GV-Edge Recording Manager User Manual
GV-Edge Recording Manager User Manual
GV-Edge Recording Manager User Manual
User's Manual
ERMV223-UM-A
© 2022 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
http://www.geovision.com.tw
August 2022
Scan the following QR codes for product warranty and technical support
policy:
Introduction.................................................................. 1
Features ......................................................................................................................... 2
System Requirements .................................................................................................... 3
Supported GeoVision Products ...................................................................................... 4
GPU Decoding Specifications ........................................................................................ 6
i
3.2 Renaming Devices .................................................................................................22
3.3 Synchronizing Host Time ........................................................................................22
3.4 Connecting to Hosts with Identical Credentials .......................................................23
3.5 Updating Host Information ......................................................................................23
3.6 Configuring NAS.....................................................................................................24
3.6.1 Assigning NAS Storage for Recording ......................................................... 25
3.6.2 Changing the NAS Storage for Recording ................................................... 27
3.6.3 Deleting the NAS Storage for Recording ..................................................... 27
3.6.4 Viewing Storage Information ....................................................................... 27
Chapter 6 Playback................................................... 46
6.1 The Playback Window ............................................................................................46
ii
7.3.1 Exporting Settings ....................................................................................... 54
7.3.2 Importing Settings ....................................................................................... 54
Appendix .................................................................... 57
PTZ Control Using GV-Joystick .....................................................................................57
iii
Chapter 13 Audio Communication .......................... 89
Chapter 14 Playback................................................. 90
Specifications ...........................................................100
iv
Preface
Welcome to GV-Edge Recording Manager User Manual.
Important Notice
Before upgrading to GV-Edge Recording Manager (Windows Version) V2.0.0, take note of
the following:
1. Administrator Password and Host List settings will remain unchanged after upgrading
from V1.4.0 to V2.0.0.
2. When using the Import / Export Data functions (see 7.3 Exporting and Importing
Settings) to import previously saved settings from V1.4.0 to V2.0.0, only the
Administrator Password and Host List settings will be applied.
v
Naming and Definition
GV-DVR / NVR GeoVision Analog and Digital Video Recording Software. GV-
DVR / NVR also refers to Multicam System or GV-Hybrid DVR.
GV-Recording Server GeoVision video streaming server designed for large-scale video
surveillance deployments that can record up to 256 channels
while transmitting up to 600 channels.
Manager
To upgrade GV-Edge Recording Manager, run the Installer (setup.exe) included in the latest
software downloads from our website. Select Reinstall / Upgrade to start.
vi
Introduction
GV-Edge Recording Manger is designed for remote live viewing and playback of GeoVision
IP devices and software. GV-Edge Recording Manager provides an integrated interface for
you to access live view, assign recording to NAS servers, enable/disable recording, play
back videos and even view storage information of IP cameras -- without visiting each host’s
Web interface. Any connection to hosts can be stopped without affecting the recording and
normal functioning of the devices.
GV-Edge Recording Manger brings live view and allows remote control of GV-IP Camera,
GV-Video Server and GV-SNVR, as well as GV-DVR / NVR / VMS and GV-Recording Server,
together under one management interface.
Video Source
PC installed with
GV-Edge Recording Manager
GV-Recording Server / Win or Mac Versions
GV-DVR / NVR / VMS Video Gateway (Live View / Playback)
GV-IP Cameras
1
Features
Windows Version
⚫ Display up to 32 channels for free, up to 64 channels plus GV-Joystick, using a GV-
USB dongle
⚫ On-demand display for dual channels
⚫ Fisheye dewarping
⚫ Varieties of live view displays: PIP / PAP View, Focus View, Scan Window, projecting a
live view display onto another monitor
⚫ Take snapshots of live images
⚫ Remotely enable or disable recording to GV-IP Camera, GV-DVR / NVR / VMS
⚫ Assign NAS storage for recording
⚫ Remote playback
⚫ Batch IP address assignment
⚫ PTZ control
⚫ Two-way audio
⚫ Import and export of system configuration
⚫ Storage information (free and occupied space) of GV-IP Camera
⚫ Trigger output devices of connected hosts
Mac Version
2
System Requirements
Make sure that you install GV-Edge Recording Manager to a computer that meets the
following system requirements.
3
Supported GeoVision Products
GV-IP Devices Supported Version
GV-IP Camera All GV-IP Cameras with the latest firmware.
GV-VS11 V1.03 or later
GV-VS12 V1.07 or later
GV-VS14 V1.01 or later
GV-Video Server
GV-VS2400/2420 V1.00 or later
GV-VS2800/2820 V1.00 or later
GV-VS21600 V1.00 or later
GV-SNVR0400F V1.10 or later
GV-SNVR0411 V2.10 or later
GV-SNVR0412 V1.00 or later
GV-SNVR0811 V2.40 or later
GV-SNVR System
GV-SNVR0812 V1.00 or later
GV-SNVR1600 V1.10 or later
GV-SNVR1611 V1.00 or later
GV-SNVR1612 V1.00 or later
UA-SNVRL810-P V1.00 or later
UA-SNVR System
UA-SNVR1620 V1.00 or later
UA-XVL810 V1.00 or later
UA-HD DVR UA-XVL1610 V1.00 or later
UA-XVR810 V1.00 or later
UA-IP Camera All UA-IP Cameras with the latest firmware.
GV-Software Supported Version
GV-Recording Server V1.2.4.0 or later
GV-Video Gateway V1.2.4.0 or later
GV-DVR / NVR V8.7.1.0 or later
GV-VMS V14.10 or later
Note:
1. For the NAS application, it is required to use GV-IP Cameras (firmware V3.00 or later),
GV-Target Cameras (firmware V1.02 or later), GV-EFD2101 / EFD3101 / EVD2100 /
EVD3100 (firmware V1.00 or later).
2. Files recorded to GV-NAS Systems are stored in MPEG4 format and those recorded to
memory cards are stored in AVI format.
4
3. Remote playback from SD card is not supported for the following models: GV-ABL / TBL
Series, GV-ADR / TDR Series, GV-AVD / TVD Series, GV-EBD Series, GV-QSD5730 /
5731-IR, GV-SD2322-IR / 2722-IR / 3732-IR, UA-B580F3 / R500F2 / R560F2 / R580F2 /
R800F2.
4. Adjusting dome view of PTZ cameras by double-clicking on the live view is not supported
for those added via GV-VMS.
5. The Center Move function of GV-PTZ cameras is not supported for such added via GV-
Recording Server / SNVR / VMS.
6. The following features are not supported by GV-SNVR:
A. Instant playback (No. 2, Figure 4-1).
B. Audio not supported for recording backup.
5
GPU Decoding Specifications
GPU (Graphics Processing Unit) decoding can lower the CPU loading and increase the total
frame rate supported by GV-Edge Recording Manager. GPU decoding can be performed on
onboard GPU, external GPU, or both, under the following specifications.
Onboard GPU: GPU decoding is only supported when using the following Intel chipsets:
For H.264 Video Compression
⚫ 2nd ~ 8th Generation Intel Core i3 / i5 / i7 Desktop Processors
⚫ 9th ~ 11th Generation Intel Core i3 / i5 / i7 / i9 Desktop Processors
External GPU: GPU decoding is only supported when using NVIDIA graphics cards with
compute capability 3.0 or above and memory 2 GB or above. To look up the commute
capability of the NVIDIA graphics cards, refer to: https://developer.nvidia.com/cuda-gpus.
Note:
1. One external NVIDIA graphics card can be supported by GV-Edge Recording Manager
2.0.0 or later to perform GPU decoding at free of charge.
2. NVIDIA GeForce GTX 1060 is not supported.
Onboard GPU + External GPU: To have both the on-board VGA and external VGA
perform GPU decoding, the VGAs must follow their respective specifications listed above.
Note:
1. If you have both on-board and external VGA installed, the on-board VGA must be
connected to a monitor for H.264 / H.265 GPU decoding.
2. CUDA compute capability 5.0 or higher is required to ensure optimal performance.
6
Software Specifications
GPU decoding is only supported under the following operating system, resolution, and codec.
7
Windows Version
8
Chapter 1 Overview
1.1 Main Window
1 3
Figure 1-1
1 Camera Channels Displays the live views / recordings of added hosts. For details,
see 4.1 The Live View Window or Chapter 6 Playback.
2 Device Lists & Contains the hosts added to GV-Edge Recording Manager and
Layout their I/O devices, and configures layout settings. For details,
see 1.3 The Host List and 4.2 Live View Layouts.
9
1.2 The Toolbar
2 3 4 5
Figure 1-2
2 Full Screen Diminishes all setting windows and toolbars and displays only
the main screen.
3 Close All Videos Closes all videos currently streamed on the main screen.
10
1 Overview (Windows Version)
2 4
1 3 5
Figure 1-3
11
1.4 The I/O List
You can trigger output devices of the connected hosts in the I/O List.
Drag and drop the I/O hosts directly into the I/O List to add the subordinate I/O devices. To
trigger an output, click the Output button in the I/O List.
Figure 1-4
Note:
1. GV-Edge Recording Manager cannot connect to an I/O box directly.
2. Up to 5 I/O hosts can be added to the I/O List.
12
Chapter 2 Getting Started
2.1 Installing GV-Edge Recording Manager
Follow the steps below to install GV-Edge Recording Manager from the GeoVision Website.
To access account-related settings, click the Account Settings button on the main screen >
Account Setup. The Account Setup dialog box appears.
Figure 2-1
13
Name Description
Privilege Enable the privileges to the Guest. Allow the Guest to access
playback (Remote ViewLog) and back up and export
recordings (Backup/Export Remote ViewLog Data).
Note: The Guest account does not have a password and only has access to the live
view and playback of the connected hosts.
1. On the Host List, click Add > Add Host > Search Host. GV-IP Devices and servers
installed with GeoVision software within the same LAN are listed in the Search Host
window.
Figure 2-2
14
2 Getting Started (Windows Version)
2. When the search is finished, you are prompted to reassign the IP addresses of certain
IP devices found. To optionally assign new IP addresses for these devices:
B. Optionally select and modify the Subnet Mask, Default Gateway and DNS Server
if needed.
C. Click Start. The select devices are assigned with the new IP addresses starting from
the Start IP Address, in sequential order.
A. Click on the left top of the Search Host window. This dialog box appears.
Figure 2-3
B. Type the ID and Password for all the hosts and click OK.
A. Click a host to be added. The ID and password request appear (Figure 2-3).
B. Type the ID and Password of the selected host and click OK.
5. Click the Add Selected Hosts button to add the selected hosts. A prompt appears.
6. Click OK to accept the prompt. The selected hosts are added to the Host List.
7. Once added, users can drag and drop the desired cameras from the Host List onto the
Live View Window for live view display. See Chapter 4 Live View for details.
Note:
1. If a router or firewall is installed, ensure the following communication ports required by
the Host Search function are open:
⚫ TCP/IP ports 5201 (for searching GV-DVR / NVR / VMS) and 5202 (for searching
GV-IP Devices)
⚫ Multicast port 5200
To change the mentioned default ports, see 2.3.1.1 Changing Network Port Settings.
2. If antivirus software is installed, the Search Host function may be interfered and will
not detect the available hosts. In this case, turn off the antivirus software and try again.
15
2.3.1.1 Changing Network Port Settings
To access GV-Edge Recording Manager’s port settings, follow Step 1 in 2.3.1 Automatically
Adding Multiple Hosts and click Configure in the Search Host window. The Network dialog
box appears.
For searching GV-DVR / NVR hosts, the default TCP/IP port is 5201 and 5200 for multicast
port. For searching IP devices, the default TCP/IP port is 5202. You can select a LAN card to
perform the search for IP devices if you have more than one LAN card installed. Keep the
default settings and only change them when necessary.
16
2 Getting Started (Windows Version)
1. From the Host list, click Add > Add Host and select a device type. The Host
Settings dialog box appears. The settings may vary slightly for different device types.
The following is an example of IP Camera.
Figure 2-6
2. Type the Host Name, IP Address, ID and Password of the host. Modify the
Communication Port if necessary.
3. Click the Update Information button to request for the number of cameras and I/O
modules installed.
4. Click OK to add the host. The host is added to the Host List.
5. Once added, users can drag and drop the desired cameras from the Host List onto the
Live View Window for live view display. See Chapter 4 Live View for details.
17
2.3.3 Connecting to GV-DVR / NVR / VMS
1. To add GV-DVR / NVR / VMS hosts, make sure that Control Center Service and
Remote ViewLog Service are enabled ahead to allow remote access from GV-Edge
Recording Manager. (Network button > Control Center Server > Start Default Service).
[GV-DVR / NVR]
Figure 2-7
[GV-VMS]
Figure 2-8
18
2 Getting Started (Windows Version)
2. For GV-VMS V16.11 or later, you can specify the time length allowed for GV-Edge
Recording Manager to access GV-VMS. To do this, click the account ID at the top of
GV-VMS’s main screen, click Password Setup > Local Account Edit. In the Control
Center tab, select the Limit Connection Time option and specify the time length
between 10 and 3600 seconds.
Figure 2-9
3. By default, the live stream images of GV-VMS are compressed for better bandwidth
control at the cost of increased CPU usage. The number of remote connections allowed
from the same GV-VMS depends on the specs and the usage of the VMS’ CPU.
4. For GV-VMS V17.1 or later, you can enable the Substream FIFO function under CMS
Service settings (Network button > Control Center Server > Control Center Service) for
improved streaming quality from GV-VMS at the cost of increased bandwidth. The
number of remote connections allowed from the same GV-VMS depends on the amount
of bandwidth available.
Figure 2-10
19
2.3.4 Creating a Camera Group
You can add multiple cameras to a group and drag the group onto a live view grid for display.
At least 8 cameras are required on the Host List for this function to work.
1. On the Host List, click Add > Add Group and type a name for the group.
2. Drag the desired cameras into the group.
3. Drag the created group onto a live view grid for display.
20
3 Batch Management (Windows Version)
Note: The batch management function is only supported by GV-Video Server and GV-IP
Cameras.
1. On the Host List, click Tools > Auto Set IP Address. The Auto Set IP Address
dialog box appears.
2. Select the devices to be configured from the Host Name column. To select all devices,
click .
3. To assign consecutive IP addresses to multiple GV-IP Devices:
A. Configure the Start IP address, Subnet Mask, Default Gateway and DNS server.
B. Click the button to preview the new IP address in the Assign IP column.
4. Click Start to apply the changes.
Figure 3-1
21
3.2 Renaming Devices
You can modify the device names of multiple hosts at a time.
Note: The batch management function is only supported by GV-Video Server and GV-IP
Cameras.
1. On the Host List, click Tools > Upgrade Device Name. The Upgrade Device Name
dialog box appears.
2. Select the devices to be configured from the Host Name column. To select all devices,
click the square .
3. Type the new device name directly in the Rename column.
Figure 3-2
Note:
1. Make sure you have disabled device monitoring before synchronization.
2. The batch management function is only supported by GV-Video Server and GV-IP
Cameras.
1. On the Host List, click Tools > Time Synchronization with Edge Recording
Manager.
2. Select the devices you wish to synchronize with GV-Edge Recording Manager and click
Start to sync.
22
3 Batch Management (Windows Version)
3. The common ID and Password will be filled in the Host Settings of the selected hosts,
as illustrated below.
Figure 3-3
23
1. On the Host List, right-click on the desired hosts (or a group), and select Update.
Figure 3-4
2. The Update Host Information window appears, listed with the selected hosts.
3. Select / deselect hosts and click Update Information to start updating the information
from hosts.
To see whether your camera models can record to NAS devices, check the NAS feature in
from this table.
IMPORTANT:
1. For the NAS application, it is required to use GV-IP Cameras (firmware V3.00 or
later), GV-Target Cameras (firmware V1.02 or later), GV-EFD2101 / EFD3101 /
EVD2100 / EVD3100 (firmware V1.00 or later).
2. For system performance and compatibility, it is highly recommended to use GV-NAS
Systems for recording.
3. Make sure the computer installed with GV-Edge Recording Manager is under the
same LAN with the NAS devices.
24
3 Batch Management (Windows Version)
1. On the Host List, click Tools > NAS Setup. The cameras that support NAS devices
appear in the NAS Setup window.
Figure 3-5
2. Select cameras for NAS management and click Start. The NAS Setup window appears.
3. Click Search for network host to detect the NAS installed within the LAN. The
detected network hosts are listed.
Figure 3-6
25
4. Select a NAS from the list and click the Search the host’s network storage button to
detect its shared folder(s). This dialog box appears.
Figure 3-7
5. Type the administrator username and password of the NAS device that allows for
highest level of access. The server’s folders are detected and shown.
Figure 3-8
A C D
B
B
Figure 3-9
A. On the NAS Setup window, select at least one camera to assign the storage path.
B. Select a NAS folder from the list and click Select this storage path for the device
to assign this storage path. The storage path appears in the Storage Path
column immediately.
26
3 Batch Management (Windows Version)
D. In the Storage Path column, you can manually change the IP address of a NAS.
Note:
1. Be sure that you assign each IP camera to record to a different user account in GV-
NAS System to avoid disrupting the recycling process.
2. For GV-NAS2008 / 4008, the default user name is Cam01 up to Cam08 for each of
the 8 user accounts; for GV-NAS2016 / 4016, the default user name is Cam01 up to
Cam16 for each of the 16 user accounts. The default passwords are all 12345678.
For details, see GV-NAS System Quick Start Guide and User’s Manual.
In the NAS Setup window (Figure 3-5), select a camera, select a NAS folder and click .
The new storage path is immediately assigned. Alternatively type the storage path, ID and
password of a NAS folder. Click Save to apply the settings.
1. In the NAS Setup window (Figure 3-5), select a camera and its storage path, and click
the Delete the selected storage path button.
Figure 3-10
27
Chapter 4 Live View
You can utilize GV-Edge Recording Manager to manage multiple live views and their
recording status.
3 5
2 4 6
Figure 4-1
1. Live View Displays the live video stream of the camera channel.
28
4 Live View (Windows Version)
4. Wave Out Receives live audio from the current live view.
Note:
1. To view the dewarped image of GV-VR360 on GV-Edge Recording Manager V1.3.0.0
or later, the graphic card must support DirectX 10.1 or above.
2. Up to 2 GV-VR360 can be connected to a GV- Edge Recording Manager with a total
frame rate of 24 fps.
29
Functions on Live View and Host List
The live view screen can be controlled using the actions below.
Actions Functions
In the Host List (Figure 1-3), right-click a camera channel, from a host, to access the
following options, when enabled or supported:
Option Functions
Focus View Setup Creates up to 7 close-up views for the camera. (See 4.2.2 Setting
Focus View)
PTZ Setup Enables PTZ functions. (See 4.6 Panoramic PTZ View later in this
chapter)
Fisheye Option Opens the Fisheye Settings dialog box for GV-Fisheye Cameras.
(See 4.5 Fisheye View)
Remote ViewLog Accesses the Remote Playback window for playing back recordings
of the host selected. (See Chapter 6 Playback)
1. In the Layout List, click Add and click Add New Layout. This dialog box appears.
Figure 4-2
2. Name the new layout and select one of the three available methods under Layout Setup
to define a layout and click OK.
3. If you select Customize in the step above, the Customize Layout dialog box appears.
30
4 Live View (Windows Version)
You can create up to 7 close-up views per camera and place these created close-up views
inside the live view grid.
1. In the Host List, right-click a camera channel from a host and select Focus View Setup.
This dialog box appears.
Figure 4-3
2. Click Enable and draw a box on the camera view to create a focus view. You can create
multiple focus views if needed.
3. Click OK. The created focus views are listed under the camera.
Figure 4-4
4. Drag the focus views to live view grids.
Note: This function is not supported by Fisheye Cameras and PTZ Cameras.
31
4.2.3 Setting a Scan Window
You can assign multiple cameras to a Scan Window, and each camera will be shown in
sequence for the Scan Interval specified.
1. In the Layout List, select Windows, and drag Scan Window to a live view grid.
2. Drag multiple cameras into the Scan Window.
Figure 4-5
3. Move the cursor to the Scan Window, click Tools , and select Properties. This dialog
box appears.
Figure 4-6
32
4 Live View (Windows Version)
4. To adjust the order of a camera, select a camera and click the Up and Down
arrows.
5. To specify how many seconds to show the live view of each camera, click and adjust
the Scan Interval of each camera. Optionally click to apply this Scan Interval to all
cameras.
6. To show camera name on live view, select Show Caption.
7. To lock the original aspect ratio of the camera image, select Keep Image Ratio.
8. Click OK.
33
4.3 Enabling Host Recording
You can remotely enable/disable monitoring on the connected host.
Note:
1. This function is only supported by GV-DVR / NVR / VMS, GV-IP Cameras (except
GV-ABL / ADR / AVD / EBD / TBL / TDR / TVD series, GV-SD2322-IR / 2722-IR /
3732-IR).
2. For GV-DVR / NVR / VMS, make sure of the account used for connecting to GV-Edge
Recording Manager having the privilege to enable monitoring.
From the Live View Window, click Configure on a camera’s live view (No. 6, Figure 4-1)
and select Monitor. The status of a camera channel is indicated as below:
Channel Color Monitoring & Recording Status
Not monitoring
Monitoring but not recording
Monitoring and recording
Figure 4-7
34
4 Live View (Windows Version)
1
Figure 4-8
35
4.5 Fisheye View
A fisheye camera allows you to cover all angles of a location with just one camera. The
circular fisheye view can be dewarped into the following four view modes, and you can drag
PTZ views to different angles.
Note: This function requires a graphic card supporting DirectX 10.1 or later.
Quad view: 4 PTZ views 360 degree: 2 PTZ view & 1 360º view
36
4 Live View (Windows Version)
1. To display the dewapred view, from the Host List, drag the fisheye camera (circular
source image) or one of the dewarpped views to the live view grid.
2. To change the dewarped settings, right-click the fisheye camera from the Host List >
Fisheye Option. The Fisheye Setting window appears.
Figure 4-10
3. Right-click on the Fisheye Settings window > Fisheye Option to access the following
settings:
360 degree: Composed of two PTZ views and one 360º panoramic view.
Single view: Composed of one PTZ view. This view mode supports the
advanced Picture-in-Picture (PIP) function, which allows you to have a close-
up view without missing the entire view of surveillance site.
◼ Adjust Auto Pan Speed At Top-Left Channel: Select low, medium, or high speed
to enable Auto Pan for the PTZ view at the rotation speed of your choice. This
option is only available in Quad view, 360 degree and Single view.
◼ Zoom: Select Zoom In or Zoom Out and then click on the image.
◼ Show Source Video At Top-Right Channel: Display the circular source image in
the top-right quadrant when Quad view is selected.
37
◼ 360 Object Tracking: Only available in 360 degree view. Track and highlight
detected motion in live view. For details, see 4.5.2 Object Tracking.
◼ Guard Tour Setting: Only available in Single View mode. Enable to set up a
virtual PTZ tour using the defined preset points on live view. For details, see 4.5.3
Virtual PTZ Tour.
◼ Settings:
Figure 4-11
Wide View: Increases the height of the 180-degree view when camera
position is set to wall mount.
Figure 4-12-1: Wide View Disabled Figure 4-12-2: Wide View Enabled
Frame Rate Control: Limits the frame rate of the fisheye live view to a
specified rate. Select Apply All to apply the frame rate to all fisheye views.
4. Drag the dewarped fisheye views from the Host List to live view grids for display. You can
drag and drop PTZ view or 180 degree view to adjust the viewing angle.
38
4 Live View (Windows Version)
Figure 4-13
1. Set the fisheye view to 360 degrees by following Step 1 & 2 in 4.5.1 Setting up Fisheye
View and selecting Camera Mode > 360 degree.
39
2. On the Fisheye Settings window, right-click the fisheye view > Fisheye Option > 360
Object Tracking > Advanced Settings. This dialog box appears.
Figure 4-14
◼ Mask Region: Use the mouse to outline a mask region where motion is ignored.
◼ Object Size: Click the button to pause the live view and then use the mouse to
outline the maximum and minimum size of the target object.
◼ Dwell Time of Motion: When the target object stops moving, the highlighted region
and the top-right channel will remain fixed for the number of seconds specified. Any
new motion detected during the dwell time is ignored to prevent the camera view from
frequently jumping from one region to another.
3. To enable object tracking, on the Fisheye Settings window, right-click the fisheye view >
Fisheye Option > 360 Object Tracking > Tracking.
40
4 Live View (Windows Version)
1. Set the fisheye view to Single view by following Step 1 & 2 in 4.5.1 Setting up Fisheye
View and selecting Camera Mode > Single view.
2. Right-click the fisheye camera on the Host List > Fisheye Settings. The Fisheye
Settings window appears.
3. Right-click the fisheye view on the window > Fisheye Option > Guard Tour Setting.
The Guard Tour Setting dialog box appears along with the Fisheye Settings window.
4. On the Fisheye Settings window, move the live view to a desired starting point for the
PTZ tour by clicking on the inset window at the bottom right.
5. Enable the settings, type a name for the current view and click Add. This view point
(preset point) appears under Preset ID.
Figure 4-15
6. Specify the duration for the live view to stay on this preset point (dwell time). The default
is 10 seconds.
41
9. To add more preset points, repeat the steps above.
10. To change the order of the preset points, use the View Order drop-down list to move a
preset point up or down the list.
12. Select OK to start the PTZ tour. To stop the PTZ tour, disable the function on the Guard
Tour Setting.
To do this:
1. Drag both the fisheye and PPTZ camera channels from the Host List onto the Live View
window.
2. Click on any place on the fisheye view. The speed dome will automatically point to the
designated area.
Figure 4-16
42
4 Live View (Windows Version)
1. On the Live View window, click Configure on the camera’s live view, enable Wide
Angle Lens Dewarping.
3. Move the slider at the bottom to correct the degree of warping. The adjusted view is
shown on the right.
Figure 4-17
4. To apply this dewarping setting to other channels on the Live View window, select Apply
All.
5. To apply the dewarping setting to a single camera channel, click Configure on the
camera’s live view and select Wide Angle Lens Dewarping. The selected channel is
adjusted accordingly.
43
4.8 Enabling QView Display
When having at least two monitors connected to your computer, you can project a live view
display onto another monitor using the QView function and view a live view on a separate
monitor as full screen.
5 7
Monitor 1 Monitor 2
Figure 4-18
1. On the main screen, click Configure (No. 5, Figure 1-2) and select Setup . The System
Configure dialog box appears.
2. Click the Live View tab and select QView. Select Monitor 2 and click OK.
Figure 4-19
3. Click the single live view you wish to project onto another monitor. The live view is
displayed onto the monitor selected.
Note: GV-Edge Recording Manager and the QView’s setting cannot be applied on the
same monitor.
44
5 Audio Communication (Windows Version)
Move the cursor on the live view of a camera and select the following options:
Tip: Right-click GV-VMS from the Host List and select Microphone / Way Out / 2 Way.
45
Chapter 6 Playback
You can remotely play back recordings from the connected hosts on GV-Edge Recording
Manager.
⚫ Playback Window: To play back from any time period within the host’s timeline, using
the Playback window, see 6.1 The Playback Window.
Note:
1. The Instant Playback (No. 2, Figure 4-1) and audio recording backup are not
supported by GV-SNVR.
2. Remote playback from SD card is not supported for the following models: GV-ABL /
TBL Series, GV-ADR / TDR Series, GV-AVD / TVD Series, GV-EBD Series, GV-
QSD5730 / 5731-IR, GV-SD2322-IR / 2722-IR / 3732-IR, UA-B580F3 / R500F2 /
R560F2 / R580F2 / R800F2.
3. For a GV-DVR / NVR / VMS host, make sure Remote ViewLog Service (under
Control Center Service) is enabled to allow GV-Edge Recording Manager to remotely
access the host for playback.
Right-click a host/camera from the Host List and select Remote ViewLog.
Figure 6-1
46
6 Playback (Windows Version)
Select Playback at the top of the main screen, and drag a host device or camera
from the Host List into the playback window.
Figure 6-2
Tip: You can customize the number of channels and layout for playback using the Layout
function on the left panel.
2. On the timeline, click the arrows or click on the date to select a date with recordings,
which are highlighted in blue, from a pop-up calendar.
Calendar
Date/Calendar
Camera Name
Playback Time
Figure 6-3
47
3
6
1 4 5
Figure 6-4
48
6 Playback (Windows Version)
Timeline Player
Calendar
Focused Camera
Playback Time
Playback Mode
A to B Mode Update the timeline
Previous Frame Audio
Playback Speed
Rewind
Next Frame
Play / Pause
Figure 6-5
49
Tip: Right-click on the timeline and drag a period of recording time to have a quick access
to the following functions: Backup, Save as AVI, Object Search, Delete (recording files),
Mark / Unmark Never Recycle.
By default, The Playback Window is set to play back video in the Real Time mode. To
change playback modes, click on the Timeline Player.
◼ Frame by Frame (without audio): Plays back video frame by frame without audio;
however, playback can be delayed depending on the bandwidth and computer
performance.
◼ Real Time: Plays back video on real time. Despite saving rendering time, this method
drops frames.
A to B Playback Mode
When playing back videos, you can set a start and an end frame for auto-playing:
1. To set the start frame, click and double-click a time on the timeline.
2. To set the end frame, click and double-click a time on the timeline.
3. The start time and end time are displayed besides A and B as illustrated below.
Figure 6-6
4. Click to start playing back from frame A to B repeatedly.
5. To cancel this playback mode, click
50
6 Playback (Windows Version)
You can directly drag the timeline to search and view recordings of a previous or next day
with recorded events.
1. Scroll the mouse wheel forth to enlarge the timeline. The default display of the timeline is
24 hours.
2. Click and drag the timeline back and forth. The timeline jumps between the recording
days.
Figure 6-7
Note:
1. Only the Defog, Stabilizer, Fisheye and Download features are supported in GV-
SNVR and GV-NAS System.
2. The Play Speed option is not supported in GV-SNVR.
3. The Heat Map feature is only supported for GV-VMS V15.10.1.0 or later.
51
Chapter 7 System Configuration
This chapter describes GV-Edge Recording Manager’s startup mode, windows and dialog
box layout and port settings.
Figure 7-1
[Startup]
◼ Autorun When Windows Starts: GV-Edge Recording Manager starts up when
Windows is started.
[Layout]
◼ Always On Top: Each newly opened window or dialog box will stay on the top of other
windows or dialog boxes.
◼ Show Style: Select a theme color for the interface.
52
7 System Configuration (Windows Version)
Figure 7-2
◼ Wave out When Zoomed: Automatically receives live audio from the surveillance site
when zooming in on its live view, when available.
◼ Enable DirectDraw: Enhances the coloring to have more vivid and saturated images.
Some VGA cards might not support DirectDraw and can produce distorted frames. In this
case, disable the feature.
◼ Enable GPU: Enabled by default, uses GPU decoding for image decoding to reduce
CPU loading.
◼ VMS Video Quality: Selects the quality of the camera images from VMS hosts. Higher
the quality, the more network bitrate required.
◼ QView: Projects a live view display onto another monitor when you have at least two
monitors connected to the PC, see 4.8 Enabling QView Display.
53
7.3 Exporting and Importing Settings
1. On the main window, click Configure (No. 5, Figure 1-2) > Export Data. This dialog box
appears.
Figure 7-3
2. Set up a password for the exported settings. This password is required when the settings
are being imported.
3. Click OK to confirm. Select a storage location and modify the file name if necessary.
4. Click Save.
1. On the main window, click Configure (No. 5, Figure 1-2) > Import Data. A notification
message appears.
2. Click Yes to confirm. Locate a previously backed-up file and click Open. The password
request appears.
54
Chapter 8 Authentication Server
GV-Edge Recording Manager can integrate with the Authentication Server to access a
specified group of GV-DVR / NVR / VMS hosts and thus the connected cameras of these
hosts, through an Authentication user account.
For details on the settings of Authentication Server, see 9.4 Authentication Server in GV-
VMS User’s Manual.
Figure 8-1
55
4. Under User Account, type the Account ID and Password created on the Authentication
Server. Optionally select Save Account to enable GV-Edge Recording Manager to
memorize the ID and Password of the Authentication Server.
Figure 8-2
Figure 8-3
6. Click OK. A list of hosts assigned to the user account created on the Authentication
Server will be displayed in the Host List.
56
Appendix
PTZ Control Using GV-Joystick
A 64-CH license is required for using GV-Joystick. The following program must be running in
the background when using GV-Joystick for PTZ for control. For details on GV-Joystick
operations, see GV-Joystick User’s Manual.
1. On the main screen, click Configure > Joystick. This dialog box appears
Figure A
2. In the Device field, select GeoVision Joystick to connect to GV-Joystick V2.
3. Click the Start Service button ► and then you can use GV-Joystick to control the
PTZ camera.
4. If more than one GV-Joystick is connected, repeat Step 2 to set up and use another
GV-Joystick.
57
Mac Version
57
Chapter 9 Overview
9.1 Main Window
1 2 3
Figure 9-1
2 Live View Window Displays live views from hosts. For details, see 12.1 The Live
View Window.
58
9 Overview
3 4 5 6 7
Figure 9-2
59
9.3 The Toolbar
1 2 3 4 5
Figure 9-3
1 Controller Click to extend the Live View Window (No. 3, Figure 9-1) to
full screen.
2 Event List Displays events with event type, device name and detection
time. For details, see 12.6 Viewing Event List.
3 Remote Playback Click to access the recording calendar which notes dates in
which recordings are done. For details, see Chapter 14
Playback.
4 Setup Click to access the Camera List for host management. For
details, see 9.2 The Camera List.
5 Layout Click to switch the live view division. You can choose among
1, 4, 6, 8, 9, 10, 13, 16, 25, 36 and 64 (with In-App Purchase)
channels.
60
Chapter 10 Getting Started
10.1 Installing GV-Edge Recording Manager
Follow the steps below to install GV-Edge Recording Manager from the GeoVision Website.
3. Click the View in Mac App Store tab. The browser redirects
61
10.2 Adding Hosts
At first startup, GV-Edge Recording Manager automatically searches and displays GV-IP
Devices and servers installed with GeoVision software that are under the same LAN. To add
multiple hosts, follow the instruction in 10.2.1 Automatically Adding Multiple Hosts. To add a
single host, follow the instruction in 10.2.2 Manually Adding a Host.
1. For the first startup, you will be prompted to search GV-IP Devices and servers installed
with GeoVision software that are under the same LAN with GV-Edge Recording
Manager. Click Start to search.
Figure 10-1
2. Click Start and click from the Camera List. The Add Camera window appears and
the searched devices are displayed.
3. To refresh the list, click . GV-Edge Recording Manager starts browsing for GV-IP
Devices under the same LAN and the found devices are immediately listed.
Figure 10-2
62
10 Getting Started
A. Select hosts from the Add Camera window or click Select All to add all the hosts.
B. Type the username and Password and click Apply All to log in the selected hosts
using the username and password or type the Username and Password for each
camera. Click Next.
Figure 10-3
Figure 10-4
63
D. To remove unwanted hosts, click Back to return to the previous step to unselect
them. To add these hosts to Camera List, click Apply. They are immediately added.
Figure 10-5
5. You can display live view using any of the following method:
Double-click a host
Note:
1. If a router or firewall is installed, ensure the following communication ports required by
the Host Search function are open:
TCP/IP ports 5201 (for searching GV-VMS) and 5202 (for searching GV-IP
Devices)
Multicast port 5200
2. If antivirus software is installed, the Host Search function may be interfered and will not
detect the available hosts. In this case, turn off the antivirus software and try again.
3. To add GV-VMS hosts, make sure that Mobile Service is enabled ahead to allow
remote access from GV-Edge Recording Manager. (Network button > Mobile Service)
Figure 10-6
64
10 Getting Started
1. Click from the Camera List. The Add Camera window appears.
Figure 10-7
3. Type the host’s device name, IP address, username and password. The default
command port is 10000 for GV-IP Devices, 56000 for GV-VMS, 11000 for GV-
Recording Server, and the default HTTP port is 80. Only modify these values if
necessary.
4. Optionally click to obtain a list of cameras that are connected to the host. This
function only applies to GV-VMS and GV-Recording Server which contain multiple
cameras.
65
5. Select the cameras to be added and then click Next. This page appears.
Figure 10-8
6. Click Apply. These cameras are added to the Camera List.
Figure 10-9
66
Chapter 11 Batch Management
The batch functions are integrated interfaces designed for management of mass number of
GV-IP Devices without the need to visit each device’s Web interface. On these interfaces,
you can change/assign IP address, rename devices, assign NAS and view storage space
information of multiple GV-IP Devices.
Note:
1. The batch management functions described in this chapter are only supported by GV-
Video Server and GV-IP Cameras (except GV-ABL / ADR / AVD / EBD / TBL / TDR /
TVD series, G-SD2322-IR / 2722-IR / 3732-IR).
2. By default, all the usernames and passwords for batch management functions (under
Utilities) are admin. To use a different username and password, type in the Username
and Password fields.
Figure 11-1
1. On the main screen, move the cursor to the top, from the emerging toolbar, click Tools
and then click Utilities. The Utilities window appears.
Figure 11-2
67
2. Click to browse for GV-IP Cameras under the same LAN. The devices found are
listed.
Figure 11-3
3. Select at least one device, type the Start IP address, subnet mask, default gateway,
DNS, username and password. For multiple devices, the IP address will proceed from
the start IP address you specified.
4. To preview the new IP addresses, click Auto Assign. The IP addresses to be assigned
are shown in the New IP column.
Figure 11-4
68
11 Batch Management
5. Click Apply to start the update. When update is completed, the “Success” message
appears in the State column.
Figure 11-5
69
11.2 Renaming Devices
You can modify the device name for multiple devices through a single interface, without
visiting each device’s settings page.
1. On the main screen, move the cursor to the top, from the emerging toolbar, click Tools
and then click Utilities. The Utilities window appears.
Figure 11-6
2. Click to switch to the Camera Name page and then click to browse for GV-IP
Cameras under the same LAN. The cameras found are listed.
Figure 11-7
70
11 Batch Management
3. Type the new device name in the New Name column, username and password and
then click Apply to start the update. When the update is completed, the “Success”
message appears in the State column.
Figure 11-8
71
11.3 Viewing Storage Information
You can view the free and total storage space on this page.
Note: This function is only available for GV-IP Devices. For the supported firmware
version, see Supported GV-GeoVision Products in Introduction of this manual.
1. On the main screen, move the cursor to the top, from the emerging toolbar, click Tools
and then click Utilities. The Utilities window appears.
Figure 11-9
Figure 11-10
72
11 Batch Management
4. Click an HDD entry to view the device’s free and total storage. This information is only
accessible for devices with valid username and password.
Figure 11-11
73
11.4 Assigning NAS Storage for Recording
You can record multiple GV-IP Cameras and GV-Target Cameras to NAS through GV-Edge
Recording Manager.
IMPORTANT:
1. For the NAS application, it is required to use GV-IP Cameras (firmware V3.00 or
later) and GV-Target Cameras (firmware V1.02 or later), GV-
EFD2101/EFD3101/EVD2100/EVD3100 (firmware V1.00 or later).
2. For system performance and compatibility, it is highly recommended to use GV-NAS
Systems for recording.
3. Make sure the computer installed with GV-Edge Recording Manager is under the
same LAN with the NAS.
1. On the main screen, move the cursor to the top, from the emerging toolbar, click Tools
and then click Utilities. The Utilities window appears.
Figure 11-12
Figure 11-13
74
11 Batch Management
3. Type the username and password of the cameras you wish to search and click to
browse. In this example, we search for cameras with the username and password
admin. This dialog box appears.
Figure 11-14
4. Select a camera and click to browse for NAS servers under the same LAN.
Figure 11-15
75
5. To assign the storage path, follow the steps below.
B C
B
Figure 11-16
B. Select a NAS server from the bottom list and type the administrator username and
password of the NAS server. For GV-NAS Systems, the default username and
password are both admin.
76
11 Batch Management
6. Click to assign this path to the camera. The storage path appears immediately in
the SMB Path column.
Figure 11-17
7. Type the username and password of an established account in the NAS server. For
example, the default username and password for a GV-NAS System is Cam01 and
12345678.
Cam01
Figure 11-18
Note:
1. Be sure that you assign each IP camera to record to a different user account in GV-
NAS Systems to avoid disrupting the recycling process.
2. For GV-NAS2008 / 4008, the default user name is Cam01 up to Cam08 for each of the
8 user accounts; for GV-NAS2016 / 4016, the default user name is Cam01 up to
Cam16 for each of the 16 user accounts. The default passwords are all 12345678. For
details, see GV-NAS System Quick Start Guide and User’s Manual.
8. To assign a different recording path for another camera, follow steps 6 and 7.
77
Chapter 12 Live View
You can utilize GV-Edge Recording Manager to manage multiple live views and their
recording status.
Figure 12-1
Use any of the following method to display live view on this window:
Drag and drop cameras from the Camera List (Figure 9-2).
Double-click a camera from the Camera List (Figure 9-2) and double-click again to
disconnect.
Select a device from the Camera List (Figure 9-2) and click .
78
12 Live View
To connect the first 64 cameras, move your cursor to the top of the main screen, from
the emerging toolbar, click Tools and then click Connect to All.
Figure 12-2
Select a device from the Camera List (Figure 9-2) and click .
To disconnect all cameras on the live view, move your cursor to the top of the main
screen, from the emerging toolbar, click Tools and then click Connect to All.
Figure 12-3
Tip:
1. Double-click a channel to display it in full screen and double-click the channel again to
resume the current division setting.
2. If you do not have all the live views displayed on one channel, scroll your mouse to
view more live views.
79
Right-click the live view to access the following features:
No. Name Description
3. Rotation Displays the live view rotated at 0°, 90°, 180° and 270°.
8. Time Synchronize Synchronizes the device time with GV-Edge Recording Manager.
Dewarps the fisheye view. This function is only available for GV-
11. Fisheye
Fisheye Camera. For details, see 12.3 Fisheye View.
12. Disconnect Disconnects the device and removes its live view.
80
12 Live View
Figure 12-4
Figure 12-5
81
12.3 Enabling Host Recording
You can remotely enable/disable monitoring on the connected GV-IP Cameras.
Figure 12-7
82
12 Live View
On the main screen, move the cursor to the top, from the emerging bar, select Tools and
then select Start All Monitoring. To disable monitoring, select Tools again and then select
Stop All Monitoring.
Figure 12-8
83
12.4 Taking Snapshots
You can take snapshot of live view images. Right-click a live view on the Live View Window
(Figure 11-1) and select Snapshot. The snapshot is immediately saved and a message
appears at the top-right corner of the Live View Window. By default, snapshots are saved to
/user/<username>/Documents/GeoVision/edge_record_mgr/snapshot. To configure the
storage path for snapshots, see Snapshot Folder in 15.1 General Settings.
Figure 12-9
84
12 Live View
Note:
1. Make sure that the motion detection function is enabled ahead for each GV-IP
Camera, GV-Target Camera, GV-SD220/220-S and GV-Video Server.
2. GV-VMS is not supported for this function.
Figure 12-10
85
12.6 Fisheye View
The hemispherical image of a fisheye host can be converted to a conventional rectilinear
projection and displayed on the Live View Window.
You can choose among four view modes and adjust the PTZ views to different angles.
PTZ: 1 PTZ view Panorama 360: 2 PTZ view & 1 360º view
86
12 Live View
1. Right-click the live view and select Fisheye to enable the dewarped view. By default, the
original hemispherical view is converted to the PTZ view.
Fisheye Alignment: Aligns the center and part for live view display. Double-click the
channel to display it in full screen first before alignment. Unselect this option when
alignment is set.
Panorama 360: Composed of two PTZ views and one 360º panoramic view.
Mount Type: Select Ceiling, Wall or Ground according to where the camera is
mounted.
3. You can drag and drop any PTZ view to adjust the viewing angle. Display the channel in
full-screen to allow for drag-and-drop control.
87
Chapter 13 Audio Communication
You can receive sounds from a selected host. Right-click a channel and select Audio. The
function is immediately enabled and a speaker icon appears on the channel.
Figure 13-1
88
14 Playback
Chapter 14 Playback
You can remotely play back host recordings on GV-Edge Recording Manager.
Note:
1. For a GV-DVR / NVR / VMS host, make sure Remote ViewLog Service (under
Control Center Service) is enabled ahead to allow remote access from GV-Edge
Recording Manager for playback.
2. Audio playback is not supported by the Mac version of GV-Edge Recording Manager.
1. Click the Playback button on the main window. The Playback page appears.
2. Select a device from the left. A calendar appears below.
3. Click to select a date for playback. Recordings of the selected date are listed (if any).
On AVI Player: The current date is underlined in green and the selected date blue.
On MPEG4 Player: The current date is underlined in green, the selected date blue
and dates with recordings are circled red.
Figure 14-1
89
[MPEG4 Player]
Files saved on GV-NAS Systems are played back by the MPEG4 player.
1
2
Figure 14-2
Figure 14-3
90
14 Playback
Name Functions
91
Chapter 15 System Configuration
This chapter describes GV-Edge Recording Manager’s general settings, panel settings and
network settings.
Figure 15-1
Figure 15-2
92
15 System Configuration
Snapshot Folder: Specifies the storage path for snapshots. By default, snapshots
are saved to /user/<username>/Documents/GeoVision/edge_record_mgr/snapshot.
You can type the storage path in the blank or click to select a folder.
PTZ Speed: Specifies the PTZ speed for PTZ control panel.
Digital PTZ Speed: Specifies the speed for digital pan, tilt and zoom. Under single
channel display, you can scroll to zoom the live view and then drag and hold to see
different parts of the live view.
Keep Video Aspect Ratio: Displays live view in ratio with its current resolution.
Auto Change Video Stream: Displays stream 1 on live view when the source video
exceeds the specified Width and Height. By default, this function is enabled and the
Weight and Height are both 400 pixels.
Ask Auto Scan: Prompts the user to search and add GV-IP Devices at startup (of
GV-Edge Recording Manager) when the Camera List (Figure 9-2) is empty.
Show Live Grid Title: Shows the device name on live view
Show Live Grid Timestamp: Shows the device time on live view
93
15.2 Live View Color Settings
You can define the color of grid background, video background and video border, grid title
hud color, grid animation speed, grid animation type and scroll speed.
On the main screen, move the cursor to the top, select Edge Recording Manager, select
Preferences and then click . This page appears. Click each option or move the slider bar
to change the settings.
Figure 15-3
94
15 System Configuration
On the main screen, move the cursor to the top, select Edge Recording Manager, select
Preferences and then click . This page appears.
Figure 15-4
Network Interface: Click arrow button to select a network card. To update the
network card options, click Refresh.
95
15.4 Exporting and Importing Settings
1. On the main window, move the cursor to the top, from the emerging toolbar, select File
and then select Export. This window appears.
Figure 15-5
3. Click Save.
96
15 System Configuration
1. On the main window, move the cursor to the top, from the emerging toolbar, select File
and then select Import. This window appears.
Figure 15-6
2. Select a previously saved file and click Open. The settings are immediately applied.
97
Specifications
For specifications, see details in:
Datasheet GV-Edge Recording Manager (Windows Version)
Datasheet GV-Edge Recording Manager (Mac Version)
Comparison Chart for GV-Edge Recording Manager Versions
98