Scribd
Upload
580 views10 pages

Quick Guide (Tuya Smart)

This quick guide summarizes the setup and use of the CamnSmart PTZ Wi-Fi camera. [1] Download the Tuya Smart app and create an account. [2] Power on the camera and add it to the app by scanning the QR code with your phone. [3] The app interface allows viewing live video streams and configuring camera settings like motion detection recording to an SD card.

Uploaded by

andrew malson
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
580 views10 pages

Quick Guide (Tuya Smart)

This quick guide summarizes the setup and use of the CamnSmart PTZ Wi-Fi camera. [1] Download the Tuya Smart app and create an account. [2] Power on the camera and add it to the app by scanning the QR code with your phone. [3] The app interface allows viewing live video streams and configuring camera settings like motion detection recording to an SD card.

Uploaded by

andrew malson
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

Quick Guide

CamnSmart PTZ Wi-Fi Camera

1. Overview of the Cameras

Model: E27SX1TY
Model: E27XS2TY
Model: E27STY
Model: E27TY

www.camnsmart.com
2. Download APP and Register a user account and login
Search and download “Tuya Smart” in Apple Store or Android app store. Or scan
below QR code to download and install it to your phone.

If you are first time using this app, click “Sign up” to register an account according
to the procedure. After registration, you can login with your registered account.
In future login, if you forget your password, you can reset your password by clicking
"Forgot password” on the login page.

3. Add camera to App


1) Get ready your Wi-Fi router and remember your Wi-Fi password.
Note: A. please do not use special letters like "# % &" as Wi-Fi name and
password. B. Camera supports 2.4GHz Wi-Fi. If your Wi-Fi router is 5GHz, it
may be integrated with 2.4GHz. But 2.4GHz Wi-Fi and 5GHz Wi-Fi have the
same Wi-Fi SSID name. So, you can get to your Wi-Fi router's settings to set
2.4GHz Wi-Fi in a different name. Then you will see two Wi-Fi names listed
on your phone WLAN list. Your phone selects 2.4GHz Wi-Fi name to connect.
2) Please also open your location on your phone settings.
3) Login the app “Tuya Smart”
4) If you use SD card for video recording, please prepare an SD card and insert
it to the camera SD card slot.
(Note: Because camera need to run for video stream. It requires SD card
with high-speed reading and writing. So please use C10 (Class10) or higher
speed SD card. U3 type will be preferable.)
E27SX1TY E27STY E27TY
E27XS2TY

5) Connect camera to power socket and turn on power. Wait about a few
seconds, camera will rotate left-right and up-down. Then camera will say
“Welcome to use intelligent camera, please use QR code, net-pairing or AP
mode to configure the device”.

If camera does not rotate and no saying anything after 50 seconds, please
do following:
a) check power supplied properly and firmly.
b) please reset the camera. Below pictures show where are the reset buttons.
Use a pin to slightly press it for 10~15 seconds, till the camera say “Reset
successfully, please wait for reboot”. Release rest button, then the camera
will do start up again.

E27SX1TY E27STY E27TY


E27XS2TY
6) On the app, press “+” or “Add Device” button, Select “Camera & Lock”, select
“Smart Camera (Wi-Fi)”

7) Press “Next”.
On the Step 1), you already connected your phone to your Wi-Fi. So, it
automatically shows your Wi-Fi name. You just type in your Wi-Fi password,
then press “Next”.

Important note: you must type in correct Wi-Fi password, otherwise


connection will fail in following steps.
8) A QR code will show on your phone screen. Place the QR code in front of
the camera lens to let the camera read the QR code. You need to move the
QR code slowly forwards or backwards 10cm ~ 50cm distance to the camera
lens.

9) Once camera reads the QR code, it will say “Scan successfully, connecting
to the network” and say “connecting to the server”. Now press “I heard a
Prompt” button on app. Then just wait. Finally, it will say “configure
successfully, you may use the camera now.”

Camera is added successfully to you APP account. Now you can use it.

www.camnsmart.com
4. APP Interface

5. Settings Interface
6. Use SD card to record video
Recording modes option in settings:
1) Event recording: when camera detects motion, it will record video to SD card.
2) Non-Stop: it always records video to SD card.
(Please get to Settings / Storage Settings to set recording mode).

Notes:
1). First time to use SD card needs format the SD card.
2). After inserting SD card into camera, please get to Settings / Storage
Settings to turn on “Local Recording” and select your preferable Recording
Mode, event recording or non-stop recording.

www.camnsmart.com
This Quick Guide may be revised without further notice. Copy writes by CamnSmart.

You might also like