upconverter
IDU Indoor Unit
IF Intermediate Frequency
IFL Interfacility Link
IP Internet Protocol
kg Kilogram
LNA Low Noise Amplifier
LNB Low Noise Block Converter
LO Local Oscillator
F-2 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Glossary
M&C Monitor and Control
max Maximum
MCPC Multiple Carrier Per Channel
MHz Megahertz
MIB Management Information Base
min Minimum
ms Millisecond
MTBF Mean Time Between Failure
MUC Microwave Upconverter
ns Nanosecond
OCXO Oven-controlled Quartz Oscillator
ODU Outdoor Unit
OID Object Identification or Object Identifier
OMT Orthogonal Mode Transducer
p-p Peak to Peak
P1dB Power at the 1dB Compression Point
PFC Power Factor Corrected
PLDRO Phase-Locked Dielectric Resonator Oscillator
PLL Phase-Locked Loop
PLLNBC Phase-Locked Low-Noise Block Converter
PLO Phase Locked Oscillator
ppb Parts Per Billion
ppm Parts Per Million
PSUI Power Supply Unit
Pwr Power
QTP Qualification Test Procedure
QPSK Quadrature Phase Shift Keying
RF Radio Frequency
RFT Radio Frequency Transceiver
RH Relative Humidity
RMS Root Mean Square
RPL Rated Power Level
RTC Real Time Clock
Glossary of Terms | F-3

RTS/CTS Request to Send/Clear to Send
Rx Receive
s Second
SCPC Single Carrier Per Channel
SHA Secure Hash Algorithm
SNG Satellite News Gathering
SNMP Simple Network Management Protocol
SNMPv3 SNMP version 3.0 protocol
SSB Single Side Band
Secure Shell Protocol (Cryptographic Network Protocol for

SSH
Cyber Security)
SSHv2 Secure Shell Protocol Version 2.0
SSPA Solid-State Power Amplifier
TCP/IP Transfer Control Protocol/Internet Protocol
TRF Transmit Reject Filter
Tx Transmit
UDP User Datagram Protocol
UPC Upconverter
UPS Uninterruptible Power Supply
v1 Version 1
v2 Version 2
v3 (USM) Version 3 (User-based Security Model)
VAC Volts Alternating Current
VDC Volts Direct Current
VSAT Very Small Aperture Terminal
VSWR Voltage Standing Wave Ratio
VVA Variable Voltage Attenuator
W watts
WG Waveguide
F-4 | Cyber Hardened IBUC 2, IBUC 2e, IBUC 2G, IBUC R, IBUC G Operations Manual: Glossary
INDEX
Numerics configuring SNMP, 5-4

10 MHz reference signal continuous signal mode
priority, 2-16 IBUC power measurement, 5-5
CSM
See continuous signal mode
A
adjusting system gain, 3-14 D
alarm log
incorrect time stamp, 4-8 DC block, 3-21
alarms default transmit alarms, 5-2
default configuration, 5-2 differential mode, 6-2
antenna mounting options, 3-8 noise, 6-2
ASCII commands disconnect devices, 3-6
common, B-1
attenuation, 2-22, 2-23 E
setting, 3-22 Ethernet
automatic gain control (AGC), 2-22 SNMP, 5-4
automatic level control (ALC), 2-22, 4-5
available bands, 2-2 F
avoiding factory configuration
signal saturation, 4-9 IP address, 5-3
IP gateway, 5-3
B subnet mask, 5-3
block diagram Telnet, 5-3
AC-powered IBUCs, 2-20 floating supply, 3-16
DC-powered IBUCs, 2-19 frequency plans
IBCU 2e, 2-21 transmit, 2-3, 2-4, 2-5, 2-6
breather valve, 3-12 fuses
burst mode marking schema, 2-15
power measurement, 5-5 requirements, 2-13
C G
checks gain, 2-18
M&C, 6-2 adjusting, 3-14
power supply, 6-3 galling, 3-3
common mode, 6-2
noise, 6-2 I
transients, 6-2 IBUC
gain, 2-18
L-band input, 2-16
Index-1
power measurement Plenum cables
burst mode, 5-4 use of, 3-14
continuous signal mode, 5-4 power issues, 6-1
required inputs, 2-16 power measurement
system configurations, 2-23 to ?? modes, 5-4
IEC protection class, 3-6 power protection devices, 6-2
IFL power supply checks, 6-3
See interfacility link pressure window, 3-12
indoor power supply pressurizing, 3-12
applications, 3-7 priority, 3-14
interface frequency, 2-2 reference signal, 3-14
interfacility link pure carrier, 3-22
definition, 2-2
IP address R
default, 5-3 reference documents
IP gateway, 5-3 satellite operation, 1-2
isolation filter, 3-4 reference signal, 3-14
priority, 2-16
L repair policy, 6-8
L-band input, 2-16 replacement fuse type, 4-7
low-consumption IBUC 2e, 2-8 returned material authorization, 6-8
RF signal flow
M required inputs, 2-16
M&C interfaces RMA procedure, 6-8
Ethernet RS232
SNMP, 5-4 initiating a session, 5-1
multifunction LED, 5-2
RS232, 5-1 S
mastic tape saturation
application, 3-18 transmit power, 6-3
maximum voltage drop, 3-14 signal saturation
MIBs, 5-4 avoidance, 4-9
mounting hole, 3-11 single sideband
phase nose, 2-16
N SNMP
noise, 6-2 configuration, 5-4
normal mode, 6-2 MIBs, 5-4
transverse mode, 6-2 traps, 5-4
normal mode, 6-2 solid-state power amplifier, 2-18
transients, 6-2 standards
satellite operation, 1-2
P
phase noise
external reference, 2-16
internal reference, 2-16
Index-2
storage limitations, 2-28

subnet mask, 5-3
supply voltage options, 2-8
system gain adjustment, 3-14
system requirements, 2-23
T
thresholds
Tx Input, 4-4
Tx Output, 4-4
time stamp
incorrect data, 4-8
transceiver faults, 6-1
transients
common mode, 6-2
normal mode, 6-2
transmit alarm default configurations, 5-2
transmit frequency plans, 2-3, 2-4, 2-5, 2-6
transverse mode
noise, 6-2
traps
SNMP, 5-4
U
Ufer ground, 3-7
V
variable attenuator, 2-23, 3-14
voltage
drop, 2-24
options, 2-8
ranges, 2-8
voltage drop
maximum, 3-14
W
warranty policy, 1-5
warranty seals
breaking, 1-6
waveguide, 3-12
flange types, 2-18
Index-3
Index-4

Terrasat IBUC 2 IBUC 2e IBUC 2G IBUC R IBUC G Operations Manual - Terrasat Communications

Uploaded by

Copyright:

Available Formats

Terrasat IBUC 2 IBUC 2e IBUC 2G IBUC R IBUC G Operations Manual - Terrasat Communications

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Terrasat IBUC 2 IBUC 2e IBUC 2G IBUC R IBUC G Operations Manual - Terrasat Communications

Uploaded by

Copyright:

Available Formats

Engineered to Endure

Cyber Hardened Intelligent Block

24-Hour Technical Support Phone: +1 669.258.9740

Part Number: O&M-22062-0003

© September 2021 Terrasat Communications, Inc.

315 Digital Drive Phone: +1 408.782.5911

Chapter 2, Functional Description

System Pressurization ....................................................................................................... 3-12

Chapter 5, Monitor and Control Features

Site-Related Problems....................................................................................................... 6-2

Appendix A, Part Numbering Schema

Appendix B, Embedded Web Pages

Appendix C, ASCII Command/Response Structure

SHL ................................................................................................................................... C-31

Appendix D, Component Specifications and Reference Drawings

Appendix E, Firmware Upgrade

Table P.1 Typographical Conventions ........................................................................................ P-1

Figure B.18 Statistics Charts ......................................................................................................... B-27

Revision Date Description

Added Appendix B, Embedded Web Pages

Included updates and new safety features (Cyber Hardened)

Updated Firmware and web pages versions and features

Updated Copyright terms and terms of use

Updated Introduction chapter

Updated Installation chapter

Updated Operation chapter

Updated Appendix A, Part Numbering Schema

Updated Appendix B, Embedded Web Pages

Updated Appendix C, ASCII Command Response Structure

Conventions and References

Table P.1 describes typographical conventions used in Terrasat Communications, Inc.

Table P.1 Typographical Conventions

Cautions and Warnings

Electrical Safety Notice

• Know how to work around, with, and on high-voltage equipment.

• Installation, operation, and maintenance of Cyber Hardened IBUC 2, IBUC 2e,

Our Intelligent Block Upconverters, the IBUC

Our Cyber Hardened IBUC

Table 1.1 Satellite Operation Standards

Reference Documents | 1-3

Table 1.1 Satellite Operation Standards (Continued)

Table 1.1 Satellite Operation Standards (Continued)

Cyber Security Best Practices

Reference Documents | 1-5

Warranty Information | 1-7

System Components | 2-2

Table 2.1 IBUC 2 Transmit Frequency Plans

Table 2.2 IBUC 2e Transmit Frequency Plans

Output Power 4, 8, 12, 16 watts 4, 8, 12, 16 watts 4, 8, 12, 16 watts

System Components | 2-4

Table 2.3 IBUC 2G Transmit Frequency Plans

Signal Ka-band Ka-band

L-band 1000 MHz to 1500 MHz 1000 MHz to 2000 MHz

RF frequency 29.500 GHz to 30.000 GHz 30.000 GHz to 31.000 GHz

Table 2.4 IBUC R Transmit Frequency Plans

100, 125, 150, 175, 200,

System Components | 2-6

Table 2.5 IBUC G Transmit Frequency Plans

Signal Ka-band Ka-band