0% found this document useful (0 votes)
2K views2 pages

Wifi Extender U9

This quick installation guide summarizes how to set up a WiFi repeater in 3 steps: 1. Connect the extender to an electrical outlet near the host router and wait for the power indicator LED to turn solid green. 2. Configure repeater mode by either pressing the WPS button on the router and extender, or by connecting to the extender's network and logging into the web browser setup. 3. Wait for the power indicator LED to turn solid green again, then find extended wireless networks starting with "_EXT" to connect devices in dead zones.

Uploaded by

Marie Carmen Roy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
2K views2 pages

Wifi Extender U9

This quick installation guide summarizes how to set up a WiFi repeater in 3 steps: 1. Connect the extender to an electrical outlet near the host router and wait for the power indicator LED to turn solid green. 2. Configure repeater mode by either pressing the WPS button on the router and extender, or by connecting to the extender's network and logging into the web browser setup. 3. Wait for the power indicator LED to turn solid green again, then find extended wireless networks starting with "_EXT" to connect devices in dead zones.

Uploaded by

Marie Carmen Roy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Quick installation guide

4 Mode selection

Model:U9
Select host
Red
Select Repeater network
Pow erind icator
mode Click next
Enter your Host
router's the
password

/ W AN
Click and follow the Instructions
/ W AN
on the page to complete the configuration
Wait for the LED Solid green, You can find the
network names with _EXT in your Phone Wi-Fi network list

Relocate
LAN / W AN port
1.Plug the extender into an electrical outlet between your router (Host Network) and the Wi-Fi
/
“dead” zone.
The location you choose must be within the range of your existing host network.

WiFi Repeater mode 2. Wait until the LED is lit and solid Green. If not, relocate it closer to the router to achieve
a good (or better) signal quality.
In this mode, the router boosts the existing wireless coverage in your home.
1 Connect Your Router
Plug the extender into an electrical outlet near your host router, and
then wait until the LED is on and then off.

2 Configure repeater mode Relocate


Method ONE Using WPS (Wi-Fi Protected Setup) 1.Plug the extender into an electrical outlet between your router
Using WPS is an easier way to extend your host network.You are recommended to (Host Network) and the Wi-Fi “dead” zone.
The location you choose must be within the range of your existing
use this method if your hostrouter has the WPS button. The button might look like
host network.
one of these: , If not, please refer to Method Two
2. Wait until the LED is lit and solid Green. If not, relocate it

Connect closer to the router to achieve a good (or better) signal quality.

1.Press the WPS button on


your router
2.Within 2 minutes, press the
wps buttonon the extender
for 1 second.

RRID : RRID :

Wait for the LED Solid green,


You can find the network names
with _EXT in your PhoneWi-Fi network
list, indicating a successful WPS
connection.If not, please use Method TWO. Frequently Asked Questions(FAQ)
Q1. What can I do if the login window does not appear?
If the computer is set to a static or fixed IP address, change the setting to obtain an IP address automatically.
3 Login Verify if http://192.168.11.1 is correctly entered I in the web browser.
Method TWO Using a Web Browser
For Mobile phone users 1.Launch a web browser and type http://192.168.11.1 in the Make sure your computer is connected to the Mini Router’s network.
Connect to the U9 router address field.( If the phone is connected to the repeater Use another web browser and try again.
for the first time, The phone will automatically pop up the
1.Find the SSID(Network Name) printed on the lable of the U9 router.
login page)
Reboot your router and try again.
2.Connect your Mobile phone to the U9 router‘s network Disable the network adapter used currently and then enable it again.
2. Use admin (all lowercase) for Password to login. Q2. What can I do if I cannot access the Internet?
Check if the internet is working properly by connecting a computer directly to the modem via Ethernet cable. If not,
connect your internet provider.
Reboot your router and try again.
Extender-a4f97c Q3. How do I restore the router to its factory default setting?
While the router is powered on, press and hold the reset button on the rear panel of the router for approximately
admin 5 seconds.
Q4. Why set the repeater mode is unsuccessfully?
You may have typed in the router’s wireless password incorrectly, please log in and check the wireless password.
The Mini router may be out of range, please move it closer to the router.
Connect to the extender’network: Extender-a4f97c
(The SSID on the lable of the U9 router)
Please reset the Mini Router and go through the configuration again.
A.If you need reset the extender. You need press and hold the reset button inside the tiny hole for 10 seconds.

AP mode Router mode


2.Connect to the U9 router 2.Connect to the U9 router
In this mode, the router transforms your existing wired network to a wireless .
For Mobile phone users
1.Find the SSID(Network Name) printed on the lable of the U9 router.
1.Connect Your Router For Mobile phone users
1.Find the SSID(Network Name) printed on the lable of the
If your Internet connection is through a DSL/Cable modem,follow steps 1,2
1.Connect Your Router 2.Connect your Mobile phone to the U9 router‘s network
and 4 to complete the hardware connections.
U9 router.
2.Connect your Mobile phone to the U9 router‘s network
If your Internet connection is through an Ethernet cable form the wall,follow
steps 3 and 4 to complete the hardware connections.

To LAN/WAN

To LAN/WAN
Connect to the extender’network: Extender-a4f97c Connect to the extender’network: Extender-a4f97c
(The SSID on the lable of the U9 router) (The SSID on the lable of the U9 router)

3. Login 4. Mode selection


3. Login 4. Mode selection 1.Launch a web browser and type http://192.168.11.1 in the address field.
1.Launch a web browser and type http://192.168.11.1 in the address field. ( If the phone is connected to the repeater for the first time, The phone
( If the phone is connected to the repeater for the first time, The phone will automatically pop up the login page)
will automatically pop up the login page) 2. Use admin (all lowercase) for Password to log in.
2. Use admin (all lowercase) for Password to log in.

admin

admin
Select Router mode

Select AP mode Click next

Click next 1 If you choose Dynamic IP,Dynamic IP users are usually


5.Set up Your Internet Connection
equipped with a cable TV or fiber cable.
You can modify the settings according to the
service information provided by your ISP.

Either keep the


SSID and Password
Click and follow the prompts on the page to or customize it for
complete the AP mode configuration the extended

Either keep the


Select your internet
SSID and Password connectiontype from Click and follow the prompts on the page to
or customize it for the drop-down list
complete the Router mode configuration
the extended
2 If you choose Static IP,enter the information provided by your ISP 3 If you choose PPPoE,enter the username and password
in the corresponding fields. provided by your ISP.
PPPoE users usually have DSL cable modems.
Frequently Asked Questions(FAQ)
Q1. What can I do if the login window does not appear?
If the computer is set to a static or fixed IP address, change the setting to obtain an IP address automatically.
Verify if http://192.168.11.1 is correctly entered I in the web browser.
Make sure your computer is connected to the Mini Router’s network.
Use another web browser and try again.
Reboot your router and try again. Enter the information provided by Enter the username and
Disable the network adapter used currently and then enable it again. your ISP,in the corresponding fields password by your ISP.
Q2. What can I do if I cannot access the Internet?
Check if the internet is working properly by connecting a computer directly to the modem via Ethernet cable. If not, Either keep the SSID and
connect your internet provider.
Passwordor customize it
Reboot your router and try again.
for the extended
Q3. How do I restore the router to its factory default setting?
While the router is powered on, press and hold the reset button on the rear panel of the router for approximately
5 seconds. Either keep the SSID and Password
Q4. Why set the repeater mode is unsuccessfully? or customize it for the extended Click and follow the prompts on the page to
You may have typed in the router’s wireless password incorrectly, please log in and check the wireless password. complete the Router mode configuration
The Mini router may be out of range, please move it closer to the router.
Please reset the Mini Router and go through the configuration again.
Click and follow the prompts on the page to
A.If you need reset the extender. You need press and hold the reset button inside the tiny hole for 10 seconds.
complete the Router mode configuration
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment. This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
‐‐ Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
RF Exposure Statement
To maintain compliance with FCC's RF Exposure guidelines, This equipment should be
installed and operated with minimum distance of 20cm the radiator your body. This device
and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.

You might also like