0102-Ss-E-Tqu-102 - Circuit Breaker For Line (1 Pole) Technical Particular Guarantee

Download as xls, pdf, or txt
Download as xls, pdf, or txt
You are on page 1of 26

DAFTAR ISIAN 3 : TECHNICAL PARTICULARS AND GUARANTEES

TPG V.3. 2 : 150 KV CIRCUIT BREAKER

NO. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

1. Manufacturer - To be mentioned
2. Type of designation - To be mentioned
3. Type of circuit breaker Operating Mechanism - Spring Type
4. Standard - IEC-62271-100 and IEC-60376
5. Type of arc quenching medium - SF6
6. Number of phases - 3
7. Frequency Hz 50
8. Nominal voltage kV 150
9. Highest system voltage kV 170
10. Rated continuous current A 1250, 1600, 2000, 2500, 3150, 4000
11. Short time current rating (1 seconds) kA 31,5 or 40
12. Symmetrical short circuit (1 seconds, r.m.s.) at
highest system voltage kA 31,5 or 40
13. Short circuit making current 1 seconds, r.m.s.) at
highest system voltage
kA 80 or 100
14. Breaking capacity kA 31,5 or 40
15. Insulation class :

- Power frequency withstand voltage (1 min) kV 325


- Impulse withstand voltage (1.2/50 microsec.
full wave) kVp 750

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE


1 dari 26

(......................................................) (..............................................)
DAFTAR ISIAN 3 : TECHNICAL PARTICULARS AND GUARANTEES

TPG V.3. 2 : 150 KV CIRCUIT BREAKER

NO. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

16. Interrupting time cycle 3


17. Operating duty cycle :
- nominal sequence - O - 0.3s - CO - 3min - CO
- out of phase - O - CO
- autoreclose :
- high speed single phase - O - 0.3s - CO
- high speed three phase - NA
- minimum time between each successive ms 300
make/break operation
18. Opening time :
- without current ms To be mentioned
- at 100% of rated breaking current ms To be mentioned
19. Maximum arcing duration of any duty cycle to ms To be mentioned ......ms at ........%
IEC 62271-100
20. Duty on which maximum arc duration occurs ms To be mentioned
closing time
21. Minimum time for arc extinction to contact ms To be mentioned
remake when adapted for auto reclosing
22. Time from closing of control switch to completion ms To be mentioned
of closing stroke during fault making
23. Amplitude factor - 1.4
24. First pole to clear factor - 1.3
25. Reclosing :
- Incoming/outgoing feeder - 1 and 3 ph
- Transformer feeder - N.A
- Bus-coupler feeder - N.A

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE


2 dari 26

(......................................................) (..............................................)
DAFTAR ISIAN 3 : TECHNICAL PARTICULARS AND GUARANTEES

TPG V.3. 2 : 150 KV CIRCUIT BREAKER

NO. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

26. TRV parameter :


a) Rated transient recovery voltage for terminal kVp To be mentioned
faults at 100% rated short circuit breaking
current Uc
b) Time co-ordinate t2 Us To be mentioned
c) Time co-ordinate t1 Us To be mentioned
d) Time delay td Us To be mentioned
e) Rate of rise kV/microsec. To be mentioned
27. Maximum guaranteed switching overvoltage kV To be mentioned
28. Quantity SF6 gas required kg To be mentioned
29. Creepage distance :
- between terminals mm/kV 25 (heavy)
- between live parts and ground mm/kV 25 (heavy)
30. Minimum clearance in air :
- between phase mm 1800
- phase to earth mm 1500
- across circuit breaker poles mm To be mentioned
- live conductor to ground level mm 3800
- live insulator to ground level mm 2300
31. Period of time the equipment has been in year To be mentioned
commercial operation
32. Supply voltage for motor mechanism / charging Vac 230

33 Control voltage Vdc 110


34 Tolerance range for auxilliary supply voltage (in
% of rated voltage)
- opening coil % 70 to 110
- closing coil % 80 to 110
- motor % 85 to 110

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE


3 dari 26

(......................................................) (..............................................)
DAFTAR ISIAN 3 : TECHNICAL PARTICULARS AND GUARANTEES

TPG V.3. 2 : 150 KV CIRCUIT BREAKER

NO. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

35 Kind of filtering material absorbing the residual - To be mentioned


decomposition products of SF6 gas
36 Material of the quenching chamber - To be mentioned
37 Material of the arc nozzle - To be mentioned
38 Material of the main contacts - To be mentioned
39 Leakage rate of SF6 gas per annum % 1
40 Voltage drop across main contacts per phase at V To be mentioned
rated continuous current
41 Temperature rise of contacts and terminals at °C To be mentioned
rated continuos current

42 Number of switch operations between two


inspections for changing the main-contacts :
- with no load To be mentioned
- with rated continuous current To be mentioned
- with rated breaking current To be mentioned
43 Power consumption for closing per pole W To be mentioned
44 Power consumption for opening per pole W To be mentioned
45 Number of tripping coils unit 2
46 Number of closing coils unit 1
47 Overall dimension of circuit breaker :
- length mm To be mentioned
- width mm To be mentioned
- height mm To be mentioned

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE


4 dari 26

(......................................................) (..............................................)
DAFTAR ISIAN 3 : TECHNICAL PARTICULARS AND GUARANTEES

TPG V.3. 2 : 150 KV CIRCUIT BREAKER

NO. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

48 Necessary environmental conditions for carrying -


out inspections of the circuit breakers
49 Weight of the heaviest part to be handled during kg To be mentioned
general inspections
50 Weight of 3 phase circuit breaker complete with kg To be mentioned
operating mechanism
51 Admissible horizontal pull on the main terminals N To be mentioned
under dynamic short circuit conditions
52 Consideration of earthquake factor - 0.2 g
53 Type and Routine Test Certificates acc. to IEC 62271 To be submitted
54 Catalog, drawing or other references - To be submitted
55 Expert supervision engineer during erection and yes
test & commissioning

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE


5 dari 26

(......................................................) (..............................................)
DAFTAR ISIAN 3 : TECHNICAL PARTICULARS AND GUARANTEES

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR TRAFO BAY AND COUPLE BAY

NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

Manufacturer to be mentioned
Type Designation to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition refer to General Particulars of the site in Book B
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
7 Rated voltage (Ur) kV rms 170
8 Rated frequency (Fr) Hz 50
9 Rated normal current (Ir) A rms ≥ (1250 or 2000 or 2500 or 4000)
10 Rated short-time withstand current (I th) kA rms 31,5 or 40 or 50
11 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
12 Rated duration of short circuit s ≥ 1
13 Rated insulation level :
Power frequency withstand voltage, dry for 1 minute
Phase to earth, between the phases and across the open
kV rms 325
breaker gap
Impulse withstand voltage (at 1,2/50 microsecond)
Phase to earth, between the phases and across the open
kV peak 750
breaker gap
Minimum Creepage distance (according to degree of
14
pollution)
a) Up to Heavy Pollution mm/kV 25
b) Very Heavy Pollution mm/kV 31
15 Operating Sequence And Operating Duty
- Nominal Sequence
(Not intended for rapid auto reclosing) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
16 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms 31,5 or 40 or 50
- % dc component % dc > 20
17 Breaking current under out of phase condition kA rms ≥ 25 % x I th

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

6 dari 26

(......................................................) (..............................................)
DAFTAR ISIAN 3 : TECHNICAL PARTICULARS AND GUARANTEES

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR TRAFO BAY AND COUPLE BAY

NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

18 Rated capacitive switching currents for Line charging refer to IEC


Radio influence voltage level, measured at 1.1 Ur/√3 at 1
19
Mhz
- circuit closed to ground µV To be Mentioned
- circuit breaker open, grounded terminal µV To be Mentioned
20 Classes
- Electrical endurance E1
- Transient Recovery Voltage N/A
- Mechanical endurance M2
- Restrike performance C2
23 Temperature rise at :
- Contacts in SF6 °C ≤ 65
- Connection, bolted or equivalent in SF6 °C ≤ 75
- Terminal °C ≤ 65

MECHANISM
Manufacture
Type
24 Number of interrupters in series per phase pcs 1
25 Number of tripping coils per phase pcs 2
26 Number of closing coils per phase pcs 1
27 Operating mechanism :
- Type spring
- Number of stored energy operation 1 ( one for three phase)
28 Protection level of control cubicle IP54
29 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230/400 V AC
- Heater Volt AC 230 VAC
30 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
- motor % 85 to 110
31 Mechanical performance

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

7 dari 26

(......................................................) (..............................................)
DAFTAR ISIAN 3 : TECHNICAL PARTICULARS AND GUARANTEES

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR TRAFO BAY AND COUPLE BAY

NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

1. Total break time (trip initiation to final arc extinction) ms ≤ 50


2. Opening time (trip initiation to contact separation) without
ms ≤ 30
current
3. Time interval between opening of interrupters of first and
ms ≤4
last phase
4. Time interval between opening of interupters of one
ms N/A
phase
5. Making time without current ms ≤ 100
6. Time interval between closure of interrupters of the first
ms ≤ 10
and last pole
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
32 Number of auxiliary contacts (NO/NC) per pole pcs >8

OTHERS
34 Discrepancy device N/A
35 Antipumping device Yes
36 Method of controling voltage distribution between break unit N/A
37 Method of Closing control N/A
38 Value of closing resistor Ohm N/A
39 Insertion time of closing resistor ms N/A
40 SF6 Pressure Indicator per set pcs 1
41 Counter to record number of operation per set pcs 1
Seismic acceleration constant consideration (according to
42 g 0,2 or 0,3
seismic map)
43 Leakage rate of SF6 gas per annum % ≤ 0.5
44 Contact resistance across main contacts per phase µ ohm < 100
Number of switch operations between two inspections for
45
changing the main-contacts :
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
47 Material of insulator Silicon Rubber or Porcelain
48 Minimum clearance in air :
- between phase mm 1800
- phase to earth mm 1500
- live conductor to ground level mm 3800

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

8 dari 26

(......................................................) (..............................................)
DAFTAR ISIAN 3 : TECHNICAL PARTICULARS AND GUARANTEES

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR TRAFO BAY AND COUPLE BAY

NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

- live insulator to ground level mm 2300

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

9 dari 26

(......................................................) (..............................................)
#REF!

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR LINE BAY

NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

Manufacturer to be mentioned
Type Designation to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition refer to General Particulars of the site in Book B
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
6 Rated voltage (Ur) kV rms 170
7 Rated frequency (Fr) Hz 50
8 Rated normal current (Ir)
a) up to twin conductors A rms ≥ 1600
b) quadruple conductors A rms ≥ 3150
9 Rated short-time withstand current (I th) kA rms 31,5 or 40 or 50
10 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
11 Rated duration of short circuit s ≥ 1
12 Rated Insulation Level :
Power frequency withstand voltage, dry for 1 minute
Phase to earth, between the phases and across the open
kV rms 325
breaker gap
Impulse withstand voltage (at 1,2/50 microsecond)
Phase to earth, between the phases and across the open
kV peak 750
breaker gap
13 Minimum Creepage distance (according to degree of pollution)
a) Up to Heavy Pollution mm/kV 25
b) Very Heavy Pollution mm/kV 31
14 Operating Sequence And Operating Duty
- Nominal Sequence
(rapid auto-reclosing/dead time) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
15 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms 31,5 or 40 or 50
- % dc component % dc > 20

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

10 dari 26

(......................................................) (..............................................)
#REF!

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR LINE BAY

NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

16 Breaking current under out of phase condition kA rms ≥ 25 % x I th


Rated capacitive switching currents for Line charging or Cable
17 A rms refer to IEC
charging
18 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz
- circuit closed to ground µV To be Mentioned
- circuit breaker open, grounded terminal µV To be Mentioned
19 Classes
- Electrical endurance E1
- Transient Recovery Voltage N/A
- Mechanical endurance M2
- Restrike performance C2
20 Temperature rise at :
- Contacts in SF6 °C ≤ 65
- Connection, bolted or equivalent in SF6 °C ≤ 75
- Terminal °C ≤ 65

MECHANISM
Manufacture
Type
21 Number of interrupters in series per phase pcs 1
22 Number of tripping coils per phase pcs 2
23 Number of closing coils per phase pcs 1
24 Operating mechanism :
- Type spring-spring
- Number of stored energy operation 1 ( one per phase)
25 Protection level of control cubicle IP54
26 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230/400 V AC
- Heater Volt AC 230 VAC
27 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

11 dari 26

(......................................................) (..............................................)
#REF!

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR LINE BAY

NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

- motor % 85 to 110
28 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 50
2. Opening time (trip initiation to contact separation) without
ms ≤ 30
current
3. Time interval between opening of interrupters of first and last
ms ≤4
phase
4. Time interval between opening of interupters of one phase ms N/A
5. Making time without current ms ≤ 100
6. Time interval between closure of interrupters of the first and
ms ≤ 10
last pole
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
29 Number of auxiliary contacts (NO/NC) per pole pcs >8

OTHERS
30 Discrepancy device Yes
31 Antipumping device Yes
32 Method of controling voltage distribution between break unit N/A
33 Method of Closing control N/A
34 Value of closing resistor Ohm N/A
35 Insertion time of closing resistor ms N/A
36 SF6 Pressure Indicator per pole pcs 1
37 Counter to record number of operation per set pcs 3
Seismic acceleration constant consideration (according to
38 g 0,2 or 0,3
seismic map)
39 Leakage rate of SF6 gas per annum % ≤ 0.5
40 Contact resistance across main contacts per phase µ ohm < 100
Number of switch operations between two inspections for
41
changing the main-contacts :
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
42 Material of insulator Silicon Rubber or Porcelain
43 Minimum clearance in air :
- between phase mm 1800
- phase to earth mm 1500
- live conductor to ground level mm 3800

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

12 dari 26

(......................................................) (..............................................)
#REF!

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR LINE BAY

NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

- live insulator to ground level mm 2300

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

13 dari 26

(......................................................) (..............................................)
#REF!

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR SINGLE CAPACITOR

NO DESCRIPTION UNIT REQUIRED

Manufacturer to be mentioned
Type Designation to be mentioned
1 Standard IEC 62271-100 AND IEC 62271-1
2 Service condition refer to General Particulars of the site in Book B
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
6 Rated voltage (Ur) kV rms 170
7 Rated frequency (Fr) Hz 50
8 Rated normal current (Ir) A rms ≥ 1250
9 Rated short-time withstand current (I th) kA rms 31,5 or 40 or 50
10 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
11 Rated duration of short circuit s ≥ 1
12 Rated insulation level :
Power frequency withstand voltage, dry for 1 minute
Phase to earth, between the phases and across the open
kV rms 325
breaker gap
Impulse withstand voltage (at 1,2/50 microsecond)
Phase to earth, between the phases and across the open
kV peak 750
breaker gap
13 Minimum Creepage distance (according to degree of pollution)
a) Up to Heavy Pollution mm/kV 25
b) Very Heavy Pollution mm/kV 31
14 Operating Sequence And Operating Duty
- Nominal Sequence
(Not intended for rapid auto-reclosing) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
15 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms 31,5 or 40 or 50
- % dc component % dc > 20
16 Breaking current under out of phase condition kA rms ≥ 25 % x I th
17 Rated capacitive switching currents for Single capacitor A rms refer to IEC

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

14 dari 26

(......................................................) (..............................................)
#REF!

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR SINGLE CAPACITOR

NO DESCRIPTION UNIT REQUIRED

18 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz


- circuit closed to ground µV To be Mentioned
- circuit breaker open, grounded terminal µV To be Mentioned
19 Classes
- Electrical endurance E1
- Transient Recovery Voltage N/A
- Mechanical endurance M2
- Restrike performance C2
20 Temperature rise at :
- Contacts in SF6 °C ≤ 65
- Connection, bolted or equivalent in SF6 °C ≤ 75
- Terminal °C ≤ 65

MECHANISM
Manufacture
Type
21 Number of interrupters in series per phase pcs 1
22 Number of tripping coils per phase pcs 2
23 Number of closing coils per phase pcs 1
24 Operating mechanism :
- Type spring-spring
- Number of stored energy operation 3 (one per phase)
25 Protection level of control cubicle IP54
26 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230/400 V AC
- Heater Volt AC 230 VAC
27 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
- motor % 85 to 110
28 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 50

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

15 dari 26

(......................................................) (..............................................)
#REF!

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR SINGLE CAPACITOR

NO DESCRIPTION UNIT REQUIRED

2. Opening time (trip initiation to contact separation) without


ms ≤ 30
current
3. Time interval between opening of interrupters of first and last
ms ≤4
phase
4. Time interval between opening of interupters of one phase ms N/A
5. Making time without current ms ≤ 100
6. Time interval between closure of interrupters of the first and
ms ≤ 10
last pole
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
29 Number of auxiliary contacts (NO/NC) per pole pcs >8

OTHERS
30 Discrepancy device Yes
31 Antipumping device Yes
32 Method of controling voltage distribution between break unit N/A
33 Method of Closing control N/A
Value of closing resistor Ohm N/A
Insertion time of closing resistor ms N/A
34 SF6 Pressure Indicator per pole pcs 1
35 Counter to record number of operation per set pcs 3
Seismic acceleration constant consideration (according to
36 g 0,2 or 0,3
seismic map)
37 Leakage rate of SF6 gas per annum % ≤ 0.5
38 Contact resistance across main contacts per phase µ ohm < 100
Number of switch operations between two inspections for
39
changing the main-contacts :
- with rated continuous current times to be mentioned
- with rated breaking current times to be mentioned
40 Material of insulator Silicon Rubber or Porcelain
41 Minimum clearance in air :
- between phase mm 1800
- phase to earth mm 1500
- live conductor to ground level mm 3800
- live insulator to ground level mm 2300

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

16 dari 26

(......................................................) (..............................................)
0102-SS-E-TQU-102 : CIRCUIT BREAKER FOR LINE (1 POLE) TECHNICAL PARTICULAR GUARANTEE REV.00
NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
Manufacturer to be mentioned
Type Designation to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition Outdoor, Tropical Area
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3 (Three) Single Phase
6 Rated voltage (Ur) kV rms 170
7 Rated frequency (Fr) Hz 50
8 Rated normal current (Ir) A rms ≥ 3150
9 Rated short-time withstand current (Ik) 40
a) System with 2 unit IBT 250 MVA parallel kA rms 31.5
b) System with 2 unit IBT 500 MVA parallel kA rms 40
c) Special case kA rms 50
10 Rated peak withstand current (Ip) kA peak ≥ 2,5 x Ik
11 Rated duration of short circuit s ≥ 1
12 Rated Insulation Level :
- Rated short-duration power frequency withstand voltage (Ud) kV rms 325
- Rated lightning impulse withstand voltage (Up) kV peak 750
13 Minimum Creepage distance (according to degree of pollution)
mm/
Very Heavy Pollution 31
kV
14 Operating Sequence And Operating Duty
- Nominal Sequence

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

17 of 26

(......................................................) (..............................................)
0102-SS-E-TQU-102 : CIRCUIT BREAKER FOR LINE (1 POLE) TECHNICAL PARTICULAR GUARANTEE REV.00
NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
(rapid auto-reclosing/dead time) O - 0.3s - CO - 180s - CO
- Out of phase O - CO

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

18 of 26

(......................................................) (..............................................)
0102-SS-E-TQU-102 : CIRCUIT BREAKER FOR LINE (1 POLE) TECHNICAL PARTICULAR GUARANTEE REV.00
NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
15 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
kA
- Breaking current (symmetrical) 40
rms
- % dc component % ≤ 20
16 Rated out of phase breaking current kA rms ≥ 25 % x Ik
17 Rated capacitive switching currents for Line charging or Cable charging A rms refer to IEC 62271-100 table 9
- circuit closed to ground µV To be Mentioned
- circuit breaker open, grounded terminal µV To be Mentioned
18 Classes
- Electrical endurance E1
- Transient Recovery Voltage refer to IEC 62271-100 table 26
- Mechanical endurance M2
- Restrike performance C2
19 Temperature rise at :
- Contacts in SF6 °C ≤ 65
- Connection, bolted or equivalent in SF6 °C ≤ 75
- Terminal °C ≤ 65

MECHANISM
Manufacture
Type
20 Number of interrupters in series per phase pcs 1
21 Number of tripping coils per phase pcs 2

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

19 of 26

(......................................................) (..............................................)
0102-SS-E-TQU-102 : CIRCUIT BREAKER FOR LINE (1 POLE) TECHNICAL PARTICULAR GUARANTEE REV.00
NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
22 Number of closing coils per phase pcs 1
23 Operating mechanism :

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

20 of 26

(......................................................) (..............................................)
0102-SS-E-TQU-102 : CIRCUIT BREAKER FOR LINE (1 POLE) TECHNICAL PARTICULAR GUARANTEE REV.00
NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
- Type motor-spring
- Number of operation mechanism 3 ( one per phase)
24 Protection level of control cubicle (minimum) IP54
25 Supply voltage :
Volt
- Control voltage 110
DC
Volt
- Tripping and closing Coils 110
DC
Volt
- Motor voltage 230/400 V AC
AC
Volt
- Heater 230 VAC
AC
26 Tolerance range for auxiliary supply voltage
- tripping coil % 70 to 110
- closing coil % 85 to 110
- motor % 85 to 110
27 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 50
2. Opening time (trip initiation to contact separation) without current ms ≤ 40
3. Time interval between opening of interrupters of first and last phase ms ≤4
4. Time interval between opening of interupters of one phase ms N/A
5. Closing time without current ms ≤ 110
6. Time interval between closure of interrupters of the first and last pole ms ≤ 10
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
28 Number of auxiliary contacts (NO/NC) per pole pcs >8

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

21 of 26

(......................................................) (..............................................)
0102-SS-E-TQU-102 : CIRCUIT BREAKER FOR LINE (1 POLE) TECHNICAL PARTICULAR GUARANTEE REV.00
NO DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE

OTHERS
29 Discrepancy device Yes
30 Antipumping device Yes
31 Method of controling voltage distribution between break unit N/A
32 Method of Closing control N/A
33 Value of closing resistor Ohm N/A
34 Insertion time of closing resistor ms N/A
35 SF6 Pressure Indicator per pole pcs 1
36 Counter to record number of operation per set pcs 3
37 Seismic acceleration constant consideration (according to seismic map) g Refer to SNI 1726:2019
38 Leakage rate of SF6 gas per annum % ≤ 0.5
39 Contact resistance across main contacts per phase µ ohm < 80
Number of switch operations between two inspections for changing the main-
40
contacts :
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
41 Material of insulator Silicon Rubber or Porcelain
42 Minimum clearance in air :
- between phase mm to be mentioned (refer to IEC 61936-1)
- phase to earth mm to be mentioned (refer to IEC 61936-1)
- live conductor to ground level mm to be mentioned (refer to IEC 61936-1)
- live insulator to ground level mm to be mentioned (refer to IEC 61936-1)

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

22 of 26

(......................................................) (..............................................)
#REF!

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR SINGLE CAPACITOR

NO DESCRIPTION UNIT FINAL

Manufacturer Nama Pabrikan


tipe peralatan yang diproduksi sesuai dengan type test
Type Designation
yang diajukan
1 Standard IEC 62271-100 AND IEC 62271-1
2 Service condition Tropical design
refer to General Particular of site in Book B
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
6 Rated voltage (Ur) kV rms 170
7 Rated frequency (Fr) Hz 50
8 Rated normal current (Ir) A rms ≥ 1250
9 Rated short-time withstand current (I th) kA rms 31,5 or 40 or 50
10 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
11 Rated duration of short circuit s ≥ 1
12 RATED INSULATION LEVEL :
Power frequency withstand voltage, dry for 1 minute
Phase to earth, between the phases and across the open breaker gap kV rms 325
Impulse withstand voltage (at 1,2/50 microsecond)
Phase to earth, between the phases and across the open breaker gap kV peak 750
13 Minimum Creepage distance (according to degree of pollution) mm/kV 25 or 31
14 OPERATING SEQUENCE AND OPERATING DUTY
- Nominal Sequence
(Not intended for rapid auto-reclosing) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
15 Rated making and breaking current to Normal/Reclose
- Making current kA peak 2,5 x I th
- Breaking current (symmetrical) kA rms ≥ (25 or 31,5 or 40 or 50 or 63)
- % dc component % dc ≥ 20 To be Mentioned
16 Breaking current under out of phase condition kA rms ≥ 25 % x I th
17 Rated capacitive switching currents for Back to back capacitor A rms 400

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

23 dari 26

(......................................................) (..............................................)
#REF!

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR SINGLE CAPACITOR

NO DESCRIPTION UNIT FINAL

- Rated inrush making current (I bi) kA peak ≥ 20


- Frequency of inrush current (f bi) Hz 4250
18 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz
- circuit closed to ground µV ≤ 2500
- circuit breaker open, grounded terminal µV ≤ 2500
19 Classes
- Electrical endurance E1, E2
- Transient Recovery Voltage S2 N/A
- Mechanical endurance M2
- Restrike performance C2
20 Temperature rise at :
- Contacts in SF6 °C ≤ 65
- Connection, bolted or equivalent in SF6 °C ≤ 75
- Terminal °C ≤ 65

MECHANISM
Manufacture
Type
21 Number of interrupters in series per phase pcs 1
22 Number of tripping coils per phase pcs 2
23 Number of closing coils per phase pcs 1
24 Operating mechanism :
- Type spring-spring
- Number of stored energy operation 3 (one per phase)
25 Protection level of control cubicle IP54
26 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt DC/AC 110 V DC or 230 V AC
- Heater Volt AC 230 VAC
27 Tolerance range for auxiliary supply voltage

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

24 dari 26

(......................................................) (..............................................)
#REF!

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR SINGLE CAPACITOR

NO DESCRIPTION UNIT FINAL

- tripping coil % 85 to 110


- closing coil % 85 to 110
- motor % 85 to 110
28 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 50
2. Opening time (trip initiation to contact separation) without current ms ≤ 30
3. Time interval between opening of interrupters of first and last phase ms ≤4
4. Time interval between opening of interupters of one phase ms N/A
5. Making time without current ms ≤ 100
6. Time interval between closure of interrupters of the first and last pole ms ≤ 10
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
29 Number of auxiliary contacts (NO/NC) per pole pcs >8

OTHERS
30 Discrepancy device Yes
31 Antipumping device Yes
32 Method of controling voltage distribution between break unit N/A
33 Method of Closing control N/A
Value of closing resistor Ohm N/A
Insertion time of closing resistor ms N/A
34 SF6 Pressure Indicator per pole pcs 1
35 Counter to record number of operation per set pcs 6 3
36 Seismic acceleration constant consideration (according to seismic map) g 0,2 or 0,3
37 Leakage rate of SF6 gas per annum % ≤ 0.5
38 Contact resistance across main contacts per phase E1, E2 ≤ 60 to be mentioned
Number of switch operations between two inspections for changing the
39
main-contacts :
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
40 Material of insulator Polymer or Porcelain
BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

25 dari 26

(......................................................) (..............................................)
#REF!

TPG V.3. 2 : 150 KV CIRCUIT BREAKER FOR SINGLE CAPACITOR

NO DESCRIPTION UNIT FINAL

41 Minimum clearance in air :


- between phase mm to be mentioned (refer to IEC) 1800
- phase to earth mm to be mentioned (refer to IEC) 1500
- live conductor to ground level mm to be mentioned (refer to IEC) 3800
- live insulator to ground level mm to be mentioned (refer to IEC) 2300

BIDDER'S SIGNATURE MANUFACTURER'S SIGNATURE

26 dari 26

(......................................................) (..............................................)

You might also like