0% found this document useful (0 votes)
131 views13 pages

Neos Quick Ref Manual

This document provides instructions for programming classes of service and system settings on a NEOS phone system. It includes commands for setting features for each class of service like call forwarding, do not disturb, and time limits. System setting commands configure the date and time, office hours, holidays, card and port additions, and other options.

Uploaded by

Sunil Dhumal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
131 views13 pages

Neos Quick Ref Manual

This document provides instructions for programming classes of service and system settings on a NEOS phone system. It includes commands for setting features for each class of service like call forwarding, do not disturb, and time limits. System setting commands configure the date and time, office hours, holidays, card and port additions, and other options.

Uploaded by

Sunil Dhumal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

QUICK REFERENCE GUIDE - NEOS

I – Class of Service Programming


1 #69+PW+000 + CoS Tbl(01-32) + *
Feature Code (00-14,25-35)+ Func (0/1)+ *
00 – Listening In & Room Monitor
01 – Barge-in with Tone
02 – Barge Protect
03 – conference
04 – Do Not Disturb
05 – Junction Transfer Allow
06 – Call Forward Protect
07 – Second JUN Call
Set class <class 1-32> <clscode>
08 – Only Abbreviated Allow
<limit>
09 – Emergency No. Allow
Limit : 1 – Enable; 0 – Disable
10 – Internal Call Forward Allow
*- Not applicable for 256P CPU
Enable/Disable feature for Class 11 – CLIP Allow
Tables 12 – CLI Restriction Allow
#- Applicable only with Split
13 – CLI Restriction Override Allow
CPU Vr. 0.3, ARM CPU 0.7
14 – Do Not disturb Override Allow
Combo CPU Ver. 1.1 and 256P
25 – Executive Ring Allow*
CPU Ver. 2.0 onwards.
26 – External Call Forwarding*
27 – JUN – JUN Transfer
28 – DTMF / PULSE
29 – DIAL TONE MESSAGE
30 – Mobile Parallel Ring*
31 – DOSA
32 – MSN Call Queue
33 – MSN No Reply
34 – Call Queue on Analog Junction
35 – Enblock Dialing#
#69+PW+000 + CoS Tbl(01-32) + * + 15 + Day Set Class <Class 1-32> <15>
Func(0-4) + Night Func (0-4) + * <limit>
Feature 15 : Day/Night Class
0 – Intercom; 1 – Local;
2 – Local+Mobile 3 – STD; 4 - ISD
#69+PW+000 + CoS Tbl(01-32) + * Set Class <Class 1-32>
Feature 16,17 : Restricted/Denied Feature Code (16/17) + Table (0/1-8/9) + * <16/17> < limit>
Tables 0 – Clear Table ; 1-8 –Selective Table (1-8) 9 –
Assign all Tables
#69+PW+000 + CoS Tbl(01-32) + * + 18 + Func Set Class <Class 1-32> <18>
F-18 : CoS after budget Exhaustion
(0-4) + * < limit>
#69+PW+000 + CoS Tbl(01-32) + * Set Class <Class 1-32> <19/20>
F19,20 : Time Limit Local-STD Feature Code (19/20) + Func (00-99) + * <limit>
00-99 Minutes
#69+PW+000 + CoS Tbl(01-32) + * + 21 + Set Class <Class 1-32> <21>
F21 : Charge Type
Charge Type (0-4) + * <limit>
#69+PW+000 + CoS Tbl(01-32) + * + 22 + Hook Set Class <Class 1-32> <22>
F-22 : Hook Flash Time Flash Digit (1-9) + * <limit>
Digit : 1-9  100 msec – 900 msec.
#69+PW+000 + CoS Tbl(01-32) + * + 23 + Set Class <Class 1-32> <23>
F23 : Voice Prompt Language Language (0-2) + * <limit>
0 – English; 1 – Hindi; 2 – No Prompts
#69+PW+000 + CoS Tbl(01-32) + * + 24 + LCR Set Class <Class 1-32> <24>
F24 : LCR Type Type (0-2) + * <limit>
0 – No LCR; 1 – LCR Override ; 2 – Only LCR
#69+PW+000 + CoS Tbl(01-32) + * Set Class <Class 1-32> <25>
F25 : Executive Ring
25 + Func (0/1) + * <limit>
#69+PW+001 + Source Class (01-32) + Set copycls <Source class>
2 Copy Class
Destination Class (01-32) + * <Destination Class>
Set asscls <Ext No> <class no.:1-
3 Assign class to Extension #69 +PW + 002 +Ext No + Class No. (01-32) + *
32>
II - System Setting
Set time <HHMM>
1 RTC Time setting #69 +PW + 011 + HH + MM + *
Set date <DD><MM><YY><DoW
2 RTC Date Setting #69 +PW + 012 + DD + MM + YY + DoW + *
1-Mon…..7-Sun>
Set officetime
#69 +PW + 013 + DoW + HH1 +MM1 + HH2 <DoW:1=Mon….7=Sun/8=Mon-
3 Office Time Setting
+MM2 + * Sat><Start TimeHHMM> <End
Time HHMM>
4 Clear Office Time #69 +PW + 014 + 0 + * Clear officetime
5 Set Organizational Holiday #69 +PW + 015 + DD + MM + * Set holiday <DDMM>
6 Clear Organizational Holiday #69 +PW + 016 + 1234 + * Clear holiday
7 Change over Mode #69 +PW + 017 + Func (1/2) + * Set mode <digit:1-Manual/2-Auto>
Set daynight <Digit:1-Night/2-
8 Manual system Mode Changeover #69 +PW + 018 + Funct (1/2) + *
Day>
#69 +PW + 019 + slot No. (1-7/01-16) + Card Set cardadd <slot no 1-7/01-16>
9 Add Card
Type (01-17) + * <Card type 01-17>
10 Delete Card #69 +PW + 020 + Slot No. ( 1-7 / 01-16) + * Clear card <slot no 1-7 / 01-16>
Add Port / Assign Ext. No. to port #69 +PW + 021 + Port No. (001-128-160-256) + * Set portadd <port no:1-128-160-
11
FNP + Ext. No. + * 256> <Ext No.>
Assign program Access Level to #69 +PW + 022 + Ext. No. + Program Access Set extpacc <Ext No> <Program
12
Ext. Level ( 0 / 3) + * Access Level-0/3>
13 Program CTI FNP #69 +PW + 024 + CTI Mode (0-4) + * Set ctimode <mode:0-4>
Set prpwchng <3> <4 digit
14 Change Program PW #69 +PW + 025 + 3 + New PW + *
password>
#69 +PW + 028 + Day mode Music (0/1) + Night Set music <day: 0/1><Night: 0/1>
15 Music Source selection
Mode Music ( 0/1) + *
Voice Guidance language selection Set vglang <Digit: 0-2>
16 #69 +PW + 029 + Language ( 0-2)
for External caller
Set Dial Plan for Extension #69 +PW + 047 + Digit (0-5) + Dial Type (1-5) + Set dialplan < digit 0-9>
17
Numbering * < dial Type 1-5>
Adding dummy zeros for CLI #69 +PW + 048 + Digit (0-5) + Mode (0- Suffix / set clidummy <digit: 0-5>
18
Display 1 – Prefix ) + * <Digit = 0 :Suffix / 1=Prefix>
set clisend <0/1 0=Before ring 1=
19 Setting CLI send Pattern # 69 + PWD + 049 + Digit (0-1) + *
Between ring>
III - FLEXIBLE NUMBERING PLAN
1 Clear Dial Code FNP #69 + PW + Prg.code 094 + Port No./999 + * clear DIALCode <Port No/999>
# 69 + PW + 092 + Port No <000-258, 276-285> set DIALC <Port no>
2 Program Dial code FNP
+ Dial Code <x-xxxxx> < Dial Code>
3 Restore Default Dial Code FNP #69 + PW + 096 + 1234 + *
4 Clear Feature Code FNP #69 + PW + Prg.code 095 + Feature No./999 + * clear FEATC < Feature No /999>
#69+1234+<Program code 093>+feature set featcode <feature no> <Dial
5 Program Feature code FNP
no.(xxx)+Dial code<x-xxxxx>+ * code>
6 Recover default feature Code FNP #69 + PW + 097 + 1234 + *
IV – Extension Programming
Set enext < ext no><Digit:1-
1 Extension Enable/Disable #69 +PW + 031 + Ext. No . + Func ( 0/1) + *
Enable/0-Disable>
Set oprext <Ext No./Hunt Group>
2 Set Operator Extension #69 +PW + 032 + Operator Ext. No. + *
(999 – Cancel OPR)
Flexible Number Programming #69 +PW + 033 + Old Ext. no. + * + New Ext. no. Set flex <Old Ext No> <New Ext
3
FNP +* No>
#69 +PW + 035 + Ext.1 + * + Ext2 + * + Ext3 + * Set faxext < extno> <extno>
4 FAX Extension
+ Ext. 4 + * <extno> <extno>
#69 +PW + 036 + Ext. No. + * Set resetexpw < extno.>
5 Reset Extension Password Ext. PW would be set to 1234. No need to set Card if added, Ext. PW needs to
exclusively. be resetted.
#69 +PW + 037 + Ext. No. 1 + * + Ext. 2 + * + Set pickgrp <header ext> <member
6 Add Extension to Pickup Group
……. ext>
Delete Extension from Pickup Clear pickext <extno>
7 #69 +PW + 038 + Ext. No. + *
group
8 Delete Pickup Group #69 +PW + 039 + Ext. No. + * Clear pickgrp <extno>
#69 +PW + 040 + Hot Line No (01-16) + * + Set hotline <hotline number 1-16>
9 Hot line Number Programming
Number + * <digits>

------------------------------------------------------------------------------------------------------------------------------------------------------------------ 2
PROGRAMMING MANUAL Wednesday ,May 05, 2014
Set exthotline <extno> <hotlineno:1-
#69 +PW + 041 + Ext. No. + Hot Line (01-16) +
10 Assigning Hotline No. to Extension 16> <digit:1-Dely/0-
Type (0/1) + Func ( 0/1) + *
Imm> <1>
11 Clear Hot line #69 +PW + 042 + Ext. No. + * Clear hotline
#69 +PW + 154 + Boss Ext. No. + * + Secretary Set secretary <boss extno>
12 Boss secretary Extension FNP
Ext. No. + * <secretary extno>
Assign Junction Group to #69 +PW + 075+ Jun Gr No (01-16) + * + Ext No. Set assjgrp <extno>
13
Extension 1 + * + Ext No. 2 + * + ….. <Jun Grp no: 01-16>
Assign Secondary JUN Group to
14 #69 +PW +098 + Grpno (01-16) + * + ExtNo.+ *
Extension
15 Clear Secondary JUN Group of Ext #69 + PW + 100 + ExtNo + *
V – Analog Junction Programming
Set junen <junno><digit:1-Enable/0-
1 Enable/Disable Junction #69 +PW + 061 + Jun No. + Func (0/1) + * ..
Disable>
#69 +PW + 062 + Jun No + Direction (1-I/C/2- Set jundir <junno> < digit:1-i/C// 2-
2 Junction’s Operating Direction
Bothways) + * Bothways>
Set ajsigtype <jun no> <Type:1-
Pulse/2-Tone> <Category:1-Local/
#69 +PW + 063 + Jun No + Signal Type (1-2) + 2-STD>
3 Junction Type
Category (1-2) + Meter (1-4) + CLIP (1-2) + * Set ajmtrclip <jun no> <Mtr:1-
none/2-Rev/3-12 KHz./4-16KHz>
<Clip: 1-None/2-DTMF>
Set huntgrp <grpno:1-15><Hunt
#69 +PW + 064 + Group No (01-15) + Type (1-3)
type:1-sim/2-busyImm/3-busyDly>
4 Hunt Group Programming + Staircase (1/2) + * + Ext. No. 1 + * + Ext. No. 2
<Staircase:1-On/2-Off><Ext: Max
+ * +……( Max 5 Ext.)
5>
#69 +PW + 065 + Jun No + * + Day Ext. No + * + Set jlanding
Night Ext. No. + * + …… <junno><DayExt><NightExt>
5 Junction Landing Extension FNP
Day /Night Ext No : 910 –Auto ATT / Specific
Ext. No. / Hunt Group (681-690)
6 Hunt Time #69 +PW + 066 + Time (06-60) + * Set hunttime <time:6-60>
set failland <jun no> <Z1 ext> <Z2
#69 +PW + 067 + Jun No + * + Z1 Ext. No. + * +
Attendant Fail Landing ext> <Z3 ext> < Z4 ext>
7 Z2 Ext + * + Z3 Ext + * + Z4 Ext + * Ext No =
Ext =999 will disconnect call during
Specific Ext. No./ Hunt Group No.
respective TZ after welcome msg.
8 Assign Private Junction Line FNP #69 +PW + 068 + Ext. No. + * + Jun No. + * Set junpvt <extno> <junno>
9 Delete Private Junction Line #69 +PW + 069 + Ext. No. + * Clear junpvt <extno>
10 Junction Access Group #69 +PW + 070 +
Not to be used at all.
11 Junction Access Group call limit #69 +PW + 071 +
#69 +PW + 072 + Service Provider ( 0-5) + * + Set junserv <Service Provider no : 0-
12 Junction service Provider Jun No. 1 + * + Jun No. 2 + * + ….. 5> <jun no>
Note : Do not use SP=0 for LCR Prog.
#69 +PW + 073 + Jun Group No. (01-16) + * + Set jungrp <JunGrp no: 01-16> <jun
13 Program Junction Grouping
Jun No. 1 + * + Jun No. 2 + ……. no>
#69 +PW + 074 + Jun Group No + * + Jun No. 1 Clear jungrp <JunGrp no:01-16>
14 Clear Junction Grouping
+ * + Jun No. 2 + * + ….. <Junno>
Set jlease <junno>
15 Program Leased Line #69 +PW + 076 + Jun No + Digit ( 0/1) + *
< Digit:1-Enable/0-Disable>
16 Program Junction Ring Pattern #69 +PW + 077 + Digit (8-5) + * N. A.
17 Program JUN as Centrex Line #69 + PW + 078 + Jun no + 0/1+ * set centrex <junno><digit: 0-1>
Program Time-out for External set efwdtime <time:0-99>
18 #69 + PW + 050 + timeout (01-99)+ *
Forwarded Calls
19 Program Auto ATT Ring Time-out #69 + PW + 051 + timeout (05-30)+ * N. A.
Program time-out for JUN-JUN
20 #69 + PW + 052 + timeout (01-99)+ * N. A.
Transferred Call
set servprov <Digit (0-1)>
Selection of # dialing for Centrex #69 + PW + 055 + Digit ( 0 – AirTel / 1 –
21 0- AirTel # Centrex / 1 – Reliance #
with AirTel / Reliance Reliane) + *
Centrex dialing.
Programming Dummy Dial-tone set Dummydt <Digit (0-1)>
22 #69 + PW + 056 + Digit ( 0 – OFF / 1 – ON ) + *
for Analog Junctions 0- Dummy DT OFF ; 1 - ON

------------------------------------------------------------------------------------------------------------------------------------------------------------------ 3
PROGRAMMING MANUAL Wednesday ,May 05, 2014
Call Forward of Hunt group to #69 + PW + 057 + H.G. (01-10) + FWD Type (0- set fwdhunt <H.G.><Type : 0-2>
23
Hunt Group / Extension 2) + Call Type (1-4) + Ext. / H.G. / 999 + * <Call Type 1-4> < H.G./Ext/999>
24 Jun Call Queue on Hunt Group # 69 + PW + 058 + Digit ( 1-Enable / 0-Disable ) N.A.
25 Transfer Call Recall time Selection #69 +PW +105 +<Time 15-60> + * set trfrecall<Time(sec):15-60>
Programmable Hunt Group #69 + PW + 217 + <Huntgrp no. 01- set huntland <huntgrp no 01-10>
26
Landing Pattern 10>+<digit:0=Sequential/1=Round robbin> +* <digit:0=sequential/1=Round Rbn>
STD / Local JUN access
27 #69 + PW + 109 + Digit < 0 – OFF / 1 – ON > +* set allowstd <Digit:1=on/ 0=off>
transperancy
28 Programmable Paging Junction #69 + PW + 600 + JUN No. + * set pagejun <JUN No.>
29 Clear Paging Junction #69 + PW + 601 + JUN No. + * clear pagejun < JUN No.>
VI – Auto Attendant Message Programming
#69 +PW + 081 +DoW (1-7) + Z1 Start Time set tzones<dow:1-7>
(XXXX) + Z2 Start Time + Z3 Start Time + Z4 <Z1><Z2><Z3><Z4>
1 Message Time zone Programming
Start Time + * [Z1-Z4:Zone Start time HHMM]
Z1-Z4 : Time Zone in 24 Hrs. format.
Welcome Message Table #69 +PW + 082 + Tbl No. (1-9) + * + Z1 Msg (1-8)
2
Programming + Z2 Msg (1-8) + Z3 Msg (1-8) + Z4 Msg (1-8) + *
3 Assign Message Table to Junction #69 +PW + 083 + Jun No. + Tbl No. (1-9)+*
Record Auto Attendant Message/ N. A.
4 #69 +PW + 084 + Msg. No. (01-09) + *
Music
5 Playback recorded ATT Message #69 +PW + 085 + Msg. No. (01-09) + *
6 Erase Auto attendant Messages #69 +PW + 086 + 1234 + *
VII. – E1 Junction Programming
Set eoglim <junno><Max
#69 +PW + 101 + Jun No. + Max Ch (30) + Max
1 E1 Channel Setting Ch:30><Max OG Ch:0-30><Hunt
OG Ch (00-30) + Direction (1/2) + *
Dir:1-Asc/2-Desc>
Set epara <junno> <Sig:1-Pulse/2-
#69 +PW + 102 + Signal Type (1-3) + 1 +
2 E1 Parameter setting DTMF/3-R2MFC> <1> <Cat:1-
Category (1-Local/2-STD)
Local/2-STD>
#69 +PW + 103 + Jun No + Day Ext. No. + Night Set eland <junno> <DayExt>
3 E1 Landing Extension
Ext. No. + * <NightExt>
VIII. – BRI Junction Programming
#69 +PW + 111 + Jun No. + Max Ch (02) + Max Set brioglim <junno> <Max
1 Channel setting
OG Ch (00-02) + * Ch:2> <Max OG Ch:0-2>
#69 +PW + 112 + Jun No. + Day Ext + Night Ext Set briland <junno> <DayExt>
2 Landing Extension
+* <NightExt>
Set brica <junno>
3 BRI Category #69 +PW + 113 + Jun No + Category (1/2)
< Cat:1-Local/2-STD>
IX. – PRI Junction Programming
# 69 + PW + 169 + <Slot No> + Digit + *
1 CRC Setting Slot No. : 01-16 Digit = 0 : CRC Off SET PRICRC <slot.no> + <0/1>
1 : CRC On
Set prioglim <junno>
#69 +PW + 115 + Jun No. + Max ch(30) + Max
1 Channel Setting <Max Ch:30> <Max OG Ch:0-30>
OG Ch.(00-30) + Channel Selection (0-1) + *
<Ch. Sel. 0/1>
#69 +PW + 116 + Jun No. + Day Ext. + Night Ext Set priland
2 Landing Extension
+* ,junno><DayExt><NightExt.
#69 +PW + 043 + Primary Clock Slot No + Set nwclk
3 Define Network clock Source
Secondary Clock Slot no + * <Slotno:01-16> <SlotNo:01-16>
Set prica <,junno>
4 PRI Category #69 +PW + 117 + Jun No + Category (1/2)
<Digit:1-Local/2-STD>
# 69 + PW + 216 + Type of Number + Numbering
5 Calling Party Number Information N.A.
Plan + *
# 69 + PW + 211 + Private ch table number (1-2)
+ * + Extension no + Ch no (01-15, 16-31) + * +
5 Assign PVT CH to Ext. N. A.
Note: Channel No 0 & 16 are not allowed to make
as Private channel.
# 69 + PW + 212 + Jun. No + Private ch table no
6 Assign PVT CH Table to JUN (1-2) + * N. A.
Private CH. Table = 1 / 2; 9 to clear.
# 69 + PW + 214 + Private ch table no (1-2) +
7 Clear PVT CH No. for Ext. N. A.
Extension No + *

------------------------------------------------------------------------------------------------------------------------------------------------------------------ 4
PROGRAMMING MANUAL Wednesday ,May 05, 2014
Set prichalloc < digit : 0=Sequential;
8. PRI Channel Allocation # 69 + PW + 215 + Digit <0/1> + *
1=Round Robbin>
X. – SIP Trunking
Logical Partitioning #69+ PW + 091 + 1/0 + * set lgclprtn <Digit:0/1>
XI. – VoIP TIE Junction Networking
1. Tie Route Method #69+ PW + 400 + <Method: 1-PBX code set troutmthd <Digit: 1=PBX code/
/0:Ext.Num > + * (Default Ext. Num) 0=Ext. numbering>
2. Own PBX Code #69 + PW +401 + Own PBX code(10-99) + * set pbxcode <code no 10-99>
(Default 0)
3. Auto Route Selection #69+ PW + 402 + ARS: 1=On/0: Off + * set tiears <Digit:1=on/ 0=off >
(Default ON)
4. Tie Digit Timeout #69 + PW + 404 + Dig dial timeout <001 set tiedigtme<time:1-100>
(100msec) - 100(10sec) > + *
5. Tie Leading Digit / Tie Route #69 + PW + 405 + Sr.no (01-16) + Leading dig set tieroutbl <Sr.no(1-16)>
Table (1-4 dig ) + * +1st element (Destination IP 1) + * <Leading dig (max 4 dig)> <1st
+ 2nd element + * + 3rd element + * + 4th element element (Destination IP 1)>
+* <2nd element> <3rd element>
<4th element>
6. Add / Strip Digits #69 +PW + 406 + sr.no (01-16) + Add dig + * + set tieaddsub <Sr.no (1-16)> <add
sub dig cnt + * digits (max 4 dig)> <sub digit(0-9) >
7. Min – Max Digits / Tie Destination #69 +PW + 407 + sr.no(01-16) + Min dig(01-22) set tieminmax <Sr.no (1-16)> <Min
Number Length + Max dig(01-22) + * dig(1-22) > <Max dig(1 -22)>

8. Program SIP Tie Card IP Address #69 +PW + 410 + slot no + *+ IP Addr <1st set TIEIPaddr <slot no> <1st
element> + * <2nd> + * + <3rd> + * + <4th> + element> <2nd Element> <3rd
* Element> <4th Element>
9. Program SIP TIE Card Netmask #69 + PW + 411 +slot no + * +netmask<1st set TIENEtmask < slot no> <1st
element> + * <2nd>+ * + <3rd> + *+ <4th> + * element> <2nd Element>
<3rdElement> <4th Element>
10. Program SIP TIE Card Gateway #69 + PW + prg.code 412 +slot no + * + Gateway set TIEGAteway < slot no>
<1st element> +* + <2nd > + * + <3rd > + * + <1stelement> <2ndElement>
<4th > + * <3rdElement> <4th Element>
11. Program SIP Tie Card dbug Level #69 + PW + 413 +slot no + * + <Debug level 0- set TIEDEbug <solt no > <Debug
7> + * Level 0-7>
12. Load default Tie Parameters #69 + PW + 415 + <slot no> + * set TIEDEF <Slot no.>
13. Restart SIP Tie Card #69 + PW + 414+ <slot no> + * set TIEREStart <Slot no.>
14. Program Alternate destination IPs #69 + PW + 416+ srno(01-16) + IP Add. (02-04) set TIEDEStip <Sr.no 01-16> <IP
in routing Table + * + <1st element> + *<2nd> + * + <3rd> + *+ Add.(2-4)> <1st element>
<4th> + * <2nElement> <3rd Element> <4th
Element>
15. Clear Tie Route Table #69 +PW + 409 +sr.no(01-16)/999 + * clear tieroutbl <Sr.no(01-16)/999>
XII. – CLI Based Routing
Set cliroute ,Sr.No.1-99> <CLI
#69 +PW + 044 + Sr. No.( 01-99) + CLI No. + * +
1 Set CLI Based Routing Table FNP Number:Max 16
Day Ext + * + Night Ext + *
digits><DayExt><NightExt>
Clear cliroute <Digit:0-All;1-
2 Clear CLI Based Routing Table #69 +PW + 045 + Sr. No. (01-99) + *
99:Specific Entry>
CLI based Day-Night landing #69 +PW + 046 + Day Function (0/1) + Night
3 N.A.
Enable/Disable Function (0/1) + *
XII. – MSN Based Routing
#69 +PW + 201 + Jun No + MSN Table No (1-4) Set msntbljun <junno><MSN Tbl
1 Assign MSN table to Junction
+* No:1-4>
#69 +PW + 202 + MSN Table No (1-4) + MSN Set msnnolen <MSN Tbl No : 1-4
2 Program MSN No. length
No. length ( 1-5) + * ><msnnolen:Max 8>
#69 +PW + 203 + MSN Tbl No (1-4) + * + Port Set MSn Port No <MSN Tbl No : 1-
3 Assign MSN number to Port No + MSN No. + * + Port No + MSN No + * 4> <Port No :001-268> < MSN No.
+….. as per MSN No len>
#69 +PW + 204 + MSN Tbl No (1-4) + Port No + Clear MSN Port <MSN Tbl No:1-4>
4 Clear MSN No. for Port No.
* <Port No: 001-145>
5 Clear MSN Number Table #69 +PW + 205 + MSN Tbl No (1-4) + * Clear MSN Tbl <MSN Tbl No.:1-4>
------------------------------------------------------------------------------------------------------------------------------------------------------------------ 5
PROGRAMMING MANUAL Wednesday ,May 05, 2014
6 Clear Pilot Number #69 +PW + 206 + MSN Tbl No (1-4) + * Clear pilotno < MSN Tbl No:1-4>
Program Pilot Number #69 + PW + 207+ MSN Tbl No (1-4) + * + Digits Set pilotno < MSn Tbl No:1-4>
7
+* <Pilot No>
MSN day-Night landing #69 +PW + 208 + MSN Tbl No (1-4) + Day (0/1)
8 N.A.
Enable/Disable + Night (0/1) + *
#69 +PW + 209 + MSN Table No. (1-4) + * +
Set MSNCLIdisp <msntbl no:1-4>
9 Outgoing MSN CLI Display Port No (001-258) + CLI display port No (001-
<port no:1-158><clidisp:1-268>
268) +*
XIII. – GSM Card Features Programming
1. Base Station Programming # 69 + PW + 080 + Digits + * (
Digit :STD code of the base station of the GSM N. A.
card)
2. Programming MIC Gain #69 + 1234 + 220 + <JUN NO> + <GAIN> + * set gsmmic <junno: 000-255>
(Gain : 00-15) <micgain : 00-15>
3. Programming Speaker Gain #69 + 1234 + 221 + <JUN NO> + <GAIN> + set gsmspeaker <junno: 000-
* (Gain : 00-99) 255> <speakergain : 00-99>
4. Programming Side Tone Setting # 69 + PW + 222 + JUN No. + Side Tone + * Set gsmsdtone <junno:000-255>
< sidetone: 00-15>
6. Display IMEI Number # 69 + PW + 224 + Digit <0 – Display IMEI No.
N. A.
/ 1 – Display GSM JUN No.>
XIV. – Restricted & denied Table Programming
#69 +PW + 121 + Tbl No ( 1-8) + * + Number + * Set resttbl < tblno:1-8> <entryno:1-
1 Restricted Table Programming
+ Number + * + ….. 10><digits>
2 Clear Restricted Table #69 +PW + 122 + Tbl No ( 1-8) + * Clear resttbl < tblno:1-8>
#69 +PW + 123 + Tbl No ( 1-8) + * + Number + * Set denytbl < tblno:1-8> <entryno:1-
3 Denied Table Programming
+ Number + * + ….. 10><digits>
4 Clear Denied Table #69 +PW + 124 + Tbl No ( 1-8) + * Clear denytbl < tblno:1-8>
XV. – Abbreviated Dialing
#69 +PW + 131 + Table No ( 01-20) + * + No Set dabrtbl <tblno:1-20> < No. :1-
(00-09) + Digits + * 10> < digits>
1 Abbreviated Table Programming
#69 + PW + 131 + 99 + * + No.(10-99) + Digits + Set sysabr < Sr.No : 10-89 for sys
* abr no./ 90-99 for emerg> < digits>
Assign departmental Abbreviated
2 #69 +PW + 132 + Ext No. + Table No (01-20) + * Set assabr < extno> < tblno : 1-20>
Table to extension
Clear abrtbl < 99-sys abrtbl/98-all
3 Clear Abbreviated Table #69 +PW + 133 + 98 + *
dept.abrtbl/ 1-20- specific dabrtbl>
Extended Abbreviated Table
4 # 69 + PW + 134 + No (000-499) + Digits + * set EXSysabr <0-499> < Digits >
Programming
5. Clear Extended Abbr No. #69 + PW + 135 + <000-499 / 999> + * clear EXAbrtbl <0-499 /999>
XVI. – Call Metering
#69 +PW + 145 + Local Start Time (00-99) +
1 Program Bill Start Time N. A.
STD Start Time (00-99) + *
2 Clear / Initialize Billing Parameters #69 +PW + 155 + Digit (0-3) + * N. A.
#69 +PW + 156 + Digit ( 0- All Calls / 1- Only Set logtype <type= 0-Log all calls /
3 Program Call Type to be logged
OG Calls) + * 1-Log OG calls only>
Set crsrno <call record Sr. No. :
4 Program Call Record #69 +PW + 163 + Log Sr. No. (0000-9999) + *
0000-9999>
XVII. – Billing & cost Tables
Set fprpc < prpctbl:1-25> < fpr:0-
#69 +PW + 151 + PRPC Tbl No (01-25) + FPR
9999> <fpc:0-9999>
1 Program PRPC Table (0000-9999) + PR (0000-9999) + * + FPC(0000-
Set prpc <prpctbl:1-25> <pr:0-9999>
9999) + PC(0000-9999) + *
< pc:0-9999>
#69 +PW + 152 + Service Pro No (0-5) + CCT No
Set cct <sp no:0-5> < cct no :1-16>
(01-16) + * + Zone start Time for Zone 1
2 Program Call cost Table [<TZ1st t ime:HHMM> <prpctbl:1-
(HHMM) + PRPC Tbl for Zone1 (01-25) + * +
25>….uptp 4 TZ>]
….. ( Max 4 time zones)
Set std <code sr. no. :1-99> <
#69 +PW + 153 + Code sr. No. (01-99) + Code
Assigning Cost Tables to Local / code> <CCT sp0> <CCT sp1>
3 Digits (00-99) + * + CCT for SP0 ( 01-16) + *
STD / ISD Codes. ….<CCT sp5>
+ CCT for SP1 (01-16) + * + ….(Max. 5 SP)
(CCT :1-16)
Assigning Pulse Rate for Centrex #69 + PW + 164 + Jun no + FPR(xxxx) +
4. N. A.
Junction Line PR(xxxx)+ *+ FPC(xxxx) + PC(xxxx) + *

------------------------------------------------------------------------------------------------------------------------------------------------------------------ 6
PROGRAMMING MANUAL Wednesday ,May 05, 2014
XVIII. – Least cost Routing
Set LCRPr<entryno> <prefix
#69 +PW + 157 + Entry No (01-25) +
0 - XXXX><localSP1> <STD
1 Program LCR Prefix Prefix (X-XXXXX) + * + Local SP CH1(1-5) +
SP1><localSP2> <STD SP2>
STD SP CH1 + Local SP CH2 + STD SP CH2 + *
[SP:1-5]
#69 +PW + 160 + Entry No. (01-25 for specific/99 Clear LCRPR <entryno 1- 25 or 99
2 Clear LCR Prefix
for all) + * for All>
#69 +PW + 158 + Code Sr. No (01-10) + SP Set lcrcode <code sr no: 1-10 >
3 Program LCR Code CH1(0-5) + SP CH2 (0-5) + LCR Code (0- <code:max 7 digits><SP Ch 1> <SP
9999999) + * Ch2> [ SP – 1-5]
Clear lcrcode <code sr no:1-10 / 99
4 Clear LCR Code #69 +PW + 159 + Code Sr. No. + *
for all entries>
#69 + PW+ 165 + Entry (01-15) + Centrex Length
5 Set Centrex Table (1-6) + Serv.Prov. (1-5) + Modify Flag (0-1) + * + N.A.
Digit/s (1-99) + *
6. Clear Centrex Table #69 + PW + 166 + Entry (01-15 / 99) + * N.A.
#69 + PW+ 167 + Serv. Prov.(1-5) + strip Digit
7. Set Modify Number Table N.A.
(0-9) + Add digit (0-99999) + *
8. Clear Modify Table #69 + PW + 168 + Serv. Prov. (1-5) + * N.A.
XIX. - Budgeting
Set fixbud <Jun/Ext> <Day bud : Rs.
#69 +PW + 161 + Ext. No/Jun No.+ Day Budget
1 Program Fixed Budget 0-9999> <Month Bud : Rs 0-
+ Month Budget + *
999999>
#69 +PW + 162 + Ext. No/Jun No.+ Day Budget Set enhbudget <Jun/Ext> <Day bud :
2 Program Enhanced Budget + Month Budget + * Rs. 0-9999> <Month Bud : Rs 0-
999999>
XX. – Closed User Group
#69 +PW + 171 + CUG No (01-16) + * + Ext No. Set cuggrp < ext no> <CUG tbl no:
1 Assign CUG number to Extension
+ * + Ext No. + * + ….. 1-16>
#69 +PW + 172 + CUG No (01-16) + * + CUG Set cugen <CUG tbl no: 1-16>
2 CUG call Enable (allow calling)
No (01-16) + * + …… <CUG tbl no: 1-16>
#69 +PW + 173 + CUG No (01-16) + * + CUG Set cugdis <CUG tbl no: 1-16>
3 CUG Call Disable
No (01-16) + * + …… <CUG tbl no: 1-16>
XXI. – CoS Prefix Table Programming
#69 +PW + 088 + CoS Prefix Digits ( max 4) + * Set cosprefix <prefix: max 4 digits>
1 Program CoS Prefix Table + CoS (1-4) + Min Digits ( 03-23) + Max Digits ( < CoS:1-4> < mindig:3-23> <
03-23) + * mazdig : 3-23>
2 Initialize Default CoS Prefix Table #69 +PW + 089 + 1234 + * Clear cosprefix
XXII. – Administrator Programming
1. Set Ring Repetition Pattern # 69 + PW + 077 + Digit (5-8) + * N.A.
2. Program CTI / HMS Integration # 69 + PW + 024 + Digit (0 – 4) + * Set CTI Mode < 0 – 4>
3. Set dial Plan # 69 + PW + 047 + Digits (0-9) + Set Dial Plan <digit 0-9>
Dial Type <1-5> + * <Dial Type 1-5>
4. Program CLI dummy digits # 69 + PW + 048 + Digits (0-5) + Prefix/Suffix + * Set CLIDU <Digit1> <Digit2: 0/1>
5. Program CLI Ring Setting # 69 + PW + 049 + Digit ( 0 / 1) + * Set CLISEND <Digit 0/ 1>
6. Time-out for External FWD Call # 69 + PW + 050 + Digit (01-99) + *
7. Auto Attendant Ring Time-out # 69 + PW + 051 + Digit (05-30) + *
8. Time-out for JUN-JUN # 69 + PW + 052 + Digit (01-99) + *
Transferred Call
9. Hyper/CTI Port Selection : #69 + PW + 170 + Digit ( 0 – COM1/ 1 – COM2 ) N.A.
Only for CPU w/o Printer +*
10 “Transferred Call” Recall time # 69 + PW + 105 + Digit (15-60 ) + * set trfrecall < Time 15-60 Sec >
11 Waiting Tone & ‘Transfer to OPR’ #69+PW+ Prg.code 107 + < Digit 0 – Active / 1 - set oprxfrann <Digit:1=on/ 0=off>
MSG during Auto Atendant Inactive > + *
12 Waiting timeout during Auto #69+PW+ Prg.code 108 + <Duration> + * set waittime <Time(sec):1-5>
Attendant after Message. Duration : 1-5 Sec.
13 Programmable Billed Ext. #69 + PW + 110 + < 0 - X'ferring/ 1 - X'ferred ext set billext <Digit:0-X'ferring,1-
>+* X'ferred ext>
XXII. – Administrator Programming( Confidential)
1 Create Backup #69 +PW + 026 + 0 + * N. A.
2 Recover Backup #69 +PW + 027 + 0 + * Set recbackup
3 Create Master Backup #69 +PW + 181 + 0 + * N. A.
4 Recover Master Backup #69 +PW + 182 + 0 + * Set recmaster
------------------------------------------------------------------------------------------------------------------------------------------------------------------ 7
PROGRAMMING MANUAL Wednesday ,May 05, 2014
5 Set Printer Password #69 +PW + 030 + Printer PW + * N. A.
Set extname <extno> <name: max 20
6 Set Extension Name N.A.
characters>
7 Clear Ext Name N. A. Clear Extname < Ext No>
Set hotelname <word1><word2>
8 Set Hotel Name N. A.
<word3><word4>
Change Login PW for Hyper
9 N.A. Set newpw
Terminal
XXIII. – Voice Mail Programming
1 Program Extension as VoiceMail # 69 + PW + 053 + Ext. No + Digit + * Set voicemail <Ext No> <digit>
Extensions Digit : = 0 – Normal Ext ; =1 : Voicemail Port
2 Select Voice Mail Mode # 69 + PW + 054 + Digit + *
Digit : = 0 – disable
N. A.
1 – VM1 (Synectic)
2 – VM2 (Voice Gate)
XXIV. – Hotel Version Programming
#69 +PW + 301 + 1st Floor RS Ext + * + 2nd Floor
1 Floor-wise room Service Set roomserv <ext no : max 7 ext>
RS Ext + * + ……. ( Max 7 Floors)
#69 +PW + 302 + Single Access Digit (2-7) +
Single Digit Number Access
2 Department Ext. No + * + Single Access Digit (2- Set onedigacc <digit;2-7> <ext>
system
7) + Department Ext No + * + …..
Set roombarr <ext><digit: 0-Disable/
3 Room to Room Barring #69 +PW + 303 +Ext No + Func (0/1) + *
1- Enable>
4 Check-in #69 +PW + 304 + Ext No. + * Set checkin <extno>
#69 +PW + 305 + Ext No + Digit ( 0-Hyper/1-
5 Check-out Set checkout <ext>
Printer) + *
#69 +PW + 306 + Ext No + Digit ( 0-Temp Set tempinout <ext> <Digit: 0-
6 Temporary Check-in/Check-out
Checkout / 1- Temp Check-in) + * checkout/ 1- Checkin>
#69 +PW + 307 + Digit ( 0-Normal DT/ 1- Msg.
7 Dial Tone For Hotel Rooms N. A.
DT) + *
Programming MoH Prior to Dial #69+ PW + 106 + Digit ( 0 – Disable /1 – Enable)
8. set playmusic <digit:0=off / 1=on>
Tone Message +*
Room to Room calling – Set roomgrpext <Ext No> (Max 15
8 #69 + PW + 308 + Ext No + * + Ext No + * +….
Groupwise per group)
Removal of Ext. from Group
9 #69 + PW + 309 + Ext No + * Clear roomgrpext <Ext No>
Calling ( Room to Room)
#69+ PW + 310 + <EXT.NO.> + * + <1: Room
rent> + Amount (Rs xx-xxxxx.xx)+ * +
<2: Food>+ Amount (Rs xx-xxxxx.xx) +* + Set hotelbill <Ext.no> <Digit1-5>
10 Room Bill Entry
<3: Laundry>+ Amount (Rs xx-xxxxx.xx) +*+ <Amount (Rs.xx-xxxxx.xx)>
<4: Misc>+ Amount (Rs xx-xxxxx.xx) +* +
<5: Tax>+ Amount (Rs xx-xxxxx.xx) +*
#69 + PW + 311 + Digit 1/0> + * ( Digit: 0-
11 Room to Room Calling - Global set roomcall <Digit 0/1>
Disable, 1-Enable)
Clear Floorwise Room Service #69 +PW +Program code 312 + <Floor No: 1-
12 Clear roomserv <Floor No: 1-7>
Extensions 7> + *
#69 +PW +Program code 313 + <Digit: 2-7> +
13 Clear single digit Access Code Clear onedigacc <Digit: 2-7>
*

------------------------------------------------------------------------------------------------------------------------------------------------------------------ 8
PROGRAMMING MANUAL Wednesday ,May 05, 2014
CARD CODES
1 – EXT 8 10 – BRI JUN4-KTS4
2 – EXT 4 JUN 4 / JUN 4 11 – BRI KTS4-JUN4
3 - E1 MASTER 12 – BRI JUN 8
4 – E1 SLAVE 14 - EXT 6 JUN 2
CARD CODES
5 – PRI MASTER 15 – SLT 16 Plain
( Note : Digit 13 is not used )
6 – PRI SLAVE 16 – JLC 4X8
7 – EXT 16 (DuSlic) / SLT 16 Dx 17 – GSM 4P
8 – JUN 8 18 – VOIP SIP TRUNK
9 – BRI KTS 8 19 – VOIP TIE JUNCTION
CALLING PARTY NUMBER INFORMATION
TType of Number Numbering plan
1 Unknown 1 Unknown
2 International Number 2 ISDN/Telephony Numbering Plan
3 National Number 3 Data Numbering Plan
4 Network Specific Number 4 Telex Numbering Plan
5 Subscriber Number 5 National Standard Numbering Plan
6 Abbreviated NUmber 6 Private Numbering Plan
7 Reserved for Extensions

SOME IMPORTANT USER CODES


0 – Own MSN CLI
1 MSN DISPLAY #506 + Digit (0-2) 1 – Other Port MSN CLI
2 – Pilot No. display
Enable / Disable External Call
2 Forward feature for an Individual # 510 + User PW + Digit (0 – Disable / 1-Enable )
Ext.
Setting up Telephone Number # 511 + Telephone No. (including STD code if required)
3
for the I/C calls forwarded to +*
4. Enable Mobile Extension #512 + PW + Digit (1/0)
5. Extended Abbr. Dialing Access # 4 <000-499>
USER CODES for VOICE MAIL Programming
Off Hook Message Alert On/Off # 673 + PW + Digit <0 – OFF / 1 – ON>

Message Waiting String for SYNEGTIC / Voice Gate Voicemail


Message wait (Music) ON for
#591 + Ext
Ext.
Message wait (Music) ON for
# 590 +Ext
Ext.

In-band string for SYNECTIC Voice Mail


Call FWD on busy to VM 1 + Ext
Call FWD on No Reply /
2 + Ext
Unconditional. FWD to VM
In-band string for VOICE GATE Voice Mail
Ext. directly calling VM * 600 + Ext
Ext/JUN call FWD on Busy to VM * 500 + Ext
EXT./Jun call FWD on No Reply /
* 501 + Ext
Unconditional FWD to VM

------------------------------------------------------------------------------------------------------------------------------------------------------------------ 9
PROGRAMMING MANUAL Wednesday ,May 05, 2014
ANNEXURE
FEATURE CODE

Feat Dial Feat Dial


No. Code Description No. Code Description
000 #680 Change ext.password 030 #62 Other park pickup
001 #687 Change COS 031 #610 Unconditional forwarding
002 #677 Reset COS 032 #611 Forward on busy
003 #69 System programming 033 #612 Forward on no reply
004 #65 Printing commands 034 #671 Cancel internal forward
005 #607 DOSA class 035 #613 Budget bill announcement
006 #682 Set DND 036 #64 Pick any ext
007 #670 Set forward 037 #504 MSN landing
008 #602 Set hotline 038 #505 CLI landing
009 #603 Reset hotline 039 #600 Follow me
010 #683 Set Dynamic lock 040 #1 Pickup
011 #7 Dial abbreviated no. 041 0 Local jun seize
012 #502 CLIR 042 #4 Extended abbreviated dialling
013 #8 Selective jun seize 043 9 Operator dial
014 #2 Tie seize 044 #599 Reset port
015 #3 Selective tie seize 045 #506 Display MSNCLI
016 #674 Cancel ACB 046 #511 Set external forward
017 #685 Set self alarm 047 #510 Enable external forward
018 #686 Set others alarm 048 #673 Off hook msg
019 #675 Clear self alarm 049 #591 Enable voice mail waiting
020 #676 Clear others alarm 050 #590 Disable voice mail waiting
021 #501 Call monitoring 051 #512 Mobile ext
022 #615 Temporary walkin 052 #660 Invoke multiparty conference
023 #616 Long walkin 053 #661 Start multipaty conference
024 #617 Cancel walkin 054 #662 Delete multiparty conference
025 #614 Enable walkin 055 8 STD jun seize
026 #503 Room monitoring 056 * Redial
027 ##0 Set program password 057 #663 Port dial code announcement
028 #672 Set internal DND 058 #664 Feat dial code announcement
029 #63 Park pickup

Ports No. specified for Feature Code are virtual ports and has no concern with the Port No.
of the Extension generally referred to while programming MSN No. or Defining Ext. No. with
Add Port Program.

------------------------------------------------------------------------------------------------------------------------------------------------------------------ 10
PROGRAMMING MANUAL Wednesday ,May 05, 2014
DIAL CODE

Port Code Type Port Code Type Port Code Type


001 202 EXT 002 203 EXT 003 204 EXT
004 205 EXT 005 206 EXT 006 207 EXT
007 208 EXT 008 209 EXT 009
010 011 012
013 014 015
016 017 000 JUN 018 001 JUN
019 002 JUN 020 003 JUN 021 004 JUN
022 005 JUN 023 006 JUN 024 007 JUN
025 026 027
: : : : : : : : :
: : : : : : : : :
: : : : : : : : :
253 254 255
256 257 200 EXT 258 201 EXT
259 Invalid 260 Invalid 261 Invalid
262 Invalid 263 Invalid 264 Invalid
265 Invalid 266 Invalid 267 Invalid
268 Invalid 269 Invalid 270 Invalid
271 Invalid 272 Invalid 273 Invalid
274 Invalid 275 Invalid 276 681 EXT
277 682 EXT 278 683 EXT 279 684 EXT
280 685 EXT 281 686 EXT 282 687 EXT
283 688 EXT 284 689 EXT 285 690 EXT
286 Invalid 287 Invalid 288 Invalid
289 Invalid 290 Invalid 291 Invalid

Port No. specified for DIAL Code are the physical port of Ext / JUN as seen considering the
location of the ext. on the card and placement of the card in the system.

NOTE : If the system is operated in 8S mode, ports that can be set for Ext./JUN are from 001
through 160. 161 & 162 being KTS ports.
Ports for Hunt Groups viz 276 – 285 remain constant.

------------------------------------------------------------------------------------------------------------------------------------------------------------------ 11
PROGRAMMING MANUAL Wednesday ,May 05, 2014
PORT DETAILS SLOT-WISE FOR DIAL CODE

Slot No. Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 6 Slot 7 Slot 8

Port No.
KTS1- 129 001 017 033 049 065 081 097 113
KTS2-130 002 018 034 050 066 082 098 114
003 019 035 051 067 083 099 115
KTS1- 161 004 020 036 052 068 084 100 116
KTS2- 162 005 021 037 053 069 085 101 117
006 022 038 054 070 086 102 118
KTS1- 257 007 023 039 055 071 087 103 119
KTS2-258 008 024 040 056 072 088 104 120
009 025 041 057 073 089 105 121
010 026 042 058 074 090 106 122
011 027 043 059 075 091 107 123
012 028 044 060 076 092 108 124
013 029 045 061 077 093 109 125
014 030 046 062 078 094 110 126
015 031 047 063 079 095 111 127
016 032 048 064 080 096 112 128

Slot No. Slot 9 Slot Slot Slot 12 Slot Slot Slot Slot
10 11 13 14 15 16
Port No.
First Port 129 145 161 177 193 209 225 241
130 146 162 178 194 210 226 242

| | | | | | | |
| | | | | | | |
| | | | | | | |
V V V V V V V V

143 159 175 191 207 223 239 255


144 160 176 192 208 224 240 256
Last Port

CONNECTION DETAILS OF CABLES USED WITH NEOS

 The cable colour codes for JLCC, LCC 8 and LCC 16 are as under

Port number Colour code


1 Blue-White
2 Orange – White
3 Green- White
4 Brown - White
5 Gray-White
6 Blue-Red
7 Orange-Red
8 Green-Red

When connected to the card the Blue-White wires will be seen on the lower side of the card.
------------------------------------------------------------------------------------------------------------------------------------------------------------------ 12
PROGRAMMING MANUAL Wednesday ,May 05, 2014
In case of the LCC 16 2 such cables are used. The lower connector caters to ports 1 to 8 and the upper
to ports 9 o 16.

 SERIAL PORT CABLE : The serial port cable is configured as follows

9 PIN D TYPE 9 PIN D TYPE MALE


FEMALE – PC SIDE – PBX SIDE
1,4, 6 SHORT
7,8 SHORT
2 3
3 2
5 5
9 NC

Serial port 1 is for programming the NEOS and connecting PMS software if required. Port 2 is for
connecting to CTI applications.
The cable length should not exceed 15 meters or 50 feet.

PRI STATUS INDICATIONS

LED Color of Healthy Status If not indicating


Location LED Status Represented Healthy status
LD1 OFF Card/CPU status Check Card Status
ON if Faulty.
LD2 ON Operational OK
LD3 OFF LoS PRI not connected /
Line not UP
LD4 OFF RAI Remote Alarm
Indication
LD5 OFF AIS

LD6 ON LAP D

LD7 ON NETWORK CLK Clock from Exchg.


Not getting received.

------------------ END OF DOCUMENT ---------------

------------------------------------------------------------------------------------------------------------------------------------------------------------------ 13
PROGRAMMING MANUAL Wednesday ,May 05, 2014

You might also like