MX/TG (B6) Fault Codes

MX Magnum Tractor (P.I.N. Z6RZ01001 and above) (B6)

TG Series Tractor (P.I.N. Z6RW01001 and above) (B6)

ENGINE 10 Error Text

111 Engine Controller Failure - Hardware Failure

115 Engine Speed Sensor signal is failed
122 Boost Pressure Sensor voltage is too high
123 Boost Pressure Sensor voltage is too low
124 Boost Pressure level has exceeded the warning limit.
131 Foot Throttle Position potentiometer voltage is too high
132 Foot Throttle Position potentiometer voltage is too low
135 Oil Pressure Sensor voltage is too high
141 Oil Pressure Sensor voltage is too low
143 Oil Pressure level has fallen below the warning limit.
144 Coolant Temperature Sensor voltage is too high
145 Coolant Temperature Sensor voltage is too low
146 Coolant Temperature level has exceeded the warning limit.
151 Coolant Temperature level has exceeded the warning limit.
153 Intake Manifold Temperature Sensor voltage is too high
154 Intake Manifold Temperature Sensor voltage is too low
155 Intake Manifold Temperature level has exceeded the warning limit.
187 Sensor Supply 2 Voltage is too low.
211 Communications problem with Armrest, Instrumentation, or Transmission Controllers
221 Ambient Air Pressure Sensor Voltage is too high
222 Ambient Air Pressure Sensor Voltage is too low
227 Sensor Supply 2 Voltage is too high.
234 Engine Speed has exceed the overspeed warning limit.
238 Sensor Supply 3 Voltage is too low.
249 Ambient Air Temperature Voltage is too high.
256 Ambient Air Temperature Voltage is too low.
271 Front Pumping Control Valve current is low during "click test" (open circuit)
272 Front Pumping Control Valve current is high (short circuit)
281 Front Pumping element is failed
322 Injector Solenoid Driver Cylinder 1 current is low or open circuit.
323 Injector Solenoid Driver Cylinder 5 current is low or open circuit.
324 Injector Solenoid Driver Cylinder 3 current is low or open circuit.
325 Injector Solenoid Driver Cylinder 6 current is low or open circuit.
331 Injector Solenoid Driver Cylinder 2 current is low or open circuit.
332 Injector Solenoid Driver Cylinder 4 current is low or open circuit.
334 Engine Coolant Temperature data invalid.
342 An incompatible calibration has been detected in the ECM.
343 Engine Controller Failure - Hardware Failure
351 Injector Power Supply Voltage is low.
352 5 Volt Sensor Supply voltage is too low
386 5 Volt Sensor Supply voltage is too high
415 Oil Pressure level has fallen below the very low warning limit.
418 Water in Fuel sensor (optional) indicates the water in the fuel filter needs to be drained.
428 Water in Fuel Sensor voltage is too high.
 MX/TG (B6) Fault Codes
MX Magnum Tractor (P.I.N. Z6RZ01001 and above) (B6)
TG Series Tractor (P.I.N. Z6RW01001 and above) (B6)

ENGINE 10 Error Text

429 Water in Fuel Sensor (optional) voltage is too low.
431 Foot Throttle Idle Validation Switches are both closed
432 Foot Throttle position potentiometer and switches disagree.
435 Oil Pressure data invalid
441 Battery Voltage is too Low (less than 6 volts)
442 Battery Voltage is too High
449 Fuel Pressure level has exceeded the warning limit.
451 Fuel Pressure Sensor voltage is too high
452 Fuel Pressure Sensor voltage is too low
488 Intake Manifold Temperature level has exceeded the warning limit.
527 Cab pressurization/Ether relay coil circuit shorted high or open
528 Auxiliary Alternate Torque Validation Switch data invalid.
529 Output B driver shorted high or open
553 Front fueling actuator overfueling
554 Injector Metering Rail 1 Pressure data invalid.
559 Front fueling actuator underfueling
689 Engine Crankshaft Speed/Position data invalid.
697 ECM Internal Air Temperature Sensor Circuit Voltage too high
698 Engine Controller internal temperature too low
731 Engine Speed / Position #2 - Mechanical misalignment.
757 Electronic Control Module data lost.
778 Engine Camshaft Speed / Position Sensor data invalid.
779 Auxiliary Equipment Sensor Input 3 Error.
1117 Battery voltage too low, or the controller was not allowed to power down correctly
1256 Control Module Identification Input State Error.
1257 Control Module Identification Input State Error.
2117 Supply Voltage to the accelerator pedal position sensor too high.
2186 Supply Voltage to the accelerator pedal position sensor too low.
2195 Auxiliary Equipment Sensor Input # 3 - Engine Protection Critical - Special Instructions.
2249 Injector Metering Rail 1 Fuel Pressure lower than commanded pressure.
2265 Electric Lift Pump for Engine Fuel Supply Voltage too high.
2266 Electric Lift Pump for Engine Fuel Supply Voltage too low.
2292 Fuel Inlet Meter Device higher than expected.
2293 Fuel Inlet Meter Device flow demand lower than expected.
2311 Electronic Fuel Injection Control Valve open or closed Circuit.
2321 Engine Crankshaft Speed / Position data invalid.
2322 Engine Camshaft Speed / Position Sensor data invalid.
2555 Intake Air Heater 1 Circuit Voltage too high.
2558 Auxiliary PWM Driver 1 Circuit Voltage too low.
2973 Intake Manifold 1 Pressure data invalid.
 MX/TG (B6) Fault Codes
MX Magnum Tractor (P.I.N. Z6RZ01001 and above) (B6)
TG Series Tractor (P.I.N. Z6RW01001 and above) (B6)

TRANS 3
11 Master Clutch Potentiometer Open Circuit or short to ground
12 Master Clutch Potentiometer Short to +12 Volts or short to 5 Vreff
24 None of the transmission clutches are calibrated
37 BOC switch open circuit or Neutral relay stuck open
38 Shuttled to reverse when no wheel speed signal was available
47 Clutch pedal bottom of clutch switch misadjusted
48 BOC switch or Neutral relay short circuit
49 Auto Guidance Isolation valve driver Fault
50 Park Brake is powered off when in park
51 FNRP pod indicates Forward or Reverse is on, when Park is on
52 Park Brake is stuck on when commanded off
53 5 volt reference voltage too high
54 5 volt reference voltage too low
59 FNRP pod in illogical state (two positions on at same time)
60 FNRP pod in illogical state (in no position)
66 FNRP Pod Forward switch is shorted to ground or open circuit
67 FNRP Pod Forward switch is shorted to power
68 FNRP Pod Reverse switch is shorted to ground or open circuit
69 FNRP Pod Reverse switch is shorted to power
70 Battery voltage is too low for clutch solenoid operation
72 Transmission Oil Temperature is above 122 deg. C
73 Software is out of the calibration mode and the park brake request is still active.
74 The park brake ON with gear is engaged - no park brake request from calibration.
77 No signal from wheel speed sensor
78 Transmission regulated pressure accumulator is discharged
79 Engine RPM from the alternator is measured too high
80 Wheel speed sensor is measured too high
81 Transmission clutches are slipping
82 Creep Clutch is not calibrated
83 Communications Lost with Engine Controller
103 Odd clutch solenoid or its wiring failed open or shorted to ground
104 Even clutch solenoid or its wiring failed open or shorted to ground
105 C1-2 clutch solenoid or its wiring failed open or shorted to ground
106 C3-4 clutch solenoid or its wiring failed open or shorted to ground
107 C5-6 clutch solenoid or its wiring failed open or shorted to ground
108 Master clutch solenoid or its wiring failed open or shorted to ground
109 Low range clutch solenoid or its wiring failed open or shorted to ground
110 Mid range clutch solenoid or its wiring failed open or shorted to ground
111 High range clutch solenoid or its wiring failed open or shorted to ground
112 Reverse clutch solenoid or its wiring failed open or shorted to ground
113 Creeper clutch solenoid or its wiring failed open or shorted to ground
114 Even clutch solenoid coil or its wiring shorted to power
115 Odd clutch solenoid coil or its wiring shorted to power
116 C1-2 clutch solenoid coil or its wiring shorted to power
117 C3-4 clutch solenoid coil or its wiring shorted to power
 MX/TG (B6) Fault Codes
MX Magnum Tractor (P.I.N. Z6RZ01001 and above) (B6)
TG Series Tractor (P.I.N. Z6RW01001 and above) (B6)

TRANS 3
118 C5-6 clutch solenoid coil or its wiring shorted to power
119 Master clutch solenoid coil or its wiring shorted to power
120 Low range clutch solenoid coil or its wiring shorted to power
121 Mid range clutch solenoid coil or its wiring shorted to power
122 High range clutch solenoid coil or its wiring shorted to power
123 Reverse clutch solenoid coil or its wiring shorted to power
124 Creeper clutch solenoid coil or its wiring shorted to power
125 Odd clutch is not calibrated
126 Even clutch is not calibrated
127 C1-2 clutch is not calibrated
128 C3-4 clutch is not calibrated
129 C5-6 clutch is not calibrated
130 Low range clutch is not calibrated
131 Mid range clutch is not calibrated
132 High range clutch is not calibrated
133 Reverse clutch is not calibrated
134 Master clutch is not calibrated
135 Communication lost with the armrest controller
136 Communication lost with the instrumentation controller
137 Front Suspension raise lock solenoid circuit shorted or open circuit
138 Front Suspension raise solenoid circuit shorted or open circuit
139 Front Suspension lower lock solenoid circuit shorted or open circuit
140 Front suspension position is above the expected absolute limit
141 Front suspension position is below the expected absolute limit
142 Front suspension travel range has not been calibrated
143 Front suspension position is above the upper suspension range
144 Front suspension position is below the lower suspension range
145 Front Suspension lower lock solenoid circuit shorted or open circuit
147 Regulated system pressure below 290 PSI
148 Backup alarm circuit shorted or open
 MX/TG (B6) Fault Codes
MX Magnum Tractor (P.I.N. Z6RZ01001 and above) (B6)
TG Series Tractor (P.I.N. Z6RW01001 and above) (B6)

ARM 5
19 Hand THROTTLE potentiometer is failed
29 Aux 1st remote valve LEVER potentiometer is failed
39 Aux 2nd remote valve LEVER potentiometer is failed
49 Aux 3rd remote valve LEVER potentiometer is failed
59 Aux 4th remote valve LEVER potentiometer is failed
69 HITCH POSITION command potentiometer is failed
79 HITCH LOAD command potentiometer is failed
89 Aux 1st remote valve FLOW potentiometer is failed
99 Aux 2nd remote valve FLOW potentiometer is failed
109 Aux 3rd remote valve FLOW potentiometer is failed
119 Aux 4th remote valve FLOW potentiometer is failed
129 Aux 5th remote valve FLOW potentiometer is failed
139 Aux remote valve TIMER potentiometer is failed
149 Hitch UPPER LIMIT potentiometer is failed
159 Hitch DROP RATE potentiometer is failed
169 Hitch TRAVEL potentiometer is failed
1029 Aux 5th remote valve control switch is failed
1039 PTO switch is failed
1049 Hitch UP/DOWN switch is failed
1059 Hitch SLIP switch is failed
1069 MFD switch is failed
1079 DIFF LOCK switch is failed
1089 Programmable UP/DOWN switch is failed.
1099 Aux remote valve LIMIT SET switch is failed
1109 Hand Throttle IDLE VALIDATION switch is failed
1119 RECORD/PLAY switch is failed
1129 Invalid Configuration - Implement Depth Control switch is failed
1139 Engine Brake switch is failed
8011 Battery Voltage is too Low
9011 Controller Memory Error - Loss of Hitch Position Command Calibration
9012 Controller Memory Error - Loss of Aux Remote Lever Calibrations
9013 Controller Memory Error - Loss of Throttle Calibrations
9014 Controller Memory Error - Loss of MFD switch Configuration
9015 Controller Memory Error - Loss of Trans switches Configuration
9021 Hitch position command potentiometer calibration results not acceptable
9031 Hand throttle potentiometer calibration results not acceptable
9041 Hitch DROP RATE potentiometer calibration value(s) are out of range
10091 Armrest Controller failure - 5 V regulator failure
12013 Communications Lost with Data Bus and ALL other controllers

12081 Loss of/unavailable Performance Monitor Display - RECORD/PLAY functionality disabled

 MX/TG (B6) Fault Codes
MX Magnum Tractor (P.I.N. Z6RZ01001 and above) (B6)
TG Series Tractor (P.I.N. Z6RW01001 and above) (B6)

TMF 7 Tractor Multi-Function

2 Hitch Raise Solenoid Shorted to 12 volts.
3 Hitch Raise Solenoid High Side Driver shorted to 12 volts.
4 Hitch Raise Solenoid Failed Open or Shorted to Ground.
5 Hitch Lower Solenoid Shorted to 12 volts.
7 Hitch Raise/Lower Solenoids Open or short to ground.
11 Communications Lost with Data Bus and ALL other controllers
12 Communication lost with the armrest controller
14 5 Volt Sensor Supply voltage is too high
15 5 Volt Sensor Supply voltage is too low
17 Hitch Position Command potentiometer failed in the Armrest controller
18 Hitch Rockshaft Position potentiometer is outside normal operating range.
19 Hitch Upper Limit potentiometer is failed in the Armrest Controller
21 Hitch Load Command potentiometer is failed in the Armrest Controller
22 Single draft pin sensor failed when configured for one draft pin sensor.
23 Two draft pin sensors failed when configured for two draft pins.
24 Communications Lost with Instrumentation Controller
25 Hitch Up/Down Switch failed in the Armrest controller
26 Fender UP and DOWN switch failure or both switches simultaneously pressed
28 Hitch Travel potentiometer is failed in the Armrest Controller
29 Hitch Drop Rate potentiometer is failed in the Armrest Controller
30 Right Draft Pin voltage is outside the normal operating range.
31 Left Draft Pin voltage is outside the normal operating range.
32 Ground Speed Signal is failed in the Instrumentation Controller
33 Hitch Slip Set Switch failed in the Armrest controller
34 Hitch Slip Select Switch failed in the Armrest controller
35 Slip Sensor (radar or wheel speed) is failed in the Instrumentation Controller
37 The ARU reports EDC Transport Lock is faulty or not available.
41 Draft pin(s) detected but the Armrest controller specified tractor without draft control.
42 Engine speed must be set above 1600 rpm during calibration of lower valve.
43 No Draft pin(s) detected but the Armrest controller specified tractor with draft control.
44 Hitch calibration aborted due to tractor movement.

45 Hitch calibration attempted when the engine is not running or engine speed signal is failed.
47 Raise Valve calibration value is too high. (valve problem)
48 Raise Valve calibration value is too low. (valve problem)
50 Hitch position at top of travel is not within specification during calibration
51 Lower Valve calibration value is too high. (valve problem)
52 Lower Valve calibration value is too low. (valve problem)
53 The time allowed for hitch calibration has expired
54 Hitch position at bottom of travel is not within specification during calibration
55 Hitch position range from top to bottom is not within spec during calibration

56 Hitch position range to position command range ratio is not within spec during calibration.
57 Right Draft Pin voltage is not within spec for 'no load' condition during calibration
58 Left Draft Pin voltage is not within spec for 'no load' condition during calibration
 MX/TG (B6) Fault Codes
MX Magnum Tractor (P.I.N. Z6RZ01001 and above) (B6)
TG Series Tractor (P.I.N. Z6RW01001 and above) (B6)

TMF 7 Tractor Multi-Function

59 Both Draft Pin voltages are not within spec for 'no load' condition during calibration
60 Draft pin connected to left vs right for single pin setup during calibration
61 The Hitch Calibration procedure must be performed.
62 Communications Lost with Performance Monitor Function
63 Controller 8 volt reference is too high (above 8.8 volts).
64 Controller 8 volt reference is too low (below 7.2 volts).
65 Battery Voltage is too Low
66 Battery Voltage is too Low
80 MFD fault condition in software.
81 MFD Solenoid is failed Open or Short Circuit
82 Differential Lock Solenoid is failed Open or Short Circuit
83 Brake Lamp Relay Solenoid is failed Open or Short Circuit
86 Wheel Slip Signal is failed in the Instrumentation Controller
87 Ground Speed Signal is failed in the Instrumentation Controller
88 Differential Lock Switch is failed in the Armrest Controller
89 Differential Lock Switch is failed in the Armrest Controller
90 Differential Lock Switch is failed in the Armrest Controller
92 MFD Switch is failed in the Armrest Controller
93 MFD Switch is failed in the Armrest Controller
94 Differential Lockout fault condition in software.
98 Battery Voltage is too Low
99 Battery Voltage is too Low
106 Aux 5th remote valve control switch (Extend) is failed in the Armrest Controller
107 Aux 5th remote valve control switch (Retract) is failed in the Armrest Controller
108 Aux 1st remote valve LEVER potentiometer is failed in the Armrest Controller
109 Aux 2nd remote valve LEVER potentiometer is failed in the Armrest Controller
110 Aux 3rd remote valve LEVER potentiometer is failed in the Armrest Controller
111 Aux 4th remote valve LEVER potentiometer is failed in the Armrest Controller
112 Aux 1st remote valve FLOW potentiometer is failed in the Armrest Controller
113 Aux 2nd remote valve FLOW potentiometer is failed in the Armrest Controller
114 Aux 3rd remote valve FLOW potentiometer is failed in the Armrest Controller
115 Aux 4th remote valve FLOW potentiometer is failed in the Armrest Controller
116 Aux 5th remote valve FLOW potentiometer is failed in the Armrest Controller
120 Electro Hydraulic Remote top link switch is stuck on.
123 Aux 1st Lower Coil solenoid shorted to 12 volts.
124 Aux 1st Lower solenoid failed open or short circuit.
125 Aux 1st Raise Coil solenoid shorted to 12 volts.
126 Aux 1st Raise solenoid failed open or short circuit.
127 Aux 2nd Lower Coil solenoid shorted to 12 volts.
128 Aux 2nd Lower solenoid failed open or short circuit.
129 Aux 2nd Raise Coil solenoid shorted to 12 volts.
130 Aux 2nd Raise solenoid failed open or short circuit.
131 Aux 3rd Lower Coil solenoid shorted to 12 volts.
132 Aux 3rd Lower solenoid failed open or short circuit.
133 Aux 3rd Raise Coil solenoid shorted to 12 volts.
 MX/TG (B6) Fault Codes
MX Magnum Tractor (P.I.N. Z6RZ01001 and above) (B6)
TG Series Tractor (P.I.N. Z6RW01001 and above) (B6)

TMF 7 Tractor Multi-Function

134 Aux 3rd Raise solenoid failed open or short circuit.
135 Aux 4th Lower Coil solenoid shorted to 12 volts.
136 Aux 4th Lower solenoid failed open or short circuit.
137 Aux 4th Raise Coil solenoid shorted to 12 volts.
138 Aux 4th Raise solenoid failed open or short circuit.
139 Aux 5th Lower Coil solenoid shorted to 12 volts.
140 Aux 5th Lower solenoid failed open or short circuit.
141 Aux 5th Raise Coil solenoid shorted to 12 volts.
142 Aux 5th Raise solenoid failed open or short circuit.
147 Implement feedback #1 out of range High
148 Implement feedback #1 out of range Low
149 Implement feedback #2 out of range High
150 Implement feedback #2 out of range Low
151 Communications Lost with Transmission Controller
152 Electro Hydraulic Remote top link switch voltage is short circuit.
153 Electro Hydraulic Remote top link switch data invalid
154 PTO switch interlock - Cab Switch and Fender switch on at the same time.
155 Auto PTO switch data failed in the Armrest controller.
156 Auto PTO switch stuck ON in Armrest Controller.
157 PTO remote fender switch short circuit.
158 PTO remote fender switch open circuit
159 PTO remote fender switch stuck ON.
160 PTO Clutch is Slipping Too Much
161 PTO Shaft Overspeed Detected
162 Engine Stalled when the PTO was running.
163 PTO Shaft rotation is detected when the PTO clutch is OFF.
164 PTO shaft speed has not been detected within 3.6 seconds of being turned ON.
165 PTO Shaft rotation is detected when the Engine is OFF.
166 PTO Driver is on and no current is sensed.
167 Current sensed when the PTO driver is off.
168 PTO ON/OFF switch is failed in the Armrest Controller
169 PTO ON/OFF switch is failed in the Armrest Controller
170 PTO ON/OFF switch is failed in the Armrest Controller
171 PTO software fault condition detected.
172 PTO Solenoid Circuit is failed shorted to 12 Volts when PTO is in the off state.
173 PTO Solenoid Circuit is failed shorted to ground when PTO is in the off state.
174 Current flowing in the PTO sense resistor when the high side is off.
175 PTO Clutch has not reached lock up speed within 6 seconds of being turned ON
178 PTO speed sensor has been changed.
The PTO is receiving no frequency from the Shaft Size Sensor on a two speed PTO
179 configuration.
The PTO is receiving signals from the Shaft Size Sensor on a single speed PTO
180 configuration.
 MX/TG (B6) Fault Codes
MX Magnum Tractor (P.I.N. Z6RZ01001 and above) (B6)
TG Series Tractor (P.I.N. Z6RW01001 and above) (B6)

INST 23 TRACTOR MONITOR

1015 Seat Switch may be stuck closed.
3010 PTO Shaft Speed sensor is failed in PTO Controller
3020 Engine Speed sensor is failed in the Engine Controller
3022 Engine Overspeed Error
5010 Engine Oil Pressure sensor is failed in the Engine Controller
5011 Engine Oil Pressure sensor voltage is too low (open circuit, short to ground)
10031 Controller Memory Error - Loss of Engine Hours information
10032 Controller Memory Error - Loss of Vehicle Configuration information
10033 Controller Memory Error - Loss of Customer Configuration information
10034 Controller Memory Error: Loss of valid fuel table information.
10035 Controller Memory Error - Loss of Service information
10036 Controller Memory Error - Loss of Displayed Performance information
10037 Controller Memory Error - Loss of Implement Width information
10038 Controller Memory Error - Loss of Valid Remote Timer information.
11011 Fuel Level Sensor voltage is too low (open circuit, short to ground)
12011 Communications Lost with Armrest Controller
12021 Communications Lost with Auxiliary Controller
12031 Communications Lost with Hitch Controller
12043 Communications Lost with Data Bus and ALL other controllers
12051 Communications Lost with PTO Controller
12071 Communications Lost with Transmission Controller
12091 Communications Lost with Engine Controller
12101 Communications Lost with Tractor ECU (Gateway) Controller
12111 Communications Lost with Automatic Temperature Controller
13010 Engine Coolant Temperature sensor is failed in the Engine Controller
13011 Engine Coolant Temperature sensor voltage is too low (short to ground)
13012 Engine Coolant Temperature sensor voltage is too high (open circuit, short to +V)
13021 Transmission Oil Temperature sensor voltage is too low (short to ground)
13022 Transmission Oil Temperature sensor voltage is too high (open circuit, short to +V)
13031 Hydraulic Oil Temperature sensor voltage is too low (short to ground)
13032 Hydraulic Oil Temperature sensor voltage is too high (open circuit, short to +V)
13040 Air to Air Intake Temperature sensor is failed in the Engine Controller
13044 When fuel shut off relay is latched, short is detected (mechanical engine tractors only)
13051 Air to Air Intake Temperature sensor voltage is too low (short to ground)
13052 Air to Air Intake Temperature sensor voltage is too high (open circuit, short to +V)
53001 Instrumentation Controller Configuration is Incorrect
53002 Air to Air Intake sensor does not match Tractor Model Configuration
53005 Engine Shutdown activated by Instrument Controller
65535 NO ERROR. Errors have not been cleared from factory.
 MX/TG (B6) Fault Codes
MX Magnum Tractor (P.I.N. Z6RZ01001 and above) (B6)
TG Series Tractor (P.I.N. Z6RW01001 and above) (B6)

ATC 25 AUTOMATIC TEMPERATURE CONTROL

111 Cab sensor open or shorted to power
112 Cab sensor shorted to ground
115 Evaporator sensor open or shorted to power
116 Evaporator sensor shorted to ground
120 Blower speed select pot open/shorted to power
121 Temperature select pot open/shorted to power
125 High pressure switch (+) input shorted to power
126 High pressure switch (+) input shorted to ground
127 High pressure switch (-) input shorted to power
128 High pressure switch (-) input shorted to ground
129 High pressure cycling error (2 in 1 minute)
130 Low pressure switch (+) input shorted to power
131 Low pressure switch (+) input shorted to ground
132 Low pressure switch (-) input shorted to power
133 Low pressure switch (-) input shorted to ground
134 Low pressure switch open for > 1 minute