Scribd
Upload
56 views6 pages

Cat MID

This document provides definitions for various fault codes and module identifiers related to electronic engine controls. It defines Fault Mode Identifiers (FMI) codes 08 through 19, which relate to issues with sensors, communication errors, abnormal signal rates of change, and received network data errors. It also lists Module Identifiers (MID) codes from 9 to 255 that describe different electronic control modules. Finally, it outlines some event codes from 1 to 12 that indicate engine-related fault conditions like filter restrictions, overspeed events, and high crankcase pressure.

Uploaded by

purwa cute
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
56 views6 pages

Cat MID

This document provides definitions for various fault codes and module identifiers related to electronic engine controls. It defines Fault Mode Identifiers (FMI) codes 08 through 19, which relate to issues with sensors, communication errors, abnormal signal rates of change, and received network data errors. It also lists Module Identifiers (MID) codes from 9 to 255 that describe different electronic control modules. Finally, it outlines some event codes from 1 to 12 that indicate engine-related fault conditions like filter restrictions, overspeed events, and high crankcase pressure.

Uploaded by

purwa cute
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

777D Off-Highway Truck AGC00001-UP (MACHINE) POWERED BY 3508B Engin...

Page 92 of 130

FMI 08 occurs when a frequency of the signal or the pulse width of the signal is not within the range
that is expected. FMI 08 can also relate to a faulty sensor.

Note: The period is the time in seconds for one cycle at a specific frequency.

FMI 09 - "Abnormal update"

FMI 09 pertains to the communication between the electronic controls on the data link. FMI 09 occurs
when an electronic control is not able to receive information from another electronic control and when
the electronic control expects to receive the information.

FMI 10 - "Abnormal rate of change"

FMI 10 relates to a signal that changes too fast. The rate of change is outside of the expected limit.

FMI 11 - "Failure mode not identifiable"

FMI 11 occurs when the electronic control identifies more than one FMI as being responsible for a
single problem.

FMI 12 - "Bad device or component"

FMI 12 describes the following condition: An electronic control sends a signal to another electronic
module over a data link. The electronic control expects a response but the electronic control receives no
response or an incorrect response.

FMI 12 also describes the following condition: An electronic module is expected to send data
periodically but the electronic control does not send the data.

FMI 13 - "Out of calibration"

Some of the possible causes of an FMI 13 fault are listed below.

l Calibration is required.

l The data is out of the range.

FMI 14 - "Special Instruction"

FMI 19 - "Received Network Data in Error"

This type of failure is associated with network data that is received. The component that is used to
measure the real world signal is wired directly to the module that is sourcing the data to the network.
The component is not wired to the module that is receiving the data via the network.

Module Identifiers (MID)


Table 3

https://tci-ap1-snk.thiess.idn/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2/09/2007
777D Off-Highway Truck AGC00001-UP (MACHINE) POWERED BY 3508B Engin... Page 93 of 130

MID No. Description


9 "Handheld Service Tool"
10 "Digital Diagnostic Tool"

11 "Communication Adapter"
12 "Electronic Control Analyzer Programmer"
13 "CAT Electronic Technician"
14 "Electronic Ignition System"
15 "Spark Ignited Engine Timing Control"
17 "34XX SI Engine Control"
18 "35XX SI Engine Control"
19 "36XX SI Engine Control"

20 "Torsional Control"
21 "G3600 I/O Module"
22 "G3600 Pressure Module"
23 "Detonation Module"
25 "Ether Aid Control"
26 "CMS (Computerized Monitoring System)"
27 "Transmission/Chassis Control"

28 "Traction Aid Control"


29 "Computerized Profiler Control"
30 "Caterpillar Monitoring System"
31 "Electronic Scraper Transmission Control"
33 "Engine Control #2"
34 "Engine Control #3"
35 "Engine Control #4"
36 "Engine Control #1"

37 "Engine Control #5"


38 "Engine Control #6"

https://tci-ap1-snk.thiess.idn/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2/09/2007
777D Off-Highway Truck AGC00001-UP (MACHINE) POWERED BY 3508B Engin... Page 94 of 130

39 "Machine Control Module"


40 "Engine Control #7"
41 "Engine Control #8"

42 "Engine Control #9"


43 "Engine Control #10"
47 "Backup Engine Control"
49 "VIMS (Vital Information Management System) Main Module"
50 "VIMS Analysis Module"
51 "VIDS (Vital Information Display System) Main Module"
52 "VIDS/VIMS Graphics Display Module"
53 "Graphical Display Module"

54 "Caterpillar Monitoring System #2"


57 "Interface Module #1"
58 "Interface Module #2"
59 "Interface Module #3"
60 "Interface Module #4"
61 "Data Acquistion Module"
65 "Interface Module #5"

66 "Interface Module #6"


67 "Interface Module #7"
68 "Interface Module #8"
73 "Auto Ride/2-speed Fan Control"
74 "Payload Control System"
75 "All-Wheel Drive Control"
76 "DeNOx Control"
77 "DeNOx Display"

78 "Hitch Control"
79 "Hydrostatic Transmission Control"

https://tci-ap1-snk.thiess.idn/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2/09/2007
777D Off-Highway Truck AGC00001-UP (MACHINE) POWERED BY 3508B Engin... Page 95 of 130

81 "Transmission Control"
82 "Electronic Implement Control"
83 "Automatic Retarder Control"

84 "Paver Burner Control"


85 "Engine Fan Control"
86 "Global Positioning System Interface Module"
87 "Chassis Control Module"
88 "Generator Set Control #1"
89 "Generator Set Control #2"
90 "Generator Set Control #3"
91 "Generator Set Control #4"

92 "Generator Set Control #5"


93 "Generator Set Control #6"
94 "Generator Set Control #7"
95 "Generator Set Control #8"
97 "Customer Communication Module"
98 "Customer Communication Module Special"
99 "Programmable Relay Control Module"

100 "Engine Vision Display"


101 "Engine Vision Interface Module"
102 "Customer Communication Module #2"
103 "Remote Display #2"
105 "Hydraulic Pump Control"
106 "Electro-hydraulic Control Module"
107 "Integrated Temperature Sensing Module #2"
108 "Versatile Control Module"

109 "Integrated Combustion Sensing Module #1"


110 "Integrated Combustion Sensing Module #2"

https://tci-ap1-snk.thiess.idn/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2/09/2007
777D Off-Highway Truck AGC00001-UP (MACHINE) POWERED BY 3508B Engin... Page 96 of 130

111 "Integrated Temperature Sensing Module"


113 "TTT Transmission Control"
114 "Grade Slope Control"

115 "Slope Sensor Module"


116 "Integrated Brake Control"
117 "Transmission Shift Lever Module"
118 "Paver Burner Control #3"
119 "Paver Burner Control #2"
121 "CAES (Computer Aided Earth moving System)"
122 "Product Link Module"
123 "Data Link Translation Module"

124 "Theft Deterrent Module"


125 "Caterpillar Monitoring System #3"
126 "System Master Control Module"
127 "Data Link Translation Module #2"
129 "Training Aid #1"
130 "Training Aid #2"
131 "Test Cell Computer"

132 "Wireless Transceiver"


133 "Security System Key Reader"
137 "Grade Slope Display #1"
138 "Grade Slope Display #2"
139 "Grade Slope Display #3"
140 "Grade Slope Display #4"
141 "Grade Slope Display #5"
142 "Grade Slope Display #6"

145 "Electronic Implement Control #2"


146 "Transmission Control #2"

https://tci-ap1-snk.thiess.idn/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2/09/2007
777D Off-Highway Truck AGC00001-UP (MACHINE) POWERED BY 3508B Engin... Page 97 of 130

147 "Electronic Implement Control #3"


153 "Alarm Control #1"
154 "Alarm Control #2"

155 "Alarm Control #3"


156 "Operator Station #1 Module"
157 "Operator Station #2 Module"
161 "Communication Gateway #1"
162 "Communication Gateway #2"
163 "Communication Gateway #3"
254 "Flashing ECM"
255 "Blank ECM (Electronic Control Module)"

Event Codes
Table 4

Event Code
Description

1 "Engine Oil Filter Restriction Derate"


2 "Engine Oil Filter Restriction Shutdown"
3 "Engine Overspeed Derate"
4 "Engine Overspeed Shutdown"
5 "Fuel Filter Restriction Derate"
6 "Fuel Filter Restriction Shutdown"

7 "High Aftercooler Temperature Derate"


8 "High Aftercooler Temperature Shutdown"
9 "High Altitude Derate"
10 "High Altitude Shutdown"
11 "High Altitude Warning"
12 "High Crankcase Pressure Derate"

https://tci-ap1-snk.thiess.idn/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2/09/2007

You might also like