Detailed Programming Instructions (Standard Operations)

SmartPhone VI

Keypad Programming Remote Programming

Step 1: Begin Program Mode (Landline Phone Recommended)
a. Press Enter Step 1: Begin Program Mode
Step 2: Program Emergency Numbers a. Call into phone
a. Press 1, Enter, (phone number), Stop. b. After first simulated ring, press #, #
To program numbers 2-5, repeat Step 2 a. c. Key in security code (default is 1111)
Example: To program emergency number 2, press Step 2: Program Emergency Numbers
2, Enter, (phone number), Stop. a. Press 1, *, (phone number), *, #.
Note: If installed on a ring down line To program numbers 2-5, repeat Step 2 a.
(no dial tone) do not program phone number, press Example: To program emergency number 2, Press
the following: 1, 9, Enter, 2 (automatically sets the 2, *, (phone number), *, #. For a pause, press #, *.
timer for 3 minutes). Note: If installed on a ring down line (no dial tone) do
Step 3: Program Location Message not program a phone number, press the following: 1, 9,
a. To turn on message press 1, 3, Enter, 2 *, 2 (automatically sets the timer for 3 minutes).
b. Press 6, Record, wait for the “beep”, then speak Step 3: Program Location Message
message, Stop. To replay message, press 6, a. To turn on message, press 1, 3, *, 2
Play/Pause. b. Press 6, *, wait for the “beep”, then speak message,
c. Program frequency of message, press #. To replay message, press 6, #.
1, 3, Enter, __ c. Program frequency of message, press
0 = No message 1, 3, *, __
2 = Plays message (2) times (default) 0 = No message
3 = Plays message until receiving party presses * 2 = Plays message (2) times (default)
Note: Called party can replay message by pressing *,*. 3 = Plays message until receiving party presses *
Step 4: Exit Program Mode Note: Called party can replay message by pressing *,*.
a. Press Stop for 3 seconds Step 4: Exit Program Mode
a. Press *, #, 0 (you will hear beep beep) *, #

Optional Programming Features

Program Talk Timer Phone Line Check: (Default is 10 minutes)
(Default is 5 minutes, ring down is 3 minutes) Keypad: Press 3, 4, Enter, (4 digit number
Keypad: in HH:MM)
Press 8, Enter, (3 digit number in minutes) To turn off, press 23, Enter, 3, 23, Enter,
Remote: 7284, 11, Enter, 2
Press 8, *, (3 digit number in minutes) Remote: Press 3, 4, *, (4 digit number in HH:MM)
Example: 2 minutes = 002 To turn off, press 23, *, 3, 23, *, 7284, 11, *, 2
Note: After talk time expires, phone will prompt Example: 20 minutes = 0020, 10 hours = 1000
called party to extend call for 3 minutes. Example: 20 minutes = 0020, 10 hours = 1000

Consolidator Feature: (Allows up to (10) SmartPhones on a single

telephone line and toggle between them from an outside call)
Step 1: Begin Program Mode Step 4: Exit Program Mode
a. Press Enter a. Press Stop for 3 seconds
Step 2: Program ID Numbers for Phones 1-5 Step 5: Confirm Consolidator Operation
a. Press 7, Enter a. Dial phone number connected to
b. Press *, 1-5 for corresponding elevator 1-5 SmartPhones: All phones will answer
Step 3: Program ID Numbers for Phones 6-10 b. To select individual phone:
a. Press 7, Enter Press *1 (Phone #1) Press #1 (Phone #6)
b. Press #, 1-5 for corresponding elevator 6-10 Press *2 (Phone #2) Press #2 (Phone #7)
Press *3 (Phone #3) Press #3 (Phone #8)
Press *4 (Phone #4) Press #4 (Phone #9)
Press *5 (Phone #5) Press #5 (Phone #10)
Press *0 (All Phones)

2
N56W24720 N. Corporate Circle • Sussex, WI 53089 RP8200910
YEAR
WARRANTY 800-451-1460 • www.rathcommunications.com
Ver. 8
09/19
 Troubleshooting & Diagrams
SmartPhone VI

Wiring Diagrams: 24vac/dc Models

120vac to 24vac/dc Powered
Note: Note:
Direct 24vac/dc Powered If Elevator If Elevator

Re l a y A l a r m
Communications Communications
Failure is * Failure is
required, connect required, connect
Re l a y A l a r m

to our to our
Alarm Relay *
* Alarm Relay *

RJ11
Enter

Record
RJ11

LED Sw it c h
Play/Pause
Enter

Stop
Record
+-
To Phone Line: Bat MIC Speaker To Phone Line:
Requires a twisted Requires a twisted
LED

Play/Pause

shielded pair. shielded pair.

Sw it c h

Stop When used with When used with

SmartRescue, SmartRescue,
+-
Bat MIC Speaker requires two requires two
24v twisted shielded 24v twisted shielded
ac/dc
pairs. pairs.

RJ11
RP7300144-24/5VA

120vac
Black
To 24vac/dc Power Supply Hot Green
RJ11

Ground
White
Neutral

Annunciator Interface,
Auxiliary Relay & 24v LED Board 1. Connect your annunciator’s audio output to the TB1 connection
on this board.
24v LED 24vdc Power for LED

2. When utilizing this board to drive a 24v LED, you must apply
power to the wire leads at the TB2 connection. You may tap into
TB2
-+ Relay 1
a direct 24vdc supply that has battery backup. Connect the wire
-+ leads at the J5 connection to your LED.
To LED on SPVI

Relay 2 3. If you are not utilizing this board to drive a 24v LED, you need
to disconnect the LED harness from the SmartPhone board,
disconnect the LED harness from this board, connect it to the
-+

SmartPhone board, and then wire to your standard LED.

To Speaker
4. If you want to activate Relay 2 in unison with Alarm Relay on
SmartPhone board, follow these programming steps (default
activates upon call out):
To Audio output a. Press ENTER
of Annunciator
b. Press 3, 0, ENTER, 4
c. Press STOP for 3 seconds
To Speaker connection
To H1 on SP VI
on SP VI Circuit Board

N56W24720 N. Corporate Circle • Sussex, WI 53089

2 YEAR
WARRANTY 800-451-1460 • www.rathcommunications.com
RP8200910
Ver. 8
09/19
 Troubleshooting & Diagrams
SmartPhone VI

Initial Set-Up:
1. Diagnostic Test: Press Enter, 2, 6, Play/Pause phone will play back (5) Beeps (1st Beep=External Power Supply; 2nd
Beep=LED; 3rd Beep=Microphone; 4th Beep=Speaker; 5th Beep=Backup Battery). If any item fails during test you will hear
a Blat not a Beep. If you hear a Blat, contact RATH® Technical Support.
Note: If you receive a Blat for the LED, check the LED operation to be sure it is not working before contacting RATH® Technical Support.
2. Connect to standard RJ11 phone jack. If splicing connection, only hook up Red and Green Wires from the phone cable. If
connecting to a SmartRescue unit, you must connect all four wires (check for 24vdc or 48vdc supply at the splice).

Troubleshooting:
1. If the phone dials only one digit and hangs up, there is another Auto-Dialer on the line. You need to re-wire the system so
that the RATH® unit is either in parallel or ahead of it.
2. If the phone dials a couple of digits and gets a busy signal, the unit is installed on a switchboard line and needs to be
programmed to dial the appropriate access code to get an outside line (usually an 8 or 9).
3. If the phone does not respond, make sure the green LED (D1) on the circuit board is lit. If not, check to be sure the power is
properly connected.
4. If the phone is making phantom calls, it is installed on a Ring Down Line. You must turn off the “Telephone Line Check”
feature (see Optional Programming Instructions).

Wiring Diagrams: 12vac/dc Models:

Direct 12vac/dc Powered 120vac to 12vac/dc Powered

Re l a y A l a r m

Re l a y A l a r m

* *
RJ11

RJ11
Enter Enter
To Phone Line: To Phone Line:
Record
Requires a twisted Requires a twisted
Record
shielded pair. shielded pair.
When used with When used with
LED

Play/Pause
LE D S w i t ch

Play/Pause

SmartRescue, SmartRescue,
S wi t ch

Stop requires two Stop requires two

+- twisted shielded +- twisted shielded
Bat
Bat MIC Speaker pairs. MIC Speaker pairs.
12vac/dc

12v
RJ11

RJ11

To 12vac/dc White/Neutral
Power Supply Transformer To 120vac
Note: If Elevator Communications Failure is Black/Hot
required, connect to our Alarm Relay. *

N56W24720 N. Corporate Circle • Sussex, WI 53089 RP8200910

2 YEAR
WARRANTY 800-451-1460 • www.rathcommunications.com
Ver. 8
09/19