Section A Pipe

Material Specification Manual Section A: Pipe
Effective Date: 01-01-23

Section A: Pipe
A1 PVC Pipe - Schedule 40
A2 PVC Pipe - Schedule 80
A3 Polyethylene Service Tubing
A 3.1 Polyethylene 2” Potable Water Main Tubing
A 3.2 High Density Polyethylene Pipe (HDPE)
A4 PVC Pipe (2" & 3” SDR-21)
A5 PVC Pipe (AWWA C – 900) – Potable Water (4” thru 24”)
A 5.1 PVC Pipe (AWWA C – 900) – Sewer (4” thru 24”)
A 5.2 PVC Pipe Restrained Joint Pipe & Couplings (AWWA C – 900) (4” thru 16”)
A 5.3 PVC Pipe Fusible (AWWA C-900) - Potable Water (4” thru 24”)
A 5.3.1 PVC Pipe Fusible (AWWA C-900) - Sewer Force Main (4” thru 24”)
A6 Ductile Iron Pipe/ Push-On Joint/ Class 350 (3” thru 36”)
A 6.1 Ductile Iron Pipe/ Flanged Joint/ Class 53
A 6.2 Ductile Iron Pipe/ Restrained Push-On Joint/ TR Flex Joint (3” thru 36”)
A 6.3 Ductile Iron Pipe/ Restrained Push-On Joint/ Flex- Ring Joint (3” thru 48”)
A7 Stainless Steel Pipe
A8 Galvanized Pipe (Temporary)


A 1 – PVC PIPE - SCHEDULE 40:
MATERIAL/ SPECIFICATION:
Schedule 40 Polyvinyl Chloride, PVC, Pipe shall
meet or exceed the performance specifications of:
• ASTM D1785, dimensional requirements, minimum

burst and sustained pressure requirements,
maximum operating pressure, and test procedures
for determining pipe quality with respect to
workmanship and materials.
• Shall comply with and be labeled as approved by the
National Sanitation Foundation (NSF) for use in
potable water lines meeting NSF 14, 61 or “NSF-pw”.
• ASTM D1784, manufactured from compounds with
Cell Classification 12454B (Type 1, Grade 1
material).
CONNECTIONS:
• Plain end X plain end.
• Plain end X solvent weld bell.
DIMENSIONS:
• 20’ standard joint length.
MANUFACTURER:
• CHARLOTTE PIPE AND FOUNDRY
• COLONIAL
• DIAMOND PLASTICS
• FREEDOM PLASTICS
• NAPCO
• NATIONAL PIPE & PLASTICS
• JM EAGLE
• IPEX
• PIPELIFE
RESTRICTIONS:
Use of this product is limited to:
• Sewer service laterals (DWV)

• 2” Water blow offs
• Water lines

A 2 – PVC PIPE - SCHEDULE 80:
Schedule 80 Polyvinyl Chloride, PVC, Pipe shall meet
or exceed the performance specifications of:
• ASTM D1785, dimensional requirements, minimum

burst and sustained pressure requirements,
maximum operating pressure, and test procedures
for determining pipe quality with respect to
workmanship and materials.
Cell Classification 12454B (Type 1, Grade 1
material).
CONNECTION:
• Plain end X plain end
• Plain end X solvent weld bell
DIMENSIONS:
• 20’ standard joint length
SIZES:
• 3/4”
• 1”
• 1-1/2”
• 2” MANUFACTURER:
• CHEMTROL
• COLONIAL
• ESLON THERMOPLASTICS
• NATIONAL PIPE AND PLASTICS
• WORLD OF PLASTICS, INC.
• JM EAGLE
• IPEX
• NORTH AMERICAN PIPE
• PIPELIFE
RESTRICTIONS:
• Pump station chemical feed applications downstream
from backflow preventer.

A 3 – POLYETHYLENE SERVICE TUBING:
SPECIFICATION/ MATERIAL:
PE-3608 High Density Polyethylene, HDPE, tubing shall
• PE-3608 Resin listed in Plastic Pipe Institute TR4

Cell classification per ASTM Standards D3350 =
345444 or 345464.
• ASTM Standards D2737 dimensional standard,
Copper Tubing Size, CTS, controlled outside
diameter.
• AWWA C901
• MFG. Shall be listed with the Plastic Pipe Institute as
meeting the recipe and mixing requirements for pipe
in this classification.
POTABLE WATER REQUIREMENT:

PRESSURE RATING:
• 200-psi. operating pressure @ 73.4 F
COLOR-CODED:
• Solid blue or blue stripe: potable water
• Solid green or green stripe: sewer
DIMENSIONS:
• Copper tubing size, C.T.S. O.D. controlled
• DR-9
SIZES: MANUFACTURER:
• 1” • DURA-LINE PW TUBING
• 1.5" • ADS
• 2” • CHARTER PLASTICS
• ENDOT
RESTRICTIONS:
• Water service lines 1" or 2"

• LPS service lines 1.5" or 2"

A 3.1 – POLYETHYLENE 2” POTABLE WATER MAIN TUBING:
SPECIFICATION/ MATERIAL:
PE-3608 High Density Polyethylene, HDPE, tubing shall
• PE-3608 Resin listed in Plastic Pipe Institute TR4

Cell classification per ASTM Standards D3350 =
345444 or 345464E.
• ASTM Standards D3035 dimensional standard, Iron
Pipe Size, IPS, controlled outside diameter.
• AWWA C901
potable water lines meeting NSF 14, 61 or “NSFpw”.
PRESSURE RATING:
• 200-psi. operating pressure @ 73.4 F
COLOR-CODED:
• Blue - potable water
• Black with minimum of three (3) evenly spaced blue
stripes - potable water
DIMENSIONS:
• Iron pipe size, I.P.S. O.D. controlled
• DR-9
MANUFACTURER:
• CHARTER PLASTICS/BLUE STRIPE PIPE
SIZES:
• ENDOPURE/ BLUE WITH CLEAR CORE
• 2”
• LAMSON VYLON/ PRESSURE FLEX WATER
• ADS
RESTRICTIONS:
• 2” potable water mains


A 3.2 – HIGH DENSITY POLYETHYLENE PIPE (HDPE) 4”-36”:
MATERIAL/ SPECIFICATION: FIRE MAIN PRESSURE RATING &

PE-4710 High Density Polyethylene, HDPE, pipe shall REQUIREMENTS:
meet or exceed the performance specifications of: • Dimension Ratio (DR) DR-11, pressure class 200
for fire mains.
• PE-4710 Resin listed in Plastic Pipe Institute TR4. • Factory Mutual Approved (FM) pipe.
• Cell classification per ASTM D3350 = 345444C or
345464C for black OR 345444E or 345464E for non-
black & color.
• ASTM F 714, minimum wall values.
• AWWA C906.
POTABLE WATER REQUIREMENTS:

potable water lines meeting NSF 14, 61 or "NSF-pw”.
COLOR– CODED:
• Blue - potable water.
• Green - sanitary sewer/ force main.
DIMENSIONS:
• Ductile iron pipe size O.D., D.I.P.S.
• DR-11, DR-13.5
PRESSURE RATING:
• 200-psi. operating pressure @ 73.4 F for DR-11.
• 160-psi. operating pressure @ 73.4 F for DR-13.5
JOINING RESTRICTIONS: MANUFACTURER:

• Compression type connections are not acceptable in • CHARTER PLASTICS/ STRIPE PIPE
new installations. • CP CHEMICAL
• Pipe joints shall be butt fusion. • PERFORMANCE PIPE DRISCOPLEX
• No electro fusion coupling joints will be accepted. • FLYING W PLASTICS
• Flange or mechanical joint adapters shall be used for • JM EAGLE PE PIPE
pipe and fitting transitions. • LAMSON VYLON/ PRESSURE FLEX WATER
• RINKER MATERIALS– POLY PIPE
• WL PLASTICS
RESTRICTIONS:
• DR-13.5 considered for mains 6” and larger when
hydraulic or availability restrictions apply. Submittal to
and approval by CFPUA required.

A 4 – PVC Pipe (2" and 3” SDR 21):
2" and 3” SDR 21 Polyvinyl Chloride, PVC, Pipe shall
• ASTM D2241 or latest revision thereof.

cell classification 12454B.
• Push-on integral bell type supplied with elastomeric
gaskets installed.
• Joints per ASTM D3139 testing requirements.
• Gaskets per ASTM F477.
• Pipe shall be clean and ends shall be tarped during
shipment.
• Standard Dimension Ratio (SDR) 21.
• No solvent-cement weld pipe or fittings will be
accepted.
PRESSURE RATING:
• 200 psi. at 23 Degrees C (73.4 Degrees F)
COLOR-CODED:
DIMENSIONS:
• Iron pipe size (IPS) Outside diameter controlled
• 20’ and 21’ standard joint length
MANUFACTURER:
• JM EAGLE
• NAPCO
• PIPELIFE
RESTRICTIONS:
Use of this product limited to:
• 2” Water Mains
• 3" Sewer Force Mains

A 5 – PVC PIPE (AWWA C-900) - POTABLE WATER (4” THRU 24”):
MATERIAL/ SPECIFICATION: FIRE MAIN PRESSURE RATING &

AWWA C-900 Polyvinyl Chloride, PVC, Pipe shall meet REQUIREMENTS:
or exceed the performance specifications of: • Dimension Ratio (DR) 14, pressure class 200 for
fire mains.
• ASTM D1784, manufactured from compounds with • Factory Mutual Approved (FM) and Underwriter
cell classification 12454A or 12454B. Laboratory Listed (UL) as noted by (UL/FM)
• Push-on integral bell type joints per ASTM D3139 required on DR 14 pipe.
testing requirements, supplied with elastomeric • No solvent-cement weld pipe or fittings will be
gaskets installed. accepted.
shipment.
accepted.
• Affidavit of compliance to this specification shall be
available upon request.
COLOR– CODED:
DIMENSIONS:
• DR-18, DR-14
PRESSURE RATING:
• 235-psi. operating pressure @ 73 F for DR-18.
MANUFACTURER:
• JM EAGLE/ BLUE BRUTE
• NAPCO
• PIPELIFE
RESTRICTIONS:
• DR-14 is a design option for special installations.
CFPUA approval required.

A 5.1 – PVC PIPE (AWWA C-900) - SEWER (4” THRU 24”):
AWWA C-900 Polyvinyl Chloride, PVC, Pipe shall meet
or exceed the performance specifications of:

cell classification 12454A or 12454B.
• Push-on integral bell type joints per ASTM D3139
testing requirements, supplied with elastomeric
gaskets installed.
• Gaskets per ASTM F477
• Pigment stabilizers and ultraviolet inhibitors shall be
used to prevent fading for a period of six (6) months
after delivery.
shipment.
accepted.
COLOR– CODED:
• Green - sanitary sewer
DIMENSIONS:
• DR-18, DR-14
• Shorter joints acceptable for sewer only
PRESSURE RATING:
• 235-psi. operating pressure @ 73 F for DR-18. MANUFACTURER:
• 305-psi. operating pressure @ 73 F for DR-14. • DIAMOND PLASTICS
• JM EAGLE/ BLUE BRUTE
• NAPCO
• PIPELIFE
RESTRICTIONS:
A 5.2 – PVC PIPE RESTRAINED JOINT PIPE & COUPLINGS (AWWA C-900) Effective Date: 01-01-22
(4” THRU 16”):
AWWA C-900, Pipe shall meet or exceed the
performance specifications of:

cell classification 12454A or 12454B.
potable water lines meeting NSF 14, 61 or “NSF-pw”
for all blue pipe (potable water installation).
• Joined using separate couplings that have built in
sealing gaskets (O-rings) and restraining grooves.
• Shall be joined using high-strength flexible plastic
splines inserted into mating precision-machine
grooves, which align when the pipe is fully inserted,
providing a full 3600 restraint with evenly distributed
loading.
• Joints per ASTM D3139 testing requirements.
shipment.
accepted.
COLOR– CODED:
• Blue– potable water
• Green– sanitary sewer/ force main
DIMENSIONS:
• DR-18, DR-14.
PRESSURE RATING:
MANUFACTURER:
• CERTAINTEED– CERTA-LOK
• JM EAGLE LOC 900
• DIAMOND LOK-21
RESTRICTIONS:
• Only for low profile carrier pipes inside casings with
prior approval by CFPUA.
A 5.3 – PVC PIPE FUSIBLE (AWWA C-900) - POTABLE WATER (4” THRU Effective Date: 01-01-22
24”):
MATERIAL/ SPECIFICATION: PRESSURE RATING:
Fusible AWWA C-900 Polyvinyl Chloride, PVC, Pipe • 235-psi. operating pressure @ 73 F for DR-18.
shall meet or exceed the performance specifications of: • 305-psi. operating pressure @ 73 F for DR-14.

cell classification 12454.
• Manufacture shall be listed with the Plastic Pipe
Institute (PPI) as meeting the recipe and mixing
requirements for pipe in this classification.
• Extruded with a unique formulation, for fusible pipe,
that meets all requirements of PPI TR-2 “PPI PVC
Range Composition Listing of Qualified Ingredients”.
potable water lines meeting NSF 61 or NSF-pw.
shipment.
• Pipe shall be extruded with plain ends. The end shall
be square to the pipe and free of any bevel or
chamfer.
• Fusible pipe shall be joined per the manufacture’s
recommendation.
• Installation shall not exceed manufacture’s bending
radius and safe pulling force.
accepted.
COLOR– CODED:
• Blue - potable water MANUFACTURER:
• UNDERGROUND SOLUTIONS
DIMENSIONS:
• DR-18 DR-14
• 20’, 30’ or 40’ standard joint length.
RESTRICTIONS:
A 5.3.1 – PVC PIPE FUSIBLE (AWWA C-900) - SEWER FORCE MAIN (4” Effective Date: 01-01-22
THRU 24”):
Fusible AWWA C-900 Polyvinyl Chloride, PVC, Pipe
shall meet or exceed the performance specifications of:

cell classification 12454.
• Manufacture shall be listed with the Plastic Pipe
Institute (PPI) as meeting the recipe and mixing
requirements for pipe in this classification.
• Extruded with a unique formulation, for fusible pipe,
that meets all requirements of PPI TR-2 “PPI PVC
Range Composition Listing of Qualified Ingredients”.
shipment.
• Pipe shall be extruded with plain ends. The end shall
be square to the pipe and free of any bevel of
chamfer.
• Fusible pipe shall be joined per the manufacture’s
recommendation.
• Installation shall not exceed manufacture’s bending
radius and safe pulling force.
accepted.
COLOR– CODED:
• Green - sewer force main
DIMENSIONS:
• Ductile iron pipe size O.D., D.I.P.S. MANUFACTURER:
• DR-14, DR-18 • UNDERGROUND SOLUTIONS
• 20’, 30’ or 40’ standard joint length.
PRESSURE RATING:
RESTRICTIONS:

A 6 – DUCTILE IRON PIPE/ PUSH-ON JOINT/ CLASS 350 (3” THRU 36”):
MATERIAL/ SPECIFICATION: COATING & LINING:

• Pipe shall conform with AWWA C151 (ANSIA21.51). Potable Water:
Additionally, pipe exterior shall be coated with a layer • Exterior - AWWA C151 (ANSI-A21.51), per
of arc-sprayed zinc per ISO 8179. The mass of zinc above ISO 8179-1 requirements.
shall be 200 g/m2 of pipe surface area. A finishing • Interior - AWWA C104 (ANSI-A21.4), cement
layer topcoat system shall conform to ISO 8179-1 mortar lining and asphaltic coating.
Ductile iron pipes – External zinc based coating – Sanitary Sewers and Force Mains:
Part 1: Metallic zinc with finishing layer. • Exterior - AWWA C151 (ANSIA21.51) per above
• Gaskets shall be furnished in accordance with ISO 8179-1 requirements.
AWWA C111 (ANSI– A21.11). • Interior - Coated (factory applied) or approved
• Pipe supplied must have ISO 9001 or later equal with an amine cured novolac epoxy,
certification, or poured in a foundry located in the containing at least 20% by volume of ceramic
U.S.A. quartz pigment “PROTECTO 401” or “PERMOX
• Shall comply with and be labeled as approved by the CTF” (40 mils nominal) or polyamine ceramic
National Sanitation Foundation (NSF) for use in epoxy containing at least 20% by volume ceramic
potable water lines meeting NSF 61. hollow microspheres “tnemec series 431
• Factory Mutual Approved (FM) and Underwriter permashield pl” (40 mils nominal).
Laboratory Listed (UL) as noted by (UL/FM) for sizes • The inside of the bell socket including a portion of
four (4”) thru twelve (12”) inch. the gasket cavity and a portion of the pipe barrel
• Affidavit of compliance to this specification shall be are also coated with the above products (6” mils
available upon request. nominal, 10 maximum).
DIMENSIONS:
• 18’ or 20’ standard joint length.
PRESSURE RATING:
• Class 350- psi. for sizes 4” thru 24” pipe.
• Class 250- psi for sizes 30” thru 36” pipe.
MANUFACTURER:
• AMERICAN CAST IRON– FASTITE
• McWANE, INC.– TYTON
• US PIPE & FOUNDRY– TYTON
RESTRICTIONS:
• 3" to be used for sewer force mains only

A 6.1 – DUCTILE IRON PIPE/ FLANGE JOINT/ MINIMUM CLASS 53:

Flange pipe shall meet or exceed the performance Potable Water:
specifications of: • Exterior - AWWA C151 (ANSI-A21.51), per
above ISO 8179-1 requirements.
• Pipe shall conform with AWWA C151 (ANSIA21.51). • Interior - AWWA C104 (ANSI-A21.4), cement
• Flanges shall conform to the chemical and physical mortar lining and asphaltic coating.
properties specified for ductile iron fittings in Sanitary Sewers and Force Mains:
ANSI/AWWA C 110/A21.10. • Exterior - AWWA C151 (ANSIA21.51). per above
• Shall conform to AWWA C115 (ANSI-A21.15) flange ISO 8179-1 requirements.
pipe and fitting joints. • Interior - Coated (factory applied) or approved
• Shall be drilled and faced to conform with ANSI equal with an amine cured novolac epoxy,
B16.1 Class 125 flanges. containing at least 20% by volume of ceramic
quartz pigment “PROTECTO 401” or “PERMOX
GASKETS SHALL BE RING OR FULL-FACE TYPE CTF” (40 mils nominal) or polyamine ceramic
AND PRODUCED FROM ONE OF THE FOLLOWING epoxy containing at least 20% by volume ceramic
MATERIALS: hollow microspheres “TNEMEC SERIES 431
PERMA-SHIELD PL” (40 mils nominal).
• EPDM (Ethylene Propylene Diene Monomer)
• Nitrile Buna-N (NBR) (Acrylonitrile Butadiene)
• Viton; Fluorel (FKM) (Fluorocarbon)
• Pipe supplied must have ISO 9001 or later
certification, or poured in a foundry located in the
U.S.A.
potable water lines meeting NSF 61.
DIMENSIONS:
• 18’ or 20’ standard joint length or as specified for
project.
PRESSURE RATING:
• Class 250-psi. for sizes 4” thru 24” pipe.
MANUFACTURER:
• AMERICAN CAST IRON
• McWANE, INC.
• US PIPE & FOUNDRY
RESTRICTIONS:
• Flange pipe is for use in inside buildings, above
ground outside, or inside underground vault or
manhole service applications.
• All flanged piping inside vaults must be zinc
coated to match CFPUA requirement for direct
bury.
A 6.2 – DUCTILE IRON PIPE/ RESTRAINED PUSH-ON JOINT/TR FLEX Effective Date: 01-01-22
JOINT (3” THRU 36”):
Restrained pipe shall meet or exceed the performance Potable Water:
specifications of: • Exterior - AWWA C151 (ANSI-A21.51) per above
ISO 8179- 1 requirements.
• Shall conform with AWWA C150 (ANSI– A21.50) • Interior - AWWA C104 (ANSI-A21.4), cement
thicknesses and strength. mortar lining and asphaltic coating.
• Shall conform with AWWA C151 (ANSI-A21.51), Sanitary Sewers and Force Mains:
Additionally, pipe exterior shall be coated with a layer • Exterior - AWWA C151 (ANSIA21.51) per above
of arc-sprayed zinc per ISO 8179. The mass of zinc ISO 8179-1 requirements.
shall be 200 g/m2 of pipe surface area. A finishing • Interior - Coated (factory applied) or approved
layer topcoat shall be applied to the zinc. The zinc equal with an amine cured novolac epoxy,
coating system shall conform to ISO 8179-1 “Ductile containing at least 20% by volume of ceramic
iron pipe – External zinc based coating – Part 1: quartz pigment “PROTECTO 401” or “PERMOX
Metallic zinc with finishing layer. CTF” (40 mils nominal) or polyamine ceramic
• Gaskets shall be furnished in accordance with epoxy containing at least 20% by volume ceramic
AWWA C111 (ANSI– A21.11). hollow microspheres “TNEMEC SERIES 431
• Shall use a standard size Tyton gasket. PERMA-SHIELD PL” (40 mils nominal).
• Shall use ductile iron locking segments, inserted
through a slot (or slots) in the bell face, to provide a
positive axial lock between the bell interior surface
and a retainer weldment on the spigot end of the
pipe.
U.S.A.
• Factory Mutual Approved (FM) and Underwriter
Laboratory Listed (UL) as noted by (UL/FM) for sizes
four (4”) thru twelve (12”) inch.
PRESSURE RATING:
DIMENSIONS:
MANUFACTURER:
• US PIPE & FOUNDRY– TR FLEX
• McWANE, INC.– TR FLEX
RESTRICTIONS:
A 6.3 – DUCTILE IRON PIPE/ RESTRAINED PUSH-ON JOINT/FLEX– RING Effective Date: 01-01-22
JOINT (3” THRU 48”):
Restrained pipe shall meet or exceed the performance Potable Water:
specifications of: • Exterior - AWWA C151 (ANSI-A21.51) per above
ISO 8179-1 requirements.
• Shall conform with AWWA C150 (ANSI– A21.50) • Interior - AWWA C104 (ANSI-A21.4), cement
thicknesses and strength. mortar lining and asphaltic coating.
• Shall conform with AWWA C151 (ANSI-A21.51), Sanitary Sewers and Force Mains:
Additionally, pipe exterior shall be coated with a layer • Exterior - AWWA C151 (ANSIA21.51) per above
of arc-sprayed zinc per ISO 8179. The mass of zinc ISO 8179-1 requirements.
shall be 200 g/m2 of pipe surface area. A finishing • Interior - Coated (factory applied) or approved
layer topcoat shall be applied to the zinc. The zinc equal with an amine cured novolac epoxy,
coating system shall conform to ISO 8179-1- Ductile containing at least 20% by volume of ceramic
iron pipe – External zinc based coating – Part 1: quartz pigment “PROTECTO 401” or “PERMOX
Metallic zinc with finishing layer. CTF” (40 mils nominal) or polyamine ceramic
• Gaskets shall be furnished in accordance with epoxy containing at least 20% by volume ceramic
AWWA C111 (ANSI-A21.11). hollow microspheres “TNEMEC SERIES 431
• Shall use a standard size Fastite gasket. PERMA-SHIELD PL” (40 mils nominal).
U.S.A.
• Factory Mutual Approved (FM) and Underwriter
Laboratory Listed (UL) as noted by (UL/FM) for sizes
four (4”) thru twelve (12”) inch.
PRESSURE RATING:
• Class 350-psi. for sizes 4” thru 24” pipe. MANUFACTURER:
• Class 250-psi. for sizes 30” thru 36” pipe. • AMERICAN CAST IRON– FLEX-RING
DIMENSIONS:
ADDITIONAL INFORMATION:
• Standard Flex-Ring segments are yellow.
• Field Flex-Ring segments are black.
RESTRICTIONS:

A 7 – STAINLESS STEEL PIPE:
• Schedule 40, 316 stainless steel pipe.
• Specifications shall conform to ANSI/ASME 36.19.
CONNECTIONS:
• Pipe shall have NPT threads on both ends and a
coupling on one end making a full joint, mipt X fipt. As
required on detail drawings.
DIMENSIONS:
MANUFACTURER:
• OPEN
RESTRICTIONS:
• This material is required for air/vacuum release valve
piping or other special uses as noted on detail
drawings.

A 8 – GALVANIZED PIPE (TEMPORARY):
• Schedule 40, galvanized steel pipe.
• Specifications shall conform to ASTM A-53 grade-A
or latest revision thereof.
CONNECTIONS:
• Pipe shall have NPT threads on both ends and a
coupling on one end making a full joint, mipt X fipt.
DIMENSIONS:
MANUFACTURER:
• OPEN
RESTRICTIONS:
• This material is only used for temporary sampling and
flushing points during pipeline construction.
• Galvanized pipe is not acceptable for any other use.

Section A Pipe

Uploaded by

Copyright:

Available Formats

Section A Pipe

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Section A Pipe

Uploaded by

Copyright:

Available Formats

Material Specification Manual Section A: Pipe

Effective Date: 01-01-23

A1 PVC Pipe - Schedule 40

A2 PVC Pipe - Schedule 80

A3 Polyethylene Service Tubing

A 3.1 Polyethylene 2” Potable Water Main Tubing

A 3.2 High Density Polyethylene Pipe (HDPE)

A4 PVC Pipe (2" & 3” SDR-21)

A5 PVC Pipe (AWWA C – 900) – Potable Water (4” thru 24”)

A 5.1 PVC Pipe (AWWA C – 900) – Sewer (4” thru 24”)

A 6.1 Ductile Iron Pipe/ Flanged Joint/ Class 53

A7 Stainless Steel Pipe

A8 Galvanized Pipe (Temporary)

Effective Date: 01-01-22

• ASTM D1785, dimensional requirements, minimum

• Sewer service laterals (DWV)

Effective Date: 01-01-22

• ASTM D1785, dimensional requirements, minimum

Effective Date: 01-01-22

• PE-3608 Resin listed in Plastic Pipe Institute TR4

POTABLE WATER REQUIREMENT:

• Water service lines 1" or 2"

Effective Date: 01-01-22

• PE-3608 Resin listed in Plastic Pipe Institute TR4

• 2” potable water mains

Effective Date: 01-01-22

MATERIAL/ SPECIFICATION: FIRE MAIN PRESSURE RATING &

POTABLE WATER REQUIREMENTS:

JOINING RESTRICTIONS: MANUFACTURER:

Effective Date: 01-01-22

• ASTM D2241 or latest revision thereof.

Effective Date: 01-01-22

MATERIAL/ SPECIFICATION: FIRE MAIN PRESSURE RATING &

Effective Date: 01-01-22

• ASTM D1784, manufactured from compounds with

• ASTM D1784, manufactured from compounds with

• ASTM D1784, manufactured from compounds with

• ASTM D1784, manufactured from compounds with

Effective Date: 01-01-22

MATERIAL/ SPECIFICATION: COATING & LINING:

Effective Date: 01-01-22

MATERIAL/ SPECIFICATION: COATING & LINING:

Effective Date: 01-01-22

Effective Date: 01-01-22

You might also like