Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.

1 of 17

PRODUCT SPECIFICATIONS
n PHYSICAL DATA
n EXTERNAL DIMENSIONS
n BLOCK DIAGRAM
n ABSOLUTE MAXIMUM RATINGS
n ELECTRICAL CHARACTERISTICS
n TIMING CHART OF INPUT SIGNALS
n DISPLAY DATA PATTERN
n TIMING OF POWER SUPPLY
n EXAMPLE OF POWER CONNECTION
n ELECTRO-OPTICAL CHARACTERISTICS
n INTERFACE PIN CONNECTIONS
n CIRCUIT DIAGRAM
n MODULE PACKAGE
n RELIABILITY
n QUALITY GUARANTEE
n INSPECTION CRITERIA
n PRECAUTIONS FOR USING LCD MODULES
n USING LCD MODULES
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.2 of 17

n PHYSICAL DATA

Item Contents Unit

LCD type STN / FSTN ---
LCD duty 1/320 ---
LCD bias 1/19 ---
Viewing direction 6 / 12 o’clock
Module size (W H T) 70.5 89.0 8.0MAX mm
Viewing area (W H) 61.10 80.55 mm
Number of dots 240 320 dots
Dot size (W H) 0.225 0.225 mm
Dot pitch (W H) 0.24 0.24 mm

n EXTERNAL DIMENSIONS
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.3 of 17

n BLOCK DIAGRAM

n ABSOLUTE MAXIMUM RATINGS ( Ta = 25°C )

Parameter Symbol Min Max Unit
Supply voltage for logic VDD -0.3 7.0 V
Supply voltage for LCD VDD - VEE -0.3 +30.0 V
Input voltage VI -0.3 VDD + 0.3 V
Normal operating temperature TOP 0 50 °C
Normal storage temperature TST -10 60 °C
Wide operating / storage TOP / TST -30 80 C
temperature (except FSTN)
Wide operating / storage TOP / TST -30 70 C
temperature (FSTN)

n ELECTRICAL CHARACTERISTICS ( VDD = +5V 10% , VSS = 0V, Ta = 25°C )

DC Characteristics

Parameter Symbol Condition Min Typ Max Unit

Supply voltage for logic VDD --- 4.5 5.0 5.5 V
Supply current for logic IDD --- --- 400 500 uA
Operating voltage for LCD VDD - VEE 25°C 24.8 26.0 27.2 V
Input voltage ' H ' level VIH --- 0.7VDD --- VDD V
Input voltage ' L ' level VIL --- 0 --- 0.3VDD V
White LED backlight operating Vf 25°C --- 3.6 4.0 V
voltage
White LED backlight forward If 25°C --- 160 320 mA
current
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.4 of 17

AC Electrical Characteristics

Item Symbol Min Typ Max Unit

CL1 pulse width “H” tW 15 --- --- ns
Clock cycle time fCP 50 --- --- ns
CL2 pulse width tWC 15 --- --- ns
Clock set up time tLSU 25 --- --- ns
Clock hole time tLC 25 --- --- ns
Clock rise/fall time tr , tf --- --- 50 ns
Data set up time tDSU 10 --- --- ns
Data hold time tDHD 12 --- --- ns
' M ' set up time tSETUP 25 --- --- ns
' M ' hold time tHOLD 25 --- --- ns

fCP
tW tW tW
tf tr

0.8VDD
CL2
0.2VDD

tDSU tDHD

D0~D3 0.8VDD
0.2VDD

tLSU tLC

0.8VDD
CL1
0.2VDD

tr tWC tf
tSETUP tHOLD

0.8VDD
M
0.2VDD
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.5 of 17

n TIMING CHART OF INPUT SIGNALS

FLM

Row No. 319 320 1 2 3 4 317 318 319 320 1 2

CL1

Enlarged
CL1

CL2

D3 233 237 1 5 ----------------------------- 233 237 1

D2 234 238 2 6 ----------------------------- 234 238 2
D1 235 239 3 7 ----------------------------- 235 239 3
D0 236 240 4 8 ----------------------------- 236 240 4

n DISPLAY DATA PATTERN

S1 S2 S3 S4 S5 S236 S237 S238 S239 S240 SEG
C1 D3 D2 D1 D0 D3 D0 D3 D2 D1 D0
C2 D3 D2 D1 D0 D3 D0 D3 D2 D1 D0

Input data Dots on display

D0 Dot 4 Dot 8 Dot 236 Dot 240
D1 Dot 3 Dot 7 Dot 235 Dot 239
D2 Dot 2 Dot 6 Dot 234 Dot 238
D3 Dot 1 Dot 5 Dot 233 Dot 237

C319 D3 D2 D1 D0 D3 D0 D3 D2 D1 D0
C320 D3 D2 D1 D0 D3 D0 D3 D2 D1 D0
COM
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.6 of 17

n TIMING OF POWER SUPPLY

4.75V
VDD
GND 0~200ms 0~200ms

CL1
GND
0ms 0ms

VEE
GND
20ms 20ms

/D.OFF
GND

POWER ON POWER OFF

Note : The missing pixels may occur when the LCM is

driven except above power supply timing sequence.

n EXAMPLE OF POWER CONNECTION

VDD
+5.0V

LCM VSS
+20.8V

VEE
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.7 of 17

n ELECTRO-OPTICAL CHARACTERISTICS ( VOP = 26.0V, Ta = 25°C )

Typ response Typ response Typ viewing angle (deg)
time Tr (ms) time Tf (ms) Typ contrast
LCD mode
Normal Wide Normal Wide ratio Cr =0 = 90 = 180 = 270
temp temp temp temp
STN Y/G (B) 14 55 30 34 28
STN Blue (C) 4 47 24 29 23
STN Grey (D) 331 167 91 66 7 54 28 32 28
FSTN (F) 21 60 45 53 43
FSTN Negative (G) 9 48 24 30 23

Note 1. Definition of response time

Note 2. Definition of Contrast Ratio ‘Cr’ Note 3. Definition of Viewing Angle Range ‘ ’
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.8 of 17

n INTERFACE PIN CONNECTIONS

Pin No. Symbol Level Description
1 V5 --- Power supply pin for LCD driver voltage bias (VSS<V5<V4<V3<V2<VEE)
2 V2 --- Power supply pin for LCD driver voltage bias (VSS<V5<V4<V3<V2<VEE)
3 VEE --- Power supply pin for LCD driver voltage
4 VDD +5V Logic system power supply pin
5 FLM H/L Frame signal pin
6 VSS 0V Ground
7 CL1 H/L Latch pulse input pin for display data
8 VSS 0V Ground
9 M H/L AC signal input for LCD driving waveform
10 /D.OFF L Control input pin for output deselect level
11 CL2 H/L Clock input pin for taking display data
12 V4 --- Power supply pin for lcd driver voltage bias (VSS<V5<V4<V3<V2<VEE)
13 V3 --- Power supply pin for lcd driver voltage bias (VSS<V5<V4<V3<V2<VEE)
14 D3 H/L Data bit 4
15 D2 H/L Data bit 3
16 D1 H/L Data bit 2
17 D0 H/L Data bit 1
18 NC --- No connection
19 T/P(X2) --- No connection
20 T/P(Y1) --- No connection
21 T/P(X1) --- No connection
22 T/P(Y2) --- No connection
23 A 3.6V White LED backlight anode
24 K 0V White LED backlight cathode
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.9 of 17

n CIRCUIT DIAGRAM
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.10 of 17
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.11 of 17

n RELIABILITY

Content of Reliability Test

Environmental Test
No. Test Item Content of Test Test Condition Applicable
Standard
1 High temperature Endurance test applying the high storage 60 C ------
storage temperature for a long time. 200 hrs
2 Low temperature Endurance test applying the low storage -10 C ------
storage temperature for a long time. 200 hrs
3 High temperature Endurance test applying the electric stress 50 C
operation (Voltage & Current) and the thermal stress to 200 hrs ------
the element for a long time.
4 Low temperature Endurance test applying the electric stress 0 C ------
operation under low temperature for a long time. 200 hrs
5 High temperature Endurance test applying the high temperature 60 C , 90 RH MIL-202E-103B
Humidity storage and high humidity storage for a long time. 96 hrs JIS-C5023
6 High temperature Endurance test applying the electric stress 50 C , 90 RH MIL-202E-103B
Humidity operation (Voltage & Current) and temperature 96 hrs JIS-C5023
humidity stress to the element for a long time.
7 Temperature cycle Endurance test applying the low and high -10 C 60 C
temperature cycle. 10 cycles
-10 C 25 C 60 C ------
30min 5min. 30min
. 1 cycle .

Mechanical Test
8 Vibration test Endurance test applying the vibration during 10 22Hz 1.5mmp-p MIL-202E-201A
transportation and using. 22 500Hz 1.5G JIS-C5025
Total 0.5hrs JIS-C7022-A-10
9 Shock test Constructional and mechanical endurance test 50G half sign MIL-202E-213B
applying the shock during transportation. wave 1l msedc
3 times of each
direction
10 Atmospheric Endurance test applying the atmospheric 115 mbar MIL-202E-105C
pressure test pressure during transportation by air. 40 hrs
Others
11 Static electricity test Endurance test applying the electric stress to VS=800V , RS=1.5 k MIL-883B-
the terminal. CS=100 pF 3015.1
1 time
Supply voltage for logic system = VDD. Supply voltage for LCD system = Operating voltage at 25 C.

Failure Judgement Criterion

Criterion Item Test Item No. Failure Judgment Criterion
1 2 3 4 5 6 7 8 9 10 11
Basic specification Out of the Basic Specification
Electrical characteristic Out of the DC and AC Characterstic
Mechanical characterstic Out of the Mechanical Specification Color
change : Out of Limit Apperance Specification
Optical characterstic Out of the Apperance Standard
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.12 of 17

n QUALITY GUARANTEE

Acceptable Quality Level

Each lot should satisfy the quality level defined as follows.
- Inspection method : MIL-STD-105E LEVEL II Normal one time sampling
- AQL
Partition AQL Definition
A: Major 0.4% Functional defective as product
B: Minor 1.5% Satisfy all functions as product but not satisfy cosmetic standard

Definition of ‘LOT’
One lot means the delivery quantity to customer at one time.

Conditions of Cosmetic Inspection

l Environmental condition
The inspection should be performed at the 1m of height from the LCD module under 2 pieces of 40W white
fluorescent lamps (Normal temperature 20 25 C and normal humidity 60 15 RH).
l Inspection method
The visual check should be performed vertically at more than 30cm distance from the LCD panel.
l Driving voltage
The VO value which the most optimal contrast can be obtained near the specified VO in the specification. (Within
0.5V of the typical value at 25 C.).

n INSPECTION CRITERIA
Module Cosmetic Criteria
No. Item Judgement Criterion Partition
1 Difference in Spec. None allowed Major
2 Pattern peeling No substrate pattern peeling and floating Major
3 Soldering defects No soldering missing Major
No soldering bridge Major
No cold soldering Minor
4 Resist flaw on substrate Invisible copper foil ( 0.5mm or more) on substrate pattern Minor
5 Accretion of metallic No soldering dust Minor
Foreign matter No accretion of metallic foreign matters (Not exceed 0.2mm) Minor
6 Stain No stain to spoil cosmetic badly Minor
7 Plate discoloring No plate fading, rusting and discoloring Minor
8 Solder amount a. Soldering side of PCB Minor
Solder to form a ‘Filet’
1. Lead parts all around the lead.
Solder should not hide the
lead form perfectly. (too much)
b. Components side
( In case of ‘Through Hole PCB’ )

Solder to reach the Components side of PCB.

2. Flat packages Either ‘toe’ (A) or ‘heal’ (B) of Minor
the lead to be covered by ‘Filet’. A B
Lead form to be assume over
solder.
3. Chips (3 2) H h (1 2) H Minor
h H
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.13 of 17

Screen Cosmetic Criteria (Non-Operating)

No. Defect Judgement Criterion Partition
1 Spots In accordance with Screen Cosmetic Criteria (Operating) No.1. Minor
2 Lines In accordance with Screen Cosmetic Criteria (Operating) No.2. Minor
3 Bubbles in polarizer Minor
Size : d mm Acceptable Qty in active area
d 0.3 Disregard
0.3 d 1.0 3
1.0 d 1.5 1
1.5 d 0

4 Scratch In accordance with spots and lines operating cosmetic criteria. When the light Minor
reflects on the panel surface, the scratches are not to be remarkable.
5 Allowable density Above defects should be separated more than 30mm each other. Minor
6 Coloration Not to be noticeable coloration in the viewing area of the LCD panels. Minor
Back-lit type should be judged with back-lit on state only.
7 Contamination Not to be noticeable. Minor

Screen Cosmetic Criteria (Operating)

No. Defect Judgement Criterion Partition
1 Spots A) Clear Minor
Size : d mm Acceptable Qty in active area
d 0.1 Disregard
0.1 d 0.2 6
0.2 d 0.3 2
0.3 d 0
Note : Including pin holes and defective dots which must be within one pixel
size.
B) Unclear
Size : d mm Acceptable Qty in active area
d 0.2 Disregard
0.2 d 0.5 6
0.5 d 0.7 2
0.7 d 0

2 Lines A) Clear Minor

L 5.0 (0)

2.0 (6) See No. 1

W
0.02 0.05 0.1
Note : ( ) - Acceptable Qty in active area
L - Length (mm)
W - Width (mm)
- Disregard
B) Unclear
L 10.0 (0)

(6)

2.0 See No. 1

W
0.05 0.3 0.5

‘Clear’ = The shade and size are not changed by VO.

‘Unclear’ = The shade and size are changed by VO.
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.14 of 17

Screen Cosmetic Criteria (Operating) (Continued)

No. Defect Judgement Criterion Partition
3 Rubbing line Not to be noticeable.
4 Allowable density Above defects should be separated more than 10mm each other. Minor
5 Rainbow Not to be noticeable. Minor
6 Dot size To be 95 105 of the dot size (Typ.) in drawing. Minor
Partial defects of each dot (ex. pin-hole) should be treated as ‘spot’.
(see Screen Cosmetic Criteria (Operating) No.1)
7 Uneven brightness Uneven brightness must be BMAX BMIN 2 Minor
(only back-lit type - BMAX : Max. value by measure in 5 points
module) - BMIN : Min. value by measure in 5 points
Divide active area into 4 vertically and horizontally.
Measure 5 points shown in the following figure.

¡ ¡

¡ ¡

¡ : Measuring points

Note :
(1) Size : d = (long length short length) 2
(2) The limit samples for each item have priority.
(3) Complexed defects are defined item by item, but if the number of defects are defined in above table, the total number
should not exceed 10.
(4) In case of ‘concentration’, even the spots or the lines of ‘disregarded’ size should not allowed. Following three
situations should be treated as ‘concentration’.
- 7 or over defects in circle of 5mm.
- 10 or over defects in circle of 10mm.
- 20 or over defects in circle of 20mm.

n PRECAUTIONS FOR USING LCD MODULES

Handing Precautions
(1) The display panel is made of glass. Do not subject it to a mechanical shock by dropping it or impact.
(2) If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth. If the
substance contacts your skin or clothes, wash it off using soap and water.
(3) Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary.
(4) The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer
carefully.
(5) If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If it is
heavily contaminated, moisten cloth with one of the following solvents :
- Isopropyl alcohol
- Ethyl alcohol
(6) Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the following.
- Water
- Ketone
- Aromatic solvents
(7) Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by water droplets,
moisture condensation or a current flow in a high-humidity environment.
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.15 of 17

(8) Install the LCD Module by using the mounting holes. When mounting the LCD module make sure it is free of
twisting, warping and distortion. In particular, do not forcibly pull or bend the I O cable or the backlight cable.
(9) Do not attempt to disassemble or process the LCD module.
(10) NC terminal should be open. Do not connect anything.
(11) If the logic circuit power is off, do not apply the input signals.
(12) To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment.
- Be sure to ground the body when handling the LCD modules.
- Tools required for assembling, such as soldering irons, must be properly grounded.
- To reduce the amount of static electricity generated, do not conduct assembling and other work under dry
conditions.
- The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this protective
film since static electricity may be generated.

Storage Precautions
When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. Keep the modules
in bags (avoid high temperature high humidity and low temperatures below 0 C). Whenever possible, the LCD modules
should be stored in the same conditions in which they were shipped from our company.

Others
Liquid crystals solidify under low temperature (below the storage temperature range) leading to defective orientation or
the generation of air bubbles (black or white). Air bubbles may also be generated if the module is subject to a low
temperature.
If the LCD modules have been operating for a long time showing the same display patterns, the display patterns may
remain on the screen as ghost images and a slight contrast irregularity may also appear. A normal operating status can be
regained by suspending use for some time. It should be noted that this phenomenon does not adversely affect performance
reliability.
To minimize the performance degradation of the LCD modules resulting from destruction caused by static electricity
etc., exercise care to avoid holding the following sections when handling the modules.
- Exposed area of the printed circuit board.
- Terminal electrode sections.

n USING LCD MODULES

Liquid Crystal Display Modules

LCD is composed of glass and polarizer. Pay attention to the following items when handling.
(1) Please keep the temperature within specified range for use and storage. Polarization degradation, bubble generation
or polarizer peel-off may occur with high temperature and high humidity.
(2) Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass, tweezers, etc.).
(3) N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and reflectors made of
organic substances which will be damaged by chemicals such as acetone, toluene, ethanol and isopropylalcohol.
(4) When the display surface becomes dusty, wipe gently with absorbent cotton or other soft material like chamois soaked
in petroleum benzin. Do not scrub hard to avoid damaging the display surface.
(5) Wipe off saliva or water drops immediately, contact with water over a long period of time may cause deformation or
color fading.
(6) Avoid contacting oil and fats.
(7) Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the polarizers. After
products are tested at low temperature they must be warmed up in a container before coming is contacting with room
temperature air.
(8) Do not put or attach anything on the display area to avoid leaving marks on.
(9) Do not touch the display with bare hands. This will stain the display area and degradate insulation between terminals
(some cosmetics are determinated to the polarizers).
(10) As glass is fragile. It tends to become or chipped during handling especially on the edges. Please avoid dropping or
jarring.
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.16 of 17

Installing LCD Modules

The hole in the printed circuit board is used to fix LCM as shown in the picture below. Attend to the following items
when installing the LCM.
(1) Cover the surface with a transparent protective plate to protect the polarizer and LC cell.

(2) When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting plate should
have enough height to avoid causing stress to the module surface, refer to the individual specifications for measurements.
The measurement tolerance should be 0.1mm.

Precaution for Handing LCD Modules

Since LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the
module or making any alterations or modifications to it.
(1) Do not alter, modify or change the the shape of the tab on the metal frame.
(2) Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to be
attached.
(3) Do not damage or modify the pattern writing on the printed circuit board.
(4) Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector.
(5) Except for soldering the interface, do not make any alterations or modifications with a soldering iron.
(6) Do not drop, bend or twist LCM.

Electro-Static Discharge Control

Since this module uses a CMOS LSI, the same careful attention should be paid to electrostatic discharge as for an
ordinary CMOS IC.
(1) Make certain that you are grounded when handing LCM.
(2) Before remove LCM from its packing case or incorporating it into a set, be sure the module and your body have the
same electric potential.
(3) When soldering the terminal of LCM, make certain the AC power source for the soldering iron does not leak.
(4) When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize as
much as possible any transmission of electromagnetic waves produced sparks coming from the commutator of the motor.
(5) As far as possible make the electric potential of your work clothes and that of the work bench the ground potential.
(6) To reduce the generation of static electricity be careful that the air in the work is not too dried. A relative humidity of
50%-60% is recommended.

Precaution for soldering to the LCM

(1) Observe the following when soldering lead wire, connector cable and etc. to the LCM.
- Soldering iron temperature : 280 C 10 C.
- Soldering time : 3-4 sec.
- Solder : eutectic solder.
If soldering flux is used, be sure to remove any remaining flux after finishing to soldering operation. (This does not
apply in the case of a non-halogen type of flux.) It is recommended that you protect the LCD surface with a cover during
soldering to prevent any damage dur to flux spatters.
(2) When soldering the electroluminescent panel and PC board, the panel and board should not be detached more than
three times. This maximum number is determined by the temperature and time conditions mentioned above, though there
may be some variance depending on the temperature of the soldering iron.
(3) When remove the electoluminescent panel from the PC board, be sure the solder has completely melted, the soldered
pad on the PC board could be damaged.
Displaytech Ltd LCD MODULE 240320D SERIES Version : 1.0 P.17 of 17

Precautions for Operation

(1) Viewing angle varies with the change of liquid crystal driving voltage (VO). Adjust VO to show the best contrast.
(2) Driving the LCD in the voltage above the limit shortens its life.
(3) Response time is greatly delayed at temperature below the operating temperature range. However, this does not mean
the LCD will be out of the order. It will recover when it returns to the specified temperature range.
(4) If the display area is pushed hard during operation, the display will become abnormal. However, it will return to
normal if it is turned off and then back on.
(5) Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit. Therefore, it must
be used under the relative condition of 40 C , 50% RH.
(6) When turning the power on, input each signal after the positive/negative voltage becomes stable.

Storage
When storing LCDs as spares for some years, the following precaution are necessary.
(1) Store them in a sealed polyethylene bag. If properly sealed, there is no need for dessicant.
(2) Store them in a dark place. Do not expose to sunlight or fluorescent light, keep the temperature between 0 C and
35 C.
(3) The polarizer surface should not come in contact with any other objects. (We advise you to store them in the
container in which they were shipped.)
(4) Environmental conditions :
- Do not leave them for more than 168hrs. at 60 C.
- Should not be left for more than 48hrs. at -20 C.

Safety
(1) It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with solvents such as
acetone and ethanol, which should later be burned.
(2) If any liquid leakes out of a damaged glass cell and comes in contact with the hands, wash off thoroughly with soap
and water.

Limited Warranty
Unless agreed between DISPLAYTECH and customer, DISPLAYTECH will replace or repair any of its LCD modules
which are found to be functionally defective when inspected in accordance with DISPLAYTECH LCD acceptance standards
(copies available upon request) for a period of one year from date of shipments. Cosmetic/visual defects must be returned to
DISPLAYTECH within 90 days of shipment. Confirmation of such date shall be based on freight documents. The warranty
liability of DISPLAYTECH limited to repair and/or replacement on the terms set forth above. DISPLAYTECH will not be
responsible for any subsequent or consequential events.

Return LCM under warranty

No warranty can be granted if the precautions stated above have been disregarded. The typical examples of violations
are:
- Broken LCD glass.
- PCB eyelet’s damaged or modified.
- PCB conductors damaged.
- Circuit modified in any way, including addition of components.
- PCB tampered with by grinding, engraving or painting varnish.
- soldering to or modifying the bezel in any manner.
Module repairs will be invoiced to the customer upon mutual agreement. Modules must be returned with sufficient
description of the failures or defects. Any connectors or cable installed by the customer must be removed completely without
damaging the PCB eyelet’s, conductors and terminals.