The document describes how to establish a static routing between two routers. It is a 4 step process: 1) Build the topology and assign IP addresses to devices; 2) Assign IP addresses to the routers; 3) Add static routes to the routers to route traffic between their directly connected networks; 4) Verify connectivity between networks by pinging from one PC to the other using the new static route.
The document describes how to establish a static routing between two routers. It is a 4 step process: 1) Build the topology and assign IP addresses to devices; 2) Assign IP addresses to the routers; 3) Add static routes to the routers to route traffic between their directly connected networks; 4) Verify connectivity between networks by pinging from one PC to the other using the new static route.
The document describes how to establish a static routing between two routers. It is a 4 step process: 1) Build the topology and assign IP addresses to devices; 2) Assign IP addresses to the routers; 3) Add static routes to the routers to route traffic between their directly connected networks; 4) Verify connectivity between networks by pinging from one PC to the other using the new static route.
The document describes how to establish a static routing between two routers. It is a 4 step process: 1) Build the topology and assign IP addresses to devices; 2) Assign IP addresses to the routers; 3) Add static routes to the routers to route traffic between their directly connected networks; 4) Verify connectivity between networks by pinging from one PC to the other using the new static route.
Download as DOC, PDF, TXT or read online from Scribd
Download as doc, pdf, or txt
You are on page 1/ 3
ESTABLISH A STATIC ROUTING BETWEEN TWO ROUTERS
AIM: To establish a static routing between two routers.
APPARATUS: NetSim Software Version 12.0.18
PROCEDURE:
Step 1: Open Packet tracer, and build the topology
Select Switches and Routers from Networking devices which is present at bottom left of the packet tracer interface drop them on the workspace. Select PC from end devices which is present at bottom left of the packet tracer interface drop them on the workspace. Select the appropriate connector from connections icon and connect the devices as shown below.
Step 2: Assign IP addresses to PCs, Router
To assign IP addresses to the PCs a) Click on PC b) Select Desktop option c) Select IP configuration d) Give the IP address , press enter the subnet mask will be automatically assigned e) Give the default gateway address(if the topology requires)
Assign IP addresses Routers
a) R1(config)#interface g0/0/0 R1(config-if)#ip address 10.0.0.1 255.0.0.0 R1(config-if)#no shutdown R1(config-if)#exit R1(config)#interface g0/0/1 R1(config-if)#ip address 20.0.0.1 255.0.0.0 R1(config-if)#no shutdown R1(config-if)#exit b) R2(config)#interface g0/0/0 R2(config-if)#ip address 30.0.0.1 255.0.0.0 R2(config-if)#no shutdown R2(config-if)#exit R2(config)#interface g0/0/1 R2(config-if)#ip address 20.0.0.1 255.0.0.0 R2(config-if)#no shutdown R2(config-if)#exit Step 3: Adding static route Static Routing between the routers, By default, Routers Know only directed connected networks here Router 1 know only 10.0.0.0 and 20.0.0.0 it doesn't know the 30.0.0.0 like this R2 doesn't know about 10.0.0.0.So We are going to add Static route to this both router
In Router R1,Just give this command, In this case Destination is 30.0.0.0 and its subnet mask is 255.0.0.0 next hop address is 20.0.0.2 a) R1(config)#ip route 30.0.0.0 255.0.0.0 20.0.0.2 R2(config)#ip route 10.0.0.0 255.0.0.0 20.0.0.1 Step 4: Checking the connectivity using ping command a) Open PC0 b) Select Desktop Option c) Select command Prompt Give the command as Ping 30.0.0.1 RESULT:
Download Advanced Intelligent Systems for Sustainable Development AI2SD 2019 Volume 6 Advanced Intelligent Systems for Networks and Systems Mostafa Ezziyyani ebook All Chapters PDF
