05

SEMBCORP GAYATRI POWER LTD Document No

SGPL-CMP-001
SILICA ANALYZER CALIBRATION
Revision No. 00 Revision Date : 06-07-2017 Issue Date : 06-07-2017 No. of Pages: 1 of 5

CONTROLLED SOFT COPY

SMP FOR SILICA ANALYZER CALIBRATION

SGPL-CMP-001

 
  Prepared By Reviewed By Approved By
 
 
  Name: M.Rajesh Name: V. Venkata Krishna Sign:
  Dt: 29-06-2017 Dt: 01-07-2017 Dt: 04-07-2017
 
  Designation: (Engineer) Designation: Manager-C&I Designation: General Manager
 
 
 
 
 
 

Page 1 of 5
 
05

SEMBCORP GAYATRI POWER LTD Document No

SGPL-CMP-001
SILICA ANALYZER CALIBRATION
Revision No. 00 Revision Date : 06-07-2017 Issue Date : 06-07-2017 No. of Pages: 2 of 5

TABLE OF CONTENTS: 
 
 
 

PART NO:  DESCRIPTION  PAGE NO: 

1.0  PURPOSE  3 

2.0  SCOPE  3 

3.0  RESPONSIBILITY  3 

4.0  TOOLS REQUIREMENT  3 

5.0  SAFETY &ENVIRONMENTAL MEASURES  4 

6.0  PROCEDURE  4 

7.0  REFERENCE DOCUMENTS  5 

8.0  RECORD FORMATS  5 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
Page 2 of 5
05

SEMBCORP GAYATRI POWER LTD Document No

SGPL-CMP-001
SILICA ANALYZER CALIBRATION
Revision No. 00 Revision Date : 06-07-2017 Issue Date : 06-07-2017 No. of Pages: 3 of 5

1.0 Purpose:
This Procedure is intended to provide guidance and instructions for Carrying out the
Calibration Of Silica Analyzer.

2.0 Scope:
This procedure is applicable to Silica Analyzer 9610Sc.

3.0 Responsibility:

1. All the C&I personnel involved in carrying out /supervising the above activities are
required to ensure implementation of this procedure and may consult any other relevant
documents indicated under Reference section below.
2. In the event of any changes required in the procedure such changes may be requested
with HOD

4.0 T&P Required:

1. Multi meter.
2. Allen key.
3. T20 Screw Driver.
4. Screw Driver set.
5. Adjustable Spanner.
6. Tissue Paper.
7. Teflon Tape.

 
Page 3 of 5
05

SEMBCORP GAYATRI POWER LTD Document No

SGPL-CMP-001
SILICA ANALYZER CALIBRATION
Revision No. 00 Revision Date : 06-07-2017 Issue Date : 06-07-2017 No. of Pages: 4 of 5

5.0 Safety & Environmental measures / checks:

1. Ensure Adequate light in work area.
2. Ensure good housekeeping of the working area.
3. Protective eye wear & hand gloves is always recommended when contact with chemicals
is possible.
4. Minor injury / cuts while cleaning the analyzer.

6.0 Procedure:

1. At first take proper PTW as per SGPL PTW policy.

2. Calibration: The automatic calibration uses the installed known standards to calibrate
the analyzer. Calibration can be done manually or scheduled to occur automatically. Use the
calibration menu to view calibration data, start or cancel the auto calibration, override the
auto cal settings, calibrate manually or to reset to the default calibration.
3. Push cal to display the calibration menu. Option Description START MANUAL CAL Refer to
start a calibration manually.
4. SET AUTO CALIBRATION Refer to Schedule automatic calibration.
5. CALIBRATION DATA Displays data from the last calibration and the due date and time of the
next scheduled calibration.
6. OVERRIDE CALIBRATION Enter new slope and zero values and disables automatic calibration.
7. OUTPUT CALIBRATION Select a 4-20 mA output and enter the output values to be sent.
8. RESET DEFAULT CAL Reset calibration data to default values and disables automatic
calibration. On completion, perform a new calibration. Schedule automatic calibration.
1) Push cal, then select SET AUTO CALIBRATION.
2) Select ACTIVATE AUTO CAL>YES.
3) Select STD SOLUTION and enter the standard value in ppb.
4) Select a schedule option for calibration.

 
Page 4 of 5
05

SEMBCORP GAYATRI POWER LTD Document No

SGPL-CMP-001
SILICA ANALYZER CALIBRATION
Revision No. 00 Revision Date : 06-07-2017 Issue Date : 06-07-2017 No. of Pages: 5 of 5

9. Option Description TIME BASE sets the interval between calibrations.

10. Options: DAYS or HOURS. WEEK DAY selects the day or days of the week for calibration
when TIME BASE is set to DAY. TIME Sets the time of day for calibration when the TIME
BASE is set to DAY.
11. SET INTERVAL Sets the interval between automatic calibrations in hours when the TIME
BASE is set to HOURS.
12. Start a calibration manually.
1) Push cal, then select START MANUAL CAL.
2) The type of calibration is displayed. Push enter to start the calibration.
3) The measurement status is displayed. Select YES to interrupt the current
measurement cycle and start the calibration immediately Select NO to wait until the
current measurement cycle has completed before the calibration starts.

7.0 Reference:
Hach 9610Sc Silica Manual. (SGPL-CMP-001-F01)
HIRA: SGPL/MAINT/C&I/BTG-SWAS-006

 
Page 5 of 5