PDF Q0 Module 4 Carpentry 7 8

Download as pdf or txt
Download as pdf or txt
You are on page 1of 14

7/8

TLE-IA-CARPENTRY
Quarter 0 – Module 4
MAINTAIN TOOLS AND EQUIPMENT
(PERFORM BASIC PREVENTIVE
MAINTENANCE)
TLE-IA-Carpentry – Grade 7/8
Alternative Delivery Mode
Quarter 0 – Module 4: Maintain Tools and Equipment (Perform Basic Preventive
Maintenance)
First Edition, 2020

Republic Act 8293, section 176 states that: No copyright shall subsist in any
work of the Government of the Philippines. However, prior approval of the government
agency or office wherein the work is created shall be necessary for exploitation of such
work for profit. Such agency or office may, among other things, impose as a condition
the payment of royalties.

Borrowed materials (i.e., songs, stories, poems, pictures, photos, brand names,
trademarks, etc.) included in this module are owned by their respective copyright
holders. Every effort has been exerted to locate and seek permission to use these
materials from their respective copyright owners. The publisher and authors do not
represent nor claim ownership over them.

Published by the Department of Education


Secretary: Leonor Magtolis Briones
Undersecretary: Diosdado M. San Antonio

Development Team of the Module


Writer: Gray Hared Mae T. Iniego
Editors: Howel Jay M. Caluyo, John Paul Jeremiah B. Teves
Reviewers: Dennis S. Calinao, Gemuel C. Ibero, Howel Jay M. Caluyo, Alden B. Deguit,
John Paul Jeremiah B. Teves
Typesetter: Gray Hared Mae T. Iniego
Layout Artist: Alden B. Deguit
Management Team: Senen Priscillo P. Paulin, CESO V Rosela R. Abiera
Fay C. Luarez, TM, Ed.D., Ph.D. Maricel S. Rasid
Adolf P. Aguilar, Ed.D., TM Elmar L. Cabrera
Nilita R. Ragay, Ed.D.
Antonio B. Baguio Jr., Ed.D.

Printed in the Philippines by ________________________

Department of Education –Region VII Schools Division of Negros Oriental

Office Address: Kagawasan, Ave., Daro, Dumaguete City, Negros Oriental


Tele #: (035) 225 2376 / 541 1117
E-mail Address: negros.oriental@deped.gov.ph
7/8

TLE-IA-CARPENTRY
Quarter 0 – Module 4
MAINTAIN TOOLS AND
EQUIPMENT
(PERFORM BASIC PREVENTIVE
MAINTENANCE)
What I Need to Know

This module was designed and written with you in mind. It is here to help you master
the nature of Carpentry. The scope of this module permits it to be used in many
different learning situations. The language used recognizes the diverse vocabulary
level of students. The lessons are arranged to follow the standard sequence of the
course. But the order in which you read them can be changed to correspond with
the textbook you are now using.

The module is talking about this lesson:


• Lesson 1 – Maintain Tools and Equipment

After going through this module, you are expected to:


1. Repair defective tools used for basic maintenance.
2. Conduct preventive measures for the maintenance of carpentry.
3. Value the importance of tools and equipment

What I Know

Direction: Read each item carefully and use your notebook to write your answers.
As part of your initial activity, you will be challenged to dig deeper on your knowledge
and previous experiences on the topic. Try to diagnose or assess what you already
know about identifying materials and tools applicable to as specific construction job.
Take this test.

Instructions: Define the following


1. Tools 6. Inventory
2. Equipment 7. Label
3. Lubricate 8. Lubricants
4. Requisition 9. Perimeter
5. Grease 10. Power tools

1
Lesson
Maintain Tools and
1 Equipment

Line steel pipes are galvanized, giving the piping corrosion-resistant properties.
Standard steel pipes are fabricated to a diameter no greater than 16 inches,
according to steel pipes and tubing. Structural steel tubes are constructed into
either square or circular shapes. Plumbing tubes are often fabricated thinner than
other types of steel pipes to allow for easier soldering.

What’s In

Inventory – the accounting of tools and materials

Label – refers to the indicated name of tools and equipment

Segregate – set aside things from the others

Standard – serves as a measure of reference

Stock – refers to a lumber for a certain carpentry job Store – to put tools and
materials in their proper places

2
Notes to the Teacher
You may add your preferred activity as long as it is parallel
to the content of this module.

What’s New

Let us determine how much you already know about identifying materials and
tools applicable to a specific construction job

Identify the different tools and materials that are described in each item.

1. Tool used for smoothing curve surfaces.


2. Tool used for drawing arcs and circles.
3. Tool used for testing the squareness of large stocks.
4. Tool used to hold bits when boring.
5. Materials used to lubricate movable parts.
6. Tool used to cut stock along the grain.
7.Tool used for sharpening saws.
8. Used to drive and pull-out nails on wooden surfaces.
9. Made of wood or rubber used to drive other tools like chisel.
10. Used in setting the head of a finishing nail below the surface of the
wood.

3
What is It

Line steel pipes are galvanized, giving the piping corrosion-resistant properties.
Standard steel pipes are fabricated to a diameter no greater than 16 inches,
according to steel pipes and tubing. Structural steel tubes are constructed into
either square or circular shapes. Plumbing tubes are often fabricated thinner than
other types of steel pipes to allow for easier soldering.

PROPERTIES LUBRICATING TOOLS AND EQUIPMENT

1. Read and analyze the use of preventive Maintenance Schedule form.


2. Determine the types of tools and machine needed to be lubricated.
3. Fill out a requisition slip form in releasing the lubricants needed.
4. Secure a borrower’s slip from your teacher.
5. Fill out the slip form correctly intended for the needed tools.
6. Perform the task according to the prescribed schedule and the assigned
machine.
7. Perform lubricating procedure.
8. Determine the parts of the machine needed to be lubricated.
9. Apply thin coat of oil on the parts for a long period of time.
10. Open the bearing cover and apply grease.
11. Apply grease on sealed bearing with the use of a grease gun.

Steps in Filling Out Inspection Report Form

Directions: Do the following procedure.

1. Secure an inspection report form from your teacher.


2. Determine the defective instrument based on the report form.
3. Replace inspected tool and equipment defects based on the report form.
4. Use the Repair Manual in replacing the defective parts.

Line steel pipes are galvanized, giving the piping corrosion-resistant properties.
Standard steel pipes are fabricated to a diameter no greater than 16 inches,
according to steel pipes and tubing. Structural steel tubes are constructed into
either square or circular shapes. Plumbing tubes are often fabricated thinner than
other types of steel pipes to allow for easier soldering.

4
What’s More

Directions: Give the meaning of each word. Write this on your quiz notebook.
1. Sketch 6. Tools
2. Design 7. Equipment
3. Projections 8. Lubricate
4. Dimension 9. Requisition
5. Isometric 10. Grease

What I Have Learned

Directions: Copy the table on a separate sheet of paper then check the appropriate
box whether you performed each indicator.

INDICATORS YES NO
1. Utilized the Preventive Maintenance Schedule.
2. Determined the types of tools and machine needed to be lubricated
3. Filled out the requisition slip form in releasing the lubricants
needed.
4. Secured the borrower’s slip from your teacher?
5. Filled out the slip form correctly intended for the needed tools.
6. Performed the task according to the prescribed schedule and the
assigned machine.
7. Performed the lubricating procedures.
8. Determined the parts of the machine needed to be lubricated.
9. Applied the thin coat of oil on the parts that are used for a long
period of time.
10. Applied the grease on sealed bearing with the use of a grease gun.

5
What I Can Do

OPTIONAL ACTIVITY (To be performed during face-to-face classes).


Directions: Copy the table on a separate sheet of paper then check the appropriate
box whether you performed each indicator.

INDICATORS YES NO
1. Secured the inspection report from the teacher.
2. Determined defective instruments.
3. Inspected the defective tools.
4. Replaced the defective tools.
5. Used the Repair manual as guide in replacing defects.

SCORING GUIDE
7-8 VERY
SATISFACTORY
5-6 SATISFACTORY
4-3 FAIR
1-2 FAILED

Assessment

Answer this question and write it down in your activity notebook.

• Steps in Filling Out Inspection Report Form

6
Additional Activities

Copy and answer this in your activity notebook.

I have learned that ________________________________ ______.

I have realized that _________________________________ _____.

I will apply _____________

7
8
What I know
1. Tools a handheld device that aids in accomplishing a task
2. Equipment implements used in an operation or activity
3. Lubricants a substance capable of reducing friction heat and wear when introduced as
a film between solid surfaces.
4. Requisition the act of formally requiring or calling upon someone to perform an action
5. Grease a thick lubricant oily matter.
6. Inventory is the accounting of tools and materials
7. Label is referring to the indicated name of tools and equipment
8. Lubricants are oils or grease which is used to help the machine to run smoothly
9. Perimeter the bounding line or curve of a plain area
10.Power tools handy machines operated by current/electricity
Answer Key
9
What’s New
1. Spoke Shave
2. Sanding Sealer
3. Compass
4. Steel Square
5. Filler
6. Auger Brace
7. Lubricant
8. Claw Hammer
9. Mallet
10. Nail Set
What’s More
1. Sketch is a design toolkit built to help you create your best work from your
earliest ideas through to final artwork.
2. Design a plan or drawing produced to show the look and function of
workings of a building, garment, or other object before it is built or made.
3. Projections an estimate or forecast of a future situation or trend based on a
study of present ones.
4. Dimensions a measurement of the size of something in a particular direction
5. Isometric equality of measure.
6. Tools a handheld device that aids in accomplishing a task
7. Equipment implements used in an operation or activity
8. Lubricants a substance capable of reducing friction heat and wear when
introduced as a film between solid surfaces.
9. Requisition the act of formally requiring or calling upon someone to perform
an action
10.Grease a thick lubricant oily matter.
References
FELY L. MANUEL & ORLANDO E. MANUEL, Learning Module on Carpentry NC II
(Exploratory Course in Technology and Livelihood Education, Grade7 and Grade 8)

All pictures are taken from Learning Module on Carpentry NC II (Exploratory Course
in Technology and Livelihood Education, Grade 7 and Grade 8)
For inquiries or feedback, please write or call:

Department of Education – Schools Division of Negros Oriental


Kagawasan, Avenue, Daro, Dumaguete City, Negros Oriental

Tel #: (035) 225 2376 / 541 1117


Email Address: negros.oriental@deped.gov.ph
Website: lrmds.depednodis.net

You might also like