Scribd
Upload
56 views4 pages

TSC Tech Talk - Grounding

Improper grounding can create lethal hazards and is a common cause of hum in sound systems. A ground loop occurs when there are multiple ground connection paths between two pieces of equipment, forming a conductive loop that picks up interference. This interference travels along unintended paths, modulating signal voltages and causing hum and noise. To avoid ground loops, equipment can be grounded at a single central point, isolated from earth ground, or use transformers between components to block ground currents. However, safety grounds should never be removed, as this increases shock risks.

Uploaded by

Rnh Aco
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
56 views4 pages

TSC Tech Talk - Grounding

Improper grounding can create lethal hazards and is a common cause of hum in sound systems. A ground loop occurs when there are multiple ground connection paths between two pieces of equipment, forming a conductive loop that picks up interference. This interference travels along unintended paths, modulating signal voltages and causing hum and noise. To avoid ground loops, equipment can be grounded at a single central point, isolated from earth ground, or use transformers between components to block ground currents. However, safety grounds should never be removed, as this increases shock risks.

Uploaded by

Rnh Aco
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

TSC Tech Talk | Grounding

Improper grounding can create a lethal hazard. Even if you advert danger, ground loops are the most
common cause of AC line frequency hum in sound systems. So it pays to learn about grounding, and use
what you learn.

What is a ground loop?


A ground loop occurs when there is more than one ground connection path between two pieces od
equipment. The duplicate ground paths form the equivalent of a loop antenna which very efficiently
picks up interference currents. Lead resistance transforms these currents into voltage fluctuations. As a
consequence of ground loop induced voltages, the ground reference in the system is no longer a stable
potential, so signals ride on the noise.The noise becomes part of the program signal.

Can ground loops be eliminated?


Sometimes, in poorly designed sound equipment, ground loops occur inside the chassis. Even thought
the equipment has balanced inputs and outputs. In this instance, little can be done to get rid of hum.
You should avoid unbalanced equipment in your system. The exception to the rule would be with
equipment that will be very close together, connected to the same leg of the AC service.

Figure 1 illustrates a typical ground loop situation. Two interconnected pieces of equipment are plugged
into grounded AC outlets at separate locations, and the signal ground is connected to earth in each of
them. The earth ground path and duplicate signal ground path form a loop which can pick up

file:///F|/Books/grounding/TSC Tech Talk Grounding.htm (1 of 4)15/03/2007 10:02:21 •


TSC Tech Talk | Grounding

interference. If the equipment is not properly built, these circulating ground loop noise currents (which
act like signals) travel along paths not intended to carry signals. The currents, in turn, modulate the
potential of the signal carrying wires, producing hum and noise voltages that cannot easily be separated
from the program signals of the affected equipment. The noise is then amplified along with the program
signal.

What can you do to avoid ground loops?


There are four basic approaches to dealing with grounds within an audio system: single point, multiple
point, floating, and telescoping shield. Each has specific advantages in different types of systems.
Figure 2 illustrates single-point grounding. Chassis ground in each individual component is connected to
earth. The signal ground is carried between components and connected to earth at one central point. This
configuration is very effective in eliminating line frequency hum, but is easier to use in permanently
installed systems. Single point grounding is how TSC normally wires studios and is common practice in
most other studios as well. It is also effective in wiring individual racks for theatre and church installs.

Multiple point grounding (figure 3)is what you find with unbalanced equipment in whcih chassis
connect to signal ground. It is very simple in practice, but is not very reliable ... particularly is the
system configuration is changed frequently. A good example of multiple grounding would be a guitar
rack. One advantage to the rack system is that the chassis are on the same rack rails which in turn
referenced the whole rack as a single point ground.

file:///F|/Books/grounding/TSC Tech Talk Grounding.htm (2 of 4)15/03/2007 10:02:21 •


TSC Tech Talk | Grounding

Multiple point ground systems that employ balanced circuits with properly designed equipment present
no special noise problems.
Figure 4 shows the floating ground principle. Note that the ground in completely isolated from the earth.
This system is useful when the earth ground carries significant noise. It does, however, rely on the
equipment input stage to reject interference induced in cable shields, so the input amp better be good.

Figure 5 illsutrates the principle of telescoping shields. This scheme is very effective in eliminating
ground loops. When noise enters a shield connection only to earth, that noise can't enter the signal path.

Implementing this approach requires balanced lines and transformers since ground is not carried
between components. There is still debate about the use of transformers in modern audio equipment
though.

Grounding Safety
The main reason we ground a sound system is for safety. Proper grounding can prevent lethal shocks.
The next reason for grounding a system that includes AC powered equipment is that proper grounding
may reduce external noise pickup.
The AC power cord ground (the green wire and the third pin on the AC plug) connects the chassis of
electronic equipment to a wire in the wall power service that leads to an earth ground. The earth ground,
required by electrical codes everywhere, can contribute to ground loops.

Don't break the AC ground!!!


With just one path to ground, there can't be a ground loop. Can there be a ground loop with one audio
cable joining a console to a power amplifier? Yes! A ground connection through the AC cables and the
chassis of the two units campletes the second ground connection.

One way to break this ground loop is to lift the AC ground on one piece of equipment, typically the
power amplifier. This removes the safety AC ground. The system now relies upon the audio cable to
provide the ground ... a practice that is hazardous!!! You also put at risk your multi-pair snake,
console, post rack equipment, and most important the client. I do not endorse the use of AC ground lifts
for any system ... anywhere. Don't do it.

file:///F|/Books/grounding/TSC Tech Talk Grounding.htm (3 of 4)15/03/2007 10:02:21 •


TSC Tech Talk | Grounding

In certain situations you can lift the shield at one end (usually the output) of an audio cable and eliminate
the most likely path that carries ground loop currents. This is the way all TSC amp racks are wired and is
seen as standard for most tour type rigs. This method takes into account that the shield doesn't carry
audio signals. It does protect against static and radio noise. With one end lifted however, it continues to
reject static and other interference into the audio path. Note: don't cut the shield of a mic cable that
carries phantom power or you'll cut the power to the mic.

Maximize safety while avoiding ground loops


Try not to lift the safety ground on any piece of equipment. NEVER defeat the AC safety ground on
your console or any piece of equipment connected directly to your mics. Mics take priority in grounding
safety because the performers holding them may touch other grounded items, including a wet stage ...
and then .... !!!

Always try and plug your equipment into the same AC service leg. This includes FOH, amp land,
monitor land, and band back-line. This not only reduces the potenial of a ground loop, but also reduces
the danger of electrical shock.

Always connect lighting, air conditioning, rigging motor, and so on to a completely different phase or
leg of the main power distribution.

Remember to plan ahead and always think safety.

Written by Devin DeVore


References provided by: Ramsa, Yamaha, and Rane

Back to:

file:///F|/Books/grounding/TSC Tech Talk Grounding.htm (4 of 4)15/03/2007 10:02:21 •

You might also like