DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

F. PIMENTEL AVE. PASIG, DAET, CAMARINES NORTE REGION V

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 TABLE OF CONTENTS

W E

LOCATION MAP
SCALE NTS
N

W E 1 2 3 4 5 6 7 8 9
36.00
0.60 9.00 9.00 9.00 4.50 0.60
4.50 4.50 4.50 4.50 4.50 4.50 4.50

SITE DEVELOPMENT PLAN

SCALE NTS

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 1 2 3 4 5 6 7 8 9
36.00
4.50 9.00 9.00 9.00 4.50
0.425 0.96 1.20 4.50 4.50 4.50 4.50 4.50 4.50 1.825 1.40 1.275

X 0.955 0.96
W-3
0.425

A W-1 W-1 W-1 W-1 W-1 W-1

1.40
3.15
1.75
D-2
D-3 D-3

7.00
9.50

3.85
D-1 W-2 W-2 D-1 D-1 W-2 W-2 D-1 D-1 W-2 W-2 D-1

B 25mm DEP. 25mm DEP. 25mm DEP. 25mm DEP. 25mm DEP. 25mm DEP.

2.50

2.50
C

SECOND FLOOR PLAN

SCALE 1:100mts
Y

1 2 3 4 5 6 7 8 9
36.00
4.50 9.00 9.00 9.00 4.50
0.85 1.825 4.50 4.50 4.50 4.50 4.50 4.50 1.825 1.40 1.275

X 0.975 0.85
W-4 W-3
0.425

1.00
W-1 W-1 W-1 W-1 W-1 W-1
1.40

2.00
SCHEDULE OF WALL FINISHES
1.75

D-2 D-2
150mm THK. CHB w/ PLAIN CEMENT
D-3 D-3 WF1 PLASTER (PAINT FINISH)
100mm THK. CHB PLAIN CEMENT
7.00

7.00
WF2 RAILINGS ( PAINT FINISH)
150mm THK. CHB w/ 200 x 200mm VITRIFIED
WF3 WALL TILES (GLAZED)
9.50

100mm THK. CHB w/ 200 x 200mm VITRIFIED

4.00
3.85

WF4 WALL TILES (GLAZED)

D-1 W-2 W-2 D-1 D-1 W-2 W-2 D-1 D-1 W-2 W-2 D-1 SCHEDULE OF FLOOR FINISHES
B D-5
25mm DEP. 25mm DEP. 25mm DEP. 25mm DEP. 25mm DEP. 25mm DEP.
D-5
FF1 NON SKID PLAIN CEMENT FLOOR FINISH
NON SKID PLAIN CEMENT FLOOR FINISH
2.50

2.50
FF2 ROUGH FINISH w/ GROOVES

FF3 200 x 200 VITRIFIED FLOOR TILES (UNGLAZED)

C
RAMP UP

RAMP UP
GROUND FLOOR PLAN
Y
SCALE 1:100mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 0.60mm THK. (BASE METAL THICKNESS)
PRE-PAINTED ORDINARY RIDGE ROLL

1 2 3 4 5 6 7 8 9
36.00 0.40mm THK. PRE-PAINTED LONG SPAN
CORRUGATED G.I. ROOFING SHEET
0.60 4.50 4.50 4.50 4.50 4.50 4.50 4.50 4.50 0.60

ANGULAR BAR 40 x 40 x 5 x
500mm ON EVERY PURLINS

2.50
0.60 THK. (BASE METAL THICKNESS)
PREFORMED, PRE-PAINTED G.I
FLASHING SHEET w/ 12 x 300mM FIBER
CEMENT FASCIA BOARD (PAINT FINISH)

3.20
D-2 D-2

D-1 W-2 W-2 D-1 D-1 W-2 W-2 D-1 D-1 W-2 W-2 D-1 100mm CHB RAILING.
(TYPICAL) w/ PAINTED FINISH

12.43
3.20
D-2 D-2
50mm G.I PIPE HANDRAIL
(PAINT FINISH), TYPICAL

D-1 W-2 W-2 D-1 D-1 W-2 W-2 D-1 D-1 W-2 W-2 D-1
3.20

D-3 D-2 D-2 D-3

38mm G.I PIPE HANDRAIL w/
38mm VERT SUPPORT @
D-1 W-2 W-2 D-1 D-1 W-2 W-2 D-1 D-1 W-2 W-2 D-1 600mm O.C. (PAINT FINISH)
0.325

PWD RAMP (SEE DETAIL)

FRONT ELEVATION
SCALE 1:100mts

1 2 3 4 5 6 7 8 9
36.00
4.50 9.00 9.00 9.00 4.50
0.425 0.96 1.20 4.50 4.50 4.50 4.50 4.50 4.50 1.825 1.40 1.275

X 0.955 0.96
W-3
0.425

A W-1 W-1 W-1 W-1 W-1 W-1

1.40

1.40
3.15
1.75

1.75
D-2
D-3 D-3
7.00
9.50

3.85

3.85
D-1 W-2 W-2 D-1 D-1 W-2 W-2 D-1 D-1 W-2 W-2 D-1

B 25mm DEP. 25mm DEP. 25mm DEP. 25mm DEP. 25mm DEP. 25mm DEP.
2.50

2.50
C

THIRD FLOOR PLAN

SCALE 1:100mts
Y

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 3 2 1 1 2 3 1 2 3
9.50 9.50 9.50
1.50 2.50 7.00 1.50 1.50 7.00 2.50 1.50 1.50 7.00 2.50 1.50
0.60mm THK. (BASE METAL THICKNESS)
PRE-PAINTED PRE-FROMED RIDGE ROLL
0.40mm THK. PRE-PAINTED LONG SPAN 4.50mm THK. FIBER CEMENT
CORRUGATED G.I ROOFING SHEET CEILING BOARD (PAINTED)
2.50

2.50
ON METAL FURRING
CHANNEL @ 400mm O.C.

0.50
0.60mm THK. (BASE METAL THICKNESS)
3.20

3.20
PRE-FORMED, PRE-PAINTED G.I GUTTER w/ 12 x

2.70
300mm FIBER CEMENT FASCIA BOARD (PAINT FINISH)

0.90

1.10
12.43

12.43
EXPOSED CEILING UNDER
150mm. THK. CHB WALL WITH PAINTED PLAIN
3.20

3.20
SLAB (PAINT FINISH)
CEMENT PLASTER WALL FIN ISH

1.10
SEE SUNBREAKER DETAILS
150mm THK. CHB WALL w/
PAINTED PLAIN CEMENT
3.20

3.20
1.40 PLASTER WALL FINISH

100mm THK. CHB RAILING w/ 50mm G.I PIPE

HANDRAIL (PAINT FINISH)
0.325

0.325
RIGHT SIDE ELEVATION LEFT SIDE ELEVATION SECTION THRU "X"
SCALE 1:100mts SCALE 1:100mts SCALE 1:100mts

9 8 7 6 5 4 3 2 1
36.20 0.60mm THK. (BASE METAL THICKNESS)
PRE-PAINTED ORDINARY RIDGE ROLL
4.70 4.50 4.50 4.50 4.50 4.50 4.50 4.50
0.40mm THK. PRE-PAINTED LONG SPAN
CORRUGATED G.I. ROOFING SHEET

ANGULAR BAR 40 x 40 x 5 x
500mm ON EVERY PURLINS
2.50

0.60 THK. (BASE METAL THICKNESS)

PREFORMED, PRE-PAINTED G.I
FLASHING SHEET w/ 12 x 300mM FIBER
CEMENT FASCIA BOARD (PAINT FINISH)
3.20

W-3 W-4 W-3

PLAIN CEMENT PLASTER
W-1 W-1 W-1 W-1 W-1 W-1
(PAINT FINISH)
12.43
3.20

CONCRETE SUNBREAKER
W-3 W-4 W-3
(SEE DETAILS)
W-1 W-1 W-1 W-1 W-1 W-1
3.20

W-3 W-4 W-4 W-3

W-1 W-1 W-1 W-1 W-1 W-1

0.325

REAR ELEVATION
SCALE 1:100mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 4.50mm THK. FIBER CEMENT CEILING BOARD (PAINTED)
ON METAL FURRING CHANNEL @ 400mm O.C.

1 2 3 4 5 6 7 8 9
36.00
4.50 4.50 4.50 4.50 4.50 4.50 4.50 4.50
SECOND FLOOR LEVEL
2.50
3.20

W-1 W-1 W-1 W-1 W-1 W-1

W-2 D-1
12.43
3.20

0.05
0.05 0.663
W-1 W-1 W-1 W-1 W-1 W-1

SPOT DETAIL "2" ELEVATION

SCALE 1:50mts
3.20

W-1 W-1 W-1 W-1 W-1 W-1

0.325

200 x 200mm VITRIFIED SECOND FLOOR LEVEL

WALL TILES (GLAZED) FINISH
SECTION THRU "Y"
SCALE 1:100mts

EXPOSED UNDERSIDE OF CONCRETE

SLAB (WITH PAINT FINISH) TYPICAL

1 2 3 4 5 6 7 8 9 W-2 D-1 D-1 W-2

36.00
4.50 9.00 9.00 9.00 4.50
4.50 4.50 4.50 4.50 4.50 4.50
0.05 0.05 0.663 0.663

A 0.575

CL-2 CL-2 CL-2 CL-2 SPOT DETAIL "1" ELEVATION

SCALE 1:50mts
7.00
9.50

W-2 D-1 D-1 W-2 W-2 D-1

B 25mm DEP. 25mm DEP. 25mm DEP.

2.50

C
GROUND FLOOR REFLECTED CEILING PLAN SPOT DETAIL PLAN 1 & 2
SCALE 1:100mts SCALE 1:50mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 VARIES
(420 MAX)
50 x 50mm TOP HOR. 0.42
0.025
FRAME (CURVED) 0.05 0.05
FR. 50 x 50mm TOP HOR.
S4S KD. TANG. HOR.
FRAME @ 600mm O.C.
1 2 3 4 5 6 7 8 9

0.05
4 EQUAL SPACE
6mm THK LAWANIT BD.

0.60
36.00 150mm THK CHB WALL 25 x 50mm

1.20
4.50 9.00 9.00 9.00 4.50 EDGE FRAMING 10mm M. BOLT
4.50 4.50 4.50 4.50 4.50 4.50 FR. 50 x 50mm VERT.
STUD @ 450mm O.C. BLACKBOARD W5200
50 x 50mm BOTT. HOR.
FRAME ( CURVED)

0.12
SPOT DETAIL SECTION HARD WOOD 50x100

EDGE FRAMING
SECTION SCALE 1:15mts HARDWOOD 50x50

1.20
SCALE 1:20mts VERT. STUD @ 450 O.C.
7.00
9.50

ELEMENTARY H650
SECONDARY H750
6mm THK 6mm THK

0.12
PLYWOOD PLYWOOD
2.50

10 x 10 x 2mm CLSRM. FIN. FLR. LINE

MESHWIRE
C

0.60mm THK. (BASE METAL THICKNESS) 120 x 150 x 70mm

THIRD FLOOR REFLECTED CEILING PLAN PRE-FORMED, PRE-PAINTED G.I GUTTER w/ 12 x

300mm FIBER CEMENT FASCIA BOARD (PAINT FINISH)
CHALKDUST BOX CONN. SECTION DETAIL
SCALE 1:20mts
SCALE 1:100mts
25 x 25 x 300mm WOOD SLATS @ 25mm
CHALK DUST BOX DETAIL
SCALE 1:15mts
CLEAR SPACING CEILING VENTILATION 6mm THK. LAWANIT
(PROVIDE WIRE MESH INSIDE) TYPICAL COVER BOTH SIDE WITH 6mm THK
25 x 50mm FRAMING BOARD ORDINARY PLYWOOD
4.07
2.03 2.03

0.04
EXPOSED UNDERSIDE OF CONCRETE
SLAB (WITH PAINT FINISH) TYPICAL

1 2 3 4 5 6 7 8 9

1.00
36.00
5
4.50 9.00 9.00 9.00 4.50 A-5
4.50 4.50 4.50 4.50 4.50 4.50

0.04

0.06
A 25 x 50mm TANGUILE
FRONT VIEW
JOINT
0.25

CL-2 CL-2
4.07
2.03 2.03
LINE OF 150mm THK.
CHB WALL
50 x 50 VERTICAL

0.08
7.00

STUD @ 450mm O.C.

9.50

50 x 50 HORIZONTAL

0.35
FRAME @ 600mm O.C.

PLAN VIEW B
SECTION LAWANIT BOARD

B 2.03
4.07
2.03
LINE OF 150mm THK. CHB WALL
2.50

LAWANIT BOARD

0.35
5
A-6

PLAN VIEW A
SECOND FLOOR REFLECTED CEILING PLAN
SCALE 1:100mts BLACKBOARD DETAIL
SCALE 1:25mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 2.50 1.50
CHB t=150
2-4" CWN SPACE @ EVERY 200mm
SILICON OR POLYSULFIDE SEALANT
SIM PLYWOOD t=10mm 100mm @ 0.40mm THK. (BASE METAL 0.40mm THK. (BASE METAL
300mm (SUS 70) THICKNESS) LONG SPAN THICKNESS) LONG SPAN
50x150mm WOOD
JAMB PRE-PAINTED G.I ROOFING SHEET PRE-PAINTED G.I ROOFING
LOOSE PIN HINGES WITH TOTAL COATED THICKNESS OF SHEET WITH TOTAL COATED
0.50mm THK. THICKNESS OF 0.50mm THK.

2.50

2.50
PANEL DOOR
FIX GLASS 4.50mm THK. FIBER CEMENT
CORRIDOR 4.50mm THK. FIBER CEMENT CEILING CEILING BOARD (PAINTED) ON
BOARD (PAINTED) ON METAL FURRING METAL FURRING CHANNEL @
CHANNEL @ 400mm O.C. 400mm O.C.
50x150mm

0.15
WOODEN JAMB
GLASS BLADES 0.60mm THK. (BASE METAL 0.60mm THK. (BASE METAL
(CLEAR t=6.00mm) W-3 THICKNESS) PRE-FORMED, THICKNESS) PRE-FORMED,

0.20
D-3 PRE-PAINTED G.I GUTTER w/ 12

3.20

3.20
PRE-PAINTED G.I GUTTER w/ 12 x
CLASSROOM JALOPLUS x 300mm FIBER CEMENT 300mm FIBER CEMENT FASCIA
FRAME FASCIA BOARD (PAINT FINISH) BOARD (PAINT FINISH)

0.90
.077

1.50
CHB t=150
SILICON OR POLYSULFIDE SEALANT 150mm THK. CHB WALL WITH
W-3 PAINTED PLAIN CEMENT
38x60mm JALOPLUS FRAME 100mm THK. CHB RAILING WITH

9.60

9.60
D-3

3.20

3.20
PLASTER WALL FINISH
METAL SCREW w/ TONG @300mm OC CLASSROOM 50mm G.I PIPE HANDRAIL
(PAINT FINISH)
ROTOR JALOPLUS FRAME

GLASS BLADES CORRIDOR

GLASS BLADES
(CLEAR t=6.00mm) 200 x 200mm VITRIFIED WALL EXPOSE CEILING UNDER
W-3 TILES (GLAZED) SLAB PAINT FINISH
D-3

3.20

3.20
150mm THK. CHB WALL WITH
50 x 150mm PAINTED PLAIN CEMENT
CLASSROOM WOODEN JAMB
PLASTER WALL FINISH
CHB t=150

GLASS JALOUSIE DETAILED PLANS

0.325

0.325
SCALE 1:5mts

CORRIDOR .10

GLASS JALOUSIE DETAILED SECTION BAY SECTION (ALONG TOILET) BAY SECTION (ALONG CORRIDOR)
SCALE 1:5mts SCALE 1:75mts SCALE 1:75mts

1 2 3 4 5 6 7 8 9
36.00
0.60 9.00 9.00 9.00 4.50 0.60
4.50 4.50 4.50 4.50 4.50 4.50 4.50

CHB t=150
2-4" CWN SPACE
1.50

@ EVERY 200mm
A SILICON OR POLYSULFIDE
SEALANT WITH SIM
PLYWOOD t=10mm
0.60mm THK. (BASE METAL THICKNESS)
50 x 150mm
PRE-PAINTED ORDINARY RIDGE ROLL
6.25

WOOD JAMB
0.40mm THK. ( BASE METAL THICKNESS) PANEL DOOR
PRE-PAINTED LONG SPAN G.I. ROOFING
SHEET w/ TOTAL COATED THICKNESS OF
7.00

0.50mm THICK.

CLASSROOM
0.60 THK. (BASE METAL THICKNESS)
PREFORMED, PRE-PAINTED G.I
FLASHING SHEET w/ 12 x 300mm FIBER
CEMENT FASCIA BOARD (PAINT FINISH)
B
6.25

CORRIDOR
2.50

ANGULAR BAR 40 x 40 x 5 x

.025
0.11
500mm ON EVERY PURLINS

C
1.50

0.60mm THK. (BASE METAL THICKNESS)

PRE-FORMED, PRE-PAINTED G.I GUTTER w/ 12 x
DOOR FRAME TYPICAL SECTION DETAIL
SCALE 1:5mts
300mm FIBER CEMENT FASCIA BOARD (PAINT FINISH)

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 2 - 38mm G.I PIPE HANDRAIL (PAINTED FINISH)
FULL WELDED ON 38mm G.I PIPE RAILINGS
2 - 38mm G.I PIPE HANDRAIL NON-SKID PLAIN CEMENT 0.10
(VERT. SUPPORT @ 600mm O.C (PAINTED)

0.20
w/ 38mm VERTICAL SUPPORT FLOOR FINISH w/ GROOVE LINE 0.10
0.10

0.20
@ 1200mm O.C (PAINT FINISH)
0.30
0.30
0.70 0.20

0.90

0.70 0.20
0.70

0.90
1.20

0.70

0.10
0.90

0.006
0.90
0.10

0.10
0.30

0.30
0.10 3.60 1.70
100mm THK. NON-SKID PLAIN CEMENT
5.30 GRAVEL BEDDING FLOOR FINISH
0.10 3.60 1.70 6mm GROOVE LINE

DETAILS OF RAMP DETAILED SECTION OF RAMP

SCALE 1:30mts SCALE 1:30mts

4 EQUAL PARTS = 2.50

SPOT DETAILS
1.40 0.60 SCALE 1:30mts

7 - BLADES
0.30

0.30
F F F F F F

0.635
4.70
14 - BLADES

14 - BLADES

0.30
2.40

2.40

2.40

1.765

1.20
0.90

0.90
0.30 3.60 1.70
W-1 W-2 W-3
JALOUSIE WINDOWS WITH CLEAR GLASS JALOUSIE WINDOWS WITH CLEAR GLASS JALOUSIE WINDOWS WITH CLEAR GLASS
BLADES ON STANDARD JALOUPLUS CASING BLADES ON STANDARD JALOUPLUS CASING BLADES ON STANDARD JALOUPLUS CASING
ON 50 x 150mm MAHOGANY JAMB COMPLETE
DETAILED PLAN OF RAMP
AND FIXED CLEAR GLASS TRANSOM ON 50 x AND FIXED CLEAR GLASS TRANSOM ON 50 x SCALE 1:40mts
150mm MAHOGANY JAMB COMPLETE WITH 150mm MAHOGANY JAMB COMPLETE WITH WITH HARDWARE AND ACCESSORIES
HARDWARE AND ACCESSORIES HARDWARE AND ACCESSORIES
9 SETS
12 SETS 12 SETS
0.90

0.90 0.80 0.70

0.30

0.60

0.10
2.40
2.10

2.10

2.10

2.10

0.20
2 2 38mm G.I PIPE

1.20
1.50 HANDRAIL w/ 38mm
VERTICAL SUPPORT @
100 x 100mm
600mm O.C. (PAINT FINISH)
CONCRETE SKIRTING

0.90
0.30

38mm G.I PIPE VERT. SUPPORT @

0.30

600mm O.C. PROVIDE 12mm

0.70
STEEL DOWEL (PAINTED FINISH)
12mm STEEL DOWEL
0.80
EMBED ON CONCRETE

D-1 D-2 D-3 D-4 D-5 NON-SKID PLAIN CEMENT

0.10
FLOOR FINISH w/ GROOVE

0.15
LINES
MAHOGANY PANEL DOOR ON 50 x 150mm HOLLOW CORE FLUSH TYPE SWING DOOR HOLLOW CORE FLUSH TYPE SWING SWING DOOR ON 50 x 150mm
T HK. MA HOG A NY J A M B F IX ED C LEA R ON 50 x 150mm MAHOGANY JAMB w/ MARINE DOOR ON 50 x 150mm MAHOGANY JAMB MAHOGANY DOOR JAMB COMPLETE w/ HO LLOW CORE FLUSH DOO R
GLASS TRANSOM COMPLETE WITH PLYWOOD FACING INSIDE AND ONDINARY w/ MARINE PLYWOOD FACING INSIDE HARDWARE AND ACCESSORIES WITH MARINE PLYWOOD FACING
HARDWARE AND ACCESSORIES OUTSIDE COMPLETE w/ HARDWARE AND AND ONDINARY OUTSIDE COMPLETE w/
C Y L I N D E R T Y P E L O C K S E T ACCESSORIES PROVIDE KICK PLATE HARDWARE AND ACCESSORIES 8 SETS 1 SETS

12 SETS 1 SETS 6 SETS

SCHEDULE OF DOORS AND WINDOWS SPOT DETAILS DETAILED SECTION

SCALE 1:30mts SCALE 1:5mts SCALE 1:15mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 0.50 0.025

0.025
0.05 0.05

0.05
3.20

0.90
0.10

0.168
0.175
1.52

0.90

SPOT DETAIL NOSING DETAIL

SCALE 1:5mts SCALE 1:3mts
SECTION DETAILS
9.60
3.20

SCALE 1:15mts

0.20
1.68

0.05

1.35

0.29
1.52

0.90

0.15 0.15 0.15 0.15 0.15

0.05
3.20

0.39
1.71

TYPICAL
0.85
0.30

DETAILED SECTION OF STAIR SPOT DETAIL

SCALE 1:50mts SCALE 1:15mts

2.95 2.95 2.95

1.35 0.20 1.40 1.35 0.20 1.40 1.35 0.20 1.40

SECTION DETAIL
SCALE 1:15mts 0.05 0.05
0.30
1.35

10 10 29

11 9 11 9 30 28

0.20
12 8 12 8 31 27
4.05

13 7 13 7 32 26

0
14 6 14 6 33 25

.16
5
2.70

0.90
15 5 15 5 34 24

0.05
16 4 16 23 35 23

3 17 22 36 22

2 18 21 37 21

D-3 1 19 20 38 20

UP DN UP DN
1.50

( AT GROUND FLOOR ) ( AT SECOND FLOOR ) ( AT THIRD FLOOR )

DETAILED PLAN OF STAIRS DETAILED PLAN OF STAIRS DETAILED PLAN OF STAIRS HANDRAIL DETAIL BALCONY RAILING DETAILS
SCALE 1:40mts SCALE 1:40mts SCALE 1:40mts SCALE 1:5mts SCALE 1:25mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 ROD SUSPENSION HANGER METAL DOUBLE FURRING CHANNEL ( NAILER )
WITH ADJUSTMENT SPRING 12mm x 38mm x 5m x 0.8mm THK, AT 400mm O.C. 25 X 25mm WOOD SLAT
PROVIDE INSECT SCREEN
1 2
4.50mm THK. FIBER CEMENT
0.25 0.25 CEILING BOARD (PAINTED)
0.012 0.012
0.325 ON METAL FURRING

0.10
CHA NNEL @ 400mm O.C.

0.40

0.40
METAL CARRYING CHANNEL (CEILING JOIST )

DEPTH OF CEILING TO REQUIRED DIMENSION

12mm x 38mm x 5m x 0.8mm THK, AT 1200mm O.C.
FIBER CEMENT CEILING RB - 2 FR. 25 x 75mm VENT
BOARD 4.5mm THK. FRAME (PAINT FINISH)

0.025 0.30 0.025

ROD SUSPENSION
H A N G E R W I T H SECTION "B"
PREFORMED
ADJUSTMENT SPRING SCALE 1:10mts
TYP. CEILING VENT SECTION DETAIL
WIRE CLIP SCALE 1:5mts

0.40mm WALL ANGLE

0.40mm THK. (BASE METAL THICKNESS)

0.475 LONG SPAN PRE-PAINTED G.I ROOFING
SHEET WITH TOTAL COATED
THICKNESS OF 0.50mm THK.
1.175

0.30
0.10 0.10
PRIMARY
CHANNEL

12 x 12mm DRIP MOLD

0.625
TYP. CEILING VENT PLAN DETAIL
SCALE 1:10mts

CEILING FURRING
FIBER CEMENT CEILING SECTION
BOARD

PERSPECTIVE (CEILING)
SCALE NTS
SECTION THRU "X" SEE TRUSS DETAILS
SCALE 1:10mts

1.10 0.40mm THK. (BASE METAL

THICKNESS) LONG SPAN PRE-PAINTED
TOP CHORD SEE STRUCTURAL DETAIL G.I ROOFING SHEET WITH TOTAL 4.50mm THK. FIBER CEMENT CEILING
COATED THICKNESS OF 0.50mm THK. BOARD (PAINTED) ON METAL
C - PURLINS SEE STRUCTURAL DETAIL FURRING CHANNEL @ 400mm O.C.
4.50mm THK. FIBER CEMENT CEILING
SAGROD SEE STRUCTURAL DETAIL BOARD (PAINTED) ON METAL
FURRING CHANNEL @ 400mm O.C.
0.60mm THK. (BASE METAL THICKNESS)
PRE-FORMED, PRE-PAINTED G.I GUTTER
w/ 12mm x 300mm FIBER CEMENT 0.60mm THK. (BASE METAL THICKNESS)
FASCIA BOARD (PAINT FINISH) PRE-FORMED, PRE-PAINTED G.I GUTTER
w/ 12 x 300mm FIBER CEMENT FASCIA
0.40

B O A R D ( P A I N T F I N I S H )
BASKET STRAINER
2- 65mm x 65mm BAR
0.10

BASKET STRAINER
4.5mm THK. FIBER CEMENT CEILING
BOARD ( PAINTED ) ON METAL FURRING 75mm PVC DOWNSPOUT
75mm PVC DOWNSPOUT
CHANNEL @ 400mm O.C. ( P A I N T F I N I S H )
( P A I N T F I N I S H )

SECTION DETAIL (EAVES) SECTION DETAIL (EAVES) SECTION DETAIL (CORNER CLG)
SCALE 1:20mts SCALE 1:10mts SCALE 1:10mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 1 2 1 2

0.20
4.50 4.50
0.425 0.550.85 0.85 1.825 1.825 1.40 0.85 0.425

0.60
0.25 0.15

1.40

2.00
0.60

3.15

3.15
0.10

1.75

1.15
0.10 0.60 0.10
1.10 0.80
1.60

1.60

0.50 0.30
0.15 DETAILED PLAN OF TOILET @ 2ND & 3RD FLOOR
0.07

0.07
0.25 0.20
0.80

0.80
0.25 SCALE 1:50mts
0.30
0.25

1 2 1 2

0.15

0.15
4.50 4.50
0.425 0.550.85 0.85 1.825 1.825 1.40 0.85 0.425

0.60
0.54

1.40
DETAILED SECTION OF COUNTER SINK

2.00
SCALE 1:50mts

3.15

3.15
URINAL TROUGH SECTION & DETAILS

1.75
SCALE 1:20mts

1.15
4.50 4.50
1.380 0.96 0.96 1.20 2.00 1.10 1.400
0.425 0.425
DETAILED PLAN OF TOILET @ GROUND FLOOR
SCALE 1:50mts
0.50

0.50

0.50
3.20

3.20
2.70
1.60

1.60

1.60
0.50

0.50

0.50
3.20

3.20
1.60

1.60

1.60
0.50

0.50

0.50
3.20

3.20
1.60

1.60

1.60
0.90
0.325

0.325

DETAILED SECTION OF FEMALE TOILETS DETAILED SECTION OF MALE TOILETS DETAILED SECTION OF FEMALE TOILETS DETAILED SECTION OF MALE TOILETS
SCALE 1:50mts SCALE 1:50mts SCALE 1:50mts SCALE 1:50mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
1. IN THE INTERPRETATION OF THE DRAWING, INDICATED DIMENSIONS SHALL GOVERN 1. UNLESS OTHERWISE NOTED IN PLANS, THE STRENGTH OF REINFORCING BARS SHALL BE: 1. PROVIDE EXTRA SETS OF TIES AT 100mm OC FOR TIED COLUMN REINFORCEMENT ABOVE AND
AND DISTANCES AND SIZES SHALL NOT BE SCALED FOR CONSTRUCTION PURPOSES. BELOW BEAM - COLUMN CONNECTIONS FOR A DISTANCE FROM FACE OF CONNECTION
A. FOOTINGS, FOOTING BEAMS AND GIRDERS -------------- fy = 275 mpa ( 40,000 psi ) NOTE:
B. COLUMNS AND SHEAR WALLS ------------------------------- fy = 275 mpa ( 40,000 psi ) EQUAL TO THE GREATER OF THE OVERALL THICKNESS OF COLUMN, 1 / 6 THE CLEAR HEIGHT
2. IN REFERENCE TO THE DRAWING, SEE ARCHITECTURAL DRAWINGS FOR DEPRESSIONS PURSUANT TO SECTION 4 OF ANNEX "A" OF THE REVISED
OF COLUMN OR 450mm.
IN FLOOR SLABS, OPENINGS IN THE WALLS AND SLABS, INTERIOR PARTITIONS, LOCATION C. BEAMS AND GIRDER -------------------------------------------- fy = 275 mpa ( 40,000 psi ) IMPLEMENTING RULES AND REGULATION OF R.A. 9184, APPROVAL
2. COLUMN TIES SHALL BE PROTECTED EVERYWHERE BY A COVERING OF CONCRETE CAST
OF DRAWING ETC. BY AUTHORIZED DPWH OFFICIALS OF DETAILED ENGINEERING
D. NON-LOAD BEARING WALL PARTITION, BEDDED SLABS, FLOOR & ROOF SLABS, MONOLITHICALLY WITH THE CORE WITH THE MINIMUM THICKNESS OF 40mm AND NOT LESS
THAN 40 TIMES THE MAXIMUM SIZE OF COARSE AGGREGATE IN MILLIMETERS. SURVEYS AND DESIGN UNDERTAKEN BY CONSULTANTS NEITHER
3. IN CASE OF DISCREPANCIES AS TO THE LAYOUT, DIMENSIONS, AND ELEVATION BETWEEN PARAPET, CATCH BASIN, SIDE WALK ------------------------- fy = 227.5 mpa ( 33,000 psi )
3. WHERE COLUMNS CHANGE SIZE, VERTICAL REINFORCEMENTS SHALL BE OFFSET AT A SLOPE DIMINISHES THE RESPONSIBILITY OF THE LATTER FOR THE
THE STRUCTURAL PLANS AND ARCHITECTURAL DRAWINGS, THE CONTRACTOR SHALL NOTIFY 2. ALL REINFORCING BARS SIZE 10mm OR LARGER SHALL BE DEFORMED IN ACCORDANCE WITH TECHNICAL INTEGRITY OF THE SURVEYS AND DESIGN NOR
OF NOT MORE THAN 1 IN 6 AND EXTRA 10mm TIES AT 100mm SHALL BE PROVIDED THRU OUT
BOTH THE STRUCTURAL ENGINEER AND THE ARCHITECT. ASTM A 706. BARS SMALLER THAN 10mm MAY PLAIN. TRANSFER ANY PART OF THAT RESPONSIBILITY TO THE APPROVING
THE OFFSET REGION
3. SPLICES SHALL BE SECURELY WIRED TOGETHER & SHALL LAP OR EXTEND IN ACCORDANCE 4. UNLESS OTHERWISE INDICATED IN THE PLANS , LAP SPLICES FOR VERTICAL COLUMN OFFICIALS.
4. ALL CONCRETE WORK SHALL BE DONE IN ACCORDANCE WITH THE ACI. 318 95 BUILDING WITH TABLE A. & TABLE B ( TABLE OF LAP SPLICE & ANCHORAGE LENGTH ) UNLESS OTHERWISE REINFORCEMENT SHALL BE MADE WITHIN THE CENTER HALF OF COLUMN HEIGHT, AND THE
CODE REQUIREMENTS FOR REINFORCED CONCRETE AND ALL STRUCTURAL STEEL WORK SHOWN ON DRAWINGS, SPLICES SHALL BE STAGGERED WHENEVER POSSIBLE. THE DESIGN CONSULTANT SHALL BE HELD FULLY
SPLICE LENGTH SHALL NOT BE LESS THAN 40 BAR . WELDING OR APPROVED MECHANICAL
ACCORDING WITH AISC SPECIFICATION ( 9th EDITION ) IN SO FAR AS THEY DO NOT CONFLICT DEVICES MAY BE USED PROVIDED THAT NOT MORE THAN ALTERNATE BARS ARE WELDED OR RESPONSIBLE FOR THE FAILURE OF THE FACILITY / IES /
WITH THE LOCAL BUILDING CODE REQUIREMENT. MECHANICALLY SPLICED AT ANY LEVEL AND THE VERTICAL DISTANCES BETWEEN THESE STRUCTURES DUE TO FAULTY DESIGN EXCEPT FOR THE CHANGES
WELDS OR SPLICES OF ADJACENT BAR IS NOT LESS THAN 600mm MADE WITHOUT THE CONFORMITY OF THE CONSULTANTS.
5. ACI REFERS TO AMERICAN CONCRETE INSTITUTE, AISC TO AMERICAN INSTITUTE OF STEEL
CONSTRUCTION AND ASTM TO AMERICAN SOCIETY FOR TESTING MATERIALS.
1. ALL SLAB REINFORCEMENTS SHALL BE 20mm CLEAR MINIMUM FROM BOTTOM AND FROM H
6. CONSTRUCTION NOTES AND TYPICAL DETAILS APPLY TO ALL DRAWINGS UNLESS OTHERWISE
TOP OF SLAB.
SHOWN OR NOTED. MODIFY TYPICAL DETAILS AS DIRECTED TO MEET SPECIAL CONDITION. CROSS-TIE

350mm MAX.
2. UNLESS OTHERWISE SHOWN, REINFORCEMENT IN CONTINUOUS SLAB SHALL BE CUT AS 1. UNLESS , OTHERWISE NOTED IN PLANS, CAMBER ALL BEAMS AND GIRDER AT
FOLLOWS. LEAST 6mm FOR EVERY 4.50m OF SPAN, EXCEPT CANTILEVERS FOR WHICH THE
7. SHOP DRAWINGS WITH ERECTION AND PLACING DIAGRAMS OF ALL STRUCTURAL STEEL,
MISCELLANEOUS IRON, PRE-CAST CONCRETE, ETC. SHALL BE SUBMITTED FOR ENGINEERS CAMBER SHALL BE AS NOTED IN PLANS OR AS ORDERED BY THE ENGINEER BUT

10
APPROVAL BEFORE FABRICATION. IN NO CASE LESS THAN 20mm FOR EVERY 3.0m OF FREE SPAN.

H
mi
L1 L2

n.
8. CONTRACTOR SHALL NOTE AND PROVIDE ALL MISCELLANEOUS CURBS, SILLS, STOOLS, 2. TYPICAL BARS BENDING AND CUTTING DETAILS SHALL BE AS SHOWN IN FIG. B - 1
L1/3 L1/3 L2/3
EQUIPMENT'S AND MECHANICAL BASES THAT ARE REQUIRED BY THE ARCHITECTURAL, TOP BAR TOP BAR
ELECTRICAL AND MECHANICAL DRAWINGS.
LAP SPLICES ARE ALLOWED
9. ALL RESULTS OF MATERIAL TESTING FOR CONCRETE, REINFORCING BARS & STRUCTURAL ONLY IN THIS PORTION

CONF. REINF.
L1/6 BOTTOM BAR L1/5 L2/5 BOTTOM BAR JOINT HOOP SPACE @ "2Sh" WHEN THERE ARE
STEEL MUST BE NOTED & APPROVED BY THE STRUCTURAL DESIGNER. BEAMS HAVING WIDTH OF AT LEAST ONE-HALF THE L1 L2 L3

D
COLUMN WIDTH & DEPTHS NOT LESS THAN THREE L2/3 L2/3 L3/3 L3/3
QUARTERS OF THE DEEPEST BEAM THAT FRAME 2D 2D 2D 2D 2D

JOINT REINF.CONF. REINF. PER SCHEDULE CONF. REINF.JOINT REINF.

INTO FOUR SIDES OF THE COLUMN. ALL OTHER
CONDITIONS USE HOOP @ "Sh" CENTER
1. ALL CONCRETE SHALL CONSIST OF A MIXTURE PORTLAND CEMENT TYPE 1, FINE
AGGREGATES, COARSE AGGREGATES AND WATER MIXED IN THE PROPORTION L2/5 L2/5 L3/5 L3/6

0.96
SPECIFIED BY THE ENGINEER, AND SHALL DEVELOP A MINIMUM COMPRESSIVE 3. IF SLABS ARE REINFORCED BOTHWAYS BARS ALONG THE SHORTER SPAN SHALL BE PLACED

Sh
D
STRENGTH AT THE END OF TWENTY EIGHT ( 28) DAYS W/ CORRESPONDING MAXIMUM BELOW THOSE ALONG THE LONG SPAN AT THE CENTER AND OVER THE LONGER SPAN BOTTOM BARS WEB BARS
2-12mm SIDE BARS
SIZE AGGREGATE & SLUMPS AS FOLLOW. FOR REINFORCING BARS NEAR THE SUPPORTS. THE SPACING OF THE BARS AT THE COLUMN TOP BARS
FOR COL. BAR SPLICES SEE TABLE OF MIN. LAP

COLUMN TIES AS
STRIPS SHALL NOT BE MORE THAN ONE AND A HALF ( 1 21 ) SLAB THICKNESS
SPLICE LENGTH OF COLUMN REINFORCEMENT
ALL OTHERS, INCLUDING 4. TEMPERATURE BARS FOR SLAB SHALL BE GENERALLY PLACED NEAR THE FACE IN TENSION (SPACING OF TIES ALONG THIS REGION SHALL NOT
SUSPENDED SLABS 4000 psi ( 27.6 mpa ) 20mm 100mm BE LESS THAN 100mm)
AND SHALL NOT BE LESS THAN 0.0025 x GROSS CROSS-SECTIONAL AREA ( Ag ) OF THE SLAB
COLUMNS 4000 psi ( 27.6 MPA ) 20mm 100mm ( SEE SCHEDULE BELOW )
TABLE "A" TABLE "B"
BEAMS, SLABS 4000 psi ( 27.6 MPA ) 20mm 100mm TENSION BARS COMPRESSION BARS
EMBEDMENT LENGTHS AND LAPPED EMBEDMENT LENGTHS AND LAPPED
SLAB ON FILL

Sh
3000 psi ( 27.6 MPA ) 20mm 100mm SPLICES IN MILLIMETERS SPLICES IN MILLIMETERS

D
BAR SIZE fc' = 20.7MPa (3000psi) fc' = 20.7MPa (4000psi) BAR SIZE fc' = 20.7MPa (3000psi) fc' = 20.7MPa (4000psi)
2. MAINTAIN MINIMUM CONCRETE COVER FOR REINFORCING STEEL AS FOLLOWS SCHEDULE OF MINIMUM SLAB REINFORCEMENT (DEFORMED) EMBEDMENT LAPPED (DEFORMED) EMBEDMENT LAPPED
EMBEDMENT LAPPED EMBEDMENT LAPPED
SUSPENDED SLABS ------------------------------------------------------------------ 20mm NOTE:
THICKNESS MINIMUM TEMPERATURE BARS 10mm 300 300 300 300 10mm 225 300 200 300
SLAB ON GRADE ----------------------------------------------------------------------- 40mm ALL CONCRETE REINF. DETAIL SHOULD BE
WALLS ABOVE GRADE --------------------------------------------------------------- 25mm 100mm 10mm @ 250mm EACH WAY DONE IN ACCORDANCE WITH THE LATEST 12mm 300 300 300 300 12mm 275 300 250 300
BEAM STIRRUPS AND COLUMN TIES ----------------------------------------------- 40mm

CONF. REINF.
125mm 10mm @ 225mm EACH WAY EDITION OF ACI DETAILING MANUAL. 16mm 300 400 300 400 16mm 350 400 325 400
WHERE CONCRETE IS EXPOSED TO 20mm 20mm
400 550 350 500 450 500 475 500

D
EARTH BUT POURED AGAINST FORMS -------------------------------------------- 50mm 150mm 10mm @ 185mm EACH WAY
25mm 25mm
WHERE CONCRETE IS DEPOSITED 600 800 550 750 550 625 550 625
175mm 10mm @ 150mm EACH WAY 28mm 28mm
750 1000 650 850 625 675 625 675
DIRECTLY AGAINST THE EARTH ----------------------------------------------------- 75mm
3. CONCRETE SHALL BE DEPOSITED IN ITS FINAL POSITION WITHOUT SEGREGATION. 200mm 10mm @ 140mm EACH WAY 32mm 950 1300 850 1100 32mm 700 775 700 775
RE-HANDLING OR PLACING SHALL BE DONE PREFERABLY WITH BUGGIES, BUCKETS OR
WHEELBARROWS, NO CHUTES WILL BE ALLOWED EXCEPT TO TRANSFER CONCRETE FROM
HOPPER TO BUGGIES, WHEELBARROWS OR BUCKETS IN WHICH CASE THEY SHALL NOT EXCEED 3. IF THE BEAM REINFORCING BARS END IN A WALL THE CLEAR DISTANCE FROM THE BAR TO THE
SIX ( 6 ) METERS IN AGGREGATE LENGTH. FARTHER FACE OF THE WALL NOT BE LESS THAN 25mm. EMBEDMENT LENGTH SHALL BE AS
4. NO DEPOSITING OF CONCRETE SHALL BE ALLOWED WITHOUT THE USE OF VIBRATORS SHOWN IN A TABLE "A" FOR TENSION BARS AND TABLE "B" FOR COMPRESSION BARS UNLESS
LAP SPACE LENGTH: SPECIFIED IN PLAN. TOP BAR SHALL NOT BE SPLICED WITHIN THE COLUMN. AT LEAST TWO
UNLESS AUTHORIZED IN WRITING BY THE DESIGNERS AND ONLY FOR UNUSUAL CONDITIONS
5. UNLESS OTHERWISE NOTED IN THE PLANS ALL BEDDED SLABS SHALL BE REINFORCED WITH AT ANY LEVEL NO MORE THAN ALTERNATE BARS SHOULD BE SPLICED MIN. STIRRUPS SHALL BE PROVIDED AT ALL SPLICES.
WHERE VIBRATIONS IS EXTREMELY DIFFICULT TO ACCOMPLISH.
10mm AT 250mm O.C EACH WAY TO CENTER OF SLAB AND CONSTRUCTION JOINTS FOR SAME DISTANCE BETWEEN TWO ADJACENT BARS SPLICES SHALL BE 600mm.
5. ALL ANCHOR BOLTS, DOWELS, AND OTHER INSERTS, SHALL BE PROPERLY POSITIONED & SHALL NOT BE LESS THAN 3.65 METER APART
SECURED IN PLACE PRIOR TO PLACING OF CONCRETE. 4. IF THERE ARE TWO OR MORE LAYERS OF REINFORCING BARS, USE 25mm BAR SEPARATORS
SPACED AT 1.0m ON CENTER IN NO CASE SHALL THERE BE LESS THAN TWO
6. ALL CONCRETE SHALL BE KEPT MOIST FOR A MINIMUM OF SEVEN ( 7 ) CONSECUTIVE DAYS 6. PROVIDE EXTRA REINFORCEMENTS FOR CORNER SLAB ( TWO ADJACENT DISCONTINUOUS
( 2 ) SEPARATORS BETWEEN TWO LAYERS OF BARS.
IMMEDIATELY AFTER POURING BY THE USE OF WET BURLAP, FOG SPRAYING, CURING EDGES ) AS SHOWN BELOW.
COMPOUNDS OR OTHER APPROVED METHODS. 5. MINIMUM CONCRETE PROTECTION FOR REINFORCING BARS OR STEEL SHAPES BE AS
7. CONCRETE SLAB REINFORCEMENTS SHALL BE PROPERLY SUPPORTED WITH 10mm STEEL
7. STRIPPING OF FORMS AND SHORES : CHAIR OR APPROVED EQUIVALENT SPACED AT 1.0 METER ON CENTER BOTHWAYS SHOWN IN FIG. B - 2 UNLESS SPECIFIED ELSEWHERE.
FOUNDATION -------------------------------------------------------------------------- 24 hrs.
SUSPENDED SLAB EXCEPT WHEN ----------------------------------------------- 8 days A
ADDITIONAL LOADS ARE IMPOSED
WALLS --------------------------------------------------------------------------------- 24 days 12 x 1000 LONG @
MID-DEPTH OF SLAB b
BEAMS --------------------------------------------------------------------------------- 24 days DOWN INTO EDGE BEAM. EXTENDED
4- 12@ 1800 LONG TOP BARS BEND @ EACH CORNER LAP SPLICE LENGTH:
COLUMNS ----------------------------------------------------------------------------- 24 days
BARS MINIMUM OF 1200 ( 4'-0" ) INTO BARS. 1- 12 TOP & AT ANY LEVEL NO MORE THAN

t
8. THE CONTRACTOR SHALL SUBMIT THE SCHEDULE OF POURING AND THE LOCATION OF THE
BOTTOM BARS ALTERNATE BARS SHOULD BE MAIN REINFORCEMENT
CONSTRUCTION JOINTS TO THE STRUCTURAL ENGINEER AT LEAST ( 4 ) DAYS PRIOR TO THE SPLICED. MIN. DISTANCE BET. see note
4- 12 BOTTOM BARS WEB BARS

t or 1/4D
WITHIN CENTER
POURING FOR APPROVAL.
400

ht
1- 12 EA. TWO ADJACENT BARS SPLICES see note

HALF OF "H"

t
9. THE CONTRACTOR SHALL FURNISH AND MAINTAIN ADEQUATE FORMS AND SHORING UNTIL TOP & BOTTOM SHALL BE 600mm. SLEEVES FOR UTILITY
THE CONCRETE MEMBERS HAVE ATTAINED THEIR WORKING CONDITION AND STRENGTH

D
PIPES MAX 1/5D
L/4
0

SLAB
38mm
0

OPENING TOP BARS @ SUPPORT (CONT.) 0.025m SEPARATOR

6

CLEAR see note PROVIDE 3-10 EXTRA STIRR.

REQ'D. BOTT. BARS @ SUPPORT EACH SIDE OF SLEEVES
JT. REINF.
400

1. FOOTINGS ARE DESIGNED FOR AN ALLOWABLE SOIL BEARING PRESSURE OF 96 kpa

0

1- 12 EA.
0

( 2000 psf ). CONTRACTOR SHALL REPORT TO THE ENGINEER, IN WRITING, THE ACTUAL TOP & BOTTOM

D
6

SOIL CONDITION UNCOVERED AND CONFIRM ACTUAL BEARING CAPACITY OF SOIL BEFORE
DEPOSITING CONCRETE. INTO TWO WAY SLAB EXTEND 6. WHEN A BEAM CROSSES A GIRDER, REST BEAM ON TOP OF GIRDER BARS, BEAM
BARS UP TO BEAM SUPPORT REINFORCING BAR SHALL BE SYMMETRICAL ABOUT CENTER LINE WHENEVER POSSIBLE.
2. FOOTINGS SHALL REST AT LEAST 15800mm BELOW NATURAL GRADE LINE UNLESS OMIT TRIMMER BARS WHERE
6

OTHERWISE INDICATED IN PLANS. NO FOOTING SHALL REST ON FILL. OPENING IS FRAMED BY BEAM BOTTOM BARS AT 7. GENERALLY NO SPLICES SHALL BE PERMITTED AT POINTS WHERE CRITICAL BENDING
0

SPLICE
0

MID SPAN STRESSES OCCUR, SPLICES WHERE NO PERMITTED SHALL BE INDICATED IN THE TABLE "A"
3. MINIMUM CONCRETE PROTECTION FOR REINFORCEMENTS SHALL BE 75mm CLEAR AND "B" WELDED SPLICES SHALL BE DEVELOP IN TENSION AT LEAST 125% OF THE
EXTRA TOP BARS
FOR CONCRETE DEPOSITED THE GROUND AND 50mm FOR CONCRETE SPECIFIED YIELD STRENGTH OF THE BAR. NOT MORE THAN 50% OF THE BARS AT ANY ONE
DEPOSITED AGAINST A FORMWORK. @ SUPPORT SECTION IS ALLOWED TO BE SPLICED THEREIN.

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 2. DESIGN STRESS
1. ALL WALLS SHALL BE REINFORCED ACCORDING TO THE FOLLOWING SCHEDULE OF WALL A. CONCRETE
REINFORCEMENT UNLESS OTHERWISE INDICATED IN THE PLANS.

(DOWEL)
1. UNLESS OTHERWISE SHOWN IN PLANS ALL CONCRETE HOLLOW BLOCKS AND CERAMIC BLOCKS COMPRESSIVE STRENGTH AT 28 DAYS fc' = 20.70 MPa ( 3,000 psi)

VERIFY ARCHITECTURAL
400
SHALL BE REINFORCED AS SHOWN IN THE SCHEDULE OF CONCRETE HOLLOW BLOCKS AND B REINFORCING BARS
CERAMIC BLOCK REINFORCEMENT a) FOR BARS 16mm AND GREATER fy = 275 MPa (40,000 psi)
2. PROVIDE 150mm X 300mm STIFFENER COLUMN REINFORCED WITH 4 -12mm WITH 6mm TIES AT b) FOR BARS LESS THAN 16mm fy = 230 MPa (33,000 psi)
150mm ON CENTER WHERE CONCRETE HOLLOW BLOCK TERMINATES AND AT EVERY 3.00m C STRUCTURAL STEEL, ASTM - A36
LENGTH OF CONCRETE HOLLOW BLOCK WALLS UNLESS NOTED IN STRUCTURAL PLANS. FOR TRUSSES, BRACINGS, AND STRUTS fy = 248MPa (36,000 psi)
D PURLINS
COLD FORMED LIGHT CAGE SHAPES fy = 248MPa (36,000 psi)
REINFORCING BARS SHALL HAVE 25mm CLEAR CONCRETE COVER FROM FACE OF WALL EXCEPT E MASONRY UNIT (CHB)

(DOWEL)
SCHEDULE OF CONCRETE HOLLOW BLOCK AND CERAMIC BLOCK REINFORCEMENT FOR WALLS IN CONTACT WITH THE GROUND WHERE A MINIMUM OF 60mm SHALL BE PROVIDED, NON - LOADING BEARING CHB WALLS fm' = 3.45 MPa (500psi)

400
AND FOR EXPOSED FACES FORMED WALLS WHERE THE MINIMUM SHALL BE 50mm CLEAR. F WELDS - USED E - 60xx ELECTRODE
2. CARRY VERTICAL BARS AT LEAST 60mm ABOVE FLOOR LEVEL TO PROVIDE FOR SPLICES WHEN G STRUCTURAL BOLTS, ASTM - A307
NECESSARY STOP AT 50mm BELOW TOP SLAB OR SOLID BAND WHERE THE WALL ENDS a) Ft = 96.60 MPa (14,000 psi) b) Fv = 69MPa(10,000 psi)
VERTICAL AND HORIZONTAL BARS SHALL BE SPLICED BY LAPPING A DISTANCE EQUAL TO 30
AND WIRED SECURELY WITH 16 G.I. WIRE PROVIDED THAT SPLICES IN ADJACENT BARS ARE
STAGGERED AT LEAST 1.50M OC
3. UNLESS OTHERWISE NOTED IN THE PLANS, ALL OPENINGS IN WALLS 250mm OR THICKER SHALL 1 WHERE A CONSTRUCTION JOINT IS TO BE MADE, THE SURFACE OF CONCRETE SHALL BE
BE REINFORCED AROUND WITH 2 - 20mm BARS FOR 225mm, 200mm, 175mm, 150mm, USE 2 - 16mm CLEANED AND ALL LAITANCE AND STANDING WATER REMOVED. SHEAR KEY SHALL BE
. FOR 125mm AND 100mm WALLS, USE 2 - 12mm BARS. ALL WALLS SPANNING SHALL HAVE PROVIDED AT THE JOINT.
VERTICAL REINFORCEMENT BENT TO A U - FORM LIKE STIRRUPS AND SPACED ACCORDING TO THE
SCHEDULE UNLESS OTHERWISE NOTED ( SEE FIG. 1 )

550
30 BAR DIA. 30 BAR DIA.

t/3
LINTELS IN BLOCK WALLS 40

500
(min.) (min.)
CLEAR TOTAL MIN. HEIGHT
50

VARIES

t/3
SPAN LENGTH fc' OF

t
("L") (L + 0.40m) (MPa) LINTEL

D/3 D/3
BOTTOM TOP STIRRUPS
(mm)

D/3

D
600 (MIN.)

t/3
1.20m 1.60m 200 1- 10 1- 10 6mm @ 200mm
1.50m 1.90m 14.0 200 1- 10 1- 10 6mm @ 200mm 500 550
1.80m 2.20m 200 1- 12 1- 10 6mm @ 200mm

250
2.10m 2.50m 250 1- 12 1- 10 6mm @ 200mm
2.40m 2.90m 17.0 250 1- 12 1- 10 6mm @ 200mm
2.70m 3.10m 250 1- 16 1- 12 10mm @ 200mm

3.00m 3.40m
20.0
300 1 - 16 1- 12 10mm @ 200mm 400
3.30m 3.70m 300 1 - 16 1- 12 10mm @ 200mm
3.60m 4.00m 300 1 - 20 1- 12 10mm @ 200mm
1. USE E70xx ELECTRODES FOR ALL MEMBERS WELDED.
2. WELDS SHALL DEVELOP THE FULL STRENGTH OF MEMBERS JOINED UNLESS OTHERWISE SHOWN
OR DETAILED IN THE DRAWINGS.

300
(TYP.)
1. STRUCTURAL STEEL TO BE USED FOR FABRICATION AND ERECTION OF THIS STRUCTURE SHALL

DOWEL
COMPLY WITH ALL THE PERTINENT PROVISION OF AISC SPECIFICATION OR DESIGN, FABRICATION

400
DOWEL

AND ERECTION OF STRUCTURAL STEEL FOR BUILDING LATEST EDITION.

400

2. ALL STRUCTURAL STEEL SHAPES SHALL CONFORM TO ASTM A36 STRUCTURAL STEEL UNLESS 38mm CLEAR
OTHERWISE INDICATED.

250
3. ALL WELDED CONNECTIONS SHALL DEVELOP THE FULL STRENGTH OF THE MEMBERS CONNECTED.
4. UNLESS OTHERWISE SPECIFIED ALL WELDING RODS SHALL CONFORM AWS E60 ELECTRODES.
5. ALL BOLTS USED UNLESS OTHERWISE SPECIFIED SHALL BE ASTM A 307 BOLTS.
400

A. ALL EMBEDDED PIPES FOR UTILITIES, ETC. THAT PASS THRU BEAMS SHALL NOT EXCEED 100mm IN
OR 1 / 3 BEAM DEPTH WHICHEVER IS LESS, UNLESS OTHERWISE APPROVED IN WRITING BY THE
STRUCTURAL ENGINEER
B. NO PIPES SHALL BE ALLOWED TO PASS THRU BEAMS VERTICALLY. NOTES OF STIRRUPS:
C. NO PIPES SHALL BE EMBEDDED IN COLUMNS.
1 ALL REINFORCEMENT SHALL BE BENT COLD UNLESS
300 OTHERWISE PERMITTED BY THE STRUCTURAL

DOWEL
(TYP) ENGINEER.

400
DOWEL

2 REINFORCEMENT PARTIALLY EMBEDDED IN CONCRETE

400

SHALL NOT BE FILLED BENT, EXCEPT AS SHOWN IN

250 1. LOADINGS THE DESIGN DRAWINGS OR PERMITTED BY THE
A. DEAD LOAD STRUCTURAL ENGINEER.
400 CONCRETE - 23.56 KN / m3 3 TIES AND CLOSE STIRRUPS MUST BE
DOWEL STEEL - 76.93 KN / M3 db
150mm THK. CHB WALL - 2.73 kPA

db
1.25 L
100mm THK. CHB WALL - 2.11 kPA

D + 2db

L
D
B. LIVE LOAD
ROOF - 1.00 kPA 4db or 65mm

C. WIND LOAD ( NSCP 2010 )

D
db
BASIC WIND VELOCITY, V = 250 KPH
200(mm) 200(mm) P = qh [(GCpf) - (GCpi)] (DESIGN WIND PRESSURE)
WHERE: qh = VELOCITY PRESSURE, kPA

db
GCpf = EXTERNAL PRESSURE COEFFICIENT
VERIFY DEPRESSION

30 BAR DIA. 30 BAR DIA GCpi = INTERNAL PRESSURE COEFFICIENT

12db

L
NOTE:
(min.) (min.) PURSUANT TO SECTION 4 OF ANNEX "A" OF THE D. SEISMIC LOAD ( NSCP 2010 )
D = FOR BEAM
t = FOR SLAB

REVISED IMPLEMENTING RULES AND REGULATION V = [( Cvl / RT ) W] ( DESIGN BASE SHEAR ) D

OF R.A. 9184, APPROVAL BY AUTHORIZED DPWH L
OFFICIALS OF DETAILED ENGINEERING SURVEYS Vmax = ( 2.50CAL / R ) W Vmin = 0.11 CalW
Vmin = ( 0.80 ZNvl / R ) W (ZONE 4) L1
AND DESIGN UNDERTAKEN BY CONSULTANTS
200 (DOWEL)

NEITHER DIMINISHES THE RESPONSIBILITY OF THE

LATTER FOR THE TECHNICAL INTEGRITY OF THE WHERE : W = TOTAL DEAD LOAD
400

SURVEYS AND DESIGN NOR TRANSFER ANY PART

OF THAT RESPONSIBILITY TO THE APPROVING T = NATURAL PERIOD = Ct (hn) ;
OFFICIALS. WHERE : C = NUMERICAL COEFFICIENT
h = BUILDING HEIGHT
D = FOR BEAM THE DESIGN CONSULTANT SHALL BE HELD I = IMPORTANCE FACTOR = 1.50
2t = FOR SLAB FULLY RESPONSIBLE FOR THE FAILURE OF THE
R = NUMERICAL FACTOR = 8.50
FACILITY / IES / STRUCTURES DUE TO FAULTY
30 BAR DIA. DESIGN EXCEPT FOR THE CHANGES MADE WITHOUT SEISMIC COEFFICIENT Cv = 0.44Nv
THE CONFORMITY OF THE CONSULTANTS. Ca = 0.64N
(min.)
NEAR SOURCE FACTOR ( 10km ) Nv = 1.20
Na = 1.00
Z = SEISMIC ZONE = 0.40 ( ZONE 4 )
S = SOIL TYPE = D

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 FOOTING DIMENDIONS (mm) REINFORCEMENT REMARKS
FOOTING LENGTH WIDTH X Y Z THICKNESS DEPTH BAR - X BAR - X
MARK (L) (W) (m) (m) (m) (T) (D) TOP BOTTOM TOP BOTTOM
COMBINED FOOTING
CF - 1 6 3.50 1.30 2.50 2.20 0.50 2.10 @ 0.15 @ 0.10 @ 0.30 @ 0.15
ALONG GRID B & C

F-3 3.40 3.40 - - - 0.50 2.10 @ 0.175 @ 0.175 @ 0.175 @ 0.175 ALONG GRID A

FLOOR BEAM DIMENSIONS

LEVEL BEAM
DIMENSION 0.40 X 0.40 0.45 X 0.45 0.45 X 0.45
( in / mm )
MAINBARS 12 -20mm 12 - 25mm 12 - 25mm MARK B D REBAR LEFT MID SPAN RIGHT SUPPORT 2D MID SPAN
LATERAL TIES ( 10mm ) 3@50mm; 3@100mm, 3@150mm REST @ 200mm O.C 3@50mm; 3@100mm, 3@150mm REST @ 200mm O.C 3@50mm; 3@100mm, 3@150mm REST @ 200mm O.C
(mm ) TOP BOTTOM TOP BOTTOM TOP BOTTOM BAR SPACING TYPE BAR SPACING TYPE

FOUNDATION
FTB - 1 0.30 0.50 20mm 6 6 4 4 6 6 10 100 B 10 200 A

FTB - 2 0.30 0.50 20mm 6 6 4 4 6 6 10 100 B 10 200 A

FTB - 3 0.30 0.50 20mm 3 3 3 3 3 3 10 100 B 10 200 A

DIMENSION 0.40 X 0.40 0.55 X 0.55 0.55 X 0.55

MAINBARS 12 - 20mm 12-25mm 12 - 25mm
LATERAL TIES ( 10mm ) 3@50mm; 3@100mm, 3@150mm REST @ 200mm O.C 3@50mm; 3@100mm, 3@150mm REST @ 200mm O.C 3@50mm; 3@100mm, 3@150mm REST @ 200mm O.C

100mm THK. CHB ALL CELLS 150mm CHB (ALL CELLS ARE
ARE FILLED w/ MORTAR FILLED WITH MORTAR)
10mm HOR. BARS @ 600mm O.C
100mm HOR. BARS @ 10mm VERT. BARS @ 600mm O.C
600mm O.C.
100mm VERT. BARS @
DIMENSION 0.40 X 0.40 0.575 X 0.575 0.55 X 0.55 600mm O.C. NAT. GRADE LINE
MAINBARS 4 - 25mm, 8 - 20mm 12 - 25mm 12 - 25mm 0.40
LATERAL TIES ( 10mm ) 3@50mm; 3@100mm, 3@150mm REST @ 200mm O.C 3@50mm; 3@100mm, 3@150mm REST @ 200mm O.C 3@50mm; 3@100mm, 3@150mm REST @ 200mm O.C 12mm BARS @ 400mm O.C. 12mm RSB
TRANSVERSE BARS @0.60mm OC
3 - 12mm EQUALLY SP.
FFL LONGITUDINAL BARS

0.10
0.15m THK. WALL

0.15

0.20
FOOTING 10mm RSB VERT.
3 - 12mm EQUALLY SPACED BARS @ 0.60m OC
GRAVEL BED 12mm 400mm O.C
LONGITUDINAL BARS TRANSVERSE BARS
0.15 0.30 0.15
DIMENSION 0.435 X 0.435 0.610 X 0.610 0.585 X 0.585
MAINBARS 12-25mm 12 - 25mm 12 - 25mm
LATERAL TIES ( 10mm ) 3@50mm; 3@100mm, 3@150mm REST @ 200mm O.C 3@50mm; 3@100mm, 3@150mm REST @ 200mm O.C 3@50mm; 3@100mm, 3@150mm REST @ 200mm O.C
DETAIL OF WALL FOOTING (WF-2) DETAIL OF WALL FOOTING (WF-1)
SCALE 1:20mts SCALE 1:20mts

1 2 3 4 5 6 7 8 9
36.00 NGL NGL
4.50 9.00 9.00 9.00 4.50
4.50 4.50 4.50 4.50 4.50 4.50

D
FTB-1 FTB-2 FTB-2

T
A 6.00 3.40
SECTION 50mm LEAN SECTION
CONCRETE
200mm R.C MICRO-PILE
(SEE DETAILS)
200mm R.C MICRO-PILE
(SEE DETAILS) C B A
7.00

X = 1.30m Y = 2.50 Z = 2.20 L = 3.40

9.50

W = 3.40
W = 3.50
2.50

PLAN PLAN

FOUNDATION PLAN TYPICAL FOOTING DETAIL

SCALE 1:100mts SCALE 1:50mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 5
120 1. CONCRETE:
3 MIN
THE MINIMUM 28-DAY COMPRESSIVE STRENGTH
OF CONCRETE
GROUT, f'c SHALL BE 20.6 MPa (3,000 psi)
2. REINFORCEMENT:
THE MINIMUM YIELD STRENGTH OF REINFORCING
150
D

BARS fy SHALL
BE 275 MPa (40,000 psi)

D
WELDED SPIRAL TIE SPLICE DETAIL 150 x 65 x 20 x
SCALE NTS
2.0mm LC PURLINS
65 x 65 x 6mm x 140mm LONG CLIP
0.30 ANGLE FULL WELD (VERTICALLY)
100 x 100 x 6mm THK.
T

PILE REBARS DOWELED INTO 0.05 ANGULAR BASE PLATE

CAST-IN-PLACE FOOTING 8 - 20mm LONGITUDINAL

T
REINFORCEMENT

0.05
0.30
10mm SPIRAL TIES 12mm x 150mm LONG VERT. & HOR.
ANCHOR BOLTS SPACED @ 500mm
O.C. ( SPACED ALTERNATELY) LRB-1
300mm x 300mm R.C. PILE
(TYP. 5 PLACES PER FOOTING 3) SECTION
12.0m LONG

A A TYPICAL ELEVATION OF RC-PILE

COLUMN FOOTING ELEVATION (CF-3)
SCALE 1:30mts

SCALE 1:30mts

VARIES
65 x 65 x 6mm x 140mm LONG
CLIP ANGLE FULL WELD

0.05
150 x 65 x 20 x
3.50 2.0mm LC PURLINS

5 @ 0.05m PITCH
1.75 1.75
2.20

100 x 100 x 6mm THK.

ANGULAR BASE PLATE
LRB-1
TYPICAL ELEVATION OF RC-PILE 12mm x 150mm LONG VERT. & HOR. ANCHOR

BALANCE @ 0.10m PITCH

BOLTS SPACED @ 500mm O.C. ( SPACED
ALTERNATELY)

SPIRAL TIES
SCALE 1:30mts

B 0.60
3.40
0.60
EXTERIOR

VARIES
0
0.5

10mm
0.60
6.00

0
300mm x 300mm R.C. PILE 65 x 65 x 6mm x 140mm LONG CLIP 0.5
(TYP. 5 PLACES PER ANGLE FULL WELD (VERTICALLY)
2.50

1.70

FOOTING 3)
0
150 x 65 x 20 x 0.5
2.0mm LC PURLINS

0
0.5
A

1.00

1.00
3.40

5 @ 0.05m PITCH
100 x 100 x 6mm THK.
ANGULAR BASE PLATE

C
5
0.2 12mm x 150mm LONG VERT. & HOR.
ANCHOR BOLTS SPACED @ 500mm

0.15
1.70

5
O.C. ( SPACED ALTERNATELY)

0.2
1.30

ELEVATION
BENT PLATE 100 x 100
x 12 x 200mm LONG
0.05 0.05
0.60

0.60

0.60 0.60
CONNECTION OF
COLUMN FOOTING DETAILS (CF-1) COLUMN FOOTING DETAILS (CF-3) TYPICAL ELEVATION OF RC PILE PURLINS TO LRB-1
SCALE 1:30mts SCALE 1:30mts SCALE 1:15mts SCALE 1:15mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 L
L1 L1 L/4 L/2 L/4

0.10
LAP SPLICES ARE ALLOWED LAP SPLICES ARE ALLOWED
2D ONLY IN THIS PORTION 2D 2D ONLY IN THIS PORTION 2D

RCB-1 RCB-1
10mm CUTBARS
12mm BENTBARS 10mm TEMP.BARS @0.10m OC, BOTHWAYS
@0.20m OC, BOTHWAYS @0.20m OC, BOTHWAYS

TYPICAL SLAB ELEVATION

TYPICAL BEAM ELEVATION SCALE NTS
SCALE NTS

1 2 3 4 5 6 7 8 9
36.00
4.50 4.50 4.50 4.50 4.50 4.50 4.50 4.50

DC-1 DC-1 DC-1 DC-1

7.00

1.275

DC-1 DC-1 DC-1 DC-1

9.50

3.85

B
2.50

C
SECOND & THIRD FLOOR FRAMING PLAN
SCALE 1:100mts

WIDTH
WIDTH
DESIGN CRITERIA:
DEPTH

i. LIVE LOAD ________________________________1000Pa

DEPTH

ii. ALLOWABLE STRESSER

1. CONCRETE
a. FOR FOOTING, BEAMS AND SLABS
fc" = 20 MPa
2. CONCRETE MASONRY UNITS

TYPE OF STIRRUPS (LOAD BEARING CHB)

fm' = 6.90 MPa, fM = 2.41 MPa
SCALE NTS
3. REINFORCING STEEL BARS

fy = 230 MPa
4. ASSUMED ALLOWABLE BEARING CAPACITY
Y = 100KPa
NOTE:

WATER TABLE IS 1500 BELOW GROUND LEVEL.

SLOPE DIRECTION OF FLOOR DRAIN

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 1 2 3 4 5 6 7 8 9
36.00
4.50 4.50 4.50 4.50 4.50 4.50 4.50 4.50

1.50
A

7.00
B

2.50
C
1.50

ROOF FRAMING PLAN @ BOTTOM CHORD LEVEL

SCALE 1:100mts

1 2 3 4 5 6 7 8 9
36.00
0.60 4.50 4.50 4.50 4.50 4.50 4.50 4.50 4.50 0.60
12mm. THREADED SAGROD
w/ STD. NUTS & WASHER
1.50

A
6.25
7.00

B
6.25
2.50

C
1.50

16mm. PLAIN BAR CROSS 2mm x 150 x 50mm. L.C PURLINS SP. @
BRACE w/ STD. TURN BUCKLE
CLEATS VERTICALLY WELD (SEE DETAIL)
ROOF FRAMING PLAN @ TOP CHORD LEVEL
SCALE 1:100mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 0.40

0.30 0.05

0
0 .4
0.168

0.4
0
0.40
0.10
PC-1
0.30

0.10
0.10 0.40 0.10 SPOT DETAIL
0.20 SCALE 1:20mts

ROOF DETAIL @ END BAY

0.4
SPOT DETAIL SPOT DETAIL SPOT DETAIL

0
SCALE 1:15mts
SCALE 1:20mts SCALE 1:20mts SCALE 1:20mts

0.20

0.40
0.20

0.10
0.10
0.15
SPOT DETAIL 12 x 12mm DRIP MOLD
SCALE 1:20mts
0.45

SECTION OF STAIR SLAB DETAIL OF DC-1 0.417

0
SCALE 1:10mts SCALE 1:20mts

0.4
0.60
5 6 CONCRETE SUN-BREAKER DETAILS
SCALE 1:10mts
0.30

0.40
0.50
SPOT DETAIL

0.25
0.10
SCALE 1:20mts

0.45
PC-1
DETAILED SECTION OF RAMP STAIR FRAMING PLAN DET. SECTION OF PC-1
SCALE 1:10mts
SCALE 1:30mts SCALE 1:50mts

4.75 4.75

4.70 B A
7.00

3 6.9
6.9 3
2.50
3.20

PC-1
7.00
4.00

3.20
0.325

B 1.50 7.00 2.50 1.50

STAIR FRAMING PLAN STAIR SECTION DETAIL ELEV. OF END WALL FRAME
SCALE 1:75mts SCALE 1:75mts SCALE 1:30mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 0.25
LC - 150mm x 65mm x 20mm x 2mm
6mm THK GUSSET PLATE WELDED TO 12mm THK STIFFENED FLANGE LIGHT CAGE PURLINS
TRUSS TOP CHORD & 65mm x 65mm x BASE PLATE
0.15 0.25
6mm
65 200 65 TRUSS TOP CHORD
2- 65mm x 65mm x 6mm 2- 65mm x 65mm x 6mm 2- 75mm x 75mm x 6mm

0.25
A
2- 75mm x 75mm x 6mm 2- 75mm x 75mm x 6mm 2- 65mm x 65mm x 6mm

6mm THK

0.40
GUSSET PLATE
65mm x 65mm x 6mm 6mm THK 6mm THK ( TYPICAL )
25mm THK LEVELING GROUT GUSSET PLATE GUSSET PLATE

0.25

0.25
( TYPICAL ) ( TYPICAL )
190 75

6mm THK
340

12mm SAGROD GUSSET PLATE

( TYPICAL )

0.50 SPOT DETAIL "D" SPOT DETAIL "E" SPOT DETAIL "F"
615 SCALE 1:10mts SCALE 1:10mts SCALE 1:10mts

SPOT DETAIL "B" SPOT DETAIL "C"

SCALE 1:10mts SCALE 1:10mts
4-12mm x 250mm LONG
SPOT DETAIL "A" ANCHOR BOLTS w/ NUTS & WASHER SCHEDULE OF TRUSSES MEMBERS AND WELDS
SCALE 1:10mts SIZE WELD ( mm )
NAME TRUSS MEMBERS LENGTH
16mm STEEL THICKNESS REMARKS
0.15 ( mm ) L1 L2 L3
6mm THK 400 65 77 65 2- 75mm x 75mm x 6mm CROSS BRACING
2 s-75 x 75 x 6 ( A )
GUSSET PLATE 6 25 25 A 6 FULL WELD
2- 65mm x 65mm x 6mm ( TOP & BOTTOM CHORDS )
69
118

8 2 - 50mm x 50mm x 6mm 100 75 50

65
B 2 s-50 x 50 x 6 ( B ) 6
75

50

75
6 TOP CHORD

0.25
6mm THK
4-16mm x 350mm LONG GUSSET PLATE
BOTTOM CHORD L1

190
ANCHOR BOLTS w/ NUTS

220
322
223

( TYPICAL )
& WASHER
STITCH WELD
134
75

75
65mm x 65mm x 6mm

65
456 619

L3
CROSS BRACING
DETAIL OF GUSSET PLATE DETAIL OF ANCHORAGE SPOT DETAIL "F" DETAIL CONNECTION L2 L1
SCALE 1:10mts SCALE 1:10mts
SCALE 1:10mts SCALE 1:10mts

WELD DETAIL
A B C
SCALE NTS

0.60
0.03 0.03
4.75 4.75
0.05 0.05

0.03
1.25 1.25 1.13 1.13

0.05
SEE DETAILS
0.40mm THICK (BASE METAL THICKNESS) LONG
0
0.5 SPAN PRE PAINTED G.I ROOFING SHEETS WITH

0.60
TOTAL COATED THICKNESS OG 0.50mm THK.
0
0.5
12mm. THREADED SAGROD
0
0.5

0.05
w/ STD. NUTS & WASHER

0.03
0
0.5 2mm x 150 x 50mm. L.C PURLINS SP. @
0 4-16 x 450 A307 ANCHOR
0.5 CLEATS VERTICALLY WELD (SEE DETAIL) 12mm THK. BASE PLATE BOLT w/ N & W (TYP.)
0 2 - 50 x 50 x 6mm
0.5
0
WEB MEMBERS
BASE PLATE DETAILS
0.5 SEE DETAILS 2 - 50 x 50 x 6mm TOP SCALE 1:15mts
2.50

0 AND BOTTOM CHORD

0.5
6mm THK. MS ROOFING PANEL
0 GUSSET PLATE
0.5
0
0.5 0.0
0 75 0.60mm (BMT) PRE- PAINTED
0.5
TR
U SS
12mm THK. BASE PLATE
TO
P CH GTUTTER (0.65mm TCT)
OR
D
0
0.5
0
0.5

0.30
SEE DETAILS

0.125
18 SEE DETAILS
0 .2
0.50

SEE DETAILS

LC 100 x 50 x 12 x 1.2mm CONT. w/ 0.15

6mm x 100 x 100 GUSSET
WELDED TO TRUSS TOP CHORD
12 x 300 FICEM FASCIA

TRUSS - 1 DETAILS TRUSS DETAIL @ GUTTER END

SCALE 1:25mts
SCALE 1:8mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 1 2 3 4 5 6 7 8 9

50mm PVC VP
50mm PVC VP (UNDER FLOOR SLAB)
DS DS DS DS DS

A
100mm PVC SP

100mm PVC SS/ VTR

100mm PVC
SS/ VTR
50mm PVC VS 50mm PVC SP 50mm PVC VS
100mm PVC SP 50mm PVC WP 100mm PVC SP
50mm PVC WP
50mm PVC VP SHE HE 50mm PVC VP

C DS
DP

DS
DP DP

DS
DP

DS

8.60
TYPICAL 2nd & 3rd FLOOR PLUMBING LAYOUT 4.00 2.00 2.00
SCALE 1:100mts

2.30
MH MH MH

SEPTIC TANK
USE 1.5 WATER DEPTH

1 2 3 4 5 6 7 8 9

150mm uPVC 150mm CDP 150mm CDP 150mm CDP

CB CB CB CB CB
100mm PVC SP
DS DS DS DS 100mm PVC SP DS

A 100mm PVC SS

50mm PVC VS

100mm PVC SP

50mm PVC VP
CDP

CDP
150mm

150mm
B

C DS DS DS DS

CB CB CB CB
150mm CDP 150mm CDP

200mm CDP TO MAIN 200mm CDP TO MAIN

DRAINAGE SYSYEM DRAINAGE SYSYEM

GROUND FLOOR PLUMBING LAYOUT

SCALE 1:100mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 1 2 3 4 5 6 7 8 9
36.00
0.60 4.50 4.50 4.50 4.50 4.50 4.50 4.50 4.50 0.60
DS DS DS DS DS DS

1.50
A

6.25
7.00
B

6.25
2.50
C

1.50
DS DS DS DS

S-1a 150mm THK. + FIN. SLAB w/ 10mm ROOF DRAINAGE LAYOUT

REBARS @ 300mm O.C BENT UP 2 OUT OF 3 SCALE 1:100mts
@ L/4 FROM FACE SUPPORT BOTHWAYS
8.60
0.15 4.00 0.15 2.00 0.15 2.00 0.15
10mm RSB @200mm
O.C BOTHWAYS
0.15

0.60
0.10 0.40 0.10

100mm PVCDS

25mm PVC

0.10
2.00
2.30

DRAIN PIPE
DRAINAGE PIPE

150mm CDP INLET

0.60
0.40
150mm CDP OUTLET
0.15

S2 150mm THK. + FIN. SLAB w/ 10mm REBARS @ 300mm 16mm HANDLE BAR 0.40
O.C BENT UP 2/3 OUT @ L/4 FACE SUPPORT AND

0.10
8.60 SHORT SPAN 10mm TEMP. BARS @ 300mm EW
PLAN
DETAIL SECTION OF DRAIN PINE
4.00 0.15 2.00 0.15 2.00 SCALE 1:25mts
0.60 0.60 0.60 0.60
150mm THK. SLAB w/
0.15

10mm REBARS @ 0.10 0.40 0.10

300mm BOTHWAYS
0.08 0.08
3 - 10mm (E.W) 16mm HANDLE BAR
0.25

0.30

0.10
0.60
0.25 0.10 0.25
150mm THK CHB w/ 10mm
COMPOUND OR APPLY REBARS HOR. @ 2 LAYER
ONE FACE BITUMEN TAR VERT. @ 600mm O.C
150mm CDP
2.10

0.60
0.40
2% SLOPE
1.50

PLASTERED w/
WATERPROOFING INLET OUTLET

0.10
150mm CDP
2% SLOPE
0.10

0.05 0.05
0.20

0.05 0.50 0.05

SECTION 3 - 10mm REBARS

DETAIL OF SEPTIC TANK CONCRETE WALL w/ HOT APPLIED

DETAIL OF CATCH BASIN MANHOLE COVER DETAIL
SCALE 1:10mts SCALE 1:5mts
SCALE 1:30mts ASPHALT WATERPROOFING (INSIDE FACE)

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 GENERAL PLUMBING NOTES:
1. GRADES OF HORIZONTAL PIPINGS
RUN ALL HORIZONTAL PIPINGS IN PERFECT ALIGNMENT AND AT A FORM GARDE NOT LESS THAN TWO
PERCENT (2%).
2. CHANGE IN DIRECTION

WYES, LONG SWEEP QUARTER BEND, SIXTY-EIGHT OR SIXTEENTH BEND. WHEN THE CHANGE OF
FLOW IS FROM HORIZONTAL TO VERTICAL, A SINGLE 1/8 BEND COMBINATION MAY BE USED ON
1 2 3 4 5 6 7 8 9 VERTICAL STACKS AND SHORT QUARTER BENDS MAY BE USED ON WASTE LINE. TEE AND CROSSES
MAYBE USED IN BENT PIPES.
36.00
3.PROHIBITED FITTINGS
9.00 9.00 9.00 9.00
4.50 4.50 4.50 4.50 4.50 4.50 4.50 4.50 NO DOUBLE HUB OR TEE BRANCH SHALL BE USED ON HORIZONTAL SOIL WASTE LINES, THE
DRILLINGS AND TAPPING OF HOUSE DRAIN, WASTE OR VENT PIPES AND USE OF SADDLE HUB AND
BEND ARE PROHIBITED.

A 4.PIPE CLEAN-OUTS
5.CLEAN-OUTS ARE REQUIRED UNDER THE FOLLOWING CONDITIONS:
a. EVERY CHANGE OF HORIZONTAL DIRECTION EXCEEDING TWENTY TWO AND ONE-HALF DEGREES

b. ONE AND ONE-HALF METERS (1.50m) INSIDE THE PROPERTY LINES BEFORE THE HOUSE DRAINAGE
CONNECTION.
7.00

c. EVERY FIFTEEN METERS (15.00m) IN HORIZONTAL RUN OF PIPES.

d. AT THE END OF ANY HORIZONTAL PIPE LINES.
9.50

6.NOT LESS THAN 0.30 METER OF AIR SPACE MUST BE LEFT BETWEEN THE TOP OF THE SEWAGE
AND THE UNDER PART OF THE VAULT ROOF SLAB.
7. NO SEPTIC VAULT SHALL BE CONSTRUCTED UNDER THE BUILDING.

B 8.ALL PLUMBING WORKS SHALL BE UNDER THE SUPERVISION OF A LICENSED MASTER PLUMBER AND
A LICENSED PLUMBING CONTRACTOR.
2.50

C
TYPICAL 2nd & 3rd FLOOR WATER LINE LAYOUT
SCALE 1:100mts

1 2 3 4 5 6 7 8 9
36.00
9.00 9.00 9.00 9.00
4.50 4.50 4.50 4.50 4.50 4.50 4.50 4.50

A
7.00

G.V
9.50

C.O
B
S.P
2.50

VAC

V
C VS
VTR

WP
WS
GROUND FLOOR WATER LINE LAYOUT
SCALE 1:100mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 (ISOMETRIC)
PLUMBING LAYOUT
SCALE NTS

(ISOMETRIC)
COLD WATER LINE LAYOUT
SCALE NTS

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 1 2 3 4 5 6 7 8 9
36.00
4.50 9.00 9.00 9.00 4.50
4.50 4.50 4.50 4.50 4.50 4.50

7.00
9.50
B
2.50 DOWN TO F.A. STATION
AT 2ND & GROUND FLOOR

2ND & 3RD FLOOR POWER LAYOUT

SCALE 1:100mts

1 2 3 4 5 6 7 8 9
36.00
4.50 9.00 9.00 9.00 4.50
4.50 4.50 4.50 4.50 4.50 4.50

A
7.00
9.50

FACP FACP
LPA
OVERHEAD SERVICE MDP LPA
ENTRANCE REFER UP TO F.A. STATION
AT 2nd FLOOR
B
TO RISER DIAGRAM

TO FACP
2.50

RAMP UP
GROUND FLOOR POWER LAYOUT
SCALE 1:100mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 1 2 3 4 5 6 7 8 9
36.00
4.50 9.00 9.00 9.00 4.50
4.50 4.50 4.50 4.50 4.50 4.50

7.00
9.50
B

2.50
C
THIRD FLOOR LIGHTING LAYOUT
SCALE 1:100mts

7.00
9.50

B
2.50

C
SECOND FLOOR LIGHTING LAYOUT
SCALE 1:100mts

A
7.00
9.50

B
2.50

RAMP UP
GROUND FLOOR LIGHTING LAYOUT
SCALE 1:100mts

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER
 2 - 5.5mm2 THHN + 1 - 5.5mm TW(G) IN 25mm PVC

2 - 5.5mm2 THHN + 1 - 5.5mm TW(G) IN 25mm PVC

8167
230 ) = 28.41 AMPERES

2 - 3.5mm2 THHN WIRE STRANDED

1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC
PANEL BOARD DIAGRAM
SCALE NTS
2 - 3.5mm2 THHN WIRE STRANDED
1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC
2 - 3.5mm2 THHN WIRE STRANDED
1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC
2 - 3.5mm2 THHN WIRE STRANDED
1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC
2 - 3.5mm2 THHN WIRE STRANDED
1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC
2 - 3.5mm2 THHN WIRE STRANDED
1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC
2 - 3.5mm2 THHN WIRE STRANDED
1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC
2 - 3.5mm2 THHN WIRE STRANDED
1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC
2 - 3.5mm2 THHN WIRE STRANDED
1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC

7955
)
230 0.85 = 29.40 AMPERES
FLUORESCENT LIGHT FIXTURE MOUNTING DETAIL
SCALE 1:10mts

CEILING LINE

2 - 3.5mm2 THHN WIRE STRANDED OVERHEAD SERVICE

1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC ENTRANCE CONNECTED TO 4 - 2.0mm2 TW
2 - 3.5mm2 THHN WIRE STRANDED 230V AC, 1 2 WIRE, 60Hz IN 20mm PVC
1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC FITTED WITH 25mm TYPE "F" 3RD FLOOR LINE
2 - 3.5mm2 THHN WIRE STRANDED CONDUIT WEATHERHEAD
1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC 2 - 5.5mm2 THHN + 1 - 5.5mm
2 - 3.5mm2 THHN WIRE STRANDED TW(G) IN 25mm PVC
1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC
2 - 3.5mm2 THHN WIRE STRANDED
1 - 3.5mm TW(G) WIRE STRANDED 20mm PVC
4 - 2.0mm2 TW
IN 20mm PVC
2ND FLOOR LINE
5.00

2 - 5.5mm2 THHN + 1 - 5.5mm

3741
230 ) 0.80 = 13.01 AMPERES
KWHR METER

1 - 8.0mm2 TW GROUND
2
2 - 8.0mm THHN +
1-5.5mm2 TW(G) IN
TW(G) IN 25mm PVC

ENCLOSED ACB RATING:

4 - 2.0mm2 TW
IN 20mm PVC

IN 20mm PVC 20AT, 20AF, 230, 2P

1.80

25mm RSC
2 - 3.5mm2 THHN + 1 - 3.5mm2
GRD. FLOOR LINE TW(G) WIRE ON 20mm PVC
FIN. FLOOR LINE
LOAD SCHEDULE 1 - 5.5mm2 TW GROUND
IN 20mm PVC
SCALE NTS

ELECTRICAL RISER DIAGRAM

SCALE NTS

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

OFFICE OF THE DISTRICT ENGINEER