Chamfer VC-2C

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

B050G

MIRACLE Chamfering Cutter

VC-2C
VC-2C is a multi purpose chamfering cutter which can be
used not only for chamfering, but also chamfering of hole,
V slotting and center drilling.
y Widely used for milling from raw materials to hardened
steels and difficult-to-cut materials.
y VC-2C adopts MIRACLE coating (Al,Ti)N. It is possible to
cut high speed and high efficient machining.
y Due to end cutting edge, it is possible to cut V slotting
and center drilling.

Chamfering V slotting Center drilling

*With end cutting edge.


MIRACLE ENDMILLS

VC-2C
2 flute Chamfering Cutter
±0.02

øD1
15°

90°

øD4
øD2
Type 1
ap
L3
L1

UWC VC 5°

90°

øD1

øD4
øD2
Type 2
a It is possible to cut hardened steel & difficult-to-cut material. ap
L1
Unit : mm

Dia. Small mill Length of Neck Overall Shank No. of

Stock
Order Number Dia. Cut Length Length Dia. Flute Type
D2 D1 ap L3 L1 D4 N
VC2CD0200 2 0.3 0.85 6 50 6 2 a 1
D0400 4 0.3 1.85 12 50 6 2 a 1
D0600 6 0.3 2.85 ─ 50 6 2 a 2
D0800 8 0.4 3.8 ─ 60 8 2 a 2
D1000 10 0.5 4.75 ─ 70 10 2 a 2
D1200 12 0.5 5.75 ─ 75 12 2 a 2
a : Inventory maintained.

Carbon steel, Alloy steel Alloy steel, Tool steel Austenitic stainless steel Hardened steel
Work (─ 30HRC) Pre-hardened steel AISI 304, AISI 316 (45 ─ 55HRC)
material AISI 1049, SCM (30 ─ 45HRC) AISI H13
Cast iron FC250 AISI H13 NAK
Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate Revolution Feed rate
(mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min)
2 16,000 960 11,000 590 9,500 460 8,000 320
4 8,000 480 5,600 300 4,800 230 4,000 160
6 5,300 320 3,700 200 3,200 150 2,700 110
8 4,000 240 2,800 150 2,400 120 2,000 80
10 3,200 190 2,200 120 1,900 90 1,600 60
12 2,700 160 1,900 100 1,600 80 1,300 50
Camfering Chamfering milling of hole
Depth of
cut < 0.3D < 0.2D
(MAX. 2.5mm) D:Dia.

1) The above table shows cutting condition for chamfering milling.


For V slotting, please reduce the feed rate at 1/3 or below of the above value. For center drilling, please reduce the feed rate at 1/5 or
below of the above value.
2) If the rigidity of the machine or the material installation is very low, or chattering is generated, please reduce the revolution and the feed rate
of the above table proportionately.
3) In cutting austenitic stainless steels or hardened steels, cutting oil is recommended.

JQA-2522
JQA-EM0941

MITSUBISHI MATERIALS CORPORATION MITSUBISHI MATERIALS U.S.A. CORPORATION


MARKETING DEPT. Headquarters
KFC bldg., 8F, 1-6-1, Yokoami, Sumida-ku, Tokyo 130-0015, Japan 17401, Eastman Street, Irvine, California, 92614, USA
TEL 81-3-5819-8772 FAX 81-3-5819-8774 TEL 1-949-862-5100 FAX 1-949-862-5180

MMC HARTMETALL GmbH MMC METAL SINGAPORE PTE LTD.


Comeniusstr.2, 40670, Meerbusch GERMANY 10, Arumugam Road, #04-00 Lion Industrial Bldg.,409957, SINGAPORE
TEL 49-2159-9189-0 FAX 49-2159-50462 TEL 65-6743-9370 FAX 65-6749-1469

Home page
2003.9.E(1.5B)

You might also like