ME6118 Microne
ME6118 Microne
ME6118 Microne
SOT223
Pin Assignment
ME6118AXX
Pin Number
Pin Name Functions
SOT223
1 GND Ground
2 VOUT Output
3 VIN Power Input
Electrical Characteristics
ME6118A12
(VIN= VOUT +1.3V,CIN=CL=10uF,Ta=25OC, unless otherwise noted)
Parameter Symbol Conditions Min. Typ. Max. Units
VOUT(E) IOUT=10mA, VOUT (T)
Output Voltage X 0.98 X 1.02 V
(Note 2) VIN= VOUT +1.3V (Note 1)
Maximum Output
IOUTMAX VIN= VOUT +1.3V 800 mA
Current
VIN= VOUT +1.3V ,
Load Regulation ∆VOUT 3 10 mV
1mA≤IOUT ≤800mA
VDIF1 IOUT =100mA 195 mV
Dropout Voltage VDIF2 IOUT =400mA 665 mV
(Note 3) VDIF3 IOUT =800mA 1250 mV
Quiescent Current Iss VIN= VOUT +1.3V 53 uA
IOUT =0mA
Line Regulation ∆VOUT 2 10 mV
VOUT+1.3V ≤VIN≤18V
Thermal Shutdown IOUT=10mA,
Tsd 155 ℃
Protection VIN= VOUT +1.3V
Over Current
Ilimit VIN=3V 1.1 A
Protection
Note :
1. VOUT (T) :Specified Output Voltage
2.VOUT (E) :Effective Output Voltage ( ie. The output voltage when “VOUT (T)+1.2V”is provided at the Vin pin while
maintaining a certain Iout value.)
3.VDIF:VIN1 –VOUT (E)’
VIN1 :The input voltage when VOUT(E)’ appears as input voltage is gradually decreased.
VOUT (E)’=A voltage equal to 98% of the output voltage whenever an amply stabilized Iout and {VOUT
(T)+1.2V} is input.
1.23 1.85
1.22 1.83
Output Voltage(V)
Output Voltage(V)
1.21 1.81
1.20 1.79
1.19 1.77
1.18 1.75
1.17 1.73
1.16 1.71
0 100 200 300 400 500 600 700 800 0 100 200 300 400 500 600 700 800
Output Current(mA) Output Current(mA)
2.53 3.33
Output Voltage(V)
3.32
Output Voltage(V)
2.52
2.51 3.31
2.50 3.30
2.49 3.29
2.48 3.28
2.47 3.27
2.46 3.26
0 100 200 300 400 500 600 700 800 0 100 200 300 400 500 600 700 800
Output Current(mA) Output Current(mA)
1.24 1.85
1.83
Output Voltage(V)
Output Voltage(V)
1.22
1.20 1.81
1.18 1.79
1.16 1.77
1.14 1.75
1.12 1.73
0 30 60 90 120 150 0 30 60 90 120 150
Temperature(℃) Temperature(℃)
2.54 3.34
3.32
Output Voltage(V)
2.52
2.50 3.30
2.48 3.28
Output
2.46 3.26
2.44 3.24
2.42 3.22
0 30 60 90 120 150 0 30 60 90 120 150
T e m p e r a t℃)
ure( Temperature(℃)
1000
1400
Dropout Voltage(mV)
Dropout Voltage(mV)
1200 800
1000
600
800
600 400
400
200
200
0 0
0 100 200 300 400 500 600 700 800 0 100 200 300 400 500 600 700 800
Output Current(mA) Output Current(mA)
ME6118A25 ME6118A33
1000 700
Dropout Voltage(mV)
800 600
500
600 400
400 300
200
200
100
0 0
0 100 200 300 400 500 600 700 800 0 100 200 300 400 500 600 700 800
Output Current(mA) Output Current(mA)
Output Voltage(V)
1.20 1.83
1.19
1.80
1.18
1.77
1.17
1.16 1.74
1.15
1.71
2 4 6 8 10 12 14 16 18 2 4 6 8 10 12 14 16 18
Input Voltage(V) Input Voltage(V)
ME6118A25 ME6118A33
2.52
Output Voltage(V)
3.31
2.51
3.30
2.50
3.29
2.49
3.28
2.48
2.47 3.27
2.46 3.26
2 4 6 8 10 12 14 16 18 2 4 6 8 10 12 14 16 18
Input Voltage(V) Input Voltage(V)
Quiescent Current VS. Input Voltage Quiescent Current VS. Input Voltage
60 63
Quiescent Current(uA)
Quiescent Current(uA)
55 58
50 53
45 48
40 43
35 38
30 33
25 28
2 4 6 8 10 12 14 16 18 2 4 6 8 10 12 14 16 18
Input Voltage(V) Input Voltage(V)
Quiescent Current VS. Input Voltage Quiescent Current VS. Input Voltage
65 70
Quiescent Current(uA)
Quiescent Current(uA)
60 65
55 60
50 55
45 50
40 45
35 40
30 35
2 4 6 8 10 12 14 16 18 2 4 6 8 10 12 14 16 18
Input Voltage(V) Input Voltage(V)
Applications Information
1. Input Bypass Capacitor
An input capacitor is recommended. A 10uF tantalum on the input is a suitable input bypassing for almost all
applications.
2. Output Capacitor
The output capacitor is critical in maintaining regulator stability, and must meet the required conditions for both
minimum amount of capacitance and ESR (Equivalent Series Resistance).The minimum output capacitance
required by the ME6118 is 10µF,if a tantalum capacitor is used. Any increase of the output capacitance will
merely improve the loop stability and transient response. The ESR of the output capacitor should be less than
0.5Ω .
3. Load Regulation
The ME6118 regulates the voltage that appears between its output and ground pins, or between its output and
adjust pins. In some cases, line resistances can introduce errors to the voltage across the load. To obtain the
best load regulation, a few precautions are needed. Figure1, shows a typical application using a fixed output
regulator. The Rt1 and Rt2 are the line resistances. It is obvious that the VLOAD is less than the VOUT by the sum of
the voltage drops along the line resistances. In this case, the load regulation seen at the RLOAD would be
degraded from the datasheet specification. To improve this , the load should be tied directly to the output terminal
on the positive side and directly tied to the ground terminal on the negative side.
● SOT223