SDS 25780 Steelmaster 1200WF Eng CA

Download as pdf or txt
Download as pdf or txt
You are on page 1of 10

Conforms to WHMIS 2015, Canadian Hazardous Products Regulation (HPR)

SAFETY DATA SHEET

SteelMaster 1200WF
Section 1. Identification
Product identifier : SteelMaster 1200WF
Product code : 25780
Product description : Paint.
Other means of : Not available.
identification
Product type : Liquid.

Supplier's details : Jotun Paints, Inc.


9203 Highway 23
Belle Chasse, LA 70037
Telephone: (800) 229-3538 or
+1 504-394-3538
[email protected]

Emergency telephone : 1-800-424-9300


number (with hours of (Staffed 24/7)
operation)
25780 1 25780 ^(ValidationDate) 1

Approved

Section 2. Hazard identification


Classification of the : TOXIC TO REPRODUCTION - Category 2
substance or mixture

GHS label elements


Hazard pictograms :

Signal word : Warning.


Hazard statements : Suspected of damaging fertility or the unborn child.
Precautionary statements
Prevention : Obtain special instructions before use. Wear protective gloves, protective clothing
and eye or face protection.
Response : IF exposed or concerned: Get medical advice or attention.
Storage : Not applicable.
Disposal : Dispose of contents and container in accordance with all local, regional, national
and international regulations.

Section 3. Composition/information on ingredients


Substance/mixture : Mixture
Other means of : Not available.
identification

CAS number/other identifiers


CAS number : Not applicable.

Date of issue : 06.05.2021 1/10


SteelMaster 1200WF

Section 3. Composition/information on ingredients


Product code : 25780
Ingredient name % CAS number
melamine 5 - 10 108-78-1
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require
reporting in this section.
Occupational exposure limits, if available, are listed in Section 8.

Section 4. First-aid measures


Description of necessary first aid measures
Eye contact : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention if irritation occurs.
Inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing.
If not breathing, if breathing is irregular or if respiratory arrest occurs, provide
artificial respiration or oxygen by trained personnel. It may be dangerous to the
person providing aid to give mouth-to-mouth resuscitation. Get medical attention. If
unconscious, place in recovery position and get medical attention immediately.
Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or
waistband. In case of inhalation of decomposition products in a fire, symptoms may
be delayed. The exposed person may need to be kept under medical surveillance
for 48 hours.
Skin contact : Flush contaminated skin with plenty of water. Remove contaminated clothing and
shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash
clothing before reuse. Clean shoes thoroughly before reuse.
Ingestion : Wash out mouth with water. Remove dentures if any. Remove victim to fresh air
and keep at rest in a position comfortable for breathing. If material has been
swallowed and the exposed person is conscious, give small quantities of water to
drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not
induce vomiting unless directed to do so by medical personnel. If vomiting occurs,
the head should be kept low so that vomit does not enter the lungs. Get medical
attention. Never give anything by mouth to an unconscious person. If unconscious,
place in recovery position and get medical attention immediately. Maintain an open
airway. Loosen tight clothing such as a collar, tie, belt or waistband.

Most important symptoms/effects, acute and delayed


Potential acute health effects
Eye contact : No known significant effects or critical hazards.
Inhalation : No known significant effects or critical hazards.
Skin contact : No known significant effects or critical hazards.
Ingestion : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact : No specific data.
Inhalation : Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Skin contact : Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Ingestion : Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations

Date of issue : 06.05.2021 2/10


SteelMaster 1200WF

Section 4. First-aid measures

Indication of immediate medical attention and special treatment needed, if necessary


Notes to physician : In case of inhalation of decomposition products in a fire, symptoms may be delayed.
The exposed person may need to be kept under medical surveillance for 48 hours.
Specific treatments : No specific treatment.
Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. It
may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.

See toxicological information (Section 11)

Section 5. Fire-fighting measures


Extinguishing media
Suitable extinguishing : Use an extinguishing agent suitable for the surrounding fire.
media
Unsuitable extinguishing : None known.
media

Specific hazards arising : In a fire or if heated, a pressure increase will occur and the container may burst.
from the chemical
Hazardous thermal : Decomposition products may include the following materials:
decomposition products carbon dioxide
carbon monoxide
nitrogen oxides
metal oxide/oxides

Special protective actions : Promptly isolate the scene by removing all persons from the vicinity of the incident if
for fire-fighters there is a fire. No action shall be taken involving any personal risk or without
suitable training.
Special protective : Fire-fighters should wear appropriate protective equipment and self-contained
equipment for fire-fighters breathing apparatus (SCBA) with a full face-piece operated in positive pressure
mode.

Section 6. Accidental release measures


Personal precautions, protective equipment and emergency procedures
For non-emergency : No action shall be taken involving any personal risk or without suitable training.
personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Avoid breathing vapor or
mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Put on appropriate personal protective equipment.
For emergency responders : If specialized clothing is required to deal with the spillage, take note of any
information in Section 8 on suitable and unsuitable materials. See also the
information in "For non-emergency personnel".

Environmental precautions : Avoid dispersal of spilled material and runoff and contact with soil, waterways,
drains and sewers. Inform the relevant authorities if the product has caused
environmental pollution (sewers, waterways, soil or air).

Methods and materials for containment and cleaning up


Small spill : Stop leak if without risk. Move containers from spill area. Dilute with water and mop
up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry
material and place in an appropriate waste disposal container. Dispose of via a
licensed waste disposal contractor.

Date of issue : 06.05.2021 3/10


SteelMaster 1200WF

Section 6. Accidental release measures


Large spill : Stop leak if without risk. Move containers from spill area. Approach release from
upwind. Prevent entry into sewers, water courses, basements or confined areas.
Wash spillages into an effluent treatment plant or proceed as follows. Contain and
collect spillage with non-combustible, absorbent material e.g. sand, earth,
vermiculite or diatomaceous earth and place in container for disposal according to
local regulations (see Section 13). Dispose of via a licensed waste disposal
contractor. Contaminated absorbent material may pose the same hazard as the
spilled product. Note: see Section 1 for emergency contact information and Section
13 for waste disposal.

Section 7. Handling and storage


Precautions for safe handling
Protective measures : Put on appropriate personal protective equipment (see Section 8). Avoid exposure -
obtain special instructions before use. Avoid exposure during pregnancy. Do not
handle until all safety precautions have been read and understood. Do not get in
eyes or on skin or clothing. Do not ingest. Avoid breathing vapor or mist. If during
normal use the material presents a respiratory hazard, use only with adequate
ventilation or wear appropriate respirator. Keep in the original container or an
approved alternative made from a compatible material, kept tightly closed when not
in use. Empty containers retain product residue and can be hazardous. Do not
reuse container.
Advice on general : Eating, drinking and smoking should be prohibited in areas where this material is
occupational hygiene handled, stored and processed. Workers should wash hands and face before
eating, drinking and smoking. Remove contaminated clothing and protective
equipment before entering eating areas. See also Section 8 for additional
information on hygiene measures.

Conditions for safe storage, : Store in accordance with local regulations. Store in original container protected
including any from direct sunlight in a dry, cool and well-ventilated area, away from incompatible
incompatibilities materials (see Section 10) and food and drink. Store locked up. Keep container
tightly closed and sealed until ready for use. Containers that have been opened
must be carefully resealed and kept upright to prevent leakage. Do not store in
unlabeled containers. Use appropriate containment to avoid environmental
contamination. See Section 10 for incompatible materials before handling or use.

Section 8. Exposure controls/personal protection


Control parameters
Occupational exposure limits
Ingredient name Exposure limits
melamine AIHA WEEL (United States, 7/2018).
TWA: 3 mg/m³ 8 hours.

Appropriate engineering : If user operations generate dust, fumes, gas, vapor or mist, use process enclosures,
controls local exhaust ventilation or other engineering controls to keep worker exposure to
airborne contaminants below any recommended or statutory limits.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process
equipment will be necessary to reduce emissions to acceptable levels.

Individual protection measures


Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and
safety showers are close to the workstation location.

Date of issue : 06.05.2021 4/10


SteelMaster 1200WF

Section 8. Exposure controls/personal protection


Eye/face protection : Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn,
unless the assessment indicates a higher degree of protection: safety glasses with
side-shields.
Skin protection
Hand protection : Chemical-resistant, impervious gloves complying with an approved standard should
be worn at all times when handling chemical products if a risk assessment indicates
this is necessary. Considering the parameters specified by the glove manufacturer,
check during use that the gloves are still retaining their protective properties. It
should be noted that the time to breakthrough for any glove material may be
different for different glove manufacturers. In the case of mixtures, consisting of
several substances, the protection time of the gloves cannot be accurately
estimated.
There is no one glove material or combination of materials that will give unlimited
resistance to any individual or combination of chemicals.
The breakthrough time must be greater than the end use time of the product.
The instructions and information provided by the glove manufacturer on use,
storage, maintenance and replacement must be followed.
Gloves should be replaced regularly and if there is any sign of damage to the glove
material.
Always ensure that gloves are free from defects and that they are stored and used
correctly.
The performance or effectiveness of the glove may be reduced by physical/chemical
damage and poor maintenance.
Barrier creams may help to protect the exposed areas of the skin but should not be
applied once exposure has occurred.
Wear suitable gloves tested to EN374.
Recommended, gloves(breakthrough time) > 8 hours: nitrile rubber, neoprene, PVC
May be used, gloves(breakthrough time) 4 - 8 hours: 4H

Body protection : Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product.
Other skin protection : Appropriate footwear and any additional skin protection measures should be
selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Respiratory protection : Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.

Section 9. Physical and chemical properties


Appearance
Physical state : Liquid.
Color : White.
Odor : Characteristic.
Odor threshold : Not available.
pH : 8 to 9
Melting point : Not available.
Boiling point : Lowest known value: 100°C (212°F) (water). Weighted average: 103.45°C (218.2°F)
Flash point : Not available.
Evaporation rate : Not available.
Flammability (solid, gas) : Not available.
Lower and upper explosive : Not available.
(flammable) limits
Vapor pressure : Not available.

Date of issue : 06.05.2021 5/10


SteelMaster 1200WF

Section 9. Physical and chemical properties


Vapor density : Not available.
Relative density : 1.397 to 1.409 g/cm³ 11.66 to 11.76 pounds/gallon
Solubility : Easily soluble in the following materials: cold water and hot water.
Partition coefficient: n- : Not available.
octanol/water
Auto-ignition temperature : Not available.
Decomposition temperature : Not available.
Viscosity : Kinematic (40°C (104°F)): >0.205 cm2/s (>20.5 mm2/s)

Section 10. Stability and reactivity


Reactivity : No specific test data related to reactivity available for this product or its ingredients.

Chemical stability : The product is stable.

Possibility of hazardous : Under normal conditions of storage and use, hazardous reactions will not occur.
reactions

Conditions to avoid : No specific data.

Incompatible materials : No specific data.

Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products
products should not be produced.

Section 11. Toxicological information


Information on toxicological effects
Acute toxicity
Product/ingredient name Result Species Dose Exposure
melamine LD50 Oral Rat 3161 mg/kg -
Irritation/Corrosion
Product/ingredient name Result Species Score Exposure Observation
melamine Eyes - Mild irritant Rabbit - 24 hours 500 -
milligrams
Sensitization
Not available.

Mutagenicity
Not available.
Carcinogenicity
Not available.
Reproductive toxicity
Not available.
Teratogenicity
Not available.
Specific target organ toxicity (single exposure)
Not available.
Specific target organ toxicity (repeated exposure)
Not available.

Date of issue : 06.05.2021 6/10


SteelMaster 1200WF

Section 11. Toxicological information


Aspiration hazard
Not available.

Information on the likely : Not available.


routes of exposure
Potential acute health effects
Eye contact : No known significant effects or critical hazards.
Inhalation : No known significant effects or critical hazards.
Skin contact : No known significant effects or critical hazards.
Ingestion : No known significant effects or critical hazards.

Symptoms related to the physical, chemical and toxicological characteristics


Eye contact : No specific data.
Inhalation : Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Skin contact : Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Ingestion : Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations

Delayed and immediate effects and also chronic effects from short and long term exposure
Short term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.
Long term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.
Potential chronic health effects
Not available.
General : No known significant effects or critical hazards.
Carcinogenicity : No known significant effects or critical hazards.
Mutagenicity : No known significant effects or critical hazards.
Teratogenicity : No known significant effects or critical hazards.
Developmental effects : No known significant effects or critical hazards.
Fertility effects : Suspected of damaging fertility.

Numerical measures of toxicity


Acute toxicity estimates
Not available.

Date of issue : 06.05.2021 7/10


SteelMaster 1200WF

Section 12. Ecological information


Toxicity
Not available.

Persistence and degradability


Not available.

Bioaccumulative potential
Product/ingredient name LogPow BCF Potential
melamine -1.22 <3.8 low

Mobility in soil
Soil/water partition : Not available.
coefficient (KOC)

Other adverse effects : No known significant effects or critical hazards.

Section 13. Disposal considerations


Disposal methods : The generation of waste should be avoided or minimized wherever possible.
Disposal of this product, solutions and any by-products should at all times comply
with the requirements of environmental protection and waste disposal legislation
and any regional local authority requirements. Dispose of surplus and non-
recyclable products via a licensed waste disposal contractor. Waste should not be
disposed of untreated to the sewer unless fully compliant with the requirements of
all authorities with jurisdiction. Waste packaging should be recycled. Incineration or
landfill should only be considered when recycling is not feasible. This material and
its container must be disposed of in a safe way. Care should be taken when
handling emptied containers that have not been cleaned or rinsed out. Empty
containers or liners may retain some product residues. Avoid dispersal of spilled
material and runoff and contact with soil, waterways, drains and sewers.
Do not allow to enter drains or watercourses. Material and/or container must be disposed of as hazardous waste.

Section 14. Transport information


TDG DOT ADR/RID IMDG IATA
Classification Classification
UN number Not regulated. Not regulated. Not regulated. Not regulated. Not regulated.

UN proper - - - - -
shipping name
Transport - - - - -
hazard class(es)

Packing group - - - - -
Environmental No. No. No. No. No.
hazards

Additional information
TDG Classification : -
DOT Classification : -
ADR/RID : -

Date of issue : 06.05.2021 8/10


SteelMaster 1200WF

Section 14. Transport information


IMDG : Marine pollutant: No.
IATA : -

Special precautions for user : Transport within user’s premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in
the event of an accident or spillage.

Transport in bulk according : Not available.


to IMO instruments

Section 15. Regulatory information


Canadian lists
Canadian NPRI : The following components are listed: phosphorus (total)
CEPA Toxic substances : None of the components are listed.
Canada inventory : Not determined.
International regulations
Chemical Weapon Convention List Schedules I, II & III Chemicals
Not listed.

Montreal Protocol
Not listed.
Stockholm Convention on Persistent Organic Pollutants
Not listed.
UNECE Aarhus Protocol on POPs and Heavy Metals
Not listed.
Inventory list
Australia : Not determined.
China : Not determined.
Europe : At least one component is not listed.
Japan : Japan inventory (ENCS): Not determined.
Japan inventory (ISHL): Not determined.
Malaysia : Not determined
New Zealand : Not determined.
Philippines : Not determined.
Republic of Korea : Not determined.
Taiwan : Not determined.
Turkey : Not determined.
United States : Not determined.

Section 16. Other information


History
Date of printing : 06.05.2021
Date of issue/Date of : 06.05.2021
revision
Date of previous issue : 28.04.2021
Version : 1.05

Date of issue : 06.05.2021 9/10


SteelMaster 1200WF

Section 16. Other information


Key to abbreviations : ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships,
1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution)
UN = United Nations
HPR = Hazardous Products Regulations
Procedure used to derive the classification
Classification Justification
TOXIC TO REPRODUCTION - Category 2 Calculation method

References : Not available.


Indicates information that has changed from previously issued version.
Notice to reader
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are
often used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the
product itself. Minor product variations may be implemented in order to comply with local requirements.
Jotun reserves the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their
needs and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United
Kingdom) version will prevail.

Date of issue : 06.05.2021 10/10

You might also like