100% found this document useful (2 votes)
292 views3 pages

FINAL On PSP

This document contains instructions and questions for a final exam on power system protection and control. It is divided into three parts: explanatory questions, multiple choice, and workout problems. The explanatory questions cover causes of CT errors, CT burden and composite error, characteristics of Rogowski coils, and advantages and disadvantages of CCVTs. The multiple choice questions test knowledge of different relay types. The workout problems involve determining backup protection schemes, CT specifications, and settings for motor overload protection.

Uploaded by

daveade
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
100% found this document useful (2 votes)
292 views3 pages

FINAL On PSP

This document contains instructions and questions for a final exam on power system protection and control. It is divided into three parts: explanatory questions, multiple choice, and workout problems. The explanatory questions cover causes of CT errors, CT burden and composite error, characteristics of Rogowski coils, and advantages and disadvantages of CCVTs. The multiple choice questions test knowledge of different relay types. The workout problems involve determining backup protection schemes, CT specifications, and settings for motor overload protection.

Uploaded by

daveade
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Dire Dawa University Institute of Technology [DDUIOT]

School of Electrical and Computer Engineering


Power Engineering Stream
Final Exam: 50% Semester: I Year: IV

Full Name: ___________ ID: __________________

Course Name: Power System Protection and Control Course Code: ECEG-4232

Name of Instructors: Dawit Adane Email: [email protected]

Exam Date: 13/6/2015 Duration of Exam: 180 minutes

Number of exam pages including cover page: 3 Exam type: closed

General Instructions:

 Please read each question carefully and write your answers legibly in the attached paper
 The exchanging information in the exam hall through symbolic, written or electronic device is forbidden.
 Write the question number properly, answer will not be evaluated without question number
 Keep your work neat and clear
 You can use both side of answer sheet
 Attempt all questions
 Neat diagrams must be drawn wherever necessary.
 Switch off your mobile phone; only scientific calculator is allowed

For instructor Used Only [Marking Scheme]

Part-I Part-II Part-III Final Exam Continuous Total


Explanatory Choice Workout (50%) Assessment (100%)
(26 points) (6 points) (18 points) (50%)
Part I: Explanatory Type Questions (26 pts)
1. Discuss the causes of ratio and phase angle errors in CTs. How can these errors be minimized? (5 pts)
2. What is meant by ‘burden’ and ‘composite error’ of a CT? (5 pts)
3. Describe the characteristics of the Rogowski coil current sensor.? (5 pts)
4. What is the advantage and disadvantage of CCVT? (5 pts)
5. Explain about attraction type electromagnetic relays? (6 pts)

Part II: Multiple Choice Questions (6 pts)


1. Which one of relay is that operates when the phasor difference of two or more similar electrical quantities
exceeds a pre-determined value.?
(a) Differential relay (b) Over current relay
(c) Distance relay (d) Directional relay
2. The material mostly preferred as core of protective CTs is
(a) nickel–iron (b) hot-rolled non-oriented silicon steel
(c) cold-rolled oriented silicon steel (d) none of the above
3. The burden of an overcurrent relay is helpful in deciding
(a) transformation ratio of a CT (b) volt–ampere rating of a CT
(c) transformation ratio of a PT (d) volt–ampere rating of a PT
Part III: Workout Questions (18 pts)
1. Determine the possible local and remote back-up protection for a fault location as shown in the Figure
below? Assume that breaker I, breaker L and breaker M failed to operate. (8 pts)
2. A small power plant consists of three 5 MVA, 6.6 kV, 3-phase, 50 Hz alternators with 20% reactance,
each connected to a common busbar. The busbar supplies a number of feeders, on each of which are
installed CTs with details as follows:

CT ratio = 600/5 A
CT secondary resistance = 0.8 ohm
Burden impedance = 1.2 ohms
Neglecting the lead burden and assuming that no generating source exists at the far ends of the feeders,
specify (10 pts)

(a) the secondary voltage up to which the CTs should not saturate (knee-point voltage)
(b) accuracy limit factor and accuracy class
(c) rated burden of the CT

3. An induction motor is to be protected against overload. Nameplate details are 3-phase, 6.6 kV, 1250 kW,
0.8 p.f. The motor can withstand 15% overload continuously. A thermal relay is connected across a C.T.
of 200/1 ratio. The time constant of the relay is also 10 minutes. The range of settings is 70 –130% of 1 A
in steps of 5%. Determine (Bonus)
(a) The relay current setting in %
(b) The relay Plug setting multiplier if the fault current is 1571.82 A
(c) The operating time of relay if the time setting multiplier is 0.05 and the following graph is
Time/PSM curve

You might also like