Scribd Logo
Upload

Welcome to Scribd!

  • 33 views

    Muelles Pickup Toyota

    Uploaded by

    Hugo Armando Garcia Lepe
    The document provides instructions for removing and installing rear leaf springs on a vehicle. It describes 7 steps to remove the leaf spring which include jacking up the vehicle, removing the rear wheel, disconnecting the shock absorber and parking brake cable, removing U-bolts and spring seats, and removing the hanger pin bolt and shackle pins. It also describes replacing eye bushings using a press and replacing defective leaf springs which involves bending open the spring clip, removing the center bolt, replacing the spring clip with a rivet, and reinstalling the center bolt.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Muelles Pickup Toyota

    Uploaded by

    Hugo Armando Garcia Lepe
    33 views4 pages
    The document provides instructions for removing and installing rear leaf springs on a vehicle. It describes 7 steps to remove the leaf spring which include jacking up the vehicle, removing the rear wheel, disconnecting the shock absorber and parking brake cable, removing U-bolts and spring seats, and removing the hanger pin bolt and shackle pins. It also describes replacing eye bushings using a press and replacing defective leaf springs which involves bending open the spring clip, removing the center bolt, replacing the spring clip with a rivet, and reinstalling the center bolt.

    Original Description:

    Como cambiar muelles de tacoma

    Original Title

    muelles pickup toyota

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for removing and installing rear leaf springs on a vehicle. It describes 7 steps to remove the leaf spring which include jacking up the vehicle, removing the rear wheel, disconnecting the shock absorber and parking brake cable, removing U-bolts and spring seats, and removing the hanger pin bolt and shackle pins. It also describes replacing eye bushings using a press and replacing defective leaf springs which involves bending open the spring clip, removing the center bolt, replacing the spring clip with a rivet, and reinstalling the center bolt.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    33 views4 pages

    Muelles Pickup Toyota

    Uploaded by

    Hugo Armando Garcia Lepe
    The document provides instructions for removing and installing rear leaf springs on a vehicle. It describes 7 steps to remove the leaf spring which include jacking up the vehicle, removing the rear wheel, disconnecting the shock absorber and parking brake cable, removing U-bolts and spring seats, and removing the hanger pin bolt and shackle pins. It also describes replacing eye bushings using a press and replacing defective leaf springs which involves bending open the spring clip, removing the center bolt, replacing the spring clip with a rivet, and reinstalling the center bolt.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    SA−149

    SUSPENSION AND AXLE − REAR SUSPENSION

    REAR LEAF SPRING


    COMPONENTS
    SA−150
    SUSPENSION AND AXLE − REAR SUSPENSION

    REAR LEAF SPRING REMOVAL


    Installation is in the reverse order of removal.
    1. SUPPORT BODY
    (a) Jack up and support the body on stands.
    (b) Lower the axle housing until the leaf spring tension is
    free, and keep it at this position.
    2. REMOVE REAR WHEEL
    Torque: 110 N−m (1,150 kgf−cm, 83 ft−lbf)
    3. 4WD:
    DISCONNECT PARKING BRAKE CABLE
    4. DISCONNECT REAR SHOCK ABSORBER
    Remove the bolt and disconnect the shock absorber
    from the spring seat.
    Torque:
    2WD 26 N−m (260 kgf−cm, 19 ft−lbf)
    4WD 71 N−m (730 kgf−cm, 53 ft−lbf)

    5. REMOVE U− BOLTS
    (a) Remove the 4 U−bolt mounting nuts.
    (b) Remove the spring seat, pads and pad retainer.
    (c) Remove the U−bolts.
    Torque: 120 N−m (1,250 kgf−cm, 90 ft−lbf)
    INSTALLATION HINT: Tighten the U−bolts so that
    the length of all the U−bolts under the spring seat are
    the same.
    (d) 4WD:
    Remove the spring bumper.
    6. REMOVE LEAF SPRING
    (a) Remove the nut, washer and hanger pin bolt.
    Torque: 155 N−m (1,600 kgf−cm, 115 ft−lbf)
    INSTALLATION HINT: After stabilizing the suspen−
    sion, torque the nut.

    (b) Remove the 2 shackle pin mounting nuts.


    Torque: 81 N−m (930 kgf−cm, 67 ft−lbf)
    INSTALLATION HINT: After stabilizing the suspen−
    sion, torque the nut.
    (c) Remove the shackle pin and plate, and remove the
    rear leaf spring.
    SA−151
    SUSPENSION AND AXLE − REAR SUSPENSION

    7. 2WD:
    REMOVE SPRING BUMPER
    Torque: 29 N−m (300 kgf−cm, 22 ft−lbf)

    EYE BUSHING REPLACEMENT


    REPLACE BUSHING
    Using SST and a press, replace the eye bushing.
    SST 09550−10012 (09252−10010, 09553−10010)

    2WD:
    When installing the bushing, as shown in the illustra−
    tion.

    LEAF SPRING REPLACEMENT


    1. BEND OPEN SPRING CLIP
    Using a chisel and hammer, pry up the spring clip.

    2. REMOVE CENTER BOLT


    Hold the spring near the center bolt in a vise and
    remove the center bolt.
    SA−152
    SUSPENSION AND AXLE − REAR SUSPENSION

    3. REPLACE SPRING CLIP


    (a) Drill off the head of the rivet and drive it out.
    (b) Install a new rivet into the holes of the spring leaf and
    clip. Then rivet with a press.

    4. INSTALL SPRING CENTER BOLT


    (a) Align the leaf holes and secure the leaves with a vise.
    (b) Install the spring center bolt.
    Torque: 44 N−m (450 kgf−cm, 33 ft−lbf)

    5. BEND SPRING CLIP


    Using a hammer, bend the spring clip into the position.

    You might also like