Safety Data Sheet

SECTION 1 PRODUCT AND COMPANY IDENTIFICATION

Chevron SRI Grease 2

Product Use: Industrial Grease
Product Number(s): 219586, 254521
Company Identification
Chevron Canada Limited
500 - 5th Ave. SW
Calgary, ALBERTA T2P 0L7
Canada
www.chevronlubricants.com

Transportation Emergency Response

CHEMTREC: (800) 424-9300 or (703) 527-3887
Health Emergency
Chevron Emergency & Information Center: Located in the USA. International collect calls accepted.
(800) 231-0623 or (510) 231-0623
Product Information
email : [email protected]
Product Information: (800) LUBE TEK

SECTION 2 HAZARDS IDENTIFICATION

CLASSIFICATION:

• Skin Sensitizer: Category 1.

• Acute aquatic toxicant: Category 3.
• Chronic aquatic toxicant: Category 3.

Signal Word: Warning

Health Hazards:
• May cause an allergic skin reaction (H317).

Environmental Hazards:
• Harmful to aquatic life with long lasting effects (H412).

PRECAUTIONARY STATEMENTS:
Prevention:
• Avoid breathing dust/fume/gas/mist/vapours/spray (P261).

_____________________________________________________________________
Revision Number: 6 1 of 8 Chevron SRI Grease 2
Revision Date: October 24, 2022 SDS : 36501
• Contaminated work clothing should not be allowed out of the workplace (P272).
• Avoid release to the environment (P273).
• Wear protective gloves/protective clothing/eye protection/face protection (P280).
Response:
• IF ON SKIN: Wash with plenty of soap and water (P302+P352).
• Specific treatment (see Notes to Physician on this label) (P321).
• If skin irritation or rash occurs: Get medical advice/attention (P333+P313).
• Take off contaminated clothing and wash it before reuse (P362+P364).
Disposal:
• Dispose of contents/container in accordance with applicable local/regional/national/international
regulations (P501).

SECTION 3 COMPOSITION/ INFORMATION ON INGREDIENTS

COMPONENTS CAS NUMBER AMOUNT

Highly refined mineral oil (C15 - C50) Mixture 80 - 100 %wt/wt
3,3'-Dicyclohexyl-1,1'-methylenebis(4,1- 58890-25-8 5 - 10 %wt/wt
phenylene)diurea
Succinic anhydride, alkylation products with C12-rich Not Available 1 - 5 %wt/wt
branched olefins from propene oligomerisation,
hydrolyzed, esterification products with propylene
oxide
Polymerized 1,2-dihydro-2,2,4-trimethylquinoline 26780-96-1 1 - 5 %wt/wt
Note that the actual concentration or concentration range of some or all of the above ingredients is
considered confidential business information and is being withheld as permitted by WHMIS 2015.

SECTION 4 FIRST AID MEASURES

Description of first aid measures

Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and
flush eyes with water.
Skin: Wash skin with water immediately and remove contaminated clothing and shoes. Get medical
attention if any symptoms develop. To remove the material from skin, use soap and water. Discard
contaminated clothing and shoes or thoroughly clean before reuse.
Ingestion: No specific first aid measures are required. Do not induce vomiting. As a precaution, get
medical advice.
Inhalation: No specific first aid measures are required. If exposed to excessive levels of material in the
air, move the exposed person to fresh air. Get medical attention if coughing or respiratory discomfort
occurs.

Most important symptoms and effects, both acute and delayed

IMMEDIATE HEALTH EFFECTS
Eye: Not expected to cause prolonged or significant eye irritation.
Skin: Contact with the skin may cause an allergic skin reaction. Symptoms may include pain, itching,
discoloration, swelling, and blistering. High-Pressure Equipment Information: Accidental high-velocity
injection under the skin of materials of this type may result in serious injury. Seek medical attention at
once should an accident like this occur. The initial wound at the injection site may not appear to be
serious at first; but, if left untreated, could result in disfigurement or amputation of the affected part.
Contact with the skin is not expected to cause prolonged or significant irritation.
Ingestion: Not expected to be harmful if swallowed.
Inhalation: Not expected to be harmful if inhaled. Contains a petroleum-based mineral oil. May cause
respiratory irritation or other pulmonary effects following prolonged or repeated inhalation of oil mist at
airborne levels above the recommended mineral oil mist exposure limit. Symptoms of respiratory
irritation may include coughing and difficulty breathing.
_____________________________________________________________________
Revision Number: 6 2 of 8 Chevron SRI Grease 2
Revision Date: October 24, 2022 SDS : 36501
Indication of any immediate medical attention and special treatment needed
Note to Physicians: In an accident involving high-pressure equipment, this product may be injected
under the skin. Such an accident may result in a small, sometimes bloodless, puncture wound.
However, because of its driving force, material injected into a fingertip can be deposited into the palm of
the hand. Within 24 hours, there is usually a great deal of swelling, discoloration, and intense throbbing
pain. Immediate treatment at a surgical emergency center is recommended.

SECTION 5 FIRE FIGHTING MEASURES

EXTINGUISHING MEDIA: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish
flames.
Unusual Fire Hazards: Leaks/ruptures in high pressure system using materials of this type can create a
fire hazard when in the vicinity of ignition sources (eg. open flame, pilot lights, sparks, or electric arcs).

PROTECTION OF FIRE FIGHTERS:

Fire Fighting Instructions: This material will burn although it is not easily ignited. See Section 7 for
proper handling and storage. For fires involving this material, do not enter any enclosed or confined fire
space without proper protective equipment, including self-contained breathing apparatus.
Combustion Products: Highly dependent on combustion conditions. A complex mixture of airborne
solids, liquids, and gases including carbon monoxide, carbon dioxide, and unidentified organic
compounds will be evolved when this material undergoes combustion. Combustion may form oxides of:
Nitrogen.

SECTION 6 ACCIDENTAL RELEASE MEASURES

Protective Measures: Eliminate all sources of ignition in vicinity of spilled material.

Spill Management: Stop the source of the release if you can do it without risk. Contain release to
prevent further contamination of soil, surface water or groundwater. Clean up spill as soon as possible,
observing precautions in Exposure Controls/Personal Protection. Use appropriate techniques such as
applying non-combustible absorbent materials or pumping. Where feasible and appropriate, remove
contaminated soil. Place contaminated materials in disposable containers and dispose of in a manner
consistent with applicable regulations.
Reporting: Report spills to local authorities as appropriate or required.

SECTION 7 HANDLING AND STORAGE

General Handling Information: Avoid contaminating soil or releasing this material into sewage and
drainage systems and bodies of water.
Precautionary Measures: DO NOT USE IN HIGH PRESSURE SYSTEMS in the vicinity of flames,
sparks and hot surfaces. Use only in well ventilated areas. Keep container closed. Do not get in
eyes, on skin, or on clothing. Wash thoroughly after handling. Keep out of the reach of children.
Static Hazard: Electrostatic charge may accumulate and create a hazardous condition when handling
this material. To minimize this hazard, bonding and grounding may be necessary but may not, by
themselves, be sufficient. Review all operations which have the potential of generating and accumulating
an electrostatic charge and/or a flammable atmosphere (including tank and container filling, splash filling,
tank cleaning, sampling, gauging, switch loading, filtering, mixing, agitation, and vacuum truck operations)
and use appropriate mitigating procedures.
Container Warnings: Container is not designed to contain pressure. Do not use pressure to empty
container or it may rupture with explosive force. Empty containers retain product residue (solid, liquid,
and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose
such containers to heat, flame, sparks, static electricity, or other sources of ignition. They may explode
and cause injury or death. Empty containers should be completely drained, properly closed, and
promptly returned to a drum reconditioner or disposed of properly.

_____________________________________________________________________
Revision Number: 6 3 of 8 Chevron SRI Grease 2
Revision Date: October 24, 2022 SDS : 36501
 SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION

GENERAL CONSIDERATIONS:
Consider the potential hazards of this material (see Section 2), applicable exposure limits, job activities,
and other substances in the workplace when designing engineering controls and selecting personal
protective equipment (PPE). If engineering controls or work practices are not adequate to prevent
exposure to harmful levels of this material, refer to PPE information below.

Factors that affect PPE include, but are not limited to: properties of the chemical, other chemicals which
may contact the same PPE, physical requirements (fit & sizing, cut/puncture protection, dexterity, thermal
protection, etc.), and potential allergic reactions to the PPE material. It is the responsibility of the user to
read and understand all instructions and limitations supplied with the equipment since protection is
usually provided for a limited time or under certain circumstances. Refer to appropriate CEN standards.

ENGINEERING CONTROLS:
Use in a well-ventilated area.

PERSONAL PROTECTIVE EQUIPMENT

Eye/Face Protection: Wear protective equipment to prevent eye contact. Selection of protective
equipment may include safety glasses, chemical goggles, face shields, or a combination depending on
the work operations conducted.
Skin Protection: Wear chemical personal protective equipment (PPE) to prevent skin contact. Selection
of chemical protective clothing should be performed by an Occupational Hygienist or Safety Professional
and be based upon applicable standards (ASTM F739 or EN 374). Using chemical PPE depends upon
operations conducted and may include chemical gloves, boots, chemical apron, chemical suit, and
complete facial protection. Refer to PPE manufacturers to obtain breakthrough time information to
determine how long PPE can be used before it needs to be replaced. Unless specific glove
manufacturer data indicates otherwise, the below table is based upon available industry data to assist in
the glove selection process and is intended to be used as reference only.

Chemical Glove Material Thickness Typical Breakthrough Time

(mm) (minutes)
Butyl 0.7 120
Neoprene 0.61 120
Nitrile 0.8 120
Polyvinyl Chloride (PVC) 1.1 120
Viton Butyl 0.3 120

Respiratory Protection: No respiratory protection is normally required.

If user operations generate an oil mist, determine if airborne concentrations are below the occupational
exposure limit for mineral oil mist. If not, wear an approved respirator that provides adequate protection
from the measured concentrations of this material. For air-purifying respirators use a particulate
cartridge.
Use a positive pressure air-supplying respirator in circumstances where air-purifying respirators may not
provide adequate protection.
Occupational Exposure Limits:

Component Country/ Form TWA STEL Ceiling Notation

Agency
Highly refined mineral oil ACGIH -- 5 mg/m3 10 mg/m3 -- --
(C15 - C50)
NOTE ON OCCUPATIONAL EXPOSURE LIMITS: Consult local authorities for acceptable provincial
values in Canada. Consult the Canadian Standards Association Standard Z94.4-2011 Selection, Use

_____________________________________________________________________
Revision Number: 6 4 of 8 Chevron SRI Grease 2
Revision Date: October 24, 2022 SDS : 36501
and Care of Respirators.

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES

Attention: the data below are typical values and do not constitute a specification.

Color: Dark green

Physical State: Semi-solid
Odor: Petroleum odor
Odor Threshold: Not available
pH: Not Applicable
Vapor Pressure: Not available
Vapor Density (Air = 1): Not available
Initial Boiling Point: Not available
Solubility: Soluble in hydrocarbons; insoluble in water
Freezing Point: Not available
Melting Point: Not available
Specific Gravity: 0.90 @ 15.6°C (60°F) (Typical)
Density: Not available
Viscosity: 11.80 mm2/s @ 100°C (212°F) (Minimum)
Evaporation Rate: Not available
Decomposition temperature: Not available
Octanol/Water Partition Coefficient: Not available

FLAMMABLE PROPERTIES:
Flammability (solid, gas): Not Available

Flashpoint: (Cleveland Open Cup) 204 °C (399 °F) (Minimum)

Autoignition: Not available
Flammability (Explosive) Limits (% by volume in air): Lower: Not Applicable Upper: Not
Applicable

SECTION 10 STABILITY AND REACTIVITY

Reactivity: May react with strong acids or strong oxidizing agents, such as chlorates, nitrates,
peroxides, etc.
Chemical Stability: This material is considered stable under normal ambient and anticipated storage
and handling conditions of temperature and pressure.
Incompatibility With Other Materials: Not applicable
Hazardous Decomposition Products: None known (None expected)
Hazardous Polymerization: Hazardous polymerization will not occur.
Sensitivity to Mechanical Impact: No.

SECTION 11 TOXICOLOGICAL INFORMATION

Information on toxicological effects

Serious Eye Damage/Irritation: The material is not considered an eye irritant. The product has not been
tested. The statement is based on evaluation of data for similar materials or product components.
Skin Corrosion/Irritation: The material is not considered a skin irritant. The product has not been tested.
The statement is based on evaluation of data for similar materials or product components.
Skin Sensitization: The material may cause an allergic skin reaction. The product has not been tested.
The statement is based on evaluation of data for similar materials or product components.
Acute Dermal Toxicity: The material is not considered a dermal toxicant. The product has not been
_____________________________________________________________________
Revision Number: 6 5 of 8 Chevron SRI Grease 2
Revision Date: October 24, 2022 SDS : 36501
tested. The statement is based on evaluation of data for similar materials or product components.
Acute Oral Toxicity: The material is not considered an oral toxicant. The product has not been tested.
The statement is based on evaluation of data for similar materials or product components.
Acute Inhalation Toxicity: The material is not considered an inhalation toxicant. The product has not
been tested. The statement is based on evaluation of data for similar materials or product
components.For additional information on the acute toxicity of the components, call the technical
information center.
Acute Toxicity Estimate: Not Determined

Germ Cell Mutagenicity: The material is not considered a mutagen. The product has not been tested.
The statement is based on evaluation of data for similar materials or product components.

Carcinogenicity: The material is not considered a carcinogen. The product has not been tested. The
statement is based on evaluation of data for similar materials or product components.

Reproductive Toxicity: The material is not considered a reproductive toxicant. The product has not been
tested. The statement is based on evaluation of data for similar materials or product components.

Specific Target Organ Toxicity - Single Exposure:

The material is not considered a target organ toxicant (single exposure). The product has not been
tested. The statement is based on evaluation of data for similar materials or product components.
Specific Target Organ Toxicity - Repeated Exposure: The material is not considered a target organ
toxicant (repeated exposure). The product has not been tested. The statement is based on evaluation of
data for similar materials or product components.

Aspiration Hazard: The material is not considered an aspiration hazard.

ADDITIONAL TOXICOLOGY INFORMATION:

This product contains petroleum base oils which may be refined by various processes including severe
solvent extraction, severe hydrocracking, or severe hydrotreating. None of the oils requires a cancer
warning under the OSHA Hazard Communication Standard (29 CFR 1910.1200). These oils have not
been listed in the National Toxicology Program (NTP) Annual Report nor have they been classified by the
International Agency for Research on Cancer (IARC) as; carcinogenic to humans (Group 1), probably
carcinogenic to humans (Group 2A), or possibly carcinogenic to humans (Group 2B).
These oils have not been classified by the American Conference of Governmental Industrial Hygienists
(ACGIH) as: confirmed human carcinogen (A1), suspected human carcinogen (A2), or confirmed animal
carcinogen with unknown relevance to humans (A3).

SECTION 12 ECOLOGICAL INFORMATION

ECOTOXICITY
This material is expected to be harmful to aquatic organisms and may cause long-term adverse effects in
the aquatic environment.
The product has not been tested. The statement has been derived from the properties of the individual
components.

MOBILITY
No data available.

PERSISTENCE AND DEGRADABILITY

This material is not expected to be readily biodegradable. The product has not been tested. The
statement has been derived from the properties of the individual components.

_____________________________________________________________________
Revision Number: 6 6 of 8 Chevron SRI Grease 2
Revision Date: October 24, 2022 SDS : 36501
POTENTIAL TO BIOACCUMULATE
Bioconcentration Factor: No data available.
Octanol/Water Partition Coefficient: No data available

SECTION 13 DISPOSAL CONSIDERATIONS

Use material for its intended purpose or recycle if possible. Oil collection services are available for used
oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner
consistent with applicable regulations. Contact your sales representative or local environmental or
health authorities for approved disposal or recycling methods. (See B.C. Reg. GY/92 Waste
Management Act; R.R.O. 1990, Reg. 347 General-Waste Management; C.C.SM.c. W40 The Waste
Reduction and Prevention Act; N.S. Reg. 51/95 and N.S. Reg. 179/96 for examples of Provincial
legislation.)

SECTION 14 TRANSPORT INFORMATION

The description shown may not apply to all shipping situations. Consult 49CFR, or appropriate
Dangerous Goods Regulations, for additional description requirements (e.g., technical name) and mode-
specific or quantity-specific shipping requirements.

TC Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT UNDER

TRANSPORT CANADA

IMO/IMDG Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT

UNDER THE IMDG CODE

ICAO/IATA Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT

UNDER ICAO

DOT Shipping Description: NOT REGULATED AS HAZARDOUS MATERIAL UNDER 49 CFR

SECTION 15 REGULATORY INFORMATION

REGULATORY LISTS SEARCHED:

01-1=IARC Group 1
01-2A=IARC Group 2A
01-2B=IARC Group 2B

No components of this material were found on the regulatory lists above.

CHEMICAL INVENTORIES:
All components comply with the following chemical inventory requirements: IECSC (China), PICCS
(Philippines), TCSI (Taiwan), TSCA (United States).

One or more components does not comply with the following chemical inventory requirements: ENCS
(Japan).

SECTION 16 OTHER INFORMATION

REVISION STATEMENT: SECTION 04 - Delayed Health Effects - Target Organ(s) information was
modified.
SECTION 05 - Unusual Fire Fighting Hazards information was added.
SECTION 07 - Precautionary Measures information was modified.
SECTION 08 - Eye/Face Protection information was modified.

_____________________________________________________________________
Revision Number: 6 7 of 8 Chevron SRI Grease 2
Revision Date: October 24, 2022 SDS : 36501
SECTION 08 - General Considerations information was modified.
SECTION 08 - Personal Protective Equipment List information was deleted.
SECTION 08 - Personal Protective Equipment information was added.
SECTION 08 - Skin Protection information was modified.

Revision Date: October 24, 2022

ABBREVIATIONS THAT MAY HAVE BEEN USED IN THIS DOCUMENT:

TLV - Threshold Limit Value TWA - Time Weighted Average
STEL - Short-term Exposure Limit PEL - Permissible Exposure Limit
GHS - Globally Harmonized System CAS - Chemical Abstract Service Number
ACGIH - American Conference of IMO/IMDG - International Maritime Dangerous
Governmental Industrial Hygienists Goods Code
API - American Petroleum Institute SDS - Safety Data Sheet
WHMIS - Workplace Hazardous Materials NFPA - National Fire Protection Association
Information System (USA)
DOT - Department of Transportation (USA) NTP - National Toxicology Program (USA)
IARC - International Agency for Research on OSHA - Occupational Safety and Health
Cancer Administration
NCEL - New Chemical Exposure Limit EPA - Environmental Protection Agency
SCBA - Self-Contained Breathing Apparatus

Prepared according to the WHMIS 2015 by Chevron Technical Center, 6001 Bollinger Canyon Road, San
Ramon, CA 94583.

The above information is based on the data of which we are aware and is believed to be correct
as of the date hereof. Since this information may be applied under conditions beyond our
control and with which we may be unfamiliar and since data made available subsequent to the
date hereof may suggest modifications of the information, we do not assume any responsibility
for the results of its use. This information is furnished upon condition that the person
receiving it shall make his own determination of the suitability of the material for his particular
purpose.

_____________________________________________________________________
Revision Number: 6 8 of 8 Chevron SRI Grease 2
Revision Date: October 24, 2022 SDS : 36501