Lesson Plan in TLE Grade 10

Date: June 6, 2022

Time: 7:30- 9:00 AM
Subject Taught: TLE 10-ICT (Computer Systems Servicing)

I. Objectives:
At the end of the lesson, 85% of the Grade 10 learners must have:
a. identified materials necessary in assembling computer hardware;
b. assessed tools, equipment and testing devices needed for correct operation
and safety;
c. performed established procedures and systems requirements in
assembling/disassembling computer hardware.
II. Subject Matter:
a. Topic: Assembling/Disassembling Computer Hardware
b. Reference:
Monares, Acel S. (2020). TVL – Computer Systems Servicing Self-Learning
Module Grade 11 (First Edition). Department of Education – Division of General
Santos City Learning Resource Management System (LRMS).
c. Resources: System Units, Pictures, Laptop, LED Screen

III. Procedure:

Developmental Teacher’s Activity Student’s Activity

Activities
A. Preliminary
Activity
• Prayer Everyone is requested to stand for a - Classmates, let us pray
prayer.
- John, please lead the prayer
- Thank you John for the prayer
• Review
(Remember Me)
-System Case

-Motherboard

-Power Supply

• Motivation -DEVICE DRIVER

(Word Search -What words were formed after connecting -SCREW DRIVER
Puzzle) the texts in the grid? - PLIERS
-THERMAL PASTE
-POWER SUPPLY
-CONNECTOR
-CRIMPING TOOL
-LAN TESTER
-MULTI-TESTER
 -EYE WEAR

• Presentati -Today we are going to discuss about

on of the Lesson Assembling/Disassembling Computer
Hardware and Materials Needed in
Assembling/Disassembling Computer
Hardware
B. Activity Proper -This time you are going to find a partner - Students find each
for the activity. partner.
- Choose among you who will be the
person A and B. - 20 pairs of students in
total
Procedure:
1. Each pair will be given envelope; inside
the envelope are the steps in assembling
computer hardware and disassembling - Students open the
computer hardware. envelope and work
2. A sheet of paper will also be provided to together.
paste your work.
3. Person A will arrange the steps in
assembling computer hardware and paste
on the sheet of paper provided.
4. Person B will arrange the steps in
disassembling computer hardware and
paste on the sheet of paper provided.
5. All works will be posted on the board.
- Now we will compare your works and
check if who arranged the steps correctly.
- Students posted their
- Congratulations everyone who got a works on the board.
correct answer, those who are wrong you - Students compare and
still did a great job and better luck next check their work.
time.
- Thank you for your cooperation.

C. Analysis
C1. 1. Unplugging all the cables
Disassembling
Computer
Hardware
 2. Opening the outer shell/case

3. Removing the system fan

4. Removing the CPU fan

5. Detaching the power supply

6. Removing the CD / DVD Drives and

wires

7. Detaching the Hard Drive

8. Removing the Video Card

9. Removing the Memory (RAM)

10. Pull Out the Motherboard

C2. Assembling 1. Prepare your workplace

Computer
Hardware

2. Prepare the Motherboard

 3. Install the CPU

4. Install the CPU Heat Sink

5. Install Memory (RAM Modules)

6. Place the motherboard into the

case

7. Connect the Power Supply

8. Install Graphics / Video Cards

9. Install Internal Drives

10. Install the Add- in Cards

D. Abstraction -Guide Questions:

1. In disassembling and disassembling - That’s great Christian
computer hardware, which among because those are
of the materials are you commonly important and needed.
using?
2. What are system components that - Thank you Mary! It’s
you have disassembled and good to know that you
assembled? identified the components
you have disassembled
3. What are steps in disassembling and and assembled.
assembling computer hardware? - Very good Christian.
- Yes, those are the steps
in assembling and
disassembling computer
hardware. I hope that
you’ve learned that today.
E. Application -Now it’s time to form a group, let’s have
(Performance five groups. -1,2,3,4,5,1,2,3,4,5...
Task) - Please count off by five.
- Those who are in number 1 will be the -Group 1, Group 2,
Group 1, number 2 will be Group 2, Group3, Group 4, and
number 3 will be Group 3, number 4 will Group 5
be the Group 4 and number 5 will be the
Group 5.
- Each member should participate.

-Procedure:
-Given the necessary components,
materials, tools, equipment, and testing - Each group performed
devices, each group will perform the Task.
disassembling and assembling computer
hardware in Five (5) minutes. Safety
precautions must be observed when
working. You will be assessed in
accordance with the checklist provided
after the activity.

IV. Assessment:

Directions: Choose the letter that corresponds to your answer. Write your answer in a
separate sheet of paper.

1. In computer disassembly, which of the following should be done first?

a. Pull out the motherboard c. Unplug all the cables and wires
b. Open the computer case d. Prepare the system components

2. Which of the following should be done in the opening the outer shell or case?
a. Unplug all the cables and wires that are connected to the system unit.
b. Unplug the ribbon at the back of the drive.
c. Use a knife to immediately remove the side panels.
d. Remove the four screws from the computer's rear.

3. Test run is performed after the power has been connected to the motherboard in order to
_____________.
a. Verify that the installation was done correctly and that the motherboard was not
damaged.
 b. Change the time, date, and loading procedures.
c. identifying computer glitches
d. network configuration is carried out.

4. The majority of computers beep once upon startup to show that all hardware is
operational. You then boot your computer without hearing a beep. What should you examine
initially?
a. RAM b. System Board c. Speaker d. Microprocessor

5. It is important to perform proper disassembly of computer in order to ________.

a. prevent deletion of ROM BIOS program
b. stop the boot up process in the computer
c. protect the power supply of the computer
d. avoid damage of internal components of the computer

6. Prior to assembling a computer, what should you wear to protect computer parts from
Electrostatic Discharge (ESD)?
a. Gloves c. Protective Eyewear
b. Anti-static Wrist Strap d. Anti-Static Bag

7. Which of the following installation procedures for the CPU in the motherboard SHOULD
NOT be carried out?
a. Force the CPU on the socket.
b. To lock the CPU in place, push the rod downward.
c. Never take the CPU cover off. Once the CPU has been installed, it can be removed.
d. Make sure the CPU's pins are straight and in the right place on the socket before
inserting it in the slot.

8. Which of the following statement about computer assembly is TRUE?

a. Holding the Hard Disk Drive (HDD) at the bottom is the right way to handle it.
b. Make sure the CPU's pins are straight and in the right places before placing it in the slot.
c. Connect the power connector for the fan assembly to the heat sink.
d. After the drive bay's connections are connected, install the RAM.

9. Which of the following shows the correct steps in computer disassembly?

I. Detaching the Hard Drive
II. Detaching the power supply
III. Opening the outer shell / case
IV. Pull Out the Motherboard
V. Removing the CD / DVD Drives
VI. Removing the CPU fan
VII. Removing the Memory (RAM)
VIII. Removing the system fan
IX. Removing the Video Card
X. Unplugging all the cables

a. X,III,VIII,VI,II,V, I,VII,IX,IV c. III,VII, I,X,VI,V,II,IX,VIII,IV

b. I, VI, IX,VII, V, II, IV, III,VIII,IX d. IX, IV,II, V,I, IX,VII, VI,VIII,III
 10. Which of the following shows the correct steps in computer assembly?
I. Connect the Power Supply
II. Install Graphics / Video Cards
III. Install Internal Drives
IV. Install Memory (RAM Modules)
V. Install the Add- in Cards
VI. Install the CPU
VII. Install the CPU Heat Sink
VIII. Place the motherboard into the case
IX. Prepare the Motherboard
X. Prepare your workplace

a. X,VI,I,VII,V,II,IV,III,VIII,IX c. X,III,VIII, II,IX, VII, I,VI,V,IV

b. X, II,VII, IX,VIII,I,IV, V,III,VI d. X,IX,VI,VII,IV,VIII,I,II,III,V

V. Assignment:

Study in advance the portable bootable devices.

Prepared by:

GUILLER ANDREI C. COLOSO

BTLED ICT 3-A