Scribd Logo
Upload

Welcome to Scribd!

  • 231 views

    Betamate 2090

    Uploaded by

    José Antonio Cubero

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Betamate 2090

    Uploaded by

    José Antonio Cubero
    231 views4 pages

    Original Title

    BETAMATE 2090

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    231 views4 pages

    Betamate 2090

    Uploaded by

    José Antonio Cubero

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    Technical Datasheet

    BETAMATE™ 2090
    Crash resistant 2-Component Structural Adhesive

    Description / Application:
    BETAMATE™ 2090 is a two component glass beads containing epoxy based adhesive especially developed for
    applications on which a high glass transition temperature and a quick curing is required. The adhesive is used in
    the car to increase the operation durability, the crash performance and the body stiffness.

    Properties:
    Excellent adhesion to automotive steels, including coated steels (e.g. e-coated or organic coated steel) and
    pretreated aluminum
     A high glass transition temperature
    Fast curing Hand free after approx. one hour
     Helps to increase or restore the stiffness and the crash stability of the entire car body
     High durability of the adhesive and the adhesive bond
     Due to its sealing capability the metal and weld points are protected against corrosion
     Compatible with other mechanical and thermal joining techniques

    Application:
    The product is cold pumpable and applicable as a bead (mixing ratio 2:1; static or dynamic). It can be applied with
    the following parameters:

    application speed Up to 300 mm/s

    temperatures: recommended:
    follower plate cold
    follower plate - doser cold
    nozzle cold

    For an optimum tack of the adhesive, the parts to bond should be stored at 15°C or higher. In case of an application
    break longer than 20 minutes the mixer should changed.

    All Dow Automotive products are primarily developed in co-operation with the automobile
    manufacturers, according to their needs and their specifications; they are approved for the specific
    applications as defined by the customer.

    The use of the product other than approved application have to be released in written form by the
    Technical Service of Dow Automotive.

    Dow Europe GmbH, issue 27.03.2015, Page 1


    Technical Data:
    Basis component A: epoxy resin / component B: polymeric amines

    Colour A: blue / B: white

    Density (23°C) 1.12 g/ml

    Mixing Ratio A:B = 2:1

    Viscosity/Yield Point component A: 70 Pas / 230Pa


    (23°C, Bohlin, Casson) component B: 30 Pas / 200 Pa

    Time to Handle approx. 20 min.

    Curing Condition ambient temperature: after 1 day 90% of end toughness


    temperatures up to 180 °C feasible

    Standard Curing 60°C / 2 hours, 1 day at room temperature


    (Drive away strength after approx. 3 hours)

    Tensile Strength (DIN EN ISO 527-1) 30 MPa

    Elongation at Break approx. 6 %


    (DIN EN ISO 527-1)

    E-Modulus (DIN EN ISO 527-1) 1900 MPa

    Glass Transition Temperature


    (DMA torsion test 1Hz) 100°C
    after standard curing

    Lap Shear Strength (DIN EN 1465)


    (CRS 14O3, 1,5mm)
    (Adhesive layer thickness: 0.2 mm
    Bonded area: 25x10 mm)
    2 hours RT 0.5 MPa
    3 hours RT 5.0 MPa
    2 hours 60°C 25 MPa
    (Aluminium 6060T-6 alloy 2,0mm)
    (Adhesive layer thickness: 0.2 mm
    Bonded area: 25x10 mm) 22 MPa
    2 hours 60°C

    T-Peel Strength (DIN EN ISO 11339) 3,5 N/mm


    (Aluminium 5754)
    (Adhesive layer thickness: 0.2 mm
    Bonded area: 25x100 mm
    Standard curing recording Aston Martin)

    Impact Peel Strength (ISO 11343)


    14 N/mm
    (CRS 14O3, 1,0mm)
    (Adhesive layer thickness: 0.2 mm
    Bonded area: 20x30 mm
    Standard curing recording Aston Martin)

    Dow Europe GmbH, issue 27.03.2015, Page 2


    Bonding Surface Preparation Oily surfaces should be cleaned

    Application Tool Cartridges:


    side by side cartridge: hand-operated gun with mechanical
    piston: Mixpac DM 200-01.
    Single cartridge (components one after another): Application
    with a standard 1-component hand-operated or pneumatic
    gun with piston bar (no direct air guns !).
    1-component battery guns may be used, if they are equipped
    with adjustable feed.

    Drums, pails: With standard 2K-based systems

     If BM 2090™ is applied out of cartridges it is necessary to


    Application notes
    equalize the filling levels.
     For the best performance it is recommended to reject the
    first few grams of mixed adhesive.
     During the storage time a crystallization of the resin may
    occur. By heating the adhesive to 40 - 50 °C for about 15 to
    30 minutes this physical process is reversible. All properties
    stay on the same level.
     Before the application the material temperature of both the
    resin and the hardener should be at min. 15°C.

    Cleaning Uncured material can be removed with BETACLEAN 3510.


    Attention: The contact with bonded areas should be avoided.

    Drums and Pails: Upon request


    Containers
    2-component cartridges: 195ml two-in-one cartridge

    Shelf life Storable at temperatures under 30°C for 12 months.

    The given data are standard values.

    Dow Europe GmbH, issue 27.03.2015, Page 3


    Health and Safety:
     Bulk Exothermic Reaction
    The material curing reaction is exothermic. If the material is held in bulk the reaction is accompanied by a
    rapid build-up of exothermic heat. To avoid the risk of this bulk exothermy, containers of the material should
    in no circumstances be heated by e.g. hot plates or simple drum heaters. If heating a bulk quantity of the
    material is considered necessary, advice should be sought.

     Caution
    The adhesive resins are generally quite harmless to handle provided that certain precautions normally taken
    when handling chemicals are observed. The uncured materials must not, for instance, be allowed to come
    into contact with foodstuffs or food utensils, and measures should also be taken to prevent the uncured
    materials, from coming into contact with skin, since people with particularly sensitive skins may be affected.
    The wearing of impervious rubber or plastic gloves will normally be necessary; likewise the use of eye
    protection. The skin should be thoroughly cleaned at the end of each working period by washing with soap
    and warm water. The use of solvents is to be avoided. Disposable paper - not cloth towels - should be used
    to dry the skin. Adequate ventilation of the working area is recommended. For further and more detailed
    precaution measures see the Health and Safety Data Sheet.

    Notice:

    Quality is our utmost goal. Dow Automotive works according to a modern quality management system
    conforming to international standard ISO/TS 16949.
    All sites of Dow Automotive are certified according to ISO 14001.

    All statements, technical information and recommendations contained in this document are based on tests that
    we deem reliable. However, the customer is responsible to determine the suitability of the product for
    customer’s intended purpose. No freedom from any patent owned by Dow or others is to be interfered.

    NO WARRANTIES ARE GIVEN. ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A


    PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED.

    Dow Automotive Systems Main Offices

    The Dow Chemical Dow Automotive Systems Dow Automotive Systems Dow Automotive Systems
    Company World Head Quarter
    Customer Information Dow Deutschland Dow Europe GmbH
    Group Europe 1250 Harmon Road Anlagengesellschaft GmbH Bachtobelstrasse 3
    Auburn Hills, MI 48326 Am Kronberger Hang 4 8810 Horgen
    Phone +800 3 6946367 USA 65824 Schwalbach Switzerland
    Phone +32 3 450 2240 Tel. +1 248 391 63 00 Germany Tel. +41 44 728 2111
    Italia 800 783 825 Fax +1 248 391 64 17 Tel: +49 6196 566 0 Fax. +41 44 728 2935
    Fax +32 3 450 2815 Fax: +49 6196 566 444

    Dow Automotive Systems Dow Automotive Systems Dow Automotive Systems

    Dow Chemical Ibérica, S.L. Dow France S.A.S. Dow Italia Divisione
    Ribera del Loira, 4-6 - Planta 23 avenue Jules Rimet Commerciale s.r.l.
    4ª (Edificio IRIS) 93631 La Plaine St Denis Via F. Albani, 65
    28042 Madrid Cedex 20148 Milano
    Spain France Italy
    Tel. + 34 91 740 7800 Tel: +33 1 49 21 78 78 Tel: +39 02 482 21
    Fax. + 34 91 740 7785 Fax: +33 1 49 21 79 79 Fax: +39 02 482 241 08

    Dow Europe GmbH, issue 27.03.2015, Page 4

    You might also like