Preboard Exam Practical SPDI

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 17

Padilla Manila Master Plumber review

[email protected] Switch accounts
 
*Required

February 2023 Pre Board :  Sanitation Plumbing Design and Intallation  (100Items)
The spout of a lavatory faucet with P.O. assembly is also the housing for:*
1 point

a. a left rod that connects to the plunger rod


b. many types of soap dispensers
c. a backflow prevention device
d. none of the above

Handicap sink installation require that metallic pipe that could become hot from water flow be:*
1 point

a. Replaced with plastic piping


b. Protected (covered)
c. Labeled to warn the user of hot water
d. None of the above

A lavatory with pop-up drain assembly connects to the drain using a:*
1 point

a. 1 1/2” flanged tailpiece


b. 1 ¼” flanged tailpiece
c. 1 1/2” threaded tailpiece
d. 1 ¼” threaded tailpiece

Two fixtures that have overflow protection are the:*


1 point

a. Shower and lavatory


b. Laundry sink and kitchen sink
c. Bathtub and lavatory
d. Bathtub and bar sink

A kitchen sink faucet that has a base plate and a separate spray requires a:*
1 point

a. Two-hole sink
b. Three-hole sink
c. Four-hole sink
d. None of the above
The rims of bowls used for handicap toilets and non-handicap toilets:*
1 point

a. Are the same height from the floor


b. Are installed at different distances from a back wall
c. Connect differently to the drain
d. Are not the same height from the floor

Most urinals water supply size is:*


1 point

a. 1⁄2”
b. 3⁄4”
c. 1”
d. 1 1⁄4”

Most codes dictate that a fixture cannot be supplied with more than:*
1 point

a. 100 pounds of pressure


b. 90 pounds of pressure
c. 80 pounds of pressure
d. None of the above

Copper piping used for medical gas systems should only be cut with a:*
1 point

a. Hack saw
b. Band saw
c. Reciprocating saw
d. Copper tubing butter

Potable water is also:*


1 point

a. Known as drinking water


b. The opposite of non-potable
c. Used for cooking
d. All of the above

A short length of pipe with threads at each end; used to join couplings or fittings*
1 point

a. Dead End
b. Nipple
c. Fixture Branch
d. Thimble

Trap size of fixtures for Sinks (Dishwashers).*


1 point

a. 1”
b. 1 ½”
c. 1 ¼”
d. ½”

A pipe connecting upward from a soil and waste stack to a vent stack for the purpose of
preventing pressure changes in the stack.*
1 point

a. Yoke vent
b. Wet vent
c. Dry vent
d. Local vent

Trap size of fixtures for Drinking Fountain.*


1 point

a. ½”
b. 1 ¼”
c. ¼”
d. 1”

A trench containing course aggregate and a distribution tile pipe through which septic tank
effluent may flow covered with earth. 
*
1 point

a. Absorption trench
b. Illumination
c. Air trap
d. Catch basin

The water supply to a water closet utilizing a flush valve (flushometer) is:*
1 point

a. ½”
b. ¾”
c. 1”
d. 1 ¼”

The maximum concentration (amount) of a chemical worker can be exposed to is known as:*
1 point

a. Permissible exposure level


b. Individual tolerance level
c. Maximum exposure limit
d. Concentration allowance

LFL is the abbreviation for:*


1 point

a. Limit Flame Level


b. Level Floor Limit
c. Lower Flammable Limit
d. Level Flammable Limit

GCFI is the abbreviation for:*


1 point

a. Ground Fault Circuit Installation


b. Ground Fault Circuit Interrupter
c. Ground Force Circuit Interrupter
d. Ground Failure Circuit Interrupter

Safety is the responsibility of:*


1 point

a. Everyone
b. The employer
c. The employee
d. OSHA

An extension ladder must extend above a roof by at least:*


1 point

a. 3 feet
b. 2 feet
c. 1 feet
d. 4 feet

Codes dictate the _______ be installed in the cold water piping near a water heater.*
1 point

a. An isolation valve
b. A circulating pump
c. A pressure booster
d. All of the above

PPE is the abbreviation for:*


1 point

a. Personal plumbing equipment


b. Plumbing product equivalent
c. Personal protective equipment
d. Personal protection equipment
The safe oxygen level of a confined space is between:*
1 point

a. 19% and 23%


b. 19% and 23.5%
c. 20% and 24%
d. None of the above

The four classification of soil are:*


1 point

a. Stable rock A, B, C
b. Stable rock 1, 2, 3
c. Both A & B
d. None of the above

Trap size of fixtures for Fountain cupsiders.*


1 point

a. 1 ½”
b. 1 ¼”
c. 1’’
d. ½”

Fitting for base or soil stack and building drain.*


1 point

a. ½” bend
b. 1 ¼” bend
c. 1 ½” bend
d. ¼” bend

The length along the center of the pipe and fitting.*


1 point

a. Fixture branch
b. Soil pipe
c. Developed length
d. Invert

Trap size of fixtures for Floor drain.*


1 point

a. 2”
b. 2 ½”
c. 4”
d. 3”
Moderately noisy. Similar to siphon jet except that trap passageway and water surface area are
smaller.*
1 point

a. Wash down
b. Reverse trap
c. Bidet
d. Blow out

One vertical foot of water weighs?*


1 point

a. 12 pounds per square inch


b. 8.33 pounds per square foot
c. 0.434 pounds per square inch
d. 1 pound per cubic foot

CPVC is the abbreviation for:*


1 point

a. Chlorinated polyvinyl chloride


b. Calcium polymer vinyl composite
c. Chlorinated polymer virgin
d. All of the above

The wheels used with scaffolding are called:*


1 point

a. Wheels
b. Casters
c. Rollers
d. Tires

To minimize water hammer:*


1 point

a. A quick-closing valve is installed


b. A shock absorber is installed
c. All water hammer arrestors are removed
d. None of the above

To capture rainwater for future use serving irrigation systems:*


1 point

a. A cistern is used
b. The roof gutters are piped to a well
c. A special plumbing permit is required
d. None of the above
Urinal is abbreviated as:*
1 point

a. U
b. UR
c. URN
d. URNL

PVC pipe cannot be used for:*


1 point

a. Hot water distribution systems


b. Cold water service from a water meter to a building
c. Venting drainage system
d. Drains and sewers

A 45 degree fitting is:*


1 point

a. One-sixteenth of a circle
b. One-eighth of a circle
c. One-fourth of a circle
d. One-half of a circle

A ball valve:*
1 point

a. Has a lever handle for manual types


b. Can be purchased as an automatic type
c. Has an internal ball with a core drilled through its center
d. All of the above

Using 1/8” scale to interpret a blueprint dimension means that 1/8” equals:*
1 point

a. One foot
b. One yard
c. One inch
d. One eight

EWC is the abbreviation for:*


1 point

a. Electric water circulator


b. Electric water cooler
c. Energized water circulator
d. Energized water cooler

WS is the abbreviation for:*


1 point

a. Waste system
b. Waste stack
c. Water system
d. Water stack

ADA is the abbreviation for:*


1 point

a. Americans Disabled Action


b. Americans Disabled Act
c. Americans with Disabilities Act
d. Americans with Disabilities Action

A water service pipe must be installed per local codes, but always:*
1 point

a. Below the frost level


b. Using galvanized steel pipe
c. Below a sewer when in the same trench
d. All of the above

Water quality of private well is the responsibility of:*


1 point

a. The environmental protection agency


b. The local jurisdiction where the well is located
c. The owner of the well
d. None of the above

An isometric drafting triangle can be used to create:*


1 point

a. 30 deg angles
b. 60 deg angles
c. 90 deg angles
d. All of the above

Surface water is:*


1 point

a. Portable and not requiring treatment


b. A lake or river
c. The top layer or groundwater
d. None of the above

A full circle connected to a line illustrated is a plan view of a piping system indicates that is a:*
1 point
a. Pipe stubbing out
b. Pipe turning down
c. Pipe turning up
d. None of the above

SV is the abbreviation for service weight cast iron and:*


1 point

a. Sink venting
b. Supply vertical
c. Supply vented
d. Stack vent

A water closet is also a:*


1 point

a. Lavatory
b. Sink
c. Toilet
d. Tub

. A pipe installed to vent, a fixture trap and which connects with the vent system above the
fixture served or terminates in the open air.*
1 point

a. Individual vent
b. Stack vent
c. Loop and circuit vent
d. Relief vent

Trap size of fixtures for Wash basin.*


1 point

a. 1 ¼”
b. 1”
c. 2 ¼”
d. 2”

Trap size of fixtures for slop sinks (ordinary).*


1 point

a. 2”
b. 3”
c. 1”
d. 4”

Minimum cost. Least efficient subject to clogging, noisy. Simple washout and emptying through
small irregular passage way, prohibited by some health codes.*
1 point

a. Wash down
b. Reverse trap
c. Blow out
d. Bidet

Trap size of fixtures for Urinals (through).*


1 point

a. 1”
b. 2”
c. 2 ¼”
d. 1 ½”

A clevis hanger uses threaded rod along with:*


1 point

a. Wood screws
b. Hex nuts and possibly washers
c. Anchor bolts
d. A threaded thimble

A kitchen sink rough-in:*


1 point

a. Can be served by a stub-up or a stub-out


b. Can only be served by a stub-out
c. Can only be served by a stub-up
d. None of the above

A split hanger:*
1 point

a. Is only used for horizontal installations


b. Is only used for vertical installations
c. Is used for all pipe positions
d. Is only used for copper pipe

A tank-type water supply rough-in is:*


1 point

a. Usually installed on the left side of the fixture


b. Always installed on the left side of the fixture
c. Always installed of the right side of the fixture
d. Can be on either side of the fixture

The most severe burn is:*


1 point
a. First Degree
b. Second Degree
c. Third Degree
d. Fourth Degree

A handheld shower hose the could be submerged in bath water must:*


1 point

a. Be no longer than 36 degrees


b. Always have a backflow prevention device installed
c. Never have backflow prevention device installed
d. Always be at least 5” in length

Water supply rough-in for a flush valve (flushometer) that serves a toilet is:*
1 point

a. The same as for a tank-type


b. Larger than a tank-type toilet
c. Can be located on either the left or right side of the center of the fixture
d. Both b & c

Clevis hanger are used for:*


1 point

a. Horizontal installations only


b. Vertical installations only
c. Vertical and horizontal installations
d. None of the above; they are not allowed

One important concern when installing an electric water heater is:*


1 point

a. Ensuring that the gas pipe is sized correctly


b. Confirming that the electrician is licensed
c. Ensuring that all devices and controls can be readily accessed
d. Whether the storage tank is a top-fed type

A gooseneck spout is used on:*


1 point

a. Shower faucets
b. Tub faucets
c. Sink faucets
d. None of the above

Includes water supply and distribution pipe; plumbing fixture and traps, soil, waste and vent
pipes; house drain and house sewers including their respective connections.*
1 point
a. Water reservoir
b. Siamese connections
c. Plumbing system
d. Trap seal

Trap size of fixtures for Water closets.*


1 point

a. 4”
b. 6”
c. 2”
d. 3”

Ratio of water closets for female population for elementary and secondary school.*
1 point

a. Ratio of 1:45
b. Ratio of 1:25
c. Ratio of 1:55
d. Ratio of 1:30

A valve which in the water flow is shut off by a flat disk that is screwed down onto its seat.  *
1 point

a. Compression valve
b. Overhead storm drain
c. Pressure reducing valve
d. Union patente

The luminous flux density incident on a surface.*


1 point

a. Illumination
b. Flood level
c. Plumbing system
d. Fixture branch

One btu increases the water temperature of _______ by one degree Fahrenheit.*
1 point

a. One gallon
b. One pound
c. One quart
d. One ounce

DW is the abbreviation for:*


1 point

a. Dishwasher
b. Drain wall
c. Discharge waste
d. Drainage waste

Zero gauge pressure is also atmospheric pressure and is:*


1 point

a. 14.7 pounds per square inch at sea level


b. 29.00 inches of mercury
c. Both a&b
d. None of the above

One btu at sea level is equal to:*


1 point

a. 0.80 btu at 5,000 feet above sea level


b. 0.60 btu at 10,000 feet above sea level
c. 0.88 btu at 3,000 feet above sea level
d. All of the above

Water boils at sea level under normal atmospheric pressure at a temperature of:*
1 point

a. 210 deg Fahrenheit


b. 211 deg Fahrenheit
c. 212 deg Fahrenheit
d. 213 deg Fahrenheit

Urinals and commercial toilets that do not use a tank receive water supply from:*
1 point

a. An angle stop
b. A straight stop
c. A dual stop
d. A flush valve (flushometer)

A floor-mounted toilet that connects to a closet flange uses:*


1 point

a. a wax seal and set of closet bolts


b. a rubber gasket and one closet bolts
c. putty and a set of closet bolts
d. caulk and a set of closet bolts

The vertical distance from a faucet spout outlet to the flood-level rim of a fixture is called:*
1 point

a. Flow space
b. Aerator distance
c. Backflow gap
d. Air gap

A lavatory pop-up assembly is:*


1 point

a. One required for wall-hung sinks


b. 1 1⁄2” and is not sold with a faucet
c. 1 1⁄4” and sealed with putty or caulk
d. 1 1⁄4” and only sealed with putty

The tub spout with a diverter feature is used to:*


1 point

a. Divert water to the tub


b. Stop all flow from the faucet
c. Divert water to the showerhead
d. None of the above

Trap size of fixtures for Combination Fixture*


1 point

a. 1”
b. 1 ½”
c. ¼”
d. ½”

Color coding of high pressure steam*


1 point

a. Black
b. White
c. Blue
d. Green

A passage under a road, embankment or canal which allow for the flow of water.*
1 point

a. Cistern
b. Culvert
c. Catch basin
d. Air trap

Is the backflow of used, contaminated or polluted water from a plumbing fixture due to negative
pressure.*
1 point

a. Backflow
b. Back siphonage
c. Yoke vent
d. Friction loss

Is the lowest portion of the inside of any pipe or conduit that is not vertical.*
1 point

a. Invert
b. Fixture branch
c. Soil pipe
d. Rough-in

Laundry sinks are available to install in a countertop, onto a wall, and:*


1 point

a. Floor-mounted with legs


b. Both are always fiberglass
c. Have very shallow bowls
d. None of the above

A bidet drain assembly is:*


1 point

a. 2”
b. 1 ½”
c. 1 ¼”
d. None of the above

A slip joint style p-trap connects to the drainage system using a:   *
1 point

a. Coupling
b. Trap adapter
c. Male and female adapter
d. None of the above

A dip tube:*
1 point

a. Is used on bottom-fed water heaters


b. Funnels water to the bottom of a storage tank
c. Is located on the hot water side of a heater
d. None of the above

A tankless water heater is:*


1 point

a. Only available in gas


b. Only available in electric
c. Only capable of storing 10 galloons
d. Available is gas and electric

Heat exchanger transfer heat from a hot object, vapor, or fluid to:*
1 point

a. Water
b. Convert the heat electricity
c. Heat an occupied space only
d. None of the above

Water that is subjected to negative pressure (vacuum) boils:*


1 point

a. at 235 degree Fahrenheit


b. only at high altitudes
c. at lower temperatures
d. at sea level

A coupling*
1 point

a. Connects a pipe and a valve


b. Connects two pipes together
c. Is only used with materials of different types
d. Connects three pipes together

One kilowatt is equal to:*


1 point

a. 1,000 watts
b. 3,412 btus
c. Both a&b
d. None of the above

The trade name for a combination wye and eight bend is:*
1 point

a. Sanitary tee
b. Sanitary cross
c. 45 deg wye
d. Combo

IPS is the abbreviation for:*


1 point

a. Internal pipe indicator


b. Inside pipe size
c. Iron pipe size
d. Internal pipe size
An underground structure for drainage into which water from the roof or floor will drain through
sewer.*
1 point

a. Cistern
b. Corporation stop
c. Absorption trench
d. Catch basin

An underground tank reservoir to store water.*


1 point

a. Catch basin
b. Corporation stop
c. Cistern
d. Absorption trench

Ratio of water closets for female population for principal worship places.*
1 point

a. Ratio of 1:75
b. Ratio of 1:60
c. Ratio of 1:85
d. Ratio of 1:70

Noisy but highly efficient. Strong jet into leg forces contents out. Higher pressure required.
*
1 point

a. Bidet
b. Reverse trap
c. Siphon-jet
d. Blow out

Back

Submit
Page 2 of 2

Clear form
Never submit passwords through Google Forms.
This form was created inside padillamanila.page. Report Abuse

 Forms

You might also like