1N5333B Series

Preferred Device

5 Watt Surmetic
40
Zener Voltage Regulators
This is a complete series of 5 Watt Zener diodes with tight limits and
better operating characteristics that reflect the superior capabilities of
silicon−oxide passivated junctions. All this in an axial lead,
transfer−molded plastic package that offers protection in all common http://onsemi.com
environmental conditions.

Features Cathode Anode

• Zener Voltage Range − 3.3 V to 200 V
• ESD Rating of Class 3 (>16 kV) per Human Body Model
• Surge Rating of up to 180 W @ 8.3 ms
• Maximum Limits Guaranteed on up to Six Electrical Parameters
• These devices are manufactured with a Pb−Free external lead
finish only*

Mechanical Characteristics AXIAL LEAD

CASE 17
CASE: Void free, transfer−molded, thermosetting plastic
PLASTIC
FINISH: All external surfaces are corrosion resistant and leads are
readily solderable
MAXIMUM LEAD TEMPERATURE FOR SOLDERING PURPOSES:
MARKING DIAGRAM
230°C, 1/16 in. from the case for 10 seconds
POLARITY: Cathode indicated by polarity band
MOUNTING POSITION: Any L
1N
53xxB
YWW
MAXIMUM RATINGS
Rating Symbol Value Unit
L = Assembly Location
Max. Steady State Power Dissipation PD 5 W 1N53xxB = Device Code
@ TL = 75°C, Lead Length = 3/8 in = (See Table Next Page)
Derate above 75°C 40 mW/°C Y = Year
WW = Work Week
Operating and Storage TJ, Tstg −65 to °C
Temperature Range +200
Maximum ratings are those values beyond which device damage can occur. ORDERING INFORMATION
Maximum ratings applied to the device are individual stress limit values (not
normal operating conditions) and are not valid simultaneously. If these limits Device Package Shipping†
are exceeded, device functional operation is not implied, damage may occur
and reliability may be affected. 1N53xxB Axial Lead 1000 Units/Box

1N53xxBRL Axial Lead 4000/Tape & Reel

1N53xxBTA* Axial Lead 2000/Ammo Pack

*1N5361B Not Available in 2000/Ammo Pack
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.

Preferred devices are recommended choices for future use

and best overall value.

*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.

 Semiconductor Components Industries, LLC, 2004 1 Publication Order Number:

December, 2004 − Rev. 4 1N5333B/D
 1N5333B Series

ELECTRICAL CHARACTERISTICS (TA = 25°C unless I

otherwise noted, VF = 1.2 V Max @ IF = 1.0 A for all types)
IF
Symbol Parameter
VZ Reverse Zener Voltage @ IZT
IZT Reverse Current
ZZT Maximum Zener Impedance @ IZT
VZ VR V
IZK Reverse Current IR VF
IZT
ZZK Maximum Zener Impedance @ IZK
IR Reverse Leakage Current @ VR
VR Breakdown Voltage
IF Forward Current
VF Forward Voltage @ IF
Zener Voltage Regulator
IR Maximum Surge Current @ TA = 25°C

VZ Reverse Zener Voltage Change
IZM Maximum DC Zener Current

http://onsemi.com
2
 1N5333B Series

ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted, VF = 1.2 V Max @ IF = 1.0 A for all types)

Leakage
Zener Voltage (Note 2) Zener Impedance (Note 2) Current
IR
VZ IZM
VZ (Volts) @ IZT ZZT @ IZT ZZK @ IZK IZK IR @ VR (Note 3) (Note 4) (Note 5)
Device Device
(Note 1) Marking Min Nom Max mA   mA A Max Volts A Volts mA
1N5333B 1N5333B 3.14 3.3 3.47 380 3 400 1 300 1 20 0.85 1440
1N5334B 1N5334B 3.42 3.6 3.78 350 2.5 500 1 150 1 18.7 0.8 1320
1N5335B 1N5335B 3.71 3.9 4.10 320 2 500 1 50 1 17.6 0.54 1220
1N5336B 1N5336B 4.09 4.3 4.52 290 2 500 1 10 1 16.4 0.49 1100
1N5337B 1N5337B 4.47 4.7 4.94 260 2 450 1 5 1 15.3 0.44 1010
1N5338B 1N5338B 4.85 5.1 5.36 240 1.5 400 1 1 1 14.4 0.39 930
1N5339B 1N5339B 5.32 5.6 5.88 220 1 400 1 1 2 13.4 0.25 865
1N5340B 1N5340B 5.70 6.0 6.30 200 1 300 1 1 3 12.7 0.19 790
1N5341B 1N5341B 5.89 6.2 6.51 200 1 200 1 1 3 12.4 0.1 765
1N5342B 1N5342B 6.46 6.8 7.14 175 1 200 1 10 5.2 11.5 0.15 700
1N5343B 1N5343B 7.13 7.5 7.88 175 1.5 200 1 10 5.7 10.7 0.15 630
1N5344B 1N5344B 7.79 8.2 8.61 150 1.5 200 1 10 6.2 10 0.2 580
1N5345B 1N5345B 8.27 8.7 9.14 150 2 200 1 10 6.6 9.5 0.2 545
1N5346B 1N5346B 8.65 9.1 9.56 150 2 150 1 7.5 6.9 9.2 0.22 520
1N5347B 1N5347B 9.50 10 10.5 125 2 125 1 5 7.6 8.6 0.22 475
1N5348B 1N5348B 10.45 11 11.55 125 2.5 125 1 5 8.4 8.0 0.25 430
1N5349B 1N5349B 11.4 12 12.6 100 2.5 125 1 2 9.1 7.5 0.25 395
1N5350B 1N5350B 12.35 13 13.65 100 2.5 100 1 1 9.9 7.0 0.25 365
1N5351B 1N5351B 13.3 14 14.7 100 2.5 75 1 1 10.6 6.7 0.25 340
1N5352B 1N5352B 14.25 15 15.75 75 2.5 75 1 1 11.5 6.3 0.25 315
1N5353B 1N5353B 15.2 16 16.8 75 2.5 75 1 1 12.2 6.0 0.3 295
1N5354B 1N5354B 16.15 17 17.85 70 2.5 75 1 0.5 12.9 5.8 0.35 280
1N5355B 1N5355B 17.1 18 18.9 65 2.5 75 1 0.5 13.7 5.5 0.4 264
1N5356B 1N5356B 18.05 19 19.95 65 3 75 1 0.5 14.4 5.3 0.4 250
1N5357B 1N5357B 19 20 21 65 3 75 1 0.5 15.2 5.1 0.4 237
1N5358B 1N5358B 20.9 22 23.1 50 3.5 75 1 0.5 16.7 4.7 0.45 216
1N5359B 1N5359B 22.8 24 25.2 50 3.5 100 1 0.5 18.2 4.4 0.55 198
1N5360B 1N5360B 23.75 25 26.25 50 4 110 1 0.5 19 4.3 0.55 190
1N5361B* 1N5361B 25.65 27 28.35 50 5 120 1 0.5 20.6 4.1 0.6 176
1N5362B 1N5362B 26.6 28 29.4 50 6 130 1 0.5 21.2 3.9 0.6 170
Devices listed in bold, italic are ON Semiconductor Preferred devices. Preferred devices are recommended choices for future use and best overall value.
1. TOLERANCE AND TYPE NUMBER DESIGNATION
The JEDEC type numbers shown indicate a tolerance of ±5%.
2. ZENER VOLTAGE (VZ) and IMPEDANCE (IZT and IZK)
Test conditions for zener voltage and impedance are as follows: IZ is applied 40 ±10 ms prior to reading. Mounting contacts are located 3/8″
to 1/2″ from the inside edge of mounting clips to the body of the diode (TA = 25°C +8°C, −2°C).
3. SURGE CURRENT (IR)
Surge current is specified as the maximum allowable peak, non−recurrent square−wave current with a pulse width, PW, of 8.3 ms. The data
given in Figure 5 may be used to find the maximum surge current for a square wave of any pulse width between 1 ms and 1000 ms by plotting
the applicable points on logarithmic paper. Examples of this, using the 3.3 V and 200 V zener are shown in Figure 6. Mounting contact located
as specified in Note 2 (TA = 25°C +8°C, −2°C).
4. VOLTAGE REGULATION (
VZ)
The conditions for voltage regulation are as follows: VZ measurements are made at 10% and then at 50% of the IZ max value listed in the
electrical characteristics table. The test current time duration for each VZ measurement is 40 ±10 ms. Mounting contact located as specified
in Note 2 (TA = 25°C +8°C, −2°C).
5. MAXIMUM REGULATOR CURRENT (IZM)
The maximum current shown is based on the maximum voltage of a 5% type unit, therefore, it applies only to the B−suffix device. The actual
IZM for any device may not exceed the value of 5 watts divided by the actual VZ of the device. TL = 75°C at 3/8″ maximum from the device
body.
*Not Available in the 2000/Ammo Pack.

http://onsemi.com
3
 1N5333B Series

ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted, VF = 1.2 V Max @ IF = 1.0 A for all types)

Leakage
Zener Voltage (Note 7) Zener Impedance (Note 7) Current
IR
VZ IZM
VZ (Volts) @ IZT ZZT @ IZT ZZK @ IZK IZK IR @ VR (Note 8) (Note 9) (Note 10)
Device Device
(Note 6) Marking Min Nom Max mA   mA A Max Volts A Volts mA
1N5363B 1N5363B 28.5 30 31.5 40 8 140 1 0.5 22.8 3.7 0.6 158
1N5364B 1N5364B 31.35 33 34.65 40 10 150 1 0.5 25.1 3.5 0.6 144
1N5365B 1N5365B 34.2 36 37.8 30 11 160 1 0.5 27.4 3.5 0.65 132
1N5366B 1N5366B 37.05 39 40.95 30 14 170 1 0.5 29.7 3.1 0.65 122
1N5367B 1N5367B 40.85 43 45.15 30 20 190 1 0.5 32.7 2.8 0.7 110
1N5368B 1N5368B 44.65 47 49.35 25 25 210 1 0.5 35.8 2.7 0.8 100
1N5369B 1N5369B 48.45 51 53.55 25 27 230 1 0.5 38.8 2.5 0.9 93
1N5370B 1N5370B 53.2 56 58.8 20 35 280 1 0.5 42.6 2.3 1.0 86
1N5371B 1N5371B 57 60 63 20 40 350 1 0.5 45.5 2.2 1.2 79
1N5372B 1N5372B 58.9 62 65.1 20 42 400 1 0.5 47.1 2.1 1.35 76
1N5373B 1N5373B 64.6 68 71.4 20 44 500 1 0.5 51.7 2.0 1.52 70
1N5374B 1N5374B 71.25 75 78.75 20 45 620 1 0.5 56 1.9 1.6 63
1N5375B 1N5375B 77.9 82 86.1 15 65 720 1 0.5 62.2 1.8 1.8 58
1N5376B 1N5376B 82.65 87 91.35 15 75 760 1 0.5 66 1.7 2.0 54.5
1N5377B 1N5377B 86.45 91 95.55 15 75 760 1 0.5 69.2 1.6 2.2 52.5
1N5378B 1N5378B 95 100 105 12 90 800 1 0.5 76 1.5 2.5 47.5
1N5379B 1N5379B 104.5 110 115.5 12 125 1000 1 0.5 83.6 1.4 2.5 43
1N5380B 1N5380B 114 120 126 10 170 1150 1 0.5 91.2 1.3 2.5 39.5
1N5381B 1N5381B 123.5 130 136.5 10 190 1250 1 0.5 98.8 1.2 2.5 36.6
1N5382B 1N5382B 133 140 147 8 230 1500 1 0.5 106 1.2 2.5 34
1N5383B 1N5383B 142.5 150 157.5 8 330 1500 1 0.5 114 1.1 3.0 31.6
1N5384B 1N5384B 152 160 168 8 350 1650 1 0.5 122 1.1 3.0 29.4
1N5385B 1N5385B 161.5 170 178.5 8 380 1750 1 0.5 129 1.0 3.0 28
1N5386B 1N5386B 171 180 189 5 430 1750 1 0.5 137 1.0 4.0 26.4
1N5387B 1N5387B 180.5 190 199.5 5 450 1850 1 0.5 144 0.9 5.0 25
1N5388B 1N5388B 190 200 210 5 480 1850 1 0.5 152 0.9 5.0 23.6
Devices listed in bold, italic are ON Semiconductor Preferred devices. Preferred devices are recommended choices for future use and best overall value.
6. TOLERANCE AND TYPE NUMBER DESIGNATION
The JEDEC type numbers shown indicate a tolerance of ±5%.
7. ZENER VOLTAGE (VZ) and IMPEDANCE (IZT and IZK)
Test conditions for zener voltage and impedance are as follows: IZ is applied 40 ±10 ms prior to reading. Mounting contacts are located 3/8″
to 1/2″ from the inside edge of mounting clips to the body of the diode (TA = 25°C +8°C, −2°C).
8. SURGE CURRENT (IR)
Surge current is specified as the maximum allowable peak, non−recurrent square−wave current with a pulse width, PW, of 8.3 ms. The data
given in Figure 5 may be used to find the maximum surge current for a square wave of any pulse width between 1 ms and 1000 ms by plotting
the applicable points on logarithmic paper. Examples of this, using the 3.3 V and 200 V zener are shown in Figure 6. Mounting contact located
as specified in Note 7 (TA = 25°C +8°C, −2°C).
9. VOLTAGE REGULATION (
VZ)
The conditions for voltage regulation are as follows: VZ measurements are made at 10% and then at 50% of the IZ max value listed in the
electrical characteristics table. The test current time duration for each VZ measurement is 40 ±10 ms. Mounting contact located as specified
in Note 7 (TA = 25°C +8°C, −2°C).
10. MAXIMUM REGULATOR CURRENT (IZM)
The maximum current shown is based on the maximum voltage of a 5% type unit, therefore, it applies only to the B−suffix device. The actual
IZM for any device may not exceed the value of 5 watts divided by the actual VZ of the device. TL = 75°C at 3/8″ maximum from the device
body.

http://onsemi.com
4
 1N5333B Series

θ JL, JUNCTION-TO-LEAD THERMAL RESISTANCE (°C/W)

40

30

20
L L

10
PRIMARY PATH OF
CONDUCTION IS THROUGH
THE CATHODE LEAD
0
0 0.2 0.4 0.6 0.8 1
L, LEAD LENGTH TO HEATSINK (INCH)

Figure 1. Typical Thermal Resistance

TEMPERATURE COEFFICIENTS

10 300
θVZ , TEMPERATURE COEFFICIENT

θVZ , TEMPERATURE COEFFICIENT

200
8
100
6
RANGE
(mV/°C) @ I ZT

(mV/°C) @ I ZT

50
4
30
2 20
RANGE
0 10
−2 5
3 4 5 6 7 8 9 10 0 20 40 60 80 100 120 140 160 180 200 220
VZ, ZENER VOLTAGE @ IZT (VOLTS) VZ, ZENER VOLTAGE @ IZT (VOLTS)

Figure 2. Temperature Coefficient-Range Figure 3. Temperature Coefficient-Range

for Units 3 to 10 Volts for Units 10 to 220 Volts

http://onsemi.com
5
 1N5333B Series

θ JL (t, D), TRANSIENT THERMAL RESISTANCE

20
D = 0.5
JUNCTION-TO-LEAD ( °C/W)
10
5 D = 0.2 PPK t1
D = 0.1 t2
2
D = 0.05
1 DUTY CYCLE, D = t1/t2
D = 0.01 NOTE: BELOW 0.1 SECOND, THERMAL SINGLE PULSE
TJL = JL(t)PPK
0.5 NOTE: RESPONSE CURVE IS APPLICABLE REPETITIVE PULSES
TJL = JL(t, D)PPK
NOTE: TO ANY LEAD LENGTH (L).
D=0
0.2
0.00 0.00 0.01 0.05 0.1 0.5 1 5 10 20 50 100
1 5 t, TIME (SECONDS)
Figure 4. Typical Thermal Response
L, Lead Length = 3/8 Inch

40 30
20
I r , PEAK SURGE CURRENT (AMPS)

20

I r , PEAK SURGE CURRENT (AMPS)

PW
=
1
ms* 10
10 VZ
=
3.3
V
PW
=
8.3
ms* 5
4
2
2

1 1

0.5
0.4 VZ
=
200
V
*SQUARE WAVE PW
=
100
ms*
0.2 0.2 PLOTTED FROM INFORMATION
PW
=
1000
ms* GIVEN IN FIGURE 5
0.1 0.1
3 4 6 8 10 20 30 40 60 80 100 200 1 10 100 1000
NOMINAL VZ (V) PW, PULSE WIDTH (ms)
Figure 5. Maximum Non-Repetitive Surge Current Figure 6. Peak Surge Current versus Pulse Width
versus Nominal Zener Voltage (See Note 3)
(See Note 3)

1000

T
=
25°C
T
=
25°C
1000 TC
=
25°C
100
I Z , ZENER CURRENT (mA)
I Z , ZENER CURRENT (mA)

100
10
10

1
1

0.1 0.1
1 2 3 4 5 6 7 8 9 10 10 20 30 40 50 60 70 80
VZ, ZENER VOLTAGE (VOLTS) VZ, ZENER VOLTAGE (VOLTS)

Figure 7. Zener Voltage versus Zener Current Figure 8. Zener Voltage versus Zener Current
VZ = 3.3 thru 10 Volts VZ = 11 thru 75 Volts

http://onsemi.com
6
 1N5333B Series

100

I Z , ZENER CURRENT (mA)

10

0.1
80 100 120 140 160 180 200 220
VZ, ZENER VOLTAGE (VOLTS)

Figure 9. Zener Voltage versus Zener Current

VZ = 82 thru 200 Volts

APPLICATION NOTE

Since the actual voltage available from a given Zener For worst-case design, using expected limits of IZ, limits
diode is temperature dependent, it is necessary to determine of PD and the extremes of TJ (
TJ) may be estimated.
junction temperature under any set of operating conditions Changes in voltage, VZ, can then be found from:
in order to calculate its value. The following procedure is
V = VZ
TJ
recommended:
Lead Temperature, TL, should be determined from: VZ, the Zener voltage temperature coefficient, is found
from Figures 2 and 3.
TL = LA PD + TA
Under high power-pulse operation, the Zener voltage will
LA is the lead-to-ambient thermal resistance and PD is the vary with time and may also be affected significantly by the
power dissipation. zener resistance. For best regulation, keep current
Junction Temperature, TJ, may be found from: excursions as low as possible.
TJ = TL +
TJL Data of Figure 4 should not be used to compute surge

TJL is the increase in junction temperature above the lead capability. Surge limitations are given in Figure 5. They are
temperature and may be found from Figure 4 for a train of lower than would be expected by considering only junction
power pulses or from Figure 1 for dc power. temperature, as current crowding effects cause temperatures
to be extremely high in small spots resulting in device

TJL = JL PD
degradation should the limits of Figure 5 be exceeded.

http://onsemi.com
7
 1N5333B Series

PACKAGE DIMENSIONS

AXIAL LEAD
CASE 17−02
ISSUE C

NOTES:
1. LEAD DIAMETER AND FINISH NOT CONTROLLED
WITHIN DIMENSION F.

B INCHES MILLIMETERS
DIM MIN MAX MIN MAX
A 0.330 0.350 8.38 8.89
D B 0.130 0.145 3.30 3.68
D 0.037 0.043 0.94 1.09
K F −−− 0.050 −−− 1.27
F K 1.000 1.250 25.40 31.75
2 STYLE 1:
PIN 1. ANODE
2. CATHODE
A

1
F
K

SURMETIC is a trademark of Semiconductor Components Industries, LLC (SCILLC).

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free ON Semiconductor Website: http://onsemi.com
Literature Distribution Center for ON Semiconductor USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Order Literature: http://www.onsemi.com/litorder
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 For additional information, please contact your
Email: [email protected] Phone: 81−3−5773−3850 local Sales Representative.

http://onsemi.com 1N5333B/D
8